AXM216101 [PANASONIC]
Board Connector, 16 Contact(s), 2 Row(s), Male, Straight, Solder Terminal, ROHS COMPLIANT;
| 型号： | AXM216101 |
| 厂家： | 
PANASONIC |
| 描述： | Board Connector, 16 Contact(s), 2 Row(s), Male, Straight, Solder Terminal, ROHS COMPLIANT 连接器 |
| 文件： | 总11页 (文件大小：399K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Discontinued as of September 30, 2010
MIL CONNECTORS
(AXM)
FOR PC BOARD
TO FLAT CABLE
FEATURES
1. High density mounting is possible.
Even with mounting right next to another
connector, insertion into and removal
from the socket can be done, providing a
saving in the surface mounting space.
3. Metal pin-less lever construction
Noise prevention is considered in this
construction by not using metal pins,
which, if present, act as noise absorbing
antennas.
4. Incorrect insertion prevention
mechanism.
Long lever type
Because of the box type construction of
the header and the special key that is
used, incorrect insertion can be
prevented.
Also, by means of the special key that is
used, incorrect insertion into an adjacent
connector is prevented.
2. Lever with original stopper
construction for great strength
The original stopper construction reduces
the possibility of lever damage even
when excess load is applied to the lever
during socket insertion and removal, and
during transportation.
Short lever type
Compliance with RoHS Directive
ORDERING INFORMATION
1. Socket
AXM
1
1
5
1: MIL connectors (Socket)
<No. of contacts (2 digits)>
10: 10 contacts 14: 14 contacts 16: 16 contacts 20: 20 contacts 26: 26 contacts 30: 30 contacts
34: 34 contacts 40: 40 contacts 50: 50 contacts 60: 60 contacts 64: 64 contacts
<Strain relief/Polarity guide>
0: Without strain relief/10 contacts: with polarity guide
2: Without strain relief/Min. 14 contacts with polarity guide, 10 contacts without polarity guide
4: With strain relief/14 contacts with polarity guide, 10 contacts without polarity guide
9: With strain relief/10 contacts: with polarity guide
<Pitch of flat cable>
1: 1.27 mm
<Surface treatment (Contact portion/Terminal portion)>
5: Au plating/Au plating
2. Header
AXM
2
1
2: MIL connectors (Header)
<No. of contacts (2 digits)>
10: 10 contacts 14: 14 contacts 16: 16 contacts 20: 20 contacts 26: 26 contacts 30: 30 contacts
34: 34 contacts 40: 40 contacts 50: 50 contacts 60: 60 contacts 64: 64 contacts
<Lever shape>
0: Long lever
1: Short lever
2: Without lever
<Terminal shape/Polarity slot>
0: Straight (Min. 14 contacts with polarity slot, 10 contacts without polarity slot)
1: Angle (Min. 14 contacts with polarity slot, 10 contacts without polarity slot)
8: Straight (10 contacts with polarity slot)
9: Angle (10 contacts with polarity slot)
<Surface treatment (Contact portion/Terminal portion)>
1: Au plating/Sn plating
panasonic-electric-works.net/ac
Discontinued as of September 30, 2010
AXM
3. Strain relief
AXM
3
3: MIL connectors (Strain relief)
<No. of contacts (2 digits)>
10: 10 contacts 14: 14 contacts 16: 16 contacts 20: 20 contacts 26: 26 contacts 30: 30 contacts
34: 34 contacts 40: 40 contacts 50: 50 contacts 60: 60 contacts 64: 64 contacts
SPECIFICATIONS
1. Characteristics
Item
Specifications
Conditions
1 A
When the header is connected to our wire-press socket,
the rated current varies depending on the wire used as
shown below.
Rated current
Electrical
(AWG#23/#24: 3 A, AWG#26: 2 A, AWG#28: 1 A)
characteristics
Breakdown voltage
Insulation resistance
750 V AC for 1 min.
Detection current: 1 mA
at 500V DC megger
Min. 1000MΩ
Measured based on the HP4338B measurement method
of JIS C 5402
Contact resistance
Unit removal force
Max. 20mΩ
Measured by steel-pin-gauge with (0.64 0.01)
Min. 0.785N {80gf}/2 contacts
× (0.64 0.01)mm2 cross section area.
Composite insertion force
Post holding force
Max. 2.94N {300gf} × no. of contacts
Mechanical
characteristics
Min. 19.6N {2kgf}
By pulling post until coming off
Sockets are pulled to the derection of shaft in the mated
condition
Lever locking strength
Cover strength
Min. 78.5N {8kgf}
Min. 78.5N {8kgf}
By pulling protector or strain relief to the direction of shaft
Lifetime
characteristics
Insertion and removal life
Ambient temperature
Vibration resistance
500 times
–55° to +105°C
No opening more than 1µsec. at max. 100mA carrying
current
Environmental
characteristics
10 to 55Hz at the double amplitude of 1.52mm
No opening more than 1µsec. at max. 100mA carrying
current
Shock resistance
490m/s2 {50G}
2. Materials and surface treatment
Part name
Material
Surface
—
Molded portion
Glass reinforced PBT (UL94V-0)
Contact portion: Ni plating on base, Au plating on surface
Pressured portion: Ni plating on base, Au plating on surface
Contact (Socket)
Post (Header)
Copper alloy
Copper alloy
Contact portion: Ni plating on base, Au plating on surface
Terminal portion: Ni plating on base, Sn plating on surface
3. Applicable cable
Standard wire
AWG28 Pitch 1.27mm
PRODUCT TYPES
1. Socket
2. Strain relief
No. of
polarity guide
Without strain relief
With strain relief
No. of contacts
Part No.
No. of contacts
10
0
1
1
1
1
1
1
1
1
1
1
1
AXM110215
AXM110015
AXM114215
AXM116215
AXM120215
AXM126215
AXM130215
AXM134215
AXM140215
AXM150215
AXM160215
AXM164215
AXM110415
AXM110915
AXM114415
AXM116415
AXM120415
AXM126415
AXM130415
AXM134415
AXM140415
AXM150415
AXM160415
AXM164415
10
14
16
20
26
30
34
40
50
60
64
AXM310
AXM314
AXM316
AXM320
AXM326
AXM330
AXM334
AXM340
AXM350
AXM360
AXM364
14
16
20
26
30
34
40
50
60
64
panasonic-electric-works.net/ac
Discontinued as of September 30, 2010
AXM
3. Header
Long lever type
Short lever type
No. of
polarity slot
Angle
Straight
Angle
Straight
No. of contacts
10
0
1
1
1
1
1
1
1
1
1
1
1
AXM210011
AXM210091
AXM214011
AXM216011
AXM220011
AXM226011
AXM230011
AXM234011
AXM240011
AXM250011
AXM260011
AXM264011
AXM210001
AXM210081
AXM214001
AXM216001
AXM220001
AXM226001
AXM230001
AXM234001
AXM240001
AXM250001
AXM260001
AXM264001
AXM210111
AXM210191
AXM214111
AXM216111
AXM220111
AXM226111
AXM230111
AXM234111
AXM240111
AXM250111
AXM260111
AXM264111
AXM210101
AXM210181
AXM214101
AXM216101
AXM220101
AXM226101
AXM230101
AXM234101
AXM240101
AXM250101
AXM260101
AXM264101
14
16
20
26
30
34
40
50
60
64
Notes) 1. A no-lever type is available. This product will be manufactured after receiving your order. Please inquire about delivery.
When ordering change the fourth digit in the part number to “2”.
2. The tray packing quantity for outer carton is 200 pcs.
3. For the available foreign standard products, refer to “STANDARDS CHART” on the end of the catalog.
4. Keys
Product name
Part No.
Polarity key
AXM8001
Incorrect insertion
prevention key
AXM8002
The CAD data of the products with a CAD Data mark can be downloaded from: http://panasonic-electric-works.net/ac
DIMENSIONS (Unit: mm)
• Socket
With strain relief
Without strain relief
Strain relief
A
6.0
15.9
14.3
14.0
10.5
A
6.0
Housing
Polarity guide
Protector
10.5
B
3.7
C
7.0
B
3.7
C
2.54 0.15
2.54 0.15
2.54 0.15
2.54 0.15
Dimension table (mm)
General tolerance: 0.3
No. of
No. of
Polarity slot
A
B
C
contacts
Cross section view
With strain relief
0
1
1
1
1
1
1
1
1
1
1
1
17.3
17.3
22.4
24.9
30.0
37.6
42.7
47.8
55.4
68.1
80.8
85.9
10.16
10.16
15.24
17.78
22.86
30.48
35.56
40.64
48.26
60.96
73.66
78.74
—
10
Without strain relief
14
16
20
26
30
34
40
50
60
64
0.8
1.0
1.4
4.35
panasonic-electric-works.net/ac
Discontinued as of September 30, 2010
AXM
• Header (Long lever type)
Terminal dimensions
Angle terminal
Straight terminal
CAD Data
F
C
2.54 0.15
3.59
26.4
6.5
13.9
3.0
17.3
3.0
ꢀ0.5 0.05
ꢀ0.5 0.05
2.85
2-2.6 dia.
2.54 0.15
2.54 0.15
Recommended PC board pattern
(BOTTOM VIEW)
Angle terminal
E
B
A
3.95
8.4
8.7
0.80+0.1 dia.
0
2-2.6 dia.
D
(17.3)
(13.9)
0.74
General tolerance: 0.3
Dimension table (mm)
2.85
2-3.2 dia.
(M3 screws)
2.54 0.05
2.54 0.05
E 0.1
B 0.1
(A)
No. of contacts
No. of Polarity slot
A
B
C
D
E
F
0
1
1
1
1
1
1
1
1
1
1
1
32.0
32.0
37.1
39.6
44.7
52.3
57.4
62.5
70.1
82.8
95.5
100.6
21.84
21.84
26.92
29.46
34.54
42.16
47.24
52.32
59.94
72.64
85.34
90.42
17.53
17.53
22.61
25.15
30.23
37.85
42.93
48.01
55.63
68.33
81.03
86.11
27.9
27.9
33.0
35.6
40.6
48.3
53.34
58.4
66.0
78.7
91.4
96.5
10.16
10.16
15.24
17.78
22.86
30.48
35.56
40.64
48.26
60.96
73.66
78.74
38.6
38.6
43.7
46.2
51.3
58.9
64.0
69.1
76.7
89.4
102.1
107.2
10
14
16
20
26
30
34
40
50
60
64
Straight terminal
2-3.2 dia.
(M3 screws)
0.80+0.1 dia.
0
1.52
(8.7)
(8.4)
3.95
2.54 0.05
2.54 0.05
E 0.1
D 0.1
(A)
Note) Dimensions of A, B, D and E are the same as the
header dimensions.
• Header [Short lever]
CAD Data
Terminal dimensions
Angle terminal
Straight terminal
F
C
2.54 0.15
3.59
22.6
6.5
13.9
17.3
3.0
3.0
2.85
2-2.6 dia.
ꢀ0.5 0.05
ꢀ0.5 0.05
2.54 0.15
2.54 0.15
E
B
A
Recommended PC board pattern
(BOTTOM VIEW)
Angle terminal
3.95
8.4
8.7
0.80+0.1 dia.
0
2-2.6 dia.
(17.3)
(13.9)
D
0.74
General tolerance: 0.3
Dimension table (mm)
2.85
2-3.2 dia.
2.54 0.05
No. of contacts
No. of Polarity slot
A
B
C
D
E
F
2.54 0.05
E 0.1
B 0.1
(A)
(M3 screws)
0
1
1
1
1
1
1
1
1
1
1
1
32.0
32.0
37.1
39.6
44.7
52.3
57.4
62.5
70.1
82.8
95.5
100.6
21.84
21.84
26.92
29.46
34.54
42.16
47.24
52.32
59.94
72.64
85.34
90.42
17.53
17.53
22.61
25.15
30.23
37.85
42.93
48.01
55.63
68.33
81.03
86.11
27.9
27.9
33.0
35.6
40.6
48.3
53.34
58.4
66.0
78.7
91.4
96.5
10.16
10.16
15.24
17.78
22.86
30.48
35.56
40.64
48.26
60.96
73.66
78.74
35.0
35.0
40.1
42.7
47.7
55.4
60.4
65.5
73.1
85.8
98.5
103.6
10
14
16
20
26
30
34
40
50
60
64
Straight terminal
2-3.2 dia.
(M3 screws)
0.80+0.1 dia.
0
1.52
(8.7)
(8.4)
3.95
2.54 0.05
2.54 0.05
E 0.1
D 0.1
(A)
Note) Dimensions of A, B, D and E are the same as the
header dimensions.
panasonic-electric-works.net/ac
Discontinued as of September 30, 2010
AXM
CABLE NO. AND TERMINAL POSITION CORRELATION DRAWING
Socket
Header (Angle terminal)
Terminal numbers are not indicated on
the connector. Using the triangle mark as
reference, the connection operations and
printed circuit board design should be
carried out.
Triangle mark
Triangle mark
When the cable numbers are temporarily
assigned from the end as 1, 2, 3, 4 ... n,
the corresponding terminal number
positions for the socket are as shown in
the drawing on the left. The header
terminal positions and corresponding
positions are shown in the drawing on the
left.
Triangle mark
n
n-1
2
3 1
n-1
1
3
Header (Straight terminal)
n
4 2
2
4
n
Cable
1 23 4
n
Cable No.
n-1
3 1 Triangle mark
COMBINATION OF HEADER AND SOCKET
With strain relief
Without strain relief
Header
Long lever
type
Short lever
type
Socket
Strain relief
Good
Not good
Without strain
relief
Not good
Good
Long lever type
Short lever type
REGARDING REVERSE AND INCORRECT INSERTION PREVENTION
1. Reverse insertion prevention
mechanism
2. Polarity key (AXM8001) for double
prevention of reverse insertion
Reverse insertion is doubly prevented by
inserting the polarity key (AXM8001) into
the header to create a projection and by
aligning this projection with the cutout in
the socket.
3. Incorrect insertion prevention key
(AXM8002) ideal for preventing
incorrect insertion into adjacent
connectors when a miltiple number of
MIL connectors with the same number
of contacts are used
Incorrect insertion is prevented by
plugging the hole in the socket with the
incorrect insertion prevention key
(AXM8002) and then by removing or
cutting off the pin of the corresponding
header.
The header polarity slot and socket
polarity guide of these MIL connectors
make for a construction which prevents
reverse insertion. (However, the 10-
contact type does not feature this
construction.)
Socket
Incorrect insertion
prevention key
Cutout
Plarity key
Projection
Polarity guide
Hand-held part
(break off after insertion)
Hand-held part
(break off
Polarity key
now in place
after insertion)
Polarity slot
Header
Remove corresponding pin
panasonic-electric-works.net/ac
Discontinued as of September 30, 2010
AXM
NOTES
1. Regarding design of printed circuit
board
4. Regarding soldering of the header
Soldering should be carried out under the
conditions given below.
7. Regarding the selection of header
type
When making the selection of the header,
the following factors should be used for
the selection.
The connector terminal numbers are not
indicated. Using the triangle mark as
reference, the printed circuit board
design and the cable connection
operations can be carried out.
2. Regarding insertion into and
removal from the socket
When inserting or removing the
connector, be careful not to pull the
cable. Hold the socket by hand to remove
the connector when the no-lever type is
used.With the lever type header, removal
is easy.
260°C: Within 10 seconds
300°C: Within 5 seconds
350°C: Within 3 seconds
Condition
Repeated Occasional
Forceused
5. Regarding the handling of header
terminals
vibration
vibration
on cable
and shock and shock
Very good Very good Very good
Good Good Not good
Header
Care should be taken with the header
terminals because repeated bending of
the terminals can lead to damage.
6. Regarding the cable pressure
connection tool
The special tool provided by our
company for cutting the cable and
making the pressure connections should
be used.
Long lever
type
Short lever
type
Note) Vibration: 9.8 m/s2 {1G}/10 to 150 Hz
Shock: 49 m/s2 {5G}
The above should be considered as criteria.
When the socket is unconnected, be
careful not to apply excessive force to the
levers.
For other details, please verify with the
product specification sheets.
3. Regarding external force applied to
the cable
When there is the possibility that external
force may be applied to the cable, or in
the case of vibration being applied to the
connector cable, a strain relief socket
should be used.
panasonic-electric-works.net/ac
Discontinued as of September 30, 2010
AXY
FLAT CABLE CONNECTOR
TOOLS (AXY)
TOOLS FOR
FLAT CABLE CONNECTOR
CABLE CUTTER
FEATURES
NOTES
1. Flat cable (from 10 to 64 contacts) can
be cut.
1. Setting of flat cable
First, set the guide plate at the correct
width. Then fix the cable and cut it.
2. Exchange of cutting knife
Push to attach the knife to the stopper pin
of cutter holder and then set it.
3. Safety cover
Cutting work should be done with safety
cover set. Please do not put your hand
inside of safety cover set.
2. Accurate cutting only by setting cable
to the guide.
3. Cutting knife can be fixed by clamper
from the side and exchanged easily.
4. Safety cover for cutting knife is
equipment.
5. The replacement blade of a
commercially available box cutter can be
used as the cable cutter blade.
4. Do not remodel this product or use
it for other purposes.
(mm)
Compliance with RoHS Directive
PRESSURE WELDING UNIT
PRODUCT TYPES
Product name
Cable cutter
Part No.
AXY80000
FEATURES
1. Operation without worry of
connecters becoming damaged
When pressure welding, the connector
will not break even if pressed too hard
because the guide plate acts as a
stopper.
4. Pressure welding of 10 to 64 strand
cable is easily accomplished by
changing the position of the guide
plate.
5. Positioning of the connector and
cable is easily accomplished with the
guide plate.
Pressing plate
2. Easy operation
Guid plates
Handle
Designed with the operator in mind,
pressure welding is sure and easy with
minimal force needed when operating the
lever. It is also well suited to repetitive
operation.
3. Using the same unit, all types of
connectors can be pressure welded
by simply replacing center locator and
guide plate.
6. After pressure welding a flat cable,
the connector can be easily removed
by pressing the handle to pop it out.
7. Even if the connector type changes,
the cover is always face down and
pressure welding is always possible.
Cables will never be displaced during
pressure welding.
Center locator
Attachment
AXY10000
Compliance with RoHS Directive
PRODUCT TYPES
Products name
Pressure welding unit
Attachment
Part No.
Remarks
AXY10000
AXY20101
AXY20201
AXY20202
AXY20203
AXY20205
AXY20301
AXY20302
AXY20303
AXY20305
AXY20401
AXY20404
AXY20405
AXY20406
MIL and PCB types, Cable pitch 1.27mm
MIL type
PCB Mini-dip type
Center locator
PCB IC type, Terminal row pitch 7.62mm
PCB IC type, Terminal row pitch 15.24mm
MIL type
Accessories
Guide plate
PCB Mini-dip type
PCB IC type, Terminal row pitch 7.62mm
PCB IC type, Terminal row pitch 15.24mm
Mini-dip type, Terminal row pitch 2.54mm, 30 to 64 contacts
IC type, Terminal row pitch 15.24mm, 24 to 40 contacts
Mini-dip type, Terminal row pitch 2.54mm, 10 to 26 contacts
IC type, Terminal row pitch 7.62mm, 14 to 20 contacts
Spacer
Note) The pressure welding unit is not include the accessories.
panasonic-electric-works.net/ac
Discontinued as of September 30, 2010
AXY
COMBINATION OF ACCESSORIES
Applicable socket
No. of contacts
Every type
10 to 26
Attachment
Center locator
AXY20201
Guide plate
AXY20301
Spacer
—
MIL type
AXY20405
AXY20401
AXY20406
AXY20404
PCB (Mini-dip type)
PCB (IC type)
AXY20202
AXY20302
30 to 64
AXY20101
14 to 20
AXY20203
AXY20205
AXY20303
AXY20305
24 to 40
SAFETY NOTES
1. Do not do the following dangerous
actions when using the pressure
welder.
2. Secure the pressure welder to the
work bench to prevent it from falling
over. Also, do not apply excessive
force to the lever when pressure
welding (such as by applying the full
weight of your body).
• Insert hand or fingers beneath the
pressure plate when operating the lever.
• Allow your fingers to get close to
moving parts when operating the lever.
• Let go of the lever when in progress
after pressure welding a connector.
(Be sure to keep your hand on the lever
all the way to the end.
Otherwise the lever might snap back
with considerable force.)
PRESSING PLATE OF PRESSURE WELDING UNIT
1. The pressing plate consists of the
pressing plate main unit and MIL/PCB
type connector plate.
When pressure-welding MIL/PCB type connectors
2. Proceed with the pressure connection
of MIL type connectors (AXM1 series)
and PCB type connectors (AXP series)
with the MIL/PCB connector plate
attached to the pressing plate main unit.
Use the hexagonal head bolt to mount
and remove the MIL/PCB type connector
plate.
Pressing plate main unit
Hexagonal head bolt
Resin panel
MIL/PCB type connector plate
DIMENSIONS (Unit: mm)
• Pressure welding unit
130
Handle
400
Pressing plate
Location for attachment
310
150
• Accessories
18
130
Spacer
130
Attachment
Center locator
Guide plate
Spacer
Center locator
Guide plate
Attachment
Handle
panasonic-electric-works.net/ac
Discontinued as of September 30, 2010
AXY
NOTES
1. Sockets setting
3. Pressure connection
4. Strain relief
After covers are temporary fixed with
housing (or base), sockets are set at the
gutter of center locator. (See Fig. 1)
2. Method of inserting flat cable
The guide plate is set at the correct figure
of scale, corresponding to the number of
contacts (cable width). Then cable is
inserted along with the guide until it
reaches at the stopper. (See Fig. 2)
After adjusting the lower limit of the
pressing plate, the connectors should be
pressed. Since the guide plate is the
stopper, the connectors should be
pressed until contacting the pressing
plate to the guide plate.
In case of PCB types, however, spacers
should be placed over the base.
(See Fig. 2)
Regarding MIL type, strain relief should
be fixed manually after pressure
connection of cables. (See Fig. 3)
5. Be sure to use our pressure welding
unit and its accessories when
conducting pressure welding.
CABLE PRESSURE WELDING
MIL type
Housing (or base)
Pressing plate
Pressing plate
Guide plate
Protector (or cover)
Center locator
Flat cable
Center locator
MIL type
PCB type
PCB type
Fig. 3 Set condition of strain relief
Pressing
plate
Pressing plate
Protector Center locator
Cover
Fig. 1 Socket set condition
Spacer
Fig. 2 Pressure welding condition
SAFETY NOTES FOR SPECIALIZED TOOLS
1. Cable Cutter
2. Pressure Welding Unit
1) Never remove the safety cover
2) Never insert your finger inside the
safety cover
3) Use on a stable surface
4) Do not alter this product, or use it for
other purposes
1) Do not place fingers beneath the
pressurized plate or in or near moving
parts, while the lever is being operated.
2) Lock the unit in place on a
workbench or the like.
3) Do not alter this product, or use it for
other purposes
panasonic-electric-works.net/ac
Discontinued as of September 30, 2010
HARNESS FABRICATION FOR FLAT CABLE CONNECTOR
NOTES WHEN FABRICATING HARNESSES
1. Common items
For our product, the following cable length is necessary. (For each side)
1) Select the appropriate connector and
cable according to the conditions of use.
2) It is recommended that our cable
cutter and pressure welding unit be used.
3) After making the pressure welding, the
condition of the connection should be
confirmed.
Without strain relief
With strain relief
6mm
MIL type socket
15mm
7mm
Mini-dip type
PCB type connector
IC type 14 to 20 contacts
IC type 24 and 40 contacts
10mm
20mm
3. Cable pressure welding
4) Because there are standard terminal
layout and reverse terminal layout for
PCB type connectors, the connector
suitable for the use should be selected.
2. Cable cutter
1) Bring the cable end surface in line with
the connector end surface, and set in the
groove of the cable guide of the protector.
2) When making a cable pressure
welding for a PCB type connector, it is
recommended that a spacer be used.
This can prevent breakage of the
terminals.
1) The cable should be cut at right angles
to the corresponding length.
2) Use a sharp cutter for making the cut.
3) When setting the cable length, the
pressure welding portion and strain relief
coil should be considered and set
accordingly.
Example 1: MIL type and MIL type
Cable mark
Cable mark
Example 2: PCB type and PCB type
Standard terminal layout
Reverse terminal layout
Cable mark
Cable mark
Cable mark
Cable mark
Example 3: PCB type and MIL type
Standard terminal layout
Reverse terminal layout
Cable mark
Cable mark
Cable mark
Cable mark
panasonic-electric-works.net/ac
Discontinued as of September 30, 2010
AXH
HARNESS ASSEMBLY ORDERING INFORMATION
Number of
contacts for
connector
cable
Left connector type
Cable type and length
Right connector type
AXH
AXH connector harness designation
Number of contacts for connector or cable
Left connector type (see Note 1)
Connection of connector and cable (see Note 2)
Cable types
Standard type: Stranded AWG 28: 1
Fluted type:
Stranded AWG 28: 2
Cable mark
Front:
Rear:
1
2
Not specified: 3
Cable length (3 digits)
Example: 020 for 20 cm (Only 5 cm and longer available.)
Right connector type (see Note 1)
Connection of connector and cable (see Note 2)
Note 1) Connector type
Connector
Type
Without strain relief
Order No.
M12
MIL type connector
With strain relief
M14
Srandard terminal layout
Reverse terminal layout
Reverse terminal layout
P42
Mini-dip type
IC type
PCB type connector
P46
P56
Note 2) Connection of connector and cable
Order No.
1
2
3
4
5
6
7
8
Left connector
Right connector
Cable mounting
Strain relief
Upper side
Lower side
Upper side
Lower side
Without strain relief
With strain relief
We slso accept orders for harnessed products. Call for more information.
panasonic-electric-works.net/ac
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明