PI3USB10LP-AZLE [PERICOM]
USB 2.0 High-Speed (480 Mbps) Signal Switch Targeted for Battery Powered Applications; 用于电池供电应用的USB 2.0高速( 480 Mbps)的信号开关![PI3USB10LP-AZLE](http://pdffile.icpdf.com/pdf1/p00134/img/icpdf/PI3US_743830_icpdf.jpg)
型号: | PI3USB10LP-AZLE |
厂家: | ![]() |
描述: | USB 2.0 High-Speed (480 Mbps) Signal Switch Targeted for Battery Powered Applications |
文件: | 总8页 (文件大小:553K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
PI3USB10LP-A
USB 2.0 High-Speed (480 Mbps) Signal Switch
Targeted for Battery Powered Applications
Features
Description
• USB 2.0 compliant (high speed and full speed)
ThePI3USB10LP-Aisasingledifferentialchannel2:1multiplexer/
demultiplexer USB 2.0 Switch. Industry leading advantages in-
clude a propagation delay of less than 250ps, resulting from its low
channel resistance and I/O capacitance. The device multiplexes
differential outputs from a USB Host device to one of two cor-
responding outputs. The switch is bidirectional and offers little
or no attenuation of the high-speed signals at the outputs. It is
designed for low bit-to-bit skew, high channel-to-channel noise
isolation and is compatible with various standards, such as High
Speed USB 2.0 (480 Mb/s).
• R is 5.5Ω typical @ V = 3.0V
ON
CC
• Low bit-to-bit skew
• Low Crosstalk: –40dB @ 500 Mbps
• Off Isolation: –35dB @ 500 Mbps
• Near-Zero propagation delay: 250ps
• Switching speed: 9ns
• Channel On Capacitance: 5.5pF
The PI3USB10LP-A offers overvoltage protection per the USB
2.0 specification. With the chip powered on or off, all I/O pins can
withstand a short to Vbus (5V +/-10%). This feature can only be
• V Operating Range: 2.7V to 4.2V ±10%
CC
• Data pin I/O ESD: 12kV HBM protection per JESD22-A114D
specification
offered if a 100-ohm pull up resistor is placed between V pin
CC
• 1,000 MHz Bandwidth
to the power supply.
• I/O pins have over-voltage protection and can tolerate a short
to Vbus
• Packaging (Pb-free & Green):
• 10-contact UQFN (ZM10) (1.4x1.8)
• 10-contact TQFN (ZL10) (1.3X1.6)
Application
• Routes signals for USB 2.0
• Hand-held devices
Pin Description (Top View)
Block Diagram
OE
D+
D-
D+A
D-A
D+B
D-B
10
8
5
9
4
D+A
D+B
7
6
D-A
D-B
1
SEL
2
3
Truth Table
OE
SEL
Function
H
X
I/O's = Hi-Z
L
L
L
D(+/-) to D(+/-)A
D(+/-) to D(+/-)B
H
PS8858G
05/02/07
1
07-0096
PI3USB10LP-A
USB 2.0 High-Speed (480 Mbps) Signal Switch
Targeted for Battery Powered Applications
Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
Note: Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device. This
is a stress rating only and functional operation of the device
at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Ex-
posure to absolute maximum rating conditions for extended
periods may affect reliability.
Storage Temperature ......................................................–65°C to +150°C
Supply Voltage to Ground Potential .................................–0.5V to +4.6V
DC Input Voltage ..................................................... –0.5V to V +0.5V
CC
DC Output Current ........................................................................120mA
Power Dissipation.............................................................................0.5W
DC Electrical Characteristics for USB 2.0 Switching over Operating Range
(T = –40°C to +85°C, V = 3.0 - 4.4V)
A
CC
(1)
(2)
Paramenter
Description
Test Conditions
Min.
1.8
Typ.
Max. Units
V
= 4.2V
= 3.3V
CC
CC
Guaranteed
HIGH level
V
Input HIGH Voltage
IH
V
1.6
V
V
Input LOW Voltage
Clamp Diode Voltage
Input HIGH Current
Input LOW Current
Guaranteed HIGH level
0.8
IL
IK
IH
V
V
V
V
V
= Max., I
= –18mA
-0.7
-1.2
CC
CC
CC
SEL
I
= Max., V
= Max., V
= VCC
= GND
±5
A
SEL
I
±5
IL
SEL
= Min., -0.4V ≤ V
= –40mA
≤ 1.0V
,
CC
input
input
input
(3)
R
ON
Switch On-Resistance
5.5
1.5
0.9
6.5
I
INPUT
V
= Min., -0.4V ≤ V
= -40mA
≤ 1.0V,
≤ 1.0V,
CC
(3)
R
On-Resistance Flatness
Ω
FLAT(ON)
I
INPUT
On-Resistance match from cen-
ter ports to any other port
V
= Min., -0.4V ≤ V
= -40mA
INPUT
CC
2.0
ΔR
ON
(3)
I
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. CC = 3.0 - 4.4V, TA = 25°C ambient and maximum loading.
V
3. Measured by the voltage drop between D and Dn pin at indicated current through the Switch On-Resistance is determined by the lower of the
voltages on the two (D, Dn) pins.
Power Supply Characteristics (V = 3.0 - 4.4V)
CC
(1)
Parameters
Description
Test Conditions
= Max., V = GND or V
CC
Min.
Typ.
Max.
Units
I
CC
Quiescent Power Supply Current
V
CC
1
μA
SEL
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
PS8858G
05/02/07
07-0096
2
PI3USB10LP-A
USB 2.0 High-Speed (480 Mbps) Signal Switch
Targeted for Battery Powered Applications
Capacitance (TA = 25°C, f = 1MHz)
(3)
(1)
(2)
Parameters
Description
Test Conditions
Typ.
Max.
Units
C
Input Capacitance
3.6
3.0
5.5
IN
C
Port I Capacitance, Switch OFF
Switch Capacitance, Switch ON
V
SEL
= 0V
pF
OFF
C
ON
Dynamic Electrical Characteristics Over the Operating Range
(2)
Parameters
Description
Test Conditions
Min.
Typ.
Max.
Units
X
Crosstalk
–40
–34
TALK
R = 50Ω, f = 250 MHz
dB
L
O
OFF Isolation
–3dB Bandwidth
–0.5dB Bandwidth
IRR
BW
BW
R = 50Ω
L
1,000
270
MHz
MHz
R = 50Ω
L
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading.
3. This parameter is determined by device characterization but is not production tested.
Switching Characteristics
Parameters
(1)
Description
Test Conditions
Min.
Typ.
Max. Units
(2,3)
t
Propagation Delay
0.25
PD
See Test Circuit for
Electrical Charac-
teristics
t
t
, t
Line Enable Time - SEL to D(+/-), D(+/-)n
Line Disable Time - SEL to D(+/-), D(+/-)n
0.5
0.5
15.0
9.0
ns
ps
PZH PZL
, t
PHZ PLZ
(2)
t
Output skew, channel-to-channel
3.5
7.5
14
20
C-C
SK
Output skew, bit-to-bit (opposite transition of the same
t
SKb-b
(2)
output (t
-t
)
PHL PLH
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Guaranteed by design.
3. The switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time
constant for the switch alone is of the order of 0.25ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical
driving signals, it adds very little propagational delay to the system. Propagational delay of the switch when used in a system is determined by
the driving circuit on the driving side of the switch and its interactions with the load on the driven side.
PS8858G
05/02/07
07-0096
3
PI3USB10LP-A
USB 2.0 High-Speed (480 Mbps) Signal Switch
Targeted for Battery Powered Applications
Test Circuit for Dynamic Electrical Characteristics
HP4396B
R1
T1
S1
PI3USB10LP-A
HP11667A
50-ohm
Test Circuit for Electrical Characteristics
6.0V
V
CC
200-ohm
10pF
V
IN
V
OUT
Pulse
Generator
D.U.T
200-ohm
R
T
C
L
Notes:
CL = Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse Generator
Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
All input impulses are supplied by generators having the following characteristics: PRR ≤ MHz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns.
The outputs are measured one at a time with on transition per measurement.
Switch Positions
Test
Switch
6.0V
t
, t
(output on I-side)
(output on I-side)
PLZ PZL
t
, t
GND
Open
PHZ PZH
Prop Delay
PS8858G
05/02/07
07-0096
4
PI3USB10LP-A
USB 2.0 High-Speed (480 Mbps) Signal Switch
Targeted for Battery Powered Applications
Switching Waveforms
2.5V
SEL
1.25V
1.25V
3.5V
1.5V
0V
V
2.5V
2.5V
Input
t
PZL
t
PLZ
Waveform 1
Waveform 2
OH
t
PLH
t
PHL
V
V
DD/2
DD/2
V
V
+0.3V
–0.3V
OL
V
V
OL
V
V
OH
t
t
PHZ
PZH
Output
2.5V
2.5V
OH
OH
OL
V
OL
Voltage Waveforms Propagation Delay Times
Voltage Waveforms Enable and Disable Times
Applications Information
Logic Inputs
The logic control inputs can be driven up to +3.6V regardless of the supply voltage. For example, given a +3.3V supply, the output
enables or select pins may be driven low to 0V and high to 3.6V. Driving IN Rail-to-Rail® minimizes power consumption.
Power Supply Sequencing
Proper power supplysequencing is recommended for all CMOS devices. Always apply VCC and GND before applying signals to
input/output or control pins.
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
PS8858G
05/02/07
07-0096
5
PI3USB10LP-A
USB 2.0 High-Speed (480 Mbps) Signal Switch
Targeted for Battery Powered Applications
Eye Diagram Measurements
-A
Figure 1: USB2.0 High-speed (480 Mbps) Signal Integrity Test Setup
Figure 2: USB 2.0 High Speed (480Mbps) TP1, left eye, and TP5, right eye, with PI3USB10LP-A in the signal path
PS8858G
05/02/07
07-0096
6
PI3USB10LP-A
USB 2.0 High-Speed (480 Mbps) Signal Switch
Targeted for Battery Powered Applications
BOTTOM VIEW
ꢃꢁꢊꢅꢄ%ꢃꢁꢃꢅ
ꢃꢁꢌꢃꢄꢍꢎꢏ
ꢖ
TOP VIEW
ꢗ
ꢃꢁꢋꢃꢄ%ꢃꢁꢀꢃ
ꢔꢃꢁꢀ
ꢃꢁꢓꢃꢄꢇꢈꢉ
ꢏꢝ ꢄꢀ
ꢞ ꢙꢘ$
ꢖ"ꢘꢛ
ꢆꢑ
ꢃꢁꢀꢅ
ꢃꢁꢀꢅ
ꢒ
ꢒ
ꢏꢝ ꢄꢀꢄ
ꢔ!" ꢘ"
ꢃꢁꢆꢃꢄ%ꢃꢁꢃꢅ
ꢃꢁꢃꢄꢄꢄꢄꢃꢁꢃꢅ
ꢀꢃꢑ
ꢆꢑ
ꢃꢁꢀꢃꢕ ꢔ ꢖ ꢗ
ꢀꢁꢂꢃꢄ%ꢃꢁꢃꢅ
ꢃꢁꢆꢅ
ꢜꢜ ꢃꢁꢀꢃ
ꢀꢃꢑ
ꢒ
ꢃꢁꢅꢃ
ꢃꢁꢊꢃ
ꢃꢁꢊꢅ
ꢃꢁꢆꢃꢄꢇꢈꢉ
ꢃꢁꢃꢓ
ꢒ
ꢀꢁꢂꢃ
ꢔ
ꢃꢁꢌꢃꢄꢍꢎꢏ
ꢀꢁꢐꢃ
ꢇꢘꢒ!ꢕꢕꢘ ꢙꢘꢙꢄꢚꢛ ꢙꢄꢏꢛ##ꢘ"
DATE: 03/20/06
.OTESꢀ
DESCRIPTION: 10-Contact, Thin Fine Pitch Quad Flat No-Lead (TQFN)
PACKAGE CODE: ZL (ZL10)
ꢀꢁ !LL DIMENSIONS ARE IN MILLIMETERS
ꢂꢁ 2EF *%$%#ꢃ -/ꢄꢂꢂꢅ
REVISION: A
DOCUMENT CONTROL #: PD-2052
PS8858G
05/02/07
07-0096
7
PI3USB10LP-A
USB 2.0 High-Speed (480 Mbps) Signal Switch
Targeted for Battery Powered Applications
4)1ꢀꢁ/ꢂ
Ordering Information
Ordering Code
Package Code
Package Description
Top Mark
AP
PI3USB10LP-AZLE
PI3USB10LP-AZME
ZL
Pb-free & Green, 10-contact TQFN
Pb-free & Green, 10-contact UQFN
ZM
AP
Notes:
• Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
• E = Pb-free and Green
• Adding X suffix = Tape/Reel
Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com
PS8858G
05/02/07
07-0096
8
相关型号:
![](http://pdffile.icpdf.com/pdf1/p00134/img/page/PI3US_743830_files/PI3US_743830_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00134/img/page/PI3US_743830_files/PI3US_743830_2.jpg)
PI3USB10LP-AZME
USB 2.0 High-Speed (480 Mbps) Signal Switch Targeted for Battery Powered Applications
PERICOM
![](http://pdffile.icpdf.com/pdfupload1/u00001/img/page/PI3USB10_509652_files/PI3USB10_509652_1.jpg)
![](http://pdffile.icpdf.com/pdfupload1/u00001/img/page/PI3USB10_509652_files/PI3USB10_509652_2.jpg)
PI3USB10MZEEX
Multiplexer And Demux/Decoder, USB Series, 1-Func, 2 Line Input, 4 Line Output, True Output, 3 X 3.50 MM, GREEN, TDFN-12
PERICOM
![](http://pdffile.icpdf.com/pdf2/p00308/img/page/PI3USB10MZKE_1854309_files/PI3USB10MZKE_1854309_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00308/img/page/PI3USB10MZKE_1854309_files/PI3USB10MZKE_1854309_2.jpg)
PI3USB10MZEEX
Multiplexer And Demux/Decoder, USB Series, 1-Func, 2 Line Input, 4 Line Output, True Output, 3 X 3.50 MM, GREEN, TDFN-12
DIODES
![](http://pdffile.icpdf.com/pdf2/p00284/img/page/PI3USB10MZKE_1692146_files/PI3USB10MZKE_1692146_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00284/img/page/PI3USB10MZKE_1692146_files/PI3USB10MZKE_1692146_2.jpg)
PI3USB10MZKEX
Multiplexer And Demux/Decoder, USB Series, 1-Func, 2 Line Input, 4 Line Output, True Output, 1.60 X 2.20 MM, GREEN, TQFN-12
PERICOM
![](http://pdffile.icpdf.com/pdf2/p00308/img/page/PI3USB10MZKE_1854309_files/PI3USB10MZKE_1854309_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00308/img/page/PI3USB10MZKE_1854309_files/PI3USB10MZKE_1854309_2.jpg)
PI3USB10MZKEX
Multiplexer And Demux/Decoder, USB Series, 1-Func, 2 Line Input, 4 Line Output, True Output, 1.60 X 2.20 MM, GREEN, TQFN-12
DIODES
©2020 ICPDF网 联系我们和版权申明