CY7C1019CV33-10ZXCT [ROCHESTER]
128KX8 STANDARD SRAM, 10ns, PDSO32, LEAD FREE, TSOP2-32;
| 型号： | CY7C1019CV33-10ZXCT |
| 厂家： | 
Rochester Electronics |
| 描述： | 128KX8 STANDARD SRAM, 10ns, PDSO32, LEAD FREE, TSOP2-32 静态存储器 光电二极管 |
| 文件： | 总11页 (文件大小：1048K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CY7C1019CV33
128K x 8 Static RAM
device has an automatic power-down feature that significantly
reduces power consumption when deselected.
Features
• Pin and function compatible with CY7C1019BV33
• High speed
Writing to the device is accomplished by taking Chip Enable
(CE) and Write Enable (WE) inputs LOW. Data on the eight I/O
pins (I/O0 through I/O7) is then written into the location
specified on the address pins (A0 through A16).
— tAA = 10 ns
• CMOS for optimum speed/power
• Data retention at 2.0V
Reading from the device is accomplished by taking Chip
Enable (CE) and Output Enable (OE) LOW while forcing Write
Enable (WE) HIGH. Under these conditions, the contents of
the memory location specified by the address pins will appear
on the I/O pins.
• Center power/ground pinout
• Automatic power-down when deselected
• Easy memory expansion with CE and OE options
The eight input/output pins (I/O0 through I/O7) are placed in a
high-impedance state when the device is deselected (CE
HIGH), the outputs are disabled (OE HIGH), or during a write
operation (CE LOW, and WE LOW).
• Available in Pb-free and non Pb-free 48-ball VFBGA,
32-pin TSOP II and 400-mil SOJ package
Functional Description
The CY7C1019CV33 is available in Standard 48-ball FBGA,
32-pin TSOP II and 400-mil-wide SOJ packages
The CY7C1019CV33 is a high-performance CMOS static
RAM organized as 131,072 words by 8 bits. Easy memory
expansion is provided by an active LOW Chip Enable (CE), an
active LOW Output Enable (OE), and tri-state drivers. This
Logic Block Diagram
Pin Configuration
SOJ/TSOP II
Top View
A
A
1
A
A
32
1
0
16
31
30
2
3
4
5
6
15
A
A
14
A
13
2
I/O
A
29
28
3
0
INPUT BUFFER
CE
OE
I/O
I/O
I/O
27
26
1
I/O
A
0
0
1
7
A
A
2
1
I/O
V
7
8
9
10
11
12
13
6
I/O
2
25
24
23
22
21
V
CC
SS
A
3
V
A
I/O
V
CC
I/O
4
SS
128K x 8
ARRAY
3
A
5
I/O
I/O
2
3
5
4
A
6
I/O
I/O
A
4
A
7
A
8
WE
A
4
12
I/O
A
11
5
20
19
A
5
A
10
14
15
16
I/O
6
POWER
DOWN
A
6
A
9
A
8
COLUMN
DECODER
18
17
CE
A
7
I/O
WE
7
OE
Cypress Semiconductor Corporation
Document #: 38-05130 Rev. *F
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised August 3, 2006
CY7C1019CV33
Pin Configuration[1]
48-ball VFBGA
(Top View)
1
4
2
5
3
6
A
A
A
7
NC
OE
NC
2
6
A
B
C
A
A
I/O NC
CE
NC
NC
NC
I/O
I/O
7
5
1
0
A
A
A
NC
NC
I/O
I/O
0
4
3
1
6
NC
V
CC
V
SS
D
E
F
NC
V
CC
NC
V
SS
NC
NC
A
A
11
I/O
I/O
5
14
4
2
A
A
G
H
I/O
NC
A
WE
A8
12
15
3
A
A
A13
NC
NC
9
16
10
Selection Guide
-10
-12
12
75
5
-15
15
70
5
Unit
ns
Maximum Access Time
10
80
5
Maximum Operating Current
Maximum Standby Current
mA
mA
Note:
1. NC pins are not connected on the die.
Document #: 38-05130 Rev. *F
Page 2 of 10
CY7C1019CV33
Current into Outputs (LOW)......................................... 20 mA
Maximum Ratings
Static Discharge Voltage............................................>2001V
(per MIL-STD-883, Method 3015)
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Latch-up Current......................................................>200 mA
Storage Temperature .................................–65°C to +150°C
Ambient Temperature with
Power Applied.............................................–55°C to +125°C
Operating Range
Ambient
Supply Voltage on VCC to Relative GND[2] .... –0.5V to +4.6V
Range
Commercial
Industrial
Temperature
0°C to +70°C
–40°C to +85°C
VCC
DC Voltage Applied to Outputs
3.3V ± 10%
3.3V ± 10%
in High-Z State[2] ....................................–0.5V to VCC + 0.5V
DC Input Voltage[2].................................–0.5V to VCC + 0.5V
Electrical Characteristics Over the Operating Range
–10
–12
–15
Parameter
Description
Test Conditions
Min.
Max.
Min.
Max.
Min.
Max.
Unit
VOH
Output HIGH Voltage VCC = Min.,
IOH = –4.0 mA
2.4
2.4
2.4
V
VOL
Output LOW Voltage VCC = Min.,
0.4
0.4
0.4
V
I
OL = 8.0 mA
VIH
VIL
IIX
Input HIGH Voltage
Input LOW Voltage[2]
2.0
–0.3
–1
VCC + 0.3
2.0
–0.3
–1
VCC + 0.3
0.8
2.0
–0.3
–1
VCC + 0.3
V
V
0.8
+1
+1
0.8
+1
+1
Input Leakage Current GND < VI < VCC
+1
µA
µA
IOZ
Output Leakage
Current
GND < VI < VCC
Output Disabled
,
–1
–1
+1
–1
ICC
VCC Operating
Supply Current
VCC = Max.,
IOUT = 0 mA,
f = fMAX = 1/tRC
80
15
5
75
15
5
70
15
5
mA
mA
mA
ISB1
Automatic CE
Power-down Current VIN > VIH or
—TTL Inputs
Max. VCC, CE > VIH
VIN < VIL, f = fMAX
ISB2
Automatic CE
Max. VCC
,
Power-down Current CE > VCC – 0.3V,
—CMOS Inputs IN > VCC – 0.3V,
V
or VIN < 0.3V, f = 0
Capacitance[3]
Parameter
Description
Test Conditions
TA = 25°C, f = 1 MHz,
CC = 5.0V
Max.
Unit
CIN
Input Capacitance
Output Capacitance
8
8
pF
pF
V
COUT
Notes:
2. V (min.) = –2.0V for pulse durations of less than 20 ns.
IL
3. Tested initially and after any design or process changes that may affect these parameters.
Document #: 38-05130 Rev. *F
Page 3 of 10
CY7C1019CV33
AC Test Loads and Waveforms[4]
High-Z characteristics:
R 317Ω
ALL INPUT PULSES
R 317Ω
3.0V
3.3V
90%
10%
90%
10%
3.3V
OUTPUT
OUTPUT
GND
R2
30 pF
R2
351Ω
351Ω
5 pF
(b)
Fall Time: 1 V/ns
Rise Time: 1 V/ns
(a)
(c)
Switching Characteristics Over the Operating Range[5]
-10
-12
-15
Parameter
Read Cycle
tRC
Description
Min.
10
3
Max.
Min.
Max.
Min.
Max.
Unit
Read Cycle Time
12
3
15
3
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tAA
Address to Data Valid
10
12
15
tOHA
Data Hold from Address Change
tACE
10
5
12
6
15
7
CE LOW to Data Valid
OE LOW to Data Valid
OE LOW to Low Z
OE HIGH to High Z[6, 7]
CE LOW to Low Z[7]
CE HIGH to High Z[6, 7]
tDOE
tLZOE
0
3
0
0
3
0
0
3
0
tHZOE
tLZCE
5
5
6
6
7
7
tHZCE
[8]
tPU
CE LOW to Power-Up
[8]
tPD
10
12
15
CE HIGH to Power-Down
Write Cycle[9, 10]
tWC
tSCE
tAW
Write Cycle Time
10
8
12
9
15
10
10
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
CE LOW to Write End
Address Set-Up to Write End
Address Hold from Write End
Address Set-Up to Write Start
8
9
tHA
0
0
tSA
0
0
0
tPWE
tSD
7
8
10
8
WE Pulse Width
Data Set-Up to Write End
5
6
tHD
Data Hold from Write End
0
0
0
WE HIGH to Low Z[7]
WE LOW to High Z[6, 7]
tLZWE
3
3
3
tHZWE
5
6
7
Notes:
4. AC characteristics (except High-Z) for all speeds are tested using the Thevenin load shown in Figure (a). High-Z characteristics are tested for all speeds using
the test load shown in Figure (c).
5. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V.
6. t
, t
, and t
are specified with a load capacitance of 5 pF as in part (d) of AC Test Loads. Transition is measured ±500 mV from steady-state voltage.
HZOE HZCE
HZWE
7. At any given temperature and voltage condition, t
is less than t
, t
is less than t
, and t
is less than t
for any given device.
HZCE
LZCE HZOE
LZOE
HZWE
LZWE
8. This parameter is guaranteed by design and is not tested.
9. The internal write time of the memory is defined by the overlap of CE LOW and WE LOW. CE and WE must be LOW to initiate a write, and the transition of
any of these signals can terminate the write. The input data set-up and hold timing should be referenced to the leading edge of the signal that terminates the write.
10. The minimum write cycle time for Write Cycle no. 3 (WE controlled, OE LOW) is the sum of t
and t
.
HZWE
SD
Document #: 38-05130 Rev. *F
Page 4 of 10
CY7C1019CV33
Switching Waveforms
Read Cycle No. 1[11, 12]
t
RC
ADDRESS
t
AA
t
OHA
DATA OUT
PREVIOUS DATA VALID
DATA VALID
Read Cycle No. 2 (OE Controlled)[12, 13]
ADDRESS
CE
t
RC
t
ACE
OE
t
HZOE
t
DOE
t
HZCE
t
LZOE
HIGH
IMPEDANCE
HIGH IMPEDANCE
DATA OUT
DATA VALID
t
LZCE
t
PD
ICC
t
PU
V
CC
50%
50%
SUPPLY
CURRENT
ISB
Write Cycle No. 1 (CE Controlled)[14, 15]
t
WC
ADDRESS
CE
t
SCE
t
SA
t
SCE
t
t
HA
AW
t
PWE
WE
t
t
HD
SD
DATA I/O
DATA VALID
Notes:
11. Device is continuously selected. OE, CE = V .
IL
12. WE is HIGH for read cycle.
13. Address valid prior to or coincident with CE transition LOW.
14. Data I/O is high impedance if OE = V
.
IH
15. If CE goes HIGH simultaneously with WE going HIGH, the output remains in a high-impedance state.
Document #: 38-05130 Rev. *F
Page 5 of 10
CY7C1019CV33
Switching Waveforms (continued)
Write Cycle No. 2 (WE Controlled, OE HIGH During Write)[14, 15]
t
WC
ADDRESS
CE
t
SCE
t
t
HA
AW
t
t
PWE
SA
WE
OE
t
t
SD
HD
DATA VALID
DATA I/O
IN
NOTE 16
t
HZOE
Write Cycle No. 3 (WE Controlled, OE LOW)[15]
t
WC
ADDRESS
CE
t
SCE
t
t
HA
AW
t
SA
t
PWE
WE
t
t
HD
SD
NOTE 16
DATA I/O
DATA VALID
t
t
LZWE
HZWE
Truth Table
I/O0–I/O7
Mode
Power
CE
H
L
OE
WE
X
X
L
High Z
Power-Down
Read
Standby (ISB)
H
Data Out
Data In
High Z
Active (ICC
Active (ICC
Active (ICC
)
)
)
L
X
H
L
Write
L
H
Selected, Outputs Disabled
Note:
16. During this period the I/Os are in the output state and input signals should not be applied.
Document #: 38-05130 Rev. *F
Page 6 of 10
CY7C1019CV33
Ordering Information
Speed
(ns)
Package
Diagram
Operating
Range
Ordering Code
Package Type
10
CY7C1019CV33-10VC
CY7C1019CV33-10ZXC
CY7C1019CV33-10ZXI
CY7C1019CV33-12VC
CY7C1019CV33-12ZC
CY7C1019CV33-12ZXC
CY7C1019CV33-12VI
CY7C1019CV33-12BVXI
CY7C1019CV33-15VC
CY7C1019CV33-15VXC
CY7C1019CV33-15ZXC
CY7C1019CV33-15ZXI
51-85033 32-pin 400-Mil Molded SOJ
51-85095 32-pin TSOP II (Pb-Free)
32-pin TSOP II (Pb-Free)
Commercial
Industrial
12
15
51-85033 32-pin 400-Mil Molded SOJ
51-85095 32-pin TSOP II
Commercial
32-pin TSOP II (Pb-Free)
51-85033 32-pin 400-Mil Molded SOJ
51-85150 48-ball VFBGA (Pb-Free)
51-85033 32-pin 400-Mil Molded SOJ
51-85033 32-pin 400-Mil Molded SOJ (Pb-Free)
51-85095 32-pin TSOP II (Pb-Free)
51-85095 32-pin TSOP II (Pb-Free)
Industrial
Commercial
Industrial
Package Diagrams
32-pin (400-Mil) Molded SOJ (51-85033)
51-85033-*B
Document #: 38-05130 Rev. *F
Page 7 of 10
CY7C1019CV33
Package Diagrams (continued)
32-pin TSOP II (51-85095)
51-85095-**
Document #: 38-05130 Rev. *F
Page 8 of 10
CY7C1019CV33
Package Diagrams (continued)
48-ball VFBGA (6 x 8 x 1 mm) (51-85150)
BOTTOM VIEW
A1 CORNER
TOP VIEW
Ø0.05 M C
Ø0.25 M C A B
A1 CORNER
Ø0.30 0.05ꢀ(48X
1
2
3
(
5
6
6
5
(
3
2
1
A
A
B
C
D
B
C
D
E
E
F
F
G
G
H
H
1.475
A
A
0.75
B
6.00 0.10
3.75
B
6.00 0.10
0.15ꢀ(8X
51-85150-*D
SEATING PLANE
C
All product and company names mentioned in this document are the trademarks of their respective holders.
Document #: 38-05130 Rev. *F
Page 9 of 10
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY7C1019CV33
Document History Page
Document Title: CY7C1019CV33 128K x 8 Static RAM
Document Number: 38-05130
Issue
Date
Orig. of
Change
REV.
**
ECN NO.
109245
113431
115047
119796
123030
419983
Description of Change
12/16/01
04/10/02
08/01/02
10/11/02
12/17/02
See ECN
HGK
NSL
HGK
DFP
DFP
NXR
New Data Sheet
AC Test Loads split based on speed
*A
*B
Added TSOP II Package and I Temp. Improved ICC limits
Updated standby current from 5 nA to 5 mA
*C
*D
*E
Updated Truth Table to reflect single Chip Enable option
Added 48-ball VFBGA Package
Added lead-free parts in Ordering Information Table
Replaced Package Name column with Package Diagram in the Ordering
Information Table
*F
493543
See ECN
NXR
Removed 8 ns speed bin from Product offering
Added note #1 on page #2
Changed the description of IIX from Input Load Current to
Input Leakage Current in DC Electrical Characteristics table
Removed IOS parameter from DC Electrical Characteristics table
Updated Ordering Information
Document #: 38-05130 Rev. *F
Page 10 of 10
相关型号：
CY7C1019CV33-12BVXIT
128KX8 STANDARD SRAM, 12ns, PBGA48, 6 X 8 MM, 1 MM HEIGHT, LEAD FREE, VFBGA-48
ROCHESTER
©2020 ICPDF网 联系我们和版权申明