LP2951CD [ONSEMI]
Micropower Voltage Regulators; 微功率稳压器型号: | LP2951CD |
厂家: | ONSEMI |
描述: | Micropower Voltage Regulators |
文件: | 总16页 (文件大小:291K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
The LP2950 and LP2951 are micropower voltage regulators that are
specifically designed to maintain proper regulation with an extremely
low input–to–output voltage differential. These devices feature a very
low quiescent bias current of 75 µA and are capable of supplying
output currents in excess of 100 mA. Internal current and thermal
limiting protection is provided.
http://onsemi.com
The LP2951 has three additional features. The first is the Error
Output that can be used to signal external circuitry of an out of
regulation condition, or as a microprocessor power–on reset. The
second feature allows the output voltage to be preset to 5.0 V, 3.3 V or
3.0 V output (depending on the version) or programmed from 1.25 V
to 29 V. It consists of a pinned out resistor divider along with direct
access to the Error Amplifier feedback input. The third feature is a
Shutdown input that allows a logic level signal to turn–off or turn–on
the regulator output.
TO–92
Z SUFFIX
CASE 29
Pin: 1. Output
2. Ground
3. Input
1
2
3
DPAK
DT SUFFIX
CASE 369A
1
3
Due to the low input–to–output voltage differential and bias current
specifications, these devices are ideally suited for battery powered
computer, consumer, and industrial equipment where an extension of
useful battery life is desirable. The LP2950 is available in the three
pin case 29 and DPAK packages, and the LP2951 is available in the
eight pin dual–in–line, SO–8 and Micro–8 surface mount packages.
The ‘A’ suffix devices feature an initial output voltage tolerance
±0.5%.
PIN CONNECTIONS
Pin: 1. Input
2. Ground
3. Output
1
2
3
(Top View)
Heatsink surface (shown as terminal 4 in
case outline drawing) is connected to Pin 2.
LP2950 and LP2951 Features:
• Low Quiescent Bias Current of 75 µA
SO–8
D SUFFIX
CASE 751
• Low Input–to–Output Voltage Differential of 50 mV at 100 µA and
380 mV at 100 mA
8
1
• 5.0 V, 3.3 V or 3.0 V ±0.5% Allows Use as a Regulator or Reference
• Extremely Tight Line and Load Regulation
• Requires Only a 1.0 µF Output Capacitor for Stability
• Internal Current and Thermal Limiting
LP2951 Additional Features:
N SUFFIX
CASE 626
8
1
• Error Output Signals an Out of Regulation Condition
• Output Programmable from 1.25 V to 29 V
Micro–8
DM SUFFIX
CASE 846A
8
• Logic Level Shutdown Input
1
(See Following Page for Device Information.)
PIN CONNECTIONS
1
2
3
4
8
7
6
5
Output
Sense
Input
Feedback
Shutdown
Gnd
V Tap
O
Error Output
(Top View)
ORDERING INFORMATION
Seedetailedorderingandshippinginformationinthepackage
dimensions section on page 13 of this data sheet.
Semiconductor Components Industries, LLC, 1999
1
Publication Order Number:
October, 1999 – Rev. 5
LP2950/D
LP2950
DEVICE INFORMATION
Output Voltage
Operating Junction
Temperature Range
Package
TO–92
3.0V
3.3V
5.0V
Adjustable
LP2950CZ–3.0
LP2950ACZ–3.0
LP2950CZ–3.3
LP2950ACZ–3.3
LP2950CZ–5.0
LP2950ACZ–5.0
Not
Available
T
J
T
J
T
J
T
J
T
J
= –40° to +125°C
= –40° to +125°C
= –40° to +125°C
= –40° to +125°C
= –40° to +125°C
Suffix Z
DPAK
Suffix DT
LP2950CDT–3.0
LP2950ACDT–3.0
LP2950CDT–3.3
LP2950ACDT–3.3
LP2950CDT–5.0
LP2950ACDT–5.0
Not
Available
SO–8
Suffix D
LP2951CD–3.0
LP2951ACD–3.0
LP2951CD–3.3
LP2951ACD–3.3
LP2951CD
LP2951ACD
LP2951CD
LP2951ACD
Micro–8
Suffix DM
LP2951CDM–3.0
LP2951ACDM–3.0
LP2951CDM–3.3
LP2951ACDM–3.3
LP2951CDM
LP2951ACDM
LP2951CDM
LP2951ACDM
DIP–8
Suffix N
LP2951CN–3.0
LP2951ACN–3.0
LP2951CN–3.3
LP2951ACN–3.3
LP2951CN
LP2951ACN
LP2951CN
LP2951ACN
LP2950Cx–xx / LP2951Cxx–xx
LP2950ACx–xx / LP2951ACxx–xx
1% Output Voltage Precision at T = 25°C
J
0.5% Output Voltage Precision at T = 25°C
J
Representative Block Diagrams
Input
Output
1
5.0 V/100 mA
3
1.0 µF
Battery or
Unregulated DC
182 k
60 k
Error Amplifier
1.23 V
Reference
LP2950CZ–5.0
Gnd
2
5.0 V/100 mA
Input
8
Output
Sense
182 k
2
1
Battery or
Unregulated DC
1.0 µF
V Tap
O
6
60 k
330 k
7
Feedback
Error
Amplifier
Shutdown
From
CMOS/TTL
3
60 k
50 k
75 mV/
60 mV
Error
Output
To CMOS/TTL
5
Error Detection
Comparator
1.23 V
Reference
LP2951CD or CN
Gnd
4
This device contains 34 active transistors.
http://onsemi.com
2
LP2950
MAXIMUM RATINGS (T = 25°C, unless otherwise noted.)
A
Rating
Symbol
Value
Unit
Input Voltage
V
CC
30
Vdc
Power Dissipation and Thermal Characteristics
Maximum Power Dissipation
P
D
Internally Limited
W
Case 751(SO–8) D Suffix
Thermal Resistance, Junction–to–Ambient
Thermal Resistance, Junction–to–Case
Case 369A (DPAK) DT Suffix [Note 1]
Thermal Resistance, Junction–to–Ambient
Thermal Resistance, Junction–to–Case
Case 29 (TO–226AA/TO–92) Z Suffix
Thermal Resistance, Junction–to–Ambient
Thermal Resistance, Junction–to–Case
Case 626 N Suffix
R
R
180
45
°C/W
°C/W
θJA
θJC
R
θJA
R
θJC
92
6.0
°C/W
°C/W
R
θJA
R
θJC
160
83
°C/W
°C/W
Thermal Resistance, Junction–to–Ambient
Case 846A (Micro–8) DM Suffix
Thermal Resistance, Junction–to–Ambient
R
105
°C/W
θJA
θJA
R
240
°C/W
Feedback Input Voltage
V
fb
–1.5 to +30
Vdc
Shutdown Input Voltage
V
–0.3 to +30
–0.3 to +30
–40 to +125
–65 to +150
Vdc
Vdc
°C
sd
Error Comparator Output Voltage
Operating Junction Temperature
Storage Temperature Range
V
err
T
J
T
stg
°C
NOTE: 1. The Junction–to–Ambient Thermal Resistance is determined by PC board copper area per Figure 26.
2. ESD data available upon request.
ELECTRICAL CHARACTERISTICS (V = V + 1.0 V, I = 100 µA, C = 1.0 µF, T = 25°C [Note 1], unless
in
O
O
O
J
otherwise noted.)
Characteristic
Output Voltage, 5.0 V Versions
= 6.0 V, I = 100 µA, T = 25°C
Symbol
Min
Typ
Max
Unit
V
O
V
O
V
O
V
V
in
O
J
LP2950C–5.0/LP2951C
LP2950AC–5.0/LP2951AC
4.950
4.975
5.000
5.000
5.050
5.025
T
J
= –40 to +125°C
LP2950C–5.0/LP2951C
LP2950AC–5.0/LP2951AC
4.900
4.940
–
–
5.100
5.060
V
in
= 6.0 to 30 V, I = 100 µA to 100 mA, T = –40 to +125°C
O
J
LP2950C–5.0/LP2951C
LP2950AC–5.0/LP2951AC
4.880
4.925
–
–
5.120
5.075
Output Voltage, 3.3 V Versions
= 4.3 V, I = 100 µA, T = 25°C
V
V
in
O
J
LP2950C–3.3/LP2951C–3.3
LP2950AC–3.3/LP2951AC–3.3
3.267
3.284
3.300
3.300
3.333
3.317
T
J
= –40 to +125°C
LP2950C–3.3/LP2951C–3.3
LP2950AC–3.3/LP2951AC–3.3
3.234
3.260
–
–
3.366
3.340
V
in
= 4.3 to 30 V, I = 100 µA to 100 mA, T = –40 to +125°C
O
J
LP2950C–3.3/LP2951C–3.3
LP2950AC–3.3/LP2951AC–3.3
3.221
3.254
–
–
3.379
3.346
Output Voltage, 3.0 V Versions
= 4.0 V, I = 100 µA, T = 25°C
V
V
in
O
J
LP2950C–3.0/LP2951C–3.0
LP2950AC–3.0/LP2951AC–3.0
2.970
2.985
3.000
3.000
3.030
3.015
T
J
= –40 to +125°C
LP2950C–3.0/LP2951C–3.0
LP2950AC–3.0/LP2951AC–3.0
2.940
2.964
–
–
3.060
3.036
V
in
= 4.0 to 30 V, I = 100 µA to 100 mA, T = –40 to +125°C
O
J
LP2950C–3.0/LP2951C–3.0
LP2950AC–3.0/LP2951AC–3.0
2.928
2.958
–
–
3.072
3.042
http://onsemi.com
3
LP2950
ELECTRICAL CHARACTERISTICS (continued) (V = V + 1.0 V, I = 100 µA, C = 1.0 µF, T = 25°C [Note 1], unless
in
O
O
O
J
otherwise noted.)
Characteristic
+1.0 V to 30 V) [Note 2]
Symbol
Min
Typ
Max
Unit
Line Regulation (V = V
in
Reg
%
O(nom)
line
LP2950C–XX/LP2951C/LP2951C–XX
LP2950AC–XX/LP2951AC/LP2951AC–XX
–
–
0.08
0.04
0.20
0.10
Load Regulation (I = 100 µA to 100 mA)
Reg
%
O
load
LP2950C–XX/LP2951C/LP2951C–XX
LP2950AC–XX/LP2951AC/LP2951AC–XX
–
–
0.13
0.05
0.20
0.10
Dropout Voltage
V – V
I
mV
O
I
O
I
O
= 100 µA
= 100 mA
–
–
30
350
80
450
Supply Bias Current
I
CC
I
O
I
O
= 100 µA
= 100 mA
–
–
93
4.0
120
12
µA
mA
Dropout Supply Bias Current (V = V
in
O
– 0.5 V,
I
–
110
170
µA
O(nom)
CCdropout
I
= 100 µA) [Note 2]
Current Limit (V Shorted to Ground)
O
I
–
–
220
300
mA
%/W
Limit
Reg
Thermal Regulation
0.05
0.20
thermal
Output Noise Voltage (10 Hz to 100 kHz) [Note 3]
V
n
µVrms
C
C
= 1.0 µF
= 100 µF
–
–
126
56
–
–
L
L
LP2951A/LP2951AC ONLY
Reference Voltage (T = 25°C)
LP2951C/LP2951C–XX
LP2951AC/LP2951AC–XX
V
V
V
V
J
ref
1.210
1.220
1.235
1.235
1.260
1.250
Reference Voltage (T = –40 to +125°C)
V
ref
J
LP2951C/LP2951C–XX
LP2951AC/LP2951AC–XX
1.200
1.200
–
–
1.270
1.260
Reference Voltage (T = –40 to +125°C)
V
ref
J
I
O
= 100 µA to 100 mA, V = 23 to 30 V
in
LP2951C/LP2951C–XX
LP2951AC/LP2951AC–XX
1.185
1.190
–
–
1.285
1.270
Feedback Pin Bias Current
ERROR COMPARATOR
Output Leakage Current (V
I
–
15
40
nA
FB
= 30 V)
I
–
–
0.01
150
45
1.0
250
–
µA
mV
mV
mV
mV
OH
lkg
Output Low Voltage (V = 4.5 V, I
in
= 400 µA)
V
V
OL
OL
Upper Threshold Voltage (V = 6.0 V)
in
40
–
thu
Lower Threshold Voltage (V = 6.0 V)
in
V
60
95
–
thl
hy
Hysteresis (V = 6.0 V)
in
V
–
15
SHUTDOWN INPUT
Input Logic Voltage
V
shtdn
V
Logic “0” (Regulator “On”)
Logic “1” (Regulator “Off”)
0
2.0
–
–
0.7
30
Shutdown Pin Input Current
I
µA
µA
shtdn
V
shtdn
V
shtdn
= 2.4 V
= 30 V
–
–
35
450
50
600
Regulator Output Current in Shutdown Mode
(V = 30 V, V = 2.0 V, V = 0, Pin 6 Connected to Pin 7)
I
off
–
3.0
10
in shtdn
O
NOTES: 1. Low duty pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
2. V is the part number voltage option.
O(nom)
3. Noise tests on the LP2951 are made with a 0.01 µF capacitor connected across Pins 7 and 1.
http://onsemi.com
4
LP2950
DEFINITIONS
Dropout Voltage – The input/output voltage differential
Output Noise Voltage – The rms ac voltage at the output,
with constant load and no input ripple, measured over a
specified frequency range.
at which the regulator output no longer maintains regulation
against further reductions in input voltage. Measured when
the output drops 100 mV below its nominal value (which is
measured at 1.0 V differential), dropout voltage is affected
by junction temperature, load current and minimum input
supply requirements.
Line Regulation – The change in output voltage for a
change in input voltage. The measurement is made under
conditions of low dissipation or by using pulse techniques
such that average chip temperature is not significantly
affected.
Load Regulation – The change in output voltage for a
change in load current at constant chip temperature.
Maximum Power Dissipation – The maximum total
device dissipation for which the regulator will operate
within specifications.
Leakage Current – Current drawn through a bipolar
transistor collector–base junction, under a specified
collector voltage, when the transistor is “off”.
Upper Threshold Voltage – Voltage applied to the
comparator input terminal, below the reference voltage
which is applied to the other comparator input terminal,
which causes the comparator output to change state from a
logic “0” to “1”.
Lower Threshold Voltage – Voltage applied to the
comparator input terminal, below the reference voltage
which is applied to the other comparator input terminal,
which causes the comparator output to change state from a
logic “1” to “0”.
Hysteresis – The difference between Lower Threshold
voltage and Upper Threshold voltage.
Bias Current – Current which is used to operate the
regulator chip and is not delivered to the load.
Figure 1. Quiescent Current
Figure 2. Dropout Characteristics
10
6.0
LP2951C
T = 25°C
A
5.0
4.0
3.0
2.0
1.0
0
R = 50 k
L
1.0
0.1
R = 50 Ω
L
0.01
0.1
1.0
10
100
0
1.0
2.0
3.0
4.0
5.0
6.0
I , LOAD CURRENT (mA)
L
V , INPUT VOLTAGE (V)
in
Figure 3. Input Current
Figure 4. Output Voltage versus Temperature
250
5.00
4.99
4.98
4.97
4.96
4.95
200
150
100
50
0.1 mA Load Current
No Load
LP2951C
0
0
5.0
10
15
20
25
– 50
0
50
100
150
200
V , INPUT VOLTAGE (V)
in
T , AMBIENT TEMPERATURE (°C)
A
http://onsemi.com
5
LP2950
Figure 5. Dropout Voltage versus
Output Current
Figure 6. Dropout Voltage versus Temperature
400
350
550
500
450
400
350
300
55
50
45
40
35
30
T = 25°C
A
300
250
200
150
100
50
R = 50
L
R = 50 k
L
0
0.1
1.0
10
100
– 50
0
50
T, TEMPERATURE (°C)
100
150
I , OUTPUT CURRENT (mA)
O
Figure 7. Error Comparator Output
Figure 8. Line Transient Response
5.0
4.0
3.0
2.0
1.0
0
4.0
8.0
7.5
7.0
6.5
6.0
5.5
V
in
LP2951C
R = 330 k
T = 25°C
A
L
2.0
V Decreasing
in
0
V
out
V Increasing
in
– 2.0
– 4.0
– 6.0
T = 25°C
C = 1.0 µF
I = 1.0 mA
V = 5.0 V
A
L
L
O
4.70
4.74
4.78
4.82
4.86
4.90
0
100
200
300
400
500
600
700
800
V , INPUT VOLTAGE (V)
in
t, TIME (µs)
Figure 9. LP2951 Enable Transient
Figure 10. Load Transient Response
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0
200
150
100
50
C = 1.0 µF
L
C = 1.0 µF
L
400
200
0
V
= 5.0 V
out
T = 25°C
A
V
out
C = 10 µF
L
T = 25°C
A
I = 10 mA
L
– 200
– 400
V = 8.0 V
in
out
I
Load
V
= 5.0 V
0
Shutdown Input
–1.0
–100
– 50
0
100
200
300
400
0
50
100
150
200
250
300
350
400
t, TIME (µs)
t, TIME (ms)
http://onsemi.com
6
LP2950
Figure 11. Ripple Rejection
Figure 12. Output Noise
80
60
40
4.0
3.0
2.0
1.0
0
I = 100 mA
L
T = 25°C
A
C = 1.0 µF
V = 5.0 V
L
O
LP2951C
I = 0.1 mA
L
T = 25°C
A
C = 100 µF
L
20
0
C = 1.0 µF
L
V = 6.0 V
in
out
V
= 5.0 V
1.0
1.0 k
f, FREQUENCY (Hz)
100
1.0 k
f, FREQUENCY (Hz)
10
100
10 k
100 k
10 k
100 k
Figure 13. Shutdown Threshold Voltage
versus Temperature
Figure 14. Maximum Rated
Output Current
1.8
1.6
100
4.0
T = 25°C
A
80
60
40
20
0
2.0
T = 75°C
A
0
1.4
1.2
Output “Off”
Output “On”
– 2.0
– 4.0
– 6.0
1.0
0.8
LP2951CN
5.0
– 40 – 20
0
20
40
60
80 100 120 140 160
0
10
15
20
25
30
35
40
t, TEMPERATURE (°C)
V , INPUT VOLTAGE (V)
in
http://onsemi.com
7
LP2950
APPLICATIONS INFORMATION
Introduction
The LP2950/LP2951 regulators are designed with
internalcurrentlimitingandthermalshutdownmakingthem
user–friendly. Typical application circuits for the LP2950
and LP2951 are shown in Figures 17 through 25.
These regulators are not internally compensated and thus
require a 1.0 µF (or greater) capacitance between the
LP2950/LP2951 output terminal and ground for stability.
Most types of aluminum, tantalum or multilayer ceramic
will perform adequately. Solid tantalums or appropriate
multilayer ceramic capacitors are recommended for
operation below 25°C.
At lower values of output current, less output capacitance
is required for output stability. The capacitor can be reduced
to0.33µFforcurrentslessthan10mA, or0.1µFforcurrents
below1.0 mA. Using the 8–pin versions at voltages less than
5.0 V operates the error amplifier at lower values of gain, so
that more output capacitance is needed for stability. For the
worst case operating condition of a 100 mA load at 1.23 V
output (Output Pin 1 connected to the feedback Pin 7) a
minimum capacitance of 3.3 µF is recommended.
The LP2950 will remain stable and in regulation when
operated with no output load. When setting the output
voltage of the LP2951 with external resistors, the resistance
values should be chosen to draw a minimum of 1.0 µA.
to the LP2951 is ramped up and down. The ERROR signal
becomes valid (low) at about 1.3 V input. It goes high when
the input reaches about 5.0 V (V exceeds about 4.75 V).
out
Since the LP2951’s dropout voltage is dependent upon the
load current (refer to the curve in the Typical Performance
Characteristics), the input voltage trip point will vary with
load current. The output voltage trip point does not vary
with load.
The error comparator output is an open collector which
requires an external pull–up resistor. This resistor may be
returned to the output or some other voltage within the
system. The resistance value should be chosen to be
consistent with the 400 µA sink capability of the error
comparator. A value between 100 k and 1.0 MΩ is
suggested. No pull–up resistance is required if this output is
unused.
When operated in the shutdown mode, the error
comparator output will go high if it has been pulled up to an
external supply. To avoid this invalid response, the error
comparator output should be pulled up to V
Figure 15).
(see
out
Figure 15. ERROR Output Timing
5.0 V
A
bypass capacitor is recommended across the
4.70 V
4.75 V
Output
Voltage
LP2950/LP2951 input to ground if more than 4 inches of
wire connects the input to either a battery or power supply
filter capacitor.
Input capacitance at the LP2951 Feedback Pin 7 can
create a pole, causing instability if high value external
resistors are used to set the output voltage. Adding a 100 pF
capacitor between the Output Pin 1 and the Feedback Pin 7
and increasing the output filter capacitor to at least 3.3 µF
will stabilize the feedback loop.
Pull–Up
to Ext
Not
Not
Valid
Valid
ERROR
Pull–Up
to V
out
4.75 V + V
dropout
4.70 V + V
dropout
Error Detection Comparator
Input
The comparator switches to a positive logic low whenever
the LP2951 output voltage falls more than approximately
5.0% out of regulation. This value is the comparator’s
designed–in offset voltage of 60 mV divided by the 1.235 V
internal reference. As shown in the representative block
diagram. This trip level remains 5.0% below normal
regardless of the value of regulated output voltage. For
example, the error flag trip level is 4.75 V for a normal 5.0
V regulated output, or 9.50 V for a 10 V output voltage.
Figure 1 is a timing diagram which shows the ERROR
signal and the regulated output voltage as the input voltage
1.3 V
Voltage
1.3 V
Programming the Output Voltage (LP2951)
The LP2951CX may be pin–strapped for 5.0 V using its
internal voltage divider by tying Pin 1 (output) to Pin 2
(sense) and Pin 7 (feedback) to Pin 6 (5.0 V tap).
Alternatively, it may be programmed for any output voltage
between its 1.235 reference voltage and its 30 V maximum
rating. An external pair of resistors is required, as shown in
Figure 16.
http://onsemi.com
8
LP2950
Figure 16. Adjustable Regulator
decreasesthenoisefrom430µVto160µVrmsfora100kHz
bandwidth at the 5.0 V output.
V
in
Noise can be reduced fourfold by a bypass capacitor
across R1, since it reduces the high frequency gain from 4
to unity. Pick
100 k
5
8
1
V
in
C
1
Error
Output
Bypass
2 R1 x 200 Hz
V
out
Error
V
out
or about 0.01 µF. When doing this, the output capacitor must
be increased to 3.3 µF to maintain stability. These changes
reduce the output noise from 430 µV to 126 µVrms for a
100 kHz bandwidth at 5.0 V output. With bypass
capacitor added, noise no longer scales with output voltage
so that improvements are more dramatic at higher output
voltages.
2
1.23 to 30 V
NC
NC
SNS
R1
Shutdown
Input
3
6
0.01 µF
SD
V T
O
3.3 µF
Gnd FB
4
7
R
2
Figure 17. 1.0 A Regulator with 1.2 V Dropout
Unregulated
The complete equation for the output voltage is:
Input
MTB23P06E
1.0 µF
(
)
V
1
R1 R2
I
R1
out
ref
FB
10 k
0.01 µF
whereV isthenominal1.235VreferencevoltageandI
ref FB
V
out
is the feedback pin bias current, nominally –20 nA. The
minimum recommended load current of 1.0 µA forces an
upper limit of 1.2 MΩ on the value of R2, if the regulator
5.0 V ±1.0%
0 to 1.0 A
8
V
in
1
2
5
3
Error
Output
V
Error
out
must work with no load. I will produce a 2% typical error
FB
in V which may be eliminated at room temperature by
out
SNS
LP2951CN
adjusting R1. For better accuracy, choosing R2 = 100 k
reduces this error to 0.17% while increasing the resistor
program current to 12 µA. Since the LP2951 typically draws
75 µA at no load with Pin 2 open circuited, the extra 12 µA
of current drawn is often a worthwhile tradeoff for
eliminating the need to set output voltage in test.
6
Shutdown
Input
SD
V T
O
220 µF
Gnd FB
4
7
0.002 µF
1.0 M
Output Noise
2.0 k
In many applications it is desirable to reduce the noise
present at the output. Reducing the regulator bandwidth by
increasing the size of the output capacitor is the only method
for reducing noise on the 3 lead LP2950. However,
increasing the capacitor from 1.0 µF to 220 µF only
http://onsemi.com
9
LP2950
TYPICAL APPLICATIONS
Figure 18. Lithium Ion Battery Cell Charger
Figure 19. Low Drift Current Sink
+V = 2.0 to 30 V
Unregulated Input
6.0 to 10 Vdc
I
L
I = 1.23/R
L
Load
8
V
1N4001
330 pF
4.2 V ± 0.025 V
in
1
2
5
Error
V
out
NC
8
0.1 µF
2.0 M
1.0%
NC
NC
SNS
LP2951CN
V
in
1
2
Error
Output
5
V
0.1 µF
Error
out
3
6
SD
V T
O
SNS
LP2951CN
806 k
1.0%
Lithium Ion
Rechargeable
Cell
Gnd FB
2.2 µF
Shutdown
Input
3
6
4
7
SD
V T
O
50 k
Gnd FB
4
7
Gnd
1.0 µF
R
Figure 20. Latch Off When Error Flag Occurs
Figure 21. 5.0 V Regulator with 2.5 V Sleep Function
+V
in
+V
in
CMOS
Gate
*Sleep
Input
8
V
in
470 k
470 k
470 k
8
V
in
47 k
Error
1
2
5
3
V
V
out
Error
out
V
out
2N3906
2N3906
1
2
5
V
out
Error
Output
NC
NC
SNS
LP2951CN
Reset
NC
NC
SNS
LP2951CN
200 k
100 k
6
R1
R2
SD V T
O
Shutdown
Input
3
6
3.3 µF
Normally
Closed
SD
V T
O
Gnd FB
1.0 µF
100 pF
4
7
Gnd FB
4
7
100 k
Error flag occurs when V is too low to
in
maintain V , or if V
out out
excessive load current.
is reduced by
http://onsemi.com
10
LP2950
Figure 22. Regulator with Early Warning and Auxiliary Output
+V
in
8
V
D2
in
1
2
Memory
V+
5
3
V
Error
out
D1
1.0 µF
20
SNS
LP2951CN
#1
3.6 V
NiCad
6
NC
SD
V T
O
Gnd FB
4
7
Early Warning
Reset
27 k
All diodes are 1N4148.
D3
Early Warning flag on low input voltage.
µP
2.7 M
Main output latches off at lower input
voltages.
D4
V
DD
Q1
2N3906
8
V
in
Battery backup on auxiliary output.
330 k
1
2
5
3
Operation: Regulator #1’s V
programmed one diode drop above 5.0 V.
is
out
V
Error
out
Main
Output
Its error flag becomes active when V < 5.7
V. When V drops below 5.3 V, the error
in
flag of regulator #2 becomes active and via
in
SNS
LP2951CN
#2
1.0 µF
Q1 latches the main output “off”. When V
6
in
SD
V T
O
again exceeds 5.7 V, regulator #1 is back in
regulation and the early warning signal
rises, unlatching regulator #2 via D3.
Gnd FB
4
7
Figure 23. 2.0 A Low Dropout Regulator
+V
in
Current Limit
Section
0.05
470
680
2N3906
1000 µF
2N3906
MJE2955
.33 µF
10 k
4.7 M
8
V
in
1
2
Error
Flag
5
3
V
Error
out
V
out
@ 2.0 A
NC 47
NC
SNS
LP2951CN
220
6
4.7 µF
Tant
SD
V T
O
100 µF
R1
Gnd FB
20 k
.01 µF
4
7
R2
0.033 µF
V
= 1.25V (1.0 + R1/R2)
out
For 5.0 V output, use internal resistors. Wire Pin 6 to 7,
and wire Pin 2 to +V
out
Bus.
http://onsemi.com
11
LP2950
Figure 24. Open Circuit Detector for 4.0 to 20 mA Current Loop
+5.0 V
4.7 k
Output*
1
2
5
4
20 mA
NC
8
V
in
1
4
5
3
V
Error
out
2
NC
NC
SNS
LP2951CN
* High for
I < 3.5 mA
L
6
NC
SD
V T
O
0.1 µF
1N4001
Gnd FB
4
7
1N457
1N457
1N457
360
Figure 25. Low Battery Disconnect
31.6 k
6.0 V Lead–Acid
Battery
100 k
2N3906
NC
8
V
in
1
2
5
3
V
Main V+
Error
out
1
MC34164P–5
2
SNS
LP2951CN
Memory V+
3
1.0 µF
6
20
SD
V T
O
NC
NiCad Backup
Battery
Gnd FB
4
7
NC
Figure 26. DPAK Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
100
90
80
70
60
50
40
2.4
P
for T = 50°C
A
D(max)
Free Air
Mounted
Vertically
2.0
1.6
1.2
0.8
0.4
0
2.0 oz. Copper
L
Minimum
Size Pad
L
R
θJA
0
5.0
10
15
20
25
30
L, LENGTH OF COPPER (mm)
http://onsemi.com
12
LP2950
ORDERING INFORMATION
Package
Part Number
LP2950CZ–3.0RA
Shipping
2000 units / Tape & Reel
TO–92
TO–92
TO–92
TO–92
TO–92
TO–92
DPAK
DPAK
DPAK
DPAK
DPAK
DPAK
DPAK
DPAK
DPAK
DPAK
DPAK
DPAK
LP2950ACZ–3.0RA
LP2950CZ–3.3RA
LP2950ACZ–3.3RA
LP2950CZ–5.0RA
LP2950ACZ–5.0RA
LP2950CDT–3.0
2000 units / Tape & Reel
2000 units / Tape & Reel
2000 units / Tape & Reel
2000 units / Tape & Reel
2000 units / Tape & Reel
75 units / Rail
LP2950CDT–3.0RK
LP2950ACDT–3.0
LP2950ACDT–3.0RK
LP2950CDT–3.3
2500 units / Tape & Reel
75 units / Rail
2500 units / Tape & Reel
75 units / Rail
LP2950CDT–3.3RK
LP2950ACDT–3.3
LP2950ACDT–3.3RK
LP2950CDT–5.0
2500 units / Tape & Reel
75 units / Rail
2500 units / Tape & Reel
75 units / Rail
LP2950CDT–5.0RK
LP2950ACDT–5.0
LP2950ACDT–5.0RK
2500 units / Tape & Reel
75 units / Rail
2500 units / Tape & Reel
LP2951CD–3.0
LP2951CD–3.0R2
LP2951ACD–3.0
LP2951ACD–3.0R2
LP2951CD–3.3
LP2951CD–3.3R2
LP2951ACD–3.3
LP2951ACD–3.3R2
LP2951CD
SO–8
SO–8
98 units / Rail
2500 units / Tape & Reel
98 units / Rail
SO–8
SO–8
2500 units / Tape & Reel
98 units / Rail
SO–8
SO–8
2500 units / Tape & Reel
98 units / Rail
SO–8
SO–8
2500 units / Tape & Reel
98 units / Rail
SO–8
LP2951CDR2
SO–8
2500 units / Tape & Reel
98 units / Rail
LP2951ACD
SO–8
LP2951ACDR2
LP2951CDM–3.0R2
LP2951ACDM–3.0R2
LP2951CDM–3.3R2
LP2951ACDM–3.3R2
LP2951CDMR2
LP2951ACDMR2
LP2951CN–3.0
LP2951ACN–3.0
LP2951CN–3.3
LP2951ACN–3.3
LP2951CN
SO–8
2500 units / Tape & Reel
2500 units / Tape & Reel
2500 units / Tape & Reel
2500 units / Tape & Reel
2500 units / Tape & Reel
2500 units / Tape & Reel
2500 units / Tape & Reel
50 units / Rail
Micro–8
Micro–8
Micro–8
Micro–8
Micro–8
Micro–8
DIP–8
DIP–8
DIP–8
DIP–8
DIP–8
DIP–8
50 units / Rail
50 units / Rail
50 units / Rail
50 units / Rail
LP2951ACN
50 units / Rail
http://onsemi.com
13
LP2950
PACKAGE DIMENSIONS
Z SUFFIX
(TO–226AA/TO–92)
PLASTIC PACKAGE
CASE 29–04
ISSUE AD
NOTES:
A
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
B
2. CONTROLLING DIMENSION: INCH.
3. CONTOUR OF PACKAGE BEYOND DIMENSION R
IS UNCONTROLLED.
R
4. DIMENSION F APPLIES BETWEEN P AND L.
DIMENSION D AND J APPLY BETWEEN L AND K
MINIMUM. LEAD DIMENSION IS UNCONTROLLED
IN P AND BEYOND DIMENSION K MINIMUM.
P
L
F
SEATING
PLANE
K
INCHES
DIM MIN MAX
MILLIMETERS
MIN
4.45
4.32
3.18
0.41
0.41
1.15
2.42
0.39
MAX
5.20
5.33
4.19
0.55
0.48
1.39
2.66
0.50
–––
A
B
C
D
F
G
H
J
K
L
N
P
0.175
0.170
0.125
0.016
0.016
0.045
0.095
0.015
0.500
0.250
0.080
–––
0.205
0.210
0.165
0.022
0.019
0.055
0.105
0.020
D
X X
G
J
H
V
C
––– 12.70
–––
0.105
0.100
–––
6.35
2.04
–––
2.93
3.43
–––
SECTION X–X
2.66
2.54
–––
1
N
R
V
0.115
0.135
N
–––
–––
DT SUFFIX
(DPAK)
PLASTIC PACKAGE
CASE 369A–13
ISSUE Y
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
SEATING
PLANE
–T–
2. CONTROLLING DIMENSION: INCH.
C
B
R
INCHES
DIM MIN MAX
MILLIMETERS
E
V
MIN
5.97
6.35
2.19
0.69
0.84
0.94
MAX
6.35
6.73
2.38
0.88
1.01
1.19
A
B
C
D
E
F
0.235
0.250
0.086
0.027
0.033
0.037
0.250
0.265
0.094
0.035
0.040
0.047
4
2
Z
A
K
S
1
3
G
H
J
K
L
R
S
U
V
Z
0.180 BSC
4.58 BSC
U
0.034
0.018
0.102
0.040
0.023
0.114
0.87
0.46
2.60
1.01
0.58
2.89
0.090 BSC
2.29 BSC
F
J
0.175
0.020
0.020
0.030
0.138
0.215
0.050
–––
0.050
–––
4.45
0.51
0.51
0.77
3.51
5.46
1.27
–––
1.27
–––
L
H
D 2 PL
M
G
0.13 (0.005)
T
http://onsemi.com
14
LP2950
PACKAGE DIMENSIONS
N SUFFIX
PLASTIC PACKAGE
CASE 626–05
ISSUE K
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
8
5
4
–B–
1
MILLIMETERS
DIM MIN MAX
INCHES
MIN MAX
10.16 0.370 0.400
6.60 0.240 0.260
4.45 0.155 0.175
0.51 0.015 0.020
1.78 0.040 0.070
9.40
6.10
3.94
0.38
1.02
A
B
C
D
F
G
H
J
F
NOTE 2
–A–
L
2.54 BSC
0.100 BSC
1.27 0.030 0.050
0.30 0.008 0.012
0.76
0.20
2.92
3.43
0.115 0.135
K
L
C
7.62 BSC
0.300 BSC
–
–
0.76
10°
1.01
10°
0.040
M
N
J
0.030
–T–
SEATING
PLANE
N
M
D
K
G
H
M
M
M
0.13 (0.005)
A
B
T
D SUFFIX
(SO–8)
PLASTIC PACKAGE
CASE 751–05
ISSUE R
NOTES:
D
A
E
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. DIMENSIONS ARE IN MILLIMETERS.
3. DIMENSION D AND E DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE B DIMENSION AT MAXIMUM MATERIAL
CONDITION.
C
8
5
M
M
0.25
B
H
1
4
h X 45
MILLIMETERS
B
C
e
DIM MIN
MAX
1.75
0.25
0.49
0.25
5.00
4.00
A
A1
B
C
D
E
1.35
0.10
0.35
0.18
4.80
3.80
A
SEATING
PLANE
L
e
1.27 BSC
0.10
H
h
L
5.80
0.25
0.40
0
6.20
0.50
1.25
7
A1
B
M
S
S
0.25
C B
A
http://onsemi.com
15
LP2950
PACKAGE DIMENSIONS
DM SUFFIX
(Micro–8)
PLASTIC PACKAGE
CASE 846A–02
ISSUE C
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
–A–
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010)
PER SIDE.
–B–
K
MILLIMETERS
INCHES
PIN 1 ID
G
DIM MIN
MAX
3.10
3.10
1.10
MIN
0.114
0.114
MAX
0.122
0.122
D 8 PL
A
B
C
D
G
H
J
2.90
2.90
–––
M
S
S
0.08 (0.003)
T B
A
––– 0.043
0.25
0.40 0.010 0.016
0.65 BSC
0.026 BSC
0.15 0.002 0.006
0.23 0.005 0.009
5.05 0.187 0.199
0.70 0.016 0.028
0.05
0.13
4.75
0.40
SEATING
PLANE
–T–
K
L
0.038 (0.0015)
C
L
J
H
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
withoutfurthernoticetoanyproductsherein. SCILLCmakesnowarranty,representationorguaranteeregardingthesuitabilityofitsproductsforanyparticular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLCproductsarenotdesigned, intended, orauthorizedforuseascomponentsinsystemsintendedforsurgicalimplantintothebody, orotherapplications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorneyfees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
USA/EUROPE Literature Fulfillment:
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
Email: ONlit–asia@hibbertco.com
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: ONlit@hibbertco.com
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–8549
Phone: 81–3–5487–8345
Fax Response Line*: 303–675–2167
800–344–3810 Toll Free USA/Canada
*To receive a Fax of our publications
Email: r14153@onsemi.com
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local Sales Representative.
N. America Technical Support: 800–282–9855 Toll Free USA/Canada
LP2950/D
相关型号:
LP2951CD-3.0G
LDO Regulator, 100 mA, 30V, Micropower, with Shutdown Vout: 3.0 V; 1.0%, SOIC-8 Narrow Body, 98-TUBE
ONSEMI
LP2951CD-3.0R2
FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, 0.45V DROPOUT, PDSO8, PLASTIC, SO-8
MOTOROLA
LP2951CD-3.0R2
FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, 0.45V DROPOUT, PDSO8, PLASTIC, SOIC-8
ONSEMI
©2020 ICPDF网 联系我们和版权申明