EL5161IWZ-T7 [RENESAS]
200MHz Low-Power Current Feedback Amplifiers; SOT5; Temp Range: -40° to 85°C;
| 型号： | EL5161IWZ-T7 |
| 厂家： | 
RENESAS TECHNOLOGY CORP |
| 描述： | 200MHz Low-Power Current Feedback Amplifiers; SOT5; Temp Range: -40° to 85°C 放大器 光电二极管 商用集成电路 |
| 文件： | 总17页 (文件大小：1174K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DATASHEET
EL5160, EL5161, EL5260, EL5261, EL5360
200MHz Low-Power Current Feedback Amplifiers
FN7387
Rev 11.00
August 11, 2015
The EL5160, EL5161, EL5260, EL5261, and EL5360 are
current feedback amplifiers with a bandwidth of 200MHz and
operate from just 0.75mA supply current. This makes these
amplifiers ideal for today’s high speed video and monitor
applications.
Features
• 200MHz -3dB bandwidth
• 0.75mA supply current
• 1700V/µs slew rate
With the ability to run from a single supply voltage from
5V to 10V, these amplifiers are ideal for handheld, portable, or
battery-powered equipment.
• Single and dual supply operation, from 5V to 10V supply span
• Fast enable/disable (EL5160, EL5260 and EL5360 only)
• Available in SOT-23 packages
The EL5160, EL5260, and EL5360 also incorporate an enable
and disable function to reduce the supply current to 14µA
typical per amplifier. Allowing the CE pin to float or applying a
low logic level enables the corresponding amplifier.
• Pb-Free (RoHS compliant)
Applications
• Battery-powered equipment
• Handheld, portable devices
• Video amplifiers
The EL5160 is available in the 6 Ld SOT-23 and 8 Ld SOIC
packages, the EL5161 in 5 Ld SOT-23 package, the EL5260 in
the 10 Ld MSOP package, the EL5261 in 8 Ld SOIC package,
the EL5360 in 16 Ld SOIC and QSOP packages. All operate
over the industrial temperature range of -40°C to +85°C.
• Cable drivers
• RGB amplifiers
• Test equipment
• Instrumentation
• Current-to-voltage converters
Pinouts
EL5160
(8 LD SOIC)
TOP VIEW
EL5160
(6 LD SOT-23)
TOP VIEW
EL5161
(5 LD SOT-23)
TOP VIEW
NC
IN-
1
2
3
4
8
7
6
5
CE
OUT
VS-
IN+
1
2
3
6
5
4
VS+
CE
OUT
VS-
IN+
1
2
3
5
4
VS+
IN-
VS+
OUT
NC
-
+
+
-
+ -
IN+
VS-
IN-
EL5260
(10 LD MSOP)
TOP VIEW
EL5261
(8 LD SOIC)
TOP VIEW
EL5360
(16 LD SOIC, QSOP)
TOP VIEW
OUT
IN-
1
2
3
4
5
10 VS+
OUTA
INA-
INA+
VS-
1
2
3
4
8
7
6
5
VS+
INA+
CEA
VS-
1
2
3
4
5
6
7
8
16 INA-
15 OUTA
14 VS+
-
+
9
8
7
6
OUT
IN-
OUTB
INB-
-
+
-
+
-
IN+
VS-
CE
-
+
+
+
-
IN+
CE
INB+
CEB
INB+
NC
13 OUTB
12 INB-
11 NC
+
-
CEC
INC+
10 OUTC
9
INC-
FN7387 Rev 11.00
August 11, 2015
Page 1 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Ordering Information
PART NUMBER
(Notes 2, 3)
PACKAGE
(Pb-free)
PKG.
DWG. #
PART MARKING
TAPE & REEL
EL5160ISZ
5160ISZ
-
8 Ld SOIC (150 mil)
M8.15E
EL5160ISZ-T7 (Note 1)
EL5160ISZ-T7A (Note 1)
EL5160ISZ-T13 (Note 1)
EL5160IWZ-T7 (Note 1)
EL5160IWZ-T7A (Note 1)
EL5161IWZ-T7 (Note 1)
EL5161IWZ-T7A (Note 1)
5160ISZ
7”
7”
8 Ld SOIC (150 mil)
8 Ld SOIC (150 mil)
8 Ld SOIC (150 mil)
6 Ld SOT-23
M8.15E
5160ISZ
M8.15E
5160ISZ
13”
M8.15E
BAAN (Note 4)
BAAN (Note 4)
BAJA (Note 4)
BAJA (Note 4)
BAAAK
7” (3k pcs)
7” (250 pcs)
7” (3k pcs)
7” (250 pcs)
-
P6.064A
P6.064A
P6.064A
P6.064A
M10.118A
6 Ld SOT-23
5 Ld SOT-23
5 Ld SOT-23
EL5260IYZ
10 Ld MSOP (3.0mm)
(No longer available or supported)
EL5260IYZ-T7 (Note 1)
(No longer available or supported)
BAAAK
7”
13”
-
10 Ld MSOP (3.0mm)
10 Ld MSOP (3.0mm)
8 Ld SOIC (150 mil)
8 Ld SOIC (150 mil)
8 Ld SOIC (150 mil)
16 Ld SOIC (150 mil)
16 Ld SOIC (150 mil)
16 Ld SOIC (150 mil)
16 Ld QSOP (150 mil)
16 Ld QSOP (150 mil)
16 Ld QSOP (150 mil)
M10.118A
M10.118A
M8.15E
EL5260IYZ-T13 (Note 1)
(No longer available or supported)
BAAAK
EL5261ISZ
(No longer available or supported)
5261ISZ
5261ISZ
5261ISZ
EL5360ISZ
EL5360ISZ
EL5360ISZ
5360IUZ
5360IUZ
5360IUZ
EL5261ISZ-T7 (Note 1)
(No longer available or supported)
7”
13”
-
M8.15E
EL5261ISZ-T13 (Note 1)
(No longer available or supported)
M8.15E
EL5360ISZ
(No longer available or supported)
MDP0027
MDP0027
MDP0027
MDP0040
MDP0040
MDP0040
EL5360ISZ-T7 (Note 1)
(No longer available or supported)
7”
13”
-
EL5360ISZ-T13 (Note 1)
(No longer available or supported)
EL5360IUZ(No longer available or
supported)
EL5360IUZ-T7 (Note 1)
(No longer available or supported)
7”
13”
EL5360IUZ-T13 (Note 1)
(No longer available or supported)
NOTES:
1. Please refer to TB347 for details on reel specifications.
2. Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see product information page for EL5160, EL5161, EL5260, EL5261, EL5360. For more information on
MSL, please see tech brief TB363.
4. The part marking is located on the bottom of the part.
FN7387 Rev 11.00
August 11, 2015
Page 2 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
3
Absolute Maximum Ratings (T = +25°C)
Thermal Information
A
Supply Voltage between V + and V -. . . . . . . . . . . . . . . . . . . . . . . . . . 13.2V
Maximum Continuous Output Current. . . . . . . . . . . . . . . . . . . . . . . . . 50mA
Maximum Operating Junction Temperature . . . . . . . . . . . . . . . . . . +125°C
Maximum Power Dissipation . . . . . . . . . . . . . . . . . . . see curves on page 7
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to +150°C
Ambient Operating Temperature Range . . . . . . . . . . . . . . -40°C to +85°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
S
S
Slew Rate of V + to V - . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs
S
S
Pin Voltages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (V -) - 0.5V to (V +) + 0.5V
S
S
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and
operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Electrical Specifications V + = +5V, V - = -5V, R = 750Ω for A = 1, R = 150Ω, V
= V +, V
= (V +) -3V, T = +25°C, Unless
S A
S
S
F
V
L
CE, H
S
CE, L
Otherwise Specified. Boldface limits apply across the operating temperature range, -40°C to +85°C.
MIN
MAX
PARAMETER
AC PERFORMANCE
BW
DESCRIPTION
CONDITIONS
(Note 6)
TYP
(Note 6)
UNIT
-3dB Bandwidth
A
= +1, R = 500Ω
200
125
10
MHz
MHz
MHz
V/µs
V
L
A = +2, R = 150Ω
V
L
BW1
SR
0.1dB Bandwidth
Slew Rate
R
= 100Ω
L
V
= -2.5V to +2.5V, A = +2, R = R = 1kΩ,
900
800
1700
2500
2500
O
V
F
G
R
= 100Ω
L
EL5260, EL5261
1300
1360
35
V/µs
V/µs
ns
SR
500Ω Load
t
0.1% Settling Time
Input Voltage Noise
IN- Input Current Noise
IN+ Input Current Noise
V
= -2.5V to +2.5V, A = +2
S
OUT V
e
4
nV/√Hz
pA/√Hz
pA/√Hz
dBc
N
i -
7
N
i +
N
8
HD2
5MHz, 2.5V , R = 150Ω, A = +2
P-P
-74
-50
0.1
0.1
L
V
HD3
5MHz, 2.5V , R = 150Ω, A = +2
P-P
dBc
L
V
dG
Differential Gain Error (Note 5)
Differential Phase Error (Note 5)
A = +2
%
V
dP
A = +2
°
V
DC PERFORMANCE
V
Offset Voltage
-5
1.6
6
+5
mV
OS
T V
Input Offset Voltage Temperature
Coefficient
Measured from T
to T
MIN MAX
µV/°C
C OS
R
Open Loop Transimpedance Gain
±2.5V
OUT
into 150Ω
800
2000
kΩ
OL
INPUT CHARACTERISTICS
CMIR
CMRR
-ICMR
Common Mode Input Range
Guaranteed by CMRR test
= ±3V
±3
50
-1
±3.3
62
V
dB
Common Mode Rejection Ratio
- Input Current Common Mode Rejection
+ Input Current
V
75
+1
+4
+5
15
IN
µA/V
µA
+I
-4
IN
-I
- Input Current
-5
µA
IN
R
Input Resistance
1.5
4
1
MΩ
pF
IN
C
Input Capacitance
IN
FN7387 Rev 11.00
August 11, 2015
Page 3 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Electrical Specifications V + = +5V, V - = -5V, R = 750Ω for A = 1, R = 150Ω, V
= V +, V = (V +) -3V, T = +25°C, Unless
CE, L S A
Otherwise Specified. Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued)
S
S
F
V
L
CE, H
S
MIN
MAX
PARAMETER
DESCRIPTION
CONDITIONS
(Note 6)
TYP
(Note 6)
UNIT
OUTPUT CHARACTERISTICS
V
Output Voltage Swing
R = 150Ω to GND
±3.1
±3.8
40
±3.4
±4.0
70
±3.8
±4.2
140
V
V
O
L
R = 1kΩ to GND
L
I
Output Current
R = 10Ω to GND
mA
OUT
L
SUPPLY
I
Supply Current - Enabled, per Amplifier
No load, V = 0V (EL5160, EL5161, EL5260,
IN
0.6
0.75
0.85
mA
SON
EL5261)
No load, V = 0V (EL5360)
IN
0.6
0
0.8
10
0.92
25
0
mA
µA
I
I
+
-
Supply Current - Disabled, per Amplifier
Supply Current - Disabled, per Amplifier
Power Supply Rejection Ratio
No load, V = 0V, Only EL5160, EL5260,
IN
EL5360
SOFF
SOFF
-25
65
-14
74
µA
PSRR
-IPSR
DC, V = ±4.75V to ±5.25V
dB
S
- Input Current Power Supply Rejection
DC, V = ±4.75V to ±5.25V
-0.5
0.1
0.5
µA/V
S
ENABLE (EL5160, EL5260, EL5360 ONLY)
t
t
Enable Time
600
800
5
ns
ns
EN
Disable Time
DIS
I
I
CE Pin Input High Current
CE Pin Input Low Current
CE = V +
1
25
1
µA
µA
CE, H
CE, L
S
CE = (V +) - 5V
-1
0
S
NOTE:
5. Standard NTSC test, AC signal amplitude = 286mV , f = 3.58MHz.
P-P
6. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
Typical Performance Curves
3
4
2
1
-1
-3
-5
-7
0
-2
-4
-6
V
V
= +5V
= -5V
= 150Ω
= 2
= 806Ω
= 806Ω
S+
S-
L
V
V
= +5V
= -5V
= 1
= 500Ω
= 2800Ω
S+
S-
R
A
A
V
V
R
R
R
R
L
F
F
G
100k
1M
10M
100M
1G
100k
1M
10M
FREQUENCY (Hz)
100M
1G
FREQUENCY (Hz)
FIGURE 1. FREQUENCY RESPONSE (A = +2)
FIGURE 2. FREQUENCY RESPONSE (A = +1)
V
V
FN7387 Rev 11.00
August 11, 2015
Page 4 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Typical Performance Curves (Continued)
5
4
2
R
R
= 500Ω
= 2.7kΩ
= 1
A = 2
V
L
F
R =150Ω
L
A
R
= R = 762Ω
V
F G
3
1
±5V
±5V
±6V
0
±6V
±4V
±3V
±4V
±3V
-1
-3
-2
-4
-6
±2.5V
±2.5V
-5
100k
1M
10M
FREQUENCY (Hz)
100M
1G
100k
1M
10M
FREQUENCY (Hz)
100M
1G
FIGURE 3. FREQUENCY RESPONSE FOR VARIOUS ±V
FIGURE 4. FREQUENCY RESPONSE FOR VARIOUS
SUPPLY VOLTAGES
S
4
10M
1M
V
V
= +5V
= -5V
= 10
= 500Ω
= 560Ω
S+
S-
A
V
2
0
R
R
L
F
100k
10k
1k
-2
-4
100
10
-6
100k
1M
10M
100M
1G
1k
10k
100k
1M
10M
100M
1G
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 5. FREQUENCY RESPONSE (A = +10)
FIGURE 6. OPEN LOOP TRANSIMPEDANCE GAIN vs FREQUENCY
(R
V
)
OL
OUTPUT
500mV/DIV
INPUT
1V/DIV
INPUT
1V/DIV
OUTPUT
500mV/DIV
V
V
= +5V
= -5V
= 2
S+
S-
V
V
= +5V
= -5V
= 2
S+
S-
A
V
A
V
R
R
= 150Ω
L
F
R
R
= 150Ω
L
F
= R = 422Ω
G
= R = 422Ω
G
4ns/DIV
4ns/DIV
FIGURE 7. OUTPUT RISE TIME
FIGURE 8. OUTPUT FALL TIME
FN7387 Rev 11.00
August 11, 2015
Page 5 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Typical Performance Curves (Continued)
V
V
= +5V
= -5V
S+
S-
CE
5V/DIV
5V/DIV
CE
200mV/DIV
V
OUT
V
200mV/DIV
OUT
V
V
= +5V
= -5V
S+
S-
400ns/DIV
400ns/DIV
FIGURE 9. DISABLE DELAY TIME
FIGURE 10. ENABLE DELAY TIME
0
-20
1K
100
10
V
V
= +5V
= -5V
V
V
= +5V
= -5V
S+
S-
S+
S-
V
S+
-40
-60
1
V
S-
-80
100m
10m
-100
1k
10k
100k
1M
10M
100M
1G
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 11. PSRR vs FREQUENCY
FIGURE 12. CLOSED LOOP OUTPUT IMPEDANCE vs FREQUENCY
4
2
4
V
R
R
= ±5V
= 750Ω
= 150Ω
V
= ±5V
A = -1
V
L
S
G
L
S
R
= 150Ω
R
= 768Ω
2
0
F
0
A
= -2
V
R
= 1kΩ
F
-2
-4
-6
-2
-4
-6
A
= -5
A = +2
V
V
R
= 1.2kΩ
F
R
= 1.5kΩ
F
100k
1M
10M
FREQUENCY (Hz)
100M
1G
100k
1M
10M
FREQUENCY (Hz)
100M
1G
FIGURE 13. FREQUENCY RESPONSE FOR VARIOUS GAIN
SETTINGS
FIGURE 14. FREQUENCY RESPONSE FOR VARIOUS FEEDBACK
RESISTORS, A = -1
V
FN7387 Rev 11.00
August 11, 2015
Page 6 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Typical Performance Curves (Continued)
4
5
3
V
R
R
= ±5V
= 768Ω
= 500Ω
V
= ±5V
A = +1
V
L
S
F
L
S
A
= -5
V
R
= 750Ω
R
= 150Ω
F
2
0
R
= 1kΩ
F
A
= -1
V
1
A
= +5
V
R
= 2.8kΩ
-2
-4
-6
-1
-3
-5
F
A
= +10
V
100k
1M
10M
FREQUENCY (Hz)
100M
1G
100k
1M
10M
FREQUENCY (Hz)
100M
1G
FIGURE 15. FREQUENCY RESPONSE FOR VARIOUS GAIN
SETTINGS
FIGURE 16. FREQUENCY RESPONSE FOR VARIOUS FEEDBACK
RESISTORS, A = +1
V
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1.4
1.4
1.2
1
1.250W
1.2
SO16 (0.150”)
= 80°C/W
1
0.8
0.6
0.4
0.2
0
JA
909mW
435mW
893mW
SO8
= 110°C/W
0.8 870mW
0.6
QSOP16
=112°C/W
JA
JA
MSOP10
=115°C/W
0.4
0.2
0
JA
SOT23-5/6
= 110°C/W
JA
0
25
50
75 85 100
125
150
0
25
50
75 85 100
125
150
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 17. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
FIGURE 18. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1.2
1
0.9
SO16 (0.150”)
1
909mW
= 110°C/W
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
JA
0.8
633mW
SO8
= 160°C/W
625mW
391mW
QSOP16
0.6
JA
= 158°C/W
486mW
JA
0.4
0.2
0
MSOP10
= 206°C/W
SOT23-5/6
= 256°C/W
JA
JA
0
25
50
75 85 100
125
150
0
25
50
75 85 100
125
150
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 19. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
FIGURE 20. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
FN7387 Rev 11.00
August 11, 2015
Page 7 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Pin Descriptions
EL5160
EL5160
PIN
(8 Ld SOIC)
(6 Ld SOT-23) EL5161 EL5260 EL5261 EL5360
NAME
FUNCTION
Not connected
Inverting input
EQUIVALENT CIRCUIT
1, 5
2
-
-
-
-
6, 11
NC
IN-
4
4
2, 8
2, 6
9, 12, 16
V +
S
IN+
IN-
V -
S
Circuit 1
3
4
6
3
2
1
3
2
1
3, 7
4
3, 5
4
1, 5, 8
3
IN+
Non-inverting input (See circuit 1)
Negative supply
V -
S
1, 9
1, 7
10, 13, 15 OUT Output
V +
S
OUT
V -
S
Circuit 2
7
8
6
5
5
-
10
8
-
14
V + Positive supply
S
5, 6
2, 4, 7
CE
Chip enable
V +
S
CE
V -
S
Circuit 3
Power Supply Bypassing and Printed Circuit
Board Layout
Applications Information
Product Description
As with any high frequency device, good printed circuit board
layout is necessary for optimum performance. Low impedance
ground plane construction is essential. Surface mount
components are recommended, but if leaded components are
used, lead lengths should be as short as possible. The power
supply pins must be well bypassed to reduce the risk of
oscillation. The combination of a 4.7µF tantalum capacitor in
parallel with a 0.01µF capacitor has been shown to work well
when placed at each supply pin.
The EL5160, EL5161, EL5260, EL5261, and EL5360 are low
power, current-feedback operational amplifiers that offer a wide
-3dB bandwidth of 200MHz and a low supply current of 0.75mA
per amplifier. The EL5160, EL5161, EL5260, EL5261, and
EL5360 work with supply voltages ranging from a single 5V to
10V and they are also capable of swinging to within 1V of either
supply on the output. Because of their current-feedback topology,
the EL5160, EL5161, EL5260, EL5261, and EL5360 do not
have the normal gain-bandwidth product associated with
voltage-feedback operational amplifiers. Instead, their -3dB
bandwidth remains relatively constant as closed-loop gain is
increased. This combination of high bandwidth and low power,
together with aggressive pricing make the EL5160, EL5161,
EL5260, EL5261, and EL5360 ideal choices for many
For good AC performance, parasitic capacitance should be kept
to a minimum, especially at the inverting input. (See the
“Capacitance at the Inverting Input” section) Even when ground
plane construction is used, it should be removed from the area
near the inverting input to minimize any stray capacitance at that
node. Carbon or Metal-Film resistors are acceptable with the
Metal-Film resistors giving slightly less peaking and bandwidth
because of additional series inductance. Use of sockets,
particularly for the SO package, should be avoided if possible.
Sockets add parasitic inductance and capacitance which results
in additional peaking and overshoot.
low-power/high-bandwidth applications such as portable,
handheld, or battery-powered equipment.
FN7387 Rev 11.00
August 11, 2015
Page 8 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Disable/Power-Down
Supply Voltage Range and Single-Supply
Operation
The EL5160, EL5161, EL5260, EL5261, and EL5360 have been
designed to operate with supply voltages having a span of 5V to
10V. In practical terms, this means that they will operate on dual
supplies ranging from ±2.5V to ±5V. With single-supply, the
EL5160, EL5161, EL5260, EL5261, and EL5360 will operate
from 5V to 10V.
The EL5160, EL5260, EL5360 amplifiers can be disabled,
placing the output in a high impedance state. When disabled, the
amplifier supply current reduces to <15µA. The amplifiers
disable when their CE pin is pulled up to within 1V of the positive
supply. Similarly, the amplifier is enabled by floating or pulling its
CE pin to at least 3V below the positive supply. For a ±5V supply,
this means that an amplifier is enabled when CE is 2V or less,
and disabled when CE is above 4V. Although the logic levels are
not standard TTL, this choice of logic voltages allows an amplifier
to be enabled by tying CE to ground, even in 5V single supply
applications. The CE pin can be driven from CMOS outputs.
As supply voltages continue to decrease, it becomes necessary to
provide input and output voltage ranges that can get as close as
possible to the supply voltages. The EL5160, EL5161, EL5260,
EL5261, and EL5360 have an input range which extends to
within 2V of either supply. So, for example, with ±5V supplies, the
EL5160, EL5161, EL5260, EL5261, and EL5360 have an input
range which spans ±3V. The output range of the EL5160,
EL5161, EL5260, EL5261, and EL5360 is also quite large,
extending to within 1V of the supply rail. On a ±5V supply, the
output is therefore capable of swinging from -4V to +4V.
Single-supply output range is larger because of the increased
negative swing due to the external pull-down resistor to ground.
Capacitance at the Inverting Input
Any manufacturer’s high-speed voltage- or current-feedback
amplifier can be affected by stray capacitance at the inverting
input. For inverting gains, this parasitic capacitance has little
effect because the inverting input is a virtual ground, but for
non-inverting gains, this capacitance (in conjunction with the
feedback and gain resistors) creates a pole in the feedback path
of the amplifier. This pole, if low enough in frequency, has the
same destabilizing effect as a zero in the forward open-loop
response. The use of large-value feedback and gain resistors
exacerbates the problem by further lowering the pole frequency
(increasing the possibility of oscillation.)
Video Performance
For good video performance, an amplifier is required to maintain
the same output impedance and the same frequency response
as DC levels are changed at the output. This is especially difficult
when driving a standard video load of 150Ω, because of the
change in output current with DC level. Previously, good
differential gain could only be achieved by running high idle
currents through the output transistors (to reduce variations in
output impedance.) These currents were typically comparable to
the entire 1mA supply current of each EL5160, EL5161, EL5260,
EL5261, and EL5360 amplifier. Special circuitry has been
incorporated in the EL5160, EL5161, EL5260, EL5261, and
EL5360 to reduce the variation of output impedance with current
output. This results in dG and dP specifications of 0.1% and 0.1°,
while driving 150Ω at a gain of 2.
The EL5160, EL5161, EL5260, EL5261, and EL5360 are
optimized for an 806Ω (A = +2) feedback resistor. With the high
V
bandwidth of these amplifiers, these resistor values might cause
stability problems when combined with parasitic capacitance,
thus ground plane is not recommended around the inverting
input pin of the amplifier.
Feedback Resistor Values
The EL5160, EL5161, EL5260, EL5261, and EL5360 have been
designed and specified at a gain of +2 with R approximately
806. This value of feedback resistor gives 125MHz of -3dB
F
bandwidth at A = 2 with 1dB of peaking. Since the EL5160,
EL5161, EL5260, EL5261, and EL5360 are current-feedback
V
Video performance has also been measured with a 500Ω load at
a gain of +1. Under these conditions, the EL5160 has dG and dP
specifications of 0.1% and 0.1°.
amplifiers, it is also possible to change the value of R to get
F
more bandwidth. As seen in the curve of Frequency Response for
Various R and R on page 5, bandwidth and peaking can be
easily modified by varying the value of the feedback resistor.
F
G
Output Drive Capability
In spite of their low 1mA per amplifier supply current, the
EL5160, EL5161, EL5260, EL5261, and EL5360 are capable of
providing a minimum of ±40mA of output current. With a
minimum of ±40mA of output drive, the EL5160 is capable of
driving 50Ω loads to both rails, making it an excellent choice for
driving isolation transformers in telecommunications
applications.
Because the EL5160, EL5161, EL5260, EL5261, and EL5360 are
current-feedback amplifiers, their gain-bandwidth product is not
a constant for different closed-loop gains. This feature actually
allows the EL5160, EL5161, EL5260, EL5261, and EL5360 to
maintain about the same -3dB bandwidth. As gain is increased,
bandwidth decreases slightly while stability increases. Since the
loop stability is improving with higher closed-loop gains, it
becomes possible to reduce the value of R below the specified
F
806Ω value and still retain stability, resulting in only a slight loss
of bandwidth with increased closed-loop gain.
FN7387 Rev 11.00
August 11, 2015
Page 9 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Driving Cables and Capacitive Loads
Typical Application Circuits
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, the back-termination series resistor will decouple
the EL5160, EL5161, EL5260, EL5261, and EL5360 from the
cable and allow extensive capacitive drive. However, other
applications may have high capacitive loads without a
back-termination resistor. In these applications, a small series
resistor (usually between 5Ω and 50Ω) can be placed in series
0.1µF
+5V
IN+
V +
S
OUT
IN-
V -
S
0.1µF
-5V
500Ω
5Ω
5Ω
with the output to eliminate most peaking. The gain resistor (R )
G
can then be chosen to make up for any gain loss which may be
created by this additional resistor at the output. In many cases it
is also possible to simply increase the value of the feedback
0.1µF
V
OUT
+5V
IN+
resistor (R ) to reduce the peaking.
F
V +
S
OUT
Current Limiting
IN-
V -
S
The EL5160, EL5161, EL5260, EL5261, and EL5360 have no
internal current-limiting circuitry. If the output is shorted, it is
possible to exceed the Absolute Maximum Rating for output
current or power dissipation, potentially resulting in the
destruction of the device.
0.1µF
-5V
500Ω
500Ω
V
IN
FIGURE 21. INVERTING 200mA OUTPUT CURRENT DISTRIBUTION
AMPLIFIER
Power Dissipation
With the high output drive capability of the EL5160, EL5161,
EL5260, EL5261, and EL5360, it is possible to exceed the
+125°C Absolute Maximum junction temperature under certain
500Ω
500Ω
0.1µF
very high load current conditions. Generally speaking when R
L
+5V
IN+
falls below about 25Ω, it is important to calculate the maximum
junction temperature (T ) for the application to determine if
V +
S
JMAX
OUT
power supply voltages, load conditions, or package type need to
be modified for the EL5160, EL5161, EL5260, EL5261, and
EL5360 to remain in the safe operating area. These parameters
are calculated as follows:
IN-
V -
S
0.1µF
500Ω
500Ω
-5V
T
= T
+ n PD
MAX
0.1µF
JMAX
MAX
JA
+5V
IN+
V +
S
where:
• T
V
IN
OUT
V
OUT
IN-
= Maximum ambient temperature
MAX
V -
S
0.1µF
• = Thermal resistance of the package
JA
-5V
• n = Number of amplifiers in the package
FIGURE 22. FAST-SETTLING PRECISION AMPLIFIER
• PD
= Maximum power dissipation of each amplifier in the
package
MAX
PD
for each amplifier can be calculated as follows:
MAX
V
OUTMAX
R
L
----------------------------
PD
= 2 V I
+ V – V
OUTMAX
MAX
S
SMAX
S
where:
• V = Supply voltage
S
• I
SMAX
= Maximum supply current of 0.85mA
= Maximum output voltage (required)
• V
OUTMAX
• R = Load resistance
L
FN7387 Rev 11.00
August 11, 2015
Page 10 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
0.1µF
+5V
0.1µF
+5V
IN+
IN+
V +
V +
S
S
OUT
OUT
IN-
IN-
V -
V -
S
S
0.1µF
0.1µF
-5V
-5V
0.1µF
500Ω
250Ω
250Ω
500Ω
500Ω
V
V
+
OUT
1kΩ
1kΩ
0.1µF
+5V
IN+
240Ω
0.1µF
0.1µF
+5V
IN+
V +
S
OUT
V +
S
-
OUT
IN-
OUT
V
OUT
V -
S
IN-
0.1µF
V -
S
-5V
0.1µF
-5V
500Ω
500Ω
V
IN
500Ω
500Ω
TRANSMITTER
RECEIVER
FIGURE 23. DIFFERENTIAL LINE DRIVER/RECEIVER
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that
you have the latest revision.
DATE
REVISION
CHANGE
August 11, 2015
FN7387.11
Updated Ordering Information table on page 2.
Added Revision History and About Intersil sections.
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support
FN7387 Rev 11.00
August 11, 2015
Page 11 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Small Outline Package Family (SO)
A
D
h X 45°
(N/2)+1
N
A
PIN #1
I.D. MARK
E1
E
c
SEE DETAIL “X”
1
(N/2)
B
L1
0.010 M
C A B
e
H
C
A2
A1
GAUGE
PLANE
SEATING
PLANE
0.010
L
4° ±4°
0.004 C
b
0.010 M
C
A
B
DETAIL X
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
INCHES
SO16
(0.150”)
SO16 (0.300”)
(SOL-16)
SO20
SO24
(SOL-24)
SO28
(SOL-28)
SYMBOL
SO-8
0.068
0.006
0.057
0.017
0.009
0.193
0.236
0.154
0.050
0.025
0.041
0.013
8
SO-14
0.068
0.006
0.057
0.017
0.009
0.341
0.236
0.154
0.050
0.025
0.041
0.013
14
(SOL-20)
0.104
0.007
0.092
0.017
0.011
0.504
0.406
0.295
0.050
0.030
0.056
0.020
20
TOLERANCE
MAX
NOTES
A
A1
A2
b
0.068
0.006
0.057
0.017
0.009
0.390
0.236
0.154
0.050
0.025
0.041
0.013
16
0.104
0.007
0.092
0.017
0.011
0.406
0.406
0.295
0.050
0.030
0.056
0.020
16
0.104
0.007
0.092
0.017
0.011
0.606
0.406
0.295
0.050
0.030
0.056
0.020
24
0.104
0.007
0.092
0.017
0.011
0.704
0.406
0.295
0.050
0.030
0.056
0.020
28
-
0.003
0.002
0.003
0.001
0.004
0.008
0.004
Basic
-
-
-
c
-
D
1, 3
E
-
E1
e
2, 3
-
L
0.009
Basic
-
L1
h
-
Reference
Reference
-
N
-
Rev. M 2/07
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
FN7387 Rev 11.00
August 11, 2015
Page 12 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Package Outline Drawing
P6.064A
6 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE
Rev 0, 2/10
1.90
0-3°
0.08-0.20
0.95
D
A
6
5
4
PIN 1
INDEX AREA
2.80
3
1.60
3
5
0.15 C D
2x
(0.60)
1
2
3
0.20
2x
C
SEE DETAIL X
END VIEW
0.40 ±0.05
3
B
0.20 M C A-B
D
TOP VIEW
10° TYP
(2 PLCS)
5
0.15 C A-B
2x
2.90
H
1.14 ±0.15
1.45 MAX
C
GAUGE
PLANE
(0.25)
0.10
C
SEATING PLANE
0.05-0.15
(0.60)
SIDE VIEW
DETAIL "X"
0.45±0.1
4
(1.20)
NOTES:
(2.40)
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to ASME Y14.5M-1994.
3. Dimension is exclusive of mold flash, protrusions or gate burrs.
4. Foot length is measured at reference to guage plane.
This dimension is measured at Datum “H”.
Package conforms to JEDEC MO-178AA.
5.
6.
(0.95)
(1.90)
TYPICAL RECOMMENDED LAND PATTERN
FN7387 Rev 11.00
August 11, 2015
Page 13 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Package Outline Drawing
P5.064A
5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE
Rev 0, 2/10
1.90
0-3°
0.08-0.20
D
A
5
4
PIN 1
INDEX AREA
2.80
3
1.60
5
3
0.15 C D
2x
(0.60)
2
0.20 C
2x
0.95
SEE DETAIL X
END VIEW
B
0.40 ±0.05
3
0.20 M C A-B D
TOP VIEW
10° TYP
(2 PLCS)
H
5
0.15 C A-B
2x
2.90
1.45 MAX
C
1.14 ±0.15
GAUGE
PLANE
(0.25)
SEATING PLANE
0.10
C
0.45±0.1
4
SIDE VIEW
0.05-0.15
(0.60)
DETAIL "X"
(1.20)
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
(2.40)
2. Dimensioning and tolerancing conform to ASME Y14.5M-1994.
3. Dimension is exclusive of mold flash, protrusions or gate burrs.
4. Foot length is measured at reference to guage plane.
This dimension is measured at Datum “H”.
Package conforms to JEDEC MO-178AA.
5.
6.
(0.95)
(1.90)
TYPICAL RECOMMENDED LAND PATTERN
FN7387 Rev 11.00
August 11, 2015
Page 14 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Package Outline Drawing
M8.15E
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 0, 08/09
4
4.90 ± 0.10
A
DETAIL "A"
0.22 ± 0.03
B
6.0 ± 0.20
3.90 ± 0.10
4
PIN NO.1
ID MARK
5
(0.35) x 45°
4° ± 4°
0.43 ± 0.076
1.27
0.25 M C A B
SIDE VIEW “B”
TOP VIEW
1.75 MAX
1.45 ± 0.1
0.25
GAUGE PLANE
C
SEATING PLANE
0.175 ± 0.075
SIDE VIEW “A
0.10 C
0.63 ±0.23
DETAIL "A"
(0.60)
(1.27)
NOTES:
(1.50)
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
(5.40)
4. Dimension does not include interlead flash or protrusions.
Interlead flash or protrusions shall not exceed 0.25mm per side.
The pin #1 identifier may be either a mold or mark feature.
Reference to JEDEC MS-012.
5.
6.
TYPICAL RECOMMENDED LAND PATTERN
FN7387 Rev 11.00
August 11, 2015
Page 15 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Package Outline Drawing
M10.118A (JEDEC MO-187-BA)
10 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE (MSOP)
Rev 0, 9/09
A
3.0 ± 0.1
DETAIL "X"
0.25 CAB
10
1.10 Max
0.18 ± 0.05
SIDE VIEW 2
B
PIN# 1 ID
1
2
0.95 BSC
0.5 BSC
TOP VIEW
Gauge
Plane
0.86 ± 0.09
0.25
H
C
3°±3°
SEATING PLANE
0.55 ± 0.15
DETAIL "X"
0.10 ± 0.05
0.10 C
0.23 +0.07/ -0.08
0.08 CAB
SIDE VIEW 1
5.80
4.40
3.00
NOTES:
1. Dimensions are in millimeters.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Plastic or metal protrusions of 0.15mm max per side are not
included.
0.50
4. Plastic interlead protrusions of 0.25mm max per side are not
included.
0.30
1.40
5. Dimensions “D” and “E1” are measured at Datum Plane “H”.
6. This replaces existing drawing # MDP0043 MSOP10L.
TYPICAL RECOMMENDED LAND PATTERN
FN7387 Rev 11.00
August 11, 2015
Page 16 of 17
EL5160, EL5161, EL5260, EL5261, EL5360
Quarter Size Outline Plastic Packages Family (QSOP)
A
MDP0040
QUARTER SIZE OUTLINE PLASTIC PACKAGES FAMILY
D
(N/2)+1
N
INCHES
SYMBOL QSOP16 QSOP24 QSOP28 TOLERANCE NOTES
A
A1
A2
b
0.068
0.006
0.056
0.010
0.008
0.193
0.236
0.154
0.025
0.025
0.041
16
0.068
0.006
0.056
0.010
0.008
0.341
0.236
0.154
0.025
0.025
0.041
24
0.068
0.006
0.056
0.010
0.008
0.390
0.236
0.154
0.025
0.025
0.041
28
Max.
±0.002
±0.004
±0.002
±0.001
±0.004
±0.008
±0.004
Basic
-
PIN #1
I.D. MARK
E
E1
-
-
-
1
(N/2)
c
-
B
D
1, 3
0.010 C A B
E
-
e
E1
e
2, 3
H
-
C
SEATING
L
±0.009
Basic
-
PLANE
L1
N
-
0.007 C A B
b
0.004 C
Reference
-
Rev. F 2/07
L1
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not
included.
A
2. Plastic interlead protrusions of 0.010” maximum per side are not
included.
c
SEE DETAIL "X"
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994.
0.010
A2
GAUGE
PLANE
L
A1
4°±4°
DETAIL X
© Copyright Intersil Americas LLC 2004-2015. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN7387 Rev 11.00
August 11, 2015
Page 17 of 17
相关型号：
©2020 ICPDF网 联系我们和版权申明