NCP663SQ25T1 [ONSEMI]
100 mA CMOS Low Iq Low-Dropout Voltage Regulator; 百毫安CMOS低Iq低压差稳压器型号: | NCP663SQ25T1 |
厂家: | ONSEMI |
描述: | 100 mA CMOS Low Iq Low-Dropout Voltage Regulator |
文件: | 总10页 (文件大小:70K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NCP662, NCV662, NCP663,
NCV663
100 mA CMOS Low Iq
Low−Dropout Voltage
Regulator
This series of fixed output low−dropout linear regulators are
designed for handheld communication equipment and portable battery
powered applications which require low quiescent current. This series
http://onsemi.com
4
features an ultra−low quiescent current of 2.5
Am. Each device
contains a voltage reference unit, an error amplifier, a PMOS power
transistor, resistors for setting output voltage, current limit, and
temperature limit protection circuits. The NCP662/NCV662 series
provides an enable pin for ON/OFF control.
This series has been designed to be used with low cost ceramic
capacitors and requires a minimum output capacitor of 0.1 m F. The
device is housed in the micro−miniature SC82−AB surface mount
package. Standard voltage versions are 1.5, 1.8, 2.5, 2.7, 2.8, 3.0, 3.3,
and 5.0 V.
1
SC82−AB (SC70−4)
SQ SUFFIX
CASE 419C
PIN CONNECTIONS &
MARKING DIAGRAMS
Features
• Low Quiescent Current of 2.5 m A Typical
• Low Output Voltage Option
• Output Voltage Accuracy of 2.0%
• Temperature Range for NCV662/NCV663 −40°C to 125°C
Temperature Range for NCP662/NCP663 −40°C to 85°C
• NCP662/NCV662 Provides as Enable Pin
GND
Enable
1
2
4
3
V
in
V
out
(NCP662/NCV662 Top View)
• NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
GND
N/C
1
2
4
3
• Pb−Free Packages are Available
Typical Applications
V
in
V
out
• Battery Powered Instruments
• Hand−Held Instruments
• Camcorders and Cameras
• Automotive Infotainment
(NCP663/NCV663 Top View)
xxx = Device Code
M
= Date Code
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 8 of this data sheet.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
Semiconductor Components Industries, LLC, 2005
1
Publication Order Number:
March, 2005 − Rev. 1
NCP662/D
NCP662, NCV662, NCP663, NCV663
ON
GND Enable
GND
N/C
OFF
Input
Output
Input
Output
V
in
V
out
V
in
V
out
+
+
+
+
C1
C2
C1
C2
This device contains 28 active transistors
This device contains 28 active transistors
Figure 1. NCP662/NCV662 Typical Application
Diagram
Figure 2. NCP663/NCV663 Typical Application
Diagram
PIN FUNCTION DESCRIPTION
NCP662/
NCV662
NCP663/
NCV663
Pin Name
GND
Description
1
2
3
4
1
2
3
−
Power supply ground.
Vin
Positive power supply input voltage.
Regulated output voltage.
Vout
Enable
This input is used to place the device into low−power standby. When this input is pulled low, the
device is disabled. If this function is not used, Enable should be connected to Vin.
−
4
N/C
No internal connection.
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
V
Input Voltage
V
in
6.0
Enable Voltage (NCP662/NCV662 ONLY)
Output Voltage
Enable
−0.3 to V +0.3
V
in
V
out
−0.3 to V +0.3
V
in
Power Dissipation and Thermal Characteristics
Power Dissipation
Thermal Resistance, Junction to Ambient
P
Internally Limited
330
W
°C/W
D
R
q
JA
Operating Junction Temperature
T
+150
°C
°C
J
Operating Ambient Temperature
NCP662/NCP663
NCV662/NCV663
T
A
−40 to +85
−40 to +125
Storage Temperature
T
stg
−55 to +150
°C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL−STD−883, Method 3015
Machine Model Method 200 V
2. Latch up capability (85°C) "100 mA DC with trigger voltage.
http://onsemi.com
2
NCP662, NCV662, NCP663, NCV663
ELECTRICAL CHARACTERISTICS
(V = V
+ 1.0 V, V = V , C = 1.0 m F, C = 1.0 m F, T = 25°C, unless otherwise noted.)
enable in in out J
in
out(nom.)
Characteristic
Symbol
Min
Typ
Max
Unit
Output Voltage (I = 1.0 mA)
V
out
V
out
NCP662/NCP663: TA = −40°C to 85°C
NCV662/NCV663: TA = −40°C to 125°C
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.3 V
5.0 V
1.463
1.755
2.438
2.646
2.744
2.940
3.234
4.9
1.5
1.8
2.5
2.7
2.8
3.0
3.3
5.0
1.538
1.845
2.563
2.754
2.856
3.060
3.366
5.1
Output Voltage (TA = −40°C to 85°C, I = 100 mA)
V
out
V
out
1.5 V
1.8 V
2.5 V
2.7 V
2.8 V
3.0 V
3.3 V
5.0 V
1.433
1.719
2.388
2.592
2.688
2.880
3.168
4.8
1.5
1.8
2.5
2.7
2.8
3.0
3.3
5.0
1.568
1.881
2.613
2.808
2.912
3.120
3.432
5.2
Line Regulation
Reg
mV
line
1.5 V−4.4 V (V = V
+ 1.0 V to 6.0 V
−
−
10
10
20
20
in
o(nom.)
4.5 V−5.0 V (V = 5.5 V to 6.0 V)
in
Load Regulation (I = 10 mA to 100 mA)
Reg
−
20
40
mV
mA
out
load
Output Current (V = (V at I = 100 mA) −3.0%)
I
o(nom.)
out
out
out
1.5 V to 3.9 V (V = V
+ 2.0 V)
100
100
280
280
−
−
in
out(nom.)
4.0 V−5.0 V (V = 6.0 V)
in
Dropout Voltage (I = 100 mA, Measured at V −3.0%)
V −V
in out
mV
out
out
NCP662/NCP663: TA = −40°C to 85°C
NCV662/NCV663: TA = −40°C to 125°C
1.5 V−1.7 V
1.8 V−2.4 V
2.5 V−2.6 V
2.7 V−2.9 V
3.0 V−3.2 V
3.3 V−4.9 V
5.0 V
−
−
−
−
−
−
−
680
500
300
280
250
230
170
950
700
500
500
420
420
300
Quiescent Current
(Enable Input = 0 V)
I
Q
m
A
−
−
0.1
2.5
1.0
6.0
(Enable Input = V , I = 1.0 mA to I
)
in out
o(nom.)
Output Short Circuit Current
I
mA
out(max)
1.5 V to 3.9 V (V = V
+ 2.0 V)
150
150
300
300
600
600
in
nom
4.0 V−5.0 V (V = 6.0 V)
in
Output Voltage Noise (f = 100 Hz to 100 kHz, V = 3.0 V)
V
n
−
100
−
m
V
r
m
s
out
Enable Input Threshold Voltage (NCP662/NCV662 ONLY)
(Voltage Increasing, Output Turns On, Logic High)
(Voltage Decreasing, Output Turns Off, Logic Low)
V
th(en)
V
1.3
−
−
−
−
0.5
Output Voltage Temperature Coefficient
T
C
−
"100
−
ppm/°C
3. Maximum package power dissipation limits must be observed.
T
*T
A
qJA
J(max)
PD +
R
4. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
http://onsemi.com
3
NCP662, NCV662, NCP663, NCV663
3
2.9
2.7
2.5
2.3
V
V
= 4.0 V
= 3.0 V
= 0 mA
IN
OUT
2.5
2
V
OUT
= 3.0 V
I
OUT
1.5
1
2.1
0.5
0
1.9
1.7
−60 −40
−20
0
20
40
60
80
100
0
1
2
3
4
5
6
T, TEMPERATURE (°C)
V
IN
, INPUT VOLTAGE (V)
Figure 3. Quiescent Current versus Temperature
Figure 4. Quiescent Current versus Input
Voltage
3.020
3.5
3
3.015
3.010
3.005
3.000
I
= 30 mA
OUT
V
= 6.0 V
IN
2.5
2
1.5
1
V
= 4.0 V
80
IN
V
= 3.0 V
= 10 mA
OUT(nom)
2.995
2.990
0.5
0
I
OUT
−60 −40 −20
0
20
40
60
100
0
1
2
3
4
5
6
T, TEMPERATURE (°C)
V
IN
, INPUT VOLTAGE (V)
Figure 5. Output Voltage versus Temperature
Figure 6. Output Voltage versus Input Voltage
4
2
0
3
2
300
250
200
150
100
V
= 3.0 V
OUT(nom)
V
C
= 4.0 V
= 1.0 m F
IN
80 mA LOAD
IN
C
= 0.1 m F
= 10 mA
OUT
40 mA LOAD
10 mA LOAD
I
OUT
50
0
1
0
−50 −25
0
25
50
75
100
125
0
50
100
150
200
250
300
350 400
T, TEMPERATURE (°C)
t, TIME (m s)
Figure 7. Dropout Voltage versus Temperature
Figure 8. Turn−On Response
(NCP662/NCV662 ONLY)
http://onsemi.com
4
NCP662, NCV662, NCP663, NCV663
6
60
I
= 1.0 mA to
30 mA
OUT
5
4
30
0
V
IN
= 4.0 V
3
1
−30
1
V
C
= 3.0 V
= 0.1 m F
OUT
0.5
0
0.5
0
OUT
V
OUT
= 3.0 V
C
= 0.1 m F
= 10 mA
−0.5
−1
−0.5
−1
OUT
I
OUT
0
50 100 150 200 250 300 350 400 450 500
0
50 100 150 200 250 300 350 400 450 500
t, TIME (m s)
t, TIME (m s)
Figure 9. Line Transient Response
Figure 10. Load Transient Response
60
3.5
3
I
V
= 1.0 mA to 30 mA
= 4.0 V
OUT
V
V
= 5.0 V
= 3.0 V
= 50 mA
30
0
IN
OUT
IN
I
OUT
2.5
2
C
= 0.1 m F
OUT
−30
400
1.5
1
200
0
C
V
= 1.0 m F
= 3.0 V
OUT
OUT
0.5
0
−200
−400
0
100 200 300 400 500 600 700 800 900 1000
0.01
0.1
1
10
100
1000
t, TIME (m s)
f, FREQUENCY (kHz)
Figure 11. Load Transient Response
Figure 12. Output Voltage Noise
http://onsemi.com
5
NCP662, NCV662, NCP663, NCV663
DEFINITIONS
Line Regulation
Load Regulation
The change in output voltage for a change in output
current at a constant temperature.
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse technique such that the average
chip temperature is not significantly affected.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 3.0% below
its nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Line Transient Response
Typical over and undershoot response when input voltage
is excited with a given slope.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 160°C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Maximum Power Dissipation
The maximum total dissipation for which the regulator
will operate within its specifications.
Quiescent Current
The quiescent current is the current which flows through
the ground when the LDO operates without a load on its
output: internal IC operation, bias, etc. When the LDO
becomes loaded, this term is called the Ground current. It is
actually the difference between the input current (measured
through the LDO input pin) and the output current.
Maximum Package Power Dissipation
The maximum power package dissipation is the power
dissipation level at which the junction temperature reaches
its maximum operating value, i.e. 125°C. Depending on the
ambient power dissipation and thus the maximum available
output current.
http://onsemi.com
6
NCP662, NCV662, NCP663, NCV663
APPLICATIONS INFORMATION
A typical application circuit for the NCP662/NCV662
and NCP663/NCV663 series are shown in Figure 1 and
Figure 2.
Place external components, especially the output
capacitor, as close as possible to the circuit, and make leads
as short as possible.
Input Decoupling (C1)
Thermal
A 1.0 m F capacitor, either ceramic or tantalum is
recommended and should be connected close to the device
package. Higher capacitance values and lower ESR will
improve the overall line transient response.
As power across the NCP662/NCV662 and
NCP663/NCV663 increases, it might become necessary to
provide some thermal relief. The maximum power
dissipation supported by the device is dependent upon board
design and layout. The mounting pad configuration on the
PCB, the board material, and the ambient temperature effect
the rate of temperature rise for the part. This is stating that
when the devices have good thermal conductivity through
the PCB, the junction temperature will be relatively low with
high power dissipation applications.
TDK capacitor: C2012X5R1C105K or C1608X5R1A105K
Output Decoupling (C2)
The NCP662/NCV662 and NCP663/NCV663 are very
stable regulators and do not require any specific Equivalent
Series Resistance (ESR) or a minimum output current.
Capacitors exhibiting ESRs ranging from a few mW up to
10 W can safely be used. The minimum decoupling value is
0.1 m F and can be augmented to fulfill stringent load
transient requirements. The regulator accepts ceramic chip
capacitors as well as tantalum devices. Larger values
improve noise rejection and load regulation transient
response.
The maximum dissipation the package can handle is
given by:
T
*T
A
qJA
J(max)
PD +
R
If junction temperature is not allowed above the
maximum 125°C, then the NCP662/NCV662 and
NCP663/NCV663 can dissipate up to 300 mW @ 25°C.
The power dissipated by the NCP662/NCV662 and
NCP663/NCV663 can be calculated from the following
equation:
TDK capacitor: C2012X5R1C105K, C1608X5R1A105K,
or C3216X7R1C105K
Enable Operation (NCP662/NCV662 ONLY)
The enable pin will turn on the regulator when pulled high
and turn off the regulator when pulled low. The threshold
limits are covered in the electrical specification section of
the data sheet. If the enable is not used, the pin should be
[
]
[
]
P
+ V * I
(I ) ) V * V
* I
tot
in gnd out
in
out out
or
)
*
I
P
+
V
tot
I
out out
) I
V
inMAX
connected to V .
in
gnd
out
If an 100 mA output current is needed then the ground
current from the data sheet is 2.5 m A. For the
NCP662/NCV662 or NCP663/NCV663 (3.0 V), the
maximum input voltage is 6.0 V.
Hints
Please be sure the Vin and GND lines are sufficiently
wide. When the impedance of these lines is high, there is a
chance to pick up noise or cause the regulator to
malfunction.
http://onsemi.com
7
NCP662, NCV662, NCP663, NCV663
ORDERING INFORMATION
Nominal
Output Voltage
Device
NCP662SQ15T1
Marking
LGY
LGY
LGZ
LGZ
LHA
LHA
LHB
LHB
LHC
LHC
LHD
LHD
LHE
LHE
LHF
LHF
LHG
LHG
LHH
LHH
LHI
Package
Shipping†
1.5
NCP662SQ15T1G
NCP662SQ18T1
NCP662SQ18T1G
NCP662SQ25T1
NCP662SQ25T1G
NCP662SQ27T1
NCP662SQ27T1G
NCP662SQ28T1
NCP662SQ28T1G
NCP662SQ30T1
NCP662SQ30T1G
NCP662SQ33T1
NCP662SQ33T1G
NCP662SQ50T1
NCP662SQ50T1G
NCP663SQ15T1
NCP663SQ15T1G
NCP663SQ18T1
NCP663SQ18T1G
NCP663SQ25T1
NCP663SQ25T1G
NCP663SQ27T1
NCP663SQ27T1G
NCP663SQ28T1
NCP663SQ28T1G
NCP663SQ30T1
NCP663SQ30T1G
NCP663SQ33T1
NCP663SQ33T1G
NCP663SQ50T1
NCP663SQ50T1G
1.5
1.8
1.8
2.5
2.5
2.7
2.7
3000 Units/
8″ Tape & Reel
SC82−AB
2.8
2.8
3.0
3.0
3.3
3.3
5.0
5.0
1.5
1.5
1.8
1.8
2.5
2.5
LHI
2.7
LHJ
2.7
LHJ
SC82−AB
3000 Units/
8″ Tape & Reel
2.8
LHK
LHK
LHL
LHL
LHM
LHM
LHN
LHN
2.8
3.0
3.0
3.3
3.3
5.0
5.0
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
8
NCP662, NCV662, NCP663, NCV663
ORDERING INFORMATION
Nominal
Output Voltage
Device
NCV662SQ15T1
Marking
LGY
LGY
LGZ
LGZ
LHA
LHA
LHB
LHB
LHC
LHC
LHD
LHD
LHE
LHE
LHF
LHF
LHG
LHG
LHH
LHH
LHI
Package
Shipping†
1.5
NCV662SQ15T1G
NCV662SQ18T1
NCV662SQ18T1G
NCV662SQ25T1
NCV662SQ25T1G
NCV662SQ27T1
NCV662SQ27T1G
NCV662SQ28T1
NCV662SQ28T1G
NCV662SQ30T1
NCV662SQ30T1G
NCV662SQ33T1
NCV662SQ33T1G
NCV662SQ50T1
NCV662SQ50T1G
NCV663SQ15T1
NCV663SQ15T1G
NCV663SQ18T1
NCV663SQ18T1G
NCV663SQ25T1
NCV663SQ25T1G
NCV663SQ27T1
NCV663SQ27T1G
NCV663SQ28T1
NCV663SQ28T1G
NCV663SQ30T1
NCV663SQ30T1G
NCV663SQ33T1
NCV663SQ33T1G
NCV663SQ50T1
NCV663SQ50T1G
1.5
1.8
1.8
2.5
2.5
2.7
2.7
3000 Units/
8″ Tape & Reel
SC82−AB
2.8
2.8
3.0
3.0
3.3
3.3
5.0
5.0
1.5
1.5
1.8
1.8
2.5
2.5
LHI
2.7
LHJ
2.7
LHJ
SC82−AB
3000 Units/
8″ Tape & Reel
2.8
LHK
LHK
LHL
LHL
LHM
LHM
LHN
LHN
2.8
3.0
3.0
3.3
3.3
5.0
5.0
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
9
NCP662, NCV662, NCP663, NCV663
PACKAGE DIMENSIONS
SC82−AB (SC70−4)
SQ SUFFIX
CASE 419C−02
ISSUE C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. 419C−01 OBSOLETE. NEW STANDARD IS
419C−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
A
G
C
D 3 PL
N
MILLIMETERS
DIM MIN MAX
INCHES
MIN
MAX
0.087
0.053
0.043
0.016
0.020
0.059
0.004
0.010
−−−
4
1
3
2
A
B
C
D
F
1.8
1.15
0.8
2.2 0.071
1.35 0.045
1.1 0.031
0.4 0.008
0.5 0.012
1.5 0.043
0.1 0.000
0.26 0.004
K
B
F
S
0.2
0.3
G
H
J
1.1
0.0
H
J
0.10
0.1
K
L
−−−
0.004
0.002 BSC
0.008 REF
0.07 0.09
L
0.05 (0.002)
0.05 BSC
0.2 REF
1.8
N
S
2.4
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
For additional information, please contact your
local Sales Representative.
NCP662/D
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明