ISL89164FRTBZ [RENESAS]
High Speed, Dual Channel, 6A, Power MOSFET Driver with Enable Inputs;型号: | ISL89164FRTBZ |
厂家: | RENESAS TECHNOLOGY CORP |
描述: | High Speed, Dual Channel, 6A, Power MOSFET Driver with Enable Inputs |
文件: | 总16页 (文件大小:757K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATASHEET
ISL89163, ISL89164, ISL89165
High Speed, Dual Channel, 6A, Power MOSFET Driver with Enable Inputs
FN7707
Rev 5.00
October 13, 2016
The ISL89163, ISL89164, and ISL89165 are high-speed, 6A,
Features
dual channel MOSFET drivers with enable inputs. These parts
• Dual output, 6A peak currents, can be paralleled
are very similar to the ISL89160, ISL89161, ISL89162 drivers
but with an added enable input for each channel occupying NC
pins 1 and 8 of the ISL89160, ISL89161, ISL89162.
• Dual AND-ed input logic, (INput and ENable)
• Typical ON-resistance <1Ω
Precision thresholds on all logic inputs allow the use of
external RC circuits to generate accurate and stable time
delays on both the main channel inputs, INA and INB, and the
enable inputs, ENA and ENB. The precision delays capable of
these precise logic thresholds makes these parts very useful
for dead-time control and synchronous rectifiers. Note that the
ENable and INput logic inputs can be interchanged for
alternate logic implementations.
• Specified Miller plateau drive currents
• Very low thermal impedance ( = 3°C/W)
JC
• Hysteretic Input logic levels for 3.3V CMOS, 5V CMOS, TTL,
and Logic levels proportional to V
DD
• Precision threshold inputs for time delays with external RC
components
• 20ns rise and fall time driving a 10nF load.
Three input logic thresholds are available: 3.3V (CMOS), 5.0V
(CMOS or TTL compatible), and CMOS thresholds that are
proportional to VDD.
Applications
• Synchronous Rectifier (SR) driver
• Switch mode power supplies
• Motor drives, Class D amplifiers, UPS, inverters
• Pulse transformer driver
At high switching frequencies, these MOSFET drivers use very
little internal bias currents. Separate, non-overlapping drive
circuits are used to drive each CMOS output FET to prevent
shoot-through currents in the output stage.
The start-up sequence is designed to prevent unexpected
• Clock/line driver
glitches when V is being turned on or turned off. When V
DD
DD
< ~1V, an internal 10kΩ resistor between the output and
ground helps to keep the output voltage low. When ~1V < V
< UV, both outputs are driven low with very low resistance and
the logic inputs are ignored. This insures that the driven FETs
Related Literature
• For a full list of related documents, visit our web page
• ISL89163, ISL89164, ISL89165 product pages
DD
are off. When V > UVLO, and after a short delay, the outputs
DD
now respond to the logic inputs.
3.0
POSITIVE THRESHOLD LIMITS
V
DD
2.5
2.0
ENB
ENA
1
2
3
4
8
INA
OUTA
7
6
5
EPAD
GND
1.5
NEGATIVE THRESHOLD LIMITS
INB
OUTB
1.0
0.5
0.0
4.7µF
-40 -25 -10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
FIGURE 1. TYPICAL APPLICATION
FIGURE 2. TEMP STABLE LOGIC THRESHOLDS
FN7707 Rev 5.00
October 13, 2016
Page 1 of 16
ISL89163, ISL89164, ISL89165
Block Diagram
VDD
FOR OPTIONS A AND B, THE UV
COMPARATOR HOLDS OFF THE
OUTPUTS UNTIL VDD~> 3.3VDC.
FOR OPTION C, THE UV
SEPARATE FET DRIVES, WITH NON-
OVERLAPPING OUTPUTS, PREVENT
SHOOT-THRU CURRENTS IN THE OUTPUT
CMOS FETS RESULTING WITH VERY LOW
HIGH FREQUENCY OPERATING
CURRENTS.
FOR CLARITY, ONLY ONE
CHANNEL IS SHOWN
RELEASE IS~> 6.5V
ENx
ISL89163
ENX AND INX INPUTS ARE
IDENTICAL AND MAY BE
INTERCHANGED FOR
ALTERNATE LOGIC
OUTx
INx
10k
ISL89164, ISL89165
GND
EPAD
FOR PROPER THERMAL AND ELECTRICAL
PERFORMANCE, THE EPAD MUST BE
CONNECTED TO THE PCB GROUND PLAN.E
FIGURE 3. BLOCK DIAGRAM
Pin Configurations
Pin Descriptions
DESCRIPTION
(SEE TRUTH TABLE FOR
LOGIC POLARITIES)
ISL89163FR, ISL89163FB
(8 LD TDFN, EPSOIC)
TOP VIEW
ISL89164FR, ISL89164FB
(8 LD TDFN, EPSOIC)
TOP VIEW
PIN
NUMBER
SYMBOL
ENA
1
2
3
4
5
6
7
8
Channel A enable, 0V to VDD
ENA
INA
1
2
3
4
8
7
6
5
ENB
ENA
/INA
GND
/INB
1
2
3
4
8
7
6
5
ENB
INA, /INA Channel A input, 0V to VDD
GND Power Ground, 0V
INB, /INB Channel B enable, 0V to VDD
OUTA
VDD
OUTA
VDD
GND
INB
OUTB
OUTB
OUTB
VDD
Channel B output
Power input, 4.5V to 16V
Channel A output, 0V to VDD
Channel B enable, 0V to VDD
Power Ground, 0V
ISL89165FR, ISL89165FB
(8 LD TDFN, EPSOIC)
TOP VIEW
OUTA
ENB
EPAD
ENA
/INA
GND
INB
1
2
3
4
8
7
6
5
ENB
OUTA
VDD
ENx
INx
ENx
OUTx
OUTx
/INx
OUTB
NON-INVERTING
INVERTING
ENx* /INx*
UV
0
ENx*
INx*
OUTx*
UV
OUTx*
x
0
1
1
0
0
1
1
x
1
0
1
0
1
0
1
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
0
0
0
0
0
1
0
0
0
0
1
1
1
1
*SUBSTITUTE A OR B FOR x
FN7707 Rev 5.00
October 13, 2016
Page 2 of 16
ISL89163, ISL89164, ISL89165
Ordering Information
PART NUMBER
PART
TEMP
RANGE (°C)
INPUT
CONFIGURATION
INPUT
LOGIC
PACKAGE
(RoHS COMPLIANT)
PKG.
DWG. #
(Notes 3, 4)
MARKING
ISL89163FRTAZ (Note 1)
ISL89163FRTBZ (Note 1)
ISL89164FRTAZ (Note 1)
ISL89164FRTBZ (Note 1)
ISL89165FRTAZ (Note 1)
ISL89165FRTBZ (Note 1)
ISL89163FBEAZ (Note 2)
ISL89163FBEBZ (Note 2)
ISL89164FBEAZ (Note 2)
ISL89164FBEBZ (Note 2)
ISL89165FBEAZ (Note 2)
ISL89165FBEBZ (Note 2)
NOTES:
163A
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
Non-inverting
Inverting
3.3V 8 Ld 3x3 TDFN
5.0V 8 Ld 3x3 TDFN
3.3V 8 Ld 3x3 TDFN
5.0V 8 Ld 3x3 TDFN
3.3V 8 Ld 3x3 TDFN
5.0V 8 Ld 3x3 TDFN
3.3V 8 Ld EPSOIC
5.0V 8 Ld EPSOIC
3.3V 8 Ld EPSOIC
5.0V 8 Ld EPSOIC
3.3V 8 Ld EPSOIC
5.0V 8 Ld EPSOIC
L8.3x3I
163B
L8.3x3I
L8.3x3I
L8.3x3I
L8.3x3I
L8.3x3I
M8.15D
M8.15D
M8.15D
M8.15D
M8.15D
M8.15D
164A
164B
165A
Inverting +
Non-inverting
165B
89163 FBEAZ
89163 FBEBZ
89164 FBEAZ
89164 FBEBZ
89165 FBEAZ
89165 FBEBZ
Non-inverting
Inverting
Inverting +
Non-inverting
1. Add “-T”, suffix for 6k unit tape and reel. Refer to TB347 for details on reel specifications.
2. Add “-T”, suffix for 2.5k unit tape and reel. Refer to TB347 for details on reel specifications.
3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
4. Input Logic Voltage: A = 3.3V, B = 5.0V.
5. For Moisture Sensitivity Level (MSL), see device information page for ISL89163, ISL89164, ISL89165. For more information on MSL, see Technical
Brief TB363.
TABLE 1. KEY DIFFERENCES BETWEEN FAMILY OF PARTS
I/O PINS
PART NUMBER
ISL89163
ENA
NINV
NINV
NINV
ENB
NINV
NINV
NINV
INA
NINV
INV
INB
NINV
INV
OUTA
NINV
NINV
NINV
OUTB
NINV
NINV
NINV
ISL89164
ISL89165
INV
NINV
NOTE: INV: Inverting Input, NINV: Non-inverting input.
FN7707 Rev 5.00
October 13, 2016
Page 3 of 16
ISL89163, ISL89164, ISL89165
Absolute Maximum Ratings
Thermal Information
Supply Voltage, VDD Relative to GND . . . . . . . . . . . . . . . . . . . -0.3V to 18V
Thermal Resistance (Typical)
8 Ld TDFN Package (Notes 6, 7). . . . . . . . .
8 Ld EPSOIC Package (Notes 6, 7). . . . . . .
(°C/W)
44
42
(°C/W)
JC
JA
Logic Inputs (INA, INB, ENA, ENB) . . . . . . . . . . . . GND - 0.3v to V + 0.3V
3
3
DD
Outputs (OUTA, OUTB) . . . . . . . . . . . . . . . . . . . . . . GND - 0.3v to V + 0.3V
DD
Average Output Current (Note 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150mA
ESD Ratings
Human Body Model Class 2 (Tested per JESD22-A114E) . . . . . . 2000V
Machine Model Class B (Tested per JESD22-A115-A) . . . . . . . . . . 200V
Charged Device Model Class IV . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000V
Latch-Up
Max Power Dissipation at +25°C in Free Air . . . . . . . . . . . . . . . . . . . . . 2.27W
Max Power Dissipation at +25°C with Copper Plane . . . . . . . . . . . . .33.3W
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Maximum Operating Junction Temp Range . . . . . . . . . . .-40°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493
(Tested per JESD-78B; Class 2, Level A)
Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mA
Recommended Operating Conditions
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
Options A and B
Supply Voltage, VDD Relative to GND . . . . . . . . . . . . . . . . . . .4.5V to 16V
Logic Inputs (INA, INB, ENA, ENB) . . . . . . . . . . . . . . . . . . . . . . 0V to VDD
Outputs (OUTA, OUTB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to VDD
Option C
Supply Voltage, VDD Relative to GND . . . . . . . . . . . . . . . . . . .7.5V to 16V
Logic Inputs (INA, INB, ENA, ENB) . . . . . . . . . . . . . . . . . . . . . . 0V to VDD
Outputs (OUTA, OUTB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to VDD
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
6. is measured in free air with the component mounted on a high-effective thermal conductivity test board with “direct attach” features. See Tech
JA
Brief TB379 for details.
7. For , the “case temp” location is the center of the exposed metal pad on the package underside.
JC
8. The average output current, when driving a power MOSFET or similar capacitive load, is the average of the rectified output current. The peak output
currents of this driver are self limiting by trans conductance or r
and do not required any external components to minimize the peaks. If the
DS(ON)
output is driving a non-capacitive load, such as an LED, maximum output current must be limited by external means to less than the specified
absolute maximum.
DC Electrical Specifications
V
= 12V, GND = 0V, No load on OUTA or OUTB, unless otherwise specified. Boldface limits apply across
DD
the operating junction temperature range, -40°C to +125°C.
T = +25°C
J
T = -40°C to +125°C
J
MIN
MAX
PARAMETERS
POWER SUPPLY
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
(Note 9)
(Note 9)
UNIT
Voltage Range (Option A and B)
Voltage Range (Option C)
V
V
-
-
-
-
-
-
-
-
-
4.5
16
V
DD
DD
DD
7.5
16
V
V
Quiescent Current
I
ENx = INx = GND
5
-
-
-
-
mA
mA
DD
INA = INB = 1MHz, square wave
25
UNDERVOLTAGE
VDD Undervoltage Lock-out
(Options A and B) (Note 13,
Figure 10)
V
V
ENA = ENB = True
INA = INB = True
-
-
3.3
6.5
-
-
-
-
-
-
V
V
UV
UV
VDD Undervoltage Lock-out
ENA = ENB = True
(Option C) (Note 13, Figure 10)
INA = INB = True (Note 9)
Hysteresis (Option A or B)
Hysteresis (Option C)
-
-
~25
-
-
-
-
-
-
mV
V
~0.95
FN7707 Rev 5.00
October 13, 2016
Page 4 of 16
ISL89163, ISL89164, ISL89165
DC Electrical Specifications
V
= 12V, GND = 0V, No load on OUTA or OUTB, unless otherwise specified. Boldface limits apply across
DD
the operating junction temperature range, -40°C to +125°C. (Continued)
T = +25°C
J
T = -40°C to +125°C
J
MIN
MAX
PARAMETERS
SYMBOL
TEST CONDITIONS
MIN
-
TYP
-
MAX
-
(Note 9)
(Note 9)
UNIT
V
INPUTS
Input Range
for INA, INB, ENA, ENB
V
Option A, B, or C
IN
GND
V
DD
Logic 0 Threshold
for INA, INB, ENA, ENB
(Note 12)
V
Option A, nominally 37% x 3.3V
Option B, nominally 37% x 5.0V
-
-
-
1.22
1.85
2.4
-
-
-
1.12
1.70
2.00
1.32
2.00
2.76
V
V
V
IL
Option C, nominally 20% x 12V
(Note 10)
Logic 1 Threshold
for INA, INB, ENA, ENB
(Note 12)
V
Option A, nominally 63% x 3.3V
Option B, nominally 63% x 5.0V
-
-
-
2.08
3.15
9.6
-
-
-
1.98
3.00
9.24
2.18
3.30
9.96
V
V
V
IH
Option C, nominally 80% x 12V
(Note 10)
Input Capacitance of INA, INB,
ENA, ENB (Note 11)
C
-
-
2
-
-
-
-
-
pF
IN
IN
Input Bias Current
I
GND < V < V
IN
-10
+10
µA
DD
for INA, INB, ENA, ENB
OUTPUTS
High Level Output Voltage
Low Level Output Voltage
V
V
-
-
-
-
-
-
V
- 0.1
V
DD
V
V
OHA OHB
DD
V
V
GND
GND + 0.1
OLA
OLB
Peak Output Source Current
Peak Output Sink Current
NOTES:
I
I
V
V
(initial) = 0V, C
LOAD
= 10nF
= 10nF
-
-
-6
-
-
-
-
-
-
A
A
O
O
O
(initial) = 12V, C
+6
O
LOAD
9. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
10. The nominal 20% and 80% thresholds for option C are valid for any value within the specified range of VDD.
11. This parameter is taken from the simulation models for the input FET. The actual capacitance on this input will be dominated by the PCB parasitic
capacitance.
12. The true state input voltage for the non-inverted inputs is greater than the Logic 1 threshold voltage. The true state input voltage for the inverted
inputs is less than the logic 0 threshold voltage.
13. A 400µs delay further inhibits the release of the output state when the UV positive going threshold is crossed. See Figure 10 on page 8.
FN7707 Rev 5.00
October 13, 2016
Page 5 of 16
ISL89163, ISL89164, ISL89165
AC Electrical Specifications
V
= 12V, GND = 0V, No Load on OUTA or OUTB, unless otherwise specified. Boldface limits apply over
DD
the operating junction temperature range, -40°C to +125°C.
T = +25°C
T = -40°C to +125°C
J
J
PARAMETERS
SYMBOL TEST CONDITIONS /NOTES
= 10nF,
MIN
-
TYP MAX
MIN
-
MAX
UNIT
ns
Output Rise Time (see Figure 5)
t
C
20
-
40
R
LOAD
10% to 90%
Output Fall Time (see Figure 5)
t
C
= 10nF, 90% to 10%
-
-
20
25
-
-
-
-
40
50
ns
ns
F
LOAD
Output Rising Edge Propagation Delay for
Non-Inverting Inputs (Note 14)
(see Figure 4)
t
V = 12V
RDLYn
DD
Options A and B
V
= 8V
-
-
-
-
-
-
-
25
25
25
25
25
25
25
-
-
-
-
-
-
-
-
-
-
-
-
-
-
50
50
50
50
50
50
50
ns
ns
ns
ns
ns
ns
ns
DD
Option C
Output Rising Edge Propagation Delay with
Inverting Inputs (Note 14)
(see Figure 4)
t
V
= 12V
RDLYi
DD
Options A and B
V
= 8V
DD
Option C
Output Falling Edge Propagation Delay with
Non-Inverting Inputs (Note 14)
(see Figure 4)
t
V
= 12V
FDLYn
DD
Options A and B
V
= 8V
DD
Option C
Output Falling Edge Propagation Delay with
Inverting Inputs (Note 14)
(see Figure 4)
t
V
= 12V
FDLYi
DD
Options A and B
V
= 8V
DD
Option C
No load
No load
Rising Propagation Matching (see Figure 4)
Falling Propagation Matching (see Figure 4)
t
-
-
-
<1
<1
6
-
-
-
-
-
-
-
-
-
ns
ns
A
RM
t
FM
Miller Plateau Sink Current
(See Test Circuit Figure 6)
-I
V
V
= 10V,
MP
DD
MILLER
= 5V
-I
-I
V
V
V
V
V
= 10V, V
= 10V, V
= 10V, V
= 10V, V
= 10V, V
= 3V
= 2V
= 5V
= 3V
= 2V
-
-
-
-
-
4.7
3.7
5.2
5.8
6.9
400
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
A
A
MP
MP
MP
MP
MP
DD
DD
DD
DD
DD
MILLER
MILLER
MILLER
MILLER
MILLER
Miller Plateau Source Current
(See Test Circuit Figure 7)
I
I
I
A
A
A
Turn On Delay
(Note 13, Figure 10)
T
see Figure 10
µs
on_delay
NOTE:
14. Propagation delays for option C are typically the same for the recommended operating range (7.5V ≤ V ≤ 16V).
DD
FN7707 Rev 5.00
October 13, 2016
Page 6 of 16
ISL89163, ISL89164, ISL89165
Test Waveforms and Circuits
V
DD
80%
Option C
INA, INB,
ENA, ENB
20%
0V
3.3V Option A
5.0V Option B
50%
50%
Option A or B
INA, INB,
ENA, ENB
0V
90%
10%
tRDLY
tFDLY
/OUTA
OUTA
OUTA
OR
tRDLY
tFDLY
OUTB
/OUTB
OUTB
tR
tF
tRM
tFM
LOGIC LEVELS: OPTION A = 3.3V, OPTION B = 5.0V, OPTION C = V
DD
FIGURE 4. PROP DELAYS AND MATCHING
FIGURE 5. RISE/FALL TIMES
10V
10V
ISL8916x
ISL8916x
0.1µF
10k
0.1µF
10nF
10k
VMILLER
VMILLER
10µF
10µF
200ns
200ns
10nF
+ISENSE
+ISENSE
50m
50m
-ISENSE
-ISENSE
FIGURE 6. MILLER PLATEAU SINK CURRENT TEST CIRCUIT
FIGURE 7. MILLER PLATEAU SOURCE CURRENT TEST CIRCUIT
10V
0A
CURRENT THROUGH 0.1
IMP
RESISTOR
VMILLER
VOUT
VOUT
VMILLER
CURRENT THROUGH 0.1
-IMP
RESISTOR
0
0V
200ns
200ns
FIGURE 8. MILLER PLATEAU SINK CURRENT
FIGURE 9. MILLER PLATEAU SOURCE CURRENT
FN7707 Rev 5.00
October 13, 2016
Page 7 of 16
ISL89163, ISL89164, ISL89165
Test Waveforms and Circuits
RISING VDD
THIS DURATION IS
DEPENDANT ON RISE TIME
OF VDD
UV THRESHOLD
THIS DURATION IS
INDEPENDENT ON
RISE TIME OF V
DD
~1V
10k to
GROUND
OUTPUTS
ACTIVE LOW
OUTA, OUTB
OUTPUT STATE
OUTPUTS CONTROLLED BY
LOGICAL INPUTS
400µs TYPICAL
(Ton_delay
)
<1 to GROUND
FIGURE 10. START-UP OUTPUT CHARACTERISTIC
Typical Performance Curves
3.5
35
30
25
20
15
10
5
+125°C
+125°C
+25°C
3.0
-40°C
+25°C
-40°C
2.5
2.0
4
8
12
16
4
8
12
16
V
V
DD
DD
FIGURE 11. I vs V (STATIC)
DD DD
FIGURE 12. I vs V (1MHz)
DD DD
FN7707 Rev 5.00
October 13, 2016
Page 8 of 16
ISL89163, ISL89164, ISL89165
Typical Performance Curves(Continued)
50
1.1
1.0
16V
V
LOW
HIGH
OUT
40
30
20
10
0
NO LOAD
0.9
0.8
0.7
10V
5V
V
OUT
12V
0.6
0.5
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
FREQUENCY (MHz)
-45
-20
5
30
55
80
105
130
TEMPERATURE (°C)
FIGURE 13. I vs FREQUENCY (+25°C)
DD
FIGURE 14. r
vs TEMPERATURE
DS(ON)
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
POSITIVE THRESHOLD
NEGATIVE THRESHOLD
POSITIVE THRESHOLD
NEGATIVE THRESHOLD
-45
-20
5
30
55
80
105
130
-45
-20
5
30
55
80
105
130
TEMPERATURE (°C)
TEMPERATURE (°C)
FIGURE 15. OPTION A THRESHOLDS
FIGURE 16. OPTION B THRESHOLDS
25
30
25
FALL TIME, C
= 10nF
LOAD
OUTPUT FALLING PROP DELAY
OUTPUT RISING PROP DELAY
20
RISE TIME, C
= 10nF
LOAD
20
15
15
-45
-20
5
30
55
80
105
130
5
7
9
11
DD
13
15
V
TEMPERATURE (°C)
FIGURE 17. OUTPUT RISE/FALL TIME
FIGURE 18. PROPAGATION DELAY vs V
DD
FN7707 Rev 5.00
October 13, 2016
Page 9 of 16
ISL89163, ISL89164, ISL89165
ENx
INx
Functional Description
Overview
D
OUTx
The ISL89163, ISL89164, ISL89165 MOSFET drivers incorporate
several features optimized for Synchronous Rectifier (SR) driver
applications including precision input logic thresholds, enable
inputs, undervoltage lockout, and high amplitude output drive
currents.
R
del
cdel
FIGURE 19. DELAY USING RCD NETWORK
In Figure 19, R and C delay the rising edge of the input
del del
signal. For the falling edge of the input signal, the diode shorts
out the resistor resulting in a minimal falling edge delay.
The precision input thresholds facilitate the use of an external RC
network to delay the rising or falling propagation of the driver
output. This is a useful feature for adjusting when the SRs turn on
relative to the primary side FETs. In a similar manner, these
drivers can also be used to control the turn-on/off timing of the
primary side FETs.
The 37% and 63% thresholds of Options A and B were chosen to
simplify the calculations for the desired time delays. When using
an RC circuit to generate a time delay, the delay is simply
T (secs) = R (ohms) x C (farads). Please note that this equation
only applies if the input logic voltage is matched to the 3.3V or 5V
threshold options. If the logic high amplitude is not equal to 3.3V
or 5V, then the equations shown in Equation 1 can be used for
more precise delay calculations.
The Enable inputs (ENA, ENB) are used to emulate diode
operation of the SRs by disabling the driver output when it is
necessary to prevent negative currents in the output filter
inductors. An example is turning off the SRs when the power
supply output is turned off. This prevents the output capacitor
from being discharged through the output inductor. If this is
allowed to happen, the voltage across the output capacitor will
ring negative possibly damaging the capacitor (if it is polarized)
and probably damaging the load. Another example is preventing
circulating currents between paralleled power supplies during no
or light load conditions. During light load conditions (especially
when active load sharing is not active), energy will be transferred
from the paralleled power supply that has a higher voltage to the
paralleled power supply with the lower voltage. Consequently, the
energy that is absorbed by the low voltage output is then
transferred to the primary side causing the bus voltage to
increase until the primary side is damaged by excessive voltage.
High level of the logic signal into the RC
Positive going threshold for 5V logic (B option)
Low level of the logic signal into the RC
V
V
V
10V
H
63% 5V
thres
.3V
L
Timing values
R
100
1nF
del
C
t
del
V
V
thres
L
R
C
ln
1
del
del del
V
V
L
H
nominal delay time for this example
t
34.788 ns
del
(EQ. 1)
The start-up sequence for input threshold Options A, B, and C is
In this example, the high logic voltage is 10V, the positive
designed to prevent unexpected glitches when V is being
DD
threshold is 63% of 5V and the low level logic is 0.3V. Note the
rising edge propagation delay of the driver must be added to this
value.
turned on or turned off. When V < ~1V, an internal 10kΩ
DD
resistor connected between the output and ground, help to keep
the gate voltage close to ground. When ~1V < V < UV, both
DD
The minimum recommended value of C is 100pF. The parasitic
capacitance of the PCB and any attached scope probes will
introduce significant delay errors if smaller values are used.
Larger values of C will further minimize errors.
outputs are driven low while ignoring the logic inputs. This low
state has the same current sinking capacity as during normal
operation. This insures that the driven FETs are held off even if
there is a switching voltage on the drains that can inject charge
into the gates via the Miller capacitance. When V > UVLO, and
after a 400µs delay, the outputs now respond to the logic inputs.
See Figure 10 for complete details.
DD
Acceptable values of R are primarily effected by the source
resistance of the logic inputs. Generally, 100Ω resistors or larger
are usable.
For the negative transition of V through the UV lockout voltage,
DD
the outputs of input threshold Options A or B are active low when
Paralleling Outputs to Double the Peak Drive
Currents
V
< ~3.2V regardless of the input logic states. Similarly, the
DD
DC
C option outputs are active low when V < ~6.5V
.
DD
DC
The typical propagation matching of the ISL89163 and ISL89164
is less than 1ns. The matching is so precise that carefully
matched and calibrated scopes probes and scope channels must
be used to make this measurement. Because of this excellent
performance, these driver outputs can be safely paralleled to
double the current drive capacity. It is important that the INA and
INB inputs be connected together on the PCB with the shortest
possible trace. This is also required of OUTA and OUTB. Note that
the ISL89165 cannot be paralleled because of the
Application Information
Precision Thresholds for Time Delays
Three input logic voltage levels are supported by the ISL89163,
ISL89164, ISL89165. Option A is used for 3.3V logic, Option B is
used for 5.0V logic, and Option C is used for higher voltage logic
when it is desired to have voltage thresholds that are
proportional to V . The A and B options have nominal
complementary logic.
DD
thresholds that are 37% and 63% of 3.3V and 5.0V respectively
and the C option is 20% and 80% of V
.
DD
FN7707 Rev 5.00
October 13, 2016
Page 10 of 16
ISL89163, ISL89164, ISL89165
Equation 2 shows calculating the power dissipation of the driver:
Power Dissipation of the Driver
The power dissipation of the ISL89163, ISL89164, ISL89165 is
dominated by the losses associated with the gate charge of the
driven bridge FETs and the switching frequency. The internal bias
current also contributes to the total dissipation, but is usually not
significant as compared to the gate charge losses.
R
gate
--------------------------------------------
P
= 2 Q freq V
+ I freq V
DD
D
c
GS
DD
R
+ r
DSON
gate
(EQ. 2)
where:
freq = Switching frequency,
= V bias of the ISL89163, ISL89164, ISL89165
12
10
V
GS
DD
V
= 64V
Q = Gate charge for V
DS
c
GS
(freq) = Bias current at the switching frequency (see Figure 11)
DD
I
8
6
4
2
0
V
= 40V
DS
r
= ON-resistance of the driver
DS(ON)
R
= External gate resistance (if any).
gate
Note that the gate power dissipation is proportionally shared with
the external gate resistor. Do not overlook the power dissipated
by the external gate resistor.
Typical Application Circuits
0
2
4
6
8
10 12 14 16 18 20 22 24
GATE CHARGE (nC)
This drive circuit provides primary to secondary line isolation. A
controller, on the primary side, is the source of the SR control
signals OUTLLN and OUTLRN signals. The secondary side signals,
V1 and V2 are rectified by the dual diode, D9, to generate the
secondary side bias for U4. V1 and V3 are also inverted by Q100
Q
g,
FIGURE 20. MOSFET GATE CHARGE vs GATE VOLTAGE
Figure 20 illustrates how the gate charge varies with the gate
voltage in a typical power MOSFET. In this example, the total gate
and Q101 and the rising edges are delayed by R /C and
27 10
charge for V = 10V is 21.5nC when V = 40V. This is the
gs DS
R
/C respectively to generate the SR drive signals, LRN and
28
9
charge that a driver must source to turn-on the MOSFET and
must sink to turn-off the MOSFET.
LLN. For more complete information on this SR drive circuit, and
other applications for the ISL89163, ISL89164, ISL89165, refer
to AN1603 “ISL6752/54EVAL1Z ZVS DC/DC Power Supply with
Synchronous Rectifiers User Guide”.
PWM
/OUTLLN
/OUTLRN
L
R
L
PRIMARY TO SECONDARY SIDE
SELF BIASING, ISOLATED SR DRIVE
VBIAS
ENABLE
R27
D9
V2
OUTLLN
V1
LRN
Q100
C123
V1
U4
R28
V4
R-SR
LSR
V2
LLN
V3
EL7212
ISL89163
U4
OUTLRN
Q101
T6
V3
LLN
C9
C10
V4
RED DASHED LINES POINT OUT THE
TURN-ON DELAY OF THE SRS WHEN
PWM GOES LOW
LRN
FN7707 Rev 5.00
October 13, 2016
Page 11 of 16
ISL89163, ISL89164, ISL89165
General PCB Layout Guidelines
General EPAD Heatsinking
Considerations
The thermal pad is electrically connected to the GND supply
through the IC substrate. The EPAD of the ISL89163, ISL89164,
ISL89165 has two main functions: to provide a quiet GND for the
input threshold comparators and to provide heat sinking for the
IC. The EPAD must be connected to a ground plane and no
switching currents from the driven FET should pass through the
ground plane under the IC.
The AC performance of the ISL89163, ISL89164, ISL89165
depends significantly on the design of the PC board. The
following layout design guidelines are recommended to achieve
optimum performance:
• Place the driver as close as possible to the driven power FET.
• Understand where the switching power currents flow. The high
amplitude di/dt currents of the driven power FET will induce
significant voltage transients on the associated traces.
Figure 21 is a PCB layout example of how to use vias to remove
heat from the IC through the EPAD.
• Keep power loops as short as possible by paralleling the
source and return traces.
For maximum heatsinking, it is recommended that a ground
plane, connected to the EPAD, be added to both sides of the PCB.
A via array, within the area of the EPAD, will conduct heat from
the EPAD to the GND plane on the bottom layer. The number of
vias and the size of the GND planes required for adequate
heatsinking is determined by the power dissipated by the
ISL89163, ISL89164, ISL89165, the air flow and the maximum
temperature of the air around the IC.
• Use planes where practical; they are usually more effective
than parallel traces.
• Avoid paralleling high amplitude di/dt traces with low level
signal lines. High di/dt will induce currents and consequently,
noise voltages in the low level signal lines.
• When practical, minimize impedances in low level signal
circuits. The noise, magnetically induced on a 10kΩ resistor, is
10x larger than the noise on a 1kΩ resistor.
• Be aware of magnetic fields emanating from transformers and
inductors. Gaps in the magnetic cores of these structures are
especially bad for emitting flux.
EPAD GND
EPAD GND
PLANE
PLANE
• If you must have traces close to magnetic devices, align the
traces so that they are parallel to the flux lines to minimize
coupling.
• The use of low inductance components, such as chip resistors
and chip capacitors, is highly recommended.
BOTTOM
COMPONENT
LAYER
• Use decoupling capacitors to reduce the influence of parasitic
LAYER
inductance in the V and GND leads. To be effective, these
DD
caps must also have the shortest possible conduction paths. If
vias are used, connect several paralleled vias to reduce the
inductance of the vias.
FIGURE 21. TYPICAL PCB PATTERN FOR THERMAL VIAS
• It may be necessary to add resistance to dampen resonating
parasitic circuits especially on OUTA and OUTB. If an external
gate resistor is unacceptable, then the layout must be
improved to minimize lead inductance.
• Keep high dv/dt nodes away from low level circuits. Guard
banding can be used to shunt away dv/dt injected currents
from sensitive circuits. This is especially true for control circuits
that source the input signals to the ISL89163, ISL89164,
ISL89165.
• Avoid having a signal ground plane under a high amplitude
dv/dt circuit. This will inject di/dt currents into the signal
ground paths.
• Do power dissipation and voltage drop calculations of the
power traces. Many PCB/CAD programs have built in tools for
calculation of trace resistance.
• Large power components (Power FETs, Electrolytic caps, power
resistors, etc.) will have internal parasitic inductance which
cannot be eliminated.
This must be accounted for in the PCB layout and circuit design.
• If you simulate your circuits, consider including parasitic
components especially parasitic inductance.
FN7707 Rev 5.00
October 13, 2016
Page 12 of 16
ISL89163, ISL89164, ISL89165
Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted.
Please visit our website to make sure you have the latest revision.
DATE
REVISION
FN7707.5
CHANGE
Ton_delay parameter added to the AC Electrical Specifications.
The “up to 400µs” label of Figure 9 is changed to “400µs typical (Ton_delay)”.
October 13, 2016
Updated the Ordering Information table on page 3.
Replaced Products section with About Intersil section.
Updated Package Outline Drawing L8.3x3I to the latest revision. Changes are as follows:
-Tiebar Note updated
September 30, 2015 FN7707.4
From: Tiebar shown (if present) is a non-functional feature.
To: Tiebar shown (if present) is a non-functional feature and may be located on any of the 4 sides (or ends).
(page 5) ENA and ENB added to the Input Range parameter
(page 6) Propagation delay testing parameters changed for option C
(page 6) Note 13 added
(page 7) Figure 3 modified to show different input thresholds for testing prop delays for option C
February 22, 2012 FN7707.3 (page 4) The startup sequence references for the VDD Undervoltage Lock-out parameters for Option C is now the
same as Options A and B. Options A, B, and C now have the same startup sequence.
(page 5) Note 9 is rewritten to be more precise.
(page 8) The old startup sequence for Option C has been deleted (formerly Figure 10)
(page 10) The old startup sequence description in the Functional Description Overview has been deleted.
(page 1) vertical part numbers in the right margin are deleted to conform to new datasheet standards.
(page 1) Last paragraph of the product description is changed to better describe the improved turn on characteristics.
(page 1) features list is reduced in size to 8 features. Some features are reworded to improve readability.
(page 1) a reference to a non-existent application note is deleted from the Related Literature section.
(page 2) pin configuration pictures are redrawn and relabeled for readability.
(page 2) some pins description names are changed to corollate to the pin name in the pin configuration pictures.
Some descriptions are also corrected. The truth table associated with the pin descriptions is expanded to include the
logic performance of the under-voltage. (these revisions are not a change to function).
(page 4) note and figure references are added to the VDD Under-voltage lock-out parameter for options A, B, and C
(page 5) note 12 is revised to more clearly describe the turn-on characteristics of options A, B, and C.
(page 6) no load test conditions added to the rising and falling propagation matching parameters.
(page 8) figures 7 and 8 added to clearly define the startup characteristics
January 9, 2012
FN7707.2
(page 10) the last paragraph of the Functional Description overview is replaced by 3 paragraphs to more clearly
describe the under voltage and turn-on and turn-off characteristics.
(page 11). A new section is added to the application information describing how the drivers outputs can be paralleled.
(pages 1..13) various minor corrections to text for grammar and spelling.
(page 5) Note 12 revised from 200µs to 400µs
(page 4) The Operating Junction Temp Range in the “Thermal Information” was revised to read
August 26, 2011
October 12, 2010
FN7707.1 “Maximum Operating Junction Temp Range....-40°C to +150°C” from “-40°C to +125°C”
Updated POD M8.15D by converting to new POD format. Removed table of dimensions and moved dimensions onto
drawing. Added land pattern.
FN7707.0 Initial Release
FN7707 Rev 5.00
October 13, 2016
Page 13 of 16
ISL89163, ISL89164, ISL89165
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing, and high-end consumer markets.
For the most updated datasheet, application notes, related documentation, and related parts, see the respective product information
page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support.
© Copyright Intersil Americas LLC 2010-2016. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN7707 Rev 5.00
October 13, 2016
Page 14 of 16
ISL89163, ISL89164, ISL89165
For the most recent package outline drawing, see L8.3x3I.
Package Outline Drawing
L8.3x3I
8 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE
Rev 2 5/15
2X 1.950
3.00
A
6X 0.65
B
5
8
(4X)
0.15
1.64 +0.10/ - 0.15
6
PIN 1
INDEX AREA
6
PIN #1 INDEX AREA
4
1
4
8X 0.30
0.10 M C A B
8X 0.400 ± 0.10
TOP VIEW
2.38
+0.10/ - 0.15
BOTTOM VIEW
SEE DETAIL "X"
( 2.38 )
( 1.95)
0.10
C
C
Max 0.80
0.08
C
SIDE VIEW
( 8X 0.60)
(1.64)
( 2.80 )
PIN 1
5
0 . 2 REF
C
(6x 0.65)
0 . 00 MIN.
0 . 05 MAX.
( 8 X 0.30)
DETAIL "X"
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
4. Dimension applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5. Tiebar shown (if present) is a non-functional feature and may be
located on any of the 4 sides (or ends).
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
FN7707 Rev 5.00
October 13, 2016
Page 15 of 16
ISL89163, ISL89164, ISL89165
For the most recent package outline drawing, see M8.15D.
Package Outline Drawing
M8.15D
8 LEAD NARROW BODY SMALL OUTLINE EXPOSED PAD PLASTIC PACKAGE
Rev 1, 3/11
8
INDEX
AREA
6.20 (0.244)
5.84 (0.230)
DETAIL "A"
1.27 (0.050)
0.41 (0.016)
3.99 (0.157)
3.81 (0.150)
0.50 (0.02)
x 45°
1
2
3
0.25 (0.01)
TOP VIEW
8°
0°
0.25 (0.010)
0.19 (0.008)
SEATING PLANE
SIDE VIEW “B”
1.72 (0.067)
4.98 (0.196)
4.80 (0.189)
1.52 (0.059)
-C-
2.25
(0.089)
1.95
(0.077)
0.25 (0.010)
0.10 (0.004)
1.27 (0.050)
1
2
3
4
8
0.46 (0.019)
0.36 (0.014)
0.60 (0.023)
1.27 (0.050)
7
6
5
SIDE VIEW “A
1
2
3
5.45 (0.214)
2.50 (0.099)
2.00 (0.078)
TYPICAL RECOMMENDED LAND PATTERN
8
NOTES:
1. Dimensions are in millimeters. Dimensions in ( ) for reference only.
2. Dimensioning and tolerancing per ASME-Y14.5M-1994.
3. Unless otherwise specified, tolerance: Decimal ± 0.05.
3.50 (0.137)
3.00 (0.118)
4. Dimension does not include interlead flash or protrusions. Interlead flash
or protrusions shall not exceed 0.25mm per side.
5. The Pin 1 identifier may be either a mold or a mark feature.
6. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
BOTTOM VIEW
FN7707 Rev 5.00
October 13, 2016
Page 16 of 16
相关型号:
ISL89164FRTCZ-T
High Speed, Dual Channel, 6A, Power MOSFET Driver with Enable Inputs; DFN8, SOIC8; Temp Range: -40° to 125°C
RENESAS
ISL89165FBEAZ-T
High Speed, Dual Channel, 6A, Power MOSFET Driver with Enable Inputs; DFN8, SOIC8; Temp Range: -40° to 125°C
RENESAS
©2020 ICPDF网 联系我们和版权申明