ADP151AUJZ-1.8-R7 [ROCHESTER]
1.8 V FIXED POSITIVE LDO REGULATOR, PDSO5, ROHS COMPLIANT, MO-193AB, TSOT-5;
| 型号： | ADP151AUJZ-1.8-R7 |
| 厂家： | 
Rochester Electronics |
| 描述： | 1.8 V FIXED POSITIVE LDO REGULATOR, PDSO5, ROHS COMPLIANT, MO-193AB, TSOT-5 光电二极管 输出元件 调节器 |
| 文件： | 总25页 (文件大小：1494K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Ultralow Noise, 200 mA,
CMOS Linear Regulator
Data Sheet
ADP151
FEATURES
TYPICAL APPLICATION CIRCUIT
V
= 2.3V
V
= 1.8V
IN
OUT
Ultralow noise: 9 µV rms
1
2
3
VIN
GND
EN
VOUT
5
1µF
No noise bypass capacitor required
Stable with 1 µF ceramic input and output capacitors
Maximum output current: 200 mA
Input voltage range: 2.2 V to 5.5 V
Low quiescent current
1µF
ON
4
NC
OFF
NC = NO CONNECT
Figure 1. TSOT ADP151 with Fixed Output Voltage, 1.8 V
I
I
GND = 10 µA with 0 load
GND = 265 μA with 200 mA load
1
2
Low shutdown current: <1 µA
Low dropout voltage: 140 mV at 200 mA load
Initial accuracy: 1%
Accuracy over line, load, and temperature: 2.5%
16 fixed output voltage options: 1.1 V to 3.3 V
PSRR performance of 70 dB at 10 kHz
Current-limit and thermal overload protection
Logic controlled enable
V
= 1.8V
OUT
V
= 2.3V
OUT
IN
VIN
VOUT
A
B
C
C
IN
1µF
TOP VIEW
(Not to Scale)
ON
EN
GND
OFF
Figure 2. WLCSP ADP151 with Fixed Output Voltage, 1.8 V
V
= 2.3V
1µF
V
= 1.8V
IN
OUT
6
1
2
3
Internal pull-down resistor on EN input
5-lead TSOT package
6-lead LFCSP package
VIN
NC
VOUT
1µF
ADP151
TOP VIEW
5
4
NC
ON
(Not to Scale)
EN
GND
OFF
4-ball, 0.4 mm pitch WLCSP
NC = NO CONNECT. DO NOT
CONNECT TO THIS PIN.
APPLICATIONS
RF, VCO, and PLL power supplies
Mobile phones
Figure 3. LFCSP ADP151 with Fixed Output Voltage, 1.8 V
Digital camera and audio devices
Portable and battery-powered equipment
Post dc-to-dc regulation
Portable medical devices
GENERAL DESCRIPTION
The ADP151 is an ultralow noise, low dropout linear regulator
that operates from 2.2 V to 5.5 V and provides up to 200 mA
of output current. The low 140 mV dropout voltage at 200 mA
load improves efficiency and allows operation over a wide input
voltage range.
The ADP151 is specifically designed for stable operation with
tiny 1 µF, 30% ceramic input and output capacitors to meet
the requirements of high performance, space constrained
applications.
The ADP151 is capable of 16 fixed output voltage options,
ranging from 1.1 V to 3.3 V.
Using an innovative circuit topology, the ADP151 achieves
ultralow noise performance without the necessity of a bypass
capacitor, making it ideal for noise-sensitive analog and RF
applications. The ADP151 also achieves ultralow noise per-
formance without compromising PSRR or transient line and
load performance. The low 265 μA of quiescent current at
200 mA load makes the ADP151 suitable for battery-operated
portable equipment.
Short-circuit and thermal overload protection circuits prevent
damage in adverse conditions. The ADP151 is available in tiny
5-lead TSOT, 6-lead LFCSP, and 4-ball, 0.4 mm pitch, halide-free
WLCSP packages for the smallest footprint solution to meet a
variety of portable power application requirements.
The ADP151 also includes an internal pull-down resistor on the
EN input.
Rev. E
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rightsof third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2010–2012 Analog Devices, Inc. All rights reserved.
ADP151
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Performance Characteristics ..............................................7
Theory of Operation ...................................................................... 11
Applications Information.............................................................. 12
Capacitor Selection .................................................................... 12
Enable Feature ............................................................................ 13
Adjustable Output Voltage Operation..................................... 13
Current-Limit and Thermal Overload Protection................. 15
Thermal Considerations............................................................ 15
Printed Circuit Board Layout Considerations............................ 20
Outline Dimensions....................................................................... 21
Ordering Guide .......................................................................... 22
Applications....................................................................................... 1
Typical Application Circuit ............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Input and Output Capacitor, Recommended Specifications.. 4
Absolute Maximum Ratings............................................................ 5
Thermal Data................................................................................ 5
Thermal Resistance ...................................................................... 5
ESD Caution.................................................................................. 5
Pin Configurations and Function Descriptions ........................... 6
REVISION HISTORY
4/12—Rev. D to Rev. E
Added Figure 51 to Figure 56 ....................................................... 18
Added Figure 59 ............................................................................. 19
Added Figure 62 ............................................................................. 20
Added Figure 65 ............................................................................. 21
Updated Outline Dimensions....................................................... 21
Changes to Ordering Guide.......................................................... 23
Changes to Figure 33...................................................................... 13
Updated Outline Dimensions....................................................... 21
Changes to Ordering Guide .......................................................... 22
3/11—Rev. C to Rev. D
Changes to Current-Limit Threshold Temperature Range......... 4
Added EPAD Notation .................................................................... 6
Changes to Ordering Guide .......................................................... 22
8/10—Rev. 0 to Rev. A
Changes to Figure 8...........................................................................7
Changes to Figure 15 Caption and Figure 16 Caption .................8
Changes to Figure 17 Caption and Figure 18 Caption .................9
Changes to Ordering Guide.......................................................... 21
1/11—Rev. B to Rev. C
Changes to Figure 23........................................................................ 9
12/10—Rev. A to Rev. B
3/10—Revision 0: Initial Version
Added LFCSP Package.......................................................Universal
Added Figure 3; Renumbered Sequentially .................................. 1
Added Table 2 Caption; Renumbered Sequentially ..................... 4
Changes to Table 4............................................................................ 5
Added Figure 6, Changes to Table 5............................................... 6
Changes to Figure 23........................................................................ 9
Changes to Figure 37 and Figure 38............................................. 14
Rev. E | Page 2 of 24
Data Sheet
ADP151
SPECIFICATIONS
VIN = (VOUT + 0.4 V) or 2.2 V, whichever is greater; EN = VIN, IOUT = 10 mA, CIN = COUT = 1 µF, TA = 25°C, unless otherwise noted.
Table 1.
Parameter
Symbol
VIN
Conditions
Min
Typ
10
Max
Unit
V
INPUT VOLTAGE RANGE
OPERATING SUPPLY CURRENT
TJ = −40°C to +125°C
IOUT = 0 µA
IOUT = 0 µA, TJ = −40°C to +125°C
IOUT = 100 µA
IOUT = 100 µA, TJ = −40°C to +125°C
IOUT = 10 mA
IOUT = 10 mA, TJ = −40°C to +125°C
IOUT = 200 mA
2.2
5.5
IGND
µA
µA
µA
µA
µA
µA
μA
μA
µA
µA
20
20
40
60
90
265
0.2
IOUT = 200 mA, TJ = −40°C to +125°C
EN = GND
EN = GND, TJ = −40°C to +125°C
350
1.0
+1
SHUTDOWN CURRENT
OUTPUT VOLTAGE ACCURACY
TSOT/LFCSP
IGND-SD
VOUT
VOUT
IOUT = 10 mA
TJ = −40°C to +125°C
−1
%
VOUT < 1.8 V
100 µA < IOUT < 200 mA, VIN = (VOUT + 0.4 V) to 5.5 V
VOUT ≥1.8 V
100 µA < IOUT < 200 mA, VIN = (VOUT + 0.4 V) to 5.5 V
TJ = −40°C to +125°C
−3
+2
%
%
−2.5
+1.5
WLCSP
VOUT
VOUT < 1.8 V
100 µA < IOUT < 200 mA, VIN = (VOUT + 0.4 V) to 5.5 V
VOUT ≥1.8 V
100 µA < IOUT < 200 mA, VIN = (VOUT + 0.4 V) to 5.5 V
−2.5
−2
+2
%
%
+1.5
REGULATION
Line Regulation
Load Regulation (TSOT/LFCSP)1
∆VOUT/∆VIN VIN = (VOUT + 0.4 V) to 5.5 V, TJ = −40°C to +125°C
∆VOUT/∆IOUT VOUT < 1.8 V
−0.05
+0.05 %/V
%/mA
IOUT = 100 µA to 200 mA
IOUT = 100 µA to 200 mA, TJ = −40°C to +125°C
VOUT ≥ 1.8 V
0.006
0.003
0.004
%/mA
%/mA
0.012
0.008
0.009
IOUT = 100 µA to 200 mA
%/mA
%/mA
%/mA
%/mA
%/mA
IOUT = 100 µA to 200 mA, TJ = −40°C to +125°C
∆VOUT/∆IOUT VOUT < 1.8 V
Load Regulation (WLCSP)1
IOUT = 100 µA to 200 mA
IOUT = 100 µA to 200 mA, TJ = −40°C to +125°C
VOUT ≥1.8 V
IOUT = 100 µA to 200 mA
IOUT = 100 µA to 200 mA, TJ = −40°C to +125°C
0.002
10
%/mA
%/mA
mV
mV
mV
mV
mV
mV
0.006
30
DROPOUT VOLTAGE2
TSOT/LFCSP
WLCSP
VDROPOUT
IOUT = 10 mA
IOUT = 10 mA, TJ = −40°C to +125°C
IOUT = 200 mA
IOUT = 200 mA, TJ = −40°C to +125°C
IOUT = 200 mA
IOUT = 200 mA, TJ = −40°C to +125°C
150
135
230
200
Rev. E | Page 3 of 24
ADP151
Data Sheet
Parameter
START-UP TIME3
Symbol
tSTART-UP
ILIMIT
Conditions
Min
Typ
180
300
Max
Unit
µs
VOUT = 3.3 V
CURRENT-LIMIT THRESHOLD4
UNDERVOLTAGE LOCKOUT
Input Voltage Rising
Input Voltage Falling
Hysteresis
TJ = 0°C to +125°C
TJ = −40°C to +125°C
220
400
mA
UVLORISE
UVLOFALL
UVLOHYS
1.96
V
V
mV
1.28
1.2
120
THERMAL SHUTDOWN
Thermal Shutdown Threshold
Thermal Shutdown Hysteresis
TSSD
TJ rising
150
15
°C
°C
TSSD-HYS
EN INPUT
EN Input Logic High
EN Input Logic Low
EN Input Pull-Down Resistance
OUTPUT NOISE
VIH
VIL
REN
2.2 V ≤ VIN ≤ 5.5 V
2.2 V ≤ VIN ≤ 5.5 V
VIN = VEN = 5.5 V
V
V
MΩ
0.4
2.6
9
9
OUTNOISE
10 Hz to 100 kHz, VIN = 5 V, VOUT = 3.3 V
10 Hz to 100 kHz, VIN = 5 V, VOUT = 2.5 V
10 Hz to 100 kHz, VIN = 5 V, VOUT = 1.1 V
µV rms
µV rms
µV rms
9
POWER SUPPLY REJECTION RATIO
VIN = VOUT + 0.5 V
PSRR
10 kHz, VIN = 3.8 V, VOUT = 3.3 V, IOUT = 10 mA
100 kHz, VIN = 3.8 V, VOUT = 3.3 V, IOUT = 10 mA
10 kHz, VIN = 4.3 V, VOUT = 3.3 V, IOUT = 10 mA
100 kHz, VIN = 4.3 V, VOUT = 3.3 V, IOUT = 10 mA
10 kHz, VIN = 2.2 V, VOUT = 1.1 V, IOUT = 10 mA
100 kHz, VIN = 2.2 V, VOUT = 1.1 V, IOUT = 10 mA
70
55
70
55
70
55
dB
dB
dB
dB
dB
dB
VIN = VOUT + 1V
1 Based on an end-point calculation using 0.1 mA and 200 mA loads. See Figure 8 for typical load regulation performance for loads less than 1 mA.
2 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output
voltages above 2.2 V.
3 Start-up time is defined as the time between the rising edge of EN and VOUT being at 90% of its nominal value.
4 Current-limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 3.0 V
output voltage is defined as the current that causes the output voltage to drop to 90% of 3.0 V (that is, 2.7 V).
INPUT AND OUTPUT CAPACITOR, RECOMMENDED SPECIFICATIONS
Table 2.
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Minimum Input and Output
Capacitance1
CMIN
TA = −40°C to +125°C
0.7
µF
Capacitor ESR
RESR
TA = −40°C to +125°C
0.001
0.2
Ω
1 The minimum input and output capacitance should be greater than 0.7 μF over the full range of operating conditions. The full range of operating conditions in the
application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R and X5R type capacitors are recommended;
Y5V and Z5U capacitors are not recommended for use with any LDO.
Rev. E | Page 4 of 24
Data Sheet
ADP151
ABSOLUTE MAXIMUM RATINGS
Table 3.
on PCB material, layout, and environmental conditions. The
specified values of θJA are based on a 4-layer, 4 in. × 3 in. circuit
board. See JESD51-7 and JESD51-9 for detailed information
on the board construction. For additional information, see the
AN-617 Application Note, MicroCSP™ Wafer Level Chip Scale
Package, available at www.analog.com.
Parameter
Rating
VIN to GND
VOUT to GND
−0.3 V to +6.5 V
−0.3 V to VIN
EN to GND
−0.3 V to +6.5V
−65°C to +150°C
−40°C to +125°C
−40°C to +125°C
JEDEC J-STD-020
Storage Temperature Range
Operating Junction Temperature Range
Operating Ambient Temperature Range
Soldering Conditions
ΨJB is the junction-to-board thermal characterization parameter
with units of °C/W. ΨJB of the package is based on modeling and
calculation using a 4-layer board. The JESD51-12, Guidelines for
Reporting and Using Electronic Package Thermal Information, states
that thermal characterization parameters are not the same as
thermal resistances. ΨJB measures the component power flowing
through multiple thermal paths rather than a single path as in
thermal resistance, θJB. Therefore, ΨJB thermal paths include
convection from the top of the package as well as radiation from
the package, factors that make ΨJB more useful in real-world
applications. Maximum junction temperature (TJ) is calculated
from the board temperature (TB) and power dissipation (PD)
using the formula
Stresses above those listed under absolute maximum ratings
may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL DATA
Absolute maximum ratings apply individually only, not in
combination. The ADP151 can be damaged when the junction
temperature limits are exceeded. Monitoring ambient temperature
does not guarantee that TJ is within the specified temperature
limits. In applications with high power dissipation and poor
thermal resistance, the maximum ambient temperature may
have to be derated.
TJ = TB + (PD × ΨJB)
See JESD51-8 and JESD51-12 for more detailed information
about ΨJB.
THERMAL RESISTANCE
θJA and ΨJB are specified for the worst-case conditions, that is, a
device soldered in a circuit board for surface-mount packages.
In applications with moderate power dissipation and low PCB
thermal resistance, the maximum ambient temperature can
exceed the maximum limit as long as the junction temperature
is within specification limits. The junction temperature (TJ) of
the device is dependent on the ambient temperature (TA), the
power dissipation of the device (PD), and the junction-to-ambient
thermal resistance of the package (θJA).
Table 4. Thermal Resistance
Package Type
θJA
ΨJB
43
58
Unit
°C/W
°C/W
°C/W
5-Lead TSOT
4-Ball, 0.4 mm Pitch WLCSP
6-Lead 2 mm × 2 mm LFCSP
170
260
63.6
28.3
The maximum junction temperature (TJ) is calculated from the
ambient temperature (TA) and power dissipation (PD) using the
formula
ESD CAUTION
TJ = TA + (PD × θJA)
The junction-to-ambient thermal resistance (θJA) of the package
is based on modeling and calculation using a 4-layer board. The
junction-to-ambient thermal resistance is highly dependent
on the application and board layout. In applications where high
maximum power dissipation exists, close attention to thermal
board design is required. The value of θJA may vary, depending
Rev. E | Page 5 of 24
ADP151
Data Sheet
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
1
2
VOUT 1
6 VIN
1
2
3
5
VIN
GND
EN
VOUT
ADP151
TOP VIEW
(Not to Scale)
ADP151
TOP VIEW
(Not to Scale)
2
5
NC
NC
A
VIN
VOUT
TOP VIEW
(Not to Scale)
4 EN
GND 3
4
NC
NOTES
B
EN
GND
NC = NO CONNECT
1. NC = NO CONNECT. DO NOT CONNECT TO THIS PIN.
2. THE EXPOSED PAD MUST BE CONNECTED TO GROUND.
Figure 4. 5-Lead TSOT Pin Configuration
Figure 5. 4-Ball WLCSP Pin Configuration
Figure 6. 6-Lead LFCSP Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
TSOT
WLCSP LFCSP
Mnemonic
VIN
GND
Description
1
2
3
A1
B2
B1
6
3
4
Regulator Input Supply. Bypass VIN to GND with a 1 µF or greater capacitor.
Ground.
Enable Input. Drive EN high to turn on the regulator; drive EN low to turn off the regulator.
For automatic startup, connect EN to VIN.
EN
4
5
N/A
N/A
N/A
A2
N/A
N/A
2
1
5
NC
VOUT
NC
No Connect. Not connected internally.
Regulated Output Voltage. Bypass VOUT to GND with a 1 µF or greater capacitor.
No Connect. Not connected internally.
Exposed Pad. The exposed pad must be connected to ground. The exposed pad enhances
the thermal performance of the package.
EPAD
Rev. E | Page 6 of 24
Data Sheet
ADP151
TYPICAL PERFORMANCE CHARACTERISTICS
VIN = 5 V, VOUT = 3.3 V, IOUT = 1 mA, CIN = COUT = 1 µF, TA = 25°C, unless otherwise noted.
3.35
3.33
3.31
3.29
3.27
3.25
1k
100
10
LOAD = 10µA
LOAD = 100µA
LOAD = 1mA
LOAD = 10mA
LOAD = 100mA
LOAD = 200mA
LOAD = 10µA
LOAD = 100µA
LOAD = 1mA
LOAD = 10mA
LOAD = 100mA
LOAD = 200mA
1
–40
–5
25
85
125
–40
–5
25
85
125
JUNCTION TEMPERATURE (°C)
JUNCTION TEMPERATURE (°C)
Figure 7. Output Voltage vs. Junction Temperature
Figure 10. Ground Current vs. Junction Temperature
3.35
3.33
3.31
3.29
3.27
3.25
1k
100
10
0.01
0.1
1
10
(mA)
100
1000
0.01
0.1
1
10
(mA)
100
1000
I
I
LOAD
LOAD
Figure 8. Output Voltage vs. Load Current
Figure 11. Ground Current vs. Load Current
3.35
3.33
3.31
3.29
3.27
3.25
1k
100
10
LOAD = 10µA
LOAD = 100µA
LOAD = 1mA
LOAD = 10mA
LOAD = 100mA
LOAD = 200mA
LOAD = 10µA
LOAD = 100µA
LOAD = 1mA
LOAD = 10mA
LOAD = 100mA
LOAD = 200mA
3.6
3.8
4.0
4.2
4.4
4.6
(V)
4.8
5.0
5.2
5.4
3.6
3.8
4.0
4.2
4.4
4.6
(V)
4.8
5.0
5.2
5.4
V
V
IN
IN
Figure 9. Output Voltage vs. Input Voltage
Figure 12. Ground Current vs. Input Voltage
Rev. E | Page 7 of 24
ADP151
Data Sheet
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
800
700
600
500
400
300
200
100
0
I
= 1mA
= 5mA
= 10mA
= 50mA
= 100mA
= 200mA
V
V
V
V
V
V
= 3.6V
= 3.8V
= 4.2V
= 4.4V
= 4.8V
= 5.5V
OUT
OUT
OUT
OUT
OUT
OUT
IN
IN
IN
IN
IN
IN
I
I
I
I
I
0
–50
–25
0
25
50
75
100
125
3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55
TEMPERATURE (°C)
V
(V)
IN
Figure 13. Shutdown Current vs. Temperature at Various Input Voltages
Figure 16. Ground Current vs. Input Voltage (in Dropout)
0
120
100
80
60
40
20
0
200mA
100mA
10mA
1mA
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
100µA
10
100
1k
10k
100k
1M
10M
1
10
100
1000
FREQUENCY (Hz)
I
(mA)
LOAD
Figure 14. Dropout Voltage vs. Load Current
Figure 17. Power Supply Rejection Ratio vs. Frequency, VOUT = 1.2 V, VIN = 2.2 V
3.40
3.35
3.30
3.25
3.20
3.15
3.10
3.05
3.00
0
200mA
100mA
10mA
1mA
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
100µA
I
I
I
I
I
I
= 1mA
= 5mA
= 10mA
= 50mA
= 100mA
= 200mA
OUT
OUT
OUT
OUT
OUT
OUT
3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55
10
100
1k
10k
100k
1M
10M
V
(V)
FREQUENCY (Hz)
IN
Figure 18. Power Supply Rejection Ratio vs. Frequency, VOUT = 2.8 V, VIN = 3.3 V
Figure 15. Output Voltage vs. Input Voltage (in Dropout)
Rev. E | Page 8 of 24
Data Sheet
ADP151
0
14
13
12
11
10
9
200mA
3.3V
2.8V
1.2V
1.1V
100mA
10mA
1mA
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
100µA
8
7
6
5
4
3
2
1
0
10
100
1k
10k
100k
1M
10M
0.001
0.01
0.1
1
10
100
1k
FREQUENCY (Hz)
LOAD CURRENT (mA)
Figure 19. Power Supply Rejection Ratio vs. Frequency, VOUT = 3.3 V, VIN = 3.8 V
Figure 22. Output Noise vs. Load Current and Output Voltage,
VIN = 5 V, COUT = 1 μF
0
1000
100
10
3.3V
2.8V
1.2V
1.1V
V
V
V
V
V
V
= 3.3V, I
= 3.3V, I
= 2.8V, I
= 2.8V, I
= 1.1V, I
= 1.1V, I
= 200mA
= 10mA
= 200mA
= 10mA
= 200mA
= 10mA
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
10
100
1k
10k
100k
1M
10M
10
100
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 20. Power Supply Rejection Ratio vs. Frequency at Various Output Voltages
and Load Currents, VOUT − VIN = 0.5 V, except for VOUT = 1.1 V, VIN = 2.2 V
Figure 23. Output Noise Spectral Density vs. Frequency,
VIN = 5 V, ILOAD = 10 mA, COUT = 1 μF
0
T
I
I
I
I
= 200mA, V = 3.3V
IN
= 10mA, V =3.3V
IN
= 200mA, V = 3.8V
IN
= 10mA, V = 3.8V
IN
OUT
OUT
OUT
OUT
LOAD CURRENT
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
1
2
V
OUT
CH1 200mA CH2 50mV
M20µs
T
A
CH1
64.0mA
10
100
1k
10k
100k
1M
10M
10.00%
FREQUENCY (Hz)
Figure 21. Power Supply Rejection Ratio vs. Frequency at Various Voltages
and Load Currents, VOUT = 2.8 V
Figure 24. Load Transient Response, CIN, COUT = 1 μF, ILOAD = 1 mA to 200 mA
Rev. E | Page 9 of 24
ADP151
Data Sheet
T
T
INPUT VOLTAGE
INPUT VOLTAGE
2
1
2
1
V
V
OUT
OUT
CH1 1V
CH2 2mV
M10µs
A
CH1
4.56V
CH1 1V
CH2 2mV
M10µs
A
CH1
4.56V
T
10.80%
T 10.80%
Figure 25. Line Transient Response, CIN, COUT = 1 μF, ILOAD = 200 mA
Figure 26. Line Transient Response, CIN, COUT = 1 μF, ILOAD = 1 mA
Rev. E | Page 10 of 24
Data Sheet
ADP151
THEORY OF OPERATION
The ADP151 is an ultralow noise, low quiescent current, low
dropout linear regulator that operates from 2.2 V to 5.5 V and
can provide up to 200 mA of output current. Drawing a low
265 μA of quiescent current (typical) at full load makes the
ADP151 ideal for battery-operated portable equipment.
Shutdown current consumption is typically 200 nA.
Internally, the ADP151 consists of a reference, an error amplifier, a
feedback voltage divider, and a PMOS pass transistor. Output
current is delivered via the PMOS pass device, which is controlled
by the error amplifier. The error amplifier compares the reference
voltage with the feedback voltage from the output and amplifies
the difference. If the feedback voltage is lower than the reference
voltage, the gate of the PMOS device is pulled lower, allowing
more current to pass and increasing the output voltage. If the
feedback voltage is higher than the reference voltage, the gate of
the PMOS device is pulled higher, allowing less current to pass
and decreasing the output voltage.
Using new innovative design techniques, the ADP151 provides
superior noise performance for noise-sensitive analog and RF
applications without the need for a noise bypass capacitor. The
ADP151 is also optimized for use with small 1 µF ceramic
capacitors.
An internal pull-down resistor on the EN input holds the input
low when the pin is left open.
VIN
GND
EN
VOUT
The ADP151 is available in 16 output voltage options, ranging
from 1.1 V to 3.3 V. The ADP151 uses the EN pin to enable and
disable the VOUT pin under normal operating conditions. When
EN is high, VOUT turns on; when EN is low, VOUT turns off.
For automatic startup, EN can be tied to VIN.
R1
SHORT-CIRCUIT,
UVLO, AND
THERMAL
PROTECT
SHUTDOWN
R2
REFERENCE
R
EN
Figure 27. Internal Block Diagram
Rev. E | Page 11 of 24
ADP151
Data Sheet
APPLICATIONS INFORMATION
Figure 29 depicts the capacitance vs. voltage bias characteristic
of an 0402, 1 µF, 10 V X5R capacitor. The voltage stability of a
capacitor is strongly influenced by the capacitor size and voltage
rating. In general, a capacitor in a larger package or higher voltage
rating exhibits better stability. The temperature variation of the
X5R dielectric is ~ 15% over the −40°C to +85°C temperature
range and is not a function of package or voltage rating.
1.2
CAPACITOR SELECTION
Output Capacitor
The ADP151 is designed for operation with small, space-saving
ceramic capacitors but can function with most commonly used
capacitors as long as care is taken with regard to the effective
series resistance (ESR) value. The ESR of the output capacitor
affects the stability of the LDO control loop. A minimum of 1 µF
capacitance with an ESR of 1 Ω or less is recommended to ensure
the stability of the ADP151. Transient response to changes in load
current is also affected by output capacitance. Using a larger value
of output capacitance improves the transient response of the
ADP151 to large changes in load current. Figure 28 shows the
transient responses for an output capacitance value of 1 µF.
1.0
0.8
0.6
0.4
0.2
0
T
LOAD CURRENT
1
0
2
4
6
8
10
VOLTAGE BIAS
2
Figure 29. Capacitance vs. Voltage Bias Characteristic
V
OUT
Use Equation 1 to determine the worst-case capacitance, accounting
for capacitor variation over temperature, component tolerance,
and voltage.
CH1 200mA CH2 50mV
M20µs
A
CH1
64mA
CEFF = CBIAS × (1 − TEMPCO) × (1 − TOL)
(1)
T
10.00%
where:
Figure 28. Output Transient Response, COUT = 1 µF
C
BIAS is the effective capacitance at the operating voltage.
Input Bypass Capacitor
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
Connecting a 1 µF capacitor from VIN to GND reduces
the circuit sensitivity to the printed circuit board (PCB) layout,
especially when long input traces or high source impedance
are encountered. If greater than 1 µF of output capacitance is
required, the input capacitor should be increased to match it.
In this example, the worst-case temperature coefficient (TEMPCO)
over −40°C to +85°C is assumed to be 15% for an X5R dielectric.
The tolerance of the capacitor (TOL) is assumed to be 10%, and
C
BIAS is 0.94 μF at 1.8 V, as shown in Figure 29.
Substituting these values in Equation 1 yields
EFF = 0.94 μF × (1 − 0.15) × (1 − 0.1) = 0.719 μF
Input and Output Capacitor Properties
C
Any good quality ceramic capacitor can be used with the
ADP151, as long as it meets the minimum capacitance and
maximum ESR requirements. Ceramic capacitors are manufac-
tured with a variety of dielectrics, each with different behavior
over temperature and applied voltage. Capacitors must have an
adequate dielectric to ensure the minimum capacitance over the
necessary temperature range and dc bias conditions. X5R or X7R
dielectrics with a voltage rating of 6.3 V or 10 V are recommended.
Y5V and Z5U dielectrics are not recommended, due to their
poor temperature and dc bias characteristics.
Therefore, the capacitor chosen in this example meets the
minimum capacitance requirement of the LDO over tempera-
ture and tolerance at the chosen output voltage.
To guarantee the performance of the ADP151, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
Rev. E | Page 12 of 24
Data Sheet
ADP151
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
ENABLE FEATURE
The ADP151 uses the EN pin to enable and disable the VOUT
pin under normal operating conditions. As shown in Figure 30,
when a rising voltage on EN crosses the active threshold, VOUT
turns on. When a falling voltage on EN crosses the inactive
threshold, VOUT turns off.
3.0
2.5
2.0
1.5
1.0
0.5
0
ENABLE
3.3V
2.8V
1.1V
0
50
100
150
200
250
300
350
400
450
TIME (µs)
Figure 32. Typical Start-Up Behavior
ADJUSTABLE OUTPUT VOLTAGE OPERATION
The unique architecture of the ADP151 makes an adjustable
version difficult to implement in silicon. However, it is possible
to create an adjustable regulator at the expense of increasing the
quiescent current of the regulator circuit.
0
0.5
1.0
1.5
2.0
2.5
ENABLE VOLTAGE
Figure 30. ADP151 Typical EN Pin Operation
The ADP151, and similar LDOs, are designed to regulate the
output voltage, VOUT, appearing at the VOUT pin with respect
to the GND pin. If the GND pin is at a potential other than 0 V
(for example, at VOFFSET), the ADP151 output voltage is VOUT
OFFSET. By taking advantage of this behavior, it is possible to
As shown in Figure 30, the EN pin has hysteresis built in. This
prevents on/off oscillations that can occur due to noise on the
EN pin as it passes through the threshold points.
+
V
The EN pin active/inactive thresholds are derived from the VIN
voltage. Therefore, these thresholds vary with changing input
voltage. Figure 31 shows typical EN active/inactive thresholds
when the input voltage varies from 2.2 V to 5.5 V.
1200
create an adjustable ADP151 circuit that retains most of the
desirable characteristics of the ADP151.
V
V
IN
OUT
1
2
3
VIN
GND
EN
VOUT
U1
5
C1
C2
1000
4
NC
V
OFFSET
R2
V
RISE
EN
800
600
400
200
0
R1
C3
V
FALL
EN
V
= V × (1 + R2/R1)
LDO
OUT
Figure 33. Adjustable LDO Using the ADP151
The circuit shown in Figure 33 is an example of an adjustable
LDO using the ADP151. A stable VOFFSET voltage is created by
passing a known current through R2. The current through R2 is
determined by the voltage across R1. Because the voltage across
R1 is set by the voltage between VOUT and GND, the current
passing through R2 is fixed, and VOFFSET is stable.
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
INPUT VOLTAGE
To minimize the effect variation of the ADP151 ground current
(IGND) with load, it is best to keep R1 as small as possible. It is
also best to size the current passing through R2 to at least 20×
greater than the maximum expected ground current.
Figure 31. Typical EN Pin Thresholds vs. Input Voltage
The ADP151 uses an internal soft start to limit the inrush current
when the output is enabled. The start-up time for the 3.3 V
option is approximately 160 μs from the time the EN active
threshold is crossed to when the output reaches 90% of its final
value. As shown in Figure 32, the start-up time is dependent on
the output voltage setting.
To create a 4 V LDO circuit, start with the 3.3 V version of the
ADP151 to minimize the value of R2. Because VOUT is 4 V,
V
OFFSET must be 0.7 V, and the current through R2 must be 7 mA.
R1 is, therefore, 3.3 V/7 mA or 471 Ω. A 470 Ω standard value
introduces less than 1% error. Capacitor C3 is necessary to stabilize
the LDO; a value of 1 μF is adequate.
Rev. E | Page 13 of 24
ADP151
Data Sheet
11
10
9
Figure 34 through Figure 38 show the typical performance of the
4 V LDO circuit.
The noise performance of the 4 V LDO circuit is only about 1 μV
worse than the same LDO used at 3.3 V because the output noise of
the circuit is almost solely determined by the LDO and not the
external components. The small difference may be attributed to the
internally generated noise in the LDO ground current working with
R2. By keeping R2 small, this noise contribution can be minimized.
The PSRR of the 4 V circuit is as much as 10 dB poorer than the
3.3 V LDO with 500 mV of headroom because the ground current
of the LDO varies slightly with input voltage. This, in turn,
modulates VOFFSET and reduces the PSRR of the regulator. By
increasing the headroom to 1 V, the PSRR performance is
nearly restored to the performance of the fixed output LDO.
4.04
8
1
10
100
1k
LOAD CURRENT (mA)
Figure 36. 4 V LDO Circuit, Typical RMS Output Noise, 10 Hz to 100 kHz
0
200mA
100mA
50mA
10mA
–10
4.03
4.02
4.01
4.00
–20
–30
–40
–50
–60
–70
–80
–90
–100
3.99
LOAD = 10mA
LOAD = 20mA
LOAD = 50mA
LOAD = 100mA
LOAD = 150mA
LOAD = 200mA
3.98
3.97
3.96
–40
–5
25
85
125
10
100
1k
10k
100k
1M
10M
JUNCTION TEMPERATURE (°C)
FREQUENCY (Hz)
Figure 34. 4 V LDO Circuit, Typical Load Regulation over Temperature
Figure 37. 4 V LDO Circuit, Typical PSRR vs. Load Current, 1 V Headroom
4.040
0
LOAD = 10mA
200mA
100mA
50mA
10mA
LOAD = 20mA
4.035
–10
LOAD = 50mA
LOAD = 100mA
–20
–30
–40
–50
–60
–70
–80
–90
–100
4.030
LOAD = 150mA
LOAD = 200mA
4.025
4.020
4.015
4.010
4.005
4.000
4.4
4.6
4.8
5.0
(V)
5.2
5.4
10
100
1k
10k
100k
1M
10M
V
IN
FREQUENCY (Hz)
Figure 35. 4 V LDO Circuit, Typical Line Regulation over Load Current
Figure 38. 4 V LDO Circuit, Typical PSRR vs. Load Current, 500 mV Headroom
Rev. E | Page 14 of 24
Data Sheet
ADP151
To guarantee reliable operation, the junction temperature of
CURRENT-LIMIT AND THERMAL OVERLOAD
PROTECTION
the ADP151 must not exceed 125°C. To ensure that the junction
temperature stays below this maximum value, the user must be
aware of the parameters that contribute to junction temperature
changes. These parameters include ambient temperature, power
dissipation in the power device, and thermal resistances between
the junction and ambient air (θJA). The θJA number is dependent
on the package assembly compounds that are used and the amount
of copper used to solder the package GND pins to the PCB.
The ADP151 is protected against damage due to excessive
power dissipation by current and thermal overload protection
circuits. The ADP151 is designed to current limit when the
output load reaches 300 mA (typical). When the output load
exceeds 300 mA, the output voltage is reduced to maintain a
constant current limit.
Thermal overload protection is included, which limits the
junction temperature to a maximum of 150°C (typical). Under
extreme conditions (that is, high ambient temperature and
power dissipation) when the junction temperature starts to
rise above 150°C, the output is turned off, reducing the output
current to 0. When the junction temperature drops below
135°C, the output is turned on again, and output current is
restored to its nominal value.
Table 6 shows typical θJA values of the 5-lead TSOT, 6-lead
L F C SP, a n d 4 -ball WLCSP packages for various PCB copper sizes.
Table 7 shows the typical ΨJB values of the 5-lead TSOT, 6-lead
LFCSP, and 4-ball WLCSP.
Table 6. Typical θJA Values
θ
JA (°C/W)
Copper Size (mm2)
01
TSOT
170
152
146
134
131
WLCSP
260
159
157
153
LFCSP
231.2
161.8
150.1
111.5
91.8
Consider the case where a hard short from VOUT to ground
occurs. At first, the ADP151 current limits, so that only 300 mA
is conducted into the short. If self-heating of the junction
causes its temperature to rise above 150°C, thermal shutdown
activates, turning off the output and reducing the output current
to 0. As the junction temperature cools and drops below
135°C, the output turns on and conducts 300 mA into the
short, again causing the junction temperature to rise above
150°C. This thermal oscillation between 135°C and 150°C causes a
current oscillation between 300 mA and 0 mA that continues
as long as the short remains at the output.
50
100
300
500
151
1 Device soldered to minimum size pin traces.
Table 7. Typical ΨJB Values
Model
ΨJB (°C/W)
TSOT
43
WLCSP
LFCSP
58
28.3
Current- and thermal-limit protections are intended to protect
the device against accidental overload conditions. For reliable
operation, device power dissipation must be externally limited
so that junction temperatures do not exceed 125°C.
The junction temperature of the ADP151 can be calculated
from the following equation:
TJ = TA + (PD × θJA)
(2)
(3)
where:
THERMAL CONSIDERATIONS
TA is the ambient temperature.
PD is the power dissipation in the die, given by
In most applications, the ADP151 does not dissipate much heat
due to its high efficiency. However, in applications with a high
ambient temperature and a high supply voltage to output voltage
differential, the heat dissipated in the package can cause the
junction temperature of the die to exceed the maximum junction
temperature of 125°C.
PD = [(VIN − VOUT) × ILOAD] + (VIN × IGND
where:
)
I
LOAD is the load current.
IGND is the ground current.
V
IN and VOUT are input and output voltages, respectively.
When the junction temperature exceeds 150°C, the converter
enters thermal shutdown. It recovers only after the junction
temperature has decreased below 135°C to prevent any permanent
damage. Therefore, thermal analysis for the chosen application
is very important to guarantee reliable performance over all
conditions. The junction temperature of the die is the sum of
the ambient temperature of the environment and the tempera-
ture rise of the package due to the power dissipation, as shown
in Equation 2.
Power dissipation due to ground current is quite small and can
be ignored. Therefore, the junction temperature equation
simplifies to the following:
TJ = TA + {[(VIN − VOUT) × ILOAD] × θJA}
(4)
As shown in Equation 4, for a given ambient temperature, input-to-
output voltage differential, and continuous load current, there
exists a minimum copper size requirement for the PCB to ensure
that the junction temperature does not rise above 125°C. Figure 39
through Figure 59 show junction temperature calculations for
various ambient temperatures, load currents, VIN-to-VOUT
differentials, and areas of PCB copper.
Rev. E | Page 15 of 24
ADP151
Data Sheet
140
120
100
80
140
120
100
80
MAXIMUM JUNCTION TEMPERATURE
MAXIMUM JUNCTION TEMPERATURE
60
60
40
40
20
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
0
0.3
0
0.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
4.8
4.8
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
4.8
4.8
V
V
IN
OUT
IN
OUT
Figure 39. WLCSP 500 mm2 of PCB Copper, TA = 25°C
Figure 42. WLCSP 500 mm2 of PCB Copper, TA = 50°C
140
120
100
80
140
120
100
80
MAXIMUM JUNCTION TEMPERATURE
MAXIMUM JUNCTION TEMPERATURE
60
60
40
40
20
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
0
0
0.3
0.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
V
V
IN
OUT
IN
OUT
Figure 40. WLCSP 100 mm2 of PCB Copper, TA = 25°C
Figure 43. WLCSP 100 mm2 of PCB Copper, TA = 50°C
140
120
100
80
140
120
100
80
MAXIMUM JUNCTION TEMPERATURE
MAXIMUM JUNCTION TEMPERATURE
60
60
40
40
20
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
0
0
0.3
0.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
V
V
IN
OUT
IN
OUT
Figure 41. WLCSP 50 mm2 of PCB Copper, TA = 25°C
Figure 44. WLCSP 50 mm2 of PCB Copper, TA = 50°C
Rev. E | Page 16 of 24
Data Sheet
ADP151
140
120
100
80
140
120
100
80
MAXIMUM JUNCTION TEMPERATURE
MAXIMUM JUNCTION TEMPERATURE
60
60
40
40
20
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
0
0.3
0
0.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
V
V
IN
OUT
IN
OUT
Figure 45. TSOT 500 mm2 of PCB Copper, TA = 25°C
Figure 48. TSOT 500 mm2 of PCB Copper, TA = 50°C
140
140
120
100
80
MAXIMUM JUNCTION TEMPERATURE
MAXIMUM JUNCTION TEMPERATURE
120
100
80
60
40
20
0
60
40
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
0
0.3
0.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
V
V
IN
OUT
IN
OUT
Figure 46. TSOT 100 mm2 of PCB Copper, TA = 25°C
Figure 49. TSOT 100 mm2 of PCB Copper, TA = 50°C
140
120
100
80
140
120
100
80
MAXIMUM JUNCTION TEMPERATURE
MAXIMUM JUNCTION TEMPERATURE
60
60
40
40
20
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
0
0.3
0
0.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
V
V
IN
OUT
IN
OUT
Figure 47. TSOT 50 mm2 of PCB Copper, TA = 25°C
Figure 50. TSOT 50 mm2 of PCB Copper, TA = 50°C
Rev. E | Page 17 of 24
ADP151
Data Sheet
140
120
100
80
140
120
100
80
MAXIMUM JUNCTION TEMPERATURE
MAXIMUM JUNCTION TEMPERATURE
60
60
40
40
20
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
0
0.3
0
0.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
V
V
IN
OUT
IN
OUT
Figure 51. LFCSP 500 mm2 of PCB Copper, TA = 25°C
Figure 54. LFCSP 500 mm2 of PCB Copper, TA = 50°C
140
120
100
80
140
120
100
80
MAXIMUM JUNCTION TEMPERATURE
MAXIMUM JUNCTION TEMPERATURE
60
60
40
40
20
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
0
0.3
0
0.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
V
V
IN
OUT
IN
OUT
Figure 52. LFCSP 100 mm2 of PCB Copper, TA = 25°C
Figure 55. LFCSP 100 mm2 of PCB Copper, TA = 50°C
140
120
100
80
140
120
100
80
MAXIMUM JUNCTION TEMPERATURE
MAXIMUM
JUNCTION
TEMPERATURE
60
60
40
40
20
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
0
0.3
0
0.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
V
V
IN
OUT
IN
OUT
Figure 53. LFCSP 50 mm2 of PCB Copper, TA = 25°C
Figure 56. LFCSP 50 mm2 of PCB Copper, TA = 50°C
Rev. E | Page 18 of 24
Data Sheet
ADP151
140
120
100
80
In the case where the board temperature is known, use the
thermal characterization parameter, ΨJB, to estimate the
junction temperature rise (see Figure 57 and Figure 58).
Maximum junction temperature (TJ) is calculated from the
board temperature (TB) and power dissipation (PD) using the
following formula:
MAXIMUM JUNCTION TEMPERATURE
60
TJ = TB + (PD × ΨJB)
(5)
The typical value of ΨJB is 58°C/W for the 4-ball WLCSP package,
43°C/W for the 5-lead TSOT package, and 28.3°C/W for the 6-lead
LFCSP package.
40
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
140
0
0.3
MAXIMUM JUNCTION TEMPERATURE
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
V
120
100
80
IN
OUT
Figure 58. TSOT, TA = 85°C
140
120
100
80
MAXIMUM JUNCTION TEMPERATURE
60
40
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
60
0
0.3
0.8
1.3
1.8
2.3
– V
2.8
(V)
3.3
3.8
4.3
4.8
40
V
IN
OUT
20
I
I
I
= 1mA
= 10mA
= 50mA
I
I
I
= 100mA
= 150mA
= 200mA
Figure 57. WLCSP, TA = 85°C
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
0
0.3
1.3
2.3
3.3
(V)
4.3
5.3
V
– V
OUT
IN
Figure 59. LFCSP, TA = 85°C
Rev. E | Page 19 of 24
ADP151
Data Sheet
PRINTED CIRCUIT BOARD LAYOUT CONSIDERATIONS
Heat dissipation from the package can be improved by increasing
the amount of copper attached to the pins of the ADP151.
However, as listed in Table 6, a point of diminishing returns
is eventually reached, beyond which an increase in the copper
size does not yield significant heat dissipation benefits.
Place the input capacitor as close as possible to the VIN and
GND pins. Place the output capacitor as close as possible to the
VOUT and GND pins. Use of 0402 or 0603 size capacitors and
resistors achieves the smallest possible footprint solution on
boards where area is limited.
Figure 61. Example WLCSP PCB Layout
Figure 60. Example TSOT PCB Layout
Figure 62. Example LFCSP PCB Layout
Rev. E | Page 20 of 24
Data Sheet
ADP151
OUTLINE DIMENSIONS
2.90 BSC
5
1
4
3
2.80 BSC
1.60 BSC
2
0.95 BSC
1.90
BSC
*
0.90 MAX
0.70 MIN
*
1.00 MAX
0.20
0.08
8°
4°
0°
0.10 MAX
0.50
0.30
0.60
0.45
0.30
SEATING
PLANE
*
COMPLIANT TO JEDEC STANDARDS MO-193-AB WITH
THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS.
Figure 63. 5-Lead Thin Small Outline Transistor Package [TSOT]
(UJ-5)
Dimensions show in millimeters
0.660
0.600
0.800
0.760 SQ
0.430
0.540
0.400
0.720
0.370
SEATING
PLANE
2
1
A
B
0.280
0.260
0.240
BALL A1
IDENTIFIER
0.40
BALL PITCH
TOP VIEW
(BALL SIDE DOWN)
BOTTOM VIEW
(BALL SIDE UP)
0.230
0.200
0.170
0.050 NOM
COPLANARITY
Figure 64. 4-Ball Wafer Level Chip Scale Package [WLCSP]
(CB-4-3)
Dimensions show in millimeters
1.70
1.60
2.00
BSC SQ
1.50
0.65 BSC
6
4
PIN 1 INDEX
AREA
EXPOSED
PAD
1.10
1.00
0.90
0.425
0.350
0
.275
3
1
PIN 1
INDICATOR
(R 0.15)
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.60
0.55
0.50
0.05 MAX
0.02 NOM
SECTION OF THIS DATA SHEET.
SEATING
PLANE
0.35
0.30
0.25
0.20 REF
Figure 65. 6-Lead Lead Frame Chip Scale Package [LFCSP_UD]
2.00 mm × 2.00 mm Body, Ultra Thin, Dual Lead
(CP-6-3)
Dimensions show in millimeters
Rev. E | Page 21 of 24
ADP151
Data Sheet
ORDERING GUIDE
Model1
Temperature Range
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
Output Voltage (V)2
Package Description
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
5-Lead TSOT
5-Lead TSOT
5-Lead TSOT
5-Lead TSOT
Package Option3
Branding
8R
4R
4S
4T
4U
8Q
4V
4X
4Y
4Z
50
5E
LF6
LF7
LF8
LF9
LFG
LFH
LFJ
LF6
LF7
LF8
LF9
LKZ
LFG
LFH
LFJ
ADP151ACBZ-1.1-R7
ADP151ACBZ-1.2-R7
ADP151ACBZ-1.5-R7
ADP151ACBZ-1.8-R7
ADP151ACBZ-2.5-R7
ADP151ACBZ-2.6-R7
ADP151ACBZ-2.75-R7
ADP151ACBZ-2.8-R7
ADP151ACBZ-2.85-R7
ADP151ACBZ-3.0-R7
ADP151ACBZ-3.3-R7
ADP151ACBZ-2.1-R7
ADP151AUJZ-1.2-R7
ADP151AUJZ-1.5-R7
ADP151AUJZ-1.8-R7
ADP151AUJZ-2.5-R7
ADP151AUJZ-2.8-R7
ADP151AUJZ-3.0-R7
ADP151AUJZ-3.3-R7
ADP151ACPZ-1.2-R7
ADP151ACPZ-1.5-R7
ADP151ACPZ-1.8-R7
ADP151ACPZ-2.5-R7
ADP151ACPZ-2.7-R7
ADP151ACPZ-2.8-R7
ADP151ACPZ-3.0-R7
ADP151ACPZ-3.3-R7
ADP151UJZ-REDYKIT
ADP151CPZ-REDYKIT
ADP151CB-3.3-EVALZ
1.1
1.2
1.5
1.8
2.5
2.6
2.75
2.8
2.85
3.0
3.3
2.1
1.2
1.5
1.8
2.5
2.8
3.0
3.3
1.2
1.5
1.8
2.5
2.7
2.8
3.0
3.3
CB-4-1
CB-4-3
CB-4-3
CB-4-3
CB-4-3
CB-4-3
CB-4-3
CB-4-3
CB-4-3
CB-4-3
CB-4-3
CB-4-3
UJ-5
UJ-5
UJ-5
UJ-5
UJ-5
UJ-5
UJ-5
CP-6-3
CP-6-3
CP-6-3
CP-6-3
CP-6-3
CP-6-3
CP-6-3
CP-6-3
5-Lead TSOT
5-Lead TSOT
5-Lead TSOT
6-Lead LFCSP_UD
6-Lead LFCSP_UD
6-Lead LFCSP_UD
6-Lead LFCSP_UD
6-Lead LFCSP_UD
6-Lead LFCSP_UD
6-Lead LFCSP_UD
6-Lead LFCSP_UD
Evaluation Board Kit
Evaluation Board Kit
Evaluation Board
1 Z = RoHS Compliant Part.
2 For additional voltage options for the ADP151ACBZ package option, contact a local Analog Devices, Inc., sales or distribution representative.
3 The ADP151ACBZ package option is halide free.
Rev. E | Page 22 of 24
Data Sheet
NOTES
ADP151
Rev. E | Page 23 of 24
ADP151
NOTES
Data Sheet
©2010–2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08627-0-4/12(E)
Rev. E | Page 24 of 24
相关型号：
ADP151AUJZ-2.5-R7
2.5 V FIXED POSITIVE LDO REGULATOR, 0.23 V DROPOUT, PDSO5, ROHS COMPLIANT, MO-193AB, TSOT-5
ROCHESTER
ADP151AUJZ-2.8-R7
2.8 V FIXED POSITIVE LDO REGULATOR, 0.23 V DROPOUT, PDSO5, ROHS COMPLIANT, MO-193AB, TSOT-5
ROCHESTER
ADP151AUJZ-3.0-R7
3 V FIXED POSITIVE LDO REGULATOR, 0.23 V DROPOUT, PDSO5, ROHS COMPLIANT, MO-193AB, TSOT-5
ROCHESTER
©2020 ICPDF网 联系我们和版权申明