PMS171B-M10 [PADAUK]
8bit OTP MCU with 8-bit ADC;型号: | PMS171B-M10 |
厂家: | PADAUK Technology |
描述: | 8bit OTP MCU with 8-bit ADC |
文件: | 总92页 (文件大小:2171K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PMS171B
8bit OTP MCU with 8-bit ADC
Datasheet
Version 1.03 – Sep. 2, 2020
Copyright 2020 by PADAUK Technology Co., Ltd., all rights reserved
6F-6, No.1, Sec. 3, Gongdao 5th Rd., Hsinchu City 30069, Taiwan, R.O.C.
TEL: 886-3-572-8688 www.padauk.com.tw
PMS171B
8bit OTP MCU with 8-bit ADC
IMPORTANT NOTICE
PADAUK Technology reserves the right to make changes to its products or to terminate
production of its products at any time without notice. Customers are strongly
recommended to contact PADAUK Technology for the latest information and verify
whether the information is correct and complete before placing orders.
PADAUK Technology products are not warranted to be suitable for use in life-support
applications or other critical applications. PADAUK Technology assumes no liability for
such applications. Critical applications include, but are not limited to, those which may
involve potential risks of death, personal injury, fire or severe property damage.
PADAUK Technology assumes no responsibility for any issue caused by a customer’s
product design. Customers should design and verify their products within the ranges
guaranteed by PADAUK Technology. In order to minimize the risks in customers’ products,
customers should design a product with adequate operating safeguards.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 2 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Table of content
1. Features.................................................................................................................................8
1.1.
1.2.
1.3.
1.4.
Special Features.....................................................................................................................8
System Features.....................................................................................................................8
CPU Features.........................................................................................................................8
Package Information ...............................................................................................................8
2. General Description and Block Diagram............................................................................9
3. Pin Definition and Functional Description .......................................................................10
4. Device Characteristics.......................................................................................................16
4.1.
4.2.
4.3.
4.4.
4.5.
4.6.
4.7.
4.8.
4.9.
AC/DC Device Characteristics ..............................................................................................16
Absolute Maximum Ratings...................................................................................................18
Typical ILRC frequency vs. VDD...........................................................................................18
Typical IHRC frequency deviation vs. VDD (calibrated to 16MHz).........................................19
Typical ILRC Frequency vs. Temperature.............................................................................19
Typical IHRC Frequency vs. Temperature (calibrated to 16MHz)..........................................20
Typical operating current vs. VDD @ system clock = ILRC/n................................................20
Typical operating current vs. VDD @ system clock = IHRC/n ...............................................21
Typical operating current vs. VDD @ system clock = 4MHz EOSC / n..................................21
4.10. Typical operating current vs. VDD @ system clock = 32KHz EOSC / n.................................22
4.11. Typical operating current vs. VDD @ system clock = 1MHz EOSC / n..................................22
4.12. Typical IO driving current (IOH) and sink current (IOL) .............................................................23
4.13. Typical IO input high/low threshold voltage (VIH/VIL) ..............................................................25
4.14. Typical resistance of IO pull high device ...............................................................................25
4.15. Typical resistance of IO pull Low device................................................................................26
4.16. Typical power down current (IPD) and power save current (IPS)..............................................27
5. Functional Description.......................................................................................................28
5.1.
5.2.
Program Memory - OTP........................................................................................................28
Boot Procedure.....................................................................................................................28
5.2.1. Timing charts for reset conditions.................................................................................29
Data Memory - SRAM...........................................................................................................30
Oscillator and clock...............................................................................................................30
5.4.1. Internal High RC oscillator and Internal Low RC oscillator.........................................30
5.4.2. Chip calibration..........................................................................................................30
5.4.3. IHRC Frequency Calibration and System Clock ........................................................31
5.4.4. External Crystal Oscillator .........................................................................................32
5.3.
5.4.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 3 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.4.5. System Clock and LVR level .....................................................................................34
5.4.6. System Clock Switching ............................................................................................35
Comparator...........................................................................................................................36
5.5.1 Internal reference voltage (Vinternal R)...........................................................................37
5.5.2 Using the comparator ................................................................................................39
5.5.3 Using the comparator and bandgap 1.20V.................................................................40
16-bit Timer (Timer16) ..........................................................................................................41
8-bit Timer (Timer2/Timer3) with PWM generation................................................................42
5.7.1 Using the Timer2 to generate periodical waveform....................................................44
5.7.2 Using the Timer2 to generate 8-bit PWM waveform...................................................45
5.7.3 Using the Timer2 to generate 6-bit / 7-bit PWM waveform.........................................47
5.7.4 Complementary PWM with Dead Zones....................................................................48
WatchDog Timer...................................................................................................................51
Interrupt ................................................................................................................................52
5.5.
5.6
5.7
5.8
5.9
5.10 Power-Save and Power-Down ..............................................................................................54
5.10.1 Power-Save mode (“stopexe”)...................................................................................54
5.10.2 Power-Down mode (“stopsys”) ..................................................................................55
5.10.3 Wake-up....................................................................................................................56
5.11 IO Pins..................................................................................................................................56
5.12 Reset and LVR......................................................................................................................59
5.12.1 Reset.........................................................................................................................59
5.12.2 LVR reset ..................................................................................................................59
5.13 Analog-to-Digital Conversion (ADC) module .........................................................................59
5.13.1 The input requirement for AD conversion ..................................................................60
5.13.2 Select the reference high voltage ..............................................................................61
5.13.3 ADC clock selection...................................................................................................61
5.13.4 Configure the analog pins..........................................................................................61
5.13.5 Using the ADC...........................................................................................................62
5.13.6 How to calculate ADC input voltage VIN .....................................................................63
6. IO Registers ........................................................................................................................64
6.1.
6.2.
6.3.
6.4.
6.5.
6.6.
6.7.
ACC Status Flag Register (flag), IO address = 0x00 .............................................................64
Stack Pointer Register (sp), IO address = 0x02 ....................................................................64
Clock Mode Register (clkmd), IO address = 0x03 .................................................................64
Interrupt Enable Register (inten), IO address = 0x04 ............................................................65
Interrupt Request Register (intrq), IO address = 0x05...........................................................65
Timer16 mode Register (t16m), IO address = 0x06...............................................................66
Timer2 Bound Register (tm2b), IO address = 0x09 ...............................................................66
©Copyright 2020, PADAUK Technology Co. Ltd
Page 4 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
6.8.
6.9.
External Oscillator setting Register (eoscr), IO address = 0x0a.............................................66
Interrupt Edge Select Register (integs), IO address = 0x0c...................................................67
6.10. Port A Digital Input Enable Register (padier), IO address = 0x0d..........................................67
6.11. Port B Digital Input Enable Register (pbdier), IO address = 0x0e..........................................67
6.12. Port A Data Register (pa), IO address = 0x10.......................................................................68
6.13. Port A Control Register (pac), IO address = 0x11 .................................................................68
6.14. Port A Pull-High Register (paph), IO address = 0x12 ............................................................68
6.15. Port B Data Register (pb), IO address = 0x14.......................................................................68
6.16. Port B Control Register (pbc), IO address = 0x15 .................................................................68
6.17. Port B Pull-High Register (pbph), IO address = 0x16 ............................................................68
6.18. Port B Pull Low Register (pbpl), IO address = 0x38 ..............................................................68
6.19. Miscellaneous Register (misc), IO address = 0x17................................................................69
6.20. Comparator Control Register (gpcc), IO address = 0x18.......................................................69
6.21. Comparator Selection Register (gpcs), IO address = 0x19....................................................70
6.22. Timer2 Control Register (tm2c), IO address = 0x1c ..............................................................70
6.23. Timer2 Counter Register (tm2ct), IO address = 0x1d............................................................71
6.24. Timer2 Scalar Register (tm2s), IO address = 0x1e................................................................71
6.25. Timer3 Control Register (tm3c), IO address = 0x32 ..............................................................71
6.26. Timer3 Counter Register (tm3ct), IO address = 0x33............................................................72
6.27. Timer3 Scalar Register (tm3s), IO address = 0x34................................................................72
6.28. Timer3 Bound Register (tm3b), IO address = 0x3f ................................................................72
6.29. ADC Control Register (adcc), IO address = 0x3b..................................................................72
6.30. ADC Mode Register (adcm), IO address = 0x3c....................................................................73
6.31. ADC Regulator Control Register (adcrgc), IO address = 0x3d...............................................73
6.32. ADC Result High Register (adcr), IO address = 0x3e............................................................73
7. Instructions.........................................................................................................................74
7.1.
7.2.
7.3.
7.4.
7.5.
7.6.
7.7.
7.8.
7.9.
Data Transfer Instructions.....................................................................................................75
Arithmetic Operation Instructions ..........................................................................................77
Shift Operation Instructions...................................................................................................79
Logic Operation Instructions..................................................................................................80
Bit Operation Instructions......................................................................................................82
Conditional Operation Instructions ........................................................................................83
System control Instructions ...................................................................................................84
Summary of Instructions Execution Cycle .............................................................................86
Summary of affected flags by Instructions.............................................................................86
7.10. BIT definition.........................................................................................................................86
8. Code Options......................................................................................................................87
©Copyright 2020, PADAUK Technology Co. Ltd
Page 5 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
9. Special Notes......................................................................................................................88
9.1.
9.2.
Warning ................................................................................................................................88
Using IC................................................................................................................................88
9.2.1. IO pin usage and setting............................................................................................88
9.2.2. Interrupt.....................................................................................................................89
9.2.3. System clock switching..............................................................................................89
9.2.4. Watchdog..................................................................................................................90
9.2.5. TIMER time out .........................................................................................................90
9.2.6. IHRC .........................................................................................................................90
9.2.7. LVR...........................................................................................................................91
9.2.8. Programming Writing.................................................................................................91
Using ICE..............................................................................................................................92
9.3
©Copyright 2020, PADAUK Technology Co. Ltd
Page 6 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Revision History:
Revision
Date
Description
0.00
2018/10/11
Preliminary version
1. Amend 1.1 Special Features
1.00
1.01
2018/11/07
2. Amend Fig. 4: Hardware diagram of comparator
3. Amend 9.2.8 Programming Writing
1. Amend 5.7.1, 5.7.2, and 5.7.3
2. Add Section 5.7.4 Complementary PWM with Dead Zones
3. Add Fig.13 and Fig.14
2019/08/23
4. Amend Section 5.10.1 and 5.10.3
5. Amend Section 5.13.5 Using the ADC
6. Amend Chapter 8 Code Options
7. Amend 9.2.8 Programming Writing
1. Amend Section 4.1 AC/DC Device Characteristics: VIL
2. Amend Section 6.3 Clock Mode Register
1. Amend Section 4.1 AC/DC Device Characteristics: LVR%, IOH, RPH,RPL
2. Update Section 4.3 to 4.16
1.02
1.03
2019/10/21
2020/09/02
3. Adjust Section 4.17 to 5.2.1
4. Amend Section 5.4.6, 5.5, 5.7, 6.21, 6.32, 9.2.7, 9.3
5. Add Section 5.13.6 How to calculate ADC input voltage VIN
6. Amend Chapter 8
©Copyright 2020, PADAUK Technology Co. Ltd
Page 7 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
1. Features
1.1. Special Features
General purpose OTP series
Not supposed to use in AC RC step-down powered or high EFT requirement applications.
PADAUK assumes no liability if such kind of applications can not pass the safety regulation tests.
Operating temperature range: -20°C ~ 70°C
1.2. System Features
1.5KW OTP program memory
96 Bytes data RAM
Clock sources: internal high RC oscillator, internal low RC oscillator and external crystal oscillator
Bandgap circuit to provide 1.20V reference voltage
One hardware 16-bit timer
Two hardware 8-bit timers with PWM generation
One hardware comparator
Up to 11-channel 8-bit resolution ADC with one channel comes from bandgap voltage
Provide ADC reference high voltage: external input, internal VDD
Eight levels of LVR reset by code option: 4.0V, 3.5V, 3.0V, 2.7V, 2.5V, 2.2V, 2.0V, 1.8V
Max. 14 IO pins with optional pull-high resistor, two of them with additional pull-low resistor
PB0 provides NMOS and PB7 provides PMOS super large current output (typ. 135mA@VDD=5.0V)
Two selectable external interrupt pins by code option
Every IO pin can be configured to enable wake-up function
For every wake-up enabled IO, two optional wake-up speed are supported: normal and fast
1.3. CPU Features
One processing unit operating mode
82 powerful instructions
Most instructions are 1T execution cycle
Programmable stack pointer to provide adjustable stack level
Support direct and indirect addressing modes for data access. Data memories are available for use as an
index pointer of Indirect addressing mode
IO space and memory space are independent
1.4. Package Information
PMS171B-S16: SOP16 (150mil)
PMS171B-1J16A: QFN3*3-16pin (0.5pitch)
PMS171B-S14: SOP14 (150mil)
PMS171B-M10: MSOP10 (118mil)
PMS171B-S08: SOP8 (150mil)
PMS171B-U06: SOT23-6 (60mil)
©Copyright 2020, PADAUK Technology Co. Ltd
Page 8 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
2. General Description and Block Diagram
The PMS171B family is an ADC-Type, fully static, OTP-based CMOS 8-bit microcontroller. It employs RISC
architecture and all the instructions are executed in one cycle except that some instructions are two cycles that
handle indirect memory access.
1.5KW OTP program memory and 96 bytes data SRAM are inside, one up to 11 channels 8-bit ADC is built
inside the chip with one channel for internal bandgap reference voltage. PMS171B also provides three hardware
timers: one is 16-bit timer and two are 8-bit timers with PWM generation. PMS171B also supports one hardware
comparator and two super large current outputs.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 9 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
3. Pin Definition and Functional Description
©Copyright 2020, PADAUK Technology Co. Ltd
Page 10 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
©Copyright 2020, PADAUK Technology Co. Ltd
Page 11 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Pin Type &
Buffer Type
Pin Name
Description
The functions of this pin can be:
(1) Bit 7 of port A. It can be configured as digital input, two-state output with pull-high
resistor by software independently.
IO
PA7 /
X1
ST /
(2) X1 is Crystal XIN when crystal oscillator is used.
CMOS
If this pin is used for crystal oscillator, bit 7 of padier register must be programmed “0”
to avoid leakage current. This pin can be used to wake-up system during sleep mode;
however, wake-up function is also disabled if bit 7 of padier register is “0”.
The functions of this pin can be:
(1) Bit 6 of port A. It can be configured as digital input, two-state output with pull-high
resistor by software independently.
IO
PA6 /
X2
ST /
(2) X2 is Crystal XOUT when crystal oscillator is used.
CMOS
If this pin is used for crystal oscillator, bit 6 of padier register must be programmed “0”
to avoid leakage current. This pin can be used to wake-up system during sleep mode;
however, wake-up function is also disabled if bit 6 of padier register is “0”.
The functions of this pin can be:
(1) Bit 5 of port A. It can be configured as digital input or open-drain output with
pull-high resistor by software independently.
PA5 /
IO (OD)
ST /
PRSTB
(2) Hardware reset.
CMOS
This pin can be used to wake-up system during sleep mode; however, wake-up
function is also disabled if bit 5 of padier register is “0”. Please put 33Ω resistor in
series to have high noise immunity when this pin is in input mode.
The functions of this pin can be:
(1) Bit 4 of port A. It can be configured as digital input, two-state output with pull-high
resistor by software independently.
(2) Channel 9 of ADC analog input.
PA4 /
AD9 /
(3) Plus input source of comparator.
IO
(4) Minus input source 1 of comparator.
ST /
CIN+ /
CIN1- /
INT1A
(5) External interrupt line 1A. It can be used as an external interrupt line 1. Both rising
edge and falling edge are accepted to request interrupt service and configurable
by register setting.
CMOS /
Analog
When this pin is configured as analog input, please use bit 4 of register padier to
disable the digital input to prevent current leakage. The bit 4 of padier register can be
set to “0” to disable digital input; wake-up from power-down by toggling this pin is also
disabled.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 12 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Pin Type &
Buffer Type
Pin Name
Description
The functions of this pin can be:
(1) Bit 3 of port A. It can be configured as digital input, two-state output with pull-high
resistor independently by software.
PA3 /
AD8 /
IO
(2) Channel 8 of ADC analog input.
ST /
(3) Minus input source 0 of comparator.
CIN0- /
TM2PWM
CMOS /
Analog
(4) PWM output from Timer2.
When this pin is configured as analog input, please use bit 3 of register padier to
disable the digital input to prevent current leakage. The bit 3 of padier register can be
set to “0” to disable digital input; wake-up from power-down by toggling this pin is also
disabled.
The functions of this pin can be:
(1) Bit 0 of port A. It can be configured as digital input, two-state output with pull-high
resistor independently by software.
PA0 /
AD10 /
CO /
IO
(2) Channel 10 of ADC analog input.
ST /
(3) Output of comparator.
CMOS /
Analog
(4) External interrupt line 0. It can be used as an external interrupt line 0. Both rising
edge and falling edge are accepted to request interrupt service and configurable
by register setting.
INT0
The bit 0 of padier register can be set to “0” to disable wake-up from power-down by
toggling this pin.
The functions of this pin can be:
(1) Bit 7 of port B. It can be configured as digital input, two-state output with pull-high
resistor independently by software.
PB7 /
AD7 /
IO
(2) Channel 7 of ADC analog input.
ST /
(3) Minus input source 5 of comparator.
CIN5- /
TM3PWM
CMOS /
Analog
(4) PWM output from Timer3.
When this pin is configured as analog input, please use bit 7 of register pbdier to
disable the digital input to prevent current leakage. The bit 7 of pbdier register can be
set to “0” to disable digital input; wake-up from power-down by toggling this pin is also
disabled.
The functions of this pin can be:
(1) Bit 6 of port B. It can be configured as digital input, two-state output with pull-high
/ pull-low resistor independently by software.
PB6 /
AD6 /
IO
(2) Channel 6 of ADC analog input.
ST /
(3) Minus input source 4 of comparator.
CIN4- /
TM3PWM
CMOS /
Analog
(4) PWM output from Timer3.
When this pin is configured as analog input, please use bit 6 of register pbdier to
disable the digital input to prevent current leakage. The bit 6 of pbdier register can be
set to “0” to disable digital input; wake-up from power-down by toggling this pin is also
disabled.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 13 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Pin Type &
Buffer Type
Pin Name
Description
The functions of this pin can be:
(1) Bit 5 of port B. It can be configured as digital input, two-state output with pull-high
resistor independently by software.
(2) Channel 5 of ADC analog input.
PB5 /
AD5 /
IO
(3) PWM output from Timer3.
ST /
(4) External interrupt line 0A. It can be used as an external interrupt line 0. Both rising
edge and falling edge are accepted to request interrupt service and configurable
by register setting.
TM3PWM /
INT0A
CMOS /
Analog
When this pin is configured as analog input, please use bit 5 of register pbdier to
disable the digital input to prevent current leakage. The bit 5 of pbdier register can be
set to “0” to disable digital input; wake-up from power-down by toggling this pin is also
disabled.
The functions of this pin can be:
(1) Bit 4 of port B. It can be configured as digital input, two-state output with pull-high
resistor independently by software.
IO
PB4 /
AD4 /
(2) Channel 4 of ADC analog input.
ST /
(3) PWM output from Timer2.
CMOS /
Analog
TM2PWM
When this pin is configured as analog input, please use bit 4 of register pbdier to
disable the digital input to prevent current leakage. The bit 4 of pbdier register can be
set to “0” to disable digital input; wake-up from power-down by toggling this pin is also
disabled.
The functions of this pin can be:
(1) Bit 3 of port B. It can be configured as digital input, two-state output with pull-high
/ pull-low resistor independently by software.
IO
PB3 /
AD3
ST /
(2) Channel 3 of ADC analog input.
CMOS /
Analog
When this pin is configured as analog input, please use bit 3 of register pbdier to
disable the digital input to prevent current leakage. The bit 3 of pbdier register can
be set to “0” to disable digital input; wake-up from power-down by toggling this pin is
also disabled.
The functions of this pin can be:
(1) Bit 2 of port B. It can be configured as digital input, two-state output with pull-high
resistor independently by software.
IO
PB2 /
AD2 /
(2) Channel 2 of ADC analog input.
ST /
(3) PWM output from Timer2.
CMOS /
Analog
TM2PWM
When this pin is configured as analog input, please use bit 2 of register pbdier to
disable the digital input to prevent current leakage. The bit 2 of pbdier register can
be set to “0” to disable digital input; wake-up from power-down by toggling this pin is
also disabled.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 14 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Pin Type &
Buffer Type
Pin Name
Description
The functions of this pin can be:
(1) Bit 1 of port B. It can be configured as digital input, two-state output with pull-high
resistor independently by software.
IO
PB1 /
AD1 /
Vref
(2) Channel 1 of ADC analog input.
ST /
(3) External reference high voltage for ADC.
CMOS /
Analog
When this pin is configured as analog input, please use bit 1 of register pbdier to
disable the digital input to prevent current leakage. The bit 1 of pbdier register can
be set to “0” to disable digital input; wake-up from power-down by toggling this pin is
also disabled.
The functions of this pin can be:
(1) Bit 0 of port B. It can be configured as input or open-drain output pin.
(2) PWM output from Timer2.
PB0 /
TM2PWM /
INT1
IO (OD)
ST /
(3) External interrupt line 1. It can be used as an external interrupt line 1. Both rising
edge and falling edge are accepted to request interrupt service and configurable
by register setting.
CMOS
Please note that PB0 does NOT have pull-high resistor.
If bit 0 of pbdier register is set to “0” to disable digital input, wake-up from
power-down by toggling this pin is also disabled.
VDD: Digital positive power
VDD /
AVDD
VDD /
AVDD
AVDD: Analog positive power
VDD is the IC power supply while AVDD is the ADC power supply. AVDD and VDD
are double bonding internally and they have the same external pin.
GND: Digital negative power
GND /
AGND
GND /
AGND
AGND: Analog negative power
GND is the IC ground pin while AGND is the ADC ground pin. AGND and GND are
double bonding internally and they have the same external pin.
Notes: IO: Input/Output; ST: Schmitt Trigger input; OD: Open Drain; Analog: Analog input pin;
CMOS: CMOS voltage level
©Copyright 2020, PADAUK Technology Co. Ltd
Page 15 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
4. Device Characteristics
4.1. AC/DC Device Characteristics
All data are acquired under the conditions of VDD=5.0V, fSYS =2MHz unless noted.
Symbol
VDD
Description
Operating Voltage
Min
1.8*
-5
Typ.
Max
5.5
5
Unit
V
Conditions (Ta=25oC)
5.0
* Subject to LVR tolerance
LVR%
Low Voltage Reset Tolerance
%
System clock (CLK)* =
IHRC/2
0
0
0
8M
4M
2M
VDD ≧3.0V
VDD ≧2.2V
VDD ≧1.8V
fSYS
IHRC/4
Hz
IHRC/8
ILRC
50K
0.7
35
VDD = 5.0V
mA fSYS=IHRC/16=1MIPS@5.0V
uA fSYS=ILRC=50KHz@3.3V
uA fSYS= 0Hz, VDD =5.0V
Operating Current
IOP
IPD
IPS
Power Down Current
(by stopsys command)
Power Save Current
(by stopexe command)
1
0.6
uA fSYS= 0Hz, VDD =3.3V
VDD =5.0V; fSYS= ILRC
3
uA
V
Only ILRC module is enabled.
VIL
VIH
Input low voltage for IO lines
Input high voltage for IO lines
0
0.1 VDD
0.8 VDD
0.7 VDD
VDD
VDD
PA5
V
other IO
IO lines sink current
PB0
135
16
PB4, PB5 (normal)
PB4, PB5 (strong)
others
IOL
mA VDD=5.0V, VOL=0.5V
38
16
IO lines drive current
PA5, PB0
0
14
20
135
6
PB4, PB5 (normal)
PB4, PB5 (strong)
PB7
IOH
mA VDD=5.0V, VOH=4.5V
others
VIN
Input voltage
-0.3
VDD +0.3
1
V
mA
VDD +0.3≧VIN≧ -0.3
IINJ (PIN)
Injected current on pin
PA5
120
75
VDD=5.0V
RPH
PB7
KΩ VDD=5.0V
VDD=5.0V
Others (except PB0)
82
61
VDD =5.0V
RPL
Pull-Low Resistance
100
180
KΩ
VDD =3.3V
VDD =2.2V
VDD =1.8V ~ 5.5V
-20oC <Ta<70oC*
VBG
Bandgap Reference Voltage
1.145*
1.20*
1.255*
V
©Copyright 2020, PADAUK Technology Co. Ltd
Page 16 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Symbol
Description
Min
Typ
Max
Unit
Conditions (Ta=25oC)
* Subject to LVR tolerance
25oC, VDD =2.0V~5.5V
VDD =2.0V~5.5V,
VPOR
Power On Reset Voltage
1.8
V
15.76*
15.20*
16.24*
16.80*
Frequency of IHRC after
0oC <Ta<70oC*
fIHRC
16*
MHz
calibration *
VDD =1.8V~5.5V,
0oC <Ta<70oC*
13.60*
18.40*
tINT
Interrupt pulse width
ADC Input Voltage
ADC resolution
30
0
-
-
-
ns
V
VDD = 5.0V
VADC
ADrs
VDD
-
8
bit
mA
0.9
0.8
2
@5V
ADcs
ADclk
ADC current consumption
-
-
-
-
@3V
ADC clock period
us
1.8V ~ 5.5V
ADC conversion time
tADCONV
(TADCLK is the period of the
selected AD conversion clock)
ADC Differential NonLinearity
ADC Integral NonLinearity
ADC offset*
-
15
-
TADCLK
8-bit resolution
AD DNL
AD INL
ADos
±2*
±4*
5*
LSB
LSB
mV
V
@ VDD =3V
VDR
RAM data retention voltage*
1.5
in stop mode
8k
misc[1:0]=00 (default)
misc[1:0]=01
16k
tWDT
Watchdog timeout period
TILRC
64k
misc[1:0]=10
misc[1:0]=11
256k
Wake-up time period for fast
wake-up
45
Where TILRC is the time
period of ILRC
tWUP
TILRC
Wake-up time period for
normal wake-up
3000
System boot-up period from
power-on for Normal boot-up
System boot-up period from
power-on for Fast boot-up
55
ms
us
VDD =5V
tSBP
820
VDD =5V
tRST
External reset pulse width
120
-
us
@ VDD =5V
CPos
Comparator offset*
Comparator input common
mode*
±10
±20
mV
VDD -1.5
CPcm
CPspt
CPmc
0
V
Comparator response time**
100
2.5
500
7.5
ns
us
Both Rising and Falling
Stable time to change
comparator mode
Comparator
consumption
current
CPcs
20
uA
VDD = 3.3V
©Copyright 2020, PADAUK Technology Co. Ltd
Page 17 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
*These parameters are for design reference, not tested for each chip.
4.2. Absolute Maximum Ratings
Supply Voltage …………………………….....
1.8V ~ 5.5V
Input Voltage ………………………………….. -0.3V ~ VDD + 0.3V
Operating Temperature ............................... -20oC ~ 70oC
Junction Temperature ………………………… 150°C
Storage Temperature ………………………… -50°C ~ 125°C
4.3. Typical ILRC frequency vs. VDD
©Copyright 2020, PADAUK Technology Co. Ltd
Page 18 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
4.4. Typical IHRC frequency deviation vs. VDD (calibrated to 16MHz)
4.5. Typical ILRC Frequency vs. Temperature
©Copyright 2020, PADAUK Technology Co. Ltd
Page 19 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
4.6. Typical IHRC Frequency vs. Temperature (calibrated to 16MHz)
4.7. Typical operating current vs. VDD @ system clock = ILRC/n
Conditions:
ON: Bandgap, LVR, ILRC; OFF: IHRC, EOSC, T16, TM2, TM3, ADC modules;
IO: PA0:0.5Hz output toggle and no loading, others: input and no floating
©Copyright 2020, PADAUK Technology Co. Ltd
Page 20 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
4.8. Typical operating current vs. VDD @ system clock = IHRC/n
Conditions:
ON: Bandgap, LVR, IHRC; OFF: ILRC, EOSC, LVR, T16, TM2, TM3, ADC modules;
IO: PA0:0.5Hz output toggle and no loading, others: input and no floating
4.9. Typical operating current vs. VDD @ system clock = 4MHz EOSC / n
Conditions:
ON: Bandgap, LVR, EOSC, MISC.6 = 1; OFF: IHRC, ILRC, T16, TM2, TM3, ADC modules;
IO: PA0:0.5Hz output toggle and no loading, others: input and no floating
©Copyright 2020, PADAUK Technology Co. Ltd
Page 21 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
4.10.Typical operating current vs. VDD @ system clock = 32KHz EOSC / n
Conditions:
ON: Bandgap, LVR, EOSC, MISC.6 = 1; OFF: IHRC, ILRC, T16, TM2, TM3, ADC modules;
IO: PA0:0.5Hz output toggle and no loading, others: input and no floating
4.11.Typical operating current vs. VDD @ system clock = 1MHz EOSC / n
Conditions:
ON: Bandgap, LVR, EOSC, MISC.6 = 1; OFF: IHRC, ILRC, T16, TM2, TM3, ADC modules;
IO: PA0:0.5Hz output toggle and no loading, others: input and no floating
©Copyright 2020, PADAUK Technology Co. Ltd
Page 22 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
4.12.Typical IO driving current (IOH) and sink current (IOL)
(VOH=0.9*VDD, VOL=0.1*VDD)
©Copyright 2020, PADAUK Technology Co. Ltd
Page 23 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
©Copyright 2020, PADAUK Technology Co. Ltd
Page 24 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
4.13. Typical IO input high/low threshold voltage (VIH/VIL)
4.14. Typical resistance of IO pull high device
©Copyright 2020, PADAUK Technology Co. Ltd
Page 25 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
4.15. Typical resistance of IO pull Low device
©Copyright 2020, PADAUK Technology Co. Ltd
Page 26 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
4.16. Typical power down current (IPD) and power save current (IPS)
©Copyright 2020, PADAUK Technology Co. Ltd
Page 27 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5. Functional Description
5.1. Program Memory - OTP
The OTP (One Time Programmable) program memory is used to store the program instructions to be executed.
The OTP program memory may contains the data, tables and interrupt entry. After reset, the initial address
0x000 is reserved for system using, so the program will start from 0x001 which is GOTO FPPA0 instruction
usually. The interrupt entry is 0x10 if used, the last 24 addresses are reserved for system using, like checksum,
serial number, etc. The OTP program memory for PMS171B is 1.5Kx14 bit that is partitioned as Table 1. The
OTP memory from address “0x5E8 to 0x5FF” is for system using, address space from “0x002 to 0x00F” and
from “0x011 to 0x5E7” are user program spaces.
Address
0x000
0x001
0x002
•
Function
System Using
GOTO FPPA0 instruction
User program
•
0x00F
0x010
0x011
•
User program
Interrupt entry address
User program
•
0x5E7
0x5E8
•
User program
System Using
•
0x5FF
System Using
Table 1: Program Memory Organization
5.2. Boot Procedure
POR (Power-On-Reset) is used to reset PMS171B when power up. The boot up time can be optional fast or
normal. Customer must ensure the stability of supply voltage after power up no matter which option is chosen,
the power up sequence is shown in the Fig. 1 and tSBP is the boot up time.
Please noted, during Power-On-Reset, the VDD must go higher than VPOR to boot-up the MCU.
Fig. 1: Power-Up Sequence
©Copyright 2020, PADAUK Technology Co. Ltd
Page 28 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.2.1. Timing charts for reset conditions
LVR level
SBP
VDD
LVR
t
Program
Execution
Boot up from LVR detection
VDD
t
SBP
WD
Time Out
Program
Execution
Boot up from Watch Dog Time Out
©Copyright 2020, PADAUK Technology Co. Ltd
Page 29 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.3. Data Memory - SRAM
The access of data memory can be byte or bit operation. Besides data storage, the SRAM data memory is also
served as data pointer of indirect access method and the stack memory.
The stack memory is defined in the data memory. The stack pointer is defined in the stack pointer register; the
depth of stack memory of each processing unit is defined by the user. The arrangement of stack memory fully
flexible and can be dynamically adjusted by the user.
For indirect memory access mechanism, the data memory is used as the data pointer to address the data byte.
All the data memory could be the data pointer; it’s quite flexible and useful to do the indirect memory access.
Since the data width is 8-bit, all the 96 bytes data memory of PMS171B can be accessed by indirect access
mechanism.
5.4. Oscillator and clock
There are three oscillator circuits provided by PMS171B: external crystal oscillator (EOSC), internal high RC
oscillator (IHRC) and internal low RC oscillator (ILRC), and these three oscillators are enabled or disabled by
registers eoscr.7, clkmd.4 and clkmd.2 independently. User can choose one of these three oscillators as
system clock source and use clkmd register to target the desired frequency as system clock to meet different
applications.
Oscillator Module
EOSC
Enable/Disable
eoscr.7
IHRC
clkmd.4
ILRC
clkmd.2
Table 2: Three oscillation circuits
5.4.1. Internal High RC oscillator and Internal Low RC oscillator
After boot-up, the IHRC and ILRC oscillators are enabled. The frequency of IHRC can be calibrated to
eliminate process variation by ihrcr register; normally it is calibrated to 16MHz. Please refer to the
measurement chart for IHRC frequency verse VDD and IHRC frequency verse temperature. The frequency of
ILRC will vary by process, supply voltage and temperature, please refer to DC specification and do not use for
accurate timing application.
5.4.2. Chip calibration
The IHRC frequency and bandgap reference voltage may be different chip by chip due to manufacturing
variation, PMS171B provide the IHRC frequency calibration to eliminate this variation, and this function can be
selected when compiling user’s program and the command will be inserted into user’s program automatically.
The calibration command is shown as below:
.ADJUST_IC SYSCLK=IHRC/(p1), IHRC=(p2)MHz, VDD=(p3)V;
Where, p1=2, 4, 8, 16, 32; In order to provide different system clock.
p2=14 ~ 18; In order to calibrate the chip to different frequency, 16MHz is the usually one.
p3=2.5 ~ 5.5; In order to calibrate the chip under different supply voltage.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 30 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.4.3. IHRC Frequency Calibration and System Clock
During compiling the user program, the options for IHRC calibration and system clock are shown as Table 3:
SYSCLK
○ Set IHRC / 2
○ Set IHRC / 4
○ Set IHRC / 8
○ Set IHRC / 16
○ Set IHRC / 32
○ Set ILRC
CLKMD
IHRCR
Calibrated
Calibrated
Calibrated
Calibrated
Calibrated
Calibrated
No Change
Description
= 34h (IHRC / 2)
= 14h (IHRC / 4)
= 3Ch (IHRC / 8)
= 1Ch (IHRC / 16)
= 7Ch (IHRC / 32)
= E4h (ILRC / 1)
No change
IHRC calibrated to 16MHz, CLK=8MHz (IHRC/2)
IHRC calibrated to 16MHz, CLK=4MHz (IHRC/4)
IHRC calibrated to 16MHz, CLK=2MHz (IHRC/8)
IHRC calibrated to 16MHz, CLK=1MHz (IHRC/16)
IHRC calibrated to 16MHz, CLK=0.5MHz (IHRC/32)
IHRC calibrated to 16MHz, CLK=ILRC
○ Disable
IHRC not calibrated, CLK not changed
Table 3: Options for IHRC Frequency Calibration
Usually, .ADJUST_IC will be the first command after boot up, in order to set the target operating frequency
whenever starting the system. The program code for IHRC frequency calibration is executed only one time that
occurs in writing the codes into OTP memory; after then, it will not be executed again. If the different option for
IHRC calibration is chosen, the system status is also different after boot. The following shows the status of
PMS171B for different option:
(1) .ADJUST_IC
SYSCLK=IHRC/2, IHRC=16MHz, VDD=5V
After boot up, CLKMD = 0x34:
IHRC frequency is calibrated to 16MHz@VDD=5V and IHRC module is enabled
System CLK = IHRC/2 = 8MHz
Watchdog timer is disabled, ILRC is enabled, PA5 is in input mode
(2) .ADJUST_IC
SYSCLK=IHRC/4, IHRC=16MHz, VDD=3.3V
After boot up, CLKMD = 0x14:
IHRC frequency is calibrated to 16MHz@VDD=3.3V and IHRC module is enabled
System CLK = IHRC/4 = 4MHz
Watchdog timer is disabled, ILRC is enabled, PA5 is in input mode
(3) .ADJUST_IC
SYSCLK=IHRC/8, IHRC=16MHz, VDD=2.5V
After boot up, CLKMD = 0x3C:
IHRC frequency is calibrated to 16MHz@VDD=2.5V and IHRC module is enabled
System CLK = IHRC/8 = 2MHz
Watchdog timer is disabled, ILRC is enabled, PA5 is in input mode
(4) .ADJUST_IC
SYSCLK=IHRC/16, IHRC=16MHz, VDD=2.5V
After boot up, CLKMD = 0x1C:
IHRC frequency is calibrated to 16MHz@VDD=2.5V and IHRC module is enabled
System CLK = IHRC/16 = 1MHz
Watchdog timer is disabled, ILRC is enabled, PA5 is in input mode
©Copyright 2020, PADAUK Technology Co. Ltd
Page 31 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
(5) .ADJUST_IC
SYSCLK=IHRC/32, IHRC=16MHz, VDD=5V
After boot up, CLKMD = 0x7C:
IHRC frequency is calibrated to 16MHz@VDD=5V and IHRC module is enabled
System CLK = IHRC/32 = 500KHz
Watchdog timer is disabled, ILRC is enabled, PA5 is in input mode
SYSCLK=ILRC, IHRC=16MHz, VDD=5V
(6) .ADJUST_IC
After boot up, CLKMD = 0XE4:
IHRC frequency is calibrated to 16MHz@VDD=5V and IHRC module is disabled
System CLK = ILRC
Watchdog timer is disabled, ILRC is enabled, PA5 is input mode
DISABLE
(7) .ADJUST_IC
After boot up, CLKMD is not changed (Do nothing):
IHRC is not calibrated and IHRC module is disabled
System CLK = ILRC or IHRC/64
Watchdog timer is enabled, ILRC is enabled, PA5 is in input mode
5.4.4. External Crystal Oscillator
If crystal oscillator is used, a crystal or resonator is required between X1 and X2. Fig. 2 shows the hardware
connection under this application; the range of operating frequency of crystal oscillator can be from 32 KHz to
4MHz, depending on the crystal placed on; higher frequency oscillator than 4MHz is NOT supported.
(Select driving current for oscillator)
eoscr[6:5]
(Enable crystal oscillator)
eoscr.7
C1
PA7/X1
System clock = EOSC
PA6/X2
C2
The values of C1 and C2 should depend on
the specification of crystal.
Fig. 2: Connection of crystal oscillator
Besides crystal, external capacitor and options of PMS171B should be fine tuned in eoscr (0x0b) register to
have good sinusoidal waveform. The eoscr.7 is used to enable crystal oscillator module, eoscr.6 and eoscr.5
are used to set the different driving current to meet the requirement of different frequency of crystal oscillator:
eoscr.[6:5]=01 : Low driving capability, for lower frequency, ex: 32KHz crystal oscillator
eoscr.[6:5]=10 : Middle driving capability, for middle frequency, ex: 1MHz crystal oscillator
eoscr.[6:5]=11 : High driving capability, for higher frequency, ex: 4MHz crystal oscillator
©Copyright 2020, PADAUK Technology Co. Ltd
Page 32 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Table 4 shows the recommended values of C1 and C2 for different crystal oscillator; the measured start-up
time under its corresponding conditions is also shown. Since the crystal or resonator had its own characteristic,
the capacitors and start-up time may be slightly different for different type of crystal or resonator, please refer to
its specification for proper values of C1 and C2.
Frequency
4MHz
C1
C2
Measured Start-up time
Conditions
4.7pF
10pF
22pF
4.7pF
10pF
22pF
6ms
11ms
450ms
(eoscr[6:5]=11, misc.6=0)
(eoscr[6:5]=10, misc.6=0)
(eoscr[6:5]=01, misc.6=0)
1MHz
32KHz
Table 4: Recommend values of C1 and C2 for crystal and resonator oscillators
When using the crystal oscillator, user must pay attention to the stable time of oscillator after enabling it, the
stable time of oscillator will depend on frequency, crystal type, external capacitor and supply voltage. Before
switching the system to the crystal oscillator, user must make sure the oscillator is stable; the reference
program is shown as below:
void
{
FPPA0 (void)
. ADJUST_IC SYSCLK=IHRC/16, IHRC=16MHz, VDD=5V
$
$
EOSCR
Enable, 4MHz;
// EOSCR = 0b110_00000;
T16M EOSC, /1, BIT13;
// T16 receive 2^14=16384 clocks of crystal EOSC
// Intrq.T16 =>1, crystal EOSC Is stable
WORD
count =
0;
stt16 count;
Intrq.T16
=
0;
do
{
nop; }while(!Intrq.T16);
// count fm 0x0000 to 0x2000, then set INTRQ.T16
// switch system clock to EOSC;
// close IHRC
clkmd=
clkmd.4=0;
...
0xB4;
Please notice that the crystal oscillator should be fully turned off before entering the power-down mode, in
order to avoid unexpected wakeup event.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 33 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.4.5. System Clock and LVR level
The clock source of system clock comes from EOSC, IHRC and ILRC, the hardware diagram of system clock
in the PMS171B is shown as Fig. 3.
clkmd[7:5]
÷2, ÷4,
÷8, ÷16, ÷32, ÷64
IHRC
clock
System
clock
M
EOSC
clock
÷1, ÷2, ÷4, ÷8
CLK
U
X
ILRC
÷1 (default), ÷4, ÷16
clock
Fig. 3: Options of System Clock
User can choose different operating system clock depends on its requirement; the selected operating system
clock should be combined with supply voltage and LVR level to make system stable. The LVR level will be
selected during compilation, and the lowest LVR levels can be chosen for different operating frequencies.
Please refer to Section 4.1.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 34 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.4.6. System Clock Switching
After IHRC calibration, user may want to switch system clock to a new frequency or may switch system clock at
any time to optimize the system performance and power consumption. Basically, the system clock of PMS171B
can be switched among IHRC, ILRC and EOSC by setting the clkmd register at any time; system clock will be
the new one after writing to clkmd register immediately. Please notice that the original clock module can NOT
be turned off at the same time as writing command to clkmd register. The examples are shown as below and
more information about clock switching, please refer to the “Help” -> “Application Note” -> “IC Introduction” ->
“Register Introduction” -> CLKMD”.
Case 1: Switching system clock from ILRC to IHRC/2
…
//
//
//
//
system clock is ILRC
CLKMD.4
CLKMD
// CLKMD.2
…
=
1;
turn on IHRC first to improve anti-interference ability
switch to IHRC/2, ILRC CAN NOT be disabled here
if need, ILRC CAN be disabled at this time
=
0x34;
0;
=
Case 2: Switching system clock from ILRC to EOSC
…
//
//
//
system clock is ILRC
CLKMD
CLKMD.2
…
=
=
0xA6;
0;
switch to IHRC, ILRC CAN NOT be disabled here
ILRC CAN be disabled at this time
Case 3: Switching system clock from IHRC/2 to ILRC
…
//
//
//
system clock is IHRC/2
CLKMD
CLKMD.4
…
=
=
0xF4;
0;
switch to ILRC, IHRC CAN NOT be disabled here
IHRC CAN be disabled at this time
Case 4: Switching system clock from IHRC/2 to EOSC
…
//
//
//
system clock is IHRC/2
CLKMD
CLKMD.4
…
=
=
0XB0;
0;
switch to EOSC, IHRC CAN NOT be disabled here
IHRC CAN be disabled at this time
Case 5: Switching system clock from IHRC/2 to IHRC/4
…
//
//
system clock is IHRC/2, ILRC is enabled here
switch to IHRC/4
CLKMD
…
=
0X14;
Case 6: System may hang if it is to switch clock and turn off original oscillator at the same time
…
//
system clock is ILRC
CLKMD
=
0x30;
//
CAN NOT switch clock from ILRC to IHRC/2 and
turn off ILRC oscillator at the same time
©Copyright 2020, PADAUK Technology Co. Ltd
Page 35 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.5. Comparator
One hardware comparator is built inside the PMS171B; Fig. 4 shows its hardware diagram. It can compare
signals between two pins or with either internal reference voltage Vinternal R or internal bandgap reference voltage.
The two signals to be compared, one is the plus input and the other one is the minus input. For the minus input of
comparator can be PA3, PA4, Internal bandgap 1.20 volt, PB6, PB7 or Vinternal R selected by bit [3:1] of gpcc
register, and the plus input of comparator can be PA4 or Vinternal R selected by bit 0 of gpcc register.
The comparator result can be selected through gpcs.7 to forcibly output to PA0 whatever it is input or output
state. It can be a direct output , or sampled by Timer2 clock (TM2_CLK) which comes from Timer2 module
through gpcc.5. The output polarity can be also inverted by setting gpcc.4register, the comparator output can be
used to request interrupt service or read through gpcc.6.
16 stages
VDD
gpcs.5=1
gpcs.4=0
gpcs.4=1
gpcs.5=0
MUX
gpcs[3:0]
Vinternal R
gpcc[3:1]
PA3/CIN0-
PA4/CIN1-
Bandgap
000
001 M
gpcc.4
To request interrupt
gpcc.6
010 U
011 X
100
X
O
R
-
PB6/CIN4-
PB7/CIN5-
M
U
X
101
+
D
F
F
To
PA0
0
Timer 2
clock
MUX
1
PA4/CIN+
gpcc.0
TM2_CLK
gpcc.5
gpcs.7
Fig. 4: Hardware diagram of comparator
©Copyright 2020, PADAUK Technology Co. Ltd
Page 36 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.5.1 Internal reference voltage (Vinternal R
)
The internal reference voltage Vinternal R is built by series resistance to provide different level of reference
voltage, bit 4 and bit 5 of gpcs register are used to select the maximum and minimum values of Vinternal R
and bit [3:0] of gpcs register are used to select one of the voltage level which is deivided-by-16 from the
defined maximum level to minimum level. Fig. 5 to Fig. 8 shows four conditions to have different reference
voltage Vinternal R. By setting the gpcs register, the internal reference voltage Vinternal R can be ranged from
(1/32)*VDD to (3/4)*VDD.
Case 1 : gpcs.5=0 & gpcs.4=0
16 stages
VDD
8R
8R
8R
gpcs.4=0
gpcs.4=1
gpcs.5=1
R
R
R
R
gpcs.5=0
MUX
gpcs[3:0]
V internal R = (3/4) VDD ~ (1/4) VDD + (1/32) VDD
@ gpcs[3:0] = 1111 ~ gpcs[3:0] = 0000
1
4
(n+1)
32
V internal R
=
*
VDD +
*
VDD, n = gpcs[3:0] in decimal
Fig. 5: Vinternal R hardware connection if gpcs.5=0 and gpcs.4=0
Case 2 : gpcs.5=0 & gpcs.4= 1
16 stages
VDD
8R
8R
8R
gpcs.4=0
gpcs.4=1
gpcs.5=1
R
R
R
R
gpcs.5=0
MUX
gpcs[3:0]
V
internal R = (2/3) VDD ~ (1/24) VDD
@ gpcs[3:0] = 1111 ~ gpcs[3:0] = 0000
(n+1)
V internal R
=
*
VDD, n = gpcs[3:0] in decimal
24
Fig. 6: Vinternal R hardware connection if gpcs.5=0 and gpcs.4=1
©Copyright 2020, PADAUK Technology Co. Ltd
Page 37 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Case 3 : gpcs.5=1 & gpcs.4= 0
16 stages
VDD
8R
8R
8R
gpcs.4=0
gpcs.4=1
gpcs.5=1
R
R
R
R
gpcs.5=0
MUX
gpcs[3:0]
V internal R = (3/5) VDD ~ (1/5) VDD + (1/40) VDD
@ gpcs[3:0] = 1111 ~ gpcs[3:0] = 0000
1
5
(n+1)
40
V internal R
=
*
VDD +
*
VDD, n = gpcs[3:0] in decimal
Fig. 7: Vinternal R hardware connection if gpcs.5=1 and gpcs.4=0
Case 4 : gpcs.5=1 & gpcs.4=1
16 stages
VDD
8R
8R
8R
gpcs.4=0
gpcs.4=1
gpcs.5=1
R
R
R
R
gpcs.5=0
MUX
gpcs[3:0]
V internal R = (1/2) VDD ~ (1/32) VDD
@ gpcs[3:0] = 1111 ~ gpcs[3:0] = 0000
(n+1)
V internal R
=
*
VDD, n = gpcs[3:0] in decimal
32
Fig. 8: Vinternal R hardware connection if gpcs.5=1 and gpcs.4=1
©Copyright 2020, PADAUK Technology Co. Ltd
Page 38 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.5.2
Using the comparator
Case 1:
Choosing PA3 as minus input and Vinternal R with (18/32)*VDD voltage level as plus input. Vinternal R is
configured as the above Figure “gpcs[5:4] = 2b’00” and gpcs [3:0] = 4b’1001 (n=9) to have Vinternal R
(1/4)*VDD + [(9+1)/32]*VDD = [(9+9)/32]*VDD = (18/32)*VDD.
=
gpcs = 0b0_0_00_1001;
gpcc = 0b1_0_0_0_000_0;
padier = 0bxxxx_0_xxx;
// Vinternal R = VDD*(18/32)
// enable comp, - input: PA3, + input: Vinternal R
// disable PA3 digital input to prevent leakage current
or
$ GPCS
VDD*18/32;
$ GPCC Enable, N_PA3, P_R;
PADIER = 0bxxxx_0_xxx;
// - input: N_xx,+ input: P_R(Vinternal R)
Case 2:
Choosing Vinternal R as minus input with (22/40)*VDD voltage level and PA4 as plus input, the comparator
result will be inversed and then output to PA0. Vinternal R is configured as the above Figure “gpcs[5:4] =
2b’10” and gpcs [3:0] = 4b’1101 (n=13) to have Vinternal R = (1/5)*VDD + [(13+1)/40]*VDD = [(13+9)/40]*VDD
(22/40)*VDD.
=
gpcs = 0b1_0_10_1101;
gpcc = 0b1_0_0_1_011_1;
padier = 0bxxx_0_xxxx;
// output to PA0, Vinternal R = VDD*(22/40)
// Inverse output, - input: Vinternal R, + input: PA4
// disable PA4 digital input to prevent leakage current
or
$ GPCS Output, VDD*22/40;
$ GPCC Enable, Inverse, N_R, P_PA4;
PADIER = 0bxxx_0_xxxx;
// - input: N_R(Vinternal R),+ input: P_xx
Note: When selecting output to PA0 output, GPCS will affect the PA3 output function in ICE. Though the
IC is fine, be careful to avoid this error during emulation.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 39 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.5.3 Using the comparator and bandgap 1.20V
The internal bandgap module can provide 1.20 volt, it can measure the external supply voltage level. The
bandgap 1.20 volt is selected as minus input of comparator and Vinternal R is selected as plus input, the
supply voltage of Vinternal R is VDD, the VDD voltage level can be detected by adjusting the voltage level of
Vinternal R to compare with bandgap. If N (gpcs[3:0] in decimal) is the number to let Vinternal R closest to
bandgap 1.20 volt, the supply voltage VDD can be calculated by using the following equations:
For using Case 1:
VDD = [ 32 / (N+9) ] * 1.20 volt ;
For using Case 2: VDD= [ 24 / (N+1) ] * 1.20 volt ;
For using Case 3:
For using Case 4:
V
DD = [ 40 / (N+9) ] * 1.20 volt ;
DD = [ 32 / (N+1) ] * 1.20 volt ;
V
Case 1:
$ GPCS VDD*12/40;
// 4.0V * 12/40 = 1.2V
$ GPCC Enable, BANDGAP, P_R;
// - input: BANDGAP, + input: P_R(Vinternal R)
….
if (GPC_Out)
// or GPCC.6
{
// when VDD﹥4V
}
else
{
// when VDD﹤4V
}
©Copyright 2020, PADAUK Technology Co. Ltd
Page 40 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.6 16-bit Timer (Timer16)
A 16-bit hardware timer (Timer16) is implemented in the PMS171B, the clock sources of Timer16 may come
from system clock (CLK), clock of external crystal oscillator (EOSC), internal high RC oscillator (IHRC),
internal low RC oscillator (ILRC), PA4 and PA0, a multiplex is used to select clock output for the clock source.
Before sending clock to the counter16, a pre-scaling logic with divided-by-1, 4, 16, and 64 is used for wide
range counting.
The 16-bit counter performs up-counting operation only, the counter initial values can be stored from memory
by stt16 instruction and the counting values can be loaded to memory by ldt16 instruction. A selector is used to
select the interrupt condition of Timer16, whenever overflow occurs, the Timer16 interrupt can be triggered.
The hardware diagram of Timer16 is shown as Fig. 9. The interrupt source of Timer16 comes from one of bit 8
to 15 of 16-bit counter, and the interrupt type can be rising edge trigger or falling edge trigger which is specified
in the bit 4 of integs register (IO address 0x0C).
PA4
Fig. 9: Hardware diagram of Timer16
When using the Timer16, the syntax for Timer16 has been defined in the .INC file. There are three parameters
to define the Timer16; 1st parameter is used to define the clock source of Timer16, 2nd parameter is used to
define the pre-scalar and the last one is to define the interrupt source. The detail description is shown as
below:
T16M IO_RW
0x06
$ 7~5:STOP, SYSCLK, X, PA4_F, IHRC, EOSC, ILRC, PA0_F
$ 4~3:/1, /4, /16, /64
// 1st par.
// 2nd par.
// 3rd par.
$ 2~0:BIT8, BIT9, BIT10, BIT11, BIT12, BIT13, BIT14, BIT15
©Copyright 2020, PADAUK Technology Co. Ltd
Page 41 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
User can define the parameters of T16M based on system requirement, some examples are shown below and
more examples please refer to “Help Application Note IC Introduction Register Introduction T16M” in
IDE utility.
$ T16M SYSCLK, /64, BIT15;
// choose (SYSCLK/64) as Timer16 clock source, every 2^16 clock to set INTRQ.2=1
// if using System Clock = IHRC / 2 = 8 MHz
// SYSCLK/64 = 8 MHz/64 = 125KHz, about every 512 mS to generate INTRQ.2=1
$ T16M EOSC, /1, BIT13;
// choose (EOSC/1) as Timer16 clock source, every 2^14 clocks to generate INTRQ.2=1
// if EOSC=32768 Hz, 32768 Hz/(2^14) = 2Hz, every 0.5S to generate INTRQ.2=1
$ T16M PA0_F, /1, BIT8;
// choose PA0 as Timer16 clock source, every 2^9 to generate INTRQ.2=1
// receiving every 512 times PA0 to generate INTRQ.2=1
$ T16M STOP;
// stop Timer16 counting
If Timer16 is operated at free running, the frequency of interrupt can be described as below:
FINTRQ_T16M = Fclock source ÷ P ÷ 2n+1
Where, F is the frequency of selected clock source to Timer16;
P is the selection of t16m [4:3]; (1, 4, 16, 64)
N is the nth bit selected to request interrupt service, for example: n=10 if bit 10 is selected.
5.7 8-bit Timer (Timer2/Timer3) with PWM generation
Two 8-bit hardware timers (Timer2 and Timer3) with PWM generation are implemented in the PMS171B. The
following descriptions thereinafter are for Timer2 only. It is because Timer3 have same structure with Timer2.
Please refer to Fig. 10 shown the hardware diagram of Timer2, the clock sources of Timer2 may come from
system clock, internal high RC oscillator (IHRC), internal low RC oscillator (ILRC), external crystal oscillator
(EOSC), PA0, PB0, PA4 and comparator result. Bit [7:4] of register tm2c is used to select the clock of Timer2. If
IHRC is selected for Timer2 clock source, the clock sent to Timer2 will keep running when using ICE in halt
state. The output of Timer2 can be sent to pin PB2(or PB0 by option code), PA3 or PB4, depending on bit [3:2]
of tm2c register. It will be a forcibly output whatever the PX.x is in input or output state. A clock pre-scaling
module is provided with divided-by- 1, 4, 16, and 64 options, controlled by bit [6:5] of tm2s register; one scaling
module with divided-by-1~31 is also provided and controlled by bit [4:0] of tm2s register. In conjunction of
pre-scaling function and scaling function, the frequency of Timer2 clock (TM2_CLK) can be wide range and
flexible.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 42 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
The Timer2 counter performs 8-bit up-counting operation only; the counter values can be set or read back by
tm2ct register. The 8-bit counter will be clear to zero automatically when its values reach for upper bound
register, the upper bound register is used to define the period of timer or duty of PWM. There are two operating
modes for Timer2: period mode and PWM mode; period mode is used to generate periodical output waveform
or interrupt event; PWM mode is used to generate PWM output waveform with optional 6-bit to 8-bit PWM
resolution, Fig. 11 shows the timing diagram of Timer2 for both period mode and PWM mode.
Fig. 10: Timer2 hardware diagram
The output of Timer3 can be sent to pin PB5, PB6 or PB7.
Time out and
Time out and
Time out and
Interrupt request
Interrupt request
Interrupt request
Counter
0xFF
bound
Counter
0xFF
Counter
0x3F
bound
bound
Time
Time
Time
Time
Time
Event Trigger
Event Trigger
Event Trigger
Output-pin
Output-pin
Output-pin
Time
Mode 0 – Period Mode
Mode 1 – 8-bit PWM Mode
Mode 1 – 6-bit PWM Mode
Fig. 11: Timing diagram of Timer2 in period mode and PWM mode (tm2c.1=1)
©Copyright 2020, PADAUK Technology Co. Ltd
Page 43 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
A Code Option GPC_PWM is for the applications which need the generated PWM waveform to be controlled by
the comparator result. If the Code Option GPC_PWM is selected, the PWM output stops while the comparator
output is 1 and then the PWM output turns on while the comparator output goes back to 0, as shown in Fig. 12.
PWM Output
Comparator
Output
Fig. 12: Comparator controls the output of PWM waveform
5.7.1 Using the Timer2 to generate periodical waveform
If periodical mode is selected, the duty cycle of output is always 50%; its frequency can be summarized as
below:
Frequency of Output = Y ÷ [2 × (K+1) × S1 × (S2+1) ]
Where,
Y = tm2c[7:4] : frequency of selected clock source
K = tm2b[7:0] : bound register in decimal
S1 = tm2s[6:5] : pre-scalar (S1= 1, 4, 16, 64)
S2 = tm2s[4:0] : scalar register in decimal (S2= 0 ~ 31)
Example 1:
tm2c = 0b0001_1000, Y=8MHz
tm2b = 0b0111_1111, K=127
tm2s = 0b0000_00000, S1=1, S2=0
frequency of output = 8MHz ÷ [ 2 × (127+1) × 1 × (0+1) ] = 31.25KHz
Example 2:
Example 3:
tm2c = 0b0001_1000, Y=8MHz
tm2b = 0b0111_1111, K=127
tm2s[7:0] = 0b0111_11111, S1=64 , S2 = 31
frequency = 8MHz ÷ ( 2 × (127+1) × 64 × (31+1) ) =15.25Hz
tm2c = 0b0001_1000, Y=8MHz
tm2b = 0b0000_1111, K=15
tm2s = 0b0000_00000, S1=1, S2=0
frequency = 8MHz ÷ ( 2 × (15+1) × 1 × (0+1) ) = 250KHz
©Copyright 2020, PADAUK Technology Co. Ltd
Page 44 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Example 4:
tm2c = 0b0001_1000, Y=8MHz
tm2b = 0b0000_0001, K=1
tm2s = 0b0000_00000, S1=1, S2=0
frequency = 8MHz ÷ ( 2 × (1+1) × 1 × (0+1) ) =2MHz
The sample program for using the Timer2 to generate periodical waveform from PA3 is shown as below:
Void FPPA0 (void)
{
. ADJUST_IC SYSCLK=IHRC/2, IHRC=16MHz, VDD=5V
…
tm2ct = 0x00;
tm2b = 0x7f;
tm2s = 0b0_00_00001;
//
//
8-bit PWM, pre-scalar = 1, scalar = 2
system clock, output=PA3, period mode
tm2c = 0b0001_10_0_0;
while(1)
{
nop;
}
}
5.7.2 Using the Timer2 to generate 8-bit PWM waveform
If 8-bit PWM mode is selected, it should set tm2c[1]=1 and tm2s[7]=0, the frequency and duty cycle of
output waveform can be summarized as below:
Frequency of Output = Y ÷ [256 × S1 × (S2+1) ]
Duty of Output = [ ( K + 1 ) ÷ 256] × 100%
Where, Y = tm2c[7:4] : frequency of selected clock source
K = tm2b[7:0] : bound register in decimal
S1= tm2s[6:5] : pre-scalar (S1= 1, 4, 16, 64)
S2 = tm2s[4:0] : scalar register in decimal (S2= 0 ~ 31)
Example 1:
tm2c = 0b0001_1010, Y=8MHz
tm2b = 0b0111_1111, K=127
tm2s = 0b0000_00000, S1=1, S2=0
frequency of output = 8MHz ÷ ( 256 × 1 × (0+1) ) = 31.25KHz
duty of output = [(127+1) ÷ 256] × 100% = 50%
©Copyright 2020, PADAUK Technology Co. Ltd
Page 45 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Example 2:
Example 3:
tm2c = 0b0001_1010, Y=8MHz
tm2b = 0b0111_1111, K=127
tm2s = 0b0111_11111, S1=64, S2=31
frequency of output = 8MHz ÷ ( 256 × 64 × (31+1) ) = 15.25Hz
duty of output = [(127+1) ÷ 256] × 100% = 50%
tm2c = 0b0001_1010, Y=8MHz
tm2b = 0b1111_1111, K=255
tm2s = 0b0000_00000, S1=1, S2=0
PWM output keep high
duty of output = [(255+1) ÷ 256] × 100% = 100%
Example 4:
tm2c = 0b0001_1010, Y=8MHz
tm2b = 0b0000_1001, K = 9
tm2s = 0b0000_00000, S1=1, S2=0
frequency of output = 8MHz ÷ ( 256 × 1 × (0+1) ) = 31.25KHz
duty of output = [(9+1) ÷ 256] × 100% = 3.9%
The sample program for using the Timer2 to generate PWM waveform from PA3 is shown as below:
void
{
FPPA0 (void)
.ADJUST_IC
SYSCLK=IHRC/2, IHRC=16MHz, VDD=5V
wdreset;
tm2ct = 0x00;
tm2b = 0x7f;
tm2s = 0b0_00_00001;
//
//
8-bit PWM, pre-scalar = 1, scalar = 2
system clock, output=PA3, PWM mode
tm2c = 0b0001_10_1_0;
while(1)
{
nop;
}
}
©Copyright 2020, PADAUK Technology Co. Ltd
Page 46 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.7.3 Using the Timer2 to generate 6-bit / 7-bit PWM waveform
If 6-bit/7-bit PWM mode is selected, it should set tm2c[1]=1 and tm2s[7]=1, the frequency and duty cycle
of output waveform can be summarized as below:
//Code options: TMX Bit = 6 bit
Frequency of Output = Y ÷ [64 × S1 × (S2+1) ]
Duty of Output = [( K+1 ) ÷ 64] × 100%
//Code options: TMX Bit = 7 bit
Frequency of Output = Y ÷ [128 × S1 × (S2+1) ]
Duty of Output = [( K+1 ) ÷ 128] × 100%
Where, tm2c[7:4] = Y : frequency of selected clock source
tm2b[7:0] = K : bound register in decimal
tm2s[6:5] = S1 : pre-scalar (S1= 1, 4, 16, 64)
tm2s[4:0] = S2 : scalar register in decimal (S2= 0 ~ 31)
Example 1:
tm2c = 0b0001_1010, Y=8MHz
tm2b = 0b0001_1111, K=31
tm2s = 0b1000_00000, S1=1, S2=0
frequency of output = 8MHz ÷ ( 64 × 1 × (0+1) ) = 125KHz
duty = [(31+1) ÷ 64] × 100% = 50%
Example 2:
tm2c = 0b0001_1010, Y=8MHz
tm2b = 0b0001_1111, K=31
tm2s = 0b1111_11111, S1=64, S2=31
frequency of output = 8MHz ÷ ( 64 × 64 × (31+1) ) = 61.03 Hz
duty of output = [(31+1) ÷ 64] × 100% = 50%
Example 3:
tm2c = 0b0001_1010, Y=8MHz
tm2b = 0b0011_1111, K=63
tm2s = 0b1000_00000, S1=1, S2=0
PWM output keep high
duty of output = [(63+1) ÷ 64] × 100% = 100%
©Copyright 2020, PADAUK Technology Co. Ltd
Page 47 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.7.4 Complementary PWM with Dead Zones
User can get complementary PWM with dead zones by employing TM2 and TM3. Here provide an
example in which duty cycle and dead time are adjustable.
//------- These two parameters need be defined when T(PWM) = 256 us ----------
#define
#define
PWM_pulse
dead_zone
70
30
// 70 us; Adjust it for a different duty cycle of TM2/TM3.
// 30 us; Adjust it for the best dead time.
//--------Parameters for switching duty cycle -----------------------------------
#define
#define
#define
PWM_Pulse_a
PWM_Pulse_b
t_delay
100 // 100 us; Adjust it for a different duty cycle of TM2/TM3
160 // 160 us; Adjust it for a different duty cycle of TM2/TM3
500 // 500 us; Switching time of duty cycle
void
{
FPPA0 (void)
// SYSCLK must quicker than Timer2’s clock. Here set SYSCLK=2MHz to capture Tm2ct = 0.
.ADJUST_IC SYSCLK=IHRC/8, IHRC=16MHz, VDD=3.3V, Init_ram;
//******Generate complementary PWM with dead zones in a fixed-duty cycle****************
//------Set the counter upper bound, duty cycle and TMXCT -----------
$ TM2S 8BIT,/4,/4
TM2B
// 16MHz /4 /4 /256 = 1MHz / 256 =
256 us
=
PWM_pulse - 1;
$ TM3S 8BIT,/4,/4
// 16MHz /4 /4 /256
TM3B
=
=
=
PWM_pulse + 2 * dead_zone - 1;
TM2CT
TM3CT
0;
0;
//------Timer PWM output control -------------------
$ TM3C
.delay
IHRC, PB5, PWM, Inverse;
dead_zone*2 - 2;
// Inverse output
// "*2": SYSCLK = 2MHz
// "-2": executing “$ TM3C XXXX” needs two
// instructions
$ TM2C
IHRC, PB4, PWM;
//***Note: Do not change the sequence of the control part’s program*****
©Copyright 2020, PADAUK Technology Co. Ltd
Page 48 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
//-------Following codes can be for reference when user needs switch duty cycle ----------
//------ Switching PWM_pulse -------------------
While (1)
{
While(tm2ct!=0)
{}
// Wait till tm2ct=0 to avoid noise
TM2B
TM3B
.delay
=
=
PWM_Pulse_a - 1;
PWM_Pulse_a + 2 * dead_zone - 1;
t_delay*2;
While(tm2ct!=0) {}
TM2B
TM3B
.delay
=
=
PWM_Pulse_b - 1;
PWM_Pulse_b + 2 * dead_zone - 1;
t_delay*2;
}
}
The following figures show the waveforms at different condition.
1. The PWM waveforms in a fixed-duty cycle:
Dead time
30us.
TM2
TM3
Fig. 13: Two complementary PWM waveforms with dead zones
©Copyright 2020, PADAUK Technology Co. Ltd
Page 49 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
2. PWM waveforms when switching two duty cycles:
Dead time 30us
TM2
TM3
Fig. 14: Two complementary PWM waveforms with dead zones
Note: This example just illustrate a method for generating complementary PWM with dead zones and
switching duty cycle. If users try to switch duty cycle by adjusting PWM_pulse: such as when the present
PWM_pulse = 70, directly let PWM_pulse_a = 100 and PWM_pulse_b = 160. Then the new value must not
be re-assigned to tm2b register until tm2ct is 0.
This method can effectively deal with the problems such as first duty cycle inaccuracy and possible
dead zone time reduction or dead zone disappear caused by assigning new value to tm2b when tm2ct is not 0.
Please handle it carefully and consult FAE when necessary according to the practical application
specifications.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 50 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.8 WatchDog Timer
The watchdog timer (WDT) is a counter with clock coming from ILRC. WDT can be cleared by power-on-reset
or by command wdreset at any time. There are four different timeout periods of watchdog timer to be chosen
by setting the misc register, it is:
8k ILRC clocks period if register misc[1:0]=00 (default)
16k ILRC clocks period if register misc[1:0]=01
64k ILRC clocks period if register misc[1:0]=10
256k ILRC clocks period if register misc[1:0]=11
The frequency of ILRC may drift a lot due to the variation of manufacture, supply voltage and temperature; user
should reserve guard band for save operation. Besides, the watchdog period will also be shorter than expected
after Reset or Wakeup events. It is suggested to clear WDT by wdreset command after these events to ensure
enough clock periods before WDT timeout.
When WDT is timeout, PMS171B will be reset to restart the program execution. The relative timing diagram of
watchdog timer is shown as Fig. 15.
VDD
t
SBP
WD
Time Out
Program
Execution
Watch Dog Time Out Sequence
Fig. 15: Sequence of Watch Dog Time Out
©Copyright 2020, PADAUK Technology Co. Ltd
Page 51 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.9 Interrupt
There are 7 interrupt lines for PMS171B:
External interrupt PA0/PB5
External interrupt PB0/PA4
ADC interrupt
Timer16 interrupt
GPC interrupt
Timer2 interrupt
Timer3 interrupt
Every interrupt request line has its own corresponding interrupt control bit to enable or disable it; the hardware
diagram of interrupt function is shown as Fig. 16. All the interrupt request flags are set by hardware and cleared
by writing intrq register. When the request flags are set, it can be rising edge, falling edge or both, depending
on the setting of register integs. All the interrupt request lines are also controlled by engint instruction (enable
global interrupt) to enable interrupt operation and disgint instruction (disable global interrupt) to disable it.
The stack memory for interrupt is shared with data memory and its address is specified by stack register sp.
Since the program counter is 16 bits width, the bit 0 of stack register sp should be kept 0. Moreover, user can
use pushaf / popaf instructions to store or restore the values of ACC and flag register to / from stack memory.
Since the stack memory is shared with data memory, the stack position and level are arranged by the compiler
in Mini-C project. When defining the stack level in ASM project, users should arrange their locations carefully to
prevent address conflicts.
Fig. 16: Hardware diagram of interrupt controller
©Copyright 2020, PADAUK Technology Co. Ltd
Page 52 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Once the interrupt occurs, its operation will be:
The program counter will be stored automatically to the stack memory specified by register sp.
New sp will be updated to sp+2.
Global interrupt will be disabled automatically.
The next instruction will be fetched from address 0x010.
During the interrupt service routine, the interrupt source can be determined by reading the intrq register.
Note: Even if INTEN=0, INTRQ will be still triggered by the interrupt source.
After finishing the interrupt service routine and issuing the reti instruction to return back, its operation will be:
The program counter will be restored automatically from the stack memory specified by register sp.
New sp will be updated to sp-2.
Global interrupt will be enabled automatically.
The next instruction will be the original one before interrupt.
User must reserve enough stack memory for interrupt, two bytes stack memory for one level interrupt and four
bytes for two levels interrupt. And so on, two bytes stack memory is for pushaf. For interrupt operation, the
following sample program shows how to handle the interrupt, noticing that it needs four bytes stack memory to
handle one level interrupt and pushaf.
void
{
FPPA0 (void)
...
$
INTEN PA0;
// INTEN =1; interrupt request when PA0 level changed
// clear INTRQ
INTRQ
ENGINT
...
=
0;
// global interrupt enable
DISGINT
...
// global interrupt disable
}
void
{
Interrupt (void)
// interrupt service routine
PUSHAF
// store ALU and FLAG register
// If INTEN.PA0 will be opened and closed dynamically,
// user can judge whether INTEN.PA0 =1 or not.
// Example: If (INTEN.PA0 && INTRQ.PA0) {…}
// If INTEN.PA0 is always enable,
// user can omit the INTEN.PA0 judgement to speed up interrupt service routine.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 53 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
If (INTRQ.PA0)
{
// Here for PA0 interrupt service routine
INTRQ.PA0 = 0;
// Delete corresponding bit (take PA0 for example)
...
}
...
// X : INTRQ = 0;
// It is not recommended to use INTRQ = 0 to clear all at the end of the
// interrupt service routine.
// It may accidentally clear out the interrupts that have just occurred
// and are not yet processed.
POPAF
// restore ALU and FLAG register
}
5.10 Power-Save and Power-Down
There are three operational modes defined by hardware: ON mode, Power-Save mode and Power-Down
modes. ON mode is the state of normal operation with all functions ON, Power-Save mode (“stopexe”) is the
state to reduce operating current and CPU keeps ready to continue, Power-Down mode (“stopsys”) is used to
save power deeply. Therefore, Power-Save mode is used in the system which needs low operating power with
wake-up periodically and Power-Down mode is used in the system which needs power down deeply with
seldom wake-up.
5.10.1 Power-Save mode (“stopexe”)
Using “stopexe” instruction to enter the Power-Save mode, only system clock is disabled, remaining all
the oscillator modules active. For CPU, it stops executing; however, for Timer16, counter keep counting
if its clock source is not the system clock. The wake-up sources for “stopexe” can be IO-toggle or
Timer16 counts to set values when the clock source of Timer16 is IHRC or ILRC modules,or wakeup by
comparator when setting GPCC.7=1 and GPCS.6=1 to enable the comparator wakeup function at the
same time. Wake-up from input pins can be considered as a continuation of normal execution, the detail
information for Power-Save mode shows below:
IHRC and EOSC oscillator modules: No change, keep active if it was enabled
ILRC oscillator modules: must remain enabled, need to start with ILRC when be wakening up
System clock: Disable, therefore, CPU stops execution
OTP memory is turned off
Timer counter: Stop counting if its clock source is system clock or the corresponding oscillator module
is disabled; otherwise, it keeps counting. (The Timer contains TM16, TM2, TM3.)
Wake-up sources:
a. IO toggle wake-up: IO toggling in digital input mode (PxC bit is 1 and PxDIER bit is 1)
©Copyright 2020, PADAUK Technology Co. Ltd
Page 54 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
b. Timer wake-up: If the clock source of Timer is not the SYSCLK, the system will be awakened
when the Timer counter reaches the set value.
c. Comparator wake-up: It need setting GPCC.7=1 and GPCS.6=1 to enable the comparator
wake-up function at the same time.
An example shows how to use Timer16 to wake-up from “stopexe”:
$ T16M
IHRC, /1, BIT8
// Timer16 setting
$ INTEGS BIT_R, xxx;
…
// BITx 0 to 1 will trigger (default)
WORD
STT16
count =
count;
0;
stopexe;
…
The initial counting value of Timer16 is zero and the system will be woken up after the Timer16 counts 256
IHRC clocks.
5.10.2 Power-Down mode (“stopsys”)
Power-Down mode is the state of deeply power-saving with turning off all the oscillator modules. By using
the “stopsys” instruction, this chip will be put on Power-Down mode directly. It is recommend to set
GPCC.7=0 to disable the comparator before the command “stopsys”. The following shows the internal
status of PMS171B detail when “stopsys” command is issued:
All the oscillator modules are turned off
OTP memory is turned off
The contents of SRAM and registers remain unchanged
Wake-up sources: IO toggle in digital mode (PxDIER bit is 1)
Wake-up from input pins can be considered as a continuation of normal execution. To minimize power
consumption, all the I/O pins should be carefully manipulated before entering power-down mode. The
reference sample program for power down is shown as below:
CLKMD
CLKMD.4
…
=
=
0xF4;
0;
//
//
Change clock from IHRC to ILRC
disable IHRC
while (1)
{
STOPSYS;
//
//
//
enter power-down
if (…) break;
if wakeup happen and check OK, then return to high speed,
else stay in power-down mode again.
}
CLKMD
=
0x34;
//
Change clock from ILRC to IHRC/2
©Copyright 2020, PADAUK Technology Co. Ltd
Page 55 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.10.3 Wake-up
After entering the Power-Down or Power-Save modes, the PMS171B can be resumed to normal operation
by toggling IO pins. Wake-up from timer and comparator are available for Power-Save mode ONLY. Table
15 shows the differences in wake-up sources between STOPSYS and STOPEXE.
Differences in wake-up sources between STOPSYS and STOPEXE
IO Toggle
Yes
Timer wake-up
comparator
No
STOPSYS
STOPEXE
No
Yes
Yes
Yes
Table 5: Differences in wake-up sources between Power-Save mode and Power-Down mode
When using the IO pins to wake-up the PMS171B, registers padier should be properly set to enable the
wake-up function for every corresponding pin. The time for normal wake-up is about 3000 ILRC clocks
counting from wake-up event; fast wake-up can be selected to reduce the wake-up time by misc register,
and the time for fast wake-up is about 45 ILRC clocks from IO toggling. Besides, the wake up function in
GPCS controls the comparator.
Suspend mode
STOPEXE suspend
or
Wake-up mode
Wake-up time (tWUP) from IO toggle
45 * TILRC,
Fast wake-up
Where TILRC is the time period of ILRC
STOPSYS suspend
STOPEXE suspend
or
3000 * TILRC
,
Normal wake-up
Where TILRC is the clock period of ILRC
STOPSYS suspend
Please notice that when Code Option is set to Fast boot-up, no matter which wake-up mode is selected in
misc.5, the wake-up mode will be forced to be FAST. If Normal boot-up is selected, the wake-up mode is
determined by misc.5.
5.11 IO Pins
All the pins can be independently set into two states output or input by configuring the data registers (pa, pb),
control registers (pac, pbc) and pull-high registers (paph, pbph). Two pins of them, PB3 & PB6, have
additional pull-low registers (pbpl.3, pbpl.6)Port B[6] and Port B[3] also set into input with pull-low by
configuring the control register (pbc) and pull- low register (pbpl). All these pins have Schmitt-trigger input
buffer and output driver with CMOS level. When it is set to output low, the pull-up resistor is turned off
automatically. When it is set to output high, the pull-low resistor is turned off automatically. If user wants to
read the pin state, please notice that it should be set to input mode before reading the data port; if user reads
the data port when it is set to output mode, the reading data comes from data register, NOT from IO pad. As an
example, Table 6 shows the configuration table of bit 0 of port A. The hardware diagram of IO buffer is also
shown as Fig. 17. Table 7 shows the configuration table of bit 6 of port B. The hardware diagram of IO buffer is
also shown as Fig. 18.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 56 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
pa.0 pac.0 paph.0
Description
Input without pull-up resistor
X
X
0
1
0
0
1
1
0
1
X
0
Input with pull-up resistor
Output low without pull-up resistor
Output high without pull-up resistor
Table 6: PA0 Configuration Table
pb.6 pbc.6 pbph.6 pbpl.6
Description
X
X
X
0
0
0
0
0
1
0
1
0
Input without pull-high / pull-low resistor
Input with pull-low resistor
Input with pull-high resistor
Input with both pull-high and pull-low resistor
(Note for the current consumption)
Output low without pull resistor
Output high without pull resistor
X
0
1
1
0
1
1
1
X
X
X
X
Table 7: PB6 Configuration Table
Fig. 17: Hardware diagram of IO buffer with Weak Pull High PMOS
©Copyright 2020, PADAUK Technology Co. Ltd
Page 57 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Fig. 18: Hardware diagram of IO buffer with Weak Pull High PMOS & Weak Pull Low NMOS
One thing should be noted, PA5 and PB0 can be open-drain ONLY when setting to output mode (without Q1).
And by the way, there is a code option PB4_PB5_Drive for PB4 and PB5 to select their drive and sink current.
PB0 and PB7 provide super large current NMOS and PMOS output respectively.
The corresponding bits in registers padier / pbdier should be set to low to prevent leakage current for those
pins are selected to be analog function. When PMS171B is put in power-down or power-save mode, every pin
can be used to wake-up system by toggling its state. Therefore, those pins needed to wake-up system must be
set to input mode and set the corresponding bits of registers padier and pbdier to high. The same reason,
padier.0 should be set high when PA0 is used as external interrupt pin, and so for other external interrupt pins:
PB0, PA4 and PB5.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 58 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.12 Reset and LVR
5.12.1 Reset
There are many causes to reset the PMS171B, once reset is asserted, most of all the registers in
PMS171B will be set to default values, system should be restarted once abnormal cases happen, or by
jumping program counter to address 0x0. The data memory is in uncertain state when reset comes from
power-up and LVR; however, the content will be kept when reset comes from PRSTB pin or WDT timeout.
5.12.2 LVR reset
By code option, there are many different levels of LVR for reset; usually, user selects LVR reset level to be
in conjunction with operating frequency and supply voltage.
5.13 Analog-to-Digital Conversion (ADC) module
Fig. 19: ADC Block Diagram
©Copyright 2020, PADAUK Technology Co. Ltd
Page 59 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
There are 6 registers when using the ADC module, which are:
ADC Control Register (adcc)
ADC Regulator Control Register (adcrgc)
ADC Mode Register (adcm)
ADC Result Register (adcr)
Port A/B Digital Input Enable Register (padier, pbdier)
The following steps are required to do the AD conversion procedure:
(1) Configure the voltage reference high by adcrgc register
(2) Configure the AD conversion clock by adcm register
(3) Configure the pin as analog input by padier, pbdier register
(4) Select the ADC input channel by adcc register
(5) Enable the ADC module by adcc register
(6) Execute the AD conversion and check if ADC data is ready.
Set ‘1’ to addc.6 to start the conversion and check whether addc.6 is ‘1’.
(7) Read the ADC result registers:
5.13.1 The input requirement for AD conversion
For the AD conversion to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed
to fully charge to the voltage reference high level and discharge to the voltage reference low level. The
analog input model is shown as Fig. 20, the signal driving source impedance (Rs) and the internal sampling
switch impedance (Rss) will affect the required time to charge the capacitor CHOLD directly. The internal
sampling switch impedance may vary with ADC supply voltage; the signal driving source impedance will
affect accuracy of analog input signal. User must ensure the measured signal is stable before sampling;
therefore, the maximum signal driving source impedance is highly dependent on the frequency of signal to
be measured. The recommended maximum impedance for analog driving source is about 10KΩ under
500KHz input frequency.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 60 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Fig.20: Analog Input Model
Before starting the AD conversion, the minimum signal acquisition time should be met for the selected
analog input signal, the selection of ADCLK must be met the minimum signal acquisition time.
5.13.2 Select the reference high voltage
The ADC reference high voltage can be selected via bit[7] of register adcrgc and its option can be VDD or
PB1 from external pin.
5.13.3 ADC clock selection
The clock of ADC module (ADCLK) can be selected by adcm register; there are 8 possible options for
ADCLK from CLK÷1 to CLK÷128 (CLK is the system clock). Due to the signal acquisition time TACQ is one
clock period of ADCLK, the ADCLK must meet that requirement. The recommended ADC clock is to
operate at 2us.
5.13.4 Configure the analog pins
There are 11 analog signals can be selected for AD conversion, 10 analog input signals come from
external pins and one is from internal bandgap reference voltage 1.2V. For external pins, the analog
signals are shared with Port A[0], Port A[3], Port A[4], and Port B[7:1]. To avoid leakage current at the
digital circuit, those pins defined for analog input should disable the digital input function (set the
corresponding bit of padier or pbdier register to be 0).
The measurement signals of ADC belong to small signal; it should avoid the measured signal to be
interfered during the measurement period, the selected pin should:
(1) be set to input mode
(2) turn off weak pull-high and pull-low resistor
(3) set the corresponding pin to analog input by port A/B digital input disable register (padier / pbdier).
©Copyright 2020, PADAUK Technology Co. Ltd
Page 61 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.13.5 Using the ADC
The following example shows how to use ADC with PB0~PB3.
First, defining the selected pins:
PBC
=
=
=
=
0B_XXXX_0000;
0B_XXXX_0000;
0B_XXXX_0_XXX;
0B_XXXX_0000;
//
//
//
//
PB0 ~ PB3 as Input
PB0 ~ PB3 without pull-high
PB3 without pull-low
PBPH
PBPL
PBDIER
PB0 ~ PB3 digital input is disabled
Next, setting ADCC register, example as below:
$
$
$
ADCC Enable, PB3;
ADCC Enable, PB2;
ADCC Enable, PB0;
//
//
//
set PB3 as ADC input
set PB2 as ADC input
set PB0 as ADC input
Next, setting ADCM and ADCRGC register, example as below:
$
$
$
ADCM 8BIT, /16;
ADCM 8BIT, /8;
ADCRGC VDD;
//
//
recommend /16 @System Clock=8MHz
recommend /8 @System Clock=4MHz
Then, start the ADC conversion:
AD_START =
while(!AD_DONE) NULL;
1;
//
//
start ADC conversion
wait ADC conversion result
Finally, it can read ADC result when AD_DONE is high:
BYTE
Data
Data;
ADCR
//
One byte result: ADCR
=
The ADC can be disabled by using the following method:
ADCC Disable;
$
or
ADCC
=
0;
©Copyright 2020, PADAUK Technology Co. Ltd
Page 62 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
5.13.6 How to calculate ADC input voltage VIN
For PMS171B, only VDD but not 1.2V band-gap voltage can be selected as the VREF of the ADC. When
VDD is not regulated, users have to use the reading of 1.2V band-gap voltage to deduce the input voltage
(VIN) by the ratio of the readings. The principle is as below:
VBG / VDD = NBG / 256 ....(1)
VIN / VDD = NIN / 256
Where VIN is the analog input voltage
BG is the 1.2V band-gap voltage
....(2)
V
NIN is the corresponding ADC reading of VIN
NBG is the corresponding ADC reading of VBG
VDD is the VDD at the measuring instant
256 is the full swing reading when VIN=VDD (8bit: 28 = 256)
(2)/(1) we get
VIN/VBG = NIN/NBG
And so
VIN = NIN / NBG *VBG
It means users can firstly get the readings for VIN and VBG respectively in a very short period that VDD
remains unchanged. And then use multiplication and division program module or use look-up table
method to finally get the VIN voltage.
If necessary, please contact FAE for demo code reference.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 63 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
6. IO Registers
6.1. ACC Status Flag Register (flag), IO address = 0x00
Bit Reset
R/W
Description
7 - 4
3
-
-
Reserved. Please do not use.
0
R/W
OV (Overflow Flag). This bit is set to be 1 whenever the sign operation is overflow.
AC (Auxiliary Carry Flag). There are two conditions to set this bit, the first one is carry out
of low nibble in addition operation and the other one is borrow from the high nibble into low
nibble in subtraction operation.
2
0
R/W
C (Carry Flag). There are two conditions to set this bit, the first one is carry out in addition
operation, and the other one is borrow in subtraction operation. Carry is also affected by
shift with carry instruction.
1
0
0
0
R/W
R/W
Z (Zero Flag). This bit will be set when the result of arithmetic or logic operation is zero;
Otherwise, it is cleared.
6.2. Stack Pointer Register (sp), IO address = 0x02
Bit Reset R/W
Description
Stack Pointer Register. Read out the current stack pointer, or write to change the stack
pointer. Please notice that bit 0 should be kept 0 due to program counter is 16 bits.
7 - 0 R/W
-
6.3. Clock Mode Register (clkmd), IO address = 0x03
Bit Reset R/W
Description
System clock (CLK) selection:
Type 0, clkmd[3]=0 Type 1, clkmd[3]=1
000: IHRC÷4
000: IHRC÷16
001: IHRC÷2
001: IHRC÷8
010: reserved
010: ILRC÷16 (ICE does NOT Support.)
011: IHRC÷32
7 - 5
111
R/W
011: EOSC÷4
100: EOSC÷2
100: IHRC÷64
101: EOSC
101: EOSC÷8
110: ILRC÷4
11x: reserved
111: ILRC (default)
Internal High RC Enable. 0 / 1: disable / enable
4
3
1
0
R/W
R/W
Clock Type Select. This bit is used to select the clock type in bit [7:5].
0 / 1: Type 0 / Type 1
Internal Low RC Enable. 0 / 1: disable / enable
If ILRC is disabled, watchdog timer is also disabled.
Watch Dog Enable. 0 / 1: disable / enable
2
1
R/W
1
0
1
0
R/W
R/W
Pin PA5/PRSTB function. 0 / 1: PA5 / PRSTB
©Copyright 2020, PADAUK Technology Co. Ltd
Page 64 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
6.4. Interrupt Enable Register (inten), IO address = 0x04
Bit
7
Reset
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Description
Enable interrupt from Timer3. 0 / 1: disable / enable
Enable interrupt from Timer2. 0 / 1: disable / enable
Reserved.
0
0
0
0
0
0
0
0
6
5
4
Enable interrupt from comparator: disable / enable
Enable interrupt from ADC. 0 / 1: disable / enable
Enable interrupt from Timer16 overflow. 0 / 1: disable / enable
Enable interrupt from PB0/PA4. 0 / 1: disable / enable
Enable interrupt from PA0/PB5. 0 / 1: disable / enable
3
2
1
0
6.5. Interrupt Request Register (intrq), IO address = 0x05
Bit
Reset
R/W
Description
Interrupt Request from Timer3, this bit is set by hardware and cleared by software.
0 / 1: No request / Request
7
-
R/W
Interrupt Request from Timer2, this bit is set by hardware and cleared by software.
0 / 1: No request / Request
6
5
4
-
-
-
R/W
R/W
R/W
Reserved.
Interrupt Request from comparator, this bit is set by hardware and cleared by software.
0 / 1: No request / Request
Interrupt Request from ADC, this bit is set by hardware and cleared by software.
0 / 1: No request / Request
3
2
1
0
-
-
-
-
R/W
R/W
R/W
R/W
Interrupt Request from Timer16, this bit is set by hardware and cleared by software.
0 / 1: No request / Request
Interrupt Request from pin PB0/PA4, this bit is set by hardware and cleared by software.
0 / 1: No request / Request
Interrupt Request from pin PA0/PB5, this bit is set by hardware and cleared by software.
0 / 1: No Request / request
©Copyright 2020, PADAUK Technology Co. Ltd
Page 65 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
6.6. Timer16 mode Register (t16m), IO address = 0x06
Bit
Reset R/W
Description
Timer16 Clock source selection.
000: disable
001: CLK (system clock)
010: reserved
7 - 5
000
R/W
R/W
R/W
011: PA4 falling edge (from external pin)
100: IHRC
101: EOSC
110: ILRC
111: PA0 falling edge (from external pin)
Timer16 clock pre-divider.
00: ÷1
4 - 3
00
01: ÷4
10: ÷16
11: ÷64
Interrupt source selection. Interrupt event happens when the selected bit status is changed.
0 : bit 8 of Timer16
1 : bit 9 of Timer16
2 : bit 10 of Timer16
3 : bit 11 of Timer16
4 : bit 12 of Timer16
5 : bit 13 of Timer16
6 : bit 14 of Timer16
7 : bit 15 of Timer16
2 - 0
000
6.7. Timer2 Bound Register (tm2b), IO address = 0x09
Bit
Reset R/W
0x00 WO
Description
7 - 0
Timer2 bound register.
6.8. External Oscillator setting Register (eoscr), IO address = 0x0a
Bit
Reset R/W
Description
7
0
WO
Enable external crystal oscillator. 0 / 1 : Disable / Enable
External crystal oscillator selection.
00 : reserved
6 - 5
00
WO
01 : low driving capability, for lower frequency, ex: 32KHz crystal oscillator
10 : middle driving capability, for middle frequency, ex: 1MHz crystal oscillator
11 : high driving capability, for higher frequency, ex: 4MHz crystal oscillator
Reserved. Please keep 0 for future compatibility.
4 - 1
0
-
-
0
WO
Power-down the Bandgap and LVR hardware modules. 0 / 1: normal / power-down
©Copyright 2020, PADAUK Technology Co. Ltd
Page 66 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
6.9. Interrupt Edge Select Register (integs), IO address = 0x0c
Bit
Reset
R/W
Description
7 - 5
-
-
Reserved.
Timer16 edge selection.
4
0
WO 0 : rising edge of the selected bit to trigger interrupt
1 : falling edge of the selected bit to trigger interrupt
PB0/PA4 edge selection.
00: both rising edge and falling edge of the selected bit to trigger interrupt
WO 01: rising edge of the selected bit to trigger interrupt
10: falling edge of the selected bit to trigger interrupt
11: reserved.
3 - 2
00
PA0/PB5 edge selection.
00 : both rising edge and falling edge of the selected bit to trigger interrupt
WO 01 : rising edge of the selected bit to trigger interrupt
10 : falling edge of the selected bit to trigger interrupt
11 : reserved.
1 - 0
00
6.10.Port A Digital Input Enable Register (padier), IO address = 0x0d
Bit
Reset
R/W
Description
Enable PA7 digital input and wake-up event. 1 / 0 : enable / disable
7
1
WO
This bit should be set to low to prevent leakage current when external crystal oscillator is
used. If this bit is set to low, PA7 can NOT be used to wake-up the system.
Enable PA6 digital input and wake-up event. 1 / 0 : enable / disable
6
5
4
1
1
1
WO
WO
WO
This bit should be set to low to prevent leakage current when external crystal oscillator is
used. If this bit is set to low, PA6 can NOT be used to wake-up the system.
Enable PA5 digital input and wake-up event. 1 / 0 : enable / disable
This bit can be set to low to disable wake-up from PA5 toggling.
Enable PA4 digital input and wake-up event and interrupt request. 1 / 0 : enable / disable
This bit can be set to low to prevent leakage current when PA4 is assigned as AD input,
and to disable wake-up from PA0 toggling and interrupt request from this pin.
Enable PA3 digital input and wake-up event. 1 / 0 : enable / disable
3
2 - 1
0
1
1
1
WO
WO
WO
This bit should be set to low when PA3 is assigned as AD input to prevent leakage current.
If this bit is set to low, PA3 can NOT be used to wake-up the system.
Reserved
Enable PA0 digital input and wake-up event and interrupt request. 1 / 0 : enable / disable
This bit can be set to low to prevent leakage current when PA0 is assigned as AD input,
and to disable wake-up from PA0 toggling and interrupt request from this pin.
6.11.Port B Digital Input Enable Register (pbdier), IO address = 0x0e
Bit
Reset R/W
Description
Enable PB7~PB0 digital input and wake-up event and interrupt request.
1 / 0 : enable / disable
These bits can be set to low to prevent leakage current when PB7~PB1 are assigned as AD
inputs. When disable is selected, the wakeup function and interrupt requests from bit5 or bit0
are also disabled.
7 - 0
0xFF
WO
©Copyright 2020, PADAUK Technology Co. Ltd
Page 67 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
6.12. Port A Data Register (pa), IO address = 0x10
Bit
Reset R/W
0x00 R/W Data register for Port A.
Description
7 - 0
6.13. Port A Control Register (pac), IO address = 0x11
Bit
Reset R/W
Description
Port A control registers. This register is used to define input mode or output mode for each
corresponding pin of port A. 0 / 1: input / output
7 - 0
0x00
R/W
Please note that PA5 can be INPUT or OUTPUT LOW ONLY, the output state will be
tri-state when PA5 is programmed into output mode with data 1.
6.14. Port A Pull-High Register (paph), IO address = 0x12
Bit
Reset R/W
Description
Port A pull-high register. This register is used to enable the internal pull-high device on each
7 - 0 0x00 R/W corresponding pin of port A and this pull high function is active only for input mode.
0 / 1 : disable / enable
6.15. Port B Data Register (pb), IO address = 0x14
Bit
Reset R/W
0x00 R/W Data register for Port B.
Description
7 - 0
6.16. Port B Control Register (pbc), IO address = 0x15
Bit
Reset R/W
Description
Port B control register. This register is used to define input mode or output mode for each
corresponding pin of port B. 0 / 1: input / output
7 - 0
0x00 R/W
6.17. Port B Pull-High Register (pbph), IO address = 0x16
Bit
7 - 1
0
Reset R/W
Description
Port B[7:1] pull-high register. This register is used to enable the internal pull-high device on
each corresponding pin of port B and this pull high function is active only for input mode.
0 / 1 : disable / enable
0x00
-
R/W
-
Reserved.
6.18. Port B Pull Low Register (pbpl), IO address = 0x38
Bit
7
Reset
R/W
Description
-
0
-
-
R/W
-
Reserved.
6
PB6 Pull Low enable. 0/1: Disable/ Enable
Reserved.
5 - 4
3
0
-
R/W
-
PB3 Pull Low enable. 0/1: Disable/ Enable
Reserved.
2- 0
Notice: ICE does NOT support.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 68 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
6.19. Miscellaneous Register (misc), IO address = 0x17
Bit
Reset
R/W
Description
Reserved. (keep 0 for future compatibility)
7 - 6
-
-
Enable fast Wake-up. Fast wake-up is NOT supported when EOSC is enabled.
0: Normal wake-up.
The wake-up time is 3000 ILRC clocks (Not for fast boot-up)
5
0
WO 1: Fast wake-up.
The wake-up time is 45 ILRC clocks + oscillator stable time.
If wake-up from STOPEXE suspend, there is no oscillator stable time;
If wake-up from STOPSYS suspend, it will be IHRC or ILRC stable time from power-on.
Reserved. (keep 0 for future compatibility)
Disable LVR function.
4 - 3
2
-
-
0
WO
0 / 1 : Enable / Disable
Watch dog time out period.
00: 8k ILRC clock period
1 - 0
00
WO 01: 16k ILRC clock period
10: 64k ILRC clock period
11: 256k ILRC clock period
6.20. Comparator Control Register (gpcc), IO address = 0x18
Bit
Reset
R/W
Description
Enable comparator.
0 / 1 : disable / enable
7
0
R/W
When this bit is set to enable, please also set the corresponding analog input pins to be
digital disable to prevent IO leakage.
Comparator result of comparator.
6
5
4
-
RO
0: plus input < minus input
1: plus input > minus input
Select whether the comparator result output will be sampled by TM2_CLK?
0
0
R/W 0: result output NOT sampled by TM2_CLK
1: result output sampled by TM2_CLK
Inverse the polarity of result output of comparator.
R/W 0: polarity is NOT inversed.
1: polarity is inversed.
Selection the minus input (-) of comparator.
000 : PA3
001 : PA4
010 : Internal 1.20 volt bandgap reference voltage
3 - 1
000
R/W
011 : Vinternal R
100 : PB6 (NOT for ICE)
101 : PB7 (NOT for ICE)
11X: reserved
0
0
R/W Selection the plus input (+) of comparator. 0/1: Vinternal R / PA4
©Copyright 2020, PADAUK Technology Co. Ltd
Page 69 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
6.21. Comparator Selection Register (gpcs), IO address = 0x19
Bit
Reset
R/W
Description
Comparator output enable (to PA0).
0 / 1 : Disable / Enable
7
0
WO
Wakeup by comparator enable. (The comparator wakeup effectively when gpcc.6 electrical
WO level changed)
0 / 1 : disable / enable
6
0
5
4
0
0
WO Selection of high range of comparator.
WO Selection of low range of comparator.
Selection the voltage level of comparator.
3 - 0
0000
WO
0000 (lowest) ~ 1111 (highest)
6.22. Timer2 Control Register (tm2c), IO address = 0x1c
Bit
Reset
R/W
Description
Timer2 clock selection.
0000 : disable
0001 : CLK (system clock)
0010 : IHRC or IHRC *2 (by code option TMx_source)
0011 : EOSC
0100 : ILRC
0101 : comparator output
011x : reserved
7 - 4
0000
R/W
1000 : PA0 (rising edge)
1001 : ~PA0 (falling edge)
1010 : PB0 (rising edge)
1011 : ~PB0 (falling edge)
1100 : PA4 (rising edge)
1101 : ~PA4 (falling edge)
Notice: In ICE mode and IHRC is selected for Timer2 clock, the clock sent to Timer2 does
NOT be stopped, Timer2 will keep counting when ICE is in halt state.
Timer2 output selection.
00 : disable
3 - 2
00
R/W 01 : PB2 or PB0 (by code option TM2 Output) (ICE doesn’t support PB0.)
10 : PA3
11 : PB4
Timer2 mode selection.
R/W
1
0
0
0
0 / 1 : period mode / PWM mode
Enable to inverse the polarity of Timer2 output.
R/W
0 / 1: disable / enable
©Copyright 2020, PADAUK Technology Co. Ltd
Page 70 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
6.23. Timer2 Counter Register (tm2ct), IO address = 0x1d
Bit
Reset R/W
0x00 R/W Bit [7:0] of Timer2 counter register.
Description
7 - 0
6.24. Timer2 Scalar Register (tm2s), IO address = 0x1e
Bit
Reset R/W
Description
PWM resolution selection.
0 : 8-bit
7
0
WO
1 : 6-bit or 7-bit (by code option TMx_bit)
Timer2 clock pre-scalar.
00 : ÷ 1
6 - 5
00
WO
WO
01 : ÷ 4
10 : ÷ 16
11 : ÷ 64
4 - 0 00000
Timer2 clock scalar.
6.25. Timer3 Control Register (tm3c), IO address = 0x32
Bit
Reset
R/W
Description
Timer3 clock selection.
0000 : disable
0001 : CLK (system clock)
0010 : IHRC or IHRC *2 (by code option TMx_source)
0011 : EOSC
0100 : ILRC
0101 : comparator output
011x : reserved
7 - 4
0000
R/W
1000 : PA0 (rising edge)
1001 : ~PA0 (falling edge)
1010 : PB0 (rising edge)
1011 : ~PB0 (falling edge)
1100 : PA4 (rising edge)
1101 : ~PA4 (falling edge)
Notice: In ICE mode and IHRC is selected for Timer3 clock, the clock sent to Timer3 does
NOT be stopped, Timer3 will keep counting when ICE is in halt state.
Timer3 output selection.
00 : disable
3 - 2
00
R/W 01 : PB5
10 : PB6
11 : PB7
Timer3 mode selection.
1
0
0
0
R/W
R/W
0 / 1 : period mode / PWM mode
Enable to inverse the polarity of Timer3 output.
0 / 1: disable / enable
©Copyright 2020, PADAUK Technology Co. Ltd
Page 71 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
6.26. Timer3 Counter Register (tm3ct), IO address = 0x33
Bit
Reset
R/W
Description
7 - 0
0x00
R/W
Bit [7:0] of Timer3 counter register.
6.27. Timer3 Scalar Register (tm3s), IO address = 0x34
Bit
Reset
R/W
Description
PWM resolution selection.
0 : 8-bit
7
0
WO
1 : 6-bit or 7bit (by code option TMx_bit)
Timer3 clock pre-scalar.
00 : ÷ 1
6 - 5
4 - 0
00
WO
WO
01 : ÷ 4
10 : ÷ 16
11 : ÷ 64
00000
Timer3 clock scalar.
6.28. Timer3 Bound Register (tm3b), IO address = 0x3f
Bit
Reset
R/W
Description
7 - 0
0x00
WO
Timer3 bound register.
6.29. ADC Control Register (adcc), IO address = 0x3b
Bit
Reset
R/W
Description
Enable ADC function. 0/1: Disable/Enable.
7
0
R/W
ADC process control bit.
6
0
R/W
Read “1” to indicate the ADC is ready.
Channel selector. These four bits are used to select input signal for AD conversion.
0000: reserved,
0001: PB1,
0010: PB2,
0011: PB3,
0100: PB4,
0101: PB5,
5 - 2
0001
R/W
0110: PB6,
0111: PB7,
1000: PA3,
1001: PA4,
1010: PA0,
1111: (Channel F) Bandgap reference voltage 1.2V
Others: reserved
Reserved. (keep 0 for future compatibility)
0 - 1
-
-
©Copyright 2020, PADAUK Technology Co. Ltd
Page 72 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
6.30. ADC Mode Register (adcm), IO address = 0x3c
Bit
Reset
R/W
Description
Reserved (keep 0 for future compatibility)
7 - 4
-
-
ADC clock source selection.
000: CLK (system clock) ÷ 1,
001: CLK (system clock) ÷ 2,
010: CLK (system clock) ÷ 4,
3 - 1
000
R/W 011: CLK (system clock) ÷ 8,
100: CLK (system clock) ÷ 16,
101: CLK (system clock) ÷ 32,
110: CLK (system clock) ÷ 64,
111: CLK (system clock) ÷ 128,
0
-
-
Reserved
6.31. ADC Regulator Control Register (adcrgc), IO address = 0x3d
Bit
Reset
R/W
Description
ADC reference high voltage.
WO 0: VDD,
1: External PIN (PB1)
Reserved.
7
0
-
6 - 0
-
6.32. ADC Result High Register (adcr), IO address = 0x3e
Bit
Reset
R/W
Description
7 - 0
-
RO
These eight read-only bits will be the bit [7:0] of ADC conversion result.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 73 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
7. Instructions
Symbol
Description
ACC
a
Accumulator (Abbreviation of accumulator)
Accumulator (symbol of accumulator in program)
sp
flag
I
Stack pointer
ACC status flag register
Immediate data
&
Logical AND
|
Logical OR
←
^
Movement
Exclusive logic OR
+
Add
-
〜
〒
OV
Z
Subtraction
NOT (logical complement, 1’s complement)
NEG (2’s complement)
Overflow (The operational result is out of range in signed 2’s complement number system)
Zero (If the result of ALU operation is zero, this bit is set to 1)
Carry (The operational result is to have carry out for addition or to borrow carry for subtraction in
unsigned number system)
C
Auxiliary Carry
AC
(If there is a carry out from low nibble after the result of ALU operation, this bit is set to 1)
Program counter for CPU
pc0
M.n
Only addressed in 0~0x3F (0~63) is allowed
©Copyright 2020, PADAUK Technology Co. Ltd
Page 74 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
7.1. Data Transfer Instructions
mov
mov
mov
mov
mov
a, I
Move immediate data into ACC.
Example: mov a, 0x0f;
Result: a ← 0fh;
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
M, a
a, M
Move data from ACC into memory
Example: mov
MEM, a;
Result: MEM ← a
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Move data from memory into ACC
Example: mov
a, MEM ;
Result: a ← MEM; Flag Z is set when MEM is zero.
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
a, IO
Move data from IO into ACC
Example: mov
a, pa ;
Result: a ← pa; Flag Z is set when pa is zero.
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
IO, a
Move data from ACC into IO
Example: mov
Result: pb ← a
pb, a;
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Move 16-bit counting values in Timer16 to memory in word.
Example: ldt16 word;
ldt16 word
Result:
word ← 16-bit timer
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Application Example:
------------------------------------------------------------------------------------------------------------------------
word
…
T16val ;
// declare a RAM word
clear
clear
stt16
…
lb@ T16val ;
hb@ T16val ;
T16val ;
// clear T16val (LSB)
// clear T16val (MSB)
// initial T16 with 0
set1
…
t16m.5 ;
// enable Timer16
set0
ldt16
….
t16m.5 ;
T16val ;
// disable Timer 16
// save the T16 counting value to T16val
------------------------------------------------------------------------------------------------------------------------
Store 16-bit data from memory in word to Timer16.
Example: stt16 word;
stt16 word
Result:
16-bit timer ←word
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
©Copyright 2020, PADAUK Technology Co. Ltd
Page 75 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Application Example:
------------------------------------------------------------------------------------------------------------------------
word
…
T16val ;
// declare a RAM word
mov
mov
mov
mov
stt16
…
a, 0x34 ;
lb@ T16val , a ; // move 0x34 to T16val (LSB)
a, 0x12 ;
hb@ T16val , a ; // move 0x12 to T16val (MSB)
T16val ;
// initial T16 with 0x1234
----------------------------------------------------------------------------------------------------------------------
idxm a, index Move data from specified memory to ACC by indirect method. It needs 2T to execute this
instruction.
Example: idxm a, index;
Result:
a ← [index], where index is declared by word.
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Application Example:
-----------------------------------------------------------------------------------------------------------------------
word
…
RAMIndex ;
// declare a RAM pointer
mov
mov
mov
mov
…
a, 0x5B ;
// assign pointer to an address (LSB)
// save pointer to RAM (LSB)
lb@RAMIndex, a ;
a, 0x00 ;
// assign 0x00 to an address (MSB), should be 0
hb@RAMIndex, a ; // save pointer to RAM (MSB)
idxm
a, RAMIndex ; // move memory data in address 0x5B to ACC
------------------------------------------------------------------------------------------------------------------------
Idxm index, a Move data from ACC to specified memory by indirect method. It needs 2T to execute this
instruction.
Example: idxm index, a;
Result:
[index] ← a; where index is declared by word.
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Application Example:
------------------------------------------------------------------------------------------------------------------------
word
…
RAMIndex ;
// declare a RAM pointer
mov
mov
mov
mov
…
a, 0x5B ;
// assign pointer to an address (LSB)
// save pointer to RAM (LSB)
lb@RAMIndex, a ;
a, 0x00 ;
// assign 0x00 to an address (MSB), should be 0
hb@RAMIndex, a ; // save pointer to RAM (MSB)
mov
idxm
a, 0xA5 ;
RAMIndex, a ;
// move 0xA5 to memory in address 0x5B
------------------------------------------------------------------------------------------------------------------------
©Copyright 2020, PADAUK Technology Co. Ltd
Page 76 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
xch
M
Exchange data between ACC and memory.
Example: xch MEM ;
Result:
MEM ← a , a ← MEM
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Move the ACC and flag register to memory that address specified in the stack pointer.
Example: pushaf;
pushaf
Result:
[sp] ← {flag, ACC};
sp ← sp + 2 ;
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Application Example:
------------------------------------------------------------------------------------------------------------------------
.romadr 0x10 ;
// ISR entry address
pushaf ;
…
// put ACC and flag into stack memory
// ISR program
…
// ISR program
popaf ;
reti ;
// restore ACC and flag from stack memory
------------------------------------------------------------------------------------------------------------------------
Restore ACC and flag from the memory which address is specified in the stack pointer.
Example: popaf;
popaf
Result:
sp ← sp - 2
{Flag, ACC} ← [sp] ;
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
;
7.2. Arithmetic Operation Instructions
add
add
add
a, I
Add immediate data with ACC, then put result into ACC.
Example: add a, 0x0f ;
Result: a ← a + 0fh
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
a, M
M, a
Add data in memory with ACC, then put result into ACC.
Example: add
a, MEM ;
Result: a ← a + MEM
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
Add data in memory with ACC, then put result into memory.
Example: add
MEM, a;
Result: MEM ← a + MEM
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
addc a, M
addc M, a
Add data in memory with ACC and carry bit, then put result into ACC.
Example: addc
a, MEM ;
Result: a ← a + MEM + C
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
Add data in memory with ACC and carry bit, then put result into memory.
Example: addc
Result: MEM ← a + MEM + C
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
MEM, a ;
©Copyright 2020, PADAUK Technology Co. Ltd
Page 77 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
addc
addc
sub
a
Add carry with ACC, then put result into ACC.
Example: addc a ;
Result: a ← a + C
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
M
Add carry with memory, then put result into memory.
Example: addc
MEM ;
Result: MEM ← MEM + C
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
a, I
a, M
M, a
Subtraction immediate data from ACC, then put result into ACC.
Example: sub
a, 0x0f;
Result: a ← a - 0fh ( a + [2’s complement of 0fh] )
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
sub
Subtraction data in memory from ACC, then put result into ACC.
Example: sub
a, MEM ;
Result: a ← a - MEM ( a + [2’s complement of M] )
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
sub
Subtraction data in ACC from memory, then put result into memory.
Example: sub
MEM, a;
Result: MEM ← MEM - a ( MEM + [2’s complement of a] )
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
subc a, M
subc M, a
Subtraction data in memory and carry from ACC, then put result into ACC.
Example: subc
a, MEM;
Result: a ← a – MEM - C
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
Subtraction ACC and carry bit from memory, then put result into memory.
Example: subc
MEM, a ;
Result: MEM ← MEM – a - C
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
subc
subc
a
Subtraction carry from ACC, then put result into ACC.
Example: subc
a;
Result: a ← a - C
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
M
Subtraction carry from the content of memory, then put result into memory.
Example: subc
MEM;
Result: MEM ← MEM - C
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
inc
M
Increment the content of memory.
Example: inc
MEM ;
Result: MEM ← MEM + 1
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
Decrement the content of memory.
dec
M
Example: dec
MEM;
Result: MEM ← MEM - 1
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
Clear the content of memory.
clear
M
Example: clear
Result: MEM ← 0
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
MEM ;
©Copyright 2020, PADAUK Technology Co. Ltd
Page 78 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
7.3. Shift Operation Instructions
sr
a
Shift right of ACC, shift 0 to bit 7.
Example: sr a ;
Result: a (0,b7,b6,b5,b4,b3,b2,b1) ← a (b7,b6,b5,b4,b3,b2,b1,b0), C ← a(b0)
Affected flags: 『N』Z 『Y』C 『N』AC 『N』OV
Shift right of ACC with carry bit 7 to flag.
Example: src a ;
src
sr
a
Result:
a (c,b7,b6,b5,b4,b3,b2,b1) ← a (b7,b6,b5,b4,b3,b2,b1,b0), C ← a(b0)
Affected flags: 『N』Z 『Y』C 『N』AC 『N』OV
Shift right the content of memory, shift 0 to bit 7.
Example: sr MEM ;
M
Result:
MEM(0,b7,b6,b5,b4,b3,b2,b1) ← MEM(b7,b6,b5,b4,b3,b2,b1,b0), C ← MEM(b0)
Affected flags: 『N』Z 『Y』C 『N』AC 『N』OV
Shift right of memory with carry bit 7 to flag.
Example: src MEM ;
src
sl
M
Result:
MEM(c,b7,b6,b5,b4,b3,b2,b1) ← MEM (b7,b6,b5,b4,b3,b2,b1,b0), C ← MEM(b0)
Affected flags: 『N』Z 『Y』C 『N』AC 『N』OV
Shift left of ACC shift 0 to bit 0.
a
Example: sl a ;
Result:
a (b6,b5,b4,b3,b2,b1,b0,0) ← a (b7,b6,b5,b4,b3,b2,b1,b0), C ← a (b7)
Affected flags: 『N』Z 『Y』C 『N』AC 『N』OV
Shift left of ACC with carry bit 0 to flag.
slc
sl
a
Example: slc a ;
Result: a (b6,b5,b4,b3,b2,b1,b0,c) ← a (b7,b6,b5,b4,b3,b2,b1,b0), C ← a(b7)
Affected flags: 『N』Z 『Y』C 『N』AC 『N』OV
Shift left of memory, shift 0 to bit 0.
M
Example: sl MEM ;
Result:
MEM (b6,b5,b4,b3,b2,b1,b0,0) ← MEM (b7,b6,b5,b4,b3,b2,b1,b0), C ← MEM(b7)
Affected flags: 『N』Z 『Y』C 『N』AC 『N』OV
Shift left of memory with carry bit 0 to flag.
Example: slc MEM ;
slc
M
Result:
MEM (b6,b5,b4,b3,b2,b1,b0,C) ← MEM (b7,b6,b5,b4,b3,b2,b1,b0), C ← MEM (b7)
Affected flags: 『N』Z 『Y』C 『N』AC 『N』OV
swap
a
Swap the high nibble and low nibble of ACC.
Example: swap
Result: a (b3,b2,b1,b0,b7,b6,b5,b4) ← a (b7,b6,b5,b4,b3,b2,b1,b0)
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
a ;
©Copyright 2020, PADAUK Technology Co. Ltd
Page 79 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
7.4. Logic Operation Instructions
and
and
and
or
a, I
a, M
M, a
a, I
Perform logic AND on ACC and immediate data, then put result into ACC.
Example: and a, 0x0f ;
Result: a ← a & 0fh
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
Perform logic AND on ACC and memory, then put result into ACC.
Example: and
a, RAM10 ;
Result: a ← a & RAM10
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
Perform logic AND on ACC and memory, then put result into memory.
Example: and
MEM, a ;
Result: MEM ← a & MEM
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
Perform logic OR on ACC and immediate data, then put result into ACC.
Example: or
a, 0x0f ;
Result: a ← a | 0fh
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
or
a, M
Perform logic OR on ACC and memory, then put result into ACC.
Example: or
a, MEM ;
Result: a ← a | MEM
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
or
M, a
a, I
Perform logic OR on ACC and memory, then put result into memory.
Example: or
MEM, a ;
Result: MEM ← a | MEM
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
xor
xor
Perform logic XOR on ACC and immediate data, then put result into ACC.
Example: xor
a, 0x0f ;
Result: a ← a ^ 0fh
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
IO, a
Perform logic XOR on ACC and IO register, then put result into IO register.
Example: xor
pa, a ;
Result: pa ← a ^ pa ; // pa is the data register of port A
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
xor
xor
a, M
M, a
Perform logic XOR on ACC and memory, then put result into ACC.
Example: xor
a, MEM ;
Result: a ← a ^ RAM10
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
Perform logic XOR on ACC and memory, then put result into memory.
Example:
xor
MEM, a ;
Result:
MEM ← a ^ MEM
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
©Copyright 2020, PADAUK Technology Co. Ltd
Page 80 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
not
a
Perform 1’s complement (logical complement) of ACC.
Example: not a ;
Result: a ← 〜a
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
Application Example:
------------------------------------------------------------------------------------------------------------------------
mov
not
a, 0x38 ;
a ;
// ACC=0X38
// ACC=0XC7
------------------------------------------------------------------------------------------------------------------------
Perform 1’s complement (logical complement) of memory.
not
M
Example: not
MEM ;
Result: MEM ← 〜MEM
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
Application Example:
------------------------------------------------------------------------------------------------------------------------
mov
mov
not
a, 0x38 ;
mem, a ;
mem ;
// mem = 0x38
// mem = 0xC7
------------------------------------------------------------------------------------------------------------------------
Perform 2’s complement of ACC.
neg
a
Example: neg
a;
Result: a ← 〒a
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
Application Example:
------------------------------------------------------------------------------------------------------------------------
mov
neg
a, 0x38 ;
a ;
// ACC=0X38
// ACC=0XC8
------------------------------------------------------------------------------------------------------------------------
Perform 2’s complement of memory.
neg
M
Example: neg
MEM;
Result: MEM ← 〒MEM
Affected flags: 『Y』Z 『N』C 『N』AC 『N』OV
Application Example:
------------------------------------------------------------------------------------------------------------------------
mov
mov
not
a, 0x38 ;
mem, a ;
mem ;
// mem = 0x38
// mem = 0xC8
------------------------------------------------------------------------------------------------------------------------
©Copyright 2020, PADAUK Technology Co. Ltd
Page 81 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
7.5. Bit Operation Instructions
set0 IO.n
set1 IO.n
swapc IO.n
Set bit n of IO port to low.
Example: set0 pa.5 ;
Result: set bit 5 of port A to low
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Set bit n of IO port to high.
Example: set1 pb.5 ;
Result: set bit 5 of port B to high
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Swap the nth bit of IO port with carry bit.
Example: swapc
IO.0;
Result: C ← IO.0 , IO.0 ← C
When IO.0 is a port to output pin, carry C will be sent to IO.0;
When IO.0 is a port from input pin, IO.0 will be sent to carry C;
Affected flags: 『N』Z 『Y』C 『N』AC 『N』OV
Application Example1 (serial output) :
------------------------------------------------------------------------------------------------------------------------
...
set1
...
pac.0 ;
// set PA.0 as output
set0
swapc
set1
swapc
...
flag.1 ;
pa.0 ;
flag.1 ;
pa.0 ;
// C=0
// move C to PA.0 (bit operation), PA.0=0
// C=1
// move C to PA.0 (bit operation), PA.0=1
------------------------------------------------------------------------------------------------------------------------
Application Example2 (serial input) :
------------------------------------------------------------------------------------------------------------------------
...
set0
...
pac.0 ;
// set PA.0 as input
swapc
src
pa.0 ;
a ;
// read PA.0 to C (bit operation)
// shift C to bit 7 of ACC
swapc
src
pa.0 ;
a ;
// read PA.0 to C (bit operation)
// shift new C to bit 7, old C
...
------------------------------------------------------------------------------------------------------------------------
set0 M.n
set1 M.n
Set bit n of memory to low.
Example: set0 MEM.5 ;
Result:
set bit 5 of MEM to low
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Set bit n of memory to high.
Example: set1 MEM.5 ;
Result:
set bit 5 of MEM to high
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
©Copyright 2020, PADAUK Technology Co. Ltd
Page 82 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
7.6. Conditional Operation Instructions
ceqsn a, I
Compare ACC with immediate data and skip next instruction if both are equal.
Flag will be changed like as (a ← a – I)
Example: ceqsn
a, 0x55 ;
MEM ;
inc
goto
error ;
Result:
If a=0x55, then “goto error”; otherwise, “inc MEM”.
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
Compare ACC with memory and skip next instruction if both are equal.
Flag will be changed like as (a ← a - M)
ceqsn a, M
cneqsn a, M
Example: ceqsn
a, MEM;
Result: If a=MEM, skip next instruction
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
Compare ACC with memory and skip next instruction if both are not equal.
Flag will be changed like as (a ← a - M)
Example: cneqsn
a, MEM;
Result: If a≠MEM, skip next instruction
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
Compare ACC with immediate data and skip next instruction if both are no equal.
Flag will be changed like as (a ← a - I)
cneqsn a, I
Example: cneqsn
a,0x55 ;
MEM ;
error ;
inc
goto
Result:
If a≠0x55, then “goto error”; Otherwise, “inc MEM”.
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
t0sn IO.n
t1sn IO.n
t0sn M.n
t1sn M.n
Check IO bit and skip next instruction if it’s low.
Example: t0sn
pa.5;
Result: If bit 5 of port A is low, skip next instruction
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Check IO bit and skip next instruction if it’s high.
Example: t1sn
pa.5 ;
Result: If bit 5 of port A is high, skip next instruction
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Check memory bit and skip next instruction if it’s low .
Example: t0sn MEM.5 ;
Result:
If bit 5 of MEM is low, then skip next instruction
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Check memory bit and skip next instruction if it’s high.
Example: t1sn MEM.5 ;
Result:
If bit 5 of MEM is high, then skip next instruction
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
izsn
a
Increment ACC and skip next instruction if ACC is zero.
Example: izsn
Result:
a;
a
←
a + 1,skip next instruction if a = 0
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
©Copyright 2020, PADAUK Technology Co. Ltd
Page 83 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
dzsn
izsn
a
Decrement ACC and skip next instruction if ACC is zero.
Example: dzsn a;
Result: A - 1,skip next instruction if a = 0
A
←
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
M
Increment memory and skip next instruction if memory is zero.
Example: izsn
Result: MEM
MEM;
MEM + 1, skip next instruction if MEM= 0
←
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
dzsn
M
Decrement memory and skip next instruction if memory is zero.
Example: dzsn
Result: MEM
Affected flags: 『Y』Z 『Y』C 『Y』AC 『Y』OV
MEM;
←
MEM - 1, skip next instruction if MEM = 0
7.7. System control Instructions
call
label
Function call, address can be full range address space.
Example: call
Result: [sp]
function1;
pc + 1
←
pc
sp
←
function1
sp + 2
←
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
goto label
Go to specific address which can be full range address space.
Example: goto
error;
Result: Go to error and execute program.
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Place immediate data to ACC, then return.
Example: ret 0x55;
ret
ret
I
Result:
A ← 55h
ret ;
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Return to program which had function call.
Example: ret;
Result:
sp ← sp - 2
pc ← [sp]
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
reti
Return to program that is interrupt service routine. After this command is executed, global
interrupt is enabled automatically.
Example: reti;
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
No operation.
nop
Example: nop;
Result:
nothing changed
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
©Copyright 2020, PADAUK Technology Co. Ltd
Page 84 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
pcadd
a
Next program counter is current program counter plus ACC.
Example: pcadd a;
Result: pc ← pc + a
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
------------------------------------------------------------------------------------------------------------------------
Application Example:
------------------------------------------------------------------------------------------------------------------------
…
mov
pcadd
goto
goto
goto
goto
…
a, 0x02 ;
a ;
err1 ;
correct ;
err2 ;
err3 ;
// PC <- PC+2
// jump here
correct:
// jump here
…
------------------------------------------------------------------------------------------------------------------------
engint
Enable global interrupt enable.
Example: engint;
Result:
Interrupt request can be sent to CPU
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Disable global interrupt enable.
disgint
stopsys
stopexe
Example: disgint ;
Result:
Interrupt request is blocked from CPU
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
System halt.
Example: stopsys;
Result:
Stop the system clocks and halt the system
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
CPU halt. The oscillator module is still active to output clock, however, system clock is disabled
to save power.
Example: stopexe;
Result:
Stop the system clocks and keep oscillator modules active.
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Reset the whole chip, its operation will be same as hardware reset.
Example: reset;
reset
Result:
Reset the whole chip.
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
Reset Watchdog timer.
wdreset
Example: wdreset ;
Result:
Reset Watchdog timer.
Affected flags: 『N』Z 『N』C 『N』AC 『N』OV
©Copyright 2020, PADAUK Technology Co. Ltd
Page 85 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
7.8. Summary of Instructions Execution Cycle
goto, call, pcadd, ret, reti , idxm
2T
2T
1T
1T
Condition is fulfilled.
ceqsn, cneqsn, t0sn, t1sn, dzsn, izsn
Condition is not fulfilled.
Others
7.9. Summary of affected flags by Instructions
Instruction
mov a, I
Z
-
C
-
AC OV Instruction
Z
-
C
-
AC OV Instruction
Z
Y
-
C
-
AC OV
-
-
-
-
mov M, a
mov IO, a
idxm a, index
pushaf
-
-
-
-
mov a, M
ldt16 word
idxm index, a
popaf
-
-
-
-
mov a, IO
stt16 word
Y
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
xch
M
-
-
-
-
-
-
-
-
Y
Y
Y
Y
Y
Y
-
Y
Y
Y
Y
Y
Y
Y
Y
Y
-
Y
Y
Y
Y
Y
Y
-
Y
Y
Y
Y
Y
Y
-
add a, I
Y
Y
Y
Y
Y
Y
-
Y
Y
Y
Y
Y
Y
Y
Y
Y
-
Y
Y
Y
Y
Y
Y
-
Y
Y
Y
Y
Y
Y
-
add a, M
addc M, a
sub a, I
Y
Y
Y
Y
Y
-
Y
Y
Y
Y
Y
-
Y
Y
Y
Y
Y
-
Y
Y
Y
Y
Y
-
add M, a
addc a, M
addc
a
addc
M
sub a, M
sub M, a
subc a, M
subc M, a
subc
dec
src
a
subc
clear
M
M
inc
sr a
src
sl
M
M
M
a
sr
M
-
Y
Y
-
-
-
-
-
-
sl
a
-
-
-
slc
a
-
-
-
M
-
-
-
slc
and
M
-
-
-
swap
and
a
-
-
-
and
a, I
Y
Y
Y
Y
Y
-
-
-
a, M
Y
Y
-
-
-
M, a
Y
Y
Y
Y
-
-
-
-
or a, I
-
-
-
or a, M
-
-
-
or M, a
-
-
-
xor
xor
neg
a, I
-
-
-
xor
not
neg
IO, a
-
-
-
xor
not
a, M
-
-
-
M, a
a
-
-
-
a
Y
Y
-
-
-
-
M
-
-
-
-
-
-
M
-
-
-
set0 IO.n
set1 M.n
t0sn IO.n
t1sn M.n
-
-
-
set1 IO.n
ceqsn a, I
t1sn IO.n
-
-
-
set0 M.n
ceqsn a, M
t0sn M.n
-
-
-
-
-
-
-
Y
-
Y
-
Y
-
Y
-
Y
-
Y
-
Y
-
Y
-
-
-
-
-
-
-
-
-
izsn
dzsn
ret
a
Y
Y
-
Y
Y
-
Y
Y
-
Y
Y
-
dzsn
call
a
Y
-
Y
-
Y
-
Y
-
izsn
M
Y
-
Y
-
Y
-
Y
-
M
label
goto label
reti
I
ret
-
-
-
-
-
-
-
-
nop
-
-
-
-
pcadd
a
-
-
-
-
engint
-
-
-
-
disgint
reset
-
-
-
-
stopsys
-
-
-
-
stopexe
swapc IO.n
-
-
-
-
-
-
-
-
wdreset
-
-
-
-
-
Y
-
-
ceqsn a, I
Y
Y
Y
Y
cneqsn a, M
Y
Y
Y
Y
7.10.BIT definition
Bit access of RAM is only available for address from 0x00 to 0x3F.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 86 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
8. Code Options
Option
Selection
Description
Enable
Disable
Normal
Strong
4.0V
OTP content is protected and program cannot be read back
OTP content is not protected so program can be read back
PB4 & PB5 Drive/ Sink Current= 5mA/ 10mA
PB4 & PB5 Drive/ Sink Current=20mA/ 40mA
LVR typical range 4.0V
Security
PB4_PB5_Drive
3.5V
LVR typical range 3.5V
3.0V
LVR typical range 3.0V
2.7V
LVR typical range 2.7V
LVR
2.5V
LVR typical range 2.5V
2.2V
2.0V
1.8V
Slow
Fast
LVR typical range 2.2V
LVR typical range 2.0V
LVR typical range 1.8V
About 3000 ILRC clock cycles
About 45 ILRC clock cycles
INTEN/ INTRQ.Bit0 is for PA.0
INTEN/ INTRQ.Bit0 is for PB.5
INTEN/ INTRQ.Bit1 is for PB.0
INTEN/ INTRQ.Bit1 is for PA.4
GPC INT both Rising & Falling edge trigger
Boot-up_Time
Interrupt Src0
Interrupt Src1
PA.0
PB.5
PB.0
PA.4
All Edge
Rising Edge GPC INT at Rising edge trigger
Falling Edge GPC INT at Falling edge trigger
Comparator Edge
GPC_PWM
Disable
Enable
GPC/ PWM are independent
GPC output control PWM output (ICE does NOT Support.)
When tm2c[7:4]= 0010, TM2 clock source = IHRC = 16MHZ
When tm3c[7:4]= 0010, TM3 clock source = IHRC = 16MHZ
When tm2c[7:4]= 0010, TM2 clock source = IHRC*2 = 32MHZ
When tm3c[7:4]= 0010, TM3 clock source = IHRC*2 = 32MHZ
(ICE does NOT Support.)
16MHZ
32MHZ
6 Bit
TMX Source
When tm2s.7=1, TM2 PWM resolution is 6 Bit
When tm3s.7=1, TM3 PWM resolution is 6 Bit
When tm2s.7=1, TM2 PWM resolution is 7 Bit
When tm3s.7=1, TM3 PWM resolution is 7 Bit
(ICE does NOT Support.)
TMX Bit
7 Bit
PB0
PB2
tm2c[3:2]=1 for PB0 as TM2 Output (ICE does NOT Support.)
tm2c[3:2]=1 for PB2 as TM2 Output
TM2 Out1
©Copyright 2020, PADAUK Technology Co. Ltd
Page 87 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
9. Special Notes
This chapter is to remind user who use PMS171B series IC in order to avoid frequent errors upon operation.
9.1. Warning
User must read all application notes of the IC by detail before using it. Please download the related application
notes from the following link:
http://www.padauk.com.tw/tw/technical/index.aspx
9.2. Using IC
9.2.1. IO pin usage and setting
(1) IO pin as digital input
When IO is set as digital input, the level of Vih and Vil would changes with the voltage and temperature.
Please follow the minimum value of Vih and the maximum value of Vil.
The value of internal pull high resistor would also changes with the voltage, temperature and pin voltage.
It is not the fixed value.
(2) IO pin as digital input and enable wakeup function
Configure IO pin as input
Set PADIER and PBDIER registers to set the corresponding bit to 1.
(3) PA5 is set to be output pin
PA5 can be set to be Open-Drain output pin only, output high requires adding pull-high resistor
externally.
(4) PA5 is set to be PRSTB input pin
Configure PA5 as input
Set CLKMD.0=1 to enable PA5 as PRSTB input pin
(5) PA5 is set to be input pin and to connect with a push button or a switch by a long wire
Needs to put a >33Ω resistor in between PA5 and the long wire
Avoid using PA5 as input in such application.
(6) PA7 and PA6 as external crystal oscillator
Configure PA7 and PA6 as input
Disable PA7 and PA6 internal pull-high resistor
Configure PADIER register to set PA6 and PA7 as analog input
EOSCR register bit [6:5] selects corresponding crystal oscillator frequency :
01 : for lower frequency, ex : 32KHz
10 : for middle frequency, ex : 455KHz,1MHz
11 : for higher frequency, ex : 4MHz
Program EOSCR.7 =1 to enable crystal oscillator
Ensure EOSC working well before switching from IHRC or ILRC to EOSC
©Copyright 2020, PADAUK Technology Co. Ltd
Page 88 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
Note: Please read the PMC-APN013 carefully. According to PMC-APN013, the crystal oscillator should be
used reasonably. If the following situations happen to cause IC start-up slowly or non-startup, PADAUK
Technology is not responsible for this: the quality of the user's crystal oscillator is not good, the usage
conditions are unreasonable, the PCB cleaner leakage current, or the PCB layouts are unreasonable.
9.2.2. Interrupt
(1) When using the interrupt function, the procedure should be:
Step1: Set INTEN register, enable the interrupt control bit
Step2: Clear INTRQ register
Step3: In the main program, using ENGINT to enable CPU interrupt function
Step4: Wait for interrupt. When interrupt occurs, enter to Interrupt Service Routine
Step5: After the Interrupt Service Routine being executed, return to the main program
*Use DISGINT in the main program to disable all interrupts
*When interrupt service routine starts, use PUSHAF instruction to save ALU and FLAG register.
POPAF instruction is to restore ALU and FLAG register before RETI as below:
void Interrupt (void)
// Once the interrupt occurs, jump to interrupt service routine
{
// enter DISGINT status automatically, no more interrupt is accepted
PUSHAF;
…
POPAF;
}
// RETI will be added automatically. After RETI being executed, ENGINT
status will be restored
(2) INTEN and INTRQ have no initial values. Please set required value before enabling interrupt function
(3) There are two sets of external IO pin interrupt source. Every set is decided by code option Interrupt Src0
and Interrupt Src1 corresponding to the unique interrupt pin. Please comply with the inten / intrq / integs
register when selecting IO pin.
9.2.3. System clock switching
(1) System clock can be switched by CLKMD register. Please notice that, NEVER switch the system clock and
turn off the original clock source at the same time. For example: When switching from clock A to clock B,
please switch to clock B first; and after that turn off the clock A oscillator through CLKMD.
Example : Switch system clock from ILRC to IHRC/2
CLKMD
=
0x36;
0;
// switch to IHRC, ILRC cannot be disabled here
CLKMD.2 =
// ILRC can be disabled at this time
ERROR: Switch ILRC to IHRC and turn off ILRC simultaneously
CLKMD 0x50; // MCU will hang
=
(2) Please ensure the EOSC oscillation has established before switching from ILRC or IHRC to EOSC. MCU
will not check its status. Please wait for a while after enabling EOSC. System clock can be switched to
©Copyright 2020, PADAUK Technology Co. Ltd
Page 89 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
EOSC afterwards. Otherwise, MCU will hang. The example for switching system clock from ILRC to 4MHz
EOSC after boot up as below:
.ADJUST_IC
DISABLE
CLKMD.1 = 0;
// turn off WDT for executing delay instruction
// 4MHz EOSC start to oscillate
$
EOSCR
Enable, 4MHz;
// Delay for EOSC establishment
$ T16M EOSC, /1, BIT10
Word Count = 0;
Stt16 Count;
Intrq.T16 = 0;
while(!Intrq.T16) NULL;
CLKMD = 0xA4;
CLKMD.2 = 0;
// ILRC -> EOSC;
// turn off ILRC only if necessary
The delay duration should be adjusted in accordance with the characteristic of the crystal and PCB. To
measure the oscillator signal by the oscilloscope, please select (x10) on the probe and measure through
PA6(X2) pin to avoid the interference on the oscillator.
9.2.4. Watchdog
Watchdog will be inactive once ILRC is disabled.
9.2.5. TIMER time out
When select $ INTEGS BIT_R (default value) and T16M counter BIT8 to generate interrupt, if T16M counts
from 0, the first interrupt will occur when the counter reaches to 0x100 (BIT8 from 0 to 1) and the second
interrupt will occur when the counter reaches 0x300 (BIT8 from 0 to 1). Therefore, selecting BIT8 as 1 to
generate interrupt means that the interrupt occurs every 512 counts. Please notice that if T16M counter is
restarted, the next interrupt will occur once Bit8 turns from 0 to 1.
If select $ INTEGS BIT_F(BIT triggers from 1 to 0) and T16M counter BIT8 to generate interrupt, the T16M
counter changes to an interrupt every 0x200/0x400/0x600/. Please pay attention to two differences with
setting INTEGS methods.
9.2.6. IHRC
(1)
The IHRC frequency calibration is performed when IC is programmed by the writer.
Because the characteristic of the Epoxy Molding Compound (EMC) would some degrees affects the
IHRC frequency (either for package or COB), if the calibration is done before molding process, the
actual IHRC frequency after molding may be deviated or becomes out of spec. Normally, the frequency
is getting slower a bit.
(2)
(3)
(4)
It usually happens in COB package or Quick Turnover Programming (QTP). And PADAUK would not
take any responsibility for this situation.
Users can make some compensatory adjustments according to their own experiences. For example,
users can set IHRC frequency to be 0.5% ~ 1% higher and aim to get better re-targeting after molding.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 90 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
9.2.7. LVR
LVR level selection is done at compile time. User must select LVR based on the system working frequency
and power supply voltage to make the MCU work stably.
The following are Suggestions for setting operating frequency, power supply voltage and LVR level:
SYSCLK
8MHz
VDD
LVR
≧ 3.0V
≧ 2.2V
≧ 1.8V
≧ 3.0V
≧ 2.2V
≧ 1.8V
4MHz
2MHz
Table 8: LVR setting for reference
(1) The setting of LVR (1.8V ~ 4.0V) will be valid just after successful power-on process.
(2) User can set MISC.2 as “1” to disable LVR. However, VDD must be kept as exceeding the lowest working
voltage of chip; Otherwise IC may work abnormally.
(3) The LVR function will be invalid when IC in stopexe or stopsys mode.
9.2.8. Programming Writing
There are 6 signals for programming PMS171B: PA3, PA4, PA5, PA6, VDD, and GND.
If using PDK3S-P-002 to program PMS171B, please put the jumper over CN39. For 16pin package, please
put the IC at the very top of the Textool. For 14pin package, please put the IC downwards by one space from
the top of the Textool. For 10pin package (such as MSOP10), please put the IC downwards by three spaces.
For 8pin package, please put the IC downwards by four spaces from the top of the Textool. Other packages
could be programmed by appropriate connection by the users. All the signals on the left side pins of the
jumper are identical and same as the labeled on CN42 at left bottom corner: they are VDD, PA0 (not required),
PA3, PA4, PA5, PA6, PA7 (not required), and GND.
©Copyright 2020, PADAUK Technology Co. Ltd
Page 91 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
PMS171B
8bit OTP MCU with 8-bit ADC
If user use PDK5S-P-003 or above to program, please follow the instruction displayed at the software to
connect the jumper.
Special notes about voltage and current while Multi-Chip-Package(MCP) or On-Board Programming
(1) PA5 (VPP) may be higher than 11V.
(2)
VDD may be higher than 7.8V, and its maximum current may reach about 20mA.
(3) All other signal pins level (except GND) are the same as VDD.
User should confirm when using this product in MCP or On-Board Programming, the peripheral circuit or
components will not be destroyed or limit the above voltages.
9.3 Using ICE
(1) PDK5S-I-S01/2(B) supports PMS171B MCU emulation work, the following items should be noted when
using PDK5S-I-S01/2(B) to emulate PMS171B:
PDK5S-I-S01/2(B) doesn’t support SYSCLK=ILRC/16 of PMS171B.
PDK5S-I-S01/2(B) doesn’t support the function TM2C.PB0 of PMS171B.
PDK5S-I-S01/2(B) doesn’t support the code options: GPC_PWM, TMx_source, TMx_bit, TM2_Out1.
PDK5S-I-S01/2(B) doesn’t support the function PBPL (PB pull low)
If the comparator doesn’t need to wake up “stopexe”, please set GPCC.7 = 0, GPCS.6 = 0
When using PB1 in ADCRGC, PA1 must float.
When using GPCC output, PA3 will be influenced.
When simulating PWM waveform, please check the waveform during program running. When the ICE is
suspended or single-step running, its waveform may be inconsistent with the reality.
The ILRC frequency of the PDK5S-I-S01/2(B) simulator is different from the actual IC and is
uncalibrated, with a frequency range of about 34K~38KHz.
Fast Wakeup time is different from ICE: 128 SysClk, PMS171B: 45 ILRC
Watch dog time out period is different from ICE:
WDT period
misc[1:0]=00
misc[1:0]=01
misc[1:0]=10
misc[1:0]=11
PDK5S-I-S01/2(B)
2048 * TILRC
PMS171B
8192 * TILRC
16384 * TILRC
65536 * TILRC
262144 * TILRC
4096 * TILRC
16384 * TILRC
256 * TILRC
©Copyright 2020, PADAUK Technology Co. Ltd
Page 92 of 92
PDK-DS-PMS171B-EN_V103 – Sep. 2, 2020
相关型号:
©2020 ICPDF网 联系我们和版权申明