ADE7759ARSZ_技术文档

Active Energy Metering IC with

di/dt Sensor Interface

a

ADE7759^*

FEATURES

High Accuracy, Supports IEC 687/1036

can be switched off if the ADE7759 is used with conventional

current sensors.

On-Chip Digital Integrator Allows Direct Interface with

Current Sensors with di/dt Output Such as Rogowski Coil

Less Than 0.1% Error over a Dynamic Range of 1000 to 1

On-Chip User-Programmable Threshold for Line Voltage

SAG Detection and PSU Supervisory

The ADE7759 contains a sampled waveform register and an

active energy register capable of holding at least 11.53 seconds

of accumulated power at full ac load. Data is read from the

ADE7759 via the serial interface. The ADE7759 also provides a

pulse output (CF) with frequency that is proportional to the

active power.

Supplies Sampled Waveform Data and Active Energy

(40 Bits)

In addition to active power information, the ADE7759 also

provides various system calibration features, i.e., channel offset

correction, phase calibration, and power offset correction. The

part also incorporates a detection circuit for short duration

voltage drop (SAG). The voltage threshold and the duration (in

number of half-line cycles) of the drop are user programmable.

An open-drain logic output (SAG) goes active low when a sag

event occurs.

Digital Power, Phase, and Input DC Offset Calibration

On-Chip Temperature Sensor (Typical 1 LSB/ꢀC Resolution)

SPI Compatible Serial Interface

Pulse Output with Programmable Frequency

Interrupt Request Pin (IRQ) and IRQ Status Register

Proprietary ADCs and DSP provide High Accuracy over

Large Variations in Environmental Conditions and Time

Reference 2.4 V ꢁ 8% (20 ppm/ꢀC Typical) with External

Overdrive Capability

A zero crossing output (ZX) produces an output that is synchro-

nized to the zero crossing point of the line voltage. This output

can be used to extract timing or frequency information from the

line. The signal is also used internally to the chip in the line

cycle energy accumulation mode; i.e., the number of half-line

cycles in which the energy accumulation occurs can be con-

trolled. Line cycle energy accumulation enables a faster and

more precise energy accumulation and is especially useful dur-

ing calibration. This signal is also useful for synchronization of

relay switching with a voltage zero crossing.

Single 5 V Supply, Low Power Consumption (25 mW

Typical)

GENERAL DESCRIPTION

The ADE7759 is an accurate active power and energy measure-

ment IC with a serial interface and a pulse output. The ADE7759

incorporates two second-order Σ-∆ ADCs, a digital integrator

(on CH1), reference circuitry, temperature sensor, and all the

signal processing required to perform active power and energy

measurement.

The interrupt request output is an open drain, active low logic

output. The interrupt status register indicates the nature of the

interrupt, and the interrupt enable register controls which event

produces an output on the IRQ pin. The ADE7759 is available

in a 20-lead SSOP package.

An on-chip digital integrator allows direct interface to di/dt

current sensors such as a Rogowski coil. The digital integrator

eliminates the need for an external analog integrator and pro-

vides excellent long-term stability and precise phase matching

between the current and the voltage channels. The integrator

FUNCTIONAL BLOCK DIAGRAM

AV

DV

DD

DGND

DD

RESET

ADE7759

ZX

INTEGRATOR

dt

MULTIPLIER

V1P

V1N

ADC

LPF2

SAG

HPF1

APGAIN[11:0]

TEMP

SENSOR

APOS[15:0]

DFC

PHCAL[7:0]

V2P

V2N

ꢂ

ADC

CFNUM[11:0]

CFDEN[11:0]

CF

4kꢃ

REGISTERS AND

SERIAL INTERFACE

2.4V

REFERENCE

LPF1

AGND

REF

DIN DOUT SCLK

CLKIN CLKOUT

CS IRQ

IN/OUT

*U.S. Patents 5,745,323; 5,760,617; 5,862,069; 5,872,469; others pending.

REV. A

Information furnished by Analog Devices is believed to be accurate and

reliable. However, no responsibility is assumed by Analog Devices for its

use, norforanyinfringementsofpatentsorotherrightsofthirdpartiesthat

may result from its use. No license is granted by implication or otherwise

under any patent or patent rights of Analog Devices. Trademarks and

registered trademarks are the property of their respective companies.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781/329-4700

Fax: 781/326-8703

www.analog.com

ADE7759

TABLE OF CONTENTS

CHANNEL 1 ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Channel 1 ADC Gain Adjust . . . . . . . . . . . . . . . . . . . . . . 18

Channel 1 Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

CHANNEL 1 AND CHANNEL 2 WAVEFORM

SAMPLING MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 1

FUNCTIONAL BLOCK DIAGRAM . . . . . . . . . . . . . . . . . 1

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

TIMING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . 5

ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . 6

ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PIN CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . . 7

TERMINOLOGY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

MEASUREMENT ERROR . . . . . . . . . . . . . . . . . . . . . . . . . 8

PHASE ERROR BETWEEN CHANNELS . . . . . . . . . . . . . 8

POWER SUPPLY REJECTION . . . . . . . . . . . . . . . . . . . . . . 8

ADC OFFSET ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

GAIN ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

GAIN ERROR MATCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

TYPICAL PERFORMANCE CHARACTERISTICS (TPC) . . 9

TEST CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

ANALOG INPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

CHANNEL 2 ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Channel 2 Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

PHASE COMPENSATION . . . . . . . . . . . . . . . . . . . . . . . . 19

ACTIVE POWER CALCULATION . . . . . . . . . . . . . . . . . 20

ENERGY CALCULATION . . . . . . . . . . . . . . . . . . . . . . . . 21

Integration Time under Steady Load . . . . . . . . . . . . . . . . 22

POWER OFFSET CALIBRATION . . . . . . . . . . . . . . . . . . 22

ENERGY-TO-FREQUENCY CONVERSION . . . . . . . . . 22

LINE CYCLE ENERGY ACCUMULATION MODE . . . 24

CALIBRATING THE ENERGY METER . . . . . . . . . . . . . 24

Calculating the Average Active Power . . . . . . . . . . . . . . . 24

Calibrating the Frequency at CF . . . . . . . . . . . . . . . . . . . 25

Energy Meter Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

CLKIN FREQUENCY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

SUSPENDING THE ADE7759 FUNCTIONALITY . . . . 26

APPLICATION INFORMATION . . . . . . . . . . . . . . . . . . . 26

SERIAL INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Serial Write Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Serial Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

CHECKSUM REGISTER . . . . . . . . . . . . . . . . . . . . . . . . . 28

REGISTER DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . 30

Communications Register . . . . . . . . . . . . . . . . . . . . . . . . 30

Mode Register (06H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Interrupt Status Register (04H) . . . . . . . . . . . . . . . . . . . . 32

Reset Interrupt Status Register (05H) . . . . . . . . . . . . . . . 32

CH1OS Register (08H) . . . . . . . . . . . . . . . . . . . . . . . . . . 33

OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . 34

REVISION HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

di/dt CURRENT SENSOR AND DIGITAL

INTEGRATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

ZERO CROSSING DETECTION . . . . . . . . . . . . . . . . . . . 13

LINE VOLTAGE SAG DETECTION . . . . . . . . . . . . . . . . 14

Sag Level Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

POWER SUPPLY MONITOR . . . . . . . . . . . . . . . . . . . . . . 14

INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Using the ADE7759 Interrupts with an MCU . . . . . . . . . 15

Interrupt Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

TEMPERATURE MEASUREMENT . . . . . . . . . . . . . . . . 16

ANALOG-TO-DIGITAL CONVERSION . . . . . . . . . . . . . 16

Antialias Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

ADC Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Reference Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

–2–

REV. A

ADE7759

(AV_DD= DV_DD= 5 V ꢀ 5%, AGND = DGND = 0 V, On-Chip Reference, CLKIN = 3.579545 MHz XTAL,

T_MINto T_MAX= –40ꢁC to +85ꢁC, unless otherwise noted.)

SPECIFICATIONS¹

Parameter

Spec

Unit

Test Conditions/Comments

ENERGY MEASUREMENT ACCURACY

Measurement Bandwidth

14

kHz

CLKIN = 3.579545 MHz

Channel 2 = 300 mV rms/60 Hz, Gain = 1

Measurement Error¹on Channel 1

Channel 1 Range = 0.5 V Full-Scale

Gain = 1

Gain = 2

Gain = 4

Gain = 8

0.1

0.2

% typ

Over a Dynamic Range 1000 to 1

Gain = 16

Channel 1 Range = 0.25 V Full-Scale

Gain = 1

Gain = 2

Gain = 4

Gain = 8

0.1

0.2

% typ

Over a Dynamic Range 1000 to 1

Gain = 16

Channel 1 Range = 0.125 V Full-Scale

Gain = 1

Gain = 2

Gain = 4

Gain = 8

0.1

0.2

0.4

% typ

Over a Dynamic Range 1000 to 1

Gain = 16

Over a Dynamic Range 1000 to 1

Phase Error¹between Channels

AC Power Supply Rejection¹

Output Frequency Variation (CF)

±0.05 ∞ max

Line Frequency = 45 Hz to 65 Hz, HPF on

AV_DD= DV_DD= 5 V + 175 mV rms/120 Hz

Channel 1 = 20 mV rms/60 Hz, Gain = 16, Range = 0.5 V

Channel 2 = 300 mV rms/60 Hz, Gain = 1

AV_DD= DV_DD= 5 V ± 250 mV dc

0.2

% typ

DC Power Supply Rejection¹

Output Frequency Variation (CF)

±0.3

Channel 1 = 20 mV rms/60 Hz, Gain = 16, Range = 0.5 V

Channel 2 = 300 mV rms/60 Hz, Gain = 1

ANALOG INPUTS³

Maximum Signal Levels

Input Impedance (DC)

Bandwidth

±0.5

390

14

V max

kW min

kHz

V1P, V1N, V2N, and V2P to AGND

CLKIN/256, CLKIN = 3.579545 MHz

External 2.5 V Reference, Gain = 1 on Channels 1 and 2

Gain Error^{1, 3}

Channel 1

Range = 0.5 V Full-Scale

Range = 0.25 V Full-Scale

Range = 0.125 V Full-Scale

Channel 2

±4

% typ

V1 = 0.5 V dc

V1 = 0.25 V dc

V1 = 0.125 V dc

V2 = 0.5 V dc

Gain Error Match¹

Channel 1

External 2.5 V Reference

Range = 0.5 V Full-Scale

Range = 0.25 V Full-Scale

Range = 0.125 V Full-Scale

Channel 2

±0.3

% typ

Gain = 1, 2, 4, 8, 16

Offset Error¹

Channel 1

Channel 2

±20

mV max

Gain = 1

WAVEFORM SAMPLING

Channel 1

Sampling CLKIN/128, 3.579545 MHz/128 = 27.9 kSPS

See Channel 1 Sampling

Signal-to-Noise plus Distortion

Bandwidth (–3 dB)

Channel 2

62

14

dB typ

kHz

150 mV rms/60 Hz, Range = 0.5 V, Gain = 2

CLKIN = 3.579545 MHz

See Channel 2 Sampling

Signal-to-Noise plus Distortion

Bandwidth (–3 dB)

52

156

dB typ

Hz

150 mV rms/60 Hz, Gain = 2

CLKIN = 3.579545 MHz

–3–

REV. A

(continued)

ADE7759–SPECIFICATIONS

Parameter

Spec

Unit

Test Conditions/Comments

REFERENCE INPUT

REF_IN/OUTInput Voltage Range

2.6

2.2

10

V max

V min

pF max

2.4 V + 8%

2.4 V – 8%

Input Capacitance

ON-CHIP REFERENCE

Reference Error

Current Source

Output Impedance

Temperature Coefficient

Nominal 2.4 V at REF_IN/OUTPin

±200

10

4

mV max

mA max

kW min

20

ppm/∞C typ

CLKIN

Note All Specifications CLKIN of 3.579545 MHz

Input Clock Frequency

4

1

MHz max

MHz min

LOGIC INPUTS

RESET, DIN, SCLK, CLKIN, and CS

Input High Voltage, V_INH

Input Low Voltage, V_INL

Input Current, I_IN

2.4

0.8

±3

10

V min

DV_DD= 5 V ± 5%

V max

mA max

pF max

DV_DD= 5 V ± 5%

Typically 10 nA, V_IN= 0 V to DV_DD

Input Capacitance, C_IN

LOGIC OUTPUTS

SAG and IRQ

Output High Voltage, V_OH

Output Low Voltage, V_OL

ZX and DOUT

Open Drain Outputs, 10 kW pull-up resistor

I_SOURCE= 5 mA

I_SINK= 0.8 mA

4

0.4

V min

V max

Output High Voltage, V_OH

Output Low Voltage, V_OL

CF

4

0.4

V min

V max

I_SOURCE= 5 mA

I_SINK= 0.8 mA

Output High Voltage, V_OH

Output Low Voltage, V_OL

4

1

V min

V max

I_SOURCE= 5 mA

I_SINK= 7 mA

POWER SUPPLY

AV_DD

For Specified Performance

5 V – 5%

5 V + 5%

5 V – 5%

5 V + 5%

4.75

5.25

4.75

5.25

3

V min

V max

V min

V max

mA max

DV_DD

AI_DD

DI_DD

Typically 2.0 mA

Typically 3.0 mA

4

NOTES

¹See Terminology section for explanation of specifications.

²See plots in Typical Performance Characteristics.

³See Analog Inputs section.

Specifications subject to change without notice.

–4–

REV. A

ADE7759

(AV = DV = 5 V ꢀ 5%, AGND = DGND = 0 V, On-Chip Reference, CLKIN = 3.579545 MHz

XTAL, T_MINto T_MAX= –40ꢁC to +85ꢁC, unless otherwise noted.)

DD

TIMING CHARACTERISTICS^{1, 2}

Parameter

A, B Versions

Unit

Test Conditions/Comments

Write Timing

t₁

t₂

t₃

t₄

t₅

t₆

t₇

t₈

20

150

10

5

6.4

4

ns (min)

ms (min)

ns (min)

CS Falling Edge to First SCLK Falling Edge

SCLK Logic High Pulsewidth

SCLK Logic Low Pulsewidth

Valid Data Setup Time before Falling Edge of SCLK

Data Hold Time after SCLK Falling Edge

Minimum Time between the End of Data Byte Transfers

Minimum Time between Byte Transfers during a Serial Write

CS Hold Time after SCLK Falling Edge

100

Read Timing

t₉

4

ms (min)

Minimum Time between Read Command (i.e., a Write to Communications

Register) and Data Read

t₁₀

t₁₁

4

30

ms (min)

Minimum Time between Data Byte Transfers during a Multibyte Read

Data Access Time after SCLK Rising Edge following a Write to the Communica-

tions Register

3

ns (min)

4

t₁₂

100

10

100

ns (max)

ns (min)

ns (max)

ns (min)

Bus Relinquish Time after Falling Edge of SCLK

4

t₁₃

Bus Relinquish Time after Rising Edge of CS

10

NOTES

¹Sample tested during initial release and after any redesign or process change that may affect this parameter. All input signals are specified with tr = tf = 5 ns

(10% to 90%) and timed from a voltage level of 1.6 V.

²See Figures 2 and 3 and Serial Interface section of this data sheet.

³Measured with the load circuit in Figure 1 and defined as the time required for the output to cross 0.8 V or 2.4 V.

⁴Derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit in Figure 1. The measured number is then extrapolated back

to remove the effects of charging or discharging the 50 pF capacitor. This means that the time quoted in the timing characteristics is the true bus relinquish time of

the part and is independent of the bus loading.

I

200ꢂA

OL

TO

OUTPUT

2.1V

C

L

50pF

1.6mA

I

OH

Figure 1. Load Circuit for Timing Specifications

t₈

CS

t₂

t₆

t₁

t₃

t₇

SCLK

t₄

t₅

DIN

1

0

A4

A3

A2 A1

A0

DB7

DB0

DB7

DB0

COMMAND BYTE

MOST SIGNIFICANT BYTE

LEAST SIGNIFICANT BYTE

Figure 2. Serial Write Timing

CS

t₁

t₁₃

t₉

t₁₀

SCLK

DIN

0

A4

A3

A2 A1

A0

t₁₂

t₁₁

DOUT

DB0

DB7

DB0

DB7

COMMAND BYTE

MOST SIGNIFICANT BYTE

LEAST SIGNIFICANT BYTE

Figure 3. Serial Read Timing

–5–

REV. A

ADE7759

ABSOLUTE MAXIMUM RATINGS*

(T_A= 25∞C unless otherwise noted)

ORDERING GUIDE

Package Option*

Model

AV_DDto AGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V

DV_DDto DGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V

DV_DDto AV_DD. . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V

Analog Input Voltage to AGND

ADE7759ARS

RS-20

ADE7759ARSRL

EVAL-ADE7759EB

ADE7759 Evaluation Board

V1P, V1N, V2P, and V2N . . . . . . . . . . . . . . . . –6 V to +6 V

*RS = Shrink Small Outline Package in tubes; RSRL = Shrink Small

Outline Package in reel.

Reference Input Voltage to AGND . . –0.3 V to AV_DD+ 0.3 V

Digital Input Voltage to DGND . . . . –0.3 V to DV_DD+ 0.3 V

Digital Output Voltage to DGND . . . –0.3 V to DV_DD+ 0.3 V

Operating Temperature Range

Industrial (A, B Versions) . . . . . . . . . . . . . –40∞C to +85∞C

Storage Temperature Range . . . . . . . . . . . . –65∞C to +150∞C

Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150∞C

20-Lead SSOP, Power Dissipation . . . . . . . . . . . . . . . 450 mW

q

_JAThermal Impedance . . . . . . . . . . . . . . . . . . . . . 112∞C/W

Lead Temperature, Soldering

Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . 215∞C

Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . 220∞C

*Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. This is a stress rating only; functional operation of the

device at these or any other conditions above those listed in the operational

sections of this specification is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect device reliability.

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily

accumulate on the human body and test equipment and can discharge without detection. Although

the ADE7759 features proprietary ESD protection circuitry, permanent damage may occur on

devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are

recommended to avoid performance degradation or loss of functionality.

WARNING!

ESD SENSITIVE DEVICE

–6–

REV. A

ADE7759

PIN CONFIGURATION

1

2

20

19

18

17

16

15

14

13

12

RESET

DIN

DV

AV

DOUT

SCLK

CS

DD

3

4

V1P

V1N

5

ADE7759

CLKOUT

CLKIN

IRQ

TOP VIEW

6

V2N

(Not to Scale)

7

V2P

8

AGND

SAG

ZX

9

REF

IN/OUT

10

DGND

11 CF

PIN FUNCTION DESCRIPTIONS

Pin No.

Mnemonic

Description

1

RESET

Reset Pin for the ADE7759. A logic low on this pin will hold the ADCs and digital circuitry

(including the serial interface) in a reset condition.

2

3

DV_DD

AV_DD

Digital Power Supply. This pin provides the supply voltage for the digital circuitry in the ADE7759.

The supply voltage should be maintained at 5 V ± 5% for specified operation. This pin should be

decoupled to DGND with a 10 mF capacitor in parallel with a ceramic 100 nF capacitor.

Analog Power Supply. This pin provides the supply voltage for the analog circuitry in the ADE7759.

The supply should be maintained at 5 V ± 5% for specified operation. Every effort should be made

to minimize power supply ripple and noise at this pin by the use of proper decoupling method.

This pin should be decoupled to AGND with a 10 mF capacitor in parallel with a ceramic 100 nF

capacitor.

4, 5

V1P, V1N

Analog Inputs for Channel 1. This channel is intended for use with the di/dt current transducers

such as Rogowski coil, or other current sensors such as shunt or current transformer (CT). These

inputs are fully differential voltage inputs with maximum differential input signal levels of ±0.5 V,

±0.25 V, and ± 0.125 V, depending on the full-scale selection—see Analog Inputs section.

Channel 1 also has a PGA with gain selections of 1, 2, 4, 8, or 16. The maximum signal level at these

pins with respect to AGND is ±0.5 V. Both inputs have internal ESD protection circuitry. In addi-

tion, an overvoltage of ±6 V can be sustained on these inputs without risk of permanent damage.

6, 7

V2N, V2P

AGND

Analog Inputs for Channel 2. This channel is intended for use with the voltage transducer. These inputs

are fully differential voltage inputs with a maximum differential signal level of ±0.5 V. Channel 2

also has a PGA with gain selections of 1, 2, 4, 8, or 16. The maximum signal level at these pins

with respect to AGND is ±0.5 V. Both inputs have internal ESD protection circuitry, and an over-

voltage of ±6 V can be sustained on these inputs without risk of permanent damage.

This pin provides the ground reference for the analog circuitry in the ADE7759, i.e., ADCs and

reference. This pin should be tied to the analog ground plane or the quietest ground reference in

the system. This quiet ground reference should be used for all analog circuitry, e.g., antialiasing

filters, current and voltage transducers. To keep ground noise around the ADE7759 to a minimum,

the quiet ground plane should be connected to the digital ground plane at only one point. It is

acceptable to place the entire device on the analog ground plane—see Application Information section.

8

9

REF_IN/OUT

DGND

This pin provides access to the on-chip voltage reference. The on-chip reference has a nominal

value of 2.4 V ± 8% and a typical temperature coefficient of 20 ppm/∞C. An external reference

source may be connected at this pin. In either case, this pin should be decoupled to AGND with

a 1 mF capacitor in parallel with a 100 nF capacitor.

This provides the ground reference for the digital circuitry in the ADE7759, i.e., multiplier, filters,

and frequency output (CF). Because the digital return currents in the ADE7759 are small, it is

acceptable to connect this pin to the analog ground plane of the system—see Application Information

section. However, high bus capacitance on the DOUT pin may result in noisy digital current that

affects performance.

10

11

CF

Calibration Frequency Logic Output. The CF logic output gives Active Power information. This

output is intended to be used for operational and calibration purposes. The full-scale output fre-

quency can be adjusted by writing to the APGAIN, CFNUM, and CFDEN registers—see Energy

to Frequency Conversion section.

–7–

REV. A

ADE7759

PIN FUNCTION DESCRIPTIONS (continued)

Description

Pin No.

Mnemonic

12

ZX

Voltage Waveform (Channel 2) Zero Crossing Output. This output toggles logic high and low at

the zero crossing of the differential signal on Channel 2—see Zero Crossing Detection section.

13

14

15

SAG

This open-drain logic output goes active low when either no zero crossings are detected or a low

voltage threshold (Channel 2) is crossed for a specified duration—see Line Voltage Sag Detec-

tion section.

IRQ

Interrupt Request Output. This is an active low open-drain logic output. Maskable interrupts

include active energy register rollover, active energy register at half-full, zero crossing, SAG, and

arrivals of new waveform samples—see Interrupts section.

CLKIN

Master Clock for ADCs and Digital Signal Processing. An external clock can be provided at this

logic input. Alternatively, a parallel resonant AT crystal can be connected across CLKIN and

CLKOUT to provide a clock source for the ADE7759. The clock frequency for specified opera-

tion is 3.579545 MHz. Ceramic load capacitors of between 10 pF and 30 pF should be used with

the gate oscillator circuit. Refer to crystal manufacturer’s data sheet for load capacitance requirements.

16

CLKOUT

A crystal can be connected across this pin and CLKIN as described above to provide a clock source

for the ADE7759. The CLKOUT pin can drive one CMOS load when either an external clock is

supplied at CLKIN or a crystal is being used.

17

18

CS

Chip Select. Part of the 4-wire SPI serial interface. This active low logic input allows the ADE7759 to

share the serial bus with several other devices—see Serial Interface section.

SCLK

Serial Clock Input for the Synchronous serial interface. All serial data transfers are synchronized to

this clock—see Serial Interface section. The SCLK has a Schmitt-trigger input for use with a clock

source that has a slow edge transition time, e.g., opto-isolator outputs.

19

20

DOUT

DIN

Data Output for the Serial Interface. Data is shifted out at this pin on the rising edge of SCLK.

This logic output is normally in a high impedance state unless it is driving data onto the serial data

bus—see Serial Interface section.

Data Input for the Serial Interface. Data is shifted in at this pin on the falling edge of SCLK—see

Serial Interface section.

TERMINOLOGY

nominal supplies (5 V) is taken. A second reading is obtained

with the same input signal levels when the supplies are varied ±5%.

Any error introduced is again expressed as a percentage of reading.

MEASUREMENT ERROR

The error associated with the energy measurement made by the

ADE7759 is defined by the following formula:

ADC OFFSET ERROR

This refers to the dc offset associated with the analog inputs to

the ADCs. It means that with the analog inputs connected to

AGND, the ADCs still see a dc analog input signal. The magni-

tude of the offset depends on the gain and input range selection—see

Typical Performance Characteristics. However, when HPF1 is

switched on, the offset is removed from Channel 1 (current) and

the power calculation is not affected by this offset. The offsets

may be removed by performing an offset calibration—see Analog

Inputs section.

Percentage Error =

Energy registered by the ADE7759 –True Energy

True Energy

PHASE ERROR BETWEEN CHANNELS

The digital integrator and the HPF1 (High-Pass Filter) in

Channel 1 have nonideal phase response. To offset this phase

response and equalize the phase response between channels, two

phase correction networks are placed in Channel 1: one for the

digital integrator and the other for the HPF1. Each phase cor-

rection network corrects the phase response of the corresponding

component and ensures a phase match between Channel 1

(current) and Channel 2 (voltage) to within ±0.1∞ over a range

of 45 Hz to 65 Hz and ±0.2∞ over a range 40 Hz to 1 kHz.

GAIN ERROR

The gain error in the ADE7759 ADCs is defined as the difference

between the measured ADC output code (minus the offset)

and the ideal output code—see Channel 1 ADC and Channel

2 ADC. It is measured for each of the input ranges on Channel

1 (0.5 V, 0.25 V, and 0.125 V). The difference is expressed as a

percentage of the ideal code.

POWER SUPPLY REJECTION

This quantifies the ADE7759 measurement error as a percent-

age of reading when the power supplies are varied.

GAIN ERROR MATCH

The Gain Error Match is defined as the gain error (minus the

offset) obtained when switching between a gain of 1 (for each of

the input ranges) and a gain of 2, 4, 8, or 16. It is expressed as a

percentage of the output ADC code obtained under a gain of 1.

This gives the gain error observed when the gain selection is

changed from 1 to 2, 4, 8, or 16.

For the ac PSR measurement, a reading at nominal supplies

(5 V) is taken. A second reading is obtained with the same input

signal levels when an ac (175 mV rms/120 Hz) signal is intro-

duced onto the supplies. Any error introduced by this ac signal

is expressed as a percentage of reading—see Measurement Error

definition above. For the dc PSR measurement a reading at

–8–

REV. A

Typical Performance Characteristics–ADE7759

0.5

0.4

0.5

FULL SCALE = 0.5V

0.4

GAIN = 1

INTEGRATOR OFF

INTERNAL REFERENCE

–40ꢀC, PF = 1

0.3

0.2

0.3

+85ꢀC, PF = 1

+85ꢀC, PF = 0.5

0.2

0.1

–40ꢀC, PF = 0.5

0.1

0.0

–0.1

–0.2

–0.3

–0.4

–0.5

–0.1

–0.2

–0.3

–0.4

–0.5

+25ꢀC, PF = 1

+25ꢀC, PF = 0.5

+25ꢀC, PF = 1

FULL SCALE = 0.5V

GAIN = 1

INTEGRATOR OFF

INTERNAL REFERENCE

0.01

0.1

1

10

100

0.01

0.1

1

10

100

CURRENT – A

TPC 1. Error as a % of Reading

TPC 4. Error as a % of Reading

0.5

0.4

0.5

0.4

FULL SCALE = 0.5V

GAIN = 1

INTEGRATOR OFF

EXTERNAL REFERENCE

–40ꢀC, PF = 1

+25ꢀC, PF = 1

–40ꢀC, PF = 0.5

0.3

0.2

0.3

0.2

+25ꢀC, PF = 1

0.1

0.0

–0.1

–0.2

–0.3

–0.4

–0.5

–0.1

–0.2

–0.3

–0.4

–0.5

+25ꢀC, PF = 0.5

+85ꢀC, PF = 1

+85ꢀC, PF = 0.5

FULL SCALE = 0.5V

GAIN = 1

INTEGRATOR OFF

EXTERNAL REFERENCE

0.01

0.1

1

10

100

0.01

0.1

1

10

CURRENT – A

TPC 2. Error as a % of Reading

TPC 5. Error as a % of Reading

0.5

0.4

0.5

0.4

+85ꢀC, PF = 0.5

–40ꢀC, PF = 1

0.3

0.2

0.3

0.2

–40ꢀC, PF = 0.5

+25ꢀC, PF = 1

0.1

+85ꢀC, PF = 1

0.0

–0.1

–0.2

–0.3

–0.4

–0.5

–0.1

–0.2

–0.3

–0.4

–0.5

+25ꢀC, PF = 1

FULL SCALE = 0.5V

GAIN = 4

INTEGRATOR OFF

INTERNAL REFERENCE

FULL SCALE = 0.5V

GAIN = 4

INTEGRATOR OFF

+25ꢀC, PF = 0.5

INTERNAL REFERENCE

0.01

0.1

1

10

100

0.01

0.1

1

10

CURRENT – A

TPC 3. Error as a % of Reading

TPC 6. Error as a % of Reading

–9–

REV. A

ADE7759

0.5

0.4

FULL SCALE = 0.5V

GAIN = 4

0.4

+85ꢀC, PF = 0.5

INTEGRATOR OFF

EXTERNAL REFERENCE

0.3

0.2

0.3

0.2

–40ꢀC, PF = 1

+25ꢀC, PF = 1

0.1

0.0

–40ꢀC, PF = 0.5

–0.1

–0.2

–0.1

–0.2

–0.3

–0.4

–0.5

+85ꢀC, PF = 1

+25ꢀC, PF = 0.5

FULL SCALE = 0.5V

GAIN = 4

INTEGRATOR OFF

EXTERNAL REFERENCE

–0.3

–0.4

–0.5

0.01

0.1

1

10

100

0.01

0.1

1

10

100

CURRENT – A

TPC 7. Error as a % of Reading

TPC 10. Error as a % of Reading

1.5

1.3

1.1

0.9

0.7

0.5

0.4

FULL SCALE = 0.5V

GAIN = 4

INTEGRATOR ON

INTERNAL REFERENCE

0.3

0.2

–40ꢀC, PF = 1

+25ꢀC, PF = 1

0.1

–40ꢀC, PF = 0.5

0.5

0.3

0.0

+85ꢀC, PF = 0.5

+25ꢀC, PF = 1

–0.1

–0.2

–0.3

–0.4

–0.5

+85ꢀC, PF = 1

0.1

FULL SCALE = 0.5V

GAIN = 4

INTEGRATOR ON

–0.1

–0.3

–0.5

+25ꢀC, PF = 0.5

INTERNAL REFERENCE

0.01

0.1

1

10

100

0.01

0.1

1

10

100

CURRENT – A

TPC 8. Error as a % of Reading

TPC 11. Error as a % of Reading

0.5

0.4

1.5

1.3

1.1

0.9

0.7

FULL SCALE = 0.5V

GAIN = 4

INTEGRATOR ON

FULL SCALE = 0.5V

GAIN = 4

INTEGRATOR ON

EXTERNAL REFERENCE

0.3

0.2

EXTERNAL REFERENCE

–40ꢀC, PF = 1

+85ꢀC, PF = 0.5

+25ꢀC, PF = 1

0.1

0.0

0.5

0.3

–40ꢀC, PF = 0.5

–0.1

–0.2

+25ꢀC, PF = 1

0.1

+85ꢀC, PF = 1

–0.3

–0.4

–0.5

–0.1

–0.3

–0.5

+25ꢀC, PF = 0.5

0.01

0.1

1

10

100

0.01

0.1

1

10

100

CURRENT – A

TPC 9. Error as a % of Reading

TPC 12. Error as a % of Reading

–10–

REV. A

ADE7759

Test Circuits

V

DD

I

100nF

RESET

DD

10ꢄF

100nF

AV

100nF

RESET

DD

10ꢄF

I

di/dt CURRENT

SENSOR

AV

DV

DD

DIN

1kꢃ

100ꢃ 1kꢃ

33nF 33nF

100ꢃ 1kꢃ

V1P

TO SPI BUS

(USED ONLY FOR

CALIBRATION)

33nF

DOUT

SCLK

CS

TO SPI BUS

(USED ONLY FOR

CALIBRATION)

DOUT

SCLK

CS

RB

1kꢃ

V1N

U1

33nF

ADE7759

CLKOUT

Y1

22pF

Y1

V2N

3.58MHz

1kꢃ 33nF

600kꢃ

1kꢃ

33nF

CLKIN

22pF

600kꢃ

1kꢃ

V2P

IRQ

SAG

ZX

IRQ

SAG

ZX

33nF

110V

1kꢃ

110V

NOT CONNECTED

REF

IN/OUT

U3

CF

100nF

U3

10ꢄF

CF

100nF

10ꢄF

AGND DGND

TO

FREQUENCY

COUNTER

TO

FREQUENCY

COUNTER

CT TURN RATIO = 1800:1

CHANNEL 2 GAIN = 1

CHANNEL 1 GAIN = 4

CHANNEL 2 GAIN = 1

GAIN (CH1)

RB

1

4

10ꢃ

2.5ꢃ

PS2501-1

Test Circuit 1. Performance Curve (Integrator OFF)

Test Circuit 2. Performance Curve (Integrator ON)

ANALOG INPUTS

In addition to the PGA, Channel 1 also has a full-scale input

range selection for the ADC. The ADC analog input range

selection is also made using the gain register—see Figure 5. As

mentioned previously the maximum differential input voltage is

0.5 V. However, by using Bits 3 and 4 in the gain register, the

maximum ADC input voltage can be set to 0.5 V, 0.25 V, or

0.125 V. This is achieved by adjusting the ADC reference—see

Reference Circuit section. Table I summarizes the maximum

differential input signal level on Channel 1 for the various ADC

range and gain selections.

The ADE7759 has two fully differential voltage input channels.

The maximum differential input voltage for input pairs V1P/V1N

and V2P/V2N are 0.5 V. In addition, the maximum signal

level on analog inputs for V1P/V1N and V2P/V2N are 0.5 V

with respect to AGND.

Each analog input channel has a PGA (Programmable Gain

Amplifier) with possible gain selections of 1, 2, 4, 8, and 16. The

gain selections are made by writing to the gain register—see

Figure 5. Bits 0 to 2 select the gain for the PGA in Channel 1 and

the gain selection for the PGA in Channel 2 is made via Bits 5

to 7. Figure 4 shows how a gain selection for Channel 1

is made using the gain register.

Table I. Maximum Input Signal Levels for Channel 1

Max Signal

Channel 1

ADC Input Range Selection

0.5 V

0.25 V

0.125 V

GAIN[7:0]

0.5 V

0.25 V

Gain = 1

Gain = 2

Gain = 4

Gain = 8

Gain = 16

Gain = 1

Gain = 2

Gain = 4

Gain = 8

Gain = 16

0.125 V

0.0625 V

0.0313 V

0.0156 V

0.00781 V

Gain = 1

Gain = 2

Gain = 4

Gain = 8

Gain = 16

GAIN (K)

SELECTION

V1P

V

IN

K ꢅ V

IN

GAIN REGISTER*

CHANNEL 1 AND CHANNEL 2 PGA CONTROL

V1N

7

6

5

4

3

2

1

0

+

0

ADDR:

0AH

OFFSET ADJUST

(ꢁ50mV)

PGA 2 GAIN SELECT

000 = ꢅ1

PGA 1 GAIN SELECT

000 = ꢅ1

001 = ꢅ2

010 = ꢅ4

CH1OS[7:0]

011 = ꢅ8

BIT 0 to 5: SIGN MAGNITUDE CODED OFFSET CORRECTION

BIT 6: NOT USED

BIT 7: DIGITAL INTEGRATOR (ON = 1, OFF = 0; DEFAULT ON)

100 = ꢅ16

CHANNEL 1 FULL-SCALE SELECT

00 = 0.5V

01 = 0.25V

10 = 0.125V

*REGISTER CONTENTS

SHOW POWER-ON DEFAULTS

Figure 4. PGA in Channel 1

Figure 5. Analog Gain Register

REV. A

–11–

ADE7759

CH1OS[5:0]

It is also possible to adjust offset errors on Channel 1 and

Channel 2 by writing to the offset correction registers (CH1OS

and CH2OS, respectively). These registers allow channel

offsets in the range 24 mV to 50 mV (depending on the

gain setting) to be removed. Note that it is not necessary to

perform an offset correction in an energy measurement applica-

tion if HPF1 Channel 1 is switched on. Figure 6 shows the

effect of offsets on the real power calculation; an offset on

Channel 1 and Channel 2 will contribute a dc component

after multiplication. Since this dc component is extracted by

LPF2 to generate the active (real) power information, the

offsets will have contributed an error to the active power

calculation. This problem is easily avoided by enabling HPF1

in Channel 1. By removing the offset from at least one channel,

no error component is generated at dc by the multiplication.

Error terms at cos(ω t) are removed by LPF2 and by integra-

tion of the active power signal in the active energy register

(AENERGY[39:0])—see Energy Calculation section.

SIGN + 5 BITS

01,1111b

1Fh

00h

0mV

–50mV

+50mV

OFFSET

ADJUST

11,1111b

SIGN + 5 BITS

3Fh

Figure 7. Channel Offset Correction Range (Gain = 1)

di/dt CURRENT SENSOR AND DIGITAL INTEGRATOR

The di/dt sensor detects changes in magnetic field caused by ac

current. Figure 8 shows the principle of a di/dt current sensor.

DC COMPONENT (INCLUDING ERROR TERM)

IS EXTRACTED BY THE LPF FOR REAL

POWER CALCULATION

MAGNETIC FIELD CREATED BY CURRENT

(DIRECTLY PROPORTIONALTO CURRENT)

V

ꢅ I

OS

V ꢅ I

2

EMF (ELECTROMOTIVE FORCE)

+

I

ꢅ V

ꢅ I

OS

INDUCED BY CHANGES IN

–

MAGNETIC FLUX DENSITY (di/dt)

V

OS

ꢆ

2ꢆ

0

Figure 8. Principle of a di/dt Current Sensor

Figure 6. Effect of Channel Offsets on the Real

Power Calculation

The flux density of a magnetic field induced by a current is directly

proportional to the magnitude of the current. The changes in the

magnetic flux density passing through a conductor loop generate

an electromotive force (EMF) between the two ends of the loop.

The EMF is a voltage signal that is proportional to the di/dt of

the current. The voltage output from the di/dt current sensor

is determined by the mutual inductance between the current-

carrying conductor and the di/dt sensor. Figure 9 shows that

the mutual inductance produces a di/dt signal at the output

of the sensor.

The contents of the offset correction registers are 6-bit, sign and

magnitude coded. The weighting of the LSB size depends on

the gain setting, i.e., 1, 2, 4, 8, or 16. Table II shows the

correctable offset span for each of the gain settings and the LSB

weight (mV) for the offset correction registers. The maximum

value that can be written to the offset correction registers is 31

decimal—see Figure 7.

Table II. Offset Correction Range

MUTUAL INDUCTANCE M

Gain

Correctable Span

LSB Size

1

2

4

8

50 mV

37 mV

30 mV

26 mV

24 mV

1.61 mV/LSB

1.19 mV/LSB

0.97 mV/LSB

0.84 mV/LSB

0.77 mV/LSB

+

di(t)

dt

i(t)

v = M ꢅ

–

16

Figure 9. Mutual Inductance Between the di/dt

Sensor and the Current Carrying Conductor

Figure 7 shows the relationship between the offset correction

register contents and the offset (mV) on the analog inputs for a

gain setting of one. To perform an offset adjustment, the analog

inputs should be first connected to AGND, and there should be

no signal on either Channel 1 or Channel 2. A read from

Channel 1 or Channel 2 using the waveform register will give an

indication of the offset in the channel. This offset can be

canceled by writing an equal but opposite offset value to the

relevant offset register. The offset correction can be confirmed

by performing another read. Note that when adjusting the offset of

Channel 1, the digital integrator and the HPF1 should be disabled.

The current signal needs to be recovered from the di/dt signal

before it can be used for active power calculation. An integrator

is therefore necessary to restore the signal to its original form.

The ADE7759 has a built-in digital integrator to recover the

current signal from the di/dt sensor. The digital integrator on

Channel 1 is switched on by default when the ADE7759 is

powered up. Setting the MSB of the CH1OS register to 0 will

turn off the integrator. Figures 10 to 13 show the magnitude

and phase response of the digital integrator.

–12–

REV. A

ADE7759

30

20

–89.980

–89.985

–89.990

–89.995

–90.000

–90.005

–90.010

10

0

–10

–20

–30

–40

–50

–60

–90.015

–90.020

1

2

3

4

10

40

45

50

55

60

65

70

10

FREQUENCY – Hz

Figure 10. Gain Response of the Digital Integrator

Figure 13. Phase Response of the Digital Integrator

(40 Hz to 70 Hz)

–88.0

–88.5

Note that the integrator has a –20 dB/dec attenuation and

approximately –90° phase shift. When combined with a di/dt

sensor, the resulting magnitude and phase response should be a

flat gain over the frequency band of interest. However, the di/dt

sensor has a 20 dB/dec gain associated with it, and generates

significant high frequency noise. A more effective antialiasing

filter is needed to avoid noise due to aliasing—see Antialias

Filter section.

–89.0

–89.5

–90.0

–90.5

When the digital integrator is switched off, the ADE7759 can be

used directly with a conventional current sensor such as current

transformer (CT) or a low resistance current shunt.

–91.0

–91.5

–92.0

ZERO CROSSING DETECTION

1

2

3

4

10

FREQUENCY – Hz

The ADE7759 has a zero crossing detection circuit on Channel 2.

This zero crossing is used to produce an external zero cross

signal (ZX), and it is also used in the calibration mode—see

Energy Calibration section. The zero crossing signal is also used

to initiate a temperature measurement on the ADE7759—see

Temperature Measurement section. Figure 14 shows how the

zero cross signal is generated from the output of LPF1.

Figure 11. Phase Response of the Digital Integrator

0

–1

–2

–3

–4

–5

–6

ꢅ1, ꢅ2, ꢅ4,

ꢅ8, ꢅ16

REFERENCE

V2P

V2N

{GAIN [7:5]}

–63%TO +63% FS

1

TO

PGA2

ADC 2

V2

MULTIPLIER

ZERO

CROSS

ZX

LPF1

f_–3dB= 156Hz

21.04ꢀ @ 60Hz

40

45

50

55

60

65

70

1.0

0.93

FREQUENCY – Hz

ZX

Figure 12. Gain Response of the Digital Integrator

(40 Hz to 70 Hz)

LPF1

V2

Figure 14. Zero Cross Detection on Channel 2

REV. A

–13–

ADE7759

The ZX signal will go logic high on a positive going zero crossing

and logic low on a negative going zero crossing on Channel 2.

The zero crossing signal ZX is generated from the output of

LPF1. LPF1 has a single pole at 156 Hz (CLKIN = 3.579545 MHz).

As a result, there will be a phase lag between the analog input

signal V2 and the output of LPF1. The phase response of this

filter is shown in the Channel 2 Sampling section. The phase

lag response of LPF1 results in a time delay of approximately

0.97 ms (@ 60 Hz) between the zero crossing on the analog

inputs of Channel 2 and the rising or falling edge of ZX.

The SAG pin will go logic high again when the absolute value of

the signal on Channel 2 exceeds the sag level set in the Sag

Level register. This is shown in Figure 15 when the SAG pin

goes high during the tenth half cycle from the time when the

signal on Channel 2 first dropped below the threshold level.

Sag Level Set

The contents of the sag level register (1 byte) are compared to

the absolute value of the most significant byte output from

LPF1, after it is shifted left by one bit. For example, the nomi-

nal maximum code from LPF1 with a full-scale signal on

Channel 2 is 257F6h or (0010, 0101, 0111, 1111, 0110b)—see

Channel 2 Sampling section. Shifting one bit left will give 0100,

1010, 1111, 1110, 1100b, or 4AFECh. Therefore, writing 4Ah

to the sag level register will put the sag detection level at full

scale. Writing 00h will put the sag detection level at zero. The

sag level register is compared to the most significant byte of a

waveform sample after the shift left, and detection is made when

the contents of the sag level register are greater.

The zero crossing detection also has an associated timeout reg-

ister, ZXTOUT. This unsigned, 12-bit register is decremented

1 LSB every 128/CLKIN seconds. The register is reset to its

user-programmed full-scale value every time a zero crossing on

Channel 2 is detected. The default power-on value in this regis-

ter is FFFh. If the register decrements to zero before a zero

crossing is detected and the DISSAG bit in the mode register is

logic zero, the SAG pin will go active low. The absence of a zero

crossing is also indicated on the IRQ output if the SAG Enable

bit in the interrupt enable register is set to Logic 1. Irrespective

of the enable bit setting, the SAG flag in the interrupt status

register is always set when the ZXTOUT register is decremented

to zero—see Interrupts section. The zero cross timeout register

can be written/read by the user and has an address of 0Eh—see

Serial Interface section. The resolution of the register is 128/CLKIN

seconds per LSB. Thus the maximum delay for an interrupt

is 0.15 second (128/CLKIN × 2¹²).

POWER SUPPLY MONITOR

The ADE7759 also contains an on-chip power supply monitor.

The analog supply (AV_DD) is continuously monitored by the

ADE7759. If the supply is less than 4 V 5%, the ADE7759

will go into an inactive state, i.e., no energy will be accumulated

when the supply voltage is below 4 V. This is useful to ensure

correct device operation at power-up and during power-down.

The power supply monitor has built-in hysteresis and filtering.

This gives a high degree of immunity to false triggering due to

noisy supplies.

LINE VOLTAGE SAG DETECTION

In addition to the detection of the loss of the line voltage signal

(zero crossing), the ADE7759 can also be programmed to detect

when the absolute value of the line voltage drops below a certain

peak value, for a number of half cycles. This condition is illus-

trated in Figure 15.

AV

DD

5V

4V

CHANNEL 2

FULL SCALE

0V

TIME

SAGLVL [7:0]

ADE7759

POWER-ON

RESET

INACTIVE

ACTIVE

INACTIVE

SAG RESET HIGH

WHEN CHANNEL 2

EXCEEDS SAGLVL [7:0]

SAG

SAGCYC [7:0] = 06H

6 HALF CYCLES

SAG

Figure 16. On-Chip Power Supply Monitor

As seen in Figure 16, the trigger level is nominally set at 4 V.

The tolerance on this trigger level is about 5%. The SAG pin

can also be used as a power supply monitor input to the MCU.

The SAG pin will go logic low when the ADE7759 is reset. The

power supply and decoupling for the part should be such that

the ripple at AV_DDdoes not exceed 5 V 5% as specified for

normal operation.

Figure 15. Sag Detection

Figure 15 shows the line voltage fall below a threshold that is set

in the sag level register (SAGLVL[7:0]) for nine half cycles.

Since the sag cycle register (SAGCYC[7:0]) contains 06h, the

SAG pin will go active low at the end of the sixth half cycle for

which the line voltage falls below the threshold, if the DISSAG

bit in the mode register is Logic 0. As is the case when zero

crossings are no longer detected, the sag event is also recorded

by setting the SAG flag in the interrupt status register. If the

SAG enable bit is set to Logic 1, the IRQ logic output will go

active low—see Interrupts section.

Bit 6 of the interrupt status register (STATUS[7:0]) will be set

to logic high upon power-up or every time the analog supply

(AV_DD) dips below the power supply monitor threshold (4 V 5%)

and recovers. However, no interrupt can be generated because

the corresponding bit (Bit 6) in the interrupt enable register

(IRQEN[7:0]) is not active—see Interrupts section.

–14–

REV. A

ADE7759

INTERRUPTS

MCU should be configured to start executing its Interrupt Ser-

vice Routine (ISR). On entering the ISR, all interrupts should

be disabled using the global interrupt enable bit. At this point,

the MCU external interrupt flag can be cleared to capture inter-

rupt events that occur during the current ISR.

ADE7759 interrupts are managed through the interrupt status

register (STATUS[7:0]) and the interrupt enable register

(IRQEN[7:0]). When an interrupt event occurs in the ADE7759,

the corresponding flag in the status register is set to a Logic 1—see

Interrupt Status Register section. If the enable bit for this

interrupt in the interrupt enable register is Logic 1, then the

IRQ logic output goes active low. The flag bits in the status

register are set irrespective of the state of the enable bits.

When the MCU interrupt flag is cleared, a read from the status

register with reset is carried out. This will cause the IRQ line to

be reset logic high (t₂)—see Interrupt Timing section. The

status register contents are used to determine the source of

the interrupt(s), and thus the appropriate action will be taken. If

a subsequent interrupt event occurs during the ISR, that event

will be recorded by the MCU external interrupt flag being set

again (t₃). On returning from the ISR, the global interrupt mask

will be cleared (same instruction cycle) and the external inter-

rupt flag will cause the MCU to jump to its ISR once again. This

will ensure that the MCU does not miss any external interrupts.

To determine the source of the interrupt, the system master

(MCU) should perform a read from the status register with

reset (RSTATUS[7:0]). This is achieved by carrying out a

read from address 05h. The IRQ output will go logic high on

completion of the interrupt status register read command—

see Interrupt Timing section. When carrying out a read with

reset, the ADE7759 is designed to ensure that no interrupt

events are missed. If an interrupt event occurs just as the status

register is being read, the event will not be lost and the IRQ

logic output is guaranteed to go high for the duration of the

interrupt status register data transfer before going logic low

again to indicate the pending interrupt. See the following

section for a more detailed description.

Interrupt Timing

The Serial Interface section should be reviewed first, before the

Interrupt Timing section. As previously described, when the

IRQ output goes low, the MCU ISR must read the interrupt

status register to determine the source of the interrupt. When

reading the status register contents, the IRQ output is set high

on the last falling edge of SCLK of the first byte transfer (read

interrupt status register command). The IRQ output is held

high until the last bit of the next 8-bit transfer is shifted out

(interrupt status register contents)—see Figure 18. If an inter-

rupt is pending at this time, the IRQ output will go low again. If

no interrupt is pending, the IRQ output will stay high.

Using the ADE7759 Interrupts with an MCU

Figure 17 shows a timing diagram with a suggested implementa-

tion of ADE7759 interrupt management using an MCU. At

time t₁, the IRQ line will go active low, indicating that one or

more interrupt events have occurred in the ADE7759. The IRQ

logic output should be tied to a negative edge-triggered external

interrupt on the MCU. On detection of the negative edge, the

MCU

INTERRUPT

FLAG SET

t₁

t₂

t₃

IRQ

ISR ACTION

(BASED ON

STATUS CONTENTS)

ISR RETURN

GLOBAL INTERRUPT

MASK RESET

JUMP

TO

ISR

GLOBAL

INTERRUPT

MASK SET

CLEAR MCU

INTERRUPT

FLAG

READ

STATUS WITH

RESET (05h)

JUMP

TO

ISR

MCU

PROGRAM

SEQUENCE

Figure 17. Interrupt Management

CS

t₁

SCLK

t₉

0

1

0

1

DIN

t₁₁

DB7

DB0

DOUT

READ STATUS REGISTER COMMAND

STATUS REGISTER CONTENTS

IRQ

Figure 18. Interrupt Timing

REV. A

–15–

ADE7759

TEMPERATURE MEASUREMENT

the signal is sampled at a rate (frequency) that is many times

higher than the bandwidth of interest. For example, the sam-

pling rate in the ADE7759 is CLKIN/4 (894 kHz) and the band

of interest is 40 Hz to 2 kHz. Oversampling has the effect of

spreading the quantization noise (noise due to sampling) over a

wider bandwidth. With the noise spread more thinly over a

wider bandwidth, the quantization noise in the band of interest

is lowered—see Figure 20. However, oversampling alone is not

an efficient enough method to improve the signal-to-noise ratio

(SNR) in the band of interest. For example, an oversampling

ratio of 4 is required just to increase the SNR by only 6 dB (one

bit). To keep the oversampling ratio at a reasonable level, it is

possible to shape the quantization noise so that the majority of

the noise lies at the higher frequencies. This is what happens in

the sigma-delta modulator: the noise is shaped by the integrator,

which has a high-pass type response for the quantization noise.

The result is that most of the noise is at the higher frequencies,

where it can be removed by the digital low-pass filter. This noise

shaping is also shown in Figure 20.

ADE7759 also includes an on-chip temperature sensor. A

temperature measurement can be made by setting Bit 5 in the

mode register. When Bit 5 is set logic high in the mode register, the

ADE7759 will initiate a temperature measurement on the next

zero crossing. When the zero crossing on Channel 2 is de-

tected, the voltage output from the temperature sensing

circuit is connected to ADC1 (Channel 1) for digitizing. The

resultant code is processed and placed in the temperature

register (TEMP[7:0]) approximately 26 µs later (24 CLKIN

cycles). If enabled in the interrupt enable register (Bit 5), the

IRQ output will go active low when the temperature conversion

is finished. Note that temperature conversion will introduce a

small amount of noise in the energy calculation. If temperature

conversion is performed frequently (i.e., multiple times per sec-

ond), a noticeable error will accumulate in the resulting energy

calculation over time.

The contents of the temperature register are signed (twos

complement) with a resolution of approximately 1 LSB/°C. The

temperature register will produce a code of 00h when the ambient

temperature is approximately 70°C. The temperature mea-

surement is uncalibrated in the ADE7759 and has an offset

tolerance that could be as high as 20°C.

ANTIALIAS

FILTER (RC)

DIGITAL

FILTER

SAMPLING

FREQUENCY

SIGNAL

SHAPED

NOISE

ANALOG-TO-DIGITAL CONVERSION

The analog-to-digital conversion in the ADE7759 is carried out

using two second-order sigma-delta ADCs. The block diagram in

Figure 19 shows a first-order (for simplicity) sigma-delta ADC.

The converter is made up of two parts, first the sigma-delta modu-

lator and second the digital low-pass filter.

0

2

447

FREQUENCY – kHz

894

HIGH RESOLUTION

SIGNAL

OUTPUT FROM DIGITAL

LPF

A sigma-delta modulator converts the input signal into a con-

tinuous serial stream of 1s and 0s at a rate determined by the

sampling clock. In the ADE7759, the sampling clock is equal to

CLKIN/4. The 1-bit DAC in the feedback loop is driven by the

serial data stream. The DAC output is subtracted from the input

signal. If the loop gain is high enough, the average value of the

DAC output (and therefore the bit stream) will approach that

of the input signal level. For any given input value in a single

sampling interval, the data from the 1-bit ADC is virtually

meaningless. Only when a large number of samples are averaged

will a meaningful result be obtained. This averaging is carried

out in the second part of the ADC, the digital low-pass filter. By

averaging a large number of bits from the modulator, the low-

pass filter can produce 20-bit datawords that are proportional to

the input signal level.

NOISE

0

2

447

894

FREQUENCY – kHz

Figure 20. Noise Reduction Due to Oversampling

and Noise Shaping in the Analog Modulator

Antialias Filter

Figure 19 also shows an analog low-pass filter (RC) on the input

to the modulator. This filter is present to prevent aliasing.

Aliasing is an artifact of all sampled systems. Basically, it means

that frequency components in the input signal to the ADC that

are higher than half the sampling rate of the ADC will appear in

the sampled signal at a frequency below half the sampling rate.

Figure 21 illustrates the effect. Frequency components above

half the sampling frequency (also known as the Nyquist frequency,

i.e., 447 kHz) get imaged or folded back down below 447 kHz.

This will happen with all ADCs regardless of the architecture.

In the example shown, it can be seen that only frequencies near

the sampling frequency (894 kHz) will move into the band of

interest for metering, i.e., 40 Hz–2 kHz. This allows us to use a

very simple LPF (low-pass filter) to attenuate these high fre-

quencies (near 900 kHz) and to prevent distortion in the band

of interest. For a conventional current sensor, a simple RC filter

(single pole) with a corner frequency of 10 kHz will produce an

attenuation of approximately 40 dB at 894 kHz—see Figure 20.

The 20 dB per decade attenuation is usually sufficient to elimi-

nate the effects of aliasing for a conventional current sensor.

MCLK/4

ANALOG

DIGITAL

LOW-PASS FILTER

LOW-PASS

LATCHED

COMPARATOR

FILTER

+

R

+

–

1

20

∫

–

C

V

REF

.....10100101.....

1-BIT DAC

Figure 19. First Order Sigma-Delta (Σ-∆) ADC

The sigma-delta converter uses two techniques to achieve high

resolution from what is essentially a one-bit conversion tech-

nique. The first is oversampling. By oversampling we mean that

–16–

REV. A

ADE7759

OUTPUT

IMPEDANCE

6kꢃ

ALIASING EFFECTS

MAXIMUM

LOAD = 10ꢄA

REF

SAMPLING

FREQUENCY

IN/OUT

2.42V

IMAGE

FREQUENCIES

PTAT

60ꢄA

2.5V

1.7kꢃ

12.5kꢃ

0

2

447

894

FREQUENCY – kHz

REFERENCE INPUT

12.5kꢃ

Figure 21. ADC and Signal Processing in Channel 1

TO ADC CHANNEL 1

(RANGE SELECT)

2.42V, 1.21V, 0.6V

For a di/dt sensor such as a Rogowski coil, however, the sensor

has 20 dB per decade gain. This will neutralize the –20 dB per

decade attenuation produced by this simple LPF and nullifies

the antialias filter. Therefore, when using a di/dt sensor, mea-

sures should be taken to offset the 20 dB per decade gain coming

from the di/dt sensor and produce sufficient attenuation to

eliminate any aliasing effect. One simple approach is to cascade

two RC filters to produce –40 dB per decade attenuation. The

transfer function for a cascaded filter is the following:

Figure 22. ADC and Reference Circuit Output

The REF_IN/OUTpin can be overdriven by an external source,

e.g., an external 2.5 V reference. Note that the nominal refer-

ence value supplied to the ADCs is now 2.5 V not 2.42 V. This

has the effect of increasing the nominal analog input signal

range by 2.5/2.42 ϫ 100% = 3%, or from 0.5 V to 0.5165 V.

The internal voltage reference on the ADE7759 has a tempera-

ture drift associated with it—see ADE7759 Specifications section

for the temperature coefficient specification (in ppm°C). The

value of the temperature drift varies slightly from part to part.

Since the reference is used for the ADCs in both Channel 1 and 2,

any x% drift in the reference will result in 2x% deviation of the

meter reading. The reference drift resulting from temperature

changes is usually very small, and it is typically much smaller

than the drift of other components on a meter. However, if

guaranteed temperature performance is needed, one needs to

use an external voltage reference. Alternatively, the meter can be

calibrated at multiple temperatures. Real-time compensation

can be achieved easily using the on-chip temperature sensor.

1

H(s) =

1+ sR1C1+ sR2C2 + sR1C2 + s²R1C1R2C2

where R1C1 represents the RC used in the first stage of the

cascade and R2C2 in that of the second stage. The s²term in the

transfer function produces a –40 dB/decade attenuation. Note

that to minimize the measurement error, especially at low power

factor, it is important to match the phase angle between the

voltage and the current channel. The small phase mismatch in

the external antialias filter can be corrected using the phase calibra-

tion register (PHCAL[7:0])—see Phase Compensation section.

ADC Transfer Function

Below is an expression which relates the output of the LPF in

the sigma-delta ADC to the analog input signal level. Both ADCs

in the ADE7759 are designed to produce the same output code

for the same input signal level.

CHANNEL 1 ADC

Figure 23 shows the ADC and signal processing chain for Chan-

nel 1. In waveform sampling mode, the ADC outputs a signed

twos complement 20-bit dataword at a maximum of 27.9 kSPS

(CLKIN/128). The output of the ADC can be scaled by 50%

to perform an overall power calibration or to calibrate the ADC

output. While the ADC outputs a 20-bit twos complement

value, the maximum full-scale positive value from the ADC is

limited to 40,000h (+262,144 decimal). The maximum full-

scale negative value is limited to C0000h (–262,144 decimal). If

the analog inputs are overranged, the ADC output code will

clamp at these values. With the specified full-scale analog input

signal of 0.5 V (or 0.25 V or 0.125 V—see Analog Inputs sec-

tion), the ADC will produce an output code that is approximately

63% of its full-scale value. This is illustrated in Figure 23. The

diagram in Figure 23 shows a full-scale voltage signal being

applied to the differential inputs V1P and V1N. The ADC

output swings between D7AE1h (–165,151) and 2851Fh

(+165,151). This is approximately 63% of the full-scale value

40,000h (262,144). Overranging the analog inputs with more

than 0.5 V differential (0.25 V or 0.125 V, depending on

Channel 1 full-scale selection) will cause the ADC output to

increase towards its full-scale value. However, for specified

operation, the differential signal on the analog inputs should

not exceed the recommended value of 0.5 V.

V_IN

V_REF

Code(ADC) = 3.0492×

× 262,144

Therefore, with a full-scale signal on the input of 0.5 V and an

internal reference of 2.42 V, the ADC output code is nominally

165,151 or 2851Fh. The maximum code from the ADC is

262,144, which is equivalent to an input signal level of 0.794 V.

However, for specified performance it is not recommended that the

full-scale input signal level of 0.5 V be exceeded.

Reference Circuit

Shown in Figure 22 is a simplified version of the reference out-

put circuitry. The nominal reference voltage at the REF_IN/OUT

pin is 2.42 V. This is the reference voltage used for the ADCs in

the ADE7759. However, Channel 1 has three input range selec-

tions, which are selected by dividing down the reference value

used for the ADC in Channel 1. The reference value used for

Channel 1 is divided down to 1/2 and 1/4 of the nominal value

by using an internal resistor divider, as shown in Figure 22.

REV. A

–17–

ADE7759

2.42V, 1.21V, 0.6V

{GAIN[4:3]}

ꢅ1, ꢅ2, ꢅ4,

ꢅ8, ꢅ16

REFERENCE

{GAIN[2:0]}

DIGITAL

TO WAVEFORM

V1P

V1N

DIGITAL LPF

HPF

INTEGRATOR*

MULTIPLIER

SAMPLE REGISTER

3

PGA1

ADC 1

V1

Sinc

TO MULTIPLIER

∫

CHANNEL 1 (ACTIVE POWER)

DATA RANGE AFTER

INTEGRATOR (50Hz)

50Hz

801HEX–7FFHEX

APGAIN[11:0]

2E72Eh

+94.5% FS

+63% FS

1EF74h

F7BAh

00000h

F0846h

V1

0.5V, 0.25V,

+31.5% FS

0.125V, 62.5mV,

31.3mV, 15.6mV,

+FS

40000h

2851Fh

CHANNEL 1 (ACTIVE POWER)

DATA RANGE

–31.5% FS

–63% FS

+63% FS

0V

3C7AEh

2851Fh

+94.5% FS

E108Ch

D18D2h

+63% FS

–94.5% FS

00000h

000h

7FFh

801h

1428Fh

00000h

EBD71h

+31.5% FS

ANALOG

INPUT

60Hz

APGAIN[11:0]

–63% FS

–FS

D7AE1h

C0000h

RANGE

–31.5% FS

–63% FS

CHANNEL 1 (ACTIVE POWER)

DATA RANGE AFTER

INTEGRATOR (60Hz)

D7AE1h

C3852h

ADC OUTPUT

WORD RANGE

–94.5% FS

000h

APGAIN[11:0]

7FFh

801h

+94.5% FS

26B50h

+63% FS

+31.5% FS

19CE0h

0CE70h

00000h

F3190h

E6320h

D94B0h

– 31.5% FS

– 63% FS

*WHEN DIGITAL INTEGRATOR IS ENABLED, FULL-SCALE OUTPUT DATA VARIES DEPENDING

ON THE SIGNAL FREQUENCY BECAUSE OF –20dB/DECADE FREQUENCY RESPONSE.

– 94.5% FS

000h

7FFh

801h

APGAIN[11:0]

Figure 23. ADC and Signal Processing in Channel 1

Channel 1 ADC Gain Adjust

wave form samples are transferred from the ADE7759 one byte

(eight bits) at a time, with the most significant byte shifted out

first. The 20-bit dataword is right justified and sign extended to

24 bits (three bytes)—see Serial Interface section.

The ADC gain in Channel 1 can be adjusted by using the multi-

plier and active power gain register (APGAIN[11:0]). The gain of

the ADC is adjusted by writing a twos complement 12-bit word

to the active power gain register. Below is the expression that

shows how the gain adjustment is related to the contents of the

active power gain register.

SAMPLING RATE (27.9kSPS, 14kSPS, 7kSPS, OR 3.5kSPS)

IRQ

16ꢄs

SCLK





APGAIN 



Code = ADC × 1+











2¹²

READ FROMWAVEFORM

0 0 0 01 HEX







DIN

For example, when 7FFh is written to the active power gain

register, the ADC output is scaled up by 50%. 7FFh = 2047

decimal, 2047/2¹²= 0.5. Similarly, 801h = 2047 decimal

(signed twos complement) and ADC output is scaled by –50%.

These two examples are illustrated in Figure 23.

DOUT

SIGN

CHANNEL 1 DATA

– 20 BITS

Figure 24. Waveform Sampling Channel 1

CHANNEL 1 AND CHANNEL 2 WAVEFORM SAMPLING

MODE

Channel 1 Sampling

The waveform samples may also be routed to the waveform

register (MODE[14:13] = 1, 0) to be read by the system master

(MCU). In waveform sampling mode, the WSMP bit (Bit 3) in

the interrupt enable register must also be set to Logic 1. The

active power and energy calculation will remain uninterrupted

during waveform sampling.

In Channel 1 and Channel 2 waveform sampling mode

(MODE[14:13] = 01), the output is a 40-bit waveform sample

data that contains the waveform samples from both Channel 1

and Channel 2 ADCs. Figure 25 shows the format of the 40-bit

waveform output.

When in waveform sample mode, one of four output sample

rates may be chosen by using Bits 11 and 12 of the mode regis-

ter DTRT(1, 0). The output sample rate may be 27.9 kSPS,

14 kSPS, 7 kSPS, or 3.5 kSPS—see Mode Register section. The

interrupt request output IRQ signals a new sample availability

by going active low. The timing is shown in Figure 24. The 20-bit

1 BYTE

2 BYTES

BIT 39

BIT 0

CH2[19:16] CH1[19:16]

CH1[15:0]

CH2[15:0]

Figure 25. 40-Bit Combined Channel 1 and Channel 2

Waveform Sample Data Format

–18–

REV. A

ADE7759

2.42V

CHANNEL 2 ADC

Channel 2 Sampling

ꢅ1, ꢅ2, ꢅ4,

ꢅ8, ꢅ16

REFERENCE

V2P

V2N

{GAIN [7:5]}

In Channel 2 waveform sampling mode (MODE[14:13] = 1, 1

and WSMP = 1), the ADC output code scaling for Channel 2 is

the same as Channel 1, i.e., the output swings between D7AE1h

(–165,151) and 2851Fh (+165,151)—see ADC Channel 1

section. However, before being passed to the waveform register,

the ADC output is passed through a single-pole, low-pass filter

with a cutoff frequency of 156 Hz. The plots in Figure 26 show

the magnitude and phase response of this filter.

–63%TO +63% FS

LPF1

1

TO

PGA2

ADC 2

V2

MULTIPLIER

TO

20

WAVEFORM

REGISTER

V1

0.5V, 0.25V, 0.125V,

62.5mV, 31.25mV

LPF OUTPUT

WORD RANGE

0V

40000h

2851Fh

257F6h

+FS

+63% FS

+59% FS

0

–20

–40

–60

–80

0

ANALOG

00000h

INPUT RANGE

DA80Ah

D7AE1h

C0000h

–59% FS

–63% FS

–FS

60Hz, –0.6dB

Figure 27. ADC and Signal Processing in Channel 2

60Hz, –21.04ꢀ

–10

PHASE COMPENSATION

When the HPF is disabled, the phase error between Channel 1 and

Channel 2 is zero from dc to 3.5 kHz. When HPF1 is enabled,

Channel 1 has a phase response illustrated in Figures 29 and 30.

Also shown in Figure 31 is the magnitude response of the filter.

As can be seen from the plots, the phase response is almost zero

from 45 Hz to 1 kHz. This is all that is required in typical energy

measurement applications.

–20

1

2

3

10

FREQUENCY – Hz

However, despite being internally phase compensated, the

ADE7759 must work with transducers that may have inherent

phase errors. For example, a phase error of 0.1° to 0.3° is not

uncommon for a CT (Current Transformer). These phase

errors can vary from part to part, and they must be corrected in

order to perform accurate power calculations. The errors associ-

ated with phase mismatch are particularly noticeable at low

power factors. The ADE7759 provides a means of digitally

calibrating these small phase errors. The ADE7759 allows a

small time delay or time advance to be introduced into the signal

processing chain in order to compensate for small phase errors.

Because the compensation is in time, this technique should only be

used for small phase errors in the range of 0.1° to 0.5°. Correcting

large phase errors using a time shift technique can introduce signifi-

cant phase errors at higher harmonics.

Figure 26. Magnitude and Phase Response of LPF1

The LPF1 has the effect of attenuating the signal. For example,

if the line frequency is 60 Hz, the signal at the output of LPF1

will be attenuated by 7%.

1

H( f ) =

= 0.93 = –0.6 dB



²

60 Hz

156 Hz

1+









Note that LPF1 does not affect the power calculation. The

signal processing chain in Channel 2 is illustrated in Figure 27.

Unlike Channel 1, Channel 2 has only one analog input range

(0.5 V differential). However, like Channel 1, Channel 2 does

have a PGA with gain selections of 1, 2, 4, 8, and 16. For energy

measurement, the output of the ADC is passed directly to the

multiplier and is not filtered. An HPF is not required to remove

any dc offset since it is only required to remove the offset from

one channel to eliminate errors due to offsets in the power cal-

culation. When in waveform sample mode, one of four output

sample rates can be chosen by using Bits 11 and 12 of the

mode register. The available output sample rates are 27.9 kSPS,

14 kSPS, 7 kSPS, or 3.5 kSPS—see Mode Register section. The

interrupt request output IRQ signals a new sample availability

by going active low. The timing is the same as that for

The phase calibration register (PHCAL[7:0]) is a twos comple-

ment signed single-byte register that has values ranging from 9Eh

(–98 in decimal) to 5Ch (92 in decimal). By changing the PHCAL

register, the time delay in the Channel 2 signal path can change

from –110 µs to +103 µs (CLKIN = 3.579545 MHz). One LSB is

equivalent to 1.12 µs time delay or advance. With a line frequency

of 60 Hz, this gives a phase resolution of 0.024° at the fundamental

(i.e., 360° × 1.12 µs × 60 Hz). Figure 28 illustrates how the phase

compensation is used to remove a 0.1° phase lead in Channel 1

due to the external transducer. To cancel the lead (0.1°) in

Channel 1, a phase lead must also be introduced into Channel 2.

The resolution of the phase adjustment allows the introduction of a

phase lead in increments of 0.024°. The phase lead is achieved by

introducing a time advance into Channel 2. A time advance of

4.48 µs is made by writing –4 (FCh) to the time delay block, thus

reducing the amount of time delay by 4.48 µs, or equivalently, a

phase lead of approximately 0.1° at line frequency of 60 Hz.

Channel 1 and is shown in Figure 24.

REV. A

–19–

ADE7759

V1P

0.4

0.3

HPF

20

PGA1

V1

ADC 1

V1N

V2P

LPF2

20

0.2

0.1

CHANNEL 2 DELAY

REDUCED BY 4.48ꢄs

(0.1ꢀ LEAD AT 60Hz)

FCH IN PHCAL [7:0]

1

DELAY BLOCK

PGA2

V2

ADC 2

1.12ꢄs/LSB

0.0

V2N

7

0

–0.1

–0.2

–0.3

–0.4

V2

V1

1

1 1 1 1 1 0 0

V2

PHCAL [7:0]

–110ꢄsTO +103ꢄs

0.1ꢀ

V1

60Hz

54

56

58

60

62

64

66

60Hz

FREQUENCY – Hz

Figure 31. Combined Gain Response of the HPF and Phase

Compensation (Deviation of Gain in % from Gain at 60 Hz)

Figure 28. Phase Calibration

0.30

0.25

0.20

0.15

0.10

0.05

0.00

–0.05

–0.10

ACTIVE POWER CALCULATION

Electrical power is defined as the rate of energy flow from source to

load. It is given by the product of the voltage and current wave-

forms. The resulting waveform is called the instantaneous power

signal, and it is equal to the rate of energy flow at every instant

of time. The unit of power is the watt or joules/second. Equa-

tion 3 gives an expression for the instantaneous power signal in

an ac system.

(1)

(2)

v(t) = 2 V(ωt)

i(t) = 2 I sin(ωt)

100 200 300 400 500 600 700 800 900 1000

FREQUENCY – Hz

where:

V = rms voltage

I = rms current

Figure 29. Combined Phase Response of the HPF and

Phase Compensation (100 Hz to 1 kHz)

p(t) = v(t) × i(t)

(3)

p(t) =VI –VI cos(2ωt)

The average power over an integral number of line cycles (n) is

given by the expression in Equation 4.

0.30

0.25

0.20

0.15

0.10

0.05

0.00

–0.05

–0.10

1

nT

P =

^nTp (t)dt =VI

∫

(4)

0

where T is the line cycle period. P is referred to as the active or

real power. Note that the active power is equal to the dc compo-

nent of the instantaneous power signal p(t) in Equation 3, i.e.,

VI. This is the relationship used to calculate active power in the

ADE7759. The instantaneous power signal p(t) is generated by

multiplying the current and voltage signals. The dc component

of the instantaneous power signal is then extracted by LPF2 (low-

pass filter) to obtain the active power information. This process

is illustrated in Figure 32. Since LPF2 does not have an ideal

“brick wall” frequency response (see Figure 33), the active power

signal will have some ripple due to the instantaneous power

signal. This ripple is sinusoidal and has a frequency equal to twice

the line frequency. Since the ripple is sinusoidal in nature, it will

be removed when the active power signal is integrated to calcu-

late energy—see Energy Calculation section.

40

45

50

55

60

65

70

FREQUENCY – Hz

Figure 30. Combined Phase Response of the HPF and

Phase Compensation (40 Hz to 70 Hz)

–20–

REV. A

ADE7759

INSTANTANEOUS

POWER SIGNAL

p(t) =V ꢅ I –V ꢅ I ꢅ cos(2ꢆt)

1999Ah

ACTIVE REAL POWER

SIGNAL =V ꢅ I

13333h

CCCDh

6666h

+30% FS

POSITIVE

POWER

+20% FS

+10% FS

VI

CCCDh

00000h

F999Ah

F3333h

ECCCDh

–10% FS

–20% FS

–30% FS

NEGATIVE

POWER

00000h

000h

7FFh

800h

{APGAIN [11:0]}

CURRENT

i(t) = 2 ꢅ I ꢅ sin(ꢆt)

CHANNEL 1 (ACTIVE POWER)

CALIBRATION RANGE

VOLTAGE

v(t) = 2 ꢅ V ꢅ sin(ꢆt)

Figure 35. Active Power Calculation Output Range

Figure 32. Active Power Calculation

ENERGY CALCULATION

0

As stated earlier, power is defined as the rate of energy flow.

This relationship can be expressed mathematically as:

–4

–8

dE

P =

(5)

(6)

dt

where P = power and E = energy.

Conversely, energy is given as the integral of power:

–12

–16

–20

E = ∫ Pdt

The AD7759 achieves the integration of the active power signal

by continuously accumulating the active power signal in the

40-bit active energy register (ASENERGY[39:0]). This discrete

time accumulation or summation is equivalent to integration in

continuous time. Equation 7 expresses this relationship:

–24

1

3

10

30

100

FREQUENCY – Hz

∞









E = ∫ P(t)dt = Lim

p(nT) × T

∑

Figure 33. Frequency Response of LPF2

_T→0



(7)

n = 0

Figure 34 shows the signal processing chain for the active power

calculation in the ADE7759. As explained, the active power is

calculated by low pass filtering the instantaneous power signal.

where n is the discrete time sample number and T is the

sample period.

The discrete time sample period (T) for the accumulation regis-

ter in the ADE7759 is 1.1 µs (4/CLKIN). As well as calculating

the energy, this integration removes any sinusodial components

which may be in the active power signal.

ACTIVE POWER

HPF

SIGNAL – P

I

CCCDh

CURRENT SIGNAL – i(t)

MULTIPLIER

LPF2

20

Figure 36 shows a graphical representation of this discrete time

integration or accumulation. The active power signal in the wave-

form register is continuously added to the active energy register.

This addition is a signed addition; therefore negative energy will be

subtracted from the active energy contents.

INSTANTANEOUS POWER SIGNAL – p(t)

–40%TO +40% FS

1

V

VOLTAGE SIGNAL – v(t)

1999Ah

As shown in Figure 36, the active power signal is accumulated

in a 40-bit signed register (AENERGY[39:0]). The active

power signal can be read from the waveform register by setting

MODE[14:13] = 0, 0 and setting the WSMP bit (Bit 3) in

the interrupt enable register to 1. Like Channel 1 and Channel 2

waveform sampling modes, the waveform data is available at

sample rates of 27.9 kSPS, 14 kSPS, 7 kSPS, or 3.5 kSPS—see

Figure 24. Figure 37 shows this energy accumulation for full-scale

signals (sinusodial) on analog inputs. The three curves displayed

illustrate the minimum period of time it takes the energy register to

roll over when the active power gain register contents are 7FFh,

000h, and 800h. The active power gain register is used to carry out

power calibration in the ADE7759. As shown, the fastest

integration time will occur when the active power gain register is

set to maximum full scale, i.e., 7FFh.

00h

Figure 34. Active Power Signal Processing

Shown in Figure 35 is the maximum code (hexadecimal) output

range for the active power signal (LPF2) when the digital inte-

grator is disabled. Note that when the integrator is enabled, the

output range changes depending on the input signal frequency.

Furthermore, the output range can also be changed by the

active power gain register—see Channel 1 ADC section. The

minimum output range is given when the active power gain

register contents are equal to 800h, and the maximum range is

given by writing 7FFh to the active power gain register. This

can be used to calibrate the active power (or energy) calculation

in the ADE7759.

REV. A

–21–

ADE7759

APOS [15:0]

15

SIGN

0

6

5

4

3

2

1

0

–1

–2

–3

–4

–5

–6

–7

–8

2

CURRENT CHANNEL

LPF2

WAVEFORM [24:0]

AENERGY [39:0]

+

23

39

0

20

+

VOLTAGE CHANNEL

ACTIVE POWER

SIGNAL = P

4

T

CLKIN

WAVEFORM

REGISTER

VALUES

WAVEFORM REGISTERVALUES ARE

ACCUMULATED (INTEGRATED) IN

THE ACTIVE ENERGY REGISTER

TIME – nT

Figure 36. Energy Calculation

AENERGY [39:0]

7F,FFFF,FFFFh. Therefore, the integration time under these

conditions is calculated as follows:

7F,FFFF,FFFFh

3F,FFFF,FFFFh

00,0000,0000h

APGAIN = 7FFh

APGAIN = 000h

APGAIN = 800h

7F , FFFF , FFFFh

Time =

×1.1µs = 11.53 seconds

CCCDh

POWER OFFSET CALIBRATION

TIME – sec

The ADE7759 also incorporates an active power offset regis-

ter (APOS[15:0]). This is a signed twos complement 16-bit

register that can be used to remove offsets in the active power

calculation—see Figure 36. An offset may exist in the power

calculation due to crosstalk between channels on the PCB or in

the IC itself. The offset calibration will allow the contents of the

active power register to be maintained at zero when no power is

being consumed.

23s

5.8s

11.5s

40,0000,0000

80,0000,0000h

Figure 37. Energy Register Rollover Time for Full-Scale

Power (Minimum and Maximum Power Gain)

The 256 LSBs (APOS = 0100h) written to the active power

offset register are equivalent to 1 LSB in the waveform sample

register, assuming the average value output from LPF2 to

store in the waveform register is CCCDh (52,429 in decimal)

when inputs on Channels 1 and 2 are both at full scale and

the digital integrator is turned off. At –60 dB down on Chan-

nel 1 (1/1000 of the Channel 1 full-scale input), the average

word value output from LPF2 is 52.429 (52,429/1,000). One

LSB in the waveform register has a measurement error of

1/52.429 × 100% = 1.9% of the average value. The active

power offset register has a resolution equal to 1/256 LSB of

the waveform register, thus the power offset correction reso-

lution is 0.007%/LSB (1.9%/256) at –60 dB. When the digital

integrator is turned on, the resolution of the LSB varies slightly

with the line frequency.

Note that the energy register contents will roll over to full-scale

negative (80,0000,0000h) and continue increasing in value when

the power or energy flow is positive—see Figure 37. Conversely, if

the power is negative, the energy register would underflow to full-

scale positive (7F, FFFF, FFFFh) and continue decreasing in

value. By using the interrupt enable register, the ADE7759

can be configured to issue an interrupt (IRQ) when the active

energy register is half-full (positive or negative) or when an

over/underflow occurs.

Integration Time under Steady Load

As mentioned in the last section, the discrete time sample

period (T) for the accumulation register is 1.1 µs (4/CLKIN).

With full-scale sinusoidal signals on the analog inputs, digital

integrator turned off, and the active power gain register set to

000h, the average word value from LPF2 is CCCD—see

Figures 34 and 35. The maximum value that can be stored in

the active energy register before it overflows is 2³⁹or

ENERGY-TO-FREQUENCY CONVERSION

ADE7759 also provides energy-to-frequency conversion for

calibration purposes. After initial calibration at manufacturing,

the manufacturer or end customer will often verify the energy

meter calibration. One convenient way to verify the meter cali-

bration is for the manufacturer to provide an output frequency

that is proportional to the energy or active power under steady

–22–

REV. A

ADE7759

load conditions. This output frequency can provide a simple,

single-wire, optically isolated interface to external calibration

equipment. Figure 38 illustrates the energy-to-frequency con-

version in the ADE7759.

output. Therefore, the content of CFDEN should always be set

no less than that of the CFNUM register, i.e., the maximum

output frequency from CF pin will never exceed that of the ETF

output. The power-up default value for CFDEN is 3Fh and

CFNUM is 0h.

The energy-to-frequency conversion is accomplished by accu-

mulating the active power signal in a 24-bit register. An output

pulse is generated when there is a zero to one transition on the

MSB (most significant bit) of the register. Under steady load con-

ditions the output frequency is proportional to the active power.

The output frequency at CF, with full-scale ac signals on

Channel 1 and Channel 2 and CFDEN = 000h, CFNUM = 000h,

and APGAIN = 000h, is approximately 5.593 kHz. This can be

calculated as follows:

The output frequency will have a slight ripple at a frequency

equal to twice the line frequency. This is due to imperfect filter-

ing of the instantaneous power signal to generate the active

power signal—see Active Power Calculation section. Equation 3

gives an expression for the instantaneous power signal. This is

filtered by LPF2, which has a magnitude response given by

Equation 10:

1

H( f ) =

With the active power gain register set to 000h, the average

value of the instantaneous power signal (output of LPF2) is

CCCDh or 52,429 decimal. An output frequency is generated

on CF when the MSB in the energy-to-frequency register (24 bits)

toggles, i.e., when the register accumulates 2²³. This means the

register is updated 2²³/CCCDh times (or 159.999 times). Since

the update rate is 4/CLKIN or 1.1175 µs, the time between

MSB toggles (CF pulses) is given as:

(10)

1+ f /8.9 Hz

The active power signal (output of LPF2) can be rewritten as:







VI







p(t) =VI −

cos 4πf t

(

)

l

(11)

1+ 2f_l/8.9 Hz

where f_lis the line frequency (e.g., 60 Hz).

159.999 ·1.1175 ms =1.78799·10^–4s(5592.86 Hz)

From Equation 6:

Equation 8 gives an expression for the output frequency at the

Energy-to-Frequency (ETF) output with the contents of CFDEN

and CFNUM registers are both zero.









VI

E(t) =VIt −

sin 4πf t

(

)





l

(12)

4πf 1+ 2f /8.9 Hz

(

)









l

Average LPF2 Output × CLKIN

ETF Output (Hz) =

(8)

From Equation 12 it can be seen that there is a small ripple in

the energy calculation due to a sin(2ωt) component. This is

shown in Figure 39. The active energy calculation is shown by

the dashed straight line and is equal to V × I × t. The sinusoidal

ripple in the active energy calculation is also shown. Since the

average value of a sinusoid is zero, this ripple will not contribute

to the energy calculation over time. However, the ripple can be

observed in the frequency output, especially at higher output

frequencies. The ripple will get larger as a percentage of the

frequency at larger loads and higher output frequencies. The rea-

son is that at higher output frequencies the integration or averaging

time in the energy-to-frequency conversion process is shorter. As

a consequence, some of the sinusoidal ripple is observable in the

frequency output. Choosing a lower output frequency at CF for

calibration can significantly reduce the ripple. Also, averaging the

output frequency by using a longer gate time for the counter will

achieve the same results.

2²⁵

This output frequency is easily scaled by a pair of calibration

frequency divider registers (CFDEN[11:0] and CFNUM[11:0]).

These frequency scaling registers are 12-bit registers that can

scale the output frequency by 1 to 2¹². The output frequency is

given by the expression below:

CFNUM [11:0]+1

CFDEN [11:0]+1

CF(Hz) = ETF Output (Hz)×

(9)

For example, if the CF output frequency is 5.59286 kHz while

the contents of CFNUM and CFDEN are zero, the CF output

frequency can be set to 25 Hz by writing 8 BDh (2237 in deci-

mal) to the CFDEN register and 00Ah (10 in decimal) to the

CFNUM register. Note that the CFNUM and CFDEN regis-

ters are meant only to scale down the frequency from the ETF

APOS [15:0]

15

0

6

5

4

3

2

1

0

–1

–2

–3

–4

–5

–6

–7

–8

2

SIGN

2

LPF2

WAVEFORM [23:0]

+

23

0

ACTIVE POWER OFFSET

CALIBRATION

20

+

ENERGY-TO-FREQUENCY

+

23

0

ACTIVE POWER

SIGNAL – P

+

MSB

TRANSITION

CFNUM [11:0]

CFDEN [11:0]

11

0

CF

Figure 38. Energy-to-Frequency Conversion

–23–

REV. A

ADE7759

E(t)

From Equations 5 and 11:

Vlt

E(t) = ^nTVIdt –

^nTcos (2 wt)dt







VI



(13)

∫





4 ꢀf 1+ 2f / 8.9 Hz



0

(

)

0

l





where n is an integer and T is the line cycle period.

Since the sinusoidal component is integrated over an integer

number of line cycles, its value is always zero. Therefore:

VI

4␲ƒ (1 + 2ƒ /8.9Hz)

–

sin(4␲ƒ t)

l

E(t) = ^nTVIdt + 0

∫

(14)

(15)

0

Figure 39. Output Frequency Ripple

E(t) =VInT

LINE CYCLE ENERGY ACCUMULATION MODE

Note that in this mode, the 14-bit LINECYC register can hold a

maximum value of 16,383. In other words, the line cycle

energy accumulation mode can be used to accumulate active

energy for a maximum duration over 16,383 half-line cycles. At

60 Hz line frequency, it translates to a total duration of 16,383/

120 Hz = 136.5 seconds. The 40-bit signed LENERGY register

can overflow if large signals are present at the inputs. The

LENERGY register can only hold up to 11.53 seconds of active

energy when both its input channels are at ac full-scale—see

Integration Time Under Steady Load section. Large LINECYC

content is meant to be used only when the input signal is low

and extensive averaging is required to reduce the noise.

In line cycle energy accumulation mode, the energy accumula-

tion of the ADE7759 can be synchronized to the Channel 2 zero

crossing so that active energy can be accumulated over an inte-

gral number of half line cycles. The advantage of summing the

active energy over an integer number of half-line cycles is that

the sinusoidal component in the active energy is reduced to zero.

This eliminates any ripple in the energy calculation. Energy is

calculated more accurately and in a shorter time because the

integration period can be shortened. By using the line cycle

energy accumulation mode, the energy calibration can be greatly

simplified and the time required to calibrate the meter can be sig-

nificantly reduced. The ADE7759 is placed in line cycle energy

accumulation mode by setting Bit 7 (CYCMODE) in the mode

register. In line cycle energy accumulation mode the ADE7759

accumulates the active power signal in the LENERGY register

(Address 14h) for an integral number of half cycles, as shown in

Figure 40. The number of half-line cycles is specified in the

LINECYC register (Address 14h). The ADE7759 can accumu-

late active power for up to 16,383 half cycles. Because the active

power is integrated on an integral number of half-line cycles, at

the end of a line cycle energy accumulation cycle, the CYCEND

flag in the interrupt status register is set (Bit 2). If the CYCEND

enable bit in the interrupt enable register is enabled, the IRQ

output will also go active low. Thus the IRQ line can also be

used to signal the completion of the line cycle energy accumula-

tion. Another calibration cycle will start as long as the CYCMODE

bit in the mode register is set. Note that the result of the first

calibration is invalid and should be ignored. The result of all

subsequent line cycle accumulation is correct.

CALIBRATING THE ENERGY METER

Calculating the Average Active Power

When calibrating the ADE7759, the first step is to calibrate the

frequency on CF to some required meter constant, e.g.,

3200 imp/kWh.

To determine the output frequency on CF, the average value of

the active power signal (output of LPF2) must first be deter-

mined. One convenient way to do this is to use the line cycle

energy accumulation mode. When the CYCMODE (Bit 7) bit

in the mode register is set to a Logic 1, energy is accumulated

over an integer number of half-line cycles as described in the

last section. Since the line frequency is fixed at, say, 60 Hz, and

the number of half cycles of integration is specified, the total

integration time is given as:

1

× number of half cycles

2 × 60 Hz

APOS [15:0]

15

0

6

5

4

3

2

1

0

–1

–2

–3

–4

–5

–6

–7

–8

2

SIGN

2

LPF2

WAVEFORM [23:0]

+

23

39

0

+

FROM

MULTIPLIER

ACTIVE POWER

SIGNAL – P

LENERGY [39:0]

+

CCCDh

00h

LPF1

ZERO CROSS

DETECT

CALIBRATION

CONTROL

CHANNEL 2

ADC

LINECYC [13:0]

Figure 40. Energy Calculation in Line Cycle Energy Accumulation Mode

–24–

REV. A

ADE7759

For 255 half cycles this would give a total integration time of 2.125

seconds. This would mean that the energy register was

updated 2.125/1.1175 µs (4/CLKIN) times. The average output

value of LPF2 is given as:

frequency is accurately known during calibration. Using line

cycle energy accumulation mode, the calibration time can be

reduced by synchronizing energy accumulation to the zero

crossing of the voltage channel—see the Line Cycle Energy

Accumulation Mode section. However, this requires the line

frequency to be precisely known. As shown in Equation 16, the

average value of LPF2 is directly proportional to the line fre-

quency. Any deviation from the nominal frequency will directly

affect the calibration result. The line frequency could be mea-

sured using the ZX output of the ADE7759. Alternatively, the

average value of LPF2 can be calculated from the output frequency

from CF—see the Energy to Frequency Conversion section.

Contents of LENERGY[39:0]at the end

Number of times LENERGY[39:0]was updated

Or, equivalently, in terms of contents of various ADE7759

registers and CLKIN and line frequencies (f_l):

LENERGY[39:0]× 8 × f_l

LINECYC[13:0]× CLKIN

AverageWord (LPF2) =

(16)

Note that besides CFNUM and CFDEN registers, changing

APGAIN[11:0] register will also affect the output frequency

from CF. The APGAIN register has a resolution of 0.0244%/LSB.

where f_lis the line frequency.

Energy Meter Display

Calibrating the Frequency at CF

Besides the pulse output, which is used to verify calibration, a

solid state energy meter will very often require some form of

display. The display should show the amount of energy con-

sumed in kWh (kilowatthours). One convenient and simple way

to interface the ADE7759 to a display or energy register (e.g.,

MCU with nonvolatile memory) is to use CF. For example, the

CF frequency could be calibrated to 1,000 imp/kWhr. The

MCU would count pulses from CF. Every pulse would be

equivalent to 1 watt-hour. If more resolution is required, the CF

frequency could be set to, say, 10,000 imp/kWh.

Once the average active power signal is calculated, it can be

used to determine the frequency at CF before calibration. When

the frequency before calibration is known, the pair of CF fre-

quency divider registers (CFNUM and CFDEN) can be adjusted

so as to produce the required frequency on CF. In this example,

a meter constant of 3200 imp/kWh is chosen as an appropriate

constant. This means that under a steady load of 1 kW, the

output frequency on CF would be:

3200 imp/kWh

60 min · 60 sec 3600

3200

Frequency (CF) =

=

= 0.8888 Hz

If more flexibility is required when monitoring energy usage, the

active energy register (AENERGY) can be used to calculate

energy. A full description of this register can be found in the

Energy Calculation section. The AENERGY register gives the

user both sign and magnitude information regarding energy

consumption. On completion of the CF frequency output cali-

bration, i.e., after the active power gain (APGAIN) register has

been adjusted, a second calibration sequence can be initiated.

The purpose of this second calibration routine is to determine a

kWh/LSB coefficient for the AENERGY register. Once the

coefficient has been calculated, the MCU can determine the

energy consumption at any time by reading the AENERGY

contents and multiplying by the coefficient to calculate kWh.

Assuming the meter is set up with a test current (basic current)

of 20 A and a line voltage of 220 V for calibration, the load is

calculated as 220 V × 20 A = 4.4 kW. Therefore, the expected

output frequency on CF under this steady load condition would

be 4.4 × 0.8888 Hz = 3.9111 Hz. Under these load conditions,

the transducers on Channel 1 and Channel 2 should be selected

such that the signal on the voltage channel should see approxi-

mately half scale and the signal on the current channel about 1/8

of full scale (assuming a maximum current of 80 A). The aver-

age value from LPF2 is calculated as 3,276.81 decimal using the

calibration mode as described above. Then using Equation 8

(energy-to-frequency conversion), the frequency under this

load is calculated as:

CLKIN FREQUENCY

In this data sheet, the characteristics of the ADE7759 are

shown with the CLKIN frequency equal to 3.579545 MHz.

However, the ADE7759 is designed to have the same accu-

racy at any CLKIN frequency within the specified range. If

the CLKIN frequency is not 3.579545 MHz, various timing

and filter characteristics will need to be redefined with the

new CLKIN frequency. For example, the cutoff frequencies

of all digital filters (LPF1, LPF2, HPF1, etc.) will shift in

proportion to the change in CLKIN frequency according to

the following equation:

3276.81× 3.579545 MHz

Frequency (CF ) =

= 349.566 Hz

2²⁵

This is the frequency with the contents of the CFNUM and

CFDEN registers equal to 000h. The desired frequency out is

3.9111 Hz. Therefore, the CF frequency must be divided by

349.566/3.9111 Hz or 89.3779 decimal. This is achieved by

loading the pair of CF divider registers with the closest rational

number. In this case, the closest rational number is found to be

25/2234 (or 19h/8BAh). Therefore, 18h and 8B9h should be

written to the CFNUM and CFDEN registers, respectively.

Note that the CF frequency is divided by the contents of

(CFNUM + 1)/(CFDEN + 1). With the CF divide registers

contents equal to 18h/8B9h, the output frequency is given as

349.566 Hz/89.36 = 3.91188 Hz. Note that this setting has an

error of +0.02%.

CLKIN Frequency

3.579545 MHz

New Frequency = Original Frequency ×

(17)

The change of CLKIN frequency does not affect the timing

characteristics of the serial interface because the data transfer is

synchronized with serial clock signal (SCLK). But one needs to

observe the read/write timing of the serial data transfer—see

Timing Characteristics. Table III lists various timing changes

that are affected by CLKIN frequency.

Calibrating CF is made easy by using the line cycle energy

accumulation mode on the ADE7759, provided that the line

REV. A

–25–

ADE7759

Table III. Frequency Dependencies of the ADE7759 Parameters

The communications register is an 8-bit wide register. The

MSB determines whether the next data transfer operation is a

read or a write. The five LSBs contain the address of the register

to be accessed. See Communications Register section for a more

detailed description. Figures 42 and 43 show the data transfer

sequences for a read and write operation, respectively.

Parameter

Nyquist frequency for CH 1 and 2 ADCs CLKIN/8

PHCAL resolution (seconds per LSB) 4/CLKIN

CLKIN Dependency

Active Energy register update rate (Hz) CLKIN/4

Waveform sampling rate (Number of

samples per second)

On completion of a data transfer (read or write), the ADE7759

once again enters communications mode.

WAVSEL 1, 0 = 0

0

1

0

1

CLKIN/128

CLKIN/256

CLKIN/512

CLKIN/1024

524,288/CLKIN

0

1

CS

SCLK

COMMUNICATIONS REGISTERWRITE

Maximum ZXTOUT period

DIN

0

0 0 ADDRESS

SUSPENDING THE ADE7759 FUNCTIONALITY

The analog and the digital circuit can be suspended separately.

The analog portion of the ADE7759 can be suspended by set-

ting the ASUSPEND bit (Bit 4) of the mode register to logic

high—see Mode Register section. In suspend mode, all waveform

samples from the ADCs will be set to zeros. The digital circuitry

can be halted by stopping the CLKIN input and maintaining

a logic high or low on CLKIN pin. The ADE7759 can be reacti-

vated by restoring the CLKIN input and setting the ASUSPEND

bit to logic low.

DOUT

MULTIBYTE READ DATA

Figure 42. Reading Data from the ADE7759 via the

Serial Interface

CS

SCLK

COMMUNICATIONS REGISTERWRITE

ADDRESS

DIN

1

0

MULTIBYTE WRITE DATA

APPLICATION INFORMATION

Figure 43. Writing Data to the ADE7759 via the Serial

Interface

Application Note AN-564 contains detailed information on how

to design an ANSI Class 100 watt-hour meter based on the

ADE7756, a pin-to-pin compatible product with the ADE7759.

Application Note AN-578 describes an algorithm on how to

calculate the voltage and current rms values using an external

MCU. It is available from the ADE7756 product homepage

under the Application Note link on the energy metering home-

page, www.analog.com/energymeter.

A data transfer is complete when the LSB of the ADE7759

register being addressed (for a write or a read) is transferred to

or from the ADE7759.

The serial interface of the ADE7759 is made up of four signals:

SCLK, DIN, DOUT, and CS. The serial clock for a data trans-

fer is applied at the SCLK logic input. This logic input has a

Schmitt-trigger input structure, which allows slow rising (and

falling) clock edges to be used. All data transfer operations are

synchronized to the serial clock. Data is shifted into the ADE7759

at the DIN logic input on the falling edge of SCLK. Data is

shifted out of the ADE7759 at the DOUT logic output on a

rising edge of SCLK. The CS logic input is the chip select

input. This input is used when multiple devices share the serial

bus. A falling edge on CS also resets the serial interface and

places the ADE7759 into communications mode. The CS

input should be driven low for the entire data transfer opera-

tion. Bringing CS high during a data transfer operation will

abort the transfer and place the serial bus in a high impedance

state. The CS logic input may be tied low if the ADE7759 is the

only device on the serial bus. However, with CS tied low, all

initiated data transfer operations must be fully completed, i.e.,

the LSB of each register must be transferred as there is no other

way of bringing the ADE7759 back into communications mode

without resetting the entire device, i.e., using RESET.

SERIAL INTERFACE

All ADE7759 functionality is accessible via several on-chip regis-

ters—see Figure 41. The contents of these registers can be updated

or read using the on-chip serial interface. After power-on, or tog-

gling the RESET pin low, or a falling edge on CS, the ADE7759 is

placed in communications mode. In communications mode the

ADE7759 expects a write to its communications register. The

data written to the communications register determines whether

the next data transfer operation will be a read or a write and also

which register is accessed. Therefore, all data transfer operations

with the ADE7759, whether a read or a write, must begin with a

write to the communications register.

COMMUNICATIONS

REGISTER

DIN

IN

OUT

REGISTER #1

DOUT

IN

OUT

REGISTER #2

REGISTER #3

REGISTER

ADDRESS

DECODE

IN

OUT

Serial Write Operation

The serial write sequence takes place as follows. With the

ADE7759 in communications mode (i.e., the CS input logic

low), a write to the communications register first takes place.

The MSB of this byte transfer is a 1, indicating that the data

transfer operation is a write. The first five LSBs of this byte

contain the address of the register to be written to. The ADE7759

starts shifting in the register data on the next falling edge of

SCLK. All remaining bits of register data are shifted in on the

falling edge of subsequent SCLK pulses—see Figure 44.

IN

OUT

REGISTER #n –1

REGISTER #n

IN

OUT

Figure 41. Addressing ADE7759 Registers via the

Communications Register

–26–

REV. A

ADE7759

As explained earlier, the data write is initiated by a write to

the communications register followed by the data. During a

data write operation to the ADE7759, data is transferred to

all on-chip registers one byte at a time. After a byte is trans-

ferred into the serial port, there is a finite time before it is

transferred to one of the ADE7759 on-chip registers. Although

another byte transfer to the serial port can start while the

previous byte is being transferred to an on-chip register, this

second byte transfer should not finish until at least 4 µs after

the end of the previous byte transfer. This functionality is

expressed in the timing specification t₆—see Figure 44. If a

write operation is aborted during a byte transfer (CS brought

high), then that byte will not be written to the destination

register.

was the case with the data write operation, a data read must be

preceded by a write to the communications register.

With the ADE7759 in communications mode (i.e., CS logic

low), an 8-bit write to the communications register first takes

place. The MSB of this byte transfer is a 0, indicating that the

next data transfer operation is a read. The first five LSBs of this

byte contain the address of the register that is to be read. The

ADE7759 starts shifting out of the register data on the next

rising edge of SCLK—see Figure 46. At this point, the DOUT

logic output leaves its high impedance state and starts driving

the data bus. All remaining bits of register data are shifted out

on subsequent SCLK rising edges. The serial interface also

enters communications mode again as soon as the read has been

completed. At this point, the DOUT logic output enters a high

impedance state on the falling edge of the last SCLK pulse. The

read operation may be aborted by bringing the CS logic input

high before the data transfer is complete. The DOUT output

enters a high impedance state on the rising edge of CS.

Destination registers may be up to 3 bytes wide—see the Regis-

ter Description section. Therefore, the first byte shifted into

the serial port at DIN is transferred to the MSB (Most Signifi-

cant Byte) of the destination register. If the addressed register

is 12 bits wide, for example, a two-byte data transfer must

take place. The data is always assumed to be right justified:

therefore, in this case, the four MSBs of the first byte would be

ignored and the four LSBs of the first byte written to the

ADE7759 would be the four MSBs of the 12-bit word. Figure 45

illustrates this example.

When an ADE7759 register is addressed for a read operation,

the entire contents of that register are transferred to the serial

port. This allows the ADE7759 to modify its on-chip registers

without the risk of corrupting data during a multibyte transfer.

Note that when a read operation follows a write operation, the

read command (i.e., write to communications register) should

not happen for at least 4 µs after the end of the write operation.

If the read command is sent within 4 µs of the write operation,

the last byte of the write operation may be lost. This timing

constraint is given as timing specification t₉.

Serial Read Operation

During a data read operation from the ADE7759, data is shifted

out at the DOUT logic output on the rising edge of SCLK. As

t₈

CS

t₁

t₆

t₃

t₇

SCLK

t₄

t₂

t₅

A2

A4

A3

1

0

A0

DB7

DB0

A1

DB0

DB7

DIN

MOST SIGNIFICANT BYTE

LEAST SIGNIFICANT BYTE

COMMAND BYTE

Figure 44. Serial Interface Write Timing Diagram

SCLK

DIN

X

DB11 DB10 DB9

DB8

DB7

DB6

DB5

DB4

DB3

DB2

DB1

DB0

MOST SIGNIFICANT BYTE

LEAST SIGNIFICANT BYTE

Figure 45. 12-Bit Serial Write Operation

CS

t₁

t₁₃

t₉

t₁₀

SCLK

DIN

0

A2

A4

A3

A0

A1

t₁₂

t₁₁

DB0

DOUT

DB7

DB0

MOST SIGNIFICANT BYTE

LEAST SIGNIFICANT BYTE

COMMAND BYTE

Figure 46. Serial Interface Read Timing Diagram

–27–

REV. A

ADE7759

CHECKSUM REGISTER

Note that a read to the CHKSUM register will also generate a

checksum of the CHKSUM register itself.

The ADE7759 has a checksum register (CHKSUM[5:0]) to

ensure that the data bits received in the last serial read operation

are not corrupted. The 6-bit checksum register is reset before

the first bit (MSB of the register to be read) is put on the DOUT

pin. During a serial read operation, when each data bit becomes

available on the rising edge of SCLK, the bit will be added to

the checksum register. In the end of the serial read operation,

the content of the checksum register will be the sum of all the

ones contained in the register previously read. Using the checksum

register, the user can determine if an error has occurred during

the last read operation.

CONTENT OF REGISTER (n-bytes)

DOUT

+

CHECKSUM REGISTER ADDR: 1Eh

+

Figure 47. Checksum Register for Serial Interface Read

Table IV. Register List

Address Name

R/W No. of Bits Default

Description

01h

WAVEFORM

R

24/40

0h

The Waveform Register is a read-only register. This register con-

tains the sampled waveform data from Channel 1, Channel 2, or the

active power signal. The data source and the length of the waveform

registers are selected by data bits 14 and 13 in the mode register—

see Channel 1 and 2 Sampling section.

02h

AENERGY

R

40

0h

Active Energy Register. Active power is accumulated (Integrated)

over time in this 40-bit, read-only register. The energy register

can hold a minimum of 11.53 seconds of active energy information

with full-scale analog inputs before it overflows—see Energy Calcu-

lation section.

03h

04h

RSTENERGY

STATUS

R

40

8

0h

Same as the active energy register except that the register is reset to

0 following a read operation.

40h

Interrupt Status Register. This is an 8-bit read-only register. The

status register contains information regarding the source of

ADE7759 interrupts—see Interrupts section.

05h

06h

RSTSTATUS

MODE

R

8

0h

Same as the interrupt status register except that the register con-

tents are reset to 0 (all flags cleared) after a read operation.

R/W 16

000Ch

Mode Register. This is a 16-bit register through which most of

the ADE7759 functionality is accessed. Signal sample rates, filter

enabling, and calibration modes are selected by writing to this

register. The contents may be read at any time—see Mode Register

section.

07h

08h

CFDEN

CH1OS

R/W 12

3Fh

80h

CF Frequency Divider Denominator Register. The output fre-

quency on the CF pin is adjusted by writing to this 12-bit read/write

register—see Energy-to-Frequency Conversion section.

R/W

8

Channel 1 Offset Adjust. The MSB is used to enable the digital inte-

grator. Bit 6 is not used. Writing to Bits 0 to 5 allows offsets on

Channel 1 to be removed—see Analog Inputs section and CH1OS

Register section.

09h

0Ah

CH2OS

GAIN

R/W

6

8

0h

Channel 2 Offset Adjust. Writing to this 6-bit register allows any offsets

on Channel 2 to be removed—see Analog Inputs section.

PGA Gain Adjust. This 8-bit register is used to adjust the gain selec-

tion for the PGA in Channel 1 and 2—see Analog Inputs section.

–28–

REV. A

ADE7759

Address Name

R/W No. of Bits Default Description

R/W 12 0h

0Bh

APGAIN

Active Power Gain Adjust. This is a 12-bit register. The active power

calculation can be calibrated by writing to this register. The calibration

range is ±50% of the nominal full-scale active power. The resolution of the

gain adjust is 0.0244%/LSB—see Channel 1 ADC Gain Adjust section.

0Ch

PHCAL

R/W

8

0h

Phase Calibration Register. The phase relationship between Channel 1

and Channel 2 can be adjusted by writing to this 8-bit register. The

valid content of this twos complement register is between 9Eh and

5Ch, which is a phase difference of –2.365∞ to +2.221∞ at 60 Hz in

0.0241∞ steps—see Phase Compensation section.

0Dh

0Eh

APOS

R/W 16

R/W 12

0h

Active Power Offset Correction. This 16-bit register allows small off-

sets in the Active Power calculation to be removed—see Active Power

Calculation section.

ZXTOUT

FFFh

Zero Cross Timeout. If no zero crossings are detected on Channel 2

within a time period specified by this 12-bit register, the interrupt

request line (IRQ) will be activated. The maximum timeout period is

0.15 seconds—see Zero Crossing Detection section.

0Fh

10h

SAGCYC

IRQEN

R/W

8

FFh

40h

Sag Line Cycle Register. This 8-bit register specifies the number of

consecutive half-line cycles the signal on Channel 2 must be below

SAGLVL before the SAG output is activated—see Voltage Sag

Detection section.

Interrupt Enable Register. ADE7759 interrupts may be deactivated at

any time by setting the corresponding bit in this 8-bit enable register to

Logic 0. The status register will continue to register an interrupt event

even if disabled. However, the IRQ output will not be activated—see

Interrupts section.

11h

SAGLVL

R/W

8

0h

Sag Voltage Level. An 8-bit write to this register determines at what

peak signal level on Channel 2 the SAG pin will become active. The

signal must remain low for the number of cycles specified in the

SAGCYC register before the SAG pin is activated—see Line Voltage

Sag Detection section.

12h

13h

TEMP

R

8

4

0h

Temperature Register. This is an 8-bit register which contains the

result of the latest temperature conversion—see Temperature

Measurement section.

LINECYC

R/W

3FFFh

Line Cycle Energy Accumulation Mode Half-Cycle Register. This

14-bit register is used during line cycle energy accumulation mode to

set the number of half-line cycles active energy is accumulated—see

Line Cycle Energy Accumulation Mode section.

14h

15h

LENERGY

CFNUM

R

40

2

0h

Line Cycle Energy Accumulation Mode Active Energy Register. This

40-bit register accumulates active energy during line cycle energy

accumulation mode. The number of half-line cycles is set by the

LINECYC register—see Line Cycle Energy Accumulation Mode section.

R/W

CF Frequency Divider Numerator Register. The output frequency on

the CF pin is adjusted by writing to this 12-bit read/write register—see

Energy to Frequency Conversion section.

1Eh

1Fh

CHKSUM

DIEREV

R

6

8

0h

Checksum Register. This 6-bit read-only register is equal to the sum of

all the ones in the previous read—see Serial Read Operation section.

01h

Die Revision Register. This 8-bit read-only register contains the revision

number of the silicon.

REV. A

–29–

ADE7759

REGISTER DESCRIPTIONS

Communications Register

All ADE7759 functionality is accessed via the on-chip registers.

Each register is accessed by first writing to the communications

register and then transferring the register data. A full description

of the serial interface protocol is given in the Serial Interface

section.

The communications register is an 8-bit, write-only register

that controls the serial data transfer between the ADE7759 and

the host processor. All data transfer operations must begin with

a write to the communications register. The data written to the

communications register determines whether the next operation

is a read or a write and which register is being accessed. Table V

outlines the bit designations for the communications register.

Table V. Communications Register

DB7

DB6

0

DB5

0

DB4

A4

DB3

A3

DB2

A2

DB1

A1

DB0

A0

W/R

Bit

Location

Bit

Mnemonic

Description

0 to 4

A0 to A4

The five LSBs of the communications register specify the register for the data transfer opera-

tion. Table III lists the address of each ADE7759 on-chip register.

5 to 6

7

RESERVED

These bits are unused and should be set to zero.

W/R

When this bit is a Logic 1, the data transfer operation immediately following the write to the

Communications register will be interpreted as a write to the ADE7759. When this bit is a

Logic 0, the data transfer operation immediately following the write to the communications

register will be interpreted as a read operation.

–30–

REV. A

ADE7759

Mode Register (06H)

The ADE7759 functionality is configured by writing to the mode register—see Figure 45. Table VI summarizes the functionality of

each bit in the mode register.

Table VI. Mode Register

Bit

Location

Bit

Mnemonic

Description

0

1

2

3

4

DISHPF

DISLPF2

DISCF

The HFP (high-pass filter) in Channel 1 is disabled when this bit is set.

The LPF (low-pass filter) after the multiplier (LPF2) is disabled when this bit is set.

The frequency output CF is disabled when this bit is set.

DISSAG

ASUSPEND

The line voltage sag detection is disabled when this bit is set.

By setting this bit to Logic 1, both ADE7759s’ A/D converters can be turned off. In normal

operation, this bit should be left at Logic 0. All digital functionality can be stopped by suspending

the clock signal at CLKIN pin.

5

6

TEMPSEL

SWRST

The temperature conversion starts when this bit is set to 1. This bit is automatically reset to

0 when the temperature conversion is finished.

Software Chip Reset. A data transfer should not take place to the ADE7759 for at least 18 µs after

a software reset.

7

CYCMODE

DISCH1

DISCH2

SWAP

Setting this bit to Logic 1 places the chip in line cycle energy accumulation mode.

ADC 1 (Channel 1) inputs are internally shorted together.

8

9

ADC 2 (Channel 2) inputs are internally shorted together.

10

By setting this bit to Logic 1 the analog inputs V2P and V2N are connected to ADC 1 and the

analog inputs V1P and V1N are connected to ADC 2.

12, 11

14, 13

15

DTRT1, 0

WAVSEL1, 0

TEST1

These bits are used to select the waveform register update rate.

DTRT1

DTRT0

Update Rate

0

1

0

1

0

1

27.9 kSPS (CLKIN/128)

14 kSPS (CLKIN/256)

7 kSPS (CLKIN/512)

3.5 kSPS (CLKIN/1024)

These bits are used to select the source of the sampled data for the waveform register.

WAVSEL1, 0

Length

24 bits

40 bits

24 bits

Source

0

1

0

1

0

1

Active Power Signal (output of LPF2)

Channel 1 and Channel 2

Channel 1

Channel 2

Writing a Logic 1 to this bit position places the ADE7759 in test mode. This is intended for fac-

tory testing only and should be left at 0.

REV. A

–31–

ADE7759

15 14 13 12 11 10

9

0

8

0

7

0

6

0

5

0

4

0

3

1

2

1

0

ADDR: 06H

DISHPF

TEST1

(TEST MODE SELECTION SHOULD BE SET TO 0)

(DISABLE HPF1 IN CHANNEL 1)

WAVSEL

DISLPF2

(WAVEFORM SELECTION FOR SAMPLE MODE)

(DISABLE LPF2 AFTER MULTIPLIER)

00 = LPF2

DISCF

01 = CH1 + CH2 (40-BIT WAVEFORM SAMPLES)

(DISABLE FREQUENCY OUTPUT CF)

10 = CH1

11 = CH2

DISSAG

(DISABLE SAG OUTPUT)

DTRT

(WAVEFORM SAMPLES OUTPUT DATA RATE)

00 = 27.9kSPS (CLKIN/128)

ASUSPEND

(SUSPEND CH1 AND CH2 ADCs)

01 = 14.4kSPS (CLKIN/256)

10 = 7.2kSPS (CLKIN/512)

11 = 3.6kSPS (CLKIN/1024)

STEMP

(START TEMPERATURE SENSING)

SWRST

(SOFTWARE CHIP RESET)

SWAP

CYCMODE

(SWAP CH1 AND CH2 ADCs)

(LINE CYCLE ENERGY ACCUMULATION MODE)

DISCH2

(SHORT THE ANALOG INPUTS ON CHANNEL 2)

DISCH1

(SHORT THE ANALOG INPUTS ON CHANNEL 1)

NOTE: REGISTER CONTENTS SHOW POWER-ON DEFAULTS

Figure 48. Mode Register

Interrupt Status Register (04H)/Reset Interrupt Status Register (05H)

The status register is used by the MCU to determine the source of an interrupt request (IRQ). When an interrupt event occurs in the

ADE7759, the corresponding flag in the interrupt status register is set logic high. If the enable bit for this flag is Logic 1 in the inter-

rupt enable register, the IRQ logic output goes active low. When the MCU services the interrupt, it must first carry out a read from

the interrupt status register to determine the source of the interrupt.

Table VII. Interrupt Status Register, Reset Interrupt Status Register, and Interrupt Enable Register

Bit

Location

Interrupt

Flag

Description

0

1

2

AEHF

Indicates that an interrupt was caused by the 0 to 1 transition of the MSB of the active energy register.

Indicates that an interrupt was caused by a SAG on the line voltage or no zero crossings were detected.

SAG

CYCEND

Indicates the end of energy accumulation over an integer number of half line cycles as defined by

the content of the LINECYC register—see Line Cycle Energy Accumulation Mode section.

3

4

5

6

WSMP

ZX

Indicates that new data is present in the waveform register.

This status bit reflects the status of the ZX logic output—see Zero Crossing Detection section.

Indicates that a temperature conversion result is available in the temperature register.

TEMP

RESET

Indicates the end of a reset (for both software or hardware reset). The corresponding enable bit has

no function in the interrupt enable register, i.e., this status bit is set at the end of a reset, but it

cannot be enabled to cause an interrupt.

7

AEOF

Indicates that the active energy register has overflowed.

–32–

REV. A

ADE7759

7

0

6

1

5

0

4

0

3

0

2

0

1

0

ADDR: 04H/RESET: 05H

AEOF

AEHF

(ACTIVE ENERGY REGISTER OVERFLOW)

(ACTIVE ENERGY REGISTER HALF FULL)

SAG

RESET

(LINE VOLTAGE SAG DETECT)

(END OF A HARDWARE OR SOFTWARE RESET)

TEMP

CYCEND

(TEMPERATURE REGISTER READY)

(LINE CYCLE ENERGY ACCUMULATION END)

ZX

WSMP

(ZERO CROSSING DETECTED)

(WAVEFORM SAMPLING)

NOTE: REGISTER CONTENTS SHOW POWER ON DEFAULTS

Figure 49. Interrupt Status Register

7

0

6

0

5

0

4

0

3

0

2

0

1

0

ADDR: 10H

AEHF

AEOF

(ACTIVE ENERGY REGISTER OVERFLOW)

(ACTIVE ENERGY REGISTER HALF FULL)

NOT USED

SAG

(LINE VOLTAGE SAG DETECT)

TEMP

CYCEND

(TEMPERATURE REGISTER READY)

(END OF LINE CYCLE ENERGY ACCUMULATION)

ZX

WSMP

(ZERO CROSSING DETECTED)

(WAVEFORM SAMPLING)

NOTE: REGISTER CONTENTS SHOW POWER ON DEFAULTS

Figure 50. Interrupt Enable Register

CH1OS Register (08H)

The CH1OS register is an 8-bit, read/write enabled register. The MSB of this register is used to switch on/off the digital integrator in Chan-

nel 1, and Bits 0 to 5 indicate the amount of the offset correction in Channel 1. Table VIII summarizes the function of this register.

Table VIII. CH1OS Register

Bit Location

Bit Mnemonic

Description

0 to 5

OFFSET

The six LSBs of the CH1OS register control the amount of dc offset correction in Channel 1

ADC. The 6-bit offset correction is sign and magnitude coded. Bits 0 to 4 indicate the magnitude

of the offset correction. Bit 5 shows the sign of the offset correction. A 0 in Bit 5 means the offset

correction is positive and a 1 indicates the offset correction is negative.

6

7

Not Used

This bit is unused.

INTEGRATOR

This bit is used to activate the digital integrator on Channel 1. The digital integrator is switched

on by setting this bit. This bit is set to be 1 on default.

CH1OS REGISTER*

7

1

6

0

5

0

4

0

3

0

2

0

1

0

ADDR: 08H

SIGN AND MAGNITUDE CODED

DIGITAL INTEGRATOR SELECTION

1 = ENABLE

0 = DISABLE

OFFSET CORRECTION BITS

NOT USED

*REGISTER CONTENTS SHOW POWER-ON DEFAULT

Figure 51. CH1OS Register

REV. A

–33–

ADE7759

OUTLINE DIMENSIONS

20-Lead Shrink Small Outline Package [SSOP]

(RS-20)

Dimensions shown in millimeters

7.50

7.20

6.90

20

11

10

8.20

7.80

7.40

5.60

5.30

5.00

1

1.85

1.75

1.65

2.00 MAX

0.25

0.09

8ꢀ

4ꢀ

0ꢀ

0.65

BSC

0.95

0.75

0.55

0.38

0.22 SEATING

PLANE

0.05 MIN

COPLANARITY

0.10

COMPLIANT TO JEDEC STANDARDS MO-150AE

–34–

REV. A

ADE7759

Revision History

Location

Page

12/02—Data Sheet changed from REV. 0 to REV. A.

Changes to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Changes to Figure 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

REV. A

–35–

–36–


型号：	ADE7759ARSZ
厂家：	Rochester Electronics
描述：	SPECIALTY ANALOG CIRCUIT, PDSO20, SSOP-20 光电二极管
文件：	总37页 (文件大小：1441K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

ADE7759ARSZ [ROCHESTER]

相关型号：

ADE7760

ADE7760ARS

ADE7760ARSRL

ADE7761

ADE7761A

ADE7761AARS

ADE7761AARS-REF

ADE7761AARS-RL

ADE7761AARSZ

ADE7761AARSZ-RL

ADE7761ARS

ADE7761ARS-REF