QPX0002EVB1 [QORVO]
2.5-15 GHz I/Q Mixer;QPX0002
®
2.5-15 GHz I/Q Mixer
Product Overview
Qorvo’s QPX0002 is a compact, wideband I/Q GaAs
mixer housed in a 4 x 4 mm air cavity surface mount
plastic package. Operating over the 2.5 to 15 GHz
bandwidth, the mixer can be configured as an image reject
mixer, a single sideband upconverter, or a QPSK
modulator/demodulator. The QPX0002 utilizes two double
balanced mixer cells and a 90⁰ hybrid internal to the
MMIC. An external 90⁰ IF hybrid is required to complete
the image rejection or sideband suppression. The
QPX0002 is a much smaller alternative to higher cost
hybrid I/Q Mixers and single sideband upconverter
assemblies.
Key Features
•
•
•
•
•
•
•
•
I, Q outputs
RF, LO Frequency Range: 2.5 – 15 GHz
IF Frequency Range: DC – 1 GHz
Low conversion loss of 8 dB at 8 GHz
High image rejection of 22 dB
Functional Block Diagram
High LO/RF isolation > 50 dB at 8 GHz
Wide operating bandwidth
Package dimensions: 4 x 4 x 1.2 mm
Performance is typical across frequency. Please
reference electrical specification table and data plots
for more details.
Applications
• Image reject downconversion
• Single-sideband modulation
• Low noise receiver systems
• Phase detection
• Electronic Warfare (EW)
• QPSK modulation/demodulation
Ordering Information
Part No.
Description
QPX0002SR
100 pcs on 7” reel
QPX0002EVB1
Evaluation Board
Data Sheet | July 2, 2021 | Subject to change without notice
1 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Absolute Maximum Ratings
Recommended Operating Conditions
Parameter
Rating
+25 dBm
150 °C
Parameter
Min
Typ.
Max Units
LO, RF, or IF power, CW, 25 °C
Channel Temperate, Tch
Operating Temperature
Storage Temperature
LO Drive Power
+13
+17
+21
dBm
RF input Power
(downconversion)
+17
dBm
-40 to 85 °C
-55 to 150 °C
260 °C
IF Input Power
(upconversion)
+17
+85
dBm
°C
Mounting Temperature (30 sec)
Temperature Range
-40
+25
Exceeding any one or a combination of the Absolute Maximum Rating
conditions may cause permanent damage to the device. Extended
application of Absolute Maximum Rating conditions to the device may
reduce device reliability.
Electrical specifications are measured at specified test conditions.
Specifications are not guaranteed over all recommended operating
conditions.
Electrical Specifications
Test conditions unless otherwise noted: 25ꢀ°C, IF = 100 MHz USB, LO = +17 dBm
Parameter
Min
Typ.
Max
Units
RF, LO Operational Frequency Range
2.5
–
15
GHz
IF Frequency Range
DC
-11.5
–
–
1
–
–
–
GHz
dB
Conversion Gain (with external 90⁰ IF hybrid)
Image Rejection (with external 90⁰ IF hybrid)
LO to RF Isolation
-8
23
45
dB
–
dB
LO to IF Isolation
Input Power (P1dB)
Input IP3
–
–
–
25
–
–
–
dB
+14
+22
dBm
dBm
Data Sheet | July 2, 2021 | Subject to change without notice
2 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Typical Performance – Data Taken as IRM with External IF Hybrid, IF=100 MHz USB
Conversion Gain vs. Temperature
0
-2
-4
-6
-8
-10
-12
-14
-16
-18
-40 C
+25 C
+85 C
-20
-22
-24
-26
-28
-30
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
Frequency (GHz)
Conversion Gain vs. LO Drive
0
-2
-4
-6
-8
-10
-12
-14
-16
-18
-20
-22
-24
-26
-28
-30
13 dBm
15 dBm
17 dBm
19 dBm
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
Frequency (GHz)
Data Sheet | July 2, 2021 | Subject to change without notice
3 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Typical Performance – Data Taken as IRM with External IF Hybrid, IF=100 MHz USB
Image Rejection vs. Temperature
40
35
30
25
20
15
-40 C
+25 C
+85 C
10
5
0
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
Frequency (GHz)
Input P1dB vs. Temperature
20
18
16
14
12
10
8
6
-40 C
+25 C
+85 C
4
2
0
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
Frequency (GHz)
Data Sheet | July 2, 2021 | Subject to change without notice
4 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Typical Performance – Data Taken as IRM with External IF Hybrid, IF=100 MHz USB
Input IP3 vs. Temperature
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
0
-40 C
+25 C
+85 C
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
Frequency (GHz)
Input IP3 vs. LO Drive Level
33
30
27
24
21
18
15
12
9
13 dBm
15 dBm
17 dBm
19 dBm
6
3
0
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
Frequency (GHz)
Data Sheet | July 2, 2021 | Subject to change without notice
5 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Typical Performance – Data Taken as Upconverter with External IF Hybrid, IF=950 MHz USB
Upconversion Gain vs. LO Drive Level
0
-2
-4
-6
-8
-10
-12
-14
-16
13 dBm
-18
-20
-22
-24
-26
-28
-30
15 dBm
17 dBm
19 dBm
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
LO Frequency (GHz)
Upconverter IP3 vs. LO Drive Level
30
28
26
24
22
20
18
16
14
12
10
8
13 dBm
15 dBm
17 dBm
19 dBm
6
4
2
0
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
LO Frequency (GHz)
Data Sheet | July 2, 2021 | Subject to change without notice
6 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Typical Performance
IF Bandwidth vs. Frequency
0
-2
-4
Return losses measured without IF hybrid
LO=11 GHz, +17 dBm
-6
-8
-10
-12
-14
-16
-18
-20
-22
-24
Conversion Gain
IF1 Return Loss
IF2 Return Loss
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
IF Frequency (GHz)
LO, RF Return Loss vs. Frequency
0
-5
-10
-15
-20
-25
-30
LO Port
RF Port
0
2
4
6
8
10
12
14
16
18
20
Frequency (GHz)
Data Sheet | July 2, 2021 | Subject to change without notice
7 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Typical Performance
Isolations vs. Frequency, LO=17 dBm
0
-10
-20
-30
-40
-50
-60
LO/IF1
LO/IF2
LO/RF
RF/IF1
RF/IF2
Data taken without IF hybrid
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
Frequency (GHz)
Data Sheet | July 2, 2021 | Subject to change without notice
8 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Thermal and Reliability Information
Parameter
Test Conditions
Value
Units
Thermal Resistance (θJC) (1)
279
ºC/W
TBASE = 85 °C, CW,
LO PIN = 17 dBm (0.05 W),
PDISS = 0.05 W
Channel Temperature (TCH) (1)
Median Lifetime (TM)
98.95
7.0E6
°C
Hrs
Notes:
1. Measured to the back of the package.
Spur Performance
nLO
2
mRF
0
x
40
64
1
-9
0
3
4
0
1
2
3
4
20
60
45
16
29
64
59
29
57
65
68
nLO
2
mRF
0
x
44
1
-3
0
3
4
0
1
2
3
4
22
11
28
66
62
24
60
52
RF = 8.1 GHz, -10 dBm
LO = 8 GHz, +17 dBm
All values in dBc below IF output power level (1RF – 1LO)
Data taken as downconverter with no IF hybrid
IF1 response in top table, IF2 response in bottom table.
Data Sheet | July 2, 2021 | Subject to change without notice
9 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Evaluation Board (EVB) Assembly Layout
5
Bill of Materials for QPX0002EVB1
Reference Des.
Value
Description
End Launch Connector
QPX0002 I/Q Mixer
Manuf.
Part Number
J1, J2, J3, J4
U1
Qorvo
PCB
PCB-0018 Evaluation PCB
Data Sheet | July 2, 2021 | Subject to change without notice
10 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Mechanical Information
Recommended PCB Land Pattern
Qorvo recommends that the user develop the land pattern that will provide the best design for proper solder reflow and
device attach for their specific application. Please review Qorvo Application Note AN 105 for a recommended land pattern
approach.
Recommended Solder Reflow Profile
Qorvo recommends screen printing with belt furnace reflow to ensure proper solder reflow and device attach. Please review
Qorvo Application Note AN 102 for a recommended solder reflow profile.
Data Sheet | July 2, 2021 | Subject to change without notice
11 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Pin Diagram
Pin Description
Pad No.
Symbol
Description
1, 5-9, 12, 16-19, 22-24
N/C
No connection required. These pins may be connected to RF/DC ground.
These pins are DC coupled. For applications not requiring operation to DC,
these ports should be DC blocked externally using a series capacitor whose
value has been chosen to pass the necessary IF frequency range. For operation
to DC, these pins must not source or sink more than 16 mA of current or part
non-function or part failure may result.
10, 21
IF2, IF1
3
RF
This pin is AC coupled and matched to 50 Ohms.
This pin is AC coupled and matched to 50 Ohms.
14
LO
2, 4, 11, 13, 15, 20, and
die paddle
Ground
Connect to RF / DC ground
Data Sheet | July 2, 2021 | Subject to change without notice
12 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Assembly Notes
1. Compatible with lead-free soldering processes with 260°C peak reflow temperature.
2. Contact plating: ENEPIG
3. Solder rework not recommended.
4. See Application Note AN102 for further information regarding soldering.
Recommended Soldering Temperature Profile
Data Sheet | July 2, 2021 | Subject to change without notice
13 of 14
www.qorvo.com
QPX0002
®
2.5-15 GHz I/Q Mixer
Handling Precautions
Parameter
Rating
Standard
ESDꢀ–ꢀHuman Body Model (HBM)
Class 1A
ESDAꢁ/ꢁJEDEC JS-001-2012
Caution!
ESD-Sensitive Device
JEDEC standard IPC/JEDEC
J-STD-020
MSLꢀ–ꢀMoisture Sensitivity Level
Level 3
RoHS Compliance
This part is compliant with 2011/65/EU RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment) as amended by Directive 2015/863/EU.
This product also has the following attributes:
• Lead Free
• Antimony Free
• TBBP-A (C15H12Br402) Free
• PFOS Free
• SVHC Free
Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations:
Web: www.qorvo.com
Tel: 1-844-890-8163
Email: customer.support@qorvo.com
Important Notice
The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained
herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained
herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for
Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any
patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by
such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED
HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER
EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical,
life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal
injury or death.
Copyright 2020 © Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc.
Data Sheet | July 2, 2021 | Subject to change without notice
14 of 14
www.qorvo.com
©2020 ICPDF网 联系我们和版权申明