MM74HC02MX [ONSEMI]
四路 2 输入 NOR 门极;型号: | MM74HC02MX |
厂家: | ONSEMI |
描述: | 四路 2 输入 NOR 门极 栅 光电二极管 逻辑集成电路 触发器 |
文件: | 总7页 (文件大小:279K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATA SHEET
www.onsemi.com
Quad 2-Input NOR Gate
MM74HC02ꢀ
14
14
1
1
SOIC−14 NB,
CASE 751A−0.3
TSSOP−14,
CASE 948G−01
General Description
The MM74HC02 NOR gates utilize advanced silicon−gate CMOS
technology to achieve operating speeds similar to LS−TTL gates
with the low power consumption of standard CMOS integrated
circuits. All gates have buffered outputs, providing high noise
immunity and the ability to drive 10 LS−TTL loads. The 74HC logic
family is functionally as well as pin−out compatible with the standard
74LS logic family. All inputs are protected from damage due to static
MARKING DIAGRAM
14
14
HC
HC02A
02A
AWLYWW
ALYW
G
G
discharge by internal diode clamps to V and ground.
CC
1
1
Features
• Typical Propagation Delay: 8 ns
HC02A
A
WL, L
Y
WW, YW = Work Week
G
= Specific Device Code
= Assembly Location
= Wafer Lot Number
= Year
• Wide Power Supply Range: 2 V to 6 V
• Low Quiescent Supply Current: 20 mA Maximum (74HC Series)
• Moisture Level Sensitivity 1
= Pb−Free Package
• Low Input Current: 1 mA Maximum
• High Output Current: 4 mA Minimum
• This Device is Pb−Free and Halide Free
(Note: Microdot may be in either location)
ABSOLUTE MAXIMUM RATINGS (Note 1)
CONNECTION DIAGRAM
Symbol
Parameter
Supply Voltage
Rating
Unit
V
Pin Assignment for SOIC and TSSOP
V
CC
−0.5 to +7.0
V
IN
DC Input Voltage
−0.5 to V +0.5
V
CC
V
OUT
DC Output Voltage
−0.5 to V +0.5
V
CC
I , I
Clamp Diode Current
DC Output Current, per pin
20
25
50
mA
mA
mA
IK OK
I
OUT
I
DC V or GND Current,
CC
CC
per pin
T
Storage Temperature Range
Power Dissipation (Note 2)
S.O. Package only
−65 to +150
600
°C
STG
P
mW
D
LOGIC DIAGRAM
500
T
L
Lead Temperature
(Soldering 10 seconds)
260
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the
device. If any of these limits are exceeded, device functionality should not be
assumed, damage may occur and reliability may be affected.
1. Unless otherwise specified all voltages are referenced to ground.
2. Power dissipation temperature derating − plastic “N” package: –12 mW/°C
from 65°C to 85°C.
ORDERING INFORMATION
See detailed ordering and shipping information on page 3 of
this data sheet.
© Semiconductor Components Industries, LLC, 1983
1
Publication Order Number:
October, 2022 − Rev. 2
MM74HC02/D
MM74HC02
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
2
Max
Unit
V
V
CC
Supply Voltage
6
V
IN
, V
DC Input or Output Voltage
Operating Temperature Range
Input Rise or Fall Times
0
V
CC
V
OUT
T
A
−40
−
+85
1000
500
°C
ns
t , t
r
V
CC
V
CC
V
CC
= 2.0 V
= 4.5 V
= 6.0 V
f
−
−
400
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
DC ELECTRICAL CHARACTERISTICS (Note 3)
T
= −40°C
T = −55°C
A
to 125°C
A
to 85°C
T
A
= 25°C
Typ.
−
Guaranteed Limits
Symbol
Parameter
V
CC
(V)
Conditions
Unit
V
IH
Minimum HIGH Level
Input Voltage
2.0
1.50
1.50
3.15
4.20
0.50
1.35
1.80
1.9
1.50
3.15
4.20
0.50
1.35
1.80
1.9
V
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
4.5
−
3.15
4.20
0.50
1.35
1.80
1.9
−
V
IL
Maximum LOW Level
Input Voltage
−
V
V
−
−
V
OH
Minimum HIGH Level
Output Voltage
V
= V or V ,
2.0
4.5
6.0
4.20
IN
IH
IL
⎮I
⎪ ≤ 20 mA
OUT
4.4
4.4
4.4
5.9
5.9
5.9
V
IN
= V or V ,
3.98
3.84
3.70
IH
IL
⎮I
⎪ ≤ 4.0 mA
OUT
6.0
V
= V or V ,
OUT
5.70
5.48
5.34
5.20
IN
IH
IL
⎮I
⎪ ≤ 5.2 mA
V
OL
Maximum LOW Level
Output Voltage
2.0
4.5
6.0
4.5
V
= V or V
IL
OUT
0
0
0.1
0.1
0.1
0.1
0.1
0.1
V
IN
IH
⎮I
⎪ ≤ 20 mA
0
0.1
0.1
0.1
V
IN
= V or V
IL
0.20
0.26
0.33
0.40
IH
⎮I
⎪ ≤ 4.0 mA
OUT
6.0
V
= V or V
IL
OUT
0.20
0.26
0.33
0.40
IN
IH
⎮I
⎪ ≤ 5.2 mA
I
Maximum Input Current
6.0
6.0
V
V
= V or GND
−
−
0.1
2.0
1.0
20
1.0
40
mA
mA
IN
IN
CC
I
Maximum Quiescent
Supply Current
= V or GND,
CC
= 0 mA
CC
IN
I
OUT
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
3. For a power supply of 5 V 10% the worst case output voltages (V , and V ) occur for HC at 4.5 V. Thus the 4.5 V values should be used
OH
OL
when designing with this supply. Worst case V and V occur at V = 5.5 V and 4.5 V respectively. (The V value at 5.5 V is 3.85 V.) The
IH
IL
CC
IH
worst case leakage current (I , I , and I ) occur for CMOS at the higher voltage and so the 6.0 V values should be used.
IN CC
OZ
AC ELECTRICAL CHARACTERISTICS
(V = 5 V, T = 25°C, C = 15 pF, t = t = 6 ns)
CC
A
L
r
f
Symbol
Parameter
Conditions
Typ.
Guaranteed Limit
Unit
t
, t
Maximum Propagation Delay
8
15
ns
PHL PLH
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
2
MM74HC02
AC ELECTRICAL CHARACTERISTICS
(V = 2.0 V to 6.0 V, C = 50 pF, t = t = 6 ns, unless otherwise specified)
CC
L
r
f
T
A
= 25°C
T
= −40°C
T = −55°C
A
to 125°C
A
to 85°C
Typ.
45
9
Guaranteed Limits
Symbol
Parameter
V
CC
(V)
Conditions
Unit
t
, t
Maximum Propagation
Delay
2.0
90
18
15
75
15
13
−
113
23
19
95
19
16
−
134
27
23
110
22
19
−
ns
PHL PLH
4.5
6.0
2.0
4.5
6.0
8
t
, t
Maximum Output
Rise and Fall Time
30
8
ns
TLH THL
7
C
Power Dissipation
Capacitance (Note 4)
(per gate)
20
pF
pF
PD
C
Maximum Input
Capacitance
5
10
10
10
IN
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2
4. C determines the no load dynamic power consumption, P = C
V
f + I V , and the no load dynamic current consumption,
PD
D
PD CC
CC CC
I
= C
V
f + I
.
S
PD CC
CC
ORDERING INFORMATION
Device
†
Package
Shipping
MM74HC02M
SOIC−14 NB
55 Units / Tube
2500 / Tape & Reel
96 Units / Tube
(Pb−Free and Halide Free)
MM74HC02MX
MM74HC02MTC
MM74HC02MTCX
TSSOP−14
(Pb−Free and Halide Free)
2500 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
NOTE: All packages are lead free per JEDEC: J−STD−020B standard.
www.onsemi.com
3
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SOIC−14 NB
CASE 751A−03
ISSUE L
14
1
DATE 03 FEB 2016
SCALE 1:1
NOTES:
D
A
B
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION
SHALL BE 0.13 TOTAL IN EXCESS OF AT
MAXIMUM MATERIAL CONDITION.
4. DIMENSIONS D AND E DO NOT INCLUDE
MOLD PROTRUSIONS.
14
8
7
A3
E
H
5. MAXIMUM MOLD PROTRUSION 0.15 PER
SIDE.
L
DETAIL A
1
MILLIMETERS
DIM MIN MAX
INCHES
MIN MAX
13X b
M
M
B
0.25
A
A1
A3
b
D
E
1.35
0.10
0.19
0.35
8.55
3.80
1.75 0.054 0.068
0.25 0.004 0.010
0.25 0.008 0.010
0.49 0.014 0.019
8.75 0.337 0.344
4.00 0.150 0.157
M
S
S
B
0.25
C A
DETAIL A
h
A
X 45
_
e
H
h
L
1.27 BSC
0.050 BSC
6.20 0.228 0.244
0.50 0.010 0.019
1.25 0.016 0.049
5.80
0.25
0.40
0
0.10
M
A1
e
M
7
0
7
_
_
_
_
SEATING
PLANE
C
GENERIC
MARKING DIAGRAM*
SOLDERING FOOTPRINT*
6.50
14
14X
1.18
XXXXXXXXXG
AWLYWW
1
1
XXXXX = Specific Device Code
A
WL
Y
= Assembly Location
= Wafer Lot
= Year
1.27
PITCH
WW
G
= Work Week
= Pb−Free Package
14X
0.58
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
STYLES ON PAGE 2
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DOCUMENT NUMBER:
DESCRIPTION:
98ASB42565B
SOIC−14 NB
PAGE 1 OF 2
onsemi and
are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves
the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation
special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
SOIC−14
CASE 751A−03
ISSUE L
DATE 03 FEB 2016
STYLE 1:
STYLE 2:
CANCELLED
STYLE 3:
STYLE 4:
PIN 1. NO CONNECTION
2. CATHODE
PIN 1. COMMON CATHODE
2. ANODE/CATHODE
3. ANODE/CATHODE
4. NO CONNECTION
5. ANODE/CATHODE
6. NO CONNECTION
7. ANODE/CATHODE
8. ANODE/CATHODE
9. ANODE/CATHODE
10. NO CONNECTION
11. ANODE/CATHODE
12. ANODE/CATHODE
13. NO CONNECTION
14. COMMON ANODE
PIN 1. NO CONNECTION
2. ANODE
3. ANODE
4. NO CONNECTION
5. ANODE
6. NO CONNECTION
7. ANODE
8. ANODE
9. ANODE
10. NO CONNECTION
11. ANODE
12. ANODE
13. NO CONNECTION
14. COMMON CATHODE
3. CATHODE
4. NO CONNECTION
5. CATHODE
6. NO CONNECTION
7. CATHODE
8. CATHODE
9. CATHODE
10. NO CONNECTION
11. CATHODE
12. CATHODE
13. NO CONNECTION
14. COMMON ANODE
STYLE 5:
STYLE 6:
STYLE 7:
STYLE 8:
PIN 1. COMMON CATHODE
2. ANODE/CATHODE
3. ANODE/CATHODE
4. ANODE/CATHODE
5. ANODE/CATHODE
6. NO CONNECTION
7. COMMON ANODE
8. COMMON CATHODE
9. ANODE/CATHODE
10. ANODE/CATHODE
11. ANODE/CATHODE
12. ANODE/CATHODE
13. NO CONNECTION
14. COMMON ANODE
PIN 1. CATHODE
2. CATHODE
3. CATHODE
4. CATHODE
5. CATHODE
6. CATHODE
7. CATHODE
8. ANODE
PIN 1. ANODE/CATHODE
2. COMMON ANODE
3. COMMON CATHODE
4. ANODE/CATHODE
5. ANODE/CATHODE
6. ANODE/CATHODE
7. ANODE/CATHODE
8. ANODE/CATHODE
9. ANODE/CATHODE
10. ANODE/CATHODE
11. COMMON CATHODE
12. COMMON ANODE
13. ANODE/CATHODE
14. ANODE/CATHODE
PIN 1. COMMON CATHODE
2. ANODE/CATHODE
3. ANODE/CATHODE
4. NO CONNECTION
5. ANODE/CATHODE
6. ANODE/CATHODE
7. COMMON ANODE
8. COMMON ANODE
9. ANODE/CATHODE
10. ANODE/CATHODE
11. NO CONNECTION
12. ANODE/CATHODE
13. ANODE/CATHODE
14. COMMON CATHODE
9. ANODE
10. ANODE
11. ANODE
12. ANODE
13. ANODE
14. ANODE
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DOCUMENT NUMBER:
DESCRIPTION:
98ASB42565B
SOIC−14 NB
PAGE 2 OF 2
onsemi and
are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves
the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation
special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
TSSOP−14 WB
CASE 948G
ISSUE C
14
DATE 17 FEB 2016
1
SCALE 2:1
NOTES:
14X K REF
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
M
S
S
V
0.10 (0.004)
T U
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL
IN EXCESS OF THE K DIMENSION AT
MAXIMUM MATERIAL CONDITION.
S
0.15 (0.006) T U
N
0.25 (0.010)
14
8
2X L/2
M
B
L
N
−U−
PIN 1
IDENT.
F
7
1
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
DETAIL E
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
S
K
0.15 (0.006) T U
A
−V−
MILLIMETERS
DIM MIN MAX
INCHES
MIN MAX
K1
A
B
C
D
F
G
H
J
4.90
4.30
−−−
0.05
0.50
5.10 0.193 0.200
4.50 0.169 0.177
J J1
1.20
−−− 0.047
0.15 0.002 0.006
0.75 0.020 0.030
SECTION N−N
0.65 BSC
0.026 BSC
0.60 0.020 0.024
0.20 0.004 0.008
0.16 0.004 0.006
0.30 0.007 0.012
0.25 0.007 0.010
0.50
0.09
0.09
0.19
J1
K
−W−
C
K1 0.19
L
M
6.40 BSC
0.252 BSC
0.10 (0.004)
0
8
0
8
_
_
_
_
SEATING
PLANE
−T−
H
G
DETAIL E
D
GENERIC
MARKING DIAGRAM*
14
SOLDERING FOOTPRINT
XXXX
XXXX
ALYWG
G
7.06
1
1
A
L
= Assembly Location
= Wafer Lot
Y
W
G
= Year
= Work Week
= Pb−Free Package
0.65
PITCH
(Note: Microdot may be in either location)
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
01.34X6
14X
1.26
DIMENSIONS: MILLIMETERS
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DOCUMENT NUMBER:
DESCRIPTION:
98ASH70246A
TSSOP−14 WB
PAGE 1 OF 1
onsemi and
are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves
the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation
special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
ADDITIONAL INFORMATION
TECHNICAL PUBLICATIONS:
Technical Library: www.onsemi.com/design/resources/technical−documentation
onsemi Website: www.onsemi.com
ONLINE SUPPORT: www.onsemi.com/support
For additional information, please contact your local Sales Representative at
www.onsemi.com/support/sales
相关型号:
MM74HC02M_NL
NOR Gate, HC/UH Series, 4-Func, 2-Input, CMOS, PDSO14, 0.150 INCH, MS-012, SOIC-14
FAIRCHILD
MM74HC02N
NOR Gate, HC/UH Series, 4-Func, 2-Input, CMOS, PDIP14, 0.300 INCH, PLASTIC, MS-001, DIP-14
ROCHESTER
MM74HC02SJ
NOR Gate, HC/UH Series, 4-Func, 2-Input, CMOS, PDSO14, 5.30 MM, LEAD FREE, EIAJ TYPE2, SOP-14
ROCHESTER
MM74HC02SJX
NOR Gate, HC/UH Series, 4-Func, 2-Input, CMOS, PDSO14, 5.30 MM, LEAD FREE, EIAJ TYPE2, SOP-14
ROCHESTER
©2020 ICPDF网 联系我们和版权申明