BA5955FP_1 [ROHM]
Power Driver for DVD-RAMs; 对于DVD- RAM的功率驱动器
| 型号： | BA5955FP_1 |
| 厂家： | 
ROHM |
| 描述： | Power Driver for DVD-RAMs |
| 文件： | 总6页 (文件大小：95K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
1/5
Structure
Product Name
:
:
Silicon Monolithic Integrated Circuit
Power Driver for DVD-RAMs
Device Name
Features
:
:
BA5955FP
• 2-ch current feedback-type BTL driver
• Use of an HSOP25PIN power package allows downsizing of the set.
• A wide dynamic range
• A built-in thermal shutdown circuit installed.
• The pre stage (PRE part) and the output stage (POW part) are separated to
achieve an efficient drive.
• A built-in standby function installed.
{ ABSOLUTE MAXIMUM RATINGS (Ta=25°C)
Parameter
Symbol
Vcc
Limits
18
Unit
Ｖ
Power Supply Voltage
Power Dissipation
Maximum Output
Current
Pd
1.45*1
W
Iomax
Topr
1*2
A
Operating Temperature
Range
Storage Temperature
Range
-35 to 85
-55 to 150
°C
°C
Tstg
*1 When mounted on the glass/epoxy board with the size: 70 mm×70 mm, the thickness: 1.6 mm, and
the rate of copper foil occupancy area: 3% or less.
Over Ta=25°C, derating at the rate of 11.6mW/°C.
*2 The power dissipation should be specified within the ASO range.
{ OPERATING CONDITIONS
Parameter
Pre-stage Power Supply
Voltage
Symbol
PreVcc
Limits
Unit
V
PowVcc+3 to 14
Output-stage Power
Supply Voltage
PowVcc
4.5 to 11
V
This product has not been checked for the strategic materials (or service) defined in the Foreign
Exchange and Foreign Trade Control Low of Japan so that a verification work is required before
exporting it.
Not designed for radiation resistance.
REV. A
2/5
{ ELECTRIC CHARACTERISTICS (Ta=25°C, PreVcc=12V , PowVcc=5V, Vc=2V, RL=6Ω+150uH,
Rd=0.5Ω, unless otherwise noted.)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
Condition
Standby Consumption
Current
IST
-
0.1
1
mA
At standby
Quiescent
Consumption Current
IQpre
Ioof
-
21
-
32
6
mA
mA
V
Output Offset Current
-6
Maximum Output
Amplitude 1
VOM1
3.6
3.9
-
Maximum Output
Amplitude 2
VOM2
5.8
6.1
-
V
When POWVcc= 8V
Transfer Gain
Gm
0.9
-
1
-
1.1
0.5
-
A/V
V
VIN= ±0.2V
STBY ON Voltage
STBY OFF Voltage
VSON
VSOFF
2
-
V
<Current Detection Amplifier>
Output Voltage (at no
signal)
Vodet
1.9
5.0
1.0
1.0
-
2.0
6.0
-
2.1
V
Closed Circuit Voltage
Gain
Output Driving Current
Sink
Output Driving Current
Source
Gvdet
ISIdet
ISOdet
SRdet
GBW
7.0
dB
-
-
-
-
mA
mA
V/µs
MHz
-
100KHz square wave 2Vp-p
output
Slew Rate
1
Voltage Gain
Bandwidth Product
-
10
<Reset>
Output Voltage in
non-operation
Output Voltage in
operation
3.3V PULL UP with 10KΩ
attached
3.3V PULL UP with 10KΩ
attached
VRSTOFF
VRSTON
2.8
-
-
-
-
V
V
0.5
{ OUTLINE DIMENSIONS, SYMBOLS
Product Number
(UNIT: mm)
REV. A
3/5
{ APPLICATION CIRCUIT DIAGRAM
Focus coil
0.5Ω
μ-CO M
A /D
FO CU S
12V
5V
18
25
24
23
22
21
20
19
17
16
15
14
LEV EL
SH IFT
PreV cc
Pow V cc
V /I
PreV cc/V c
D ETECTER
T.S.D .
V /I
Pow V cc
LEV EL
SH IFT
STBY
L:STBY
V c
1
2
3
4
5
6
7
8
9
10
11
12
13
μ-CO M
A /D
STA N D -BY
V C
TRA CK IN G
10K
Tracking coil
0.5Ω
T.S.D: (Thermal shutdown)
Resistance unit: [Ω]
{ PIN Description
No.
Pin Name
Description
No.
Pin Name
Description
1
2
Vc
Reference input for input signal
CH1 input
25
24
PreVcc
IN2
Pre stage power supply terminal
CH2 input
IN1
Error amp phase compensation
external terminal 1
Error amp phase compensation
external terminal 2
3
FIL1
23
FIL2
4
5
EOUT1
CH1 error amp output
22
21
EOUT2
CH2 error amp output
DETOUT1
CH1 current detection amp output
DETOUT2
CH2 current detection amp output
CH1 current detection amp
non-inverted input
CH2 current detection amp
non-inverted input
6
DETIN1P
20
DETIN2P
7
8
GND
Substrate GND
Reset output
RESET
19
18
GND
Substrate GND
Output stage power supply
terminal
9
STBY
Standby input
PowVcc
CH1 current detection amp inverted
input
CH2 current detection amp
inverted input
10
DETIN1M
17
DETIN2M
11
12
13
OUT1M
OUT1P
OUT1P
CH1 negative output
CH1 positive output
CH1 positive output
16
15
14
OUT2M
OUT2P
OUT2P
CH2 negative output
CH2 positive output
CH2 positive output
REV. A
4/5
{ CAUTIONS ON USE
(1) The BA5955FP incorporates a TSD circuit (overheat protection circuit) and a reset circuit. When the
chip temperature has reached 175℃ (typ.), the output current will be muted while the reset output will
become ‘L’ and, when the chip temperature has dropped to 150℃ (typ.), the mute function will be reset
while the reset output will be ‘H.’ The reset output also becomes ‘L’ in the standby state.
(2) When the power supply voltage (PreVcc) has dropped to 3.8V (typ.) or less, the output current will be
muted while the reset output will become ‘L’ and, when PreVcc has recovered to 4.0V (typ.), the driver
part circuit will be initiated to set the reset output to ‘H.’
(3) When the reference input (Vc) voltage has dropped to 0.8V (typ.) or less, the output current will be
muted while the reset output will become ‘L.’
Under conditions of normal use, it should be 1.2V (typ.) or above.
(4) Thermal shutdown or a drop of reference voltage or power supply voltage will activate the mute
function, where only the driver part can be muted. While muting, the voltage at the output terminal will
equal to the internal reference voltage (approximately PowVcc/2).
(5) Connecting a capacitive load to the OP-AMP output results in a phase margin reduction of the amp and
may cause an oscillation or a peak. When connecting a capacitive load, a resistance must be
inserted in series between the output and the capacitive load. And after careful consideration of the
frequency characteristics, the device should be used within the range where no problem is found in
actual use.
(6) A radiating fin must be connected to the external GND.
(7) Short-circuits between output pin-VCC, output pin-GND, or output terminals (load short) must be
avoided.
Mounting the ICs in improper directions may damage them or produce smoke.
(8) About absolute maximum ratings
Exceeding the absolute maximum ratings, such as the applied voltage or the operating temperature
range, may cause permanent device damage. As these cases cannot be limited to the broken short
mode or the open mode, if a special mode where the absolute maximum ratings may be exceeded is
assumed, it is recommended to take mechanical safety measures such as attaching fuses.
(9) About power supply lines
As a measure against the back current regenerated by a counter electromotive force of the motor, a
capacitor to be used as a regenerated-current path can be installed between the power supply and
GND and its capacitance value should be determined after careful check that any problems, for
example, a leak capacitance of the electrolytic capacitor at low temperature, are not found in various
characteristics.
(10) About GND potential
The electric potential of the GND terminal must be kept lowest in the circuitry at any operation states.
(11) About thermal design
With consideration of the power dissipation (Pd) under conditions of actual use, a thermal design
provided with an enough margin should be done.
(12) About operations in a strong electric field
When used in a strong electric field, note that a malfunction may occur.
(13) ASO
When using this IC, the output Tr must be set not to exceed the values specified in the absolute
maximum ratings and ASO.
(14) Thermal shutdown circuit
This IC incorporates a thermal shutdown circuit (TSD circuit). When the chip temperature reaches the
value shown below, the coil output to the motor will be set to open.
The thermal shutdown circuit is designed only to shut off the IC from a thermal runaway and not
intended to protect or guarantee the entire IC functions.
Therefore, users cannot assume that the TSD circuit once activated can be used continuously in the
subsequent operations.
TSD ON Temperature
[°C] (typ.)
Hysteresis Temperature
[°C] (typ.)
175
25
REV. A
5/5
(15) About earth wiring patterns
When a small signal GND and a large current GND are provided, it is recommended that the large
current GND pattern and the small signal GND pattern should be separated and grounded at a single
point of the reference point of the set in order to prevent the voltage of the small signal GND from being
affected by a voltage change caused by the resistance of the pattern wiring and the large current.
Make sure that the GND wiring patterns of the external components will not change, too.
(16) This IC is a monolithic IC which has a P+ isolations and P substrate to isolate elements each other.
This P layer and an N layer in each element form a PN junction to construct various parasitic elements.
Due to the IC structure, the parasitic elements are inevitably created by the potential relationship.
Activation of the parasitic elements can cause interference between circuits and may result in a
malfunction or, consequently, a fatal damage. Therefore, make sure that the IC must not be used
under conditions that may activate the parasitic elements, for example, applying the lower voltage than
the ground level (GND, P substrate) to the input terminals.
In addition, do not apply the voltage to input terminals without applying the power supply voltage to the
IC. Also while applying the power supply voltage, the voltage of each input terminal must not be over
the power supply voltage, or within the guaranteed values in the electric characteristics.
<Supplemental Remarks>
Current feedback driver
The transfer gain (output current/input current) can be determined by the following equation:
1
gm =
(A/V)
2R
d
Rd = Resistance for current detection (Ω)
REV. A
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
THE AMERICAS / EUPOPE / ASIA / JAPAN
ROHM Customer Support System
Contact us : webmaster@ rohm.co.jp
www.rohm.com
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Copyright © 2007 ROHM CO.,LTD.
21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
Appendix1-Rev2.0
相关型号：
©2020 ICPDF网 联系我们和版权申明