2834876 [PHOENIX]
Power/Signal Relay;
| 型号： | 2834876 |
| 厂家： | 
PHOENIX CONTACT |
| 描述： | Power/Signal Relay 继电器 |
| 文件： | 总4页 (文件大小：240K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PLC-…24UC/1/S/H
PLC-…24UC/1/S/L
PLC INTERFACE With Switch and Integrated
Power Contact Relay
INTERFACE
Data Sheet
101460_en_04
© PHOENIX CONTACT - 03/2008
inserted in the bridge shafts. They eliminate the need for
complicated and time-consuming loop bridges.
1
Description
The 6.2 mm PLC-…24UC/1/S… PLC INTERFACE module
supports "Manual", "Zero", and "Automatic" functions. The
load can be switched directly using the module.
1.3
Additional Advantages
–
Environmentally friendly, cadmium-free power contact
material for loads up to 250 V AC/6 A
1.1
Switching Function
–
–
–
–
–
Integrated input/protective circuit
Depending on the version, the switch can be operated either
by hand or using a screwdriver.
A floating contact provides confirmation for the "Automatic"
switching state.
Safe isolation according to DIN EN 50178
Spring-cage and screw connection types available
6 kVrms electrical isolation between coil and contact
Floating confirmation contact for "Automatic" switching
state
1.2
Optimum Use of Plug-In Bridges
The PLC INTERFACE module achieves maximum
efficiency with the user-friendly FBST plug-in bridge system.
The PLC-…24UC/1/S… makes effective use of the bridging
options for the A1/A2 connection on the coil side, for the
supply at connection 13 on the contact side, and for the
manual input at connection M. Especially effective here are
the 500 mm long color-insulated continuous plug-in bridges
that can easily be cut to the required length and quickly
Make sure you always use the latest documentation.
It can be downloaded at www.download.phoenixcontact.com.
A conversion table is available on the Internet at
www.download.phoenixcontact.com/general/7000_en_00.pdf.
This data sheet is valid for all products listed on the following page:
PLC-…24UC/1/S…
2
Ordering Data
PLC INTERFACE With Switch (Operation by Hand)
Description
PLC INTERFACE with switch (operation by hand) and integrated power
contact relay for "Manual", "Zero", and "Automatic" functions, with screw
connection, for mounting on 3
Type
PLC-RSC- 24UC/1/S/H
Order No.
2982236
Pcs./Pck.
10
PLC INTERFACE with switch (operation by hand) and integrated power
contact relay for "Manual", "Zero", and "Automatic" functions, with spring-cage
connection, for mounting on 3
PLC-RSP- 24UC/1/S/H
2982249
10
PLC INTERFACE With Switch (Operation Using a Screwdriver)
Description Type
PLC INTERFACE with switch (operation using a screwdriver) and integrated PLC-RSC- 24UC/1/S/L
power contact relay for "Manual", "Zero", and "Automatic" functions, with
screw connection, for mounting on 3
Order No.
2834876
Pcs./Pck.
10
PLC INTERFACE with switch (operation using a screwdriver) and integrated PLC-RSP- 24UC/1/S/L
power contact relay for "Manual", "Zero", and "Automatic" functions, with
spring-cage connection, for mounting on 3
2834889
10
For the protection of input and output, inductive loads must be dampened with an effective protective circuit.
Accessories
Description
Insulating plate
Type
PLC-ATP BK
Order No.
2966841
Pcs./Pck.
25
The PLC-ATP BK insulating plate should be used in the following cases: always fit at the start and end of a PLC terminal strip for voltages
greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules (FBST 8-PLC... or FBST 500... can be used for
potential bridging) and for safe isolation between adjacent modules.
For additional accessories such as power terminal blocks and plug-in bridges, please refer to the INTERFACE catalog or www.phoenixcontact.com.
101460_en_04
PHOENIX CONTACT
2
PLC-…24UC/1/S…
3
Technical Data
Input Data
Input voltage U
24 V AC/DC, 50 Hz ... 60 Hz
See "Operating Voltage Range" on page 4
11 mA
N
Permissible range (with reference to U
Typical input current at U
Input circuit
)
N
N
Yellow LED, bridge rectifier
Output Data
Contact type
Contact material
Maximum switching voltage
Minimum switching voltage
Limiting continuous current
Maximum inrush current
Minimum switching current
Maximum shutdown power
Single contact, 1 N/O contact
Silver tin oxide AgSnO
250 V AC/DC
12 V AC/DC
6 A
On request
10 mA
1
Ohmic load τ = 0 ms
24 V DC 140 W
48 V DC 20 W
60 V DC 18 W
110 V DC 23 W
220 V DC 40 W
250 V AC 1500 VA
120 mW
Minimum switching power
1
The PLC-ATP BK insulating plate must be installed for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules
(see "Accessories"). FBST 8-PLC... or FBST 500... is then used for potential bridging.
General Data
Rated insulation voltage
250 V AC
6 kV
Impulse voltage withstand level
Ambient temperature range
Operation
-25°C ... 60°C
Storage/transport
-20°C ... 85°C
Nominal operating mode
100% operating factor
Inflammability class according to UL 94 (housing)
Air and creepage distances between the circuits
Standards/specifications
V0
DIN EN 50178/VDE 0160 (safe isolation, reinforced insulation I/O)
IEC 60664, IEC 60664 A, DIN VDE 0110, DIN EN 50155/VDE 0115-200 (in
relevant parts), IEC 60255/DIN VDE 0435 (in relevant parts)
Pollution degree
2
Surge voltage category
Mounting position
III
Any
Mounting
Can be aligned without spacing
Conductor cross-section
Solid, with screw connection
Stranded, with screw connection
Solid, with spring-cage connection
Stranded, with spring-cage connection
Stripping length
2
2
0.14 mm ... 2.5 mm (26 - 14 AWG)
2
2
0.14 mm ... 1.5 mm (26 - 14 AWG)
2
2
0.2 mm ... 2.5 mm (24 - 14 AWG)
0.2 mm ... 1.5 mm (24 - 14 AWG)
2
2
Screw connection
10 mm
Spring-cage connection
Dimensions (W x H x D)
Housing material
8 mm
6.2 mm x 94 mm x 80 mm
Polybutylene terephthalate PBT, non-reinforced, green
101460_en_04
PHOENIX CONTACT
3
PLC-…24UC/1/S…
Confirmation
"Automatic" mode, floating
30 V AC/DC / 50 mA, maximum
2 V AC/DC / 1 mA, minimum
Approvals
CE
c
UL/CUL
GL
Applied for
Planned
4
Application Example
6
Operating Voltage Range
U
U
VCC
1,4
1,3
1,2
1,1
1
N
+ -
A
A1
A2
UN= 24 V DC / 24 V AC
CTL2
0,9
0,8
0,7
B
A
O
M
20 25 30 35 40 45 50 55 60 65
C]
T
[
°
CTL1
M
U
13
General Conditions
14
Direct alignment in the block, all devices 100% operating
factor, horizontal or vertical mounting.
Curve A
Maximum permissible continuous voltage Umax with limiting
continuous current on the contact side
5
Block Diagram
Curve B
A2
Minimum permissible relay operate voltage Uop following
pre-excitation
13
M
0
14
A1
2(CTL)
1(CTL)
PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany • Phone: +49 - 52 35 - 30 0
PHOENIX CONTACT • P.O.Box 4100 • Harrisburg • PA 17111-0100 • USA • Phone: +717-944-1300
www.phoenixcontact.com
101460_en_04
4
相关型号：
©2020 ICPDF网 联系我们和版权申明