ISL32485EIBZ-T13 [RENESAS]
LINE TRANSCEIVER;
| 型号： | ISL32485EIBZ-T13 |
| 厂家： | 
RENESAS TECHNOLOGY CORP |
| 描述： | LINE TRANSCEIVER 接口集成电路 |
| 文件： | 总17页 (文件大小：624K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DATASHEET
Fault Protected, Extended CMR, RS-485/RS-422
Transceivers with Cable Invert and ±16.5kV ESD
ISL32483E, ISL32485E
The ISL32483E and ISL32485E are fault protected, 5V powered
differential transceivers that exceed the RS-485 and RS-422
Features
• Fault protected RS-485 bus pins . . . . . . . . . . . . . . up to ±60V
standards for balanced communication. The RS-485 transceiver
pins (driver outputs and receiver inputs) are fault protected up to
±60V and are protected against ±16.5kV ESD strikes without
latch-up. Additionally, the extended common mode range allows
these transceivers to operate in environments with common
mode voltages up to ±25V (>2X the RS-485 requirement),
making this fault-protected RS-485 family one of the most robust
on the market.
• Extended common mode range. . . . . . . . . . . . . . . . . . . . ±25V
more than twice the range required for RS-485
• ±16.5kV HBM ESD protection on RS-485 bus pins
• Cable invert pins corrects for reversed cable connections
while maintaining Rx full fail-safe functionality
• Full fail-safe (open, short, terminated) RS-485 receivers
• 1/4 Unit Load (UL) for up to 128 devices on the bus
Transmitters (Tx) deliver an exceptional 2.5V (typical)
differential output voltage into the RS-485 specified 54Ω load.
This yields better noise immunity than standard RS-485 ICs or
allows up to six 120Ω terminations in star network topologies.
• High Rx I for opto-couplers in isolated designs
OL
• Hot plug circuitry: Tx and Rx outputs remain three-state
during power-up/power-down
Receiver (Rx) inputs feature a “full fail-safe” design, which
ensures a logic high Rx output if Rx inputs are floating,
shorted, or on a terminated but undriven (idle) bus.
• Slew rate limited RS-485 data rate . . . . . . . . . . . . . . . 1Mbps
• Low quiescent supply current. . . . . . . . . . . . . . . . . . . . 2.3mA
• Ultra low shutdown supply current. . . . . . . . . . . . . . . . . . 10µA
The ISL32483E and ISL32485E include cable invert functions
that reverse the polarity of the Rx and/or Tx bus pins in case
the cable is misconnected. Unlike competing devices, Rx full
fail-safe operation is maintained even when the Rx input
polarity is switched.
Applications
• Utility meters/automated meter reading systems
• High node count RS-485 systems
For fault protected RS-485 transceivers without the cable
invert function, please see the ISL32470E and ISL32490E
datasheets.
• PROFIBUS™ and RS-485 based field bus networks and
factory automation
• Security camera networks
• Building lighting and environmental control systems
• Industrial/process control networks
30
25
VID = ±1V
B
25
A
12
0
20
15
10
-7
-12
5
RO
0
-20
-25
-5
STANDARD RS-485
TRANSCEIVER
CLOSEST
COMPETITOR
ISL3248XE
TIME (400ns/DIV)
FIGURE 1. EXCEPTIONAL Rx OPERATES AT 1Mbps EVEN WITH
±25V COMMON MODE VOLTAGE
FIGURE 2. TRANSCEIVERS DELIVER SUPERIOR COMMON MODE
RANGE vs STANDARD RS-485 DEVICES
May 13, 2015
FN7785.3
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2011, 2012, 2014, 2015. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
1
All other trademarks mentioned are the property of their respective owners.
ISL32483E, ISL32485E
TABLE 1. SUMMARY OF FEATURES
POLARITY
LOW
HALF/FULL
DUPLEX
DATA RATE SLEW-RATE
EN
PINS?
HOT
PLUG
REVERSAL
PINS?
QUIESCENT I
(mA)
POWER
SHDN?
CC
PART NUMBER
ISL32483E
ISL32485E
(Mbps)
LIMITED?
PIN COUNT
Full
1
1
Yes
Yes
Yes
Yes
Yes
Yes
2.3
2.3
Yes
No
14
8
Half
Yes
Tx Only
Ordering Information
PART NUMBER
PART
MARKING
TEMP. RANGE
(°C)
PACKAGE
(RoHS Compliant)
PKG.
DWG. #
(Notes 1, 2, 3)
ISL32483EIBZ
ISL32485EIBZ
NOTES:
ISL32483 EIBZ
32485 EIBZ
-40 to +85
-40 to +85
14 Ld SOIC
8 Ld SOIC
M14.15
M8.15
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL32483E and ISL32485E. For more information on MSL please see
techbrief TB363.
Pin Configurations
ISL32483E
(14 LD SOIC)
TOP VIEW
ISL32485E
(8 LD SOIC)
TOP VIEW
RINV
RO
1
2
3
4
5
6
7
14 VCC
13 VCC
12 A
RO
INV
DE
DI
1
2
3
4
8
7
6
5
VCC
B/Z
R
R
D
A/Y
RE
D
GND
DE
11 B
DI
10 Z
GND
GND
9
8
Y
DINV
FN7785.3
May 13, 2015
Submit Document Feedback
2
ISL32483E, ISL32485E
Pin Descriptions
PIN
ISL32483E
ISL32485E
NAME
PIN #
PIN #
DESCRIPTION
RO
2
1
Receiver output. If INV or RINV is low, then: If A - B -10mV, RO is high; if A - B -200mV, RO is low. If INV or
RINV is high, then: If B - A -10mV, RO is high; if B - A -200mV, RO is low. In all cases, RO = High if A and B
are unconnected (floating) or shorted together or connected to an undriven, terminated bus (i.e., Rx is always
fail safe open, shorted and idle even if polarity is inverted).
RE
DE
DI
3
4
5
-
Receiver output enable. RO is enabled when RE is low; RO is high impedance when RE is high. Internally
pulled low.
3
4
Driver output enable. The driver outputs, Y and Z, are enabled by bringing DE high and they are high
impedance when DE is low. Internally pulled high to V
.
CC
Driver input. If INV or DINV is low, a low on DI forces output Y low and output Z high, while a high on DI forces
output Y high and output Z low. The output states relative to DI invert if INV or DINV is high.
GND
A/Y
6, 7
-
5
6
Ground connection.
±60V Fault and ±16.5kV HBM ESD Protected RS-485/RS-422 level I/O pin. If INV is low than, A/Y is the
noninverting receiver input and noninverting driver output. If INV is high, than A/Y is the inverting receiver
input and the inverting driver output. Pin is an input if DE = 0; pin is an output if DE = 1.
B/Z
-
7
±60V Fault and ±16.5kV HBM ESD Protected RS-485/RS-422 level I/O pin. If INV is low, than B/Z is the
inverting receiver input and inverting driver output. If INV is high, than B/Z is the noninverting receiver input
and the noninverting driver output. Pin is an input if DE = 0; pin is an output if DE = 1.
A
B
Y
Z
12
11
9
-
-
-
-
±60V Fault and ±15kV HBM ESD Protected RS-485/RS-422 level input. If RINV is low, then A is the
noninverting receiver input. If RINV is high, then A is the inverting receiver input.
±60V Fault and ±15kV HBM ESD Protected RS-485/RS-422 level input. If RINV is low, then B is the inverting
receiver input. If RINV is high, then B is the noninverting receiver input.
±60V Fault and ±15kV HBM ESD Protected RS-485/RS-422 level output. If DINV is low, then Y is the
noninverting driver output. If DINV is high, then Y is the inverting driver output
10
±60V Fault and ±15kV HBM ESD Protected RS-485/RS-422 level. If DINV is low, then Z is the inverting driver
output. If DINV is high, then Z is the noninverting driver output.
VCC
INV
13, 14
-
8
2
System power supply input (4.5V to 5.5V).
Receiver and driver polarity selection input. When driven high, this pin swaps the polarity of the driver output
and receiver input pins. If unconnected (floating) or connected low, normal RS-485 polarity conventions
apply. Internally pulled low.
RINV
DINV
1
8
-
-
Receiver polarity selection input. When driven high, this pin swaps the polarity of the receiver input pins. If
unconnected (floating) or connected low, normal RS-485 polarity conventions apply. Internally pulled low.
Driver polarity selection input. When driven high, this pin swaps the polarity of the driver output pins. If
unconnected (floating) or connected low, normal RS-485 polarity conventions apply. Internally pulled low.
FN7785.3
May 13, 2015
Submit Document Feedback
3
ISL32483E, ISL32485E
RECEIVING
INPUTS
DE
Truth Tables
OUTPUT
RO
TRANSMITTING
RE
DE
(Half Duplex) (Full Duplex)
A-B
INV or
RINV
INPUTS
OUTPUTS
RE
X
DE
1
DI
1
0
1
0
X
INV or DINV
Y
1
0
0
1
Z
0
0
0
0
0
0
0
0
0
0
X
X
X
X
X
-0.01V
-0.2V
0.01V
0.2V
0
0
1
1
X
1
0
1
0
1
0
0
1
1
X
X
0
1
X
1
X
1
1
X
1
0
Inputs
Open or
Shorted
0
0
High-Z
High-Z
High-Z
High-Z
1
0
X
(see Note) (see Note)
1
1
0
1
0
1
X
X
X
High-Z
(see Note)
NOTE: Low Power Shutdown Mode (see Note 11 on page 7), except for
ISL32485E.
X
High-Z
NOTE: Low Power Shutdown Mode (see Note 11 on page 7), except for
ISL32485E.
Typical Operating Circuits
+5V
+5V
+
0.1µF
+
0.1µF
13, 14
13, 14
1
V
V
RINV
RO
CC
CC
R
B
A
11
12
Y
Z
T
9
DI
2
5
R
D
10
3
4
RE
DE
DE 4
3
2
RE
RO
R
9
Y
Z
T
B
A
11
12
5
8
DI
R
10
D
1
8
RINV
DINV
DINV
GND
6, 7
GND
6, 7
THE IC ON THE LEFT HAS THE CABLE CONNECTIONS
SWAPPED, SO THE INV PINS (1, 8) ARE STRAPPED
HIGH TO INVERT ITS Rx AND Tx POLARITY
FIGURE 3. ISL32483E FULL DUPLEX EXAMPLE
FN7785.3
May 13, 2015
Submit Document Feedback
4
ISL32483E, ISL32485E
Absolute Maximum Ratings
Thermal Information
V
to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Thermal Resistance (Typical)
8 Ld SOIC Package (Notes 4, 5). . . . . . . . . .
14 Ld SOIC Package (Notes 4, 5) . . . . . . . .
(°C/W)
104
78
JC
(°C/W)
47
42
CC
JA
Input Voltages
DI, INV, RINV, DINV, DE, RE. . . . . . . . . . . . . . . . . . . . -0.3V to (V + 0.3V)
CC
Input/Output Voltages
A/Y, B/Z, A, B, Y, Z. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±60V
A/Y, B/Z, A, B, Y, Z (Transient Pulse Through 100Ω, see Note 15) ±80V
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . . -65°C to +150°C
Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .see TB493
RO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (V +0.3V)
CC
Short-circuit Duration
Recommended Operating Conditions
Y, Z. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite
ESD Rating . . . . . . . . . . . . . . . . . . . . see “ESD PERFORMANCE” on page 6
Latch-up (Tested per JESD78, Level 2, Class A). . . . . . . . . . . . . . . . +125°C
Supply Voltage (V ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V
CC
Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Bus Pin Common Mode Voltage Range . . . . . . . . . . . . . . . . . -25V to +25V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
JA
5. For , the “case temp” location is taken at the package top center.
JC
Electrical Specifications Test Conditions: V = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V = 5V, T = +25°C (Note 6).
CC
CC
A
Boldface limits apply across the operating temperature range, -40°C to +85°C.
TEMP
(°C)
MIN
(Note 14)
MAX
(Note 14)
PARAMETER
SYMBOL
TEST CONDITIONS
TYP
-
UNIT
V
DC CHARACTERISTICS
Driver Differential V
(No load)
V
V
Full
-
V
OUT
OD1
CC
-
Driver Differential V
R
R
R
R
= 100Ω (RS-422)
Full
Full
Full
Full
2.4
1.5
2.0
0.8
3.2
2.5
2.5
1.3
V
V
V
V
OUT
OD2
L
L
L
L
(Loaded, Figure 4A)
= 54Ω (RS-485)
V
CC
-
= 54Ω (PROFIBUS, V ≥ 5V)
CC
= 21Ω (Six 120Ω terminations for Star
-
Configurations, V ≥ 4.75V)
CC
Change in Magnitude of Driver
V
R
= 54Ω or 100Ω (Figure 4A)
Full
-
-
0.2
V
OD
L
Differential V
for
OUT
Complementary Output
States
Driver Differential V
OUT
Common Mode Load
(Figure 4B)
with
V
R
R
R
R
R
R
= 60Ω, -7V ≤ V ≤ 12V
CM
Full
Full
Full
Full
Full
Full
1.5
1.7
0.8
-1
2.1
V
V
V
V
V
V
V
OD3
L
L
L
L
L
L
CC
= 60Ω, -25V ≤ V ≤ 25V (V ≥ 4.75V)
CM CC
2.3
= 21Ω, -15V ≤ V ≤ 15V (V ≥ 4.75V)
CM CC
1.1
-
Driver Common Mode V
(Figure 4)
V
= 54Ω or 100Ω
-
-
-
3
5
OUT
OC
= 60Ω or 100Ω, -20V ≤ V ≤ 20V
-2.5
-
CM
Change in Magnitude of Driver
Common Mode V for
DV
= 54Ω or 100Ω (Figure 4A)
0.2
OC
OUT
Complementary Output
States
Driver Short-circuit Current
I
DE = V , -25V ≤ V ≤ 25V (Note 8)
CC
Full
Full
Full
Full
Full
Full
Full
-250
-83
-13
2.5
-
-
-
250
83
13
-
mA
mA
mA
V
OSD
O
I
I
At First fold-back, 22V ≤ V ≤ -22V
O
OSD1
OSD2
At Second fold-back, 35V ≤ V ≤ -35V
-
O
Logic Input High Voltage
Logic Input Low Voltage
Logic Input Current
V
DE, DI, RE, INV, RINV, DINV
DE, DI, RE, INV, RINV, DINV
DI
-
IH
V
-
0.8
1
V
IL
I
-1
-
µA
µA
IN1
DE, RE, INV, RINV, DINV
-15
6
15
FN7785.3
May 13, 2015
Submit Document Feedback
5
ISL32483E, ISL32485E
Electrical Specifications Test Conditions: V = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V = 5V, T = +25°C (Note 6).
CC
CC
A
Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued)
TEMP
(°C)
MIN
(Note 14)
MAX
(Note 14)
PARAMETER
SYMBOL
TEST CONDITIONS
TYP
110
-75
UNIT
µA
Input/Output Current (A/Y,
B/Z)
I
DE = 0V,
V
V
V
V
= 12V
= -7V
Full
Full
Full
Full
-
250
-
IN2
IN
IN
IN
IN
V
= 0V or 5.5V
= 0V or 5.5V
CC
CC
-200
-800
-6
µA
= ±25V
±240
±0.7
800
6
µA
= ±60V
mA
(Note 17)
Input Current (A, B)
(Full Duplex Versions Only)
I
V
V
V
V
V
= 12V
= -7V
Full
Full
Full
Full
-
90
-70
125
-
µA
µA
µA
mA
IN3
IN
IN
IN
IN
-100
-500
-3
= ±25V
= ±60V
±200
±0.5
500
3
(Note 17)
Output Leakage Current (Y, Z)
(Full Duplex Versions Only)
I
RE = 0V, DE = 0V,
= 0V or 5.5V
V
V
V
V
= 12V
= -7V
Full
Full
Full
Full
-
20
-5
200
-
µA
µA
µA
mA
OZD
IN
IN
IN
IN
V
CC
-100
-500
-3
= ±25V
= ±60V
±40
±0.15
500
3
(Note 17)
A-B if INV or RINV = 0; B-A if INV or RINV = 1,
-25V ≤ V ≤ 25V
Receiver Differential
Threshold Voltage
V
Full
-200
-100
-10
mV
TH
CM
Receiver Input Hysteresis
DV
-25V ≤ V ≤ 25V
25
-
25
4.75
4.2
-
mV
V
TH
CM
= -10mV
Receiver Output High Voltage
V
V
I
I
= -2mA
= -8mA
Full
Full
Full
Full
Full
V
- 0.5
-
-
OH
ID
O
CC
2.8
V
O
Receiver Output Low Voltage
Receiver Output Low Current
V
I
= 6mA, V = -200mV
O ID
-
0.27
22
0.4
-
V
OL
I
V
= 1V, V = -200mV
15
-1
mA
µA
OL
O ID
Three-state (High Impedance)
Receiver Output Current
I
I
0V ≤ V ≤ V (Note 16)
0.01
1
OZR
O
CC
Receiver Short-circuit Current
SUPPLY CURRENT
0V ≤ V ≤ V
Full
±12
-
±110
mA
OSR
O
CC
No-load Supply Current
(Note 7)
I
DE = V , RE = 0V or V , DI = 0V or V
CC CC CC
Full
Full
-
-
2.3
10
4.5
50
mA
µA
CC
Shutdown Supply Current
ESD PERFORMANCE
I
DE = 0V, RE = V , DI = 0V or V (Note 16)
CC CC
SHDN
RS-485 Pins (A, Y, B, Z, A/Y,
B/Z)
Human Body Model, 1/2 Duplex
25
25
-
-
±16.5
±15
-
-
kV
kV
From Bus Pins to
Full Duplex
GND
All Pins
Human Body Model, per JEDEC
Machine Model
25
25
-
-
±8
-
-
kV
V
±700
DRIVER SWITCHING CHARACTERISTICS
Driver Differential Output
Delay
t
t
R
= 54Ω, C = 50pF No CM load
Full
Full
Full
Full
-
-
-
-
70
125
350
15
ns
ns
ns
ns
PLH, PHL
D
D
(Figure 5)
-25V ≤ V ≤ 25V
CM
-
4.5
-
Driver Differential Output
Skew
t
R = 54Ω, C = 50pF No CM Load
D D
(Figure 5)
SKEW
-25V ≤ V ≤ 25V
25
CM
(Note 18)
Driver Differential Rise or Fall
Time
t , t
R
= 54Ω, C = 50pF No CM Load
Full
Full
Full
Full
Full
70
70
1
170
300
550
-
ns
ns
R
F
D
D
(Figure 5)
-25V ≤ V ≤ 25V
CM
-
4
-
Maximum Data Rate
f
C
= 820pF (Figure 7)
Mbps
ns
MAX
D
Driver Enable to Output High
Driver Enable to Output Low
t
SW = GND (Figure 6), (Note 9)
SW = V (Figure 6), (Note 9)
-
350
300
ZH
t
-
-
ns
ZL
CC
FN7785.3
May 13, 2015
Submit Document Feedback
6
ISL32483E, ISL32485E
Electrical Specifications Test Conditions: V = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V = 5V, T = +25°C (Note 6).
CC
CC
A
Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued)
TEMP
(°C)
MIN
(Note 14)
MAX
(Note 14)
PARAMETER
SYMBOL
TEST CONDITIONS
TYP
-
UNIT
ns
Driver Disable from Output
Low
t
SW = V (Figure 6)
Full
-
120
LZ
CC
Driver Disable from Output
High
t
SW = GND (Figure 6)
Full
-
-
120
ns
HZ
Time to Shutdown
t
(Notes 11, 16)
Full
Full
60
-
160
-
600
ns
ns
SHDN
Driver Enable from Shutdown
to Output High
t
SW = GND (Figure 6),
(Notes 11, 12, 16)
2000
ZH(SHDN)
Driver Enable from Shutdown
to Output Low
t
SW = V (Figure 6),
CC
(Notes 11, 12, 16)
Full
-
-
2000
ns
ZL(SHDN)
RECEIVER SWITCHING CHARACTERISTICS
Maximum Data Rate
f
-25V ≤ V ≤ 25V (Figure 8)
CM
Full
Full
Full
Full
1
-
15
90
4
-
Mbps
ns
MAX
, t
Receiver Input to Output Delay
t
-25V ≤ V ≤ 25V (Figure 8)
150
10
50
PLH PHL
CM
Receiver Skew | t
- t
|
t
(Figure 8)
-
ns
PLH PHL
SKD
Receiver Enable to Output
Low
t
R
= 1kΩ, C = 15pF, SW = V (Figure 9),
CC
-
-
ns
ZL
L
L
(Notes 10, 16)
Receiver Enable to Output
High
t
R
= 1kΩ, C = 15pF, SW = GND (Figure 9),
Full
Full
Full
-
-
-
-
-
-
50
50
50
ns
ns
ns
ZH
L
L
(Notes 10, 16)
R = 1kΩ, C = 15pF, SW = V (Figure 9)
L
(Note 16)
R = 1kΩ, C = 15pF, SW = GND (Figure 9)
L
Receiver Disable from Output
Low
t
LZ
L
CC
Receiver Disable from Output
High
t
HZ
L
(Note 16)
Time to Shutdown
t
(Notes 11, 16)
Full
Full
60
-
160
-
600
ns
ns
SHDN
Receiver Enable from
t
R
= 1kΩ, C = 15pF, SW = GND (Figure 9),
2000
ZH(SHDN)
L
L
Shutdown to Output High
(Notes 11, 13, 16)
Receiver Enable from
t
R
= 1kΩ, C = 15pF, SW = V (Figure 9),
Full
-
-
2000
ns
ZL(SHDN)
L
L
CC
Shutdown to Output Low
(Notes 11, 13, 16)
NOTES:
6. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise
specified.
7. Supply current specification is valid for loaded drivers when DE = 0V.
8. Applies to peak current. See “Typical Performance Curves” beginning on page 13 for more information.
9. Keep RE = 0 to prevent the device from entering SHDN.
10. The RE signal high time must be short enough (typically <100ns) to prevent the device from entering SHDN.
11. Transceivers (except on the ISL32485E) are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 60ns, the
parts are guaranteed not to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See
“Low Power Shutdown Mode” on page 12,
12. Keep RE = VCC and set the DE signal low time >600ns to ensure that the device enters SHDN.
13. Set the RE signal high time >600ns to ensure that the device enters SHDN.
14. Compliance to data sheet limits is assured by one or more methods: production test, characterization and/or design.
15. Tested according to TIA/EIA-485-A, Section 4.2.6 (±80V for 15ms at a 1% duty cycle).
16. Does not apply to the ISL32485E. The ISL32485E has no Rx enable function and thus no SHDN function.
17. See “Caution” statement in the “Recommended Operating Conditions” on page 5.
18. This parameter is not production tested.
FN7785.3
May 13, 2015
Submit Document Feedback
7
ISL32483E, ISL32485E
Test Circuits and Waveforms
R /2
L
R /2
375Ω
375Ω
DE
DI
L
V
DE
DI
CC
V
CC
Z
Y
Z
Y
V
CM
V
D
OD
V
D
OD
V
OC
V
R /2
L
OC
R /2
L
FIGURE 4A. V AND V
OD
FIGURE 4B. V AND V WITH COMMON MODE LOAD
OD OC
OC
FIGURE 4. DC DRIVER TEST CIRCUITS
3V
0V
DI
50%
50%
375Ω*
DE
DI
t
t
PHL
PLH
V
CC
V
OH
OUT (Z)
Z
R
C
D
D
D
V
V
OUT (Y)
CM
Y
OL
375Ω*
SIGNAL
GENERATOR
+V
-V
OD
*ONLY USED FOR COMMON
MODE LOAD TESTS
90%
10%
90%
10%
DIFF OUT (Y - Z)
OD
t
t
R
F
SKEW = |t
- t |
PLH PHL
FIGURE 5A. TEST CIRCUIT
FIGURE 5B. MEASUREMENT POINTS
FIGURE 5. DRIVER PROPAGATION DELAY AND DIFFERENTIAL TRANSITION TIMES
DE
DI
Z
Y
110Ω
V
CC
D
3V
GND
SW
SIGNAL
GENERATOR
DE
50%
50%
(Note 11
C
L
0V
t
, t
ZH ZH(SHDN)
(Note 11)
t
HZ
OUTPUT HIGH
V
OH
V
- 0.5V
OH
PARAMETER
OUTPUT
Y/Z
RE
DI
SW C (pF)
L
OUT (Y, Z)
2.3V
0V
t
X
1/0
0/1
1/0
0/1
1/0
0/1
GND
50
50
HZ
t
Y/Z
X
V
t
, t
ZL ZL(SHDN)
(Note 11
t
LZ
LZ
CC
V
CC
t
Y/Z
0 (Note 9)
0 (Note 9)
GND
100
100
100
100
ZH
OUT (Y, Z)
2.3V
OUTPUT LOW
t
Y/Z
V
ZL
CC
V
+ 0.5V
OL
V
OL
t
Y/Z
1 (Note 12)
1 (Note 12)
GND
ZH(SHDN)
t
Y/Z
V
CC
ZL(SHDN)
FIGURE 6A. TEST CIRCUIT
FIGURE 6B. MEASUREMENT POINTS
FIGURE 6. DRIVER ENABLE AND DISABLE TIMES
FN7785.3
May 13, 2015
Submit Document Feedback
8
ISL32483E, ISL32485E
Test Circuits and Waveforms(Continued)
DE
DI
3V
0V
V
CC
+
DI
Z
Y
54Ω
C
V
D
D
OD
-
SIGNAL
GENERATOR
+V
OD
DIFF OUT (Y - Z)
0V
-V
OD
FIGURE 7A. TEST CIRCUIT
FIGURE 7B. MEASUREMENT POINTS
FIGURE 7. DRIVER DATA RATE
RE
B
A
V
V
+ 750mV
- 750mV
CM
15pF
B
V
V
CM
CM
RO
R
A
CM
t
t
PHL
PLH
SIGNAL
GENERATOR
SIGNAL
GENERATOR
V
CC
50%
50%
RO
V
CM
0V
FIGURE 8A. TEST CIRCUIT
FIGURE 8B. MEASUREMENT POINTS
FIGURE 8. RECEIVER PROPAGATION DELAY AND DATA RATE
RE
B
A
1kΩ
V
RE
CC
RO
3V
0V
R
(Note 11)
GND
SW
SIGNAL
GENERATOR
50%
50%
15pF
t
t
, t
ZH ZH(SHDN)
t
HZ
OUTPUT HIGH
(Note 11)
V
PARAMETER
DE
0
A
SW
GND
OH
V
- 0.5V
OH
1.5V
RO
t
+1.5V
-1.5V
+1.5V
-1.5V
+1.5V
-1.5V
HZ
0V
t
0
V
LZ
CC
, t
ZL ZL(SHDN)
t
LZ
t
(Note 10)
(Note 10)
0
GND
ZH
(Note 11)
V
CC
t
0
V
ZL
CC
RO
1.5V
OUTPUT LOW
V
+ 0.5V
V
OL
OL
t
(Note 13)
0
GND
ZH(SHDN)
t
(Note 13)
0
V
CC
ZL(SHDN)
FIGURE 9A. TEST CIRCUIT
FIGURE 9B. MEASUREMENT POINTS
FIGURE 9. RECEIVER ENABLE AND DISABLE TIMES
FN7785.3
May 13, 2015
Submit Document Feedback
9
ISL32483E, ISL32485E
Driver (Tx) Features
Application Information
The RS-485/RS-422 driver is a differential output device that
delivers at least 1.5V across a 54Ω load (RS-485) and at least
2.4V across a 100Ω load (RS-422). The drivers feature low
propagation delay skew to maximize bit width and to minimize
EMI. Thus, all drivers are three-statable via the active high DE
input.
RS-485 and RS-422 are differential (balanced) data
transmission standards used for long haul or noisy environments.
RS-422 is a subset of RS-485, so RS-485 transceivers are also
RS-422 compliant. RS-422 is a point-to-multipoint (multidrop)
standard, which allows only one driver and up to 10 (assuming
one-unit load devices) receivers on each bus. RS-485 is a true
multipoint standard, which allows up to 32 one-unit load devices
(any combination of drivers and receivers) on each bus. To allow
for multipoint operation, the RS-485 specification requires that
drivers must handle bus contention without sustaining any
damage.
The driver outputs are slew rate limited to minimize EMI and to
minimize reflections in unterminated or improperly terminated
networks.
High Overvoltage (Fault) Protection
Increases Ruggedness
Another important advantage of RS-485 is the extended
Common Mode Range (CMR), which specifies that the driver
outputs and receiver inputs withstand signals that range from
+12V to -7V. RS-422 and RS-485 are intended for runs as long as
4000 feet, so the wide CMR is necessary to handle ground
potential differences, as well as voltages induced in the cable by
external fields.
The ±60V (referenced to the IC GND) fault protection on the
RS-485 pins makes these transceivers some of the most rugged
on the market. This level of protection makes the ISL3248xE
perfect for applications where power (e.g., 24V and 48V supplies)
must be routed in the conduit with the data lines or for outdoor
applications where large transients are likely to occur. When
power is routed with the data lines, even a momentary short
between the supply and data lines will destroy an unprotected
device. The ±60V fault levels of this family are at least 5x higher
than the levels specified for standard RS-485 ICs. The ISL3248xE
protection is active whether the Tx is enabled or disabled and
even if the IC is powered down.
The ISL3248xE is a family of ruggedized RS-485 transceivers
that improves on the RS-485 basic requirements and therefore
increases system reliability. The CMR increases to ±25V, while
the RS-485 bus pins (receiver inputs and driver outputs) include
fault protection against voltages and transients up to ±60V.
Additionally, larger-than-required differential output voltages
If transients or voltages (including overshoots and ringing)
greater than ±60V are possible, then additional external
protection is required.
(V ) increase noise immunity, while the ±16.5kV built-in ESD
OD
protection complements the fault protection.
Receiver (Rx) Features
Widest Common Mode Voltage (CMV)
Tolerance Improves Operating Range
These devices utilize a differential input receiver for maximum
noise immunity and common mode rejection. Input sensitivity is
better than ±200mV, as required by the RS-422 and RS-485
specifications.
The RS-485 networks operating in industrial complexes or over long
distances are susceptible to large CMV variations. Either of these
operating environments may suffer from large node-to-node ground
potential differences or CMV pickup from external electromagnetic
sources and devices with only the minimum required +12V to -7V
CMR may malfunction. The ISL3248xE’s extended ±25V CMR is the
widest available, allowing operation in environments that would
overwhelm lesser transceivers. Additionally, the Rx will not phase
invert (erroneously change state), even with CMVs of ±40V or
differential voltages as large as 40V.
Receiver input (load) current surpasses the RS-422 specification
of 3mA and is four times lower than the RS-485 “Unit Load (UL)”
requirement of 1mA maximum. Thus, these products are known
as “one-quarter UL” transceivers and there can be up to 128 of
these devices on a network while still complying with the RS-485
loading specification.
The Rx functions with common mode voltages as great as ±25V,
making them ideal for industrial or long networks where induced
voltages are a realistic concern.
Cable Invert (Polarity Reversal) Function
With large node count RS-485 networks, it is common for some
cable data lines to be wired backwards during installation. When
this happens, the node is unable to communicate over the
network. Once a technician finds the miswired node, the
connector must be rewired, which is time consuming.
All the receivers include a “full fail-safe” function that guarantees
a high-level receiver output if the receiver inputs are unconnected
(floating), shorted together or connected to a terminated bus with
all the transmitters disabled (i.e., an idle bus).
Rx outputs feature high drive levels (typically 22mA at V = 1V) to
OL
The ISL32483E and ISL32485E simplify this task by including
cable invert pins (INV, DINV, RINV) that allow the technician to
invert the polarity of the Rx input and/or the Tx output pins
simply by moving a jumper to change the state of the invert pins.
When the invert pin is low, the IC operates like any standard
RS-485 transceiver and the bus pins have their normal polarity
definition of A and Y being noninverting and B and Z being
inverting. With the invert pin high, the corresponding bus pins
reverse their polarity, so B and Z are now noninverting and A and
Y become inverting.
ease the design of optically coupled isolated interfaces. Except for
the ISL32485E, Rx outputs are three-statable via the active low RE
input.
The Rx includes noise filtering circuitry to reject high frequency
signals and typically rejects pulses narrower than 50ns
(equivalent to 20Mbps).
FN7785.3
May 13, 2015
Submit Document Feedback
10
ISL32483E, ISL32485E
Intersil’s unique cable invert function is superior to that found on
DE, DI = V
RE = GND
CC
competing devices because the Rx full fail-safe function is
maintained, even when the Rx polarity is reversed. Competitor
devices implement the Rx invert function simply by inverting the
Rx output. This means that with the Rx inputs floating or shorted
together, the Rx appropriately delivers a logic 1 in normal
polarity, but outputs a logic low when the IC is operated in the
inverted mode. Intersil’s innovative Rx design guarantees that,
5.0
2.5
3.5V
2.8V
V
CC
0
5.0
2.5
0
RL = 1kΩ
RL = 1kΩ
A/Y
ISL83088E
ISL3248XE
with the Rx inputs floating or shorted together (V = 0V), the Rx
ID
output remains high, regardless of the state of the invert pins.
5.0
2.5
The full duplex ISL32483E includes two invert pins that allow for
separate control of the Rx and Tx polarities. If only the Rx cable is
miswired, then only the RINV pin need be driven to a logic 1. If
the Tx cable is miswired, then DINV must be connected to a logic
high. The half-duplex version has only one logic pin (INV) that,
when high, switches the polarity of both the Tx and the Rx blocks.
RO
ISL3248XE
0
TIME (40µs/DIV)
FIGURE 10. HOT PLUG PERFORMANCE (ISL3248XE) vs ISL83088E
WITHOUT HOT PLUG CIRCUITRY
High V Improves Noise Immunity and
OD
Flexibility
ESD Protection
All pins on the ISL3248xE devices include Class 3 (>8kV) Human
Body Model (HBM) ESD protection structures that are good enough
to survive ESD events commonly seen during manufacturing. Even
so, the RS-485 pins (driver outputs and receiver inputs)
incorporate more advanced structures that allow them to survive
ESD events in excess of ±16.5kV HBM (±15kV for full-duplex
version). The RS-485 pins are particularly vulnerable to ESD
strikes, because they typically connect to an exposed port on the
exterior of the finished product. Simply touching the port pins or
connecting a cable can cause an ESD event that might destroy
unprotected ICs. The new ESD structures protect the device
whether or not it is powered up and without interfering with the
exceptional ±25V CMR. This built-in ESD protection minimizes the
need for board-level protection structures (e.g., transient
suppression diodes) and the associated, undesirable capacitive
load they present.
The ISL3248xE driver design delivers larger differential output
voltages (V ) than the RS-485 standard requirements or than
OD
most RS-485 transmitters can deliver. The typical ±2.5V V
OD
provides more noise immunity than networks built using many
other transceivers.
Another advantage of the large V is the ability to drive more
OD
than two bus terminations, which allows for utilizing the
ISL3248xE in “star” and other multi-terminated, nonstandard
network topologies.
Figure 11 on page 13 details the transmitter’s V versus I
OD
OUT
characteristic and includes load lines for four (30Ω) and six (20Ω)
120Ω terminations. Figure 11 shows that the driver typically
delivers ±1.3V into six terminations and the “Electrical
Specifications” on page 5 guarantees a V of ±0.8V at 21Ω over
OD
the full temperature range. The RS-485 standard requires a
Data Rate, Cables and Terminations
minimum 1.5V V into two terminations, but the ISL3248xE
OD
delivers RS-485 voltage levels with 2x to 3x the number of
terminations.
The RS-485/RS-422 are intended for network lengths up to 4000
feet, but the maximum system data rate decreases as the
transmission length increases. These 1Mbps versions can
operate at full data rates with lengths up to 800 ft. (244m). Jitter
is the limiting parameter at this data rate, so employing encoded
data streams (e.g., Manchester coded or Return-to-Zero) may
allow increased transmission distances.
Hot Plug Function
When a piece of equipment powers up, there is a period of time
in which the processor or ASIC driving the RS-485 control lines
(DE, RE) is unable to ensure that the RS-485 Tx and Rx outputs
are kept disabled. If the equipment is connected to a bus, a
driver activating prematurely during power-up may crash the bus.
To avoid this scenario, the ISL3248xE devices incorporate a “Hot
Twisted pair is the cable of choice for RS-485/RS-422
networks. Twisted pair cables tend to pick up noise and other
electromagnetically induced voltages as common mode
signals, which are effectively rejected by the differential
receivers in these ICs.
Plug” function. Circuitry monitoring V ensures that, during
CC
power-up and power-down, the Tx and Rx outputs remain
disabled, regardless of the state of DE and RE, if V is less than
CC
Proper termination is imperative to minimize reflections and
terminations are recommended unless power dissipation is an
overriding concern. In point-to-point, or point-to-multipoint (single
driver on bus like RS-422) networks, the main cable should be
terminated in its characteristic impedance (typically 120Ω) at the
end farthest from the driver. In multireceiver applications, stubs
connecting receivers to the main cable should be kept as short as
possible. Multipoint (multidriver) systems require that the main
cable be terminated in its characteristic impedance at both ends.
Stubs connecting a transceiver to the main cable should be kept as
short as possible.
≈3.5V. This gives the processor or ASIC a chance to stabilize and
drive the RS-485 control lines to the proper states. Figure 10
illustrates the power-up and power-down performance of the
ISL3248xE compared to an RS-485 IC without the Hot Plug
feature.
FN7785.3
May 13, 2015
Submit Document Feedback
11
ISL32483E, ISL32485E
Built-in Driver Overload Protection
Low Power Shutdown Mode
As stated previously, the RS-485 specification requires that
drivers survive worst-case bus contentions undamaged. These
transceivers meet this requirement via driver output short-circuit
current limits and on-chip thermal shutdown circuitry.
These BiCMOS transceivers all use a fraction of the power
required by competitive devices, but they also include a
shutdown feature (except the ISL32485E) that reduces the
already low quiescent I to a 10µA trickle. These devices enter
CC
shutdown whenever the receiver and driver are simultaneously
The driver output stages incorporate a double foldback,
short-circuit current limiting scheme, which ensures that the
output current never exceeds the RS-485 specification, even at
the common mode and fault condition voltage range extremes.
The first foldback current level (≈70mA) is set to ensure that the
driver never folds back when driving loads with common mode
voltages up to ±25V. The very low second foldback current
setting (≈9mA) minimizes power dissipation if the Tx is enabled
when a fault occurs.
disabled (RE = V and DE = GND) for a period of at least 600ns.
CC
Disabling both the driver and the receiver for less than 60ns
guarantees that the transceiver will not enter shutdown.
Note that receiver and driver enable times increase when the
transceiver enables from shutdown. Refer to Notes 9, 10, 11, 12
and 13, at the end of “Electrical Specifications” on page 5, for
more information.
In the event of a major short-circuit condition, devices also include
a thermal shutdown feature that disables the drivers whenever the
die temperature becomes excessive. This eliminates the power
dissipation, allowing the die to cool. The drivers automatically
re-enable after the die temperature drops about 15°C. If the
contention persists, the thermal shutdown/reenable cycle repeats
until the fault is cleared. Receivers stay operational during thermal
shutdown.
FN7785.3
May 13, 2015
Submit Document Feedback
12
ISL32483E, ISL32485E
Typical Performance Curves
V
= 5V, T = +25°C; Unless Otherwise Specified.
A
CC
3.6
3.4
3.2
3.0
2.8
2.6
2.4
2.2
90
80
70
60
50
40
30
20
10
0
R
= 20Ω
D
R
= 30Ω
D
+25°C
+85°C
R
= 100Ω
D
R
= 54Ω
D
R
= 100Ω
D
R
= 54Ω
D
0
1
2
3
4
5
-40
-25
0
25
50
75 85
DIFFERENTIAL OUTPUT VOLTAGE (V)
TEMPERATURE (°C)
FIGURE 11. DRIVER OUTPUT CURRENT vs DIFFERENTIAL OUTPUT
VOLTAGE
FIGURE 12. DRIVER DIFFERENTIAL OUTPUT VOLTAGE vs
TEMPERATURE
70
60
2.45
2.40
V
, +25°C
OL
DE = V , RE = X
CC
V
, +85°C
OL
50
40
30
20
10
0
2.35
2.30
2.25
2.20
2.15
2.10
2.05
2.00
DE = GND, RE = GND
-10
-20
-30
V
, +85°C
1
OH
V
, +25°C
3
OH
-40
-25
0
25
50
75 85
0
2
4
5
TEMPERATURE (°C)
RECEIVER OUTPUT VOLTAGE (V)
FIGURE 14. RECEIVER OUTPUT CURRENT vs RECEIVER OUTPUT
VOLTAGE
FIGURE 13. SUPPLY CURRENT vs TEMPERATURE
1000
150
+85°C
V
= 0V TO 5.5V
CC
800
600
400
200
0
100
50
Y OR Z = LOW
+25°C
0
Y or Z
-50
-100
-150
-200
-400
-600
Y OR Z = HIGH
+25°C
A/Y or B/Z
+85°C
-60 -50 -40 -30 -20 -10
0
10 20 30 40 50 60
-70 -60 -50 -40 -30 -20 -10
0
10 20 30 40 50 60 70
OUTPUT VOLTAGE (V)
BUS PIN VOLTAGE (V)
FIGURE 15. DRIVER OUTPUT CURRENT vs SHORT-CIRCUIT VOLTAGE
FIGURE 16. BUS PIN CURRENT vs BUS PIN VOLTAGE
FN7785.3
May 13, 2015
Submit Document Feedback
13
ISL32483E, ISL32485E
Typical Performance Curves
V
= 5V, T = +25°C; Unless Otherwise Specified. (Continued)
A
CC
4.0
3.5
3.0
2.5
2.0
85
80
75
70
65
60
55
50
R
= 54Ω, C = 50pF
D
R
= 54Ω, C = 50pF
D
D
D
t
PLH
t
PHL
|t
- t
|
PLH PHL
-40
-25
0
25
50
75 85
-40
-25
0
25
50
75 85
TEMPERATURE (°C)
TEMPERATURE (°C)
FIGURE 18. DRIVER DIFFERENTIAL SKEW vs TEMPERATURE
FIGURE 17. DRIVER DIFFERENTIAL PROPAGATION DELAY vs
TEMPERATURE
A
R
= 54Ω, C = 50pF
D
25
D
B
5
0
VID = ±1V
20
15
10
5
DI
5
0
RO
RO
RO
0
5
0
3
2
1
-5
-10
-15
-20
-25
0
-1
-2
-3
A
B
A/Y - B/Z
TIME (400ns/DIV)
TIME (400ns/DIV)
FIGURE 19. RECEIVER PERFORMANCE WITH ±25V CMV
FIGURE 20. DRIVER AND RECEIVER WAVEFORMS
Die Characteristics
SUBSTRATE POTENTIAL (POWERED UP):
GND
PROCESS:
Si Gate BiCMOS
FN7785.3
May 13, 2015
Submit Document Feedback
14
ISL32483E, ISL32485E
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you
have the latest Rev.
DATE
REVISION
FN7785.3
CHANGE
May 13, 2015
-Figure 3 on page 4: Changed the title from "ISL34183E" to "ISL32483E.
-“Thermal Information” on page 5 changes are:
* 14 Ld SOIC Package: Changed Theta-ja: From 88 to 78 and Theta-jc from 39 to 42.
*8 Ld SOIC Package: Changed Theta-ja: From 108 to 104.
- Changed "MAX" on “Driver Differential Rise or Fall Time” on page 6 from 400 to 550.
October 28, 2014
FN7785.2
On p6, in the "Driver Switching Characteristics" section, "Driver Differential Output Skew" parameter, in the
second "Test Conditions" line, added "(Note 18)" after the -25V ≤ Vcm ≤ 25V" entry. And on p7, added a new
Note 18 to the notes section saying, "This parameter is not production tested."
Updated POD M8.15 to most recent version with following changes:
Changed in Typical Recommended Land Pattern the following:
2.41(0.095) to 2.20(0.087)
0.76 (0.030) to 0.60(0.023)
0.200 to 5.20(0.205)
Changed Note 1 "1982" to "1994"
March 8, 2012
FN7785.1
FN7785.0
Page 5 - Thermal Resistance - 8 Ld SOIC package Theta JA changed from 116 to 108
Page 13 - Updated Figure 16 to show Pos breakdown between 60V and 70V.
January 18, 2011
Initial Release
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN7785.3
May 13, 2015
Submit Document Feedback
15
ISL32483E, ISL32485E
Package Outline Drawing
M14.15
14 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 1, 10/09
4
0.10 C A-B 2X
8.65
A
3
6
DETAIL"A"
0.22±0.03
D
14
8
6.0
3.9
4
0.10 C D 2X
0.20 C 2X
7
PIN NO.1
ID MARK
(0.35) x 45°
4° ± 4°
5
0.31-0.51
0.25M C A-B D
B
3
6
TOP VIEW
0.10 C
H
1.75 MAX
1.25 MIN
0.25
GAUGE PLANE
SEATING PLANE
C
0.10-0.25
1.27
0.10 C
SIDE VIEW
DETAIL "A"
(1.27)
(0.6)
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSEY14.5m-1994.
3. Datums A and B to be determined at Datum H.
(5.40)
4. Dimension does not include interlead flash or protrusions.
Interlead flash or protrusions shall not exceed 0.25mm per side.
5. The pin #1 indentifier may be either a mold or mark feature.
6. Does not include dambar protrusion. Allowable dambar protrusion
shall be 0.10mm total in excess of lead width at maximum condition.
(1.50)
7. Reference to JEDEC MS-012-AB.
TYPICAL RECOMMENDED LAND PATTERN
FN7785.3
May 13, 2015
Submit Document Feedback
16
ISL32483E, ISL32485E
Package Outline Drawing
M8.15
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 4, 1/12
DETAIL "A"
1.27 (0.050)
0.40 (0.016)
INDEX
AREA
6.20 (0.244)
5.80 (0.228)
0.50 (0.20)
x 45°
0.25 (0.01)
4.00 (0.157)
3.80 (0.150)
8°
0°
1
2
3
0.25 (0.010)
0.19 (0.008)
SIDE VIEW “B”
TOP VIEW
2.20 (0.087)
1
8
SEATING PLANE
0.60 (0.023)
1.27 (0.050)
1.75 (0.069)
5.00 (0.197)
4.80 (0.189)
2
3
7
6
1.35 (0.053)
-C-
4
5
0.25(0.010)
0.10(0.004)
1.27 (0.050)
0.51(0.020)
0.33(0.013)
5.20(0.205)
SIDE VIEW “A
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1. Dimensioning and tolerancing per ANSI Y14.5M-1994.
2. Package length does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
3. Package width does not include interlead flash or protrusions. Interlead
flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.
4. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
5. Terminal numbers are shown for reference only.
6. The lead width as measured 0.36mm (0.014 inch) or greater above the
seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch).
7. Controlling dimension: MILLIMETER. Converted inch dimensions are not
necessarily exact.
8. This outline conforms to JEDEC publication MS-012-AA ISSUE C.
FN7785.3
May 13, 2015
Submit Document Feedback
17
相关型号：
ISL32490EIUZ
±60V Fault Protected, 5V, RS-485/RS-422 Transceivers with ±25V CMR and ESD Protection
INTERSIL
ISL32492EIBZ-T
±60V Fault Protected, 5V, RS-485/RS-422 Transceivers with ±25V CMR and ESD Protection; MSOP8, SOIC8; Temp Range: -40° to 85°C
RENESAS
ISL32492EIBZ-T7A
±60V Fault Protected, 5V, RS-485/RS-422 Transceivers with ±25V CMR and ESD Protection; MSOP8, SOIC8; Temp Range: -40° to 85°C
RENESAS
ISL32492EIUZ-T
±60V Fault Protected, 5V, RS-485/RS-422 Transceivers with ±25V CMR and ESD Protection; MSOP8, SOIC8; Temp Range: -40° to 85°C
RENESAS
ISL32492EIUZ-T7A
±60V Fault Protected, 5V, RS-485/RS-422 Transceivers with ±25V CMR and ESD Protection; MSOP8, SOIC8; Temp Range: -40° to 85°C
RENESAS
©2020 ICPDF网 联系我们和版权申明