PI3CH200L [PERICOM]
Low Voltage, 5Ω, 2-Channel 2-Port NanoSwitch™; 低电压, 5Ω , 2通道2端口NanoSwitch ™型号: | PI3CH200L |
厂家: | PERICOM SEMICONDUCTOR CORPORATION |
描述: | Low Voltage, 5Ω, 2-Channel 2-Port NanoSwitch™ |
文件: | 总8页 (文件大小:636K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PI3CH200
Low Voltage, 5Ω, 2-Channel
2-Port NanoSwitch™
Features
Description
• Near-zero propagation delay
The PI3CH200 is a low voltage, 2-channel switch designed
with fast individual enables. The switch introduces no additional
propagation delay or additional ground bounce noise.
• 5Ω switches connect inputs to outputs
• High signal passing bandwidth (500 MHz)
• Beyond Rail-to-Rail switching
The PI3CH200 device has active LOW enables. It is very useful
in switching signals that have high bandwidth (500 MHz).
• 5V I/O tolerant with 3.3V supply in OFF and ON state
• 2.5V and 3.3V supply voltage operation
• Hot Insertion Capable
Applications
• High Bandwidth Data Switching
• Industrial Operating Temperature: –40ºC to +85ºC
• 2kV ESD Protection (human body model)
• Latch-up Performance: >250mA per JESD17
• Packaging (Pb-free & Green Available):
– 8-pin TSSOP (L)
• Hot-Docking
• Analog Signal Switching
• Differential Signal Switching
Pin Configuration
Block Diagram
B1
B2
A1
ꢆꢇꢇ
�ꢀꢈ
ꢃꢈ
�ꢀꢁ
ꢂꢁ
ꢁ
ꢈ
ꢉ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
EN
1
A2
ꢃꢁ
ꢂꢈ
ꢄꢀꢅ
EN2
Pin Description
(1)
Truth Table
Pin Name
Description
EN
A
B
V
CC
Function
Disconnect
Disconnect
Connect
x
x
x
EN
Switch Enable
A Ports
x
X
Hi-Z
Hi-Z
Bx
Hi-Z
Hi-Z
Ax
GND
A - A
2
1
H
V
V
CC
CC
B - B
2
B Ports
1
L
GND
Ground
Notes:
V
Power
CC
1. H = High Voltage Level, L = Low Voltage Level,
Hi-Z = High-Impedance
PS8721C
05/10/06
1
06-0246
PI3CH200
Low Voltage, 5Ω, 2-Channel
2-Port NanoSwitch™
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................................ –65°C to +150°C
Ambient Temperature with Power Applied ............... –40°C to +85°C
Supply Voltage to Ground Potential ........................... –0.5V to +4.6V
DC Input Voltage ........................................................ –0.5V to +6.0V
DC Output Current................................................................... 120mA
Power Dissipation....................................................................... 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these
or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect re-
liability.
DC Electrical Characteristics, 3.3V Supply (Over Operating Range, T = –40°C to +85°C, V = 3.3V ± 10%)
A
CC
(1)
(2)
Parameters
Description
Input HIGH Voltage
Input LOW Voltage
Clamp Diode Voltage
Input HIGH Current
Input LOW Current
High-Impedence Current
Test Conditions
Min.
Typ.
Max. Units
V
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
2
IH
V
–0.5
0.8
–1.8
±1
V
IL
IK
IH
V
V
V
V
= Min., I = –18mA
–1.3
CC
CC
CC
IN
I
= Max., V = V
IN CC
I
IL
= Max., V = GND
±1
µA
Ω
IN
CC
(3)
I
0 ≤ A, B ≤ V
±1
OZH
V
CC
= Min.,V = 0.0V
IN
4
5
6
8
(4)
I
= –48mA or –64mA
ON
R
Switch On-resistance
ON
V
CC
= Min., V = 3.6V, I = –15mA
IN ON
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined
by the lower of the voltages on the two (A,B) pins.
PS8721C
05/10/06
06-0246
2
PI3CH200
Low Voltage, 5Ω, 2-Channel
2-Port NanoSwitch™
DC Electrical Characteristics, 2.5V Supply (Over Operating Range, T = –40°C to +85°C, V = 2.5V ± 10%)
A
CC
(1)
(2)
Parameters
Description
Input HIGH Voltage
Inout LOW Voltage
Clamp Diode Voltage
Input HIGH Current
Input LOW Current
High Impedance Current
Test Conditions
Min. Typ.
Max.
V + 0.3
CC
Units
V
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
1.8
IH
V
–0.3
0.8
V
IL
IK
IH
V
V
V
V
= Max., I = –6mA
–0.7
–1.8
±1
CC
CC
CC
IN
I
= Max., V = V
IN CC
IIL
= Max., V = GND
±1
µA
Ω
IN
CC
(3)
I
0 ≤ A, B ≤ V
±1
OZH
V
= Min., V =0.0V,
CC
IN
6
7
8
I
= –48mA
ON
(4)
R
ON
Switch On Resistance
V
= Min., V = 2.25V,
CC
IN
14
I
= –15mA
ON
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined
by the lower of the voltages on the two (A,B) pins.
Capacitance (T = 25°C f = 1 MHz)
A
(1)
Parameters
Description
Test Conditions
Typ.
3.5
Units
C
IN
Input Capacitance
C
A/B Capacitance, Switch Off
A/B Capacitance, Switch On
V
= 0V
IN
3.5
pF
OFF
C
7.0
ON
Notes:
1. This parameter is determined by device characterization but is not production tested.
Power Supply Characteristics
(1)
(2)
Parameters
Description
Test Conditions
= 3.6V, V = GND or V
CC
Min. Typ.
Max.
Units
I
Quiescent Power Supply Current
V
0.8
mA
CC
CC
IN
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at VCC = 3.3V, +25°C ambient.
PS8721C
05/10/06
06-0246
3
PI3CH200
Low Voltage, 5Ω, 2-Channel
2-Port NanoSwitch™
Dynamic Electrical Characteristics Over the Operating Range (T = –40º to +85º, V = 3.3V ± 10%)
A
CC
Parameter
Description
Test Condition
See Test Diagram
See Test Diagram
See Test Diagram
Min.
Typ.
Max.
Units
dB
X
Crosstalk
–60
–60
500
TALK
O
Off-Isolation
–3dB Bandwidth
IRR
BW
200
MHz
Switching Characteristics over 3.3V Operating Range
Com.
Typ.
(1)
Parameters
Description
Conditions
Units
Min.
Max.
t
t
PLH
(2,3)
Propagation Delay
Ax to Bx, Bx to Ax
See Test Diagram
See Test Diagram
0.3
PHL
t
PZH
Enable Time ENx to Ax or Bx
Disable Time ENx to Ax or Bx
1.5
1.5
9.0
9.0
ns
t
PZL
t
PHZ
t
PLZ
Notes:
1. See test circuit and waveforms.
2. This parameter is guaranteed but not tested on Propagation Delays.
3. The switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load
capacitance. The time constant for the switch alone is of the order of 0.25ns for 10pF load. Since this time constant is much
smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational
delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its
interaction with the load on the driven side.
Switching Characteristics over 2.5V Operating Range
Com.
(1)
Parameters
Description
Conditions
Units
Min.
Max.
t
t
PLH
(2,3)
Propagation Delay
Ax to Bx, Bx to Ax
See Test Diagram
0.3
PHL
t
t
PZH
Enable Time ENx to Ax or Bx
Disable Time ENx to Ax or Bx
1.5
1.5
15.0
12.0
ns
PZL
See Test Diagram
t
PHZ
t
PLZ
Notes:
1. See test circuit and waveforms.
2. This parameter is guaranteed but not tested on Propagation Delays.
3. The switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load
capacitance. The time constant for the switch alone is of the order of 0.25ns for 10pF load. Since this time constant is much
smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational
delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its
interaction with the load on the driven side.
PS8721C
05/10/06
06-0246
4
PI3CH200
Low Voltage, 5Ω, 2-Channel
2-Port NanoSwitch™
Test Circuit for Electrical Characteristics
6.0V
V
CC
200Ω
V
IN
V
OUT
Pulse
Generator
D.U.T
10pF
L
200Ω
R
T
C
Notes:
•
•
•
•
•
•
CL = Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse Generator.
Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
All input impulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50-ohm, tR ≤ 2.5ns, tF ≤ 2.5ns.
The outputs are measured one at a time with one transition per measurement.
Switch Positions
Test
Switch
6.0V
t
, t
PLZ PZL
t
, t
GND
Open
PHZ PZH
Prop Delay
Test Circuit for Dynamic Electrical Characteristics
�ꢀꢁꢂꢃꢄꢅ
ꢆꢅ
ꢄꢅ
ꢇꢅ
�
ꢀꢀ
ꢁꢂꢃꢂꢄ
ꢈꢉꢅꢅꢊꢊꢋꢌ
ꢅꢎ�ꢀ
ꢍꢎ�
PS8721C
05/10/06
06-0246
5
PI3CH200
Low Voltage, 5Ω, 2-Channel
2-Port NanoSwitch™
Switching Waveforms
2.5V
ENx
1.25V
1.25V
0V
3.5V
1.5V
t
PZL
t
PLZ
V
Output
OH
OL
2.5V
2.5V
Input
V
DD/2
V
OL
+0.3V
V
t
PLH
t
PHL
t
PHZ
V
OH
t
PZH
V
OH
Output
2.5V
2.5V
V
V
-0.3V
OH
DD/2
V
OL
Output
V
OL
Voltage Waveforms Enable and Disable Times
3.5V
2.5V
Input
1.5V
t
t
PLH
PHL
V
OH
2.5V
Output
V
OL
t
= I t
t
PHL – PLH
I
SK(p)
Pulse Skew - t
SK(p)
PS8721C
05/10/06
06-0246
6
PI3CH200
Low Voltage, 5Ω, 2-Channel
2-Port NanoSwitch™
Applications Information
Logic Inputs
The logic control inputs can be driven upto 3.6V regardless of the supply voltage. For example, given a +3.3V supply, EN may be
®
driven LOW to 0V and HIGH to 3.6V. Driving EN Rail-to-Rail minimizes power consumption.
Power Supply-Sequencing
Proper power supply sequencing is recommended for all CMOS devices. Always apply V before applying signals to the input/
CC
output or control pins.
Hot Insertion
For Datacom and Telecom applications that have ten or more volts passing through the backplane, a high voltage from the power
supply may be seen at the device input pins during hot insertion. The PI3CHxx devices have maximum limits of 6V and 120mA for
20ns. If the power is higher or applied for a longer time or repeatedly reaches the maximum limits, the devices can be damaged.
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
Packaging Mechanical: 8-pin TSSOP (L)
�ꢇꢂꢜꢓꢀꢈꢆꢊꢂꢇꢈꢆꢃꢇꢛꢊꢈꢇꢝ
ꢅ�ꢊꢌꢊꢐꢒꢞꢋ
ꢃꢀꢟꢄꢁꢄꢇꢈꢉꢊꢊꢀ
�ꢘꢆꢀꢉꢊꢊꢐꢐꢠꢐꢡꢠꢞꢡ
Pericom Semiconductor Corporation
3545 N. 1st Street, San Jose, CA 95134
1-800-435-2335 • www.pericom.com
Note:
1. Package Outline Exclusive of Mold Flash and Metal Burr
2. Controlling dimentions in millimeters
3. Ref: JEDEC MO-153F/AA
�ꢀꢁꢂꢃꢄꢅꢆꢄꢇꢈꢉꢊꢋꢌꢅꢍꢎꢏꢊꢐꢑꢒꢌꢓꢍꢔꢊꢕꢍꢖꢗꢏꢊꢆꢁꢁꢇꢅ
ꢅꢘꢂꢙꢘꢚꢀꢊꢂꢇ�ꢀꢉꢊꢛꢊ
PS8721C
05/10/06
06-0246
7
PI3CH200
Low Voltage, 5Ω, 2-Channel
2-Port NanoSwitch™
Ordering Information
Ordering Code
PI3CH200L
Packaging Code
Package Description
L
L
173-mil, 8-pin TSSOP
Pb-free & Green, 173-mil, 8-pin TSSOP
PI3CH200LE
Notes:
•
•
Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
E = Pb-free & Green
• Adding an X suffix = Tape/Reel
Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com
PS8721C
05/10/06
06-0246
8
相关型号:
PI3CH200LX
Bus Driver, 3CH Series, 2-Func, 1-Bit, True Output, CMOS, PDSO8, 0.173 INCH, MO-153F/AA, TSSOP-8
PERICOM
PI3CH281
Low Voltage, High Bandwidth, 2-Channel, 4:1 Mux/DeMux, NanoSwitch with Single Enable
PERICOM
PI3CH281L
Low Voltage, High Bandwidth, 2-Channel, 4:1 Mux/DeMux, NanoSwitch with Single Enable
PERICOM
PI3CH281LE
Low Voltage, High Bandwidth, 2-Channel, 4:1 Mux/DeMux, NanoSwitch with Single Enable
PERICOM
PI3CH281LX
Multiplexer And Demux/Decoder, 3CH Series, 2-Func, 4 Line Input, 1 Line Output, True Output, CMOS, PDSO16, 0.173 INCH, PLASTIC, TSSOP-16
PERICOM
PI3CH281Q
Low Voltage, High Bandwidth, 2-Channel, 4:1 Mux/DeMux, NanoSwitch with Single Enable
PERICOM
PI3CH281QE
Low Voltage, High Bandwidth, 2-Channel, 4:1 Mux/DeMux, NanoSwitch with Single Enable
PERICOM
PI3CH281QE
Multiplexer And Demux/Decoder, 3CH Series, 2-Func, 4 Line Input, 1 Line Output, True Output, CMOS, PDSO16, 0.150 INCH, GREEN, PLASTIC, QSOP-16
DIODES
©2020 ICPDF网 联系我们和版权申明