TDA9991HL [PHILIPS]
Interface Circuit;![TDA9991HL](http://pdffile.icpdf.com/pdf2/p00257/img/icpdf/TDA9991HL_1554451_icpdf.jpg)
型号: | TDA9991HL |
厂家: | ![]() |
描述: | Interface Circuit CD 传感器 换能器 |
文件: | 总24页 (文件大小:120K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
INTEGRATED CIRCUITS
DATA SHEET
TDA9991HL
Vertical line driver and DC-DC
converter for Full Frame and
Frame Transfer CCD image
sensors
Preliminary specification
2001 May 29
Supersedes data of 2000 Dec 22
File under Integrated Circuits, IC02
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
FEATURES
The versatile programmable DC-DC converter generates
two positive voltages (VCAPNS and VCAPH) and the non
programmable DC-DC converter generates a negative
voltage (VVL) which is used internally. Voltage regulators
convert the DC-DC converter outputs into low-noise output
voltages (VNS, VSFD, VHFB and VSH). The required
voltages for the image sensor and the drivers can be
programmed via the serial bus with sufficient accuracy to
optimize the performance of the sensors. An on-board
reference voltage ensures stable output voltages over the
entire temperature range.
• Enables compact and cost effective camera design
• Eight two-level low-ohmic line drivers suitable for Philips
Full Frame (FF) and Frame Transfer (FT) CCD image
sensors
• Versatile programmable DC-DC converters and voltage
regulators to create all required low-noise supply
voltages for the Philips FT CCD sensor family and for
the on-chip drivers
• DC-DC converter can be operated with an on-chip free
running oscillator or with an external clock
An internal DCOK signal enables the vertical line drivers
when the DC-DC converter output voltages and the
regulator output voltages are at their required
• Wide supply range also suitable for direct use on
batteries
(programmable) level. When either VHFB, VCAPNS or VNS
drops below 80% of it’s programmed level, the DCOK
signal will become LOW. A signal on pin START (inverse
of DCOK signal) indicates that the device has started up
and is externally available.
• Electronic shutter driver (charge reset)
• Fast start-up
• DC ready signal available indicating the TDA9991HL
has started up
• 3-wire serial bus
The use of two external coils enables high efficiency of the
DC-DC converters and fast starting up. The maximum
current built-up in coil L2 can be set with an external
resistor RLIM optimizing the efficiency of the DC-DC
converter and making it independent of supply voltage
variations.
• Separate digital supply voltage for optimal interfacing
with DSP circuit and serial bus
• Low current consumption in Power-down mode.
APPLICATIONS
The DC-DC converter operates from an on-chip free
running oscillator or from an external clock signal.
• Digital still camera
• Desktop video camera
• Security camera
• Camcorder
The low impedance of the drivers enables fast transfer of
the image of the sensor. The drivers can switch between
0 V and VHFB (8 to 15 V). The eight vertical drivers (image
gate drivers) can be put into 3-state via the serial bus.
• DSP applications.
Charge reset of the CCD can be performed with a separate
electronic shutter driver.
GENERAL DESCRIPTION
When the TDA9991 is in Power-on mode, a HIGH level at
pin PWD will put the chip in Power-down mode. A LOW
level at pin PWD will enable Power-on mode again.
When pin PWD is left open-circuit, a pull-down resistor will
keep this input LOW.
The TDA9991HL forms the interface between the pulse
pattern generator and the CCD image sensor in camera
systems and minimizes the component count significantly
by integration of various functions. The device contains
eight vertical line drivers, a shutter driver for charge reset,
a versatile programmable DC-DC converter,
a non-programmable DC-DC converter and voltage
regulators which create all required low noise supply
voltages for FT and FF CCD sensors. A three wire serial
bus, similar to the ones used in the Philips front-end ICs
(TDA8786 and TDA8783) is used for programming the
device.
In the Power-down mode (set via the serial bus or through
pin PWD) the current consumption becomes virtually zero.
The serial bus is still available.
2001 May 29
2
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
QUICK REFERENCE DATA
SYMBOL
Supplies
PARAMETER
CONDITIONS
MIN.
TYP. MAX. UNIT
VDDA1
VDDA2
VDDD
analog supply voltage 1
analog supply voltage 2
digital supply voltage
3.6
−
−
−
7
V
V
V
3.6
2.6
7
3.6
Vertical line drivers
Ro(on)
HIGH- and LOW-level output
on-resistance
IL(H) = 200 mA; IL(L) = −200 mA −
0.66
16.5
−
−
Ω
Ω
Shutter driver
Ro(on)
HIGH- and LOW-level output
on-resistance
IL(H) = 3 mA; IL(L) = −3 mA
−
Output voltage regulators
VHFB
VNS
high output voltage
Nwell substrate output voltage
programmable
programmable
8
−
−
−
−
15
31
24
10
V
V
V
V
17
18
3
VSFD
VSH
source follower drain output voltage programmable
shutter driver output voltage programmable
Temperature range
Toper
operating temperature
−20
−
+70
°C
ORDERING INFORMATION
TYPE
PACKAGE
DESCRIPTION
NUMBER
NAME
VERSION
TDA9991HL
LQFP48
plastic low profile quad flat package; 48 leads; body 7 × 7 × 1.4 mm
SOT313-2
2001 May 29
3
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
BLOCK DIAGRAM
+V
+V
DDA
V
DDD
V
DDA1
DDD
AGND1
CAPBG
43
DGND
48
AGND3 HDA HDB AGND4
7
8
4
28
27
33
34
V
SH
BAND GAP
REFERENCE
VOLTAGE
SHUTTER
DRIVER
11
SHO
10
47
46
45
44
42
41
40
39
SHIN
VA1
VA2
VA3
VA4
VB1
VB2
VB3
VB4
VERTICAL LINE DRIVERS
30
29
26
25
31
32
35
36
A1
A2
A3
A4
B1
B2
B3
B4
LOGIC
CONTROL
AND
INTERFACE
1
3
SDATA
SCLK
SERIAL
INTERFACE
37
38
PWD
2
6
SEN
OSC
START
OSCILLATOR
V
SH
R
OSC
TDA9991HL
DCOK
V
15
DDA2
+V
23
22
20
21
DDA
SFD
NS
+
L2
L2
L1
17
14
DC-DC
CONVERTERS
VOLTAGE
REGULATORS
SH
+
−
VBE
L1
24
HFB
AGND2
16
9
13
VL
18
19
5
12
LIM
CAPNS CAPH
V5V
CAP12
MGT242
R
LIM
Fig.1 Block diagram.
4
2001 May 29
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
PINNING
SYMBOL PIN
DESCRIPTION
SYMBOL PIN
DESCRIPTION
serial bus data input
NS
22 Nwell substrate voltage output
SDATA
SEN
1
2
3
4
5
SFD
HFB
A4
23 source follower drain voltage output
24 horizontal voltage feedback output
25 A4 driver output
serial bus enable input
serial bus clock input
digital supply voltage
SCLK
VDDD
V5V
A3
26 A3 driver output
filter capacitor of digital supply
voltage
HDA
AGND3
A2
27 A drivers high voltage supply
28 A drivers analog ground 3
29 A2 driver output
OSC
6
external oscillator resistor or clock
input
A1
30 A1 driver output
AGND1
VDDA1
LIM
7
8
9
analog ground 1
B1
31 B1 driver output
analog supply voltage 1
peak current limiting resistor
B2
32 B2 driver output
HDB
AGND4
B3
33 B drivers high voltage supply
34 B drivers analog ground 4
35 B3 driver output
SHIN
SHO
CAP12
VL
10 electronic shutter driver input
11 electronic shutter driver output
12 filter capacitor of DC-DC converter
B4
36 B4 driver output
13 DC-DC converter negative low
voltage
PWD
START
VB4
VB3
VB2
VB1
CAPBG
VA4
VA3
VA2
VA1
DGND
37 power-down input
38 DC voltages ready output
39 B4 driver digital input
40 B3 driver digital input
41 B2 driver digital input
42 B1 driver digital input
43 filter capacitor of band gap reference
44 A4 driver digital input
45 A3 driver digital input
46 A2 driver digital input
47 A1 driver digital input
48 digital ground
L1
14 coil 1 connection
VDDA2
15 DC-DC converter analog supply
voltage 2
AGND2
L2
16 DC-DC converter analog ground 2
17 coil 2 connection
CAPNS
18 filter capacitor of DC-DC converter
CAPNS voltage
CAPH
19 filter capacitor of DC-DC converter
CAPH voltage output
SH
20 shutter voltage output
21 base voltage output
VBE
2001 May 29
5
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
1
2
36 B4
35
SDATA
SEN
B3
34 AGND4
33
SCLK
3
V
4
HDB
DDD
V5V
OSC
5
32 B2
31 B1
6
TDA9991HL
AGND1
7
A1
30
V
29 A2
8
DDA1
LIM
SHIN
9
AGND3
28
27 HDA
10
11
12
26
SHO
A3
CAP12
25 A4
MGT243
Fig.2 Pin configuration.
2001 May 29
6
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
FUNCTIONAL DESCRIPTION
The TDA9991HL can be separated into three main blocks
(see Fig.1):
handbook, halfpage
V
DDA
V
CAPNS
L2
• DC-DC converters
• Voltage regulators
• Drivers.
S2
V
CAPH
S1
The functionality of the blocks is described below.
DC-DC converters
The principle of the DC-DC converter with positive output
voltages VCAPNS and VCAPH is shown in Fig.3. The two
voltages are generated by charging coil L2 (closing S1)
and then discharging the charge built-up in coil L2 (by
opening S1) into the capacitor at pin CAPNS or, when S2
is closed, into the capacitor at pin CAPH. Since VCAPNS is
always higher than VCAPH, closing S2 will not cause a
discharge of the capacitor at pin CAPNS into the capacitor
at pin CAPH.
MGT244
Fig.3 Principle of DC-DC converter with positive
output voltage.
The current through switch S1 is being monitored and will
not exceed the maximum value set by an external resistor
at pin LIM. Limiting the maximum current will make the
charge built-up in coil L2 independent of the supply
voltage therefore keeping the converter efficiency
constant.
handbook, halfpage
V
DDA
S3
L1
V
VL
L1
MGT245
The principle of the DC-DC converter with the negative
output voltage VVL is shown in Fig.4. The negative voltage
is generated by charging coil L1 (closing S3) and then
discharging the charge built-up in coil L1 (by opening S3)
into the capacitor at pin VL. The capacitor at pin VL will be
charged to approximately −3 V; there is no current limiting.
Fig.4 Principle of DC-DC converter with negative
output voltage.
Voltage regulators
For an optimal performance of the CCD, the sensor
voltages VSH, VNS, VSFD and VHFB are being generated by
programmable voltage regulators with a very high ripple
rejection.
CAPNS,
CAPH
AMP1,
AMP2,
AMP3
The voltage regulators for VSH, VNS and VSFD all have the
same principle shown in Fig.5.
V
DAC
Peak currents are being supplied by the capacitor at the
output while the voltage regulator charges the capacitor
more slowly. The value of the capacitor determines the
output voltage drop when a peak current is being drawn.
SH,
NS,
SFD
V
V
V
=
= 1
= 1
SH
NS
SFD
MGT246
Fig.5 Principle of voltage regulators.
2001 May 29
7
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
The voltage regulator for the drivers supply (VHFB) can
operate in two modes, depending on the application it is
used in:
handbook, halfpage
CAPH
• Mode 1 at fast transport with high peak current
• Mode 2 at slow transport with constant current.
AMP4
V
DAC
VBE
C1
MODE 1
In applications where the transport of the image is done in
a very short period large currents (up to 1.5 A) are being
drawn which cannot be supplied by the voltage regulator
itself. In that event an external transistor is used to supply
the large peak currents (see Fig.6). Mode 1 is selected via
the serial interface (Latch 1, bit D1 = 0; see Table 3).
HFB
C2
V
= 8 to 15 V
HFB
R1
MGT247
Fig.6 Principle of voltage regulator of drivers
supply in mode 1.
In mode 1 the external transistor can supply large peak
currents which are being drawn from the capacitor used at
pin CAPH. Since VCAPH is chosen to be 2.6 or 5.15 V
(programmable via the serial bus with bit VD2X) above
VHFB the voltage at the capacitor at pin CAPH can drop
approximately 1.8 or 4.5 V during the transport without
affecting VHFB. This reduces the value (size) of the
capacitor required at pin CAPH. During the transport the
base-emitter voltage of the external transistor will increase
causing a drop on VHFB. The drop depends on the static
current set by R1 and the maximum peak current being
drawn and can be calculated with the following formula:
handbook, halfpage
MGT249
V
V
V
CAPH
HFB
Ipeak
Vdrop = 25 mV × Ln
-----------
IR1
t
transport
transport
The static current should be approximately 500 µA.
Capacitor C2, connected to the emitter, filters out the
spikes averaging the peak current. When the peak current
stops, the increased base-emitter voltage will drop back to
its normal level (see Fig.7).
Fig.7 Output voltage at pin CAPH during transport.
The base voltage VVBE might have been changed slightly
(tens of millivolts) but will get back to its desired level fast.
After transport the capacitor at pin CAPH will be charged
again by the DC-DC converter.
CAPH
MODE 2
AMP4
V
DAC
VBE
HFB
In applications where the transport of the image is slow, a
constant current is required which can be supplied by the
voltage regulator and no external transistor is needed.
Mode 2 is selected via the serial interface (bit D1 = 1).
V
= 8
HFB
C1
In mode 2, pins VBE and HFB must be tied together (see
Fig.8).
MGT248
In this mode the voltage regulator can supply currents up
to 30 mA. Peak currents need to be filtered out by
capacitor C1.
Fig.8 Principle of voltage regulator of drivers
supply in mode 2.
2001 May 29
8
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
START-UP CYCLE
During the start-up (pin START = HIGH and the internal
signal DCOK = LOW) the maximum output current of
AMP4 (see Fig.8) will be increased from 0.5 mA minimum
to 30 mA maximum. This is done to decrease the time
required to fully charge capacitor C1 during starting up.
MGT250
handbook, halfpage
V
START
H
When pin START = LOW (all voltages are at their required
level) or when VVBE is at its required level, the minimum
output current of AMP4 will automatically drop back to
0.5 mA. When mode 2 is selected the maximum output
current of AMP4 will remain 30 mA after starting up.
L
0%
80 ± 5%
100%
An integrated start-up cycle ensures a fast and safe
start-up of the TDA9991HL. The principle of the start-up
cycle (hysteresis) is shown in Fig.9. When starting up the
signal at pin START will be HIGH. When VCAPNS and
regulator output voltage
VCAPH are at 100% of their programmed level and VHFB
and VNS are above 80% of their programmed level,
pin START will become LOW. When VCAPNS, VHFB or VNS
drops below approximately 80% of their programmed level
the TDA9991HL will start again with the start-up cycle.
Fig.9 Hysteresis of start-up cycle.
When starting up, the capacitor at pin CAPNS will be
charged prior to the capacitor at pin CAPH. The capacitor
at pin VL is charged by a separate DC-DC converter
independent of the start-up cycle.
V
handbook, halfpage
HFB
HDA,
HDB
Vertical line drivers
For frame transport the TDA9991HL has eight two-level
low-ohmic drivers available. The principle of the driver
outputs is shown in Fig.10.
VA1 to VA4,
VB1 to VB4
A1 to A4,
B1 to B4
LOGIC
INTERFACE
A logic interface converts the digital input signal into the
two control signals for the driver transistors. It also
prevents both transistors to switch on at the same time.
During start-up the drivers are kept in 3-state.
3-STATE DCOK
MGT251
Table 1 A and B drivers; note 1
Fig.10 Principle of driver output.
LEVEL AT INPUT PINS
LEVEL AT OUTPUT PINS
LOW
HIGH
LOW
Shutter driver
HIGH
Table 2 Shutter driver output
Note
1. The internal DCOK signal will keep the A and B
outputs in 3-state until the output voltages of the
DC-DC converter and voltage regulators are at their
required level.
INPUT LEVEL AT
PIN SHIN
OUTPUT LEVEL AT
PIN SHO
LOW
HIGH
LOW
HIGH
2001 May 29
9
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
Serial interface
SDATA
SHIFT REGISTER
D0 D1 D2 D3 D4 A0 A1 A2
SCLK
SEN
LSB
MSB
5
LATCH
SELECTION
5
2
4
5
4
4
POWER ON/OFF,
3-STATE ON/OFF,
OSCILLATOR
FREE/EXTERNAL
(LATCH 0)
VD2X,
MODE
(LATCH 1)
V
V
V
V
HFB
NS
SFD
SH
(LATCH 2)
(LATCH 3)
(LATCH 4)
(LATCH 5)
on/off outputs oscillator
3-state
VD2X
4-bit DAC
5-bit DAC
4-bit DAC
4-bit DAC
mode
MGT252
Fig.11 Serial interface block diagram.
t
su(SDATA)
t
h(SDATA)
SDATA
SCLK
SEN
A2
A1
A0
D4
D3
D2
D1
D0
MGT253
t
t
h(SEN)
su(SEN)
Pin SEN must stay HIGH for at least two clock cycles after each word.
Fig.12 Loading sequence of input data to control DACs via the serial interface.
10
2001 May 29
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
Table 3 Serial interface programming (see Fig.11)
ADDRESS BITS
DATA BITS(1)
D2
LATCH
DESCRIPTION
A2
0
A1
A0
0
D4
D3
D1
D0
0
0
power-on, 3-state and clock selection
power-down (note 2)
power-on
0
1
0
1
outputs in normal operation
outputs in 3-state
don’t care
X
0
1
free running oscillator
external clock signal
fixed value
0
1
0
0
1
voltage drop and mode selection
2.7 V drop (bit VD2X = 0)
5.4 V drop (bit VD2X = 1)
mode 1
0
1
0
1
mode 2
2
3
4
5
0
0
1
1
1
1
0
0
0
1
0
1
4 bits of VHFB
X
X
X
0
:
0
:
0
:
0
:
output is 8 V
steps of approximately 467 mV
output is 15 V
1
1
1
1
5 bits of VNS
0
:
0
:
0
:
0
:
0
:
output is 17 V
steps of approximately 450 mV
output is 31 V
1
1
1
1
1
4 bits of VSFD
X
X
X
0
:
0
:
0
:
0
:
output is 18 V
steps of approximately 400 mV
output is 24 V
1
1
1
1
4 bits of VSH
X
X
X
0
:
0
:
0
:
0
:
output is 3 V
steps of approximately 467 mV
output is 10 V
1
1
1
1
Notes
1. X is a don’t care.
2. The Power-down mode also shuts down the DC-DC converter.
2001 May 29
11
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134).
SYMBOL
PARAMETER
analog supply voltage 1
CONDITIONS
MIN.
−0.3
MAX.
UNIT
VDDA1
VDDA2
VDDD
Vn
+7
+7
V
analog supply voltage 2
digital supply voltage
voltage at pins
−0.3
−0.3
V
V
+5.5
VA1 to VA4, VB1 to VB4, V5V, PWD,
SDATA, SEN, SCLK, SHIN and OSC
−0.3
VDDD + 0.3(1)
V
CAPBG
−0.3
−0.3
−0.3
−0.3
−0.3
−0.3
−6
V
V5V + 0.3
V
V
V
V
V
V
V
V
CAP12
+15
+20
+20
+45
+45
−
VBE, SH, HFB, HDA and HDB
CAPH
coil not connected
coil not connected
CAPNS
NS and SFD
VL
AGND1, AGND2, AGND3 and AGND4
VDGND − 0.3 VDGND + 0.3
In
current at pins
A1 to A4 and B1 to B4
static current
−100
0
+100
5
mA
mA
mA
mA
mA
VL
LIM
−3
0
SHO
START
−50
−3
+50
+0.2
Note
1. Maximum value of VDDD + 0.3 V but not higher than 5.5 V.
QUALITY SPECIFICATION
In accordance with “SNW-FQ-611E”.
CHARACTERISTICS
VDDA = 5 V; VDDD = 3.3 V; Tamb = 25 °C; inputs VA1 to VA4 and VB1 to VB4 are HIGH; VSHIN = 0 V; L1 = 47 µH;
L2 = 4.7 µH; RLIM = 680 Ω; VHFB = 12 V; VNS = 24 V; VSFD = 20 V; VSH = 8 V; VSTART = LOW; no load for regulator
output voltages; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supplies
VDDA1
analog supply voltage 1
analog supply current 1
3.6
5
7
V
IDDA1
VVA1 to VVA4 = VDDD
;
−
3.5
−
mA
VVB1 to VVB4 = VDDD
VSEN = 0
;
Iq(DDA1)
VDDA2
quiescent analog supply
current 1
Power-down mode;
latch 0 = 00X00; note 1
−
−
300
7
µA
analog supply voltage 2
3.6
5
V
2001 May 29
12
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
IDDA2
analog supply current 2
VVA1 to VVA4 = VDDD
;
;
−
−
130
−
mA
VVB1 to VVB4 = VDDD
SEN = 0; note 2
Power-down mode;
latch 0 = 00X00; note 1
V
Iq(DDA2)
quiescent analog supply
current 2
−
4
µA
VDDD
IDDD
digital supply voltage
digital supply current
2.6
3.3
3.6
V
VVA1 to VVA4 = VDDD
;
−
460
−
µA
VVB1 to VVB4 = VDDD
VSEN = 0
;
Iq(DDD)
quiescent digital supply
current
Power-down mode;
latch 0 = 00X00; note 1
−
−
100
µA
Vertical line drivers A and B
Ro(on)
HIGH- and LOW-level output IL(H) = 200 mA;
0.6
16
18
0.66
20
0.72
29
Ω
on-resistance
IL(L) = −200 mA
tr
tf
rise time of outputs
V
NS − VHFB > 7 V;
CL = 6.8 nF
NS − VHFB > 7 V;
ns
ns
fall time of outputs
V
23
29
CL = 6.8 nF
VOH
VOL
HIGH-level output voltage
LOW-level output voltage
−
VHFB
−
V
−
0
−
V
ILO(Z)
output leakage current in
3-state
3-state; VO < 6 V;
latch 0 = 00X11
−1
−
+1
µA
tPD
propagation delay
no load
40
ns
ns
∆tPD
propagation delay difference
between channels
−
−
3
Shutter driver (pin SHO)
Ro(on)
HIGH- and LOW-level output IL(H) = 3 mA;
−
16.5
−
Ω
on-resistance
IL(L) = −3 mA
VOH
VOL
tr
HIGH-level output voltage
LOW-level output voltage
rise time
−
−
−
VSH
0
−
−
V
V
V
NS − VSH > 7 V;
CL = 2 nF
NS − VSH > 7 V;
50
ns
tf
fall time
V
−
50
ns
CL = 2 nF
DC-DC converters
VCAPNS output voltage at pin CAPNS
VCAPH
−
VNS + 6
−
V
V
V
%
output voltage at pin CAPH bit VD2X = 0; note 3
bit VD2X = 1; note 3
VHFB + 2.45 VHFB + 2.6
VHFB + 2.75
VHFB + 4.9
VHFB + 5.15 VHFB + 5.4
∆IL2(max)
variation of maximum
note 4
−15
−
+15
current built-up in coil L2
tstart
start-up time of the DC-DC
converter
VSTART = HIGH;
RLIM = 680 Ω;
−
35
60
ms
VHFB = 13.1 V; note 5
2001 May 29
13
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Output voltage regulators
HIGH VOLTAGE FEEDBACK OUTPUT (PIN HFB)
VHFB
high voltage output
programmable (4 bits)
8
−
0
−
15
+5
0.5
V
∆VHFB
∆VHFB(T)
output voltage variation
−5
−
%
%
output voltage variation with Tamb = −20 to +70 °C
temperature
RR
ripple rejection
VSTART = LOW;
60
−
−
dB
f = 0 to 1 MHz; note 6
BASE VOLTAGE OUTPUT (PIN VBE)
IVBE
DC output current
VSTART = LOW; note 7
0.5
30
−
−
−
−
mA
mA
IVBE(start) output current during
start-up
VSTART = HIGH or in
mode 2; note 7
NWELL SUBSTRATE VOLTAGE OUTPUT (PIN NS)
VNS
output voltage
programmable (5 bits); 17
note 8
−
31
V
INS
DC output current
−
−
0
−
4
mA
%
∆VNS
∆VNS(T)
output voltage variation
−5
+5
0.5
output voltage variation with Tamb = −20 to +70 °C
−
%
temperature
RR
ripple rejection
VSTART = LOW;
50
−
−
dB
f = 0 to 1 MHz; note 6
SOURCE FOLLOWER DRAIN VOLTAGE OUTPUT (PIN SFD)
VSFD
output voltage
programmable (4 bits); 18
note 8
−
24
V
ISFD
DC output current
−
−
0
−
20
+5
0.5
mA
%
∆VSFD
∆VSFD(T)
output voltage variation
−5
output voltage variation with Tamb = −20 to +70 °C
−
%
temperature
RR
ripple rejection
VSTART = LOW;
50
−
−
dB
f = 0 to 1 MHz; note 6
SHUTTER DRIVER VOLTAGE OUTPUT (PIN SH)
VSH
output voltage
programmable (4 bits)
3
−
−
0
−
10
3
V
ISH
DC output current
output voltage variation
−
mA
%
∆VSH
∆VSH(T)
−5
−
+5
0.5
output voltage variation with Tamb = −20 to +70 °C
%
temperature
RR
ripple rejection
VSTART = LOW;
60
−
−
dB
f = 0 to 1 MHz; note 6
2001 May 29
14
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Oscillator
ffr
free running oscillator
frequency
latch 0 = 00X01;
ROSC = 47 kΩ; note 9
4
5.35
6.75
MHz
MHz
%
fclk
external clock input
frequency
latch 0 = 01X01; note 9
4
−
−
6.75
60
δ
duty factor external clock
input frequency
40
Serial interface (see Fig.12)
fSCLK(max) maximum clock frequency
VDDD = 3.6V
DDD = 3.3V
VDDD = 3.0V
DDD = 2.6V
−
−
−
−
−
−
−
−
−
4.0
3.3
2.5
1.8
−
MHz
MHz
MHz
MHz
s
V
V
tsu(SEN)
SEN set-up time
compared to SCLK
rising edge
0.16
------------------------
fSCLK(max)
tsu(SDATA) SDATA set-up time
compared to SCLK
rising edge
−
−
−
−
−
−
s
s
s
0.16
------------------------
fSCLK(max)
th(SEN)
SEN hold time
compared to SCLK
rising edge
0.08
------------------------
fSCLK(max)
th(SDATA)
SDATA hold time
compared to SCLK
rising edge
0.16
------------------------
fSCLK(max)
Control inputs
VIL LOW-level input voltage at
note 10
note 11
−0.2
−
−
0.3VDDD
V
V
pins SEN, SDATA, SCLK,
SHIN, PWD, VA1 to VA4,
VB1 to VB4 and OSC
VIH
HIGH-level input voltage at
pins SEN, SDATA, SCLK,
SHIN, PWD, VA1 to VA4,
VB1 to VB4 and OSC
0.7VDDD
5.5
Digital output (pin START)
VSTART(L) LOW-level output voltage
Isink(max) = 20 µA;
note 12
−
−
−
0.4
V
V
VSTART(H) HIGH-level output voltage
Isource(max) = 20 µA;
V
DDD − 0.4
−
note 13
Temperature range
Toper
operating temperature
−20
−
+70
°C
2001 May 29
15
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
Notes
1. A Power-on reset function puts the TDA9991HL in the Power-down mode when VDDD is supplied.
2. The supply current is measured without load (CCD) using the following programmed voltages:
VNS = 28 V; VSFD = 21 V; VHFB = 13 V; VSH = 8 V. The power consumption depends on the value of RLIM, the supply
voltages, programmed voltages and the efficiency of the DC-DC convertor under load condition. Therefore, the value
of IDDA2 in this table is a rough indication.
3. During transport VCAPH may drop to VHFB + 0.7 V (over the entire temperature range):
a) Bit VDX2 = 0: voltage drop is 1.8 V
b) Bit VDX2 = 1: voltage drop is 4.5 V.
1308
RLIM
4. IL2(max)
=
-------------
5. The charging time of the electrolytic capacitor at pin CAPNS is very small compared to the charging time of the
electrolytic capacitor at pin CAPH. The start-up time depends on:
a) Peak current IL2(max) chosen through coil L2; the maximum allowable peak current is 2.1 A
b) Value of the electrolytic capacitor at pin CAPH (470 µF)
c) Oscillator frequency
d) Required voltage level at pin CAPH.
6. Drivers not active.
7. During start-up (VSTART = HIGH) the maximum output current at pin HFB is increased to allow fast starting up.
8. VNS > VSFD
9. Pin OSC can be connected to an external clock or to an external resistor (in case the internal oscillator is used).
10. At VDDD = 2.6 V the maximum LOW-level voltage is 0.2VDDD
.
.
11. At VDDD = 2.6 V the minimum HIGH-level voltage is 0.8VDDD
12. VSTART will become LOW when:
.
a) All output voltages at pins HFB, NS and CAPNS are at 100% of their required (programmable) level
b) VCAPH = VHFB + 2.7 V (bit VD2X = 0) or VCAPH = VHFB + 5.4 V (bit VD2X = 1); VCAPH needs to have reached the
programmed voltage only once for VSTART to go LOW.
13. VSTART will become HIGH when either VHFB, VNS or VCAPNS drops below 80% (typical) of their programmed level.
2001 May 29
16
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
APPLICATION INFORMATION
drivers
control
start
100
nF
48 47 46 45 44 43 42 41 40 39 38 37
SDATA
SEN
B4
B4
B3
1
36
35
34
33
32
31
30
29
28
27
26
25
B3
serial
bus
2
SCLK
AGND4
HDB
B2
3
V
DDD
V
4
DDD
100 nF
V5V
OSC
B2
5
47 kΩ
B1
B1
6
PHILIPS
TDA9991HL
AGND1
A1
CCD(FT)
A1
7
V
DDA1
A2
V
A2
8
DDA
R
LIM
SHIN
AGND3
HDA
A3
9
LIM
shutter
control
10
11
12
SHO
A3
A4
100 nF
CAP12
A4
13 14 15 16 17 18 19 20 21 22 23 24
L1
L2
47
kΩ
(1)
BC868
V
V
DDA
DDA
10 µF
1 µF
(1)
27 kΩ
10 470
µF µF
47
µF
22
220
nF
100 220
µF
nF nF
330
nF
MGT254
L1 = 47 µH.
L2 = 4.7 µH.
RLIM = 680 Ω.
(1) The (emitter) current through the external resistor should be approximately 500 µA.
The value of the resistor can be adjusted depending on the emitter voltage (VHFB).
Fig.13 Application diagram.
2001 May 29
17
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
PACKAGE OUTLINE
LQFP48: plastic low profile quad flat package; 48 leads; body 7 x 7 x 1.4 mm
SOT313-2
c
y
X
36
25
A
E
37
24
Z
E
e
H
E
A
2
A
(A )
3
A
1
w M
p
θ
pin 1 index
b
L
p
L
13
48
detail X
1
12
Z
v M
D
A
e
w M
b
p
D
B
H
v
M
B
D
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
D
H
L
L
v
w
y
Z
Z
E
θ
1
2
3
p
E
p
D
max.
7o
0o
0.20 1.45
0.05 1.35
0.27 0.18 7.1
0.17 0.12 6.9
7.1
6.9
9.15 9.15
8.85 8.85
0.75
0.45
0.95 0.95
0.55 0.55
1.60
mm
0.25
0.5
1.0
0.2 0.12 0.1
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
EIAJ
99-12-27
00-01-19
SOT313-2
136E05
MS-026
2001 May 29
18
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
SOLDERING
If wave soldering is used the following conditions must be
observed for optimal results:
Introduction to soldering surface mount packages
• Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
• For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is
recommended.
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
Reflow soldering
The footprint must incorporate solder thieves at the
downstream end.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
• For packages with leads on four sides, the footprint must
be placed at a 45° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical reflow peak temperatures range from
215 to 250 °C. The top-surface temperature of the
packages should preferable be kept below 220 °C for
thick/large packages, and below 235 °C for small/thin
packages.
Typical dwell time is 4 seconds at 250 °C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Wave soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300 °C.
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320 °C.
To overcome these problems the double-wave soldering
method was specifically developed.
2001 May 29
19
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
Suitability of surface mount IC packages for wave and reflow soldering methods
SOLDERING METHOD
PACKAGE
WAVE
not suitable
REFLOW(1)
BGA, HBGA, LFBGA, SQFP, TFBGA
HBCC, HLQFP, HSQFP, HSOP, HTQFP, HTSSOP, HVQFN, SMS
PLCC(3), SO, SOJ
suitable
suitable
suitable
not suitable(2)
suitable
LQFP, QFP, TQFP
not recommended(3)(4) suitable
not recommended(5)
suitable
SSOP, TSSOP, VSO
Notes
1. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum
temperature (with respect to time) and body size of the package, there is a risk that internal or external package
cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the
Drypack information in the “Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods”.
2. These packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink
(at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version).
3. If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction.
The package footprint must incorporate solder thieves downstream and at the side corners.
4. Wave soldering is only suitable for LQFP, TQFP and QFP packages with a pitch (e) equal to or larger than 0.8 mm;
it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
5. Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is
definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
2001 May 29
20
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
DATA SHEET STATUS
PRODUCT
DATA SHEET STATUS(1)
DEFINITIONS
STATUS(2)
Objective data
Development This data sheet contains data from the objective specification for product
development. Philips Semiconductors reserves the right to change the
specification in any manner without notice.
Preliminary data
Product data
Qualification
This data sheet contains data from the preliminary specification.
Supplementary data will be published at a later date. Philips
Semiconductors reserves the right to change the specification without
notice, in order to improve the design and supply the best possible
product.
Production
This data sheet contains data from the product specification. Philips
Semiconductors reserves the right to make changes at any time in order
to improve the design, manufacturing and supply. Changes will be
communicated according to the Customer Product/Process Change
Notification (CPCN) procedure SNW-SQ-650A.
Notes
1. Please consult the most recently issued data sheet before initiating or completing a design.
2. The product status of the device(s) described in this data sheet may have changed since this data sheet was
published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.
DEFINITIONS
DISCLAIMERS
Short-form specification
The data in a short-form
Life support applications
These products are not
specification is extracted from a full data sheet with the
same type number and title. For detailed information see
the relevant data sheet or data handbook.
designed for use in life support appliances, devices, or
systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips
Semiconductors customers using or selling these products
for use in such applications do so at their own risk and
agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
Limiting values definition Limiting values given are in
accordance with the Absolute Maximum Rating System
(IEC 60134). Stress above one or more of the limiting
values may cause permanent damage to the device.
These are stress ratings only and operation of the device
at these or at any other conditions above those given in the
Characteristics sections of the specification is not implied.
Exposure to limiting values for extended periods may
affect device reliability.
Right to make changes
Philips Semiconductors
reserves the right to make changes, without notice, in the
products, including circuits, standard cells, and/or
software, described or contained herein in order to
improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for
the use of any of these products, conveys no licence or title
under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that
these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified.
Application information
Applications that are
described herein for any of these products are for
illustrative purposes only. Philips Semiconductors make
no representation or warranty that such applications will be
suitable for the specified use without further testing or
modification.
2001 May 29
21
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
NOTES
2001 May 29
22
Philips Semiconductors
Preliminary specification
Vertical line driver and DC-DC converter for Full Frame
and Frame Transfer CCD image sensors
TDA9991HL
NOTES
2001 May 29
23
Philips Semiconductors – a worldwide company
Argentina: see South America
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140,
Tel. +61 2 9704 8141, Fax. +61 2 9704 8139
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,
Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773
Pakistan: see Singapore
Belgium: see The Netherlands
Brazil: see South America
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 68 9211, Fax. +359 2 68 9102
Poland: Al.Jerozolimskie 195 B, 02-222 WARSAW,
Tel. +48 22 5710 000, Fax. +48 22 5710 001
Portugal: see Spain
Romania: see Italy
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381, Fax. +1 800 943 0087
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762,
Colombia: see South America
Czech Republic: see Austria
Tel. +65 350 2538, Fax. +65 251 6500
Slovakia: see Austria
Slovenia: see Italy
Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V,
Tel. +45 33 29 3333, Fax. +45 33 29 3905
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 58088 Newville 2114,
Tel. +27 11 471 5401, Fax. +27 11 471 5398
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615 800, Fax. +358 9 6158 0920
France: 7 - 9 Rue du Mont Valérien, BP317, 92156 SURESNES Cedex,
Tel. +33 1 4728 6600, Fax. +33 1 4728 6638
South America: Al. Vicente Pinzon, 173, 6th floor,
04547-130 SÃO PAULO, SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 821 2382
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 2353 60, Fax. +49 40 2353 6300
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 93 301 6312, Fax. +34 93 301 4107
Hungary: Philips Hungary Ltd., H-1119 Budapest, Fehervari ut 84/A,
Tel: +36 1 382 1700, Fax: +36 1 382 1800
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 5985 2000, Fax. +46 8 5985 2745
India: Philips INDIA Ltd, Band Box Building, 2nd floor,
254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025,
Tel. +91 22 493 8541, Fax. +91 22 493 0966
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2741 Fax. +41 1 488 3263
Indonesia: PT Philips Development Corporation, Semiconductors Division,
Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510,
Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080
Taiwan: Philips Semiconductors, 5F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2451, Fax. +886 2 2134 2874
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
60/14 MOO 11, Bangna Trad Road KM. 3, Bagna, BANGKOK 10260,
Tel. +66 2 361 7910, Fax. +66 2 398 3447
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053,
Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260 Umraniye,
TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007
ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813
Italy: PHILIPS SEMICONDUCTORS, Via Casati, 23 - 20052 MONZA (MI),
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
Tel. +39 039 203 6838, Fax +39 039 203 6800
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku,
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057
MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
Tel. +1 800 234 7381, Fax. +1 800 943 0087
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Uruguay: see South America
Vietnam: see Singapore
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 3341 299, Fax.+381 11 3342 553
Middle East: see Italy
For all other countries apply to: Philips Semiconductors,
Marketing Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN,
The Netherlands, Fax. +31 40 27 24825
Internet: http://www.semiconductors.philips.com
72
SCA
© Philips Electronics N.V. 2001
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
753504/03/pp24
Date of release: 2001 May 29
Document order number: 9397 750 08187
相关型号:
©2020 ICPDF网 联系我们和版权申明