BA4560RFJ-E2 [ROHM]
Low Noise Operational Amplifiers; 低噪声运算放大器
| 型号： | BA4560RFJ-E2 |
| 厂家： | 
ROHM |
| 描述： | Low Noise Operational Amplifiers |
| 文件： | 总44页 (文件大小：581K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Datasheet
Operational Amplifiers
Low Noise Operational Amplifiers
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
●General Description
Normal BA4560 and high-reliability BA4560R / BA4564R/BA4564W integrate two or four independent Op-Amps on a single
chip. Especially, this series is suitable for any audio applications due to low noise and low distortion characteristics and
there are usable for other many applications by wide operating supply voltage range.
BA4560R / BA4564R / BA4564W are high-reliability products with extended operating temperature range and high ESD
tolerance.
●Features
●Key Specification
High voltage gain, low noise, low distortion
Wide operating supply voltage
Wide Operating Supply Voltage
(split supply):±4V to ±15V
Internal ESD protection circuit
Wide Operating Temperature Range
Wide Temperature Range:
BA4560
-40°C to +85°C
-40°C to +105°C
4V/µs(typ.)
BA4560R/BA4564R/BA4564W
High Slew Rate:
Total Harmonic Distortion:
●Packages
W(Typ.) x D(Typ.) x H(Max.)
SOP8
MSOP8
SSOP-B8
TSSOP-B8
SOP-J8
5.00mm x 6.20mm x 1.71mm
2.90mm x 4.00mm x 0.90mm
3.00mm x 6.40mm x 1.35mm
3.00mm x 6.40mm x 1.00mm
4.90mm x 6.00mm x 1.65mm
5.00mm x 6.40mm x 1.35mm
0.003%(typ.)
Input Referred Noise Voltage:
Low Offset Voltage:
BA4564W
8nV/ Hz (typ.)
2.5mV(max.)
SSOP-B14
●Selection Guide
Maximum Operation Temperature
+85°C
Slew Rate
4V/µs
BA4560F
Normal
Dual
BA4560FJ
BA4560FV
BA4560FVT
BA4560FVM
+105°C
Slew Rate
4V/µs
BA4560RF
BA4560RFJ
BA4560RFV
BA4560RFVT
BA4560RFVM
High Reliability
Dual
BA4564RFV
BA4564WFV
Quad
4V/µs
●Block Diagram
VCC
IN
IN
－
＋
VOUT
VEE
Fig. 1 Simplified schematic
○Product structure：Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･14･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
1/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
●Pin Configuration(TOP VIEW)
1
2
3
14 OUT4
OUT1
13
12
OUT1
-IN1
+IN1
VEE
VCC
OUT2
-IN2
+IN2
-IN4
+IN4
1
2
3
4
8
7
6
5
-IN1
+IN1
VCC
CH1
+
CH4
+ -
-
CH1
- +
4
5
11
10
VEE
+IN3
-IN3
OUT3
+IN2
-IN2
CH2
+ -
+ -
CH3
- +
CH2
6
7
9
8
OUT2
SSOP-B14
SOP8
SOP-J8
SSOP-B8
TSSOP-B8
MSOP8
Package
SOP8
SSOP-J8
SSOP-B8
TSSOP-B8
MSOP8
SSOP-B14
BA4560F
BA4560RF
BA4560FJ
BA4560RFJ
BA4560FV
BA4560RFV
BA4560FVT
BA4560RFVT
BA4560FVM
BA4560RFVM
BA4564RFV
BA4564WFV
●Ordering Information
B A 4
5
6
x
x
x
x
x
-
x x
Part Number
BA4560xxx
BA4560Rxxx
BA4564RFV
BA4560WFV
Package
: SOP8
FJ : SOP-J8
FV : SSOP-B8
: SSOP-B14
FVM : MSOP8
FVT : TSSOP-B8
Packaging and forming specification
E2: Embossed tape and reel
(SOP8/SSOP-B8/TSSOP-B8/SOP-J8
SSOP-B14)
TR: Embossed tape and reel
(MSOP8)
F
●Line-up
Operating Supply
Voltage
(split supply)
Supply
Current
(Typ.)
Offset
Voltage
(max.)
Orderable
Package
Topr
Part Number
SOP8
Reel of 2500 BA4560F-E2
Reel of 2500 BA4560FJ-E2
SOP-J8
-40°C to +85°C
4mA
SSOP-B8
Reel of 2500 BA4560FV-E2
TSSOP-B8 Reel of 2500 BA4560FVT-E2
MSOP8
SOP8
Reel of 3000 BA4560FVM-TR
Reel of 2500 BA4560RF-E2
Reel of 2500 BA4560RFJ-E2
Reel of 2500 BA4560RFV-E2
6mV
±4.0V to ±15.0V
SOP-J8
SSOP-B8
3mA
6mA
-40°C to +105°C
TSSOP-B8 Reel of 3000 BA4560RFVT-E2
MSOP8
Reel of 3000 BA4560RFVM-TR
Reel of 2500 BA4564RFV-E2
Reel of 2500 BA4564WFV-E2
SSOP-B14
SSOP-B14
2.5mV
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
2/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
●Absolute Maximum Ratings (Ta=25℃)
○BA4560, BA4560R, BA4564R, BA4564W
Ratings
BA4560R BA4564R
Parameter
Supply Voltage
Symbol
Unit
BA4560
BA4564W
VCC-VEE
+36
V
SOP8
552*1*6
540*2*6
500*3*6
500*3*6
470*4*6
-
690*1*6
675*2*6
625*3*6
625*3*6
587*4*6
-
-
-
SOP-J8
SSOP-B8
TSSOP-B8
MSOP8
-
-
-
-
Power dissipation
Pd
mW
-
-
-
-
SSOP-B14
875*5*6
+36
875*5*6
Differential Input Voltage*7
Input Common-mode voltage
range
Vid
VCC-VEE
V
V
Vicm
VEE to VCC
(VEE-0.3) to VEE+36
Operating Supply Voltage
Operating Temperature
Storage Temperature
Vopr
Topr
+8 to +30 (±4 to ±15)
-40 to +105
-55 to +150
+150
V
-40 to +85
-55 to +125
+125
℃
℃
℃
Tstg
Maximum junction Temperature
Tjmax
Note: Absolute maximum rating item indicates the condition which must not be exceeded.
Application of voltage in excess of absolute maximum rating or use out absolute maximum rated temperature environment may cause
deterioration of characteristics.
*1
*2
*3
*4
*5
*6
*7
To use at temperature above Ta＝25℃ reduce 5.52mW.
To use at temperature above Ta＝25℃ reduce 5.4mW.
To use at temperature above Ta＝25℃ reduce 5mW.
To use at temperature above Ta＝25℃ reduce 4.7mW.
To use at temperature above Ta＝25℃ reduce 7mW.
Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm).
The voltage difference between inverting input and non-inverting input is the differential input voltage.
Then input terminal voltage is set to more than VEE.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
3/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
●Electrical Characteristics
○BA4560 (Unless otherwise specified VCC=+15V, VEE=-15V)
Limits
Temperature
Range
Parameter
Input Offset Voltage *8
Input Offset Current *8
Input Bias Current *9
Symbol
Vio
Unit
Condition
Min.
-
Typ.
Max.
6
25℃
25℃
25℃
25℃
0.5
mV VOUT=0V
nA VOUT=0V
nA VOUT=0V
Iio
-
-
-
5
50
4
200
500
7.5
Ib
RL=∞, All Op-Amps,
VIN+=0V
Supply Current
ICC
mA
V
25℃
25℃
±12
±10
±14
±13
-
-
RL≧10kΩ
RL≧2kΩ
Maximum Output Voltage
Large Signal Voltage Gain
Input Common-mode Voltage Range
Common-mode Rejection Ratio
Power Supply Rejection Ratio
Slew Rate
VOM
AV
RL≧2kΩ, VO=±10V
Vicm=0V
25℃
25℃
25℃
25℃
25℃
25℃
25℃
25℃
86
100
±14
90
90
4
-
-
-
-
-
-
-
-
-
dB
V
Vicm
CMRR
PSRR
SR
±12
VOUT=±12V
70
dB VOUT=±12V
dB Ri≦10kΩ
76.3
-
-
-
-
-
-
V/μs AV=0dB, RL=2kΩ
MHz RL=2kΩ
Unity Gain Frequency
Unity Gain Frequency
Total Harmonic Distortion
ft
4
GBW
THD+N
10
0.003
8
MHz f=10kHz
AV=20dB, RL=10kΩ
%
VIN=0.05Vrms, f=1kHz
RS=100Ω, Vi=0V
nV/ Hz
f=1kHz
Input Referred Noise Voltage
Vn
25℃
RS=2.2Ω, RIAA
BW=10kHz to 30kHz
-
2.2 μVrms
*8
*9
Absolute value
Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
4/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560R (Unless otherwise specified VCC=+15V, VEE=-15V, Full range -40℃ to +105℃)
Limits
Temperature
Range
Parameter
Input Offset Voltage *10
Input Offset Current *10
Input Bias Current *11
Symbol
Vio
Unit
Condition
Min.
Typ.
Max.
25℃
Full range
25℃
-
0.5
6
mV VOUT=0V
nA VOUT=0V
nA VOUT=0V
-
-
7
-
5
200
Iio
Full range
25℃
-
-
200
-
50
500
Ib
Full range
25℃
-
-
3
800
-
-
7
RL=∞,All Op-Amps
VIN+=0V
Supply Current
ICC
VOM
AV
mA
V
Full range
25℃
-
7.5
±12
±14
±11.5
100
-
-
-
-
-
-
-
RL≧2kΩ
Maximum Output Voltage
Large Signal Voltage Gain
Input Common-mode Voltage Range
Common-mode Rejection Ratio
Power Supply Rejection Ratio
Channel Separation
Full range ±10
Io=25mA
25℃
Full range
25℃
86
83
RL≧2kΩ, VO=±10V
Vicm=0V
dB
V
±12
±14
-
Vicm
CMRR
PSRR
CS
VOUT=±12V
Full range ±12
25℃
25℃
25℃
25℃
25℃
25℃
70
90
90
-
-
-
-
-
-
-
-
dB VOUT=±12V
dB Ri≦10kΩ
76.5
-
-
-
-
-
-
105
4
dB R1=100Ω,f=1kHz
AV=0dB, RL=10kΩ
CL=100pF
Slew Rate
SR
V/μs
Unity Gain Frequency
Total Harmonic Distortion
ft
4
MHz RL=2kΩ
AV=20dB, RL=10kΩ
%
THD+N
0.003
8
VIN=0.05Vrms, f=1kHz
RS=100Ω, Vi=0V
nV/ Hz
f=1kHz
Input Referred Noise Voltage
Vn
25℃
1.0
μVrms DIN-AUDIO
*10 Absolute value
*11 Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
5/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564R (Unless otherwise specified VCC=+15V, VEE=-15V, Full range -40℃ to +105℃)
Limits
Temperature
Range
Parameter
Input Offset Voltage *12
Input Offset Current *12
Input Bias Current *13
Symbol
Vio
Unit
Condition
Min.
Typ.
Max.
25℃
Full range
25℃
-
0.5
6
7
mV VOUT=0V
nA VOUT=0V
nA VOUT=0V
-
-
-
5
200
200
500
800
14
15
-
Iio
Full range
25℃
-
-
-
50
Ib
Full range
25℃
-
-
6
-
-
RL=∞,All Op-Amps
VIN+=0V
Supply Current
ICC
VOM
AV
mA
V
Full range
25℃
-
±12
±14
±11.5
100
-
RL≧2kΩ
Maximum Output Voltage
Large Signal Voltage Gain
Input Common-mode Voltage Range
Common-mode Rejection Ratio
Power Supply Rejection Ratio
Channel Separation
Full range ±10
-
Io=25mA
25℃
Full range
25℃
86
83
-
RL≧2kΩ, VOUT=±10V
Vicm=0V
dB
V
-
±12
±14
-
-
Vicm
CMRR
PSRR
CS
VOUT=±12V
Full range ±12
-
25℃
25℃
25℃
25℃
25℃
25℃
70
90
90
-
-
-
-
-
-
-
-
dB VOUT=±12V
dB Ri≦10kΩ
76.5
-
-
-
-
-
-
105
4
dB R1=100Ω, f=1kHz
AV=0dB, RL=10kΩ
CL=100pF
Slew Rate
SR
V/μs
Unity Gain Frequency
Total Harmonic Distortion
ft
4
MHz RL=2kΩ
AV=20dB, RL=10kΩ
%
THD+N
0.003
8
VIN=0.05Vrms, f=1kHz
RS=100Ω, Vi=0V
nV/ Hz
f=1kHz
Input Referred Noise Voltage
Vn
25℃
1.0
μVrms DIN-AUDIO
*12 Absolute value
*13 Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
6/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564W (Unless otherwise specified VCC=+15V, VEE=-15V, Full range -40℃ to +105℃)
Limits
Temperature
Range
Parameter
Symbol
BA4564WFV
Unit
Condition
Min.
Typ.
Max.
25℃
Full range
25℃
-
0.5
2.5
4
Input Offset Voltage *14
Input Offset Current *14
Input Bias Current *15
Vio
Iio
mV VOUT=0V
nA VOUT=0V
nA VOUT=0V
-
-
-
5
200
200
300
500
11
13
-
Full range
25℃
-
-
-
50
Ib
Full range
25℃
-
-
6
-
-
RL=∞,All Op-Amps
VIN+=0V
Supply Current
ICC
VOM
AV
mA
V
Full range
25℃
-
±12
±14
±11.5
100
-
RL≧2kΩ
Maximum Output Voltage
Large Signal Voltage Gain
Input Common-mode Voltage Range
Common-mode Rejection Ratio
Power Supply Rejection Ratio
Channel Separation
Full range ±10
-
Io=25mA
25℃
Full range
25℃
86
83
-
RL≧2kΩ, VOUT=±10V
Vicm=0V
dB
V
-
±12
±14
-
-
Vicm
CMRR
PSRR
CS
VOUT=±12V
Full range ±12
-
25℃
25℃
25℃
25℃
25℃
25℃
70
90
90
-
-
-
-
-
-
-
-
dB VOUT=±12V
dB Ri≦10kΩ
76.5
-
-
-
-
-
-
105
4
dB R1=100Ω, f=1kHz
AV=0dB, RL=10kΩ
CL=100pF
Slew Rate
SR
V/μs
Unity Gain Frequency
Total Harmonic Distortion
ft
4
MHz RL=2kΩ
AV=20dB, RL=10kΩ
%
THD+N
0.003
8
VIN=0.05Vrms, f=1kHz
RS=100Ω, Vi=0V
f=1kHz
nV/ Hz
Input Referred Noise Voltage
Vn
25℃
1.0
μVrms DIN-AUDIO
*14 Absolute value
*15 Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
7/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
Description of electrical characteristics
Described here are the terms of electric characteristics used in this datasheet. Items and symbols used are also shown.
Note that item name and symbol and their meaning may differ from those on another manufacture’s document or general document.
1. Absolute maximum ratings
Absolute maximum rating item indicates the condition which must not be exceeded. Application of voltage in excess of
absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of
characteristics.
1.1 Power supply voltage (VCC-VEE)
Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power
supply terminal without deterioration or destruction of characteristics of internal circuit.
1.2 Differential input voltage (Vid)
Indicates the maximum voltage that can be applied between non-inverting terminal and inverting terminal without
deterioration and destruction of characteristics of IC.
1.3 Input common-mode voltage range (Vicm)
Indicates the maximum voltage that can be applied to non-inverting terminal and inverting terminal without
deterioration or destruction of characteristics. Input common-mode voltage range of the maximum ratings not assure
normal operation of IC. When normal operation of IC is desired, the input common-mode voltage of characteristics
item must be followed.
1.4 Power dissipation (Pd)
Indicates the power that can be consumed by specified mounted board at the ambient temperature 25℃(normal temperature).
As for package product, Pd is determined by the temperature that can be permitted by IC chip in the package
(maximum junction temperature)and thermal resistance of the package.
2. Electrical characteristics item
2.1 Input offset voltage (Vio)
Indicates the voltage difference between non-inverting terminal and inverting terminal. It can be translated into the
input voltage difference required for setting the output voltage at 0 V .
2.2 Input offset current (Iio)
Indicates the difference of input bias current between non-inverting terminal and inverting terminal.
2.3 Input bias current (Ib)
Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias current at
non-inverting terminal and input bias current at inverting terminal.
2.4 Input common-mode voltage range(Vicm)
Indicates the input voltage range where IC operates normally.
2.5 Large signal voltage gain (AV)
Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal
and Inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage.
Av = (Output voltage fluctuation) / (Input offset fluctuation)
2.6 Circuit current (ICC)
Indicates the IC current that flows under specified conditions and no-load steady status.
2.7 Output saturation voltage (VOM)
Signifies the voltage range that can be output under specific output conditions.
2.8 Common-mode rejection ratio (CMRR)
Indicates the ratio of fluctuation of input offset voltage when in-phase input voltage is changed. It is normally the
fluctuation of DC.
CMRR = (Change of Input common-mode voltage) / (Input offset fluctuation)
2.9 Power supply rejection ratio (PSRR)
Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed. It is normally the fluctuation
of DC.
PSRR = (Change of power supply voltage) / (Input offset fluctuation)
2.10 Unity gain frequency (ft)
Indicates a frequency where the voltage gain of operational amplifier is 1.
2.11 Slew Rate (SR)
SR is a parameter that shows movement speed of operational amplifier. It indicates rate of variable output voltage
as unit time.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
8/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
2.12 Gain Band Width (GBW)
Indicates to multiply by the frequency and the gain where the voltage gain decreases 6dB/octave.
2.13 Total harmonic distortion + Noise (THD+N)
Indicates the fluctuation of input offset voltage or that of output voltage with reference to the change of output voltage
of driven channel.
2.14 Input referred noise voltage (Vn)
Indicates a noise voltage generated inside the operational amplifier equivalent by ideal voltage source connected in
series with input terminal.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
9/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
●Typical Performance Curves
○BA4560
8.0
1000
800
600
400
200
0
-40℃
BA4560F
6.0
4.0
2.0
0.0
25℃
BA4560FJ
BA4560FV/FVT
BA4560FVM
85℃
0
5
10
15
20
25
30
35
0
25
50
75
100
125
℃
SUPPLY VOLTAGE [V]
AMBIE NT TE MP ERTURE [
]
.
Fig.2
Derating Curve
Fig.3
Supply Current - Supply Voltage
30
25
20
15
10
5
8.0
6.0
4.0
2.0
0.0
±15V
±7.5 V
±4 V
0
-50
-25
0
25
50
75
100
0.1
1
LOAD RESISTANCE [k
10
AMBIENT TEMPERATURE [
]
℃
]
Ω
Fig.4
Fig.5
Supply Current - Ambient Temperature
Maximum Output Voltage Swing
- Load Resistance
(VCC/VEE=+15V/-15V,Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
10/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560
20
20
15
10
5
15
10
5
VOH
VOH
0
0
-5
-5
VOL
-10
-15
-20
-10
-15
-20
VOL
0.1
1
10
±2 ±4 ±6 ±8 ±10 ±12 ±14 ±16 ±18
SUPPLY VOLTAGE [V]
LOAD RESISTANCE [k
]
Ω
Fig.7
Fig.6
Maximum Output Voltage
- Supply Voltage
Maximum Output Voltage
- Load Resistance
(RL=2kΩ,Ta=25℃)
(VCC/VEE=+15V/-15V,Ta=25℃)
20
15
10
5
20
15
10
5
VOH
VOH
0
0
-5
-5
VOL
VOL
-10
-15
-20
-10
-15
-20
-50
-25
0
25
50
75
100
0
5
10
15
20
25
AMBIENT TEMPERATURE [
]
OUTPUT CURRENT [mA]
℃
Fig.9
Fig.8
Maximum Output Voltage
- Output Current
Maximum Output Voltage
- Ambient Temperature
(VCC/VEE=+15V/-15V,Ta=25℃)
(VCC/VEE=+15V/-15V, RL=2kΩ)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
11/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560
6
4
6
4
-40℃
25℃
±4V
±7.5V
2
2
0
0
±15V
-2
-4
-6
-2
-4
-6
85℃
±2
±4
±6
±8
±10 ±12 ±14 ±16
-50
-25
0
25
50
75
100
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [
]
℃
Fig.10
Fig.11
Input Offset Voltage - Supply Voltage
(Vicm=0V, Vout=0V)
Input Offset Voltage - Ambient Temperature
(Vicm=0V, Vout=0V)
60
50
40
30
20
10
0
80
70
60
50
40
30
20
10
0
±4V
-40℃
25℃
±7.5V
±15V
85℃
-50
-25
0
25
50
75
100
±0 ±2 ±4 ±6 ±8 ±10 ±12 ±14 ±16
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [
]
℃
Fig.12
Fig.13
Input Bias Current - Supply Voltage
(Vicm=0V, Vout=0V)
Input Bias Current - Ambient Temperature
(Vicm=0V, Vout=0V)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
12/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560
30
30
20
10
0
20
10
-40℃
25℃
±4V
±7.5V
0
±15V
-10
-20
-30
-10
-20
-30
85℃
-50
-25
0
25
50
75
100
±0 ±2 ±4 ±6 ±8 ±10 ±12 ±14 ±16
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [°C]
Fig.15
Fig.14
Input Offset Current - Ambient Temperature
(Vicm=0V, Vout=0V)
Input Offset Current - Supply Voltage
(Vicm=0V, Vout=0V)
5
4
150
125
100
75
85℃
3
25℃
2
-40℃
1
0
-1
-2
-3
-4
-5
50
25
0
-50
-25
0
25
50
75
100
0
2
4
6
8
AMBIENT TEMPERATURE [°C]
COMMON MODE INPUT VOLTAGE [V]
Fig.17
Fig.16
Common Mode Rejection Ratio
- Ambient Temperature
(VCC/VEE=+15V/-15V, Vicm=-12V to +12V)
Input Offset Voltage
-Common Mode Input Voltage
(VCC=8V, Vout=4V)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
13/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560
150
125
100
75
6
5
4
3
2
1
0
50
25
0
±2
±4
±6
±8
±10 ±12 ±14 ±16
-50
-25
0
25
50
75
100
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [
]
℃
Fig.19
Fig.18
Slew Rate - Supply Voltage (CL=100pF,
Power Supply Rejection Ratio
- Ambient Temperature
RL=2kΩ, Ta=25℃)
(VCC/VEE=+4V/-4V to +15V/-15V)
80
60
40
20
0
1
0.1
0.01
20kHz
1kHz
0.001
0.0001
20Hz
0.1
1
10
1
10
100
1000
10000
OUTPUT VOLTAGE [Vrms]
FREQUENCY [Hz]
Fig.20
Fig.21
Equivalent Input Noise Voltage - Frequency
(VCC/VEE=+15V/-15V, RS=100Ω, Ta=25℃)
Total Harmonic Distortion - Output Voltage
(VCC/VEE=+15V/-15V, AV=20dB,
RL=2kΩ, 80kHz-LPF, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
14/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560
50
200
180
160
140
120
100
80
30
25
20
15
10
5
PHASE
40
30
20
10
0
GAIN
.
60
40
20
0
0
102
103
104
105
106
107
3
4
5
6
SUPPLY VOLTAGE [V]
10
10
10
10
FREQUENCY [KHz]
Fig.22
Fig.23
Maximum Output Voltage Swing – Frequency
(VCC/VEE=+15V/-15V, RL=2kΩ, Ta=25℃)
Voltage Gain - Frequency
(VCC/VEE=+15V/-15V, AV=40dB, RL=2kΩ, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
15/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560R
1000
800
600
400
200
0
5.0
4.0
3.0
2.0
1.0
0.0
-40℃
25℃
BA4560RF
BA4560RFJ
BA4560RFV/FVT
BA4560RFVM
105℃
0
5
10
15
20
25
30
35
0
25
50
75
100
125
SUPPLY VOLTAGE [V]
℃
]
AMBIENT TEMPERTURE [
.
Fig.25
Fig.24
Derating Curve
Supply Current - Supply Voltage
5.0
4.0
3.0
2.0
1.0
0.0
30
±15V
25
20
15
10
5
±4 V
±7.5 V
0
-50 -25
0
25
50
75 100 125
0.1
1
LOAD RESISTANCE [k
10
AMBIENT TEMPERATURE [
]
℃
]
Ω
Fig.27
Fig.26
Maximum Output Voltage Swing
- Load Resistance
Supply Current - Ambient Temperature
(VCC/VEE=+15V/-15V, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
16/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560R
20
20
15
10
5
15
10
5
VOH
VOH
0
0
-5
-5
VOL
-10
-15
-20
-10
-15
-20
VOL
0.1
1
10
±4
±6
±8
±10
±12
±14
±16
SUPPLY VOLTAGE [V]
LOAD RESISTANCE [k ]
Ω
Fig.28
Fig.29
Maximum Output Voltage
- Load Resistance
Maximum Output Voltage
- Supply Voltage
(VCC/VEE=+15V/-15V, Ta=25℃)
(RL=2kΩ, Ta=25℃)
20
15
10
5
20
15
10
5
VOH
VOH
0
0
-5
-5
VOL
VOL
-10
-15
-20
-10
-15
-20
0
5
10
15
20
25
-50 -25
0
25
50
75 100 125
OUTPUT CURRENT [mA]
AMBIENT TEMPERATURE [
]
℃
Fig.31
Fig.30
Maximum Output Voltage
- Output Current
Maximum Output Voltage
- Ambient Temperature
(VCC/VEE=+15V/-15V, Ta=25℃)
(VCC/VEE=+15V/-15V, RL=2kΩ)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
17/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560R
6
4
6
4
±4V
2
2
-40℃
±7.5V
25℃
0
0
105℃
-2
-4
-6
-2
-4
-6
±15V
-50 -25
0
25
50
75 100 125
±2
±4
±6
±8 ±10 ±12 ±14 ±16
AMBIENT TEMPERATURE [
]
SUPPLY VOLTAGE [V]
℃
Fig.33
Fig.32
Input Offset Voltage - Ambient Temperature
(Vicm=0V, Vout=0V)
Input Offset Voltage - Supply Voltage
(Vicm=0V, Vout=0V)
200
180
160
140
120
100
80
200
180
160
140
120
100
80
±4V
±7.5V
25℃
-40℃
60
60
40
40
105℃
±15V
20
20
0
0
±2
±4
±6
±8 ±10 ±12 ±14 ±16
±2
±4
±6
±8 ±10 ±12 ±14 ±16
SUPPLY VOLTAGE [V]
SUPPLY VOLTAGE [V]
Fig.35
Fig.34
Input Bias Current - Ambient Temperature
(Vicm=0V, Vout=0V)
Input Bias Current - Supply Voltage
(Vicm=0V, Vout=0V)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
18/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560R
60
60
40
40
20
-40℃
105℃
±4V
20
±15V
0
0
±7.5V
-20
-40
-60
-20
-40
-60
25℃
-50 -25
0
25
50
75
100 125
±0 ±2 ±4 ±6 ±8 ±10 ±12 ±14 ±16
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [°C]
Fig.36
Fig.37
Input Offset Current - Supply Voltage
(Vicm=0V, Vout=0V)
Input Offset Current - Ambient Temperature
(Vicm=0V, Vout=0V)
150
125
100
75
5
4
3
2
1
0
-1
-2
-3
-4
-5
-40℃
50
25℃
25
105℃
0
-50 -25
0
25
50
75 100 125
0
2
4
6
8
AMBIENT TEMPERATURE [°C]
COMMON MODE INPUT VOLTAGE [V]
Fig.39
Fig.38
Input Offset Voltage
-Common Mode Input Voltage
(VCC=8V, Vout=4V)
Common Mode Rejection Ratio
- Ambient Temperature
(VCC/VEE=+15V/-15V, Vicm=-12V to +12V)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
19/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560R
5.0
150
125
100
75
4.0
3.0
2.0
1.0
0.0
50
25
0
-50 -25
0
25
50
75
100 125
±2
±4
±6
±8
±10 ±12 ±14 ±16
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [
]
℃
Fig.41
Fig.40
Slew Rate - Supply Voltage
(CL=100pF, RL=2kΩ, Ta=25℃)
Power Supply Rejection Ratio
- Ambient Temperature
(VCC/VEE=+4V/-4V to +15V/-15V)
1
0.1
80
60
40
20
0
20kHz
0.01
1kHz
0.001
20Hz
0.0001
0.1
1
10
1
10
100
1000
10000
OUTPUT VOLTAGE [Vrms]
FREQUENCY [Hz]
Fig.43
Fig.42
Total Harmonic Distortion - Output Voltage
(VCC/VEE=+15V/-15V, AV=20dB,
RL=2kΩ, 80kHz-LPF, Ta=25℃)
Equivalent Input Noise Voltage - Frequency
(VCC/VEE=+15V/-15V, RS=100Ω, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
20/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4560R
60
0
30
25
20
15
10
5
50
40
30
20
10
0
-30
PHASE
-60
-90
GAIN
-120
-150
-180
0
246
3
5
7
2
3
4
5
6
10 10 10 10 10 10
10
10
10 10 10 10
FREQUENCY [Hz]
Fig.45
FREQUENCY [Hz]
Fig.44
Voltage Gain - Frequency (VCC/VEE=+15V/-15V,
Maximum Output Voltage Swing - Frequency
(VCC/VEE=+15V/-15V, RL=2kΩ, Ta=25℃)
AV=40dB, RL=2kΩ, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
21/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564R
12.0
1000
800
600
400
200
0
10.0
8.0
6.0
4.0
2.0
0.0
-40℃
BA4564RFV
25℃
105℃
0
25
50
75
100
125
0
5
10
15
20
25
30
35
℃
]
AMBIENT TEMPERATURE [
SUPPLY VOLTAGE [V]
Fig.46
Derating Curve
Fig.47
Supply Current - Supply Voltage
30
12.0
10.0
8.0
25
20
15
10
5
±15V
6.0
±4V
4.0
±7.5V
2.0
0.0
0
-50 -25
0
25
50
75 100 125
0.1
1
LOAD RESISTANCE [k
10
AMBIENT TEMPERATURE [
]
℃
]
Ω
Fig.49
Fig.48
Maximum Output Voltage Swing
- Load Resistance
Supply Current - Ambient Temperature
(VCC/VEE=+15V/-15V, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
22/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564R
20
20
15
10
5
15
10
5
VOH
VOH
0
0
-5
-5
VOL
-10
-15
-20
-10
-15
-20
VOL
±4
±6
±8
±10
±12
±14
±16
0.1
1
10
SUPPLY VOLTAGE [V]
LOAD RESISTANCE [k ]
Ω
Fig.50
Fig.51
Maximum Output Voltage
-Load Resistance
Maximum Output Voltage
-Supply Voltage
(VCC/VEE=+15V/-15V, Ta=25℃)
(RL=2kΩ, Ta=25℃)
20
15
10
5
20
15
10
5
VOH
VOH
0
0
-5
-5
VOL
VOL
-10
-15
-20
-10
-15
-20
-50 -25
0
25
50
75 100 125
0
5
10
15
20
25
AMBIENT TEMPERATURE [
]
℃
OUTPUT CURRENT [mA]
Fig.52
Fig.53
Maximum Output Voltage
- Ambient Temperature
(VCC/VEE=+15V/-15V, RL=2kΩ)
Maximum Output Voltage
- Output Current
(VCC/VEE=+15V/-15V,Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
23/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564R
6
6
4
4
2
±4V
-40℃
±7.5V
25℃
2
0
0
105℃
±15V
-2
-4
-6
-2
-4
-6
-50 -25
0
25
50
75 100 125
±2
±4
±6
±8 ±10 ±12 ±14 ±16
AMBIENT TEMPERATURE [
]
SUPPLY VOLTAGE [V]
℃
Fig.54
Fig.55
Input Offset Voltage - Supply Voltage
(Vicm=0V, Vout=0V)
Input Offset Voltage - Ambient Temperature
(Vicm=0V, Vout=0V)
200
180
160
140
120
100
80
200
180
160
140
120
100
80
-40℃
25℃
±7.5V
±4V
60
60
±15V
105℃
40
40
20
20
0
0
±2
±4
±6
±8 ±10 ±12 ±14 ±16
-50 -25
0
25
50
75 100 125
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [
]
℃
Fig.56
Fig.57
Input Bias Current - Supply Voltage
(Vicm=0V, Vout=0V)
Input Bias Current - Ambient Temperature
(Vicm=0V, Vout=0V)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
24/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564R
60
60
40
40
20
-40℃
±4V
105℃
20
±15V
0
0
±7.5V
-20
-40
-60
-20
-40
-60
25℃
±0 ±2 ±4 ±6 ±8 ±10 ±12 ±14 ±16
SUPPLY VOLTAGE [V]
-50 -25
0
25
50
75
100 125
AMBIENT TEMPERATURE [°C]
Fig.58
Fig.59
Input Offset Current - Supply Voltage
(Vicm=0V, Vout=0V)
Input Offset Current - Ambient Temperature
(Vicm=0V, Vout=0V)
150
125
100
75
5
4
3
-40℃
25℃
2
105℃
1
0
-1
-2
-3
-4
-5
50
25
0
-50 -25
0
25
50
75 100 125
0
2
4
6
8
AMBIENT TEMPERATURE [°C]
COMMON MODE INPUT VOLTAGE [V]
Fig.61
Fig.60
Input Offset Voltage
- Common Mode Input Voltage
(VCC=8V, Vout=4V)
Common Mode Rejection Ratio
- Ambient Temperature
(VCC/VEE=+15V/-15V, Vicm=-12V to +12V)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
25/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564R
150
125
100
75
5.0
4.0
3.0
2.0
1.0
0.0
50
25
0
-50 -25
0
25
50
75
100 125
±2
±4
±6
±8
±10 ±12 ±14 ±16
AMBIENT TEMPERATURE [
]
℃
SUPPLY VOLTAGE [V]
Fig.63
Fig.62
Slew Rate - Supply Voltage
(CL=100pF, RL=2kΩ, Ta=25℃)
Power Supply Rejection Ratio
- Ambient Temperature
(VCC/VEE=+4V/-4V to +15V/-15V)
80
60
40
20
0
1
0.1
0.01
20kHz
1kHz
0.001
0.0001
20Hz
0.1
1
10
1
10
100
1000
10000
OUTPUT VOLTAGE [Vrms]
FREQUENCY [Hz]
Fig.64
Fig.65
Equivalent Input Noise Voltage - Frequency
(VCC/VEE=+15V/-15V, RS=100Ω, Ta=25℃)
Total Harmonic Distortion - Output Voltage
(VCC/VEE=+15V/-15V, AV=20dB,
RL=2kΩ, 80kHz-LPF, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
26/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564R
30
25
20
15
10
5
60
50
40
30
20
10
0
-200
-170
-140
-110
-80
PHASE
GAIN
-50
-20
0
102
103
104
105
106
107
456
2
3
FREQUENCY [Hz]
10
10
10
10
10
10
FREQUENCY [Hz]
Fig.66
Fig.67
Maximum Output Voltage Swing – Frequency
(VCC/VEE=+15V/-15V, RL=2kΩ, Ta=25℃)
Voltage Gain - Frequency
(VCC/VEE=+15V/-15V, AV=40dB, RL=2kΩ, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
27/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564W
12.0
1000
800
600
400
200
0
10.0
8.0
6.0
4.0
2.0
0.0
BA4564WFV
-40℃
25℃
105℃
0
25
50
75
100
125
0
5
10
15
20
25
30
35
℃
]
AMBIENT TEMPERATURE [
SUPPLY VOLTAGE [V]
Fig.68
Derating Curve
Fig.69
Supply Current - Supply Voltage
30
12.0
10.0
8.0
25
20
15
10
5
±15V
6.0
±4V
4.0
±7.5V
2.0
0.0
0
-50 -25
0
25
50
75 100 125
0.1
1
10
AMBIENT TEMPERATURE [
]
℃
LOAD RESISTANCE [k ]
Ω
Fig.71
Fig.70
Maximum Output Voltage Swing
- Load Resistance
Supply Current - Ambient Temperature
(VCC/VEE=+15V/-15V, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
28/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564W
20
20
15
10
5
15
10
5
VOH
VOH
0
0
-5
-5
VOL
-10
-15
-20
-10
-15
-20
VOL
0.1
1
10
±4
±6
±8
±10
±12
±14
±16
LOAD RESISTANCE [kΩ]
SUPPLY VOLTAGE [V]
Fig.72
Fig.73
Maximum Output Voltage
-Load Resistance
Maximum Output Voltage
-Supply Voltage
(VCC/VEE=+15V/-15V, Ta=25℃)
(RL=2kΩ, Ta=25℃)
20
15
10
5
20
15
10
5
VOH
VOH
0
0
-5
-5
VOL
VOL
-10
-15
-20
-10
-15
-20
-50 -25
0
25
50
75 100 125
0
5
10
15
20
25
AMBIENT TEMPERATURE [
]
℃
OUTPUT CURRENT [mA]
Fig.74
Fig.75
Maximum Output Voltage
- Ambient Temperature
(VCC/VEE=+15V/-15V, RL=2kΩ)
Maximum Output Voltage
- Output Current
(VCC/VEE=+15V/-15V, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
29/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564W
6
6
4
4
2
±4V
-40℃
±7.5V
25℃
2
0
0
105℃
±15V
-2
-4
-6
-2
-4
-6
-50 -25
0
25
50
75 100 125
±2
±4
±6
±8 ±10 ±12 ±14 ±16
AMBIENT TEMPERATURE [
]
SUPPLY VOLTAGE [V]
℃
Fig.76
Fig.77
Input Offset Voltage - Supply Voltage
(Vicm=0V, Vout=0V)
Input Offset Voltage - Ambient Temperature
(Vicm=0V, Vout=0V)
200
180
160
140
120
100
80
200
180
160
140
120
100
80
-40℃
25℃
±7.5V
±4V
60
60
±15V
105℃
40
40
20
20
0
0
±2
±4
±6
±8 ±10 ±12 ±14 ±16
-50 -25
0
25
50
75 100 125
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [
]
℃
Fig.78
Fig.79
Input Bias Current - Supply Voltage
(Vicm=0V, Vout=0V)
Input Bias Current - Ambient Temperature
(Vicm=0V, Vout=0V)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
30/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564W
60
60
40
40
20
-40℃
±4V
105℃
20
±15V
0
0
±7.5V
-20
-40
-60
-20
-40
-60
25℃
±0 ±2 ±4 ±6 ±8 ±10 ±12 ±14 ±16
SUPPLY VOLTAGE [V]
-50 -25
0
25
50
75
100 125
AMBIENT TEMPERATURE [°C]
Fig.80
Fig.81
Input Offset Current - Supply Voltage
(Vicm=0V, Vout=0V)
Input Offset Current - Ambient Temperature
(Vicm=0V, Vout=0V)
150
125
100
75
5
4
3
-40℃
25℃
2
105℃
1
0
-1
-2
-3
-4
-5
50
25
0
-50 -25
0
25
50
75 100 125
0
2
4
6
8
AMBIENT TEMPERATURE [°C]
COMMON MODE INPUT VOLTAGE [V]
Fig.83
Fig.82
Input Offset Voltage
- Common Mode Input Voltage
(VCC=8V, Vout=4V)
Common Mode Rejection Ratio
- Ambient Temperature
(VCC/VEE=+15V/-15V, Vicm=-12V to +12V)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
31/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564W
150
125
100
75
5.0
4.0
3.0
2.0
1.0
0.0
50
25
0
-50 -25
0
25
50
75
100 125
±2
±4
±6
±8
±10 ±12 ±14 ±16
AMBIENT TEMPERATURE [
]
℃
SUPPLY VOLTAGE [V]
Fig.85
Fig.84
Slew Rate - Supply Voltage
(CL=100pF, RL=2kΩ, Ta=25℃)
Power Supply Rejection Ratio
- Ambient Temperature
(VCC/VEE=+4V/-4V to +15V/-15V)
80
60
40
20
0
1
0.1
0.01
20kHz
1kHz
0.001
0.0001
20Hz
0.1
1
10
1
10
100
1000
10000
OUTPUT VOLTAGE [Vrms]
FREQUENCY [Hz]
Fig.86
Fig.87
Equivalent Input Noise Voltage - Frequency
(VCC/VEE=+15V/-15V,RS=100Ω, Ta=25℃)
Total Harmonic Distortion - Output Voltage
(VCC/VEE=+15V/-15V, AV=20dB,
RL=2kΩ,80kHz-LPF, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
32/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
○BA4564W
30
25
20
15
10
5
60
-200
-170
-140
-110
-80
PHASE
50
40
30
20
10
0
GAIN
-50
-20
0
2
3
4
5
6
7
456
2
3
1
10
10
10 10
10
10
10
10
10
10
10
10
FREQUENCY [Hz]
FREQUENCY [Hz]
Fig.88
Fig.89
Maximum Output Voltage Swing – Frequency
(VCC/VEE=+15V/-15V, RL=2kΩ,Ta=25℃)
Voltage Gain - Frequency
(VCC/VEE=+15V/-15V, AV=40dB, RL=2kΩ, Ta=25℃)
(*)The above data is measurement value of typical sample, it is not guaranteed.
www.rohm.com
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
© 2012 ROHM Co., Ltd. All rights reserved.
33/41
TSZ22111･15･00
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
●Application Information
Test circuit1 NULL method
VCC, VEE, EK, Vicm Unit: V
Parameter
VF
S1
S2
S3
VCC
VEE
EK
Vicm
calculation
Input Offset Voltage
VF1
VF2
ON
ON
OFF
OFF
OFF
ON
15
15
15
-15
-15
-15
0
0
0
0
1
2
3
4
5
6
Input Offset Current
Input Bias Current
OFF
OFF
VF3
VF4
VF5
VF6
VF7
VF8
VF9
VF10
OFF
ON
ON
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
OFF
15
15
3
-15
-15
-27
-3
Large Signal Voltage Gain
ON
ON
ON
ON
ON
ON
Common-mode Rejection Ratio
OFF
OFF
(Input common-mode Voltage Range)
27
4
-4
Power Supply
Rejection Ratio
15
-15
-Calculation-
1. Input Offset Voltage (Vio)
VF1
Vio
[V]
1+Rf / Rs
0.1μF
Rf=50kΩ
2. Input Offset Current (Iio)
VF2- VF1
0.1μF
500kΩ
Iio
[A]
VCC
DUT
EK
Ri×(1+Rf / Rs)
SW1
+15V
Rs=50Ω
500kΩ
1000pF
3. Input Bias Current (Ib)
Ri=10kΩ
Ri=10kΩ
VF4- VF3
Ib
NULL
SW3
[A]
Rs=50Ω
V
VF
2×Ri×(1+Rf / Rs)
Vicm
RL
SW2
VEE
50kΩ
-15V
4. Large Signal Voltage Gain (Av)
ΔEK×(1+Rf/Rs)
Av 20×Log
[dB]
Fig. 90 Test circuit1 (one channel only)
VF5- VF6
5. Common-mode Rejection Ration (CMRR)
ΔVicm×(1+Rf/Rs)
CMRR 20×Log
[dB]
VF8 - VF7
6. Power supply rejection ratio (PSRR)
ΔVcc×(1+Rf/Rs)
PSRR 20×Log
[dB]
VF10 - VF9
Test Circuit 2 Switch Condition
SW No.
Supply Current
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 SW11 SW12 SW13 SW14
OFF OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF OFF
OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF
OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF
OFF OFF OFF ON OFF OFF OFF ON ON ON OFF OFF OFF OFF
OFF ON OFF OFF ON ON OFF OFF ON ON ON OFF OFF OFF
ON OFF OFF OFF ON OFF ON OFF ON ON ON OFF OFF OFF
ON OFF OFF OFF ON ON OFF OFF OFF OFF ON OFF OFF OFF
High Level Output Voltage
Low Level Output Voltage
Slew Rate
Unity Gain Frequency
Total Harmonic Distortion
Input Referred Noise Voltage
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
34/41
7.SEP.2012 Rev.002
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
Input voltage
VH
SW4
R2
SW5
VCC
A
VL
－
t
Input wave
＋
SW1
RS
SW2
SW3
Output voltage
VH
SW6
VIN-
SW7
VIN+
SW8
SW9 SW10 SW11 SW12 SW13 SW14
R1
C
SR=ΔV/Δt
90%
VEE
A
RL
CL
V
～
～
V
ΔV
～
VOUT
10%
VL
Δt
Output wave
t
Fig.91 Test Circuit 2 (each Op-Amp)
Fig. 92 Slew Rate Input Waveform
Test Circuit 3 Channel Separation
VCC
VCC
OTHER
CH
R1//R2
R1//R2
VEE
VEE
R1
R2
R1
R2
VOUT1
=0.5[Vrms]
V
V
VOUT2
VIN
100 VOUT1
×
CS 20 log
＝
×
VOUT2
Fig. 93 Test circuit 3
(VCC=+15V, VEE=-15V, R1=1kΩ, R2=100kΩ)
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
35/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
●Power Dissipation
Power dissipation(total loss) indicates the power that can be consumed by IC at Ta=25℃(normal temperature). IC is heated
when it consumed power, and the temperature of IC chip becomes higher than ambient temperature. The temperature that
can be accepted by IC chip depends on circuit configuration, manufacturing process, and consumable power is limited.
Power dissipation is determined by the temperature allowed in IC chip(maximum junction temperature) and thermal
resistance of package(heat dissipation capability). The maximum junction temperature is typically equal to the maximum
value in the storage temperature range. Heat generated by consumed power of IC radiates from the mold resin or lead
frame of the package. The parameter which indicates this heat dissipation capability(hardness of heat release)is called
thermal resistance, represented by the symbol θja℃/W. The temperature of IC inside the package can be estimated by this
thermal resistance. Fig.94(a) shows the model of thermal resistance of the package. Thermal resistance θja, ambient
temperature Ta, junction temperature Tj, and power dissipation Pd can be calculated by the equation below:
θja = (Tjmax-Ta) / Pd
℃/W
・・・・・ (Ⅰ)
Derating curve in Fig.94 (b) indicates power that can be consumed by IC with reference to ambient temperature. Power that
can be consumed by IC with reference to ambient temperature. Power that can be consumed by IC begins to attenuate at
certain ambient temperature. This gradient is determined by thermal resistance θja. Thermal resistance θja depends on
chip size, power consumption, package, ambient temperature, package condition, wind velocity, etc even when the same of
package is used. Thermal reduction curve indicates a reference value measured at a specified condition. Fig.95(c), to , (e)
show a derating curve for an example of BA4560, BA4560R, BA4564R, BA4564W.
Power dissipation of LSI [W]
Pd (max)
θja=(Tjmax-Ta)/Pd ℃/W
P2
θja2 < θja1
θ' ja2
Ambient temperature Ta [℃]
P1
θ ja2
Tj ' (max) Tj (max)
θ' ja1
θ ja1
Chip surface temperature Tj [℃]
0
25
50
75
100
125
150
Power dissipation P [W]
Ambient temperature Ta [℃]
(a) Thermal resistance
(b) Derating curve
Fig. 94Thermal resistance and derating curve
1000
1000
800
600
400
200
0
1000
800
600
400
200
0
BA4560F(*16)
800
BA4564RFV/WFV(*20)
BA4560FJ(*17)
BA4560F(*16)
BA4560FV/FVT(*18)
600
BA4560FJ(*17)
BA4560FV/FVT(*18)
BA4560FVM(*19)
BA4560FVM(*19)
400
200
0
0
25
50
75
100
℃
125
0
25
50
75
100
125
0
25
50
75
100
125
AMBIENT TEMPERATURE [
]
℃
AMBIEN T TEMPERT URE [
]
.
AMBIENT TEMPERTURE [
]
℃
.
(c)BA4560
(d)BA4560R
(e)BA4564R/BA4564W
(*18)
5
(*16)
5.52
(*17)
5.4
(*19)
4.7
(*20)
7
Unit
mW/℃
When using the unit above Ta=25℃, subtract the value above per degree℃. Permissible dissipation is the value.
Permissible dissipation is the value when FR4 glass epoxy board 70mm ×70mm ×1.6mm (cooper foil area below 3%) is mounted.
Fig. 95 Derating curve
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
36/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
Examples of circuit
○Voltage follower
Voltage gain is 0 dB.
This circuit controls output voltage (Vout) equal input
voltage (Vin), and keeps Vout with stable because of
high input impedance and low output impedance.
Vout is shown next formula.
VCC
Vout=Vin
Vout
Vin
VEE
Fig. 96 Voltage follower circuit
○Inverting amplifier
R2
For inverting amplifier, Vi(b) Derating curve voltage
gain decided R1 and R2, and phase reversed voltage
is outputted.
VCC
Vout is shown next formula.
Vout=-(R2/R1)・Vin
Input impedance is R1.
R1
Vin
Vout
R1//R2
VEE
Fig. 97 Inverting amplifier circuit
○Non-inverting amplifier
R1
R2
For non-inverting amplifier, Vin is amplified by voltage
gain decided R1 and R2, and phase is same with Vin.
Vout is shown next formula.
VCC
Vout=(1 + R2/R1)・Vin
This circuit realizes high input impedance because
Input impedance is operational amplifier’s input
Impedance.
Vout
Vin
VEE
Fig. 98 Non-inverting amplifier circuit
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
37/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
VCC
●Operational Notes
1) Processing of unused circuit
+
-
It is recommended to apply connection (see the Fig.99) and set the non inverting
input terminal at the potential within input common-mode voltage range (Vicm),
for any unused circuit.
Connect
to Vicm
Vicm
2) Input voltage
VEE
Applying (VEE - 0.3) to (VEE + 36)V
BA4560R, 4564R, BA4564W)to the input terminal is possible without causing
deterioration of the electrical characteristics or destruction, irrespective of the
supply voltage. However, this does not ensure normal circuit operation. Please
note that the circuit operates normally only when the input voltage is within the
common mode input voltage range of the electric characteristics.
Fig. 99 The example of
application circuit for unused op-amp
VCC
protection
3) Maximum output voltage
resistor
+
Because the output voltage range becomes narrow as the output current
Increases, design the application with margin by considering changes in
electrical characteristics and temperature characteristics.
-
4) Short-circuit of output terminal
VEE
When output terminal and VCC or VEE terminal are shorted, excessive Output
current may flow under some conditions, and heating may destroy IC. It is
necessary to connect a resistor as shown in Fig.100, thereby protecting against
load shorting.
5) Power supply (split supply / single supply) in used
Op-amp operates when specified voltage is applied between VCC and VEE.
Therefore, the single supply Op-Amp can be used for double supply Op-Amp as well.
Fig. 100 The example of
output short protection
6) Power dissipation (Pd)
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating
conditions.
7) Short-circuit between pins and wrong mounting
Pay attention to the assembly direction of the ICs. Wrong mounting direction or shorts between terminals, GND, or other
components on the circuits, can damage the IC.
8) Use in strong electromagnetic field
Using the ICs in strong electromagnetic field can cause operation malfunction.
9) Radiation
This IC is not designed to be radiation-resistant.
10) IC Handling
When stress is applied to IC because of deflection or bend of board, the characteristics may fluctuate due to piezoelectric
(piezo) effect.
11) Inspection on set board
During testing, turn on or off the power before mounting or dismounting the board from the test Jig. Do not power up the
board without waiting for the output capacitors to discharge. The capacitors in the low output impedance terminal can
stress the device. Pay attention to the electro static voltages during IC handling, transportation, and storage.
12) Output capacitor
When VCC terminal is shorted to VEE (GND) potential and an electric charge has accumulated on the external capacitor,
connected to output terminal, accumulated charge may be discharged VCC terminal via the parasitic element within the
circuit or terminal protection element. The element in the circuit may be damaged (thermal destruction). When using this IC
for an application circuit where there is oscillation, output capacitor load does not occur, as when using this IC as a
voltage comparator. Set the capacitor connected to output terminal below 0.1μF in order to prevent damage to IC.
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a reference
to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
38/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
●Physical Dimensions Tape and Reel Information
SOP8
<Tape and Reel information>
5.0± 0.2
(MAX 5.35 include BURR)
Tape
Embossed carrier tape
2500pcs
+
−
6
°
4°
4
°
Quantity
8
1
7
6
5
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
2
3
4
0.595
+0.1
0.17
-
0.05
S
0.1
S
1.27
Direction of feed
1pin
0.42± 0.1
Reel
Order quantity needs to be multiple of the minimum quantity.
(Unit : mm)
∗
SSOP-B8
<Tape and Reel information>
3.0± 0.2
(MAX 3.35 include BURR)
8
7
6
5
Tape
Embossed carrier tape
Quantity
2500pcs
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1
2
3
4
0.15± 0.1
S
M
0.1
S
Direction of feed
1pin
+0.06
−0.04
(0.52)
0.65
0.22
0.08
Reel
(Unit : mm)
Order quantity needs to be multiple of the minimum quantity.
∗
SOP-J8
<Tape and Reel information>
4.9± 0.2
(MAX 5.25 include BURR)
Tape
Embossed carrier tape
+
6°
4°
−4°
Quantity
2500pcs
8
7
6
5
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1
2
3
4
0.545
0.2± 0.1
S
1.27
0.42± 0.1
0.1
Direction of feed
1pin
S
Reel
(Unit : mm)
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
39/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
MSOP8
<Tape and Reel information>
2.9± 0.1
Tape
Embossed carrier tape
3000pcs
(MAX 3.25 include BURR)
+
6°
4°
Quantity
−4°
8
7
6
5
TR
Direction
of feed
The direction is the 1pin of product is at the upper right when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1
2
3
4
1PIN MARK
+0.05
1pin
+0.05
−0.03
0.145
0.475
S
0.22
−0.04
0.08
S
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
0.65
Reel
(Unit : mm)
∗
TSSOP-B8
<Tape and Reel information>
3.0± 0.1
(MAX 3.35 include BURR)
Tape
Embossed carrier tape
4 ± ±4
8
7
6
5
Quantity
3000pcs
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1
2
3
4
1PIN MARK
+0.05
0.145
−0.03
0.525
S
0.08 S
+0.05
0.245
M
−0.04
0.08
Direction of feed
1pin
0.65
Reel
(Unit : mm)
Order quantity needs to be multiple of the minimum quantity.
∗
SSOP-B14
<Tape and Reel information>
5.0 ± 0.2
Tape
Embossed carrier tape
14
8
Quantity
2500pcs
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1
7
0.15 ± 0.1
0.1
0.65
Direction of feed
1pin
0.22 ± 0.1
Reel
(Unit : mm)
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
40/41
BA4560xxx, BA4560Rxxx, BA4564RFV, BA4564WFV
Datasheet
●Marking Diagrams
SOP8(TOP VIEW)
SSOP-B8(TOP VIEW)
Part Number Marking
LOT Number
Part Number Marking
LOT Number
1PIN MARK
1PIN MARK
MSOP8(TOP VIEW)
TSSOP-B8(TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
SOP-J8(TOP VIEW)
SSOP-B14(TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
LOT Number
1PIN MARK
1PIN MARK
Product Name
Package Type
Marking
4560
F
SOP8
FJ
SOP-J8
FV
BA4560
SSOP-B8
TSSOP-B8
MSOP8
FVT
FVM
FJ
SOP-J8
F
SOP8
FJ
SOP-J8
FV
SSOP-B8
TSSOP-B8
MSOP8
BA4560R
4560R
FVT
FVM
FJ
SOP-J8
BA4564R
BA4564W
FV
FV
SSOP-B14
SSOP-B14
4564R
4564W
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･00
TSZ02201-0RAR1G200020-1-2
7.SEP.2012 Rev.002
41/41
Daattaasshheeeett
Notice
●General Precaution
1) Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2) All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
●Precaution on using ROHM Products
1) Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
2) ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3) Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4) The Products are not subject to radiation-proof design.
5) Please verify and confirm characteristics of the final or mounted products in using the Products.
6) In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7) De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8) Confirm that operation temperature is within the specified range described in the product specification.
9) ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
●Precaution for Mounting / Circuit board design
1) When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2) In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
●Precautions Regarding Application Examples and External Circuits
1) If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2) You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
●Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
●Precaution for Storage / Transportation
1) Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2) Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3) Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4) Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
●Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
●Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
●Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
●Precaution Regarding Intellectual Property Rights
1) All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2) No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
●Other Precaution
1) The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
2) This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
3) The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
4) In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
5) The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - Rev.003
© 2012 ROHM Co., Ltd. All rights reserved.
相关型号：
©2020 ICPDF网 联系我们和版权申明