FES200ZG-A [POWER-ONE]
300 WATT; 300瓦
POWER-ONE 
ꢀꢀ
ꢀꢀ
(888) IPD-CONVerters
(888) 473-2668
www.ipdconverters.com
FES SERIES - 300 WATT
DESCRIPTION
FEATURES
FES single output DC/DC converters provide up to
300 Watts of output power and up to 60 Amperes of
output current in a full brick package. The FES
converters feature open-frame packaging, along with
planar magnetics and a high efficiency topology, to
provide maximum useable power density. The FES
converters use 100% surface-mount construction and
are fully compatible with production board washing
processes.
• 60A “Full Brick”
• Very High Efficiency
• Open-Frame Packaging
• 100°C Baseplate
Operation
• Planar Magnetics
• Excellent Transient
Response
• 1500V Isolation
• Synchronous
Rectification
TECHNICAL SPECIFICATIONS
Input
Voltage Range
48 VDC Nominal
Undervoltage Lockout - Turn on / Turn off
36 - 75 VDC
34 / 32 VDC
Output
Setpoint Accuracy
±1%
Line Regulation Vin Min. - Vin Max., Iout Rated
0.2% Vout
Load Regulation Iout Min. - Iout Max., Vin Nom.
Remote Sense Headroom
0.2% Vout
0.5 VDC
Efficiency vs. Load (48V Input)
Minimum Output Current
10 % Iout Rated
95
90
85
80
75
70
65
60
Dynamic Regulation, Loadstep
Pk Deviation
Settling Time
25% Iout
4% Vout
500 µs
Voltage Trim Range
±10%
Current Limit Threshold Range, % of Iout Rated
OVP Trip Range
110 - 140%
FES200ZE-A
120 - 140% Vout Nom.
EFF. (36V)
EFF. (48V)
EFF. (75V)
OVP Type
Short Circuit/Over Current Protection
Self Recovering
Shutdown/Hiccup
General
10
20
30
40
50
60
70
80
90
100
Turn-On Time
10 ms
LOAD %
Remote Shutdown
Positive Logic
Remote Shutdown Reference
Switching Frequency
Isolation
Vin Negative
200 or 300 kHz
Input - Output
Input - Case
Output - Case
Temperature Coefficient
Case Temperature
Operating Range
1500 VDC
1050 VDC
500 VDC
0.03%/°C
Notes
MTBF predictions may vary slightly from model to model.
†
Specifications typically at 25°C, normal line, and full load, unless otherwise
stated.
-40 To +100°C
-40 To +125°C
105 To 125°C
5 g, 10 - 55 Hz
Consult Factory
UL, CUL, TUV
4.4 oz
Storage Range
Thermal Shutdown Range
Vibration, 3 Axes, 5 Min Each
MTBF† (Bellcore TR-NWT-000332)
Safety
Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with
commercial wave-soldering equipment.
Safety: Agency approvals may vary from model to model. Please consult factory
for specific model information.
Weight (Approx.)
C-56
FES SERIES - 300 WATT
MODELS - (See the last page of this file for options.)
Vin
(Volts)
Vin Range
(Volts)
Iin Max.*
(Amps)
Vout
(Volts)
Iout Rated
(Amps)
Ripple & Noise
Pk-Pk (mV)
Efficiency
Typ. **
Model
48
48
48
48
48
48
36 - 75
36 - 75
36 - 75
36 - 75
36 - 75
36 - 75
3.5
4.5
6.5
5.0
7.0
10.5
2.5
3.3
5.0
2.5
3.3
5.0
40
40
40
60
60
60
100
100
100
100
100
100
85%
87%
80%
79%
81%
84%
FES100ZD-A
FES132ZE-A
FES200ZG-A
FES150ZD-A
FES200ZE-A
FES300ZG-A
* Maximum input current at minimum input voltage, maximum rated output power.
** At nominal Vin, rated output.
MECHANICAL DRAWING
Thermal Impedance
Pin
Tolerances
Function
Inches:
.XX ± 0.020
.XXX ± .010
(Millimeters)
.X ± 0.5
.XX ± 0.25
Natural Convection
100 LFM
200 LFM
300 LFM
400 LFM
5.4 °C/W
3.8 °C/W
2.5 °C/W
1.7 °C/W
1.6 °C/W
1
2
3
-Vin
Case
Enable
4
5
6
+Vin
-Vout
-Vout
Pin:
± 0.002
± 0.05
7
8
9
-Sense
Trim
+Sense
( Dimensions as listed unless otherwise
specified.)
Note:
Thermal impedance data is dependent on
many environmental factors. The exact
thermal performance should be validated for
specific application.
10
11
+Vout
+Vout
C-57
OPTIONS
When ordering equipment options, use the following suffix information. Select the option(s) that
you prefer and add them to the model number. Example ordering options are located below the
options table.
OPTION
Negative Logic
SUFFIX
APPLICABLE SERIES
REMARKS
N
HAS, HBD, HBS, HES, LES, QBS,
QES, TES, TQD
TTL “Low” Turns Module ON
TTL “High” Turns Module OFF
Lucent Compatible Trim
Terminal Strip
Trim
T
TS
1
HAS, HBD, HBS, HES, QBS, QES
XWS, XWD, XWT
IAS, LES
Enable
2
IAD, IAS, LES, SMS
IAS, LES
Trim and Enable
Current Share
Headerless
3
4
SMS
Y
Encapsulated EWS, IWS, OWS
PIN LENGTH AND HEATSINK
OPTIONS
Standard Pin Length is 0.180”
(4.6mm)
0.110” (2.8mm) Pin Length
0.150” (3.8mm) Pin Length
0.24” (6.1mm) Horizontal Heatsink
8
9
All Units (Except SMS)
All Units (Except SMS)
1H
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
0.24” (6.1mm) Vertical Heatsink
1V
2H
2V
3H
3V
All Units (Except DIP, SIP, and SM
Packages)
0.45” (11.4mm) Horizontal
Heatsink
All Units (Except DIP, SIP, and SM
Packages)
0.45” (11.4mm) Vertical Heatsink
All Units (Except DIP, SIP, and SM
Packages)
0.95” (24.1mm) Horizontal
Heatsink
All Units (Except DIP, SIP, and SM
Packages)
0.95” (24.1mm) Vertical Heatsink
All Units (Except DIP, SIP, and SM
Packages)
Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and
0.95” vertical heatsink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length.
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
C105
相关型号：
©2020 ICPDF网 联系我们和版权申明