HYB39S128800FT-7 [QIMONDA]
128-MBit Synchronous DRAM; 128兆位同步DRAM型号: | HYB39S128800FT-7 |
厂家: | QIMONDA AG |
描述: | 128-MBit Synchronous DRAM |
文件: | 总21页 (文件大小:1376K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
October 2007
HYB39S128400F[E/T](L)
HY[B/I]39S128800F[E/T](L)
HY[B/I]39S128160F[E/T](L)
HYB39S128407FE
128-MBit Synchronous DRAM
Green Product
SDRAM
Data Sheet
Rev. 1.32
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
HYB39S128400F[E/T](L), HY[B/I]39S128800F[E/T](L), HY[B/I]39S128160F[E/T](L)
Revision History: 2007-10, Rev. 1.32
Page
Subjects (major changes since last revision)
All
23
Adapted Internet Version
Corrected number of refresh cycles
Previous Revision: 2007-06, Rev. 1.31
13
15
19
19
22
22
Corrected operation command "Power Down / Clock suspend ...” in truth table
Corrected text to "After the mode register is set a NOP command is required"
Corrected text to "One clock delay is required for mode entry and exit", chapter 3.5
Corrected the line "Input Capacitances: CK" in table 10, chapter 4
Corrected tCK MIN in table 14
Corrected CLE setup time in table 14
Previous Revision: 2007-03, Rev. 1.30
15
21
22
4
Corrected mode register definition
IDD for low power option 0.8 mA
“Transition time” replaced by “Transition Time of Clock (Rise and Fall)”
Added HYI39S128800FT-7, HYI39S128800FE-7, HYI39S128160FT-7, HYI39S128160FE-7 and
HYB39S128407FE-7
Previous Revision: 2006-10, Rev. 1.20
We Listen to Your Comments
Any information within this document that you feel is wrong, unclear or missing at all?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
techdoc@qimonda.com
qag_techdoc_rev400 / 3.2 QAG / 2006-08-01
10122006-I6LJ-WV3H
2
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
1
Overview
This chapter lists all main features of the product family HY[B/I]39S128[40/80/16][0/7]F[E/T](L) and the ordering information.
1.1
Features
•
•
•
•
•
•
•
•
•
Fully Synchronous to Positive Clock Edge
0 to 70 °C Standard Operating Temperature
-40 to 85 °C Industrial Operating Temperature
Four Banks controlled by BA0 & BA1
•
•
•
•
•
•
•
•
•
Data Mask for Read / Write control (x4, x8)
Data Mask for Byte Control (x16)
Auto Refresh (CBR) and Self Refresh
Power Down and Clock Suspend Mode
4096 refresh cycles / 64 ms (15.6 μs)
Random Column Address every CLK (1-N Rule)
Single 3.3 V ± 0.3 V Power Supply
LVTTL Interface
Programmable CAS Latency: 2 & 3
Programmable Wrap Sequence: Sequential or Interleave
Programmable Burst Length: 1, 2, 4, 8 and full page
Multiple Burst Read with Single Write Operation
Automatic and Controlled Precharge Command
Plastic Packages: P(G)–TSOPII–54 400 mil width
TABLE 1
Performance
Product Type Speed Code
–7
Unit
Speed Grade
PC133–222
—
Max. Clock Frequency
@CL3
@CL2
fCK3
tCK3
tAC3
tCK2
tAC2
143
7
MHz
ns
5.4
7.5
5.4
ns
ns
ns
1.2
Description
The HY[B/I]39S128[40/80/16][0/7]F[E/T](L) are four bank Synchronous DRAM’s organized as 32 MBit x4, 16 MBit x8
and 8 Mbit x16 respectively. These synchronous devices achieve high speed data transfer rates for CAS latencies by
employing a chip architecture that prefetches multiple bits and then synchronizes the output data to a system clock. The chip
is fabricated with Qimonda’s advanced 0.11 μm 128-MBit DRAM process technology.
The device is designed to comply with all industry standards set for synchronous DRAM products, both electrically and
mechanically. All of the control, address, data input and output circuits are synchronized with the positive edge of an externally
supplied clock.
Operating the four memory banks in an interleave fashion allows random access operation to occur at a higher rate than is
possible with standard DRAMs. A sequential and gapless data rate is possible depending on burst length, CAS latency and
speed grade of the device.
Auto Refresh (CBR) and Self Refresh operation are supported. These devices operate with a single 3.3 V ± 0.3 V power supply.
All 128-Mbit components are available in P(G)–TSOPII–54 packages.
Rev. 1.32, 2007-10
3
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
TABLE 2
Ordering Information for Lead-Containing Products
Product Type
Speed Grade
Description
Package
Standard Operating Temperature (0 to 70 °C)
HYB39S128400FT-7
PC133–222–520
143MHz 32M x 4 SDRAM
143MHz 16M x 8 SDRAM
143MHz 8M x 16 SDRAM
P-TSOPII-54
HYB39S128400FTL-7
HYB39S128800FT-7
HYB39S128800FTL-7
HYB39S128160FT-7
HYB39S128160FTL-7
Industrial Operating Temperature (-40 to 85 °C)
HYI39S128800FT-7
HYI39S128160FT-7
PC133–222–520
143MHz 16M x 8 SDRAM
143MHz 8M x 16 SDRAM
P-TSOPII-54
TABLE 3
Ordering Information for RoHS Compliant Products
Product Type
Speed Grade
Description
Package
Note
Standard Operating Temperature (0 to 70 °C)
1)
HYB39S128400FE-7
HYB39S128400FEL-7
HYB39S128407FE-7
HYB39S128800FE-7
HYB39S128800FEL-7
HYB39S128160FE-7
HYB39S128160FEL-7
PC133–222–520
143MHz 32M x 4 SDRAM
PG-TSOPII-54
143MHz 16M x 8 SDRAM
143MHz 8M x 16 SDRAM
Industrial Operating Temperature (-40 to 85 °C)
1)
HYI39S128800FE-7
HYI39S128160FE-7
PC133–222–520
143MHz 16M x 8 SDRAM
143MHz 8M x 16 SDRAM
PG-TSOPII-54
1) RoHS Compliant Product: Restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment as defined
in the directive 2002/95/EC issued by the European Parliament and of the Council of 27 January 2003. These substances include mercury,
lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers.
Rev. 1.32, 2007-10
4
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
2
Chip Configuration
This chapter contains the pin configuration table, the TSOP package drawing, and the block diagrams for the ×4, ×8, ×16
organization of the SDRAM.
2.1
Pin Description
Listed below are the pin configurations sections for the various signals of the SDRAM
TABLE 4
Pin Configuration of the SDRAM
Ball No. Name Pin
Buffer
Function
Type Type
Clock Signals ×4/×8/×16 Organization
38
37
CLK
CKE
I
I
LVTTL
LVTTL
Clock Signal CK
Clock Enable
Control Signals ×4/×8/×16 Organization
18
17
16
19
RAS
CAS
WE
I
I
I
I
LVTTL
LVTTL
LVTTL
LVTTL
Row Address Strobe (RAS), Column Address Strobe (CAS), Write Enable (WE)
CS
Chip Select
Address Signals ×4/×8/×16 Organization
20
21
23
24
25
26
29
30
31
32
33
34
22
35
BA0
BA1
A0
I
I
I
I
I
I
I
I
I
I
I
I
I
I
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
Bank Address Signals 1:0
Address Signal, Address Signal 10/Auto precharge
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
Rev. 1.32, 2007-10
5
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
Ball No. Name Pin
Buffer
Function
Type Type
Data Signals ×4 Organization
5
DQ0
DQ1
DQ2
DQ3
I/O
I/O
I/O
I/O
LVTTL
LVTTL
LVTTL
LVTTL
Data Signal Bus
11
44
50
Data Signals ×8 Organization
2
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
Data Signal Bus
5
8
11
44
47
50
53
Data Signals ×16 Organization
2
DQ0
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
LVTTL
Data Signal Bus
4
DQ1
5
DQ2
7
DQ3
8
DQ4
10
11
13
42
44
45
47
48
50
51
53
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
Data Mask ×4/×8 Organization
39 DQM I/O LVTTL
Data Mask ×16 Organization
Data Mask
39
15
UDQM I/O
LDQM I/O
LVTTL
LVTTL
Data Mask Upper Byte
Data Mask Lower Byte
Rev. 1.32, 2007-10
6
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
Ball No. Name Pin
Buffer
Function
Type Type
Power Supplies ×4/×8/×16 Organization
9
VDDQ
VDD
PWR
PWR
PWR
PWR
–
–
–
–
Power Supply
14
46
41
Power Supply
VSSQ
VSS
Power Supply Ground for DQs
Power Supply Ground
Not connected ×4 Organization
2, 4, 7, 8, NC
10, 13,
15, 36,
40, 42,
45, 47,
48, 51,
53
NC
–
Not connected
Not connected ×8 Organization
4, 7, 10, NC
13, 15,
36, 40,
42, 45,
48, 51
NC
–
Not connected
Not connected
Not connected ×16 Organization
36, 40 NC NC
–
Rev. 1.32, 2007-10
7
10122006-I6LJ-WV3H
ꢀ
[ꢀ
ꢂꢀ
9ꢀ
'4
9ꢀ
'4
9ꢀ
ꢃꢀ
ꢄꢀ
ꢅꢀ
ꢂꢀ
ꢆꢀ
ꢇꢀ
ꢈꢀ
ꢉꢀ
ꢊꢀ
ꢆ
ꢆ
ꢆ
ꢆ
ꢆ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢅ
ꢅ
ꢅ
ꢅ
ꢅ
ꢅ
ꢅ
ꢅ
ꢅ
ꢅ
ꢄ
ꢄ
ꢂꢀ
ꢅꢀ
ꢄꢀ
ꢃꢀ
ꢁꢀ
ꢊꢀ
ꢉꢀ
ꢈꢀ
ꢇꢀ
ꢆꢀ
ꢂꢀ
ꢅꢀ
ꢄꢀ
ꢃꢀ
ꢁꢀ
ꢊꢀ
ꢉꢀ
ꢈꢀ
ꢇꢀ
ꢆꢀ
ꢂꢀ
ꢅꢀ
ꢄꢀ
ꢃꢀ
ꢁꢀ
ꢊꢀ
ꢉꢀ
9ꢀ
9ꢀ
'4
9ꢀ
66ꢀ
''
ꢀ
''
ꢀ
''
ꢀ
66
ꢀ
66
ꢀ
ꢀ
ꢀ
1ꢍ
ꢍꢀ
1ꢍ
9ꢀ
ꢍꢀ
ꢀ
'4ꢃ
ꢁ
ꢁ
&
&
ꢈ
ꢆꢀ
9ꢀ
9ꢀ
9ꢀ
9ꢀ
9ꢀ
''
4
ꢀ
''
4
ꢀ
''
4
ꢀ
66
4
ꢀ
66
4
ꢀ
66
4
ꢀ
'4
'4
ꢀ
ꢀ
1ꢍ
ꢍꢀ
1ꢍ
ꢍꢀ
ꢀ
1ꢍ
'4ꢅꢀ
ꢍꢀ
1ꢍ
ꢍꢀ
ꢀ
'4
'4
9ꢀ
ꢃ
ꢃ
ꢃ
ꢄ
&
&
&
&
ꢇ
ꢂꢀ
ꢅꢀ
'4
ꢀ
'
4ꢁ
'4
9ꢀ
ꢃ
9ꢀ 64
9ꢀ
9ꢀ
9ꢀ
6
ꢀ
66
4
ꢀ
66
4
ꢀ
''
4
ꢀ
''
4
ꢀ
''
4
ꢀ
'4
'4
9ꢀ
ꢀ
ꢀ
1ꢍ
ꢍꢀ
1ꢍ
1ꢍ
9ꢀ
ꢍꢀ
ꢍꢀ
1ꢍ
1ꢍ
9ꢀ
ꢍꢀ
ꢍꢀ
1ꢍ
'4
ꢍꢀ
ꢀ
'4ꢃ
ꢅ
ꢂ
&
&
&
&
&
&
ꢆ
ꢄꢀ
ꢃꢀ
'4
ꢀ
'4ꢃ
ꢄ
9ꢀ
9ꢀ
9ꢀ
''
4
ꢀ
''
4
ꢀ
''
4
ꢀ
66
4
ꢀ
66
4
ꢀ
66
4
ꢀ
'4
'4
ꢀ
ꢀ
1ꢍ
ꢍꢀ
1ꢍ
ꢍꢀ
ꢀ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢄ
ꢄ
ꢄ
ꢄ
ꢄ
ꢄ
ꢄ
ꢄ
ꢁꢀ
1ꢍ
'4ꢄꢀ
ꢍꢀ
1ꢍ
'4
ꢍꢀ
ꢀ
'4
'4
9ꢀ
ꢃ
ꢊ
ꢆ
ꢇ
&
&
&
&
ꢂ
ꢁꢀ
ꢀ
'4
ꢀ
'
4ꢃ
ꢃꢀ
ꢄꢀ
ꢅꢀ
ꢂꢀ
ꢆꢀ
ꢇꢀ
ꢈꢀ
ꢉꢀ
ꢊꢀ
ꢁꢀ
ꢃꢀ
ꢄꢀ
ꢅꢀ
ꢂꢀ
ꢆꢀ
ꢇꢀ
ꢈꢀ
ꢅ
9ꢀ 64
9ꢀ
9ꢀ
9ꢀ
9ꢀ
6
ꢀ
66
4
ꢀ
66
4
ꢀ
''
4
ꢀ
''
4
ꢀ
''4
ꢀ
'4
ꢀ
1ꢍ
ꢍꢀ
1ꢍ
1ꢍ
ꢍꢀ
1ꢍ
9ꢀ
ꢍꢀ
1ꢍ
9ꢀ
ꢍꢀ
'4ꢉ
ꢈ
&
&
&
&
ꢀ
9ꢀ
9ꢀ
9ꢀ
9ꢀ
''
ꢀ
''
ꢀ
''
ꢀ
66
ꢀ
66
ꢀ
66
ꢀ
/
'4
ꢀ
ꢀ
6ꢀ
6ꢀ
ꢁꢀ
ꢁꢀ
ꢃꢀ $
3ꢀ
1ꢍ
ꢍꢀ
ꢀ
6ꢀ
6ꢀ
ꢀ
ꢁꢀ
ꢃꢀ $
3ꢀ
ꢍꢀ
1ꢍ
'4
&.
&.
1ꢍ
ꢃ
ꢅꢀ 1ꢍ
ꢃ
ꢅꢀ 1ꢍ
ꢃ
0
&
&
&ꢍꢋ
0ꢀ
ꢀ
(
&ꢍꢋ
ꢃꢀ
$
&ꢍꢋ
0ꢀ
ꢀ
(
&ꢍꢋ
ꢃꢀ
$
&ꢍꢋ$
ꢅꢀ
ꢄꢀ
:(
&$
5$
&6
%$
:(
&$
5$
:(
ꢀ
'4
&.
&.
8'4
0ꢀ
&
5
$
$
6ꢀ
6ꢀ
&.
&.
ꢀ
(ꢀ
ꢀ
ꢀ
$
&
6ꢁ
&6
%$
ꢁ
ꢀ
ꢄꢀ 1ꢍ
ꢃ
ꢄꢀ 1ꢍ
ꢃ
$ꢃ
&ꢍꢋ$
%$
ꢁꢀ
ꢃꢀ
3ꢀ
$
$
$
$
$
$
$
ꢃ
ꢊꢀ
$
$
$
$
$
$
$
ꢃ
ꢊꢀ
$
$
$
$
$
$
$
ꢃꢃ
ꢊꢀ
ꢀ
$
ꢃ
ꢄꢋ
ꢃ
$
ꢄꢋ
ꢃ
$
ꢃ
$
ꢄꢋ%
$
%$
%
$
ꢃꢁ
ꢌ
ꢁꢌ
ꢃ
ꢁꢌ$
ꢉꢀ
ꢈꢀ
ꢇꢀ
ꢆꢀ
ꢂꢀ
ꢉꢀ
ꢈꢀ
ꢇꢀ
ꢆꢀ
ꢂꢀ
$
$
ꢉꢀ
ꢈꢀ
ꢇꢀ
ꢆꢀ
ꢂꢀ
$
$
$
$
ꢁꢀ
ꢃꢀ
ꢄꢀ
ꢅꢀ
$
$
$
$
ꢁꢀ
ꢃꢀ
ꢄꢀ
ꢅꢀ
$
$
$
$
ꢁꢀ
ꢃꢀ
ꢄꢀ
ꢅꢀ
9ꢀ
9ꢀ
9ꢀ
9ꢀ
9ꢀ
9ꢀ
66
''
ꢀ
''
ꢀ
''
ꢀ
66
ꢀ
66
ꢀ
ꢀ
03
3
6
ꢁ
ꢁ
ꢂꢁꢀ
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
2.2
Package P(G)–TSOPII–54
Listed below are the pin outs of the TSOP package.
FIGURE 1
Pin Configuration P(G)-TSOPII-54
ꢀꢀꢀ
ꢀ
[ꢀꢃ
ꢇꢀ
ꢀ
[ꢀꢉ
Rev. 1.32, 2007-10
10122006-I6LJ-WV3H
8
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
3
Functional Description
This chapter list all defined commands and their usage for this Synchronous DRAM family.
TABLE 5
Truth Table: Operation Command
Operation
Device State
CKE
CKE
n1)2)
DQM BA0
AP=
Addr. CS1 RAS CAS1 WE
1)2)
1)2)
)2)
1)2)
)2)
1)2)
n-11)2)
BA11)2) A101)2)
Bank Active
Bank Precharge
Precharge All
Write
Idle3)
H
H
H
H
H
X
X
X
X
X
X
X
X
X
X
V
V
X
V
V
V
L
V
X
X
V
V
L
L
L
L
L
L
H
H
H
L
H
L
L
L
L
Any
L
Any
H
L
L
Active3)
Active3)
H
H
Write with Auto
precharge
H
L
Read
Active3)
Active3)
H
H
X
X
X
X
V
V
L
V
V
L
L
H
H
L
L
H
H
Read with Auto
precharge
H
Mode Register Set
No Operation
Idle
H
H
H
H
H
H
L
X
X
X
X
H
L
X
X
X
X
X
X
X
V
X
X
X
X
X
X
V
X
X
X
X
X
X
V
X
X
X
X
X
X
L
L
L
L
L
Any
H
H
X
L
H
H
X
L
H
L
Burst Stop
Active
L
Device Deselect
Auto Refresh
Any
H
L
X
H
H
X
X
X
H
X
H
X
Idle
Self Refresh Entry
Self Refresh Exit
Idle
L
L
L
Idle (Self Refr.)
H
H
L
X
H
X
H
X
H
X
X
H
X
H
X
H
X
Power Down/
Clock Suspend Entry or Burst
Active or Idle
H
L
L
X
X
X
X
X
X
X
X
H
L
Power Down/
Clock Suspend Exit
Active or Idle
or Burst
H
H
L
Data Write/
Output Enable
Active
H
H
X
X
L
X
X
X
X
X
X
X
Data Write/
Active
H
X
X
X
X
Output Disable
1) V = Valid, x = Don’t Care, L = Low Level, H = High Level
2) CKEn signal is input level when commands are provided, CKEn-1 signal is input level one clock before the commands are provided.
3) This is the state of the banks designated by BA0, BA1 signals.
Rev. 1.32, 2007-10
9
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
%$ꢃ %$ꢁ $ꢃꢄ $ꢃꢃ $ꢃꢁ $ꢊ
$ꢉ
$ꢈ
$ꢇ
$ꢆ
&/
$ꢂ
$ꢅ
%7
$ꢄ
$ꢃ
%/
$ꢁ
:%/
70
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
Z
Z
Z
Z
UHJꢍꢀDGGU
03%6ꢁꢁꢁꢃ
TABLE 6
Mode Register Definition (BA1:0 = 00B)
Field
BL
Bits
Type
Description
2:0
w
Burst Length
Number of sequential bits per DQ related to one read/write command
Note: All other bit combinations are RESERVED
000B
001B
010B
011B
1
2
4
8
111B Full Page (Sequential burst type only)
BT
CL
3
Burst Type
0B
1B
Sequential
Interleaved
6:4
CAS Latency
Number of full clocks from read command to first data valid window.
Note: All other bit combinations are RESERVED.
010B
011B
2
3
TM
8:7
Test Mode
Note: All other bit combinations are RESERVED.
00B Mode register set
WBL
9
Write Burst Length
0B
1B
Burst write
Single bit write
12:10
Reserved, set to zero
Rev. 1.32, 2007-10
10
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
TABLE 7
Burst Length and Sequence
Burst Length
Starting Column Address
Order of Accesses Within a Burst
A2
A1
A0
Type=Sequential
Type=Interleaved
2
4
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0–1
0–1
1–0
1–0
0
0
1
1
0
0
1
1
0
0
1
1
0–1–2–3
0–1–2–3
1–2–3–0
1–0–3–2
2–3–0–1
2–3–0–1
3–0–1–2
3–2–1–0
8
0
0
0
0
1
1
1
1
n
0–1–2–3–4–5–6–7
1–2–3–4–5–6–7–0
2–3–4–5–6–7–0–1
3–4–5–6–7–0–1–2
4–5–6–7–0–1–2–3
5–6–7–0–1–2–3–4
6–7–0–1–2–3–4–5
7–0–1–2–3–4–5–6
Cn, Cn+1, Cn+2 ....
0–1–2–3–4–5–6–7
1–0–3–2–5–4–7–6
2–3–0–1–6–7–4–5
3–2–1–0–7–6–5–4
4–5–6–7–0–1–2–3
5–4–7–6–1–0–3–2
6–7–4–5–2–3–0–1
7–6–5–4–3–2–1–0
Not supported
FullPage
Notes
1. For a burst length of two, A1-Ai selects the two-data-element block; A0 selects the first access within the block.
2. For a burst length of four, A2-Ai selects the four-data-element block; A0-A1 selects the first access within the block.
3. For a burst length of eight, A3-Ai selects the eight-data- element block; A0-A2 selects the first access with in the block.
4. Whenever a boundary of the block is reached within a given sequence above, the following access wraps within the block.
Rev. 1.32, 2007-10
11
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
4
Electrical Characteristics
4.1
Operating Conditions
TABLE 8
Absolute Maximum Ratings
Parameter
Symbol
Limit Values
Min.
Unit
Note/
Test Condition
Max.
Input / Output voltage relative to VSS
Voltage on VDD supply relative to VSS
Voltage on VDDQ supply relative to VSS
Operating Temperature for HYB...
Operating Temperature for HYI...
Storage temperature range
VIN, VOUT
VDD
– 1.0
– 1.0
– 1.0
0
+4.6
+4.6
+4.6
+70
+85
+150
1
V
–
–
–
–
–
–
–
–
V
VDDQ
TA
V
°C
°C
°C
W
mA
TA
-40
-55
–
TSTG
PD
Power dissipation per SDRAM component
Data out current (short circuit)
IOUT
–
50
Attention: Stresses above the max. values listed here may cause permanent damage to the device. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings
are absolute ratings; exceeding only one of these values may cause irreversible damage to the integrated
circuit.
Rev. 1.32, 2007-10
12
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
TABLE 9
DC Characteristics
Parameter
Symbol
Values
Unit Note/
Test Condition
Min. Max.
1)2)
1)2)
1)2)3)
1)2)3)
1)2)
1)2)
1)
Supply Voltage
VDD
VDDQ
VIH
3.0 3.6
3.0 3.6
V
V
I/O Supply Voltage
Input high voltage
2.0
VDDQ+0.3 V
Input low voltage
VIL
– 0.3 +0.8
V
Output high voltage (IOUT = – 4.0 mA)
Output low voltage (IOUT = 4.0 mA)
VOH
VOL
2.4
–
–
V
0.4
V
Input leakage current, any input(0 V < VIN < VDD, all other inputs = 0 V) IIL
– 5 +5
– 5 +5
μA
μA
1)
Output leakage current(DQs are disabled, 0 V < VOUT < VDDQ
)
IOL
1) TA = 0 to 70 ºC
2) All voltages are referenced to VSS
3)
V
IH may overshoot to VDDQ + 2.0 V for pulse width of < 4ns with 3.3 V. VIL may undershoot to -2.0 V for pulse width < 4.0 ns with 3.3 V.
Pulse width measured at 50% points with amplitude measured peak to DC reference.
TABLE 10
Input and Output Capacitances
Parameter
Symbol
Values1)
Unit
Note
Min.
Max.
2)
2)
Input Capacitances: CK
CI1
CI2
2.5
2.5
3.5
3.8
pF
pF
Input Capacitance
(A0-A11, BA0, BA1, RAS, CAS, WE, CS, CKE, DQM)
2)
Input/Output Capacitance (DQ)
CI0
4.0
6.0
pF
1) Capacitance values are shown for TSOP-54 packages. Capacitance values for TFBGA packages are lower by 0.5 pF
2) TA = 0 to 70 ºC; VDD,VDDQ = 3.3 V ± 0.3 V, f = 1 MHz
Rev. 1.32, 2007-10
13
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
TABLE 11
IDD Conditions
Parameter
Symbol
Operating Current
IDD1
One bank active, Burst length = 1
Precharge Standby Current in Power Down Mode
Recharge Standby Current in Non-Power Down Mode
IDD2P
IDD2N
IDD3N
IDD3P
IDD4
No Operating Current
Active state (max. 4 banks)
Burst Operating Current
Read command cycling
Auto Refresh Current
Auto Refresh command cycling
IDD5
IDD6
Self Refresh Current (standard components)
Self Refresh Mode, CKE=0.2 V, tCK=infinity
Self Refresh Current (low power components)
Self Refresh Mode, CKE=0.2 V, tCK=infinity
TABLE 12
DD Specifications and Conditions
I
Symbol
–7
Unit
Note/ Test Condition
Max.
1)2)3)4)
1)2)
IDD1
t
RC = tRC(min), IO = 0 mA
80
2
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
IDD2P
IDD2N
IDD3N
IDD3P
IDD4
CS =VIH (min.), CKE ≤VIL(max)
CS =VIH (min.), CKE≥ VIH(min)
CS = VIH(min), CKE ≥VIH(min.)
CS = VIH(min), CKE ≤ VIL(max.)
1)2)
22
35
5
1)2)
1)2)
1)2)4)
1)2)5)
1)2)
65
146
25
3
IDD5
t
t
RFC= tRFC(min)
RFC= 15.6 μs
IDD6
1)2) Standard components
1) Low power components at 85 °C
0.8
1) Currents values will be added when available.
2) TA = 0 to 70 °C; VSS = 0 V; VDD, VDDQ = 3.3 V ± 0.3 V
3) These parameters depend on the cycle rate. All values are measured at 133 MHz for -7 with the outputs open. Input signals are changed
once during tCK
.
4) These parameters are measured with continuous data stream during read access and all DQ toggling. CL=3 and BL=4 is assumed and
the VDDQ current is excluded.
5)
tRFC= tRFC(min) “burst refresh”, tRFC= 15.6 μs “distributed refresh”.
Rev. 1.32, 2007-10
14
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
4.2
AC Characteristics
TABLE 13
AC Timing - Absolute Specifications –7
Parameter
Symbol
–7
Unit Note
PC133– 222
Min.
Max.
Clock and Clock Enable
Clock Frequency
tCK
tAC
7
7.5
—
—
ns
ns
CL3 1)2)3)
CL2 1)2)3)
CL31)2)3)
CL21)2)3)4)5)
1)2)3)
Access Time from Clock
—
—
5.4
5.4
ns
ns
Clock High Pulse Width
Clock Low Pulse Width
tCH
tCL
tT
2.5
2.5
0.3
—
ns
ns
ns
1)2)3)
1)2)3)
—
Transition Time of Clock (Rise and Fall)
Setup and Hold Times
Input Setup Time
1.2
1)2)3)6)
1)2)3)6)
1)2)3)6)
1)2)3)6)
1)2)3)
tIS
1.5
0.8
1.5
0.8
2
—
—
—
—
—
7
ns
ns
ns
ns
tCK
ns
Input Hold Time
tIH
CKE Setup Time
tCKS
tCKH
tRSC
tSB
CKE Hold Time
Mode Register Set-up to Active delay
Power Down Mode Entry Time
Common Parameters
1)2)3)
0
1)2)3)7)
1)2)3)7)
1)2)3)7)
1)2)3)7)
1)2)3)
Row to Column Delay Time
Row Precharge Time
tRCD
tRP
tRAS
tRC
15
15
37
60
63
14
1
—
ns
ns
ns
ns
ns
ns
tCK
—
Row Active Time
100k
—
Row Cycle Time
Row Cycle Time during Auto Refresh
Activate(a) to Activate(b) Command period
CAS(a) to CAS(b) Command period
Refresh Cycle
tRFC
tRRD
tCCD
—
1)2)3)7)
1)2)3)
—
—
1)2)3)
Refresh Period (4096 cycles)
Self Refresh Exit Time
tREF
tSREX
tOH
–
1
3
64
—
—
ms
tCK
ns
1)2)3)
1)2)3)5)
Data Out Hold Time
Read Cycle
1)2)3)
1)2)3)
1)2)3)
Data Out to Low Impedance Time
Data Out to High Impedance Time
DQM Data Out Disable Latency
tLZ
0
—
7
ns
ns
tCK
tHZ
3
tDQZ
—
2
Rev. 1.32, 2007-10
15
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
Parameter
Symbol
–7
Unit Note
PC133– 222
Min.
Max.
Write Cycle
1)2)3)8)
Last Data Input to Precharge
(Write without Auto Precharge)
tWR
14
0
—
ns
1)2)3)9)
1)2)3)
Last Data Input to Activate(Write with Auto Precharge)
DQM Write Mask Latency
tDAL(min.)
tDQW
tCK
tCK
—
1) TA = 0 to 70 °C; VSS = 0 V; VDD, VDDQ = 3.3 V ± 0.3 V, tT = 1 ns
2) For proper power-up see the operation section of this data sheet.
3) AC timing tests for LV-TTL versions have VIL = 0.4 V and VIH = 2.4 V with the timing referenced to the 1.4 V crossover point. The transition
time is measured between VIH and VIL. All AC measurements assume tT = 1 ns with the AC output load circuit shown in figure below.
Specified tAC and tOH parameters are measured with a 50 pF only, without any resistive termination and with an input signal of 1V / ns edge
rate between 0.8 V and 2.0 V.
4) If clock rising time is longer than 1 ns, a time (tT/2 - 0.5) ns has to be added to this parameter.
5) Access time from clock tac is 4.6 ns for PC133 components with no termination and 0 pF load,Data out hold time toh is 1.8 ns for PC133
components with no termination and 0 pF load.
6) If tT is longer than 1 ns, a time (tT - 1) ns has to be added to this parameter.
7) These parameter account for the number of clock cycles and depend on the operating frequency of the clock, as follows:the number of
clock cycles = specified value of timing period (counted in fractions as a whole number)
8) It is recommended to use two clock cycles between the last data-in and the precharge command in case of a write command without Auto-
Precharge. One clock cycle between the last data-in and the precharge command is also supported, but restricted to cycle times tCK greater
or equal the specified tWR value, where tck is equal to the actual system clock time.
9) When a Write command with Auto Precharge has been issued, a time of tDAL(min) has be fullfilled before the next Activate Command can
be applied. For each of the terms, if not already an integer, round up to the next highest integer. tCK is equal to the actual system clock time.
FIGURE 2
Measurement conditions for tAC and tOH
tCH
2.4 V
0.4 V
1.4 V
CLOCK
tT
tCL
tIH
tIS
INPUT
1.4 V
tAC
tAC
tLZ
tOH
OUTPUT
1.4 V
I/O
50 pF
tHZ
Measurement conditions for
AC and tOH
IO.vsd
t
Rev. 1.32, 2007-10
16
10122006-I6LJ-WV3H
ꢁꢍ
ꢃꢅꢀ
ꢃ
ꢁꢍꢃꢇꢀ
ꢆ
ꢀꢀ
ꢃꢆꢀꢀ
ꢁꢍꢉ
ꢀ
ꢁꢍ
ꢁꢍ
ꢃꢀ
ꢄꢀ
ꢅꢎꢀ
ꢆꢀꢀ
ꢁꢍꢆꢀ
ꢃꢆꢀꢀ
ꢁꢍꢃ
ꢀ
ꢁꢍ
ꢁꢉ
ꢀ
ꢆ
ꢂ
[ꢀ
ꢁꢍ
ꢅꢀ
ꢃ
ꢃꢍꢈꢇꢀ
6
,1
ꢆ
*ꢀ3
/
$
1(
(
$7
ꢀ
ꢄ
ꢁꢍꢉ
ꢀꢀ ꢀ ꢀꢀꢄꢁꢍꢉꢀ
ꢇꢀ[ꢀꢀ
ꢂ[ꢀ
ꢁꢍ
ꢄꢀ
ꢆꢂ
ꢀ
ꢄꢉꢀ
ꢃꢀ
ꢄꢈꢀ
ꢄꢍꢆ
ꢀ
0$
;ꢍꢀ
ꢁꢍ
ꢃꢅꢀ
ꢄ
ꢄꢄꢀ
ꢄꢍ
,Q
0D
NL
G
H[ꢀ
U
Q
Jꢀ
ꢃꢎꢀ
ꢄꢎꢀ
ꢅꢎꢀ
'R
'R
'R
Q
Q
Q
L
L
L
WL
WL
H
S
U
XV
ꢁꢍꢄ
Iꢀꢁꢍꢃ
L
ꢍ
ꢃ
D
L
H
H
H
Vꢀ
Vꢀ
Vꢀ
R
R
R
Wꢀ
Wꢀ
Wꢀ
Q
Q
Q
FO
FO
FO
X
X
X
G
G
G
HꢀS
HꢀS
HꢀG
O
O
D
D
V
V
FꢀR
FꢀS
UꢀP
WU
WU
WD
Oꢀ
UR
Qꢀ
Qꢀ
W
R
QꢀR
ꢆꢀP
ꢅꢀP
Iꢀꢁ
[ꢍꢀS
[ꢍꢀS
ꢆꢀP
UꢀVL
Uꢀ
[ꢍꢀS
H
UꢀV
G
Hꢀ
X
R
D
U
R
VL
R
Iꢀ
R
H
G
Hꢀ
Hꢀ
E
S
X
D
VL
D
P
D
Uꢀ
U
R
VL
R
H
G
*
ꢁꢉꢉꢀꢀ
3;ꢁꢃ
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
5
Package Outlines
FIGURE 3
Package Outline PG-TSOPII-54-4 (top view)
ꢄꢎꢀ
0ꢀ
ꢃꢎꢀ
Notes
1. Drawing according to ISO 8015
2. Dimensions in mm
3. General tolerances +/- 0.15
Rev. 1.32, 2007-10
17
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
List of Figures
Figure 1
Figure 2
Figure 3
Pin Configuration P(G)-TSOPII-54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Measurement conditions for tAC and tOH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Package Outline PG-TSOPII-54-4 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Rev. 1.32, 2007-10
18
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
List of Tables
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Ordering Information for Lead-Containing Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Ordering Information for RoHS Compliant Products. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin Configuration of the SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Truth Table: Operation Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mode Register Definition (BA1:0 = 00B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Burst Length and Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Input and Output Capacitances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IDD Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
I
DD Specifications and Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
AC Timing - Absolute Specifications –7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Rev. 1.32, 2007-10
19
10122006-I6LJ-WV3H
Data Sheet
HY[B/I]39S128[40/80/16][0/7]F[E/T](L)
128-MBit Synchronous DRAM
Table of Contents
1
1.1
1.2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
2.1
2.2
Chip Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Package P(G)–TSOPII–54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4
4.1
4.2
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Rev. 1.32, 2007-10
20
10122006-I6LJ-WV3H
Data Sheet
Edition 2007-10
Published by Qimonda AG
Gustav-Heinemann-Ring 212
D-81739 München, Germany
© Qimonda AG 2007.
All Rights Reserved.
Legal Disclaimer
The information given in this Data Sheet shall in no event be regarded as a guarantee of conditions or characteristics
(“Beschaffenheitsgarantie”). With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Qimonda hereby disclaims any and all warranties and liabilities of any kind,
including without limitation warranties of non-infringement of intellectual property rights of any third party.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest Qimonda Office.
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in question please
contact your nearest Qimonda Office.
Qimonda Components may only be used in life-support devices or systems with the express written approval of Qimonda, if a
failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect
the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human
body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health
of the user or other persons may be endangered.
www.qimonda.com
相关型号:
©2020 ICPDF网 联系我们和版权申明