FIRETRAP-RX [RFSOLUTIONS]
FIRETRAP;
RFSOLUTIONS.LTD 
FIRETRA
Features
Rugged radio remote control
One Transmiꢁer can control many receivers
Waterproof receiver to IP68
Transmiꢁers available with 1, 2, 3, 4, 16 Switches
Descripꢀon
Supplied ready to operate the FIRETRAP system is designed for conꢀnuous operaꢀon 365
days of the year. This system incorporates IP68 rated enclosures with ‘resin dipped’ circuit
boards for protecꢀon against condensaꢀon.
Each receiver has four independent outputs which can easily be paired with individual
switches from one or many transmiꢁers. Building a bespoke control system is easy with
transmiꢁers containing up to 16 switches.
DS FIRETRAP-8
FIRETRAP
System and Receiver Part Numbers
Range**
(Metres)
Frequency
(MHz)
Part Number
FIRETRAP-S1PRM
FIRETRAP-S1LAP
FIRETRAP-S1AS1
Descripꢀon
System 1 ch Prewired for Promaꢀc
(Duraplug)
433.92
433.92
433.92
250
250
250
System 1 ch Prewired for
Laporte
System 1 ch Prewired for Au-
toSporter
FIRETRAP-S1
FIRETRAP-RX
System 1 channel
Receiver Unit only
433.92
433.92
250
250
Skeet Systems
Part Number
Range**
(Metres)
Frequency
(MHz)
Descripꢀon
FIRETRAP-SKEET
Skeet System (TX & 2 x RX’s)
433.92
250
Part Number
Descripꢀon
FIRETRAP-TX1
Transmiꢁer 1 switch
Skeet Transmiꢁer 3 switch
FIRETRAP-TX3
FIRETRAP-TX4
Transmiꢁer 4 switch
FIRETRAP-TX16
FIREFLY -TX-IPKIT
Transmiꢁer 16 switch (8Sw + Shiꢂ Key)
’O’ Ring, Seals Transmiꢁer to IP68
Transmiꢁers ship with; Wall Mounꢀng Cradle, and Lanyard
FIRETRAP
PLEASE READ BEFORE ATTEMPTING INSTALLATION:
This system is supplied complete with cable in order to connect to the Clay Trap Release.
Warning : Not all Clay Traps have the same wiring convenꢀon!
The system is pre-wired (as diagram below) to operate with most trap releases, before connecꢀng, CHECK
YOUR CONNECTIONS. (using a voltmeter) if you are in any doubt, DO NOT CONNECT THE SYSTEM, consult a
qualified Electrician. Although the system operates on 12-30V DC damage may occur to the receiver unit if
wrong connecꢀons are made.
Installaꢀon Notes
An ideal installaꢀon would be to firmly fix the FIRETRAP-RX approx. 2 metres from the ground, in direct sight
of the transmiꢁer. Lowering the height or having obstacles between transmiꢁer and receiver will reduce
range!
Connecꢀng Power to the Receiver unit
The receiver unit requires the following connecꢀons to operate:
- 12V supply (Brown wire as supplied)
- OV Supply (Yell/GRN wire as supplied)
When the Receiver unit has power connected the Power LED will illuminate. This must be ‘on’ for the system
to operate.
Note:
If you are pairing mulꢀple transmiꢁer i.e. If you have purchased receivers and transmiꢁers separately. Follow
the procedure detailed on page 4 to configure your chosen system. FIRETRAP-S1 systems are sold pre-paired.
ANTENNA
BUZZER
REED SWITCH
LRN SWITCH
ACK LED
LRN LED
JUMPER LINKS
PWR LED
Relay 1
Relay 2
Relay 3
NO
COM
NC
FIRETRAP Receiver Wiring
This diagram shows the standard
wiring configuration and may be
adapted to fit Traps requiring other
switching types.
12V
0V
FIRETRAP
Check the Wiring required for your Trap:
The FIRETRAP is capable of switching nearly any trap type, however wiring convenꢀons vary between
manufacturers. The relays on the FIRETRAP can switch up to 24V DC or 230V AC @ 5A.
Addiꢀonal Transmiꢁers
Each transmiꢁer has a unique idenꢀty. Each ꢀme a transmiꢁer switch is operated, it transmits a secure
RF signal. The Receiver can to set learn this signal and pair it to any of its outputs.
To pair a New Transmiꢁer switch follow this procedure:
Any transmiꢁer buꢁon can be paired to one or many of the receiver output relays.
Each buꢁon must be paired to each relay individually by following this procedure:
Select the receiver output relay to pair:
1.
2.
3.
Briefly press the receiver pairing switch (S2) once.
The Receiver pairing LED will flash once to indicate output relay 1 is selected.
Aꢂer the Receiver pairing LED stops flashing, press the receiver pairing switch again to select the
next relay.
4.
5.
6.
Repeat step 2 unꢀl the required output relay is selected.
Press the buꢁon on the transmiꢁer you want to pair to the selected relay.
The receiver pairing LED will Flash once to confirm pairing is complete.
Erasing Receivers Memory
Press and hold the receiver pairing switch for approx 10 seconds.
Release the switch and watch for the receiver LED to flash to confirm erasing.
Press a buꢁon on the transmiꢁer and ensure no relay acꢀves
NOTE: You cannot erase individual transmiꢁers or buꢁons
Configuring Receiver Relays
The link caps (shown above) configure the outputs operaꢀon. The these links are connected/broken us-
ing the small link cap placed over the pins. To “store” the seꢃng turn power off then back on.
Link Posiꢀons
Relay Outputs
LK1
LK2
RLY 1
RLY 2
RLY 3
RLY 4
Open
Closed
Open
Open
Open
Closed
1/2 sec Mom
1/2 sec Mom
Mom
1/2 sec Mom
Mom
1/2 sec Mom
Mom
1/2 sec Mom
Mom
Mom
Mom
Mom
Closed
Closed
-
-
-
FIRETRAP
Technical Specificaꢀons
Transmiꢁers: FIRETRAP-TXn
Enclosure Raꢀng:
Baꢁery Type:
Dimensions:
Standard IPx8
CR2032 (supplied)
90 x 54 x 27 mm
ELECTRICAL CHARACTERISICS
Supply Voltage
MIN
TYPICAL
3V
MAX
UNITS
V
Supply Current
mA
Frequency:
FIREFLY: Wideband
433.10
433.920
3
434.70
10
MHz
mW
RF Output Power (ERP) @ 433 MHz
-
Receiver: FIRETRAP-RX
Enclosure Raꢀng:
Dimensions:
Storage Temperature:
Operaꢀng Temperature:
IP68
130 x 112 x 42 mm (not including antenna)
-10 to +70o Celsius.
-10 to +50o Celsius.
ELECTRICAL CHARACTERISTICS
Supply Voltage for +12 v
MIN
10.5
TYPICAL
5
MAX
30
DIMENSION
Vdc
A
Relay Raꢀng* (230Vac) RLY1-4
12
Supply Current :
Quiescent
All relays operaꢀng*
10
140
mA
mS
Time delay from Tx on switch to Rx Relay operaꢀon
Time delay from Tx sw relax to Rx Relay release
100
300
MS
*The relay contacts in this unit are for funcꢀonal use only and must not be used for isolaꢀon purposes
Is a trade name of R F Solutions Ltd
William alexander house, William way,
Burgess Hill, West Sussex,
RH15 9AG
Email : sales@rfsolutions.co.uhttp://www.rfsolutions.co.u
Tel: +44 (0)1444 22790
Fax: +44 (0)1444 22789
FIRETRAP
Mechanical Dimensions
50.00
All Dimensions in mm
82.00
RF Soluꢀons Ltd. Recycling Noꢀce
Meets the following EC Direcꢀves:
DO NOT
Discard with normal waste, please recycle.
Waste Baꢁeries and Accumulators
Direcꢀve 2006/66/EC
ROHS Direcꢀve 2002/95/EC
Specifies certain limits for hazardous substances.
Where baꢁeries are fiꢁed, before recycling the prod-
uct, the baꢁeries must be removed and disposed of
at a licensed collecꢀon point.
WEEE Direcꢀve 2002/96/EC
Waste electrical & electronic equipment. This product must be
disposed of through a licensed WEEE collecꢀon point.
RF Soluꢀons Ltd., fulfils its WEEE obligaꢀons by membership
Environment Agency producer registraꢀon number:
WEE/JB0104WV.
Disclaimer:
Whilst the informaꢀon in this document is believed to be correct at the ꢀme of issue, RF Soluꢀons Ltd does not accept any liability whatsoever for its accuracy, adequacy or completeness. No express
or implied warranty or representaꢀon is given relaꢀng to the informaꢀon contained in this document. RF Soluꢀons Ltd reserves the right to make changes and improvements to the product(s)
described herein without noꢀce. Buyers and other users should determine for themselves the suitability of any such informaꢀon or products for their own parꢀcular requirements or specificaꢀon(s).
RF Soluꢀons Ltd shall not be liable for any loss or damage caused as a result of user’s own determinaꢀon of how to deploy or use RF Soluꢀons Ltd’s products. Use of RF Soluꢀons Ltd products or
components in life support and/or safety applicaꢀons is not authorised except with express wriꢁen approval. No licences are created, implicitly or otherwise, under any of RF Soluꢀons Ltd’s intellec-
tual property rights. Liability for loss or damage resulꢀng or caused by reliance on the informaꢀon contained herein or from the use of the product (including liability resulꢀng from negligence or
where RF Soluꢀons Ltd was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict RF Soluꢀons Ltd’s liability for death or personal injury resulꢀng
from its negligence.
相关型号：
©2020 ICPDF网 联系我们和版权申明