NCD5702DR2G [ONSEMI]
High Current IGBT Gate Driver;型号: | NCD5702DR2G |
厂家: | ONSEMI |
描述: | High Current IGBT Gate Driver 栅 双极性晶体管 |
文件: | 总18页 (文件大小:424K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NCD5702
High Current IGBT Gate
Driver
The NCD5702 is a high−current, high−performance stand−alone
IGBT driver for high power applications that include solar inverters,
motor control and uninterruptible power supplies. The device offers a
cost−effective solution by eliminating many external components.
Device protection features include Active Miller Clamp, accurate
UVLO, EN input, DESAT protection and Active open−drain FAULT
output. The driver also features an accurate 5.0 V output and separate
high and low (VOH and VOL) driver outputs for system design
convenience. The driver is designed to accommodate a wide voltage
range of bias supplies including unipolar and bipolar voltages. It is
available in a 16−pin SOIC package.
www.onsemi.com
MARKING
DIAGRAM
NCD5702DR2G
AWLYWW
SOIC−16
D SUFFIX
CASE 751B
Features
A
WL
Y
WW
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
• High Current Output (+4/−6 A) at IGBT Miller Plateau Voltages
• Low Output Impedance of VOH & VOL for Enhanced IGBT Driving
• Short Propagation Delays with Accurate Matching
• Direct Interface to Digital Isolator/Opto−coupler/Pulse Transformer
for Isolated Drive, Logic Compatibility for Non−isolated Drive
• Active Miller Clamp to Prevent Spurious Gate Turn−on
• DESAT Protection with Programmable Delay
PIN CONNECTIONS
• Enable Input for Independent Driver Control
1
CLAMP
VEEA
VEE
EN
VIN
16
15
14
13
12
11
10
9
• Tight UVLO Thresholds for Bias Flexibility
• Wide Bias Voltage Range including Negative VEE Capability
• This Device is Pb−Free, Halogen−Free and RoHS Compliant
2
3
4
5
6
VREF
FLT
GND
Typical Applications
GNDA
NC
VOL
• Solar Inverters
• Motor Control
• Uninterruptible Power Supplies (UPS)
• Rapid Shutdown for Photovoltaic Systems
VOH
VCC
RSVD
NC
7
8
DESAT
(Top View)
VREF
EN
DESAT
VCC
ORDERING INFORMATION
See detailed ordering and shipping information on page 6 of
this data sheet.
VCC
VOH
VOL
CLAMP
GND
VIN
FLT
VEE
VEE
Figure 1. Simplified Application Schematic
© Semiconductor Components Industries, LLC, 2017
1
Publication Order Number:
April, 2018 − Rev. 1
NCD5702/D
NCD5702
Figure 2. Detailed Block Diagram
Figure 3. Simplified Block Diagram
www.onsemi.com
2
NCD5702
Table 1. PIN FUNCTION DESCRIPTION
Pin Name
No.
I/O/x
Description
EN
1
I
Enable input allows additional gating of VOH and VOL, and can be used when the driver output
needs to be turned off independent of the Microcontroller input. EN is internally clamped to 5 V and
has a pull−up resistor of 1 MW.
VIN
2
I
Input signal to control the output. In applications which require galvanic isolation, VIN is generated
at the opto output, the pulse transformer secondary or the digital isolator output. VOIH/VOL signal is
in phase with VIN. VIN is internally clamped to 5 V and has a pull−down resistor of 1 MW to ensure
that output is low in the absence of an input signal. A minimum pulse−width is required at VIN be-
fore VOH/VOL are activated.
VREF
FLT
3
4
O
O
5 V Reference generated within the driver is brought out to this pin for external bypassing and for
powering low bias circuits (such as digital isolators).
Fault open drain output (active low) that allows communication to the main controller that the driver
has encountered a fault condition and has deactivated the output. Open drain allows easy setting of
(inactive) high level and parallel connection of multiple fault signals.
Connect to 10k pull−up resistor recommended. Truth Table is provided in the datasheet to indicate
conditions under which this signal is asserted. Capable of driving optos or digital isolators when
isolation is required.
GNDA
5
x
This pin provides a convenient connection point for bypass capacitors (e.g REF) on the left side of
the package.
NC
6,8
7
x
x
I
Pins not internally connected.
RSVD
DESAT
Reserved. No connection is allowed.
9
Input for detecting the desaturation of IGBT due to a fault condition. A capacitor connected to this
pin allows a programmable blanking delay every ON cycle before DESAT fault is processed, thus
preventing false triggering.
VCC
10
x
Positive bias supply for the driver. The operating range for this pin is from UVLO to the maximum. A
good quality bypassing capacitor is required from this pin to GND and should be placed close to the
pins for best results.
VOH
VOL
11
12
O
O
Driver high output that provides the appropriate drive voltage and source current to the IGBT gate.
Driver low output that provides the appropriate drive voltage and sink current to the IGBT gate. VOL
is actively pulled low during start−up and under Fault conditions.
GND
VEE
13
14
x
x
This pin should connect to the IGBT Emitter with a short trace. All power pin bypass capacitors
should be referenced to this pin and kept at a short distance from the pin.
A negative voltage with respect to GND can be applied to this pin and that will allow VOL to go to a
negative voltage during OFF state. A good quality bypassing capacitor is needed from VEE to GND.
If a negative voltage is not applied or available, this pin must be connected to GND.
VEEA
15
16
x
Analog version of the VEE pin for any signal trace connection. VEE and VEEA are internally con-
nected.
CLAMP
I/O
Provides clamping for the IGBT gate during the off period to protect it from parasitic turn−on. To be
tied directly to IGBT gate with minimum trace length for best results.
www.onsemi.com
3
NCD5702
Table 2. ABSOLUTE MAXIMUM RATINGS (Note 1)
Parameter
Symbol
Minimum
Maximum
Unit
V
Differential Power Supply
Positive Power Supply
Negative Power Supply
Gate Output High
V
−V (V )
EE max
0
36
22
CC
V
−GND
−GND
−0.3
−18
V
CC
V
0.3
V
EE
V
−GND
−GND
V + 0.3
CC
V
OH
Gate Output Low
V
V
V
EE
− 0.3
V
OL
Input Voltage
−GND
−0.3
5.5
5.5
+ 0.3
V
IN
Enable Voltage
V
EN
−GND
−0.3
−0.3
V
DESAT Voltage
V
−GND
DESAT
V
CC
V
FLT Current
Sink
mA
I
20
FLT−SINK
Power Dissipation
SO−16 package
PD
mW
900
150
Maximum Junction Temperature
Storage Temperature Range
T
°C
°C
kV
V
J(max)
TSTG
−65 to 150
ESD Capability, Human Body Model (Note 2)
ESD Capability, Machine Model (Note 2)
Moisture Sensitivity Level
ESDHBM
ESDMM
MSL
4
200
1
−
Lead Temperature Soldering Reflow
(SMD Styles Only), Pb−Free Versions (Note 3)
T
SLD
260
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114)
ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115)
Latchup Current Maximum Rating: ≤ 100 mA per JEDEC standard: JESD78, 25°C
3. For information, please refer to our Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
Table 3. THERMAL CHARACTERISTICS
Parameter
Symbol
Value
Unit
Thermal Characteristics, SOIC−16 (Note 4)
Thermal Resistance, Junction−to−Air (Note 5)
°C/W
R
145
θJA
4. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2
2
5. Values based on copper area of 100 mm (or 0.16 in ) of 1 oz copper thickness and FR4 PCB substrate.
Table 4. OPERATING RANGES (Note 6)
Parameter
Differential Power Supply
Symbol
−V (V )
max
Min
Max
30
20
0
Unit
V
V
CC
EE
Positive Power Supply
Negative Power Supply
Input Voltage
V
CC
UVLO
−15
0
V
V
EE
V
V
5
V
IN
EN
on
Enable Voltage
V
0
5
V
Input Pulse Width
Ambient Temperature
t
40
ns
°C
T
A
−40
125
6. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
www.onsemi.com
4
NCD5702
Table 5. ELECTRICAL CHARACTERISTICS V = 15 V, V = 0 V, Kelvin GND connected to V . For typical values T = 25°C,
CC
EE
EE
A
for min/max values, T is the operating ambient temperature range that applies, unless otherwise noted.
A
Parameter
Test Conditions
Symbol
Min
Typ
Max
Unit
LOGIC INPUT and OUTPUT
Input Threshold Voltages
Pulse−Width = 150 ns, V = 5 V
V
EN
High−state (Logic 1) Required Voltage applied to get output go high
Low−state (Logic 0) Required Voltage applied to get output go low
V
4.3
1.2
IN−H1
V
0.75
3.7
IN−L1
No state change
Voltage applied without change in output state
V
IN−NC
Enable Threshold Voltages
High−state
V
= 5 V
V
IN
Voltage applied to get output go high
Voltage applied to get output go low
V
4.3
EN−H
Low−state
V
0.75
EN−L
Enable Current
High−state
mA
mA
ns
V
V
/V
= 4.5 V
= 0.5 V
I
1
IN−H EN−H
EN−H
Low−state
/V
I
10
IN−L EN−L
EN−L
Input Current
High−state
Low−state
V
V
/V
= 4.5 V
= 0.5 V
I
10
1
IN−H EN−H
IN−H
/V
I
IN−L
IN−L EN−L
Input Pulse−Width
Voltage thresholds consistent with input
specs
No Response at the Output
t
t
15
on−min1
Guaranteed Response at the
Output
35
on−min2
FLT Threshold Voltage
Low State
V
(I
= 15 mA)
V
FLT−L
0.5
1.0
FLT−SINK
High−state
Pull−up Externally
V
FLT−H
V
CC
+0.3
DRIVE OUTPUT
Output Low State
V
V
I
I
I
= 200 mA, T = 25°C
V
0.1
0.2
0.8
0.2
sink
sink
sink
A
OL1
OL2
OL3
= 200 mA, T = −40°C to 125°C
V
0.5
1.2
A
= 1.0 A, T = 25°C
V
A
Output High State
I
src
I
src
I
src
= 200 mA, T = 25°C
V
14.5
14.2
13.8
14.8
14.7
14.1
A
OH1
OH2
OH3
= 200 mA, T = −40°C to 125°C
V
V
A
= 1.0 A, T = 25°C
A
Peak Driver Current, Sink
(Note 7)
R
= 0.1 W, V = 15 V, V = −8 V
A
A
G
O
O
CC
EE
V
V
= 13 V
= 9 V (near Miller Plateau)
I
I
6.8
6.1
PK−snk1
PK−snk2
Peak Driver Current, Source
(Note 7)
R
= 0.1 W, V = 15 V, V = −8 V
G
O
O
CC
EE
V
V
= −5 V
= 9 V (near Miller Plateau)
I
7.8
4.0
PK−src1
I
PK−src2
DYNAMIC CHARACTERISTICS
Turn−on Delay
(see timing diagram)
Positive input pulse width = 10 ms
Negative input pulse width = 10 ms
For input or output pulse width > 150 ns,
t
t
45
45
59
54
75
75
ns
ns
ns
pd−on
Turn−off Delay
(see timing diagram)
pd−off
Propagation Delay Distortion
(=t
− t
)
T = 25°C
T = −40°C to 125°C
A
t
−5
5
15
25
pd−on pd−off
A
distort1
t
−25
distort2
Prop Delay Distortion between
Parts (Note 7)
t
−30
0
30
ns
ns
distort −tot
Rise Time (Note 7)
(see timing diagram)
C
= 1.0 nF
t
9.2
load
rise
7. Values based on design and/or characterization.
www.onsemi.com
5
NCD5702
Table 5. ELECTRICAL CHARACTERISTICS V = 15 V, V = 0 V, Kelvin GND connected to V . For typical values T = 25°C,
CC
EE
EE
A
for min/max values, T is the operating ambient temperature range that applies, unless otherwise noted.
A
Parameter
Test Conditions
Symbol
Min
Typ
Max
Unit
DYNAMIC CHARACTERISTICS
Fall Time (Note 7)
(see timing diagram)
C
= 1.0 nF
t
7.9
12
ns
ms
ns
ms
load
fall
Delay from FLT under UVLO/
TSD to VOL
t
t
10
15
d1−OUT
Delay from DESAT to VOL
(Note 7)
220
7.3
d2−OUT
Delay from UVLO/TSD to FLT
(Note 7)
t
d3−FLT
MILLER CLAMP
Clamp Voltage
I
= 500 mA, T = 25°C
V
1.2
2.0
1.4
2.2
V
V
sink
A
clamp
I
= 500 mA, T = −40°C to 125°C
sink
A
Clamp Activation Threshold
DESAT PROTECTION
DESAT Threshold Voltage
Blanking Charge Current
Blanking Discharge Current
UVLO
V
1.8
2.2
MC−THR
V
6.0
6.35
0.24
30
7.0
V
DESAT−THR
I
0.20
0.28
mA
mA
DESAT−CHG
I
DESAT−DIS
UVLO Startup Voltage
UVLO Disable Voltage
UVLO Hysteresis
V
13.2
12.2
13.5
12.5
1.0
13.8
12.8
V
V
V
UVLO−OUT−ON
V
UVLO−OUT−OFF
V
UVLO−HYST
VREF
Voltage Reference
I
= 10 mA
V
4.85
100
5.00
5.15
20
V
REF
REF
Reference Output Current
(Note 7)
I
mA
REF
Recommended Capacitance
C
nF
VREF
SUPPLY CURRENT
Current Drawn from V
V
= 15 V
I
0.9
1.5
mA
mA
CC
EE
CC
CC−SB
Standby (No load on output, FLT, VREF)
Current Drawn from V
V
EE
= −10 V
I
−0.2
−0.14
EE−SB
Standby (No load on output, FLT, VREF)
THERMAL SHUTDOWN
Thermal Shutdown Temperature
(Note 7)
T
188
33
°C
°C
SD
Thermal Shutdown Hysteresis
(Note 7)
T
SH
7. Values based on design and/or characterization.
ORDERING INFORMATION
Device
†
Package
Shipping
NCD5702DR2G
SO−16
(Pb−Free)
2500 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
6
NCD5702
TYPICAL CHARACTERISTICS
80
70
60
80
70
t
t
pd−on
60
pd−off
50
40
50
40
−40 −20
0
20
40
60
80
100 120
−40 −20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 4. Propagation Delay vs. Temperature
Figure 5. Enable to Output Low Delay
20
15
10
5
15
14
13
12
t
fall
t
rise
11
10
0
−40 −20
0
20
40
60
80
100 120
−40 −20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 6. Fault to Output Low Delay
Figure 7. Output Rise/Fall Time
8
7
8
7
6
6
5
4
3
2
5
4
3
2
1
0
1
0
−5
0
5
10
15
−5
0
5
10
V (V, V = 15 V, V = −8 V)
O
15
V
O
(V, V = 15 V, V = −8 V)
CC
EE
CC
EE
Figure 8. Output Source Current vs. Output
Voltage
Figure 9. Output Sink Current vs. Output
Voltage
www.onsemi.com
7
NCD5702
TYPICAL CHARACTERISTICS
5.05
5.04
5.03
5.02
5.01
5.00
4.99
4.98
4.97
5.05
5.04
5.03
5.02
5.01
5.00
4.99
4.98
4.97
V
@ I
= 0 mA
REF
REF
V
REF
@ I
= 10 mA
REF
4.96
4.95
4.96
4.95
0
2
4
6
8
10
−40 −20
0
20
40
60
80
100 120
I
(mA)
TEMPERATURE (°C)
REF
Figure 10. VREF Voltage vs. Current
Figure 11. VCLAMP at 0.5 A
260
6.5
6.4
250
240
6.3
6.2
−40 −20
0
20
40
60
80
100 120
−40 −20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 12. DESAT Charge Current vs.
Temperature
Figure 13. DESAT Threshold Voltage vs.
Temperature
15
10
20
15
10
5
UVLO−OUT−OFF
UVLO−OUT−ON
5
0
0
−5
10
11
12
13
14
15
0
1
2
3
4
5
V
CC
, SUPPLY VOLTAGE (V)
V
(V)
IN
Figure 14. UVLO Threshold Voltages
Figure 15. VO vs. VIN at 255C
(VCC = 15 V, VEE = 0 V)
www.onsemi.com
8
NCD5702
TYPICAL CHARACTERISTICS
1.0
2.5
2.0
0.5
1.5
1.0
0.5
0
−40 −20
0
20
40
60
80
100 120
−40 −20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 16. Fault Output, Sinking 15 mA
Figure 17. VCLAMP at 0.5 A
1.4
1.2
1.0
I
CC
0.8
0.6
0.4
I
EE
0.2
0
0
20
40
60
80
100
FREQUENCY (kHz)
Figure 18. Supply Current vs. Switching
Frequency (VCC = 15 V, VEE = −10 V, 255C)
www.onsemi.com
9
NCD5702
Applications and Operating Information
This section lists the details about key features and
operating guidelines for the NCD5702.
High Drive Current Capability
The NCD5702 driver family is equipped with many
features which facilitate a superior performance IGBT
driving circuit. Foremost amongst these features is the high
drive current capability. The drive current of an IGBT driver
is a function of the differential voltage on the output pin
(V −VOH for source current, VOL−V for sink current)
CC
EE
as shown in Figure 19. Figure 19 also indicates that for a
given VOH/VOL value, the drive current can be increased
by using higher V /V power supply). The drive current
CC EE
Figure 19. Output Current vs. Output Voltage Drop
tends to drop off as the output voltage goes up (for turn−on
event) or goes down (for turn−off event). As explained in
many IGBT application notes, the most critical phase of
IGBT switching event is the Miller plateau region where the
gate voltage remains constant at a voltage (typically in 9−11
V range depending on IGBT design and the collector
current), but the gate drive current is used to
When driving larger IGBTs for higher current
applications, the drive current requirement is higher, hence
lower R is used. Larger IGBTs typically have high input
G
capacitance. On the other hand, if the NCD5702 is used to
drive smaller IGBT (lower input capacitance), the drive
current requirement is lower and a higher R is used. Thus,
G
charge/discharge the Miller capacitance (C ). By
GC
for most typical applications, the driver load RC time
constant remains fairly constant. Caution must be exercised
when using the NCD5702 with a very low load RC time
constant. Such a load may trigger internal protection
circuitry within the driver and disable the device. Figure 20
shows the recommended minimum gate resistance as a
function of IGBT gate capacitance and gate drive trace
inductance.
providing a high drive current in this region, a gate driver can
significantly reduce the duration of the phase and help
reducing the switching losses. The NCD5702 addresses this
requirement by providing and specifying a high drive
current in the Miller plateau region. Most other gate driver
ICs merely specify peak current at the start of switching –
which may be a high number, but not very relevant to the
application requirement. It must be remembered that other
considerations such as EMI, diode reverse recovery
performance, etc., may lead to a system level decision to
trade off the faster switching speed against low EMI and
reverse recovery. However, the use of NCD5702 does not
preclude this trade−off as the user can always tune the drive
current by employing external series gate resistor. Important
thing to remember is that by providing a high internal drive
current capability, the NCD5702 facilitates a wide range of
gate resistors. Another value of the high current at the Miller
plateau is that the initial switching transition phase is shorter
and more controlled. Finally, the high gate driver current
(which is facilitated by low impedance internal FETs),
ensures that even at high switching frequencies, the power
dissipation from the drive circuit is primarily in the external
series resistor and more easily manageable. Experimental
results have shown that the high current drive results in
Figure 20. Recommended Minimum Gate Resistance
as a Function of IGBT Gate Capacitance
reduced turn−on energy (E ) for the IGBT switching.
ON
www.onsemi.com
10
NCD5702
Gate Voltage Range
controller to initiate a more orderly/sequenced shutdown. In
case the controller fails to do so, the driver output shutdown
The negative drive voltage for gate (with respect to GND,
or Emitter of the IGBT) is a robust way to ensure that the gate
voltage does not rise above the threshold voltage due to the
Miller effect. In systems where the negative power supply is
available, the VEE option offered by NCD5702 allows not
only a robust operation, but also a higher drive current for
turn−off transition. Adequate bypassing between VEE pin
and GND pin is essential if this option is used.
ensures IGBT protection after t
.
d1−OUT
The V range for the NCD5702 is quite wide and allows
CC
the user the flexibility to optimize the performance or use
available power supplies for convenience.
Under Voltage Lock Out (UVLO)
This feature ensures reliable switching of the IGBT
connected to the driver output. At the start of the driver’s
operation when V is applied to the driver, the output
CC
remains turned−off. This is regardless of the signals on V
IN
until the V
(V
V
reaches the UVLO Output Enabled
CC
UVLO−OUT−ON
UVLO−OUT−ON
) level. After the V
rises above the
CC
level, the driver is in normal operation. The
state of the output is controlled by signal at V .
IN
If the V
falls below the UVLO Output Disabled
CC
(V ) level during the normal operation of the
UVLO−OUT−OFF
driver, the Fault output is activated and the output is shut−down
(after a delay) and remains in this state. The driver output
does not start to react to the input signal on V until the V
IN
CC
Figure 21. UVLO Function and Limits
rises above the V
again. The waveform
UVLO−OUT−ON
showing the UVLO behavior of the driver is in Figure 21.
In an IGBT drive circuit, the drive voltage level is
Timing Delays and Impact on System Performance
The gate driver is ideally required to transmit the input
signal pulse to its output without any delay or distortion. In
the context of a high−power system where IGBTs are
typically used, relatively low switching frequency (in tens of
kHz) means that the delay through the driver itself may not
be as significant, but the matching of the delay between
different drivers in the same system as well as between
different edges has significant importance. With reference to
Figure 22(a), two input waveforms are shown. They are
typical complementary inputs for high−side (HS) and
low−side (LS) of a half−bridge switching configuration. The
dead−time between the two inputs ensures safe transition
between the two switches. However, once these inputs are
through the driver, there is potential for the actual gate
voltages for HS and LS to be quite different from the
intended input waveforms as shown in Figure 22(a). The end
result could be a loss of the intended dead−time and/or
pulse−width distortion. The pulse−width distortion can
create an imbalance that needs to be corrected, while the loss
of dead−time can eventually lead to cross−conduction of the
switches and additional power losses or damage to the
system.
important for drive circuit optimization. If V
UVLO−OUT−OFF
is too low, it will lead to IGBT being driven with insufficient
gate voltage. A quick review of IGBT characteristics can
reveal that driving IGBT with low voltage (in 10−12 V
range) can lead to a significant increase in conduction loss.
So, it is prudent to guarantee V
at a
UVLO−OUT−OFF
reasonable level (above 12 V), so that the IGBT is not forced
to operate at a non−optimum gate voltage. On the other hand,
having a very high drive voltage ends up increasing
switching losses without much corresponding reduction in
conduction loss. So, the V
value should not
UVLO−OUT−ON
be too high (generally, well below 15 V). These conditions
lead to a tight band for UVLO enable and disable voltages,
while guaranteeing a minimum hysteresis between the two
values to prevent hiccup mode operation. The NCD5702
meets these tight requirements and ensures smooth IGBT
operation. It ensures that a 15 V supply with 8% tolerance
will work without degrading IGBT performance, and
guarantees that a fault will be reported and the IGBT will be
turned off when the supply voltage drops below 12.2 V.
A UVLO event (V voltage going below V
)
CC
UVLO−OUT−OFF
also triggers activation of FLT output after a delay of t
.
d3−FLT
The NCD5702 driver is designed to address these timing
challenges by providing a very low pulse−width distortion
and excellent delay matching. As an example, the delay
This indicates to the controller that the driver has
encountered an issue and corrective action needs to be taken.
However, a nominal delay t
= 12 ms is introduced
d1−OUT
matching is guaranteed to t
= 25 ns while many
DISTORT2
between the initiation of the FLT output and actual turning
off of the output. This delay provides adequate time for the
of competing driver solutions can be >250 ns.
www.onsemi.com
11
NCD5702
Figure 22(a). Timing Waveforms (Other Drivers)
Figure 22(b). NCD5702 Timing Waveforms
Active Miller Clamp Protection
An alternative way is to provide an additional path from
gate to GND with very low impedance. This is exactly what
Active Miller Clamp protection does. Additional trace from
the gate of the IGBT to the Clamp pin of the gate driver is
This feature is a cost savvy alternative to a negative gate
voltage. The main requirement is to hold the gate of the
turned−off (for example low−side) IGBT below the
threshold voltage during the turn−on of the opposite−side (in
this example high−side) IGBT in the half bridge. The
turn−on of the high−side IGBT causes high dv/dt transition
on the collector of the turned−off low−side IGBT. This high
dv/dt then induces current (Miller current) through the C
capacitance (Miller capacitance) to the gate capacitance of
the low−side IGBT as shown in Figure 23. If the path from
introduced. After the V output has gone below the Active
O
Miler Clamp threshold V
the Clamp pin is shorted
MC−THR
to GND and thus prevents the voltage on the gate of the
IGBT to rise above the threshold voltage as shown in
Figure 24. The Clamp pin is disconnected from GND as
soon as the signal to turn on the IGBT arrives to the gate
driver input. The fact that the Clamp pin is engaged only
GC
gate to GND has critical impedance (caused by R ) the
after the gate voltage drops below the V
threshold
G
MC−THR
Miller current could rise the gate voltage above the threshold
level. As a consequence the low−side IGBT could be turned
on for a few tens or hundreds of nanoseconds. This causes
higher switching losses. One way to avoid this situation is to
use negative gate voltage, but this requires second DC
source for the negative gate voltage.
ensures that the function of this pin does not interfere with
the normal turn−off switching performance that is user
controllable by choice of R .
G
www.onsemi.com
12
NCD5702
Figure 23. Current Path without Miller Clamp
Protection
Figure 24. Current Path with Miller Clamp Protection
Desaturation Protection (DESAT)
At the turned−on output state of the driver, the current
from current source starts to flow to the
This feature monitors the collector−emitter voltage of the
IGBT in the turned−on state. When the IGBT is fully turned
on, it operates in a saturation region. Its collector−emitter
voltage (called saturation voltage) is usually low, well below
3 V for most modern IGBTs. It could indicate an overcurrent
or similar stress event on the IGBT if the collector−emitter
voltage rises above the saturation voltage, after the IGBT is
fully turned on. Therefore the DESAT protection circuit
compares the collector−emitter voltage with a voltage level
I
DESAT−CHG
blanking capacitor C , connected to DESAT pin.
BLANK
Appropriate value of this capacitor has to be selected to
ensure that the DESAT pin voltage does not rise above the
threshold level V
before the IGBT fully turns on.
DESAT−THR
The blanking time is given by following expression.
According to this expression, a 47 pF C will provide
BLANK
a blanking time of (47p *6.5/0.25m =) 1.22 ms.
VDESAT−THR
IDESAT−CHG
t
BLANK + CBLANK
@
V
to check if the IGBT didn’t leave the saturation
DESAT−THR
region. It will activate FLT output and shut down driver
output (thus turn−off the IGBT), if the saturation voltage
After the IGBT is fully turned−on, the I
flows
DESAT−CHG
through the DESAT pin to the series resistor R
and
S−DESAT
rises above the V
. This protection works on
DESAT−THR
through the high voltage diode and then through the
collector and IGBT to the emitter. Care must be taken to
every turn−on phase of the IGBT switching period.
At the beginning of turning−on of the IGBT, the
collector−emitter voltage is much higher than the saturation
voltage level which is present after the IGBT is fully turned
on. It takes almost 1 ms between the start of the IGBT turn−on
and the moment when the collector−emitter voltage falls to
the saturation level. Therefore the comparison is delayed by
a configurable time period (blanking time) to prevent false
triggering of DESAT protection before the IGBT
collector−emitter voltage falls below the saturation level.
select the resistor R
value so that the sum of the
S−DESAT
saturation voltage, drop on the HV diode and drop on the
caused by current I flowing from
R
S−DESAT
DESAT−CHG
DESAT source current is smaller than the DESAT threshold
voltage. Following expression can be used:
V
DESAT−THR u
R
S−DESAT @ IDESAT−CHG ) VF_HV diode ) VCESAT_IGBT
Blanking time is set by the value of the capacitor C
The exact principle of operation of DESAT protection is
described with reference to Figure 25.
.
Important part for DESAT protection to work properly is
the high voltage diode. It must be rated for at least same
voltage as the low side IGBT. The safety margin is
application dependent.
BLANK
At the turned−off output state of the driver, the DESAT pin
is shorted to ground via the discharging transistor (Q ).
Therefore, the inverting input holds the comparator output
at low level.
The typical waveforms for IGBT overcurrent condition
are outlined in Figure 26.
DIS
www.onsemi.com
13
NCD5702
Figure 25. Desaturation Protection Schematic
Figure 26. Desaturation Protection Waveforms
www.onsemi.com
14
NCD5702
Input Signal
The input signal controls the gate driver output. Figure 27
shows the typical connection diagrams for isolated
applications where the input is coming through an
opto−coupler or a pulse transformer.
Figure 27. Opto−coupler or Pulse Transformer At Input
The relationship between gate driver input signal from a
pulse transformer (Figure 28) or opto−coupler (Figure 29)
and the output is defined by many time and voltage values.
The time values include output turn−on and turn−off delays
delay times are defined from 50% of input transition to first
10% of the output transition to eliminate the load
dependency. The input voltage parameters include input
high (V
) and low (V
) thresholds as well as the
IN−H1
IN−L1
(t
and t
), output rise and fall times (t and t )
input range for which no output change is initiated
(V ).
pd−on
pd−off
rise
fall
and minimum input pulse−width (t
). Note that the
on−min
IN−NC
Figure 28. Input and Output Signal Parameters for Pulse Transformer
www.onsemi.com
15
NCD5702
Figure 29. Input and Output Signal Parameters for Opto−coupler
Use of VREF Pin
The NCD5702 provides an additional 5.0 V output
(VREF) that can serve multiple functions. This output is
capable of sourcing up to 10 mA current for functions such
as opto−coupler interface or external comparator interface.
The VREF pin should be bypassed with at least a 100 nF
capacitor (higher the better) irrespective of whether it is
being utilized for external functionality or not. VREF is
highly stable over temperature and line/load variations (see
characteristics curves for details)
Fault Output Pin
This pin provides the feedback to the controller about the
driver operation. The situations in which the FLT signal
becomes active (low value) are summarized in the Table 6.
Table 6. FLT LOGIC TRUTH TABLE
VIN
L
ENABLE
UVLO
Inactive
Inactive
Inactive
Active
DESAT
Internal TSD
VOUT
FLT
Notes
H
H
L
L
L
L
L
L
L
L
H
L
open−drain
open−drain
open−drain
L
Normal operation − Output Low
Normal operation − Output High
Disabled − Output Low, FLT open−drain
H
X
X
X
X
X
L
UVLO activated − FLT Low (t
),
-
d3 FLT
Output Low (t
+ t
d1−OUT
)
-
d3 FLT
L
H
X
Inactive
Inactive
H
X
L
L
L
L
L
DESAT activated (only when V is low)
IN
− Output Low (t ), FLT Low
d2_OUT
X
H
Internal Thermal Shutdown − FLT Low
(t ), Output Low (t + t )
d1−OUT
-
-
d3 FLT
d3 FLT
Thermal Shutdown
Additional Use of Enable Pin
The NCD5702 also offers thermal shutdown function that
is primarily meant to self−protect the driver in the event that
the internal temperature gets excessive. Once the
For some applications, Enable is a useful feature as it
provides the ability to shut down the power stage without
involving the controls such as DSP. It can also be used along
with the VREF pin and a comparator to provide local
shutdown protection at fault conditions such as over
temperature or over current, as illustrated in Figure 30.
temperature crosses the T threshold, the FLT output is
SD
activated after a delay of t
. After a delay of t
d3-FLT d1−OUT
(12 ms), the output is pulled low and many of the internal
circuits are turned off. The 12 ms delay is meant to allow the
controller to perform an orderly shutdown sequence as
appropriate. Once the temperature goes below the second
threshold, the part becomes active again.
www.onsemi.com
16
NCD5702
+V
VREF
Vcc
DESAT
VIN
NCD5702
-
EN
+
VOH
VREF
OT
OC
GND
VOL
VEE
FLT
VEEA
-V
CLAMP
GND
CT
GND
Figure 30. Additional Over Temperature and/or Over Current Shutdown Protection
www.onsemi.com
17
NCD5702
PACKAGE DIMENSIONS
SOIC−16
CASE 751B−05
ISSUE K
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
−A−
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
16
9
8
−B−
P 8 PL
M
S
B
0.25 (0.010)
1
MILLIMETERS
INCHES
MIN
0.386
DIM MIN
MAX
MAX
0.393
0.157
0.068
0.019
0.049
A
B
C
D
F
9.80
3.80
1.35
0.35
0.40
10.00
G
4.00 0.150
1.75 0.054
0.49 0.014
1.25 0.016
F
R X 45
K
_
G
J
1.27 BSC
0.050 BSC
0.19
0.10
0
0.25 0.008
0.25 0.004
0.009
0.009
7
K
M
P
R
C
7
0
_
_
_
_
−T−
SEATING
PLANE
5.80
0.25
6.20 0.229
0.50 0.010
0.244
0.019
J
M
D
16 PL
M
S
S
A
0.25 (0.010)
T
B
SOLDERING FOOTPRINT*
8X
6.40
16X
1.12
1
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
◊
NCD5702/D
相关型号:
©2020 ICPDF网 联系我们和版权申明