LC89058W-E [ONSEMI]
数字音频接口接收器;
ONSEMI 
Ordering number : ENA1056A
LC89058W-E
CMOS IC
http://onsemi.com
Digital Audio Interface Receiver
1. Overview
The LC89058W-E is a digital audio interface receiver IC that demodulates signals according to a data transfer format
between digital audio devices via the IEC60958/61937 and JEITA CPR-1205. It supports demodulation sampling
frequencies of up to 192kHz. The LC89058W-E can easily replace the existing LC89057W-VF4A-E.
The LC89058W-E incorporates a number of features for its low cost and is optimal for receiving digital data for AV
amplifiers and receivers.
2. Features
2.1 Clock
• Built-in PLL false lock prevention circuit to provide accurate lock.
• Includes built-in oscillation amplifier and frequency divider for quartz resonator.
• Output clock: 512fs, 256fs, 128fs, 64fs, 32fs, 16fs, 2fs, fs, 1/2fs, and 1/4fs.
• Possible to set the oscillation amplifier (external input) clock output regardless of the PLL status.
• Generates transition period signal for switching between the PLL clock and oscillation amplifier (external input)
clock.
• Allows the user to set the PLL clock output frequency for each sampling frequency band of input data.
2.2 Data
• Can receive S/PDIF and serial data at sampling frequencies of 32kHz to 192kHz.
• Equipped with a total of 7 digital data input pins: 1 input pin with an amplifier and 6 input pins with 5V tolerable
TTL level signal.
• Can generate data to be demodulated and through output data separately from a maximum of 7 kinds of S/PDIFs.
• Equipped an S/PDIF input data detection function. Possible to monitor the data input status of 32kHz to 192kHz
with
microcontroller.
Continued on next page.
Semiconductor Components Industries, LLC, 2013
May, 2013
41509HKIM VL-2643/N0508HKIM VL-2625 No.A1056-1/64
LC89058W-E
Continued from preceding page.
• Equipped with a serial data input pin. Possible to switch with demodulation output automatically according to the
state of the PLL circuit.
• The fs reception range of S/PDIF interface can be limited. LC89058W-E can be set to a no-signal input state if the
reception range is exceeded.
• Supports I2S data output that facilitates interfacing with DSP.
2.3 Other
• Supports Multi-channel transfer and reception, using master/slave function.
• Equipped with a 4bits general-purpose I/O pins. They can be used for interface with peripheral ICs.
• The general-purpose I/O pins can also serve as selector inputs. Possible to switch with HDMI and XM-radio signals.
• Generates a DTS-CD/LD detection flag on detection of a DTS synchronization signal.
• Outputs interrupt signal for microcontroller (interrupt source can be selected).
• Calculates sampling frequency of input signal and outputs it from the terminal or microcontroller interface.
• Outputs IEC61937 burst preamble Pc from microcontroller interface.
• Outputs IEC60958 bit 1 of channel status (non-PCM data delimiter bit).
• Outputs emphasis information of channel status.
• Can use up to four LC89058W-Es at the same time by setting the 2-bit chip address.
• Runs on a single 3.3V power supply (S/PDIF input and microcontroller interface support 5V TTL interface.)
• SQFP48 package
Package Dimensions
unit : mm (typ)
3163B
9.0
7.0
36
25
24
13
37
48
1
12
0.5
0.15
0.18
(0.75)
SQFP48(7X7)
No.A1056-2/64
LC89058W-E
4. Pin Assignment
36 35 34 33 32 31 30 29 28 27 26 25
24
23
22
21
20
19
18
17
16
15
14
13
37
38
SDIN
DO
DI
SLRCK
SBCK
39
40
41
42
43
44
45
46
47
48
CE
RDATA
RLRCK
CL
XMODE
DGND
DV
DD
LC89058W-E
DGND
RBCK
RMCK
AGND
DV
DD
GPIO0
GPIO1
GPIO2
AV
DD
GPIO3
LPF
RXOUT2
1
2
3
4
5
6
7
8
9
10 11 12
* : Pull-down resistor internal at no selection
Top view
5. Pin Functions
Table 5.1 Pin Functions
Pin No.
1
Name
I/O
Function
RXOUT1
RX0
O
RX0-6 input S/PDIF through output pin 1
2
I5(pd)
I(pd)
I5(pd)
I5(pd)
5V withstand voltage TTL input level compatible S/PDIF input pin (connected to GND when RX1 is set)
Co-axial compatible S/PDIF input pin (supported demodulation sampling frequency of up to 96kHz)
5V withstand voltage TTL input level compatible S/PDIF input pin (connected to GND when RX1 is set)
5V withstand voltage TTL input level compatible S/PDIF input pin
Digital GND
3
RX1
4
RX2
5
RX3
6
DGND
7
DV
DD
Digital power supply (3.3V)
8
RX4
RX5
RX6
I5(pd)
I5(pd)
I5(pd)
5V tolerable TTL input level compatible S/PDIF input pin
5V tolerable TTL input level compatible S/PDIF input pin
5V tolerable TTL input level compatible S/PDIF input pin
Digital power supply (3.3V)
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
DV
DD
DGND
LPF
Digital GND
O
PLL loop filter connection pin
AV
DD
Analog power supply (3.3V)
AGND
RMCK
RBCK
DGND
Analog GND
O
R system clock output pin (VCO, 512fs, XIN)
R system bit clock I/O pin (64fs)
O/I
Digital GND
DV
DD
Digital power supply (3.3V)
RLRCK
RDATA
SBCK
O/I
O
R system LR clock I/O pin (fs)
Serial audio data output pin
O
S system bit clock output pin (16fs, 32fs, 64fs, 128fs)
S system LR clock output pin (fs/4, fs/2, fs, 2fs)
External serial audio data input pin
SLRCK
SDIN
O
I5
Continued on next page.
No.A1056-3/64
LC89058W-E
Continued from preceding page.
Pin No.
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Name
I/O
Function
DGND
Digital GND
DV
DD
Digital power supply (3.3V)
XMCK
XOUT
XIN
O
O
I
Oscillation amplifier clock output pin
Output pin connected to the resonator
External clock input pin, connected to the resonator (12.288MHz/24.576MHz)
DV
DD
Digital power supply
DGND
MOUT
AUDIO
Digital GND
I/O
I/O
I/O
I/O
O
Emphasis information || Input fs monitor output || Chip address setting input pin
Channel status bit 1 output || Chip address setting input pin
Clock switching transition period signal output || Master/slave setting input pin
Microcontroller interrupt signal output || Pins44-48 I/O setting input pin
PLL lock error, data error flag output pin
CKST
INT
RERR
DO
O
CCB microcontroller I/F, read data output pin (3-state)
CCB microcontroller I/F, write data input pin
CCB microcontroller I/F, chip enable input pin
CCB microcontroller I/F, clock input pin
DI
I5
CE
I5
CL
I5
XMODE
DGND
I5
System reset input pin
Digital GND
DV
DD
Digital power supply (3.3V)
GPIO0
GPIO1
GPIO2
GPIO3
RXOUT2
O/I
O/I
O/I
O/I
O
General-purpose I/O pin || Selector input pin (output referred to RDATA pin)
General-purpose I/O pin || Selector input pin (output referred to RLRCK pin)
General-purpose I/O pin || Selector input pin (output referred to RBCK pin)
General-purpose I/O pin || Selector input pin (output referred to RMCK pin)
RX0-6 input S/PDIF through output pin 2
* Input voltage: I= -0.3 to 3.6V, I5 = -0.3 to 5.5V
* Output voltage: O= -0.3 to 3.6V
* Pins 2, 4, 5, 8, 9, 10, 24, 38, 39, 40, and 41 have an internal pull-down resistor (pd).
Their level is fixed when they are unselected.
* Pins 32 and 33 are input pins for chip address setting when pin 41 is held at the low level.
* Pin 34 serves as the input pin for designating as the master or slave when pin 41 is held at the low level.
* Pin 35 serves as the input pin for configuring the I/O of pins 44 to 47 when pin 41 is held at the low level.
* The DV
and AV pins must be held at the same level and turned on and off at the same timing to preclude
DD
DD
Latch-up conditions.
No.A1056-4/64
LC89058W-E
6. Block Diagram
MOUT
32
INT
AUDIO
33
35
XMODE
41
Fs calculator
GPIO0
GPIO1
GPIO2
GPIO3
44
45
46
47
CL
CE
DI
40
39
38
37
Microcontroller
I/F
Cbit, Pc
DO
RXOUT2
RXOUT1
48
1
RX0
RX1
RX2
RX3
RX4
RX5
RX6
2
3
RERR
36
24
21
Demodulation
&
Lock detect
SDIN
4
Data
Selector
Input
Selector
5
RDATA
8
9
RMCK
PLL
16
10
RBCK
17
20
Clock
Selector
LPF
13
Clock
Divider
RLRCK
XIN
XOUT
XMCK
29
28
27
SBCK
22
23
Oscillation
Amplifier
SLRCK
34
CKST
Figure 6.1 LC89058W-E Block Diagram
No.A1056-5/64
LC89058W-E
7 Common and Different Points between LC89057W-VF4A-E and LC89058W-E
7.1 Common Features
Table 7.1: Common of LC89057W-VF4A-E and LC89058W-E functions (Hardware/Software Compatibility)
Item
LC89057W-VF4A-E
LC89058W-E
Package
SQFP48(9x9)
←
←
←
←
Supply voltage
3.3V single source
DIR reception range
32kHz to 192kHz
Oscillation amplifier input frequency
2-system-clock pin output
S/PDIF inputs
12.288MHz/24.576MHz
RMCK, RBCK, RLRCK, SBCK, SLRCK
7 maximum (1 coaxial, 6 optical)
SDIN
← SBCK: 16fs, SLRCK: 1/4 output added
←
Serial data input
←
AUDIO
Non-PCM flag output
←
Emphasis information output
DTS-CD/LD detection function
General-purpose I/O
EMPHA (consumer and professional)
14-bit format detection supported
4 bits
← MOUT (consumer only)
←
←
Chip address setting
4 addresses maximum (master/salve supported)
4 resistors used
←
Mode setting external resistor
Microcontroller interface
Register configuration
←
CCB (Our company proprietary IF)
4 command address bits, 8 data bits
← DI input regulations has.
←
7.2 Removed Functions
Table 7.2: Differences between LC89057W-VF4A-E and LC89058W-E (Removed Functions)
Item
LC89057W-VF4A-E
LC89058W-E
Modulation removed (demodulation only)
Removed
Function
Modulation and demodulation
S/PDIF unlock path switching
External clock synchronization mode
R and S system clock synchronization
Data output format
Yes
Yes
Removed
Asynchronous system
Synchronization clock (SELMTD, RCKSEL removed)
Right-justified removed (left-justified MSB, I2S only)
Removed
16, 20, 24 bits/left-justified/right-justified MSB, I2S
C, V, U pin output
Yes
Input fs computed output
16kHz to 192kHz
32kHz to 192kHz (fs < 32kHz, removed)
Pulse output mode removed (level output only)
Microcontroller interrupt signal
Yes (Low pulse, Low level output)
7.3 Added or Modified Functions
Table 7.3: Differences between LC89057W-VF4A-E and LC89058W-E (Added or Modified Functions)
Item
LC89057W-VF4A-E
Suspended while PLL is locked
256fs or 512fs
LC89058W-E
Page
19
Oscillation amplifier initial setting
PLL clock output
Permanent operation
512fs
20-26
22
Master clock output
Multiple of input fs is output
No limitation
Multiple of input fs on each band is output
RBCK and SBCK must 1/2 or less of RMCK
Switched during the CKST pulse output
Polarity can be switched
Clock output when XIN source
Clock switching
23
Clock count is preserved (to maintain continuity)
Polarity cannot be switched
Reflected only to error flag.
32kHz to 96kHz (XIN=24.57M/12.28MHz)
Microcontroller interface output only
No timing control
25
RMCK and CKST polarity
S/PDIF reception limitation
S/PDIF input detection range
Input fs value monitor output
General-purpose I/O input pin
General-purpose I/O input/output pin
23, 25
26
Reflected to both error flag and clock output
32kHz to 192kHz (XIN=24.576MHz only)
Microcontroller interface and pin outputs
Polling supported (with interrupt)
Internal selector input also supported.
27
32
36
Parallel I/O function only
37
No.A1056-6/64
LC89058W-E
7.4 Differences in Microcontroller Registers
7.4.1 Differences in write commands
Table 7.4: LC89057W-VF4A-E Write Register Map
Addr
Setting Item
DI15
TESTM
PBSEL1
AMPOPR1
XRLRCK1
XSLRCK1
0
DI14
DI13
TXOPR
FSLIM1
EXSYNC
XRBCK1
XSBCK1
RDTSTA
ROSEL1
RLRCKP
PCRNW
FSERR
PI1
DI12
RXOPR
FSLIM0
PLLOPR
XRBCK0
XSBCK0
RDTSEL
ROSEL0
RBCKP
UNPCM
RESTA
PI0
DI11
DI10
0
DI9
DOEN
VOSEL
XINSEL
PRSEL1
PSBCK1
OCKSEL
RISEL1
OFSEL1
INDET
REDER
VISEL
TXLRP
0
DI8
SYSRST
UOSEL
PLLSEL
PRSEL0
PSBCK0
SELMTD
RISEL0
OFSEL0
ERROR
RESEL
UISEL
TXDFS
0
0
All system
0
INTOPF
1
Demodulator system
Master clock
PBSEL0
AMPOPR0
XRLRCK0
XSLRCK0
RDTMUT
ROSEL2
SBCKP
SLIPO
ERWT0
PI2
RXMON
AOSEL
XMSEL0
XRSEL0
PSLRCK0
RCKSEL
RISEL2
OFSEL2
FSCHG
XTWT0
VMODE
TDTSEL
0
2
XMSEL1
3
R system output clock
S system output clock
Source switching
Data input/output
Output format
XRSEL1
4
PSLRCK1
5
0
6
RXOFF
SLRCKP
EMPF
ERWT1
PI3
ULSEL
7
0
INT
8
source selection
CSRNW
9
RERR conditions
XTWT1
10
11
12
13
14
15
Modulation system
0
Modulation data
TCKSEL
0
0
TXMOD1
0
TXMOD0
0
TXMUT
Test
Test
Test
Test
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 7.5: LC89058W-E Write Register Map
Addr
Setting Item
System setting 1
System setting 2
Master clock
DI15
TESTM
“0”
DI14
DI13
“0”
DI12
“0”
DI11
DI10
0
DI9
DOEN
“0”
DI8
SYSRST
MOSEL
“0”
0
0
“0”
1
“0”
FSLIM1
“0”
FSLIM0
PLLOPR
XRBCK0
XSBCK0
RDTSEL
ROSEL0
RBCKP
UNPCM
RESTA
PI0
RXMON
AOSEL
XMSEL0
XRSEL0
PSLRCK0
0
2
AMPOPR1
XRLRCK1
XSLRCK1
0
AMPOPR0
XRLRCK0
XSLRCK0
RDTMUT
ROSEL2
SBCKP
GPIO
XMSEL1
XINSEL
PRSEL1
PSBCK1
OCKSEL
RISEL1
“0”
3
R system output clock
S system output clock
Source switching
Data input/output 1
Output format
XRBCK1
XSBCK1
RDTSTA
ROSEL1
RLRCKP
PCRNW
FSERR
PI1
XRSEL1
PRSEL0
PSBCK0
0
4
PSLRCK1
5
0
6
“0”
“0”
RISEL2
“0”
RISEL0
OFDSEL
ERROR
RESEL
“0”
7
SLRCKP
EMPF
ERWT1
PI3
0
INT
8
source selection
CSRNW
FSCHG
“0”
INDET
REDER
“0”
9
RERR condition setting
General-purpose I/O
Test
ERWT0
PI2
“0”
10
11
12
13
14
15
0
“0”
“0”
0
“0”
“0”
“0”
“0”
“0”
“0”
System setting 3
Data input/output 2
Other output settings
Test
0
0
CKSTP
RXSEL1
0
RMCKP
RXSEL0
0
0
PLLDV1
EMCKP
PTOXW0
0
PLLDV0
EXTSEL
0
PLLACC
GPIOS
0
0
RXSEL2
FSSEL0
0
EDTMUT
PTOXW1
0
FSSEL1
0
0
0
0
0
• Except MOSEL, PRSEL [1:0], OFDSEL, GPIO, SELMTD and RCKSEL, the command address of any inadvertently
specified commands that are removed from the LC89057W-VF4A-E is assumed to be “0” and ignored.
The new commands added to the LC89058W-E are allocated to command addresses 12, 13, and 14.
No.A1056-7/64
LC89058W-E
7.4.2 Differences in read commands
Table 7.6: Changes in the Register Function between LC89057W-VF4A-E and LC89058W-E
CCB Address
0xE9
LC89057W-VF4A-E
LC89058W-E
Removed
DIT channel status write register
Table 7.7: Differences in Read Registers between the LC89057W-VF4A-E and LC89058W-E
LC89057W-VF4A-E
LC89058W-E
Register
0xEA
RXDET0
RXDET1
RXDET2
RXDET3
RXDET4
RXDET5
RXDET6
RXDET7
OERROR
OINDET
OFSCHG
OCSRNW
OUNPCM
OPCRNW
OSLIPO
OEMPF
CSBIT1
IEC1937
DTS51
0xEB
0xEA
RXDET0
RXDET1
RXDET2
RXDET3
RXDET4
RXDET5
RXDET6
0
0xEB
DO0
DO1
PO0
PO0
PO1
PO1
DO2
PO2
PO2
DO3
PO3
PO3
DO4
FSC0
FSC0
DO5
FSC1
FSC1
DO6
FSC2
FSC2
DO7
FSC3
FSC3
DO8
FSDAT0
OERROR
OINDET
OFSCHG
OCSRNW
OUNPCM
OPCRNW
OGPIO
OEMPF
CSBIT1
IEC1937
DTS51
DTSES
0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
DO9
FSDAT1
DO10
DO11
DO12
DO13
DO14
DO15
DO16
DO17
DO18
DO19
DO20
DO21
DO22
DO23
FSDAT2
FSDAT3
FSDAT4
FSDAT5
FSDAT6
FSDAT7
-
-
-
-
-
-
-
-
DTSES
F0512
F1024
0
F2048
0
F4096
0
• The CCB addresses 0xEC and 0xED remain the same for both the LC89057W-VF4A-E and LC89058W-E.
No.A1056-8/64
LC89058W-E
7.5 Points to Notice about Replacing
• When replacing the LC89057W-VF4A-E with the LC89058W-E, it may be necessary to review the circuit pattern
design of the printed circuit board in advance depending how the device is used. Particular attention should be
directed to pins 44 to 48 whose I/O functionality can be set according to the INT pin setting. This section contains
the notes and cautions to be observed when replacing the LC89057W-VF4A-E with the LC89058W-E. For details of
the INT pin, see Chapter 9, Initial System Settings and Chapter 10, Description of Demodulation Function.
• Refer to the specifications of LC89057W-VF4A-E when replacing LC89058W-E with LC89057W-VF4A-E.
Table 7.8: Differences between LC89057W-VF4A-E and LC89058W-E (Pins 44 to 48)
INT
Pin
LC89057W-VF4A-E
Modulation function
Pin.46
LC89058W-E
General-purpose I/O function
S/PDIF
Pin.48
Pin.44
TMCK
Input
Pin.45
TBCK
Input
Pin.47
TDATA
Input
Pin.48
TXO
Pin.44
GPIO0
Input
Pin.45
GPIO1
Input
Pin.46
GPIO2
Input
Pin.47
GPIO3
Input
Pull-down
Pull-up
TLRCK
RXOUT2
Output
S/PDIF
Pin.48
Input
Output
General-purpose I/O function
General-purpose I/O function
Pin.44
PIO0
Pin.45
Pin.46
PIO2
Pin.47
Pin.48
PIOEN
Input
Pin.44
GPIO0
Output
Pin.45
GPIO1
Output
Pin.46
GPIO2
Output
Pin.47
GPIO3
Output
PIO1
PIO3
RXOUT2
Output
In/Output
In/Output
In/Output
In/Output
7.5.1 Change from LC89057W-VF4A-E to LC89058W
7.5.1 When the INT pin is set to pull-down
Print Board
LC89057W-VF4A-E
LC89058W-E
Pin. 35
INT
INT
Pin. 35
TMCK
Pin. 44
TBCK
GPIO0
Pin. 44
Pin. 45
Pin. 46
Pin. 47
Pin. 48
GPIO1
GPIO2
Pin. 45
TLRCK
Pin. 46
TDATA
Pin. 47
TXO
GPIO3
RXOUT2
Pin. 48
Figure 7.1 Change from LC89057W-VF4A-E to LC89058W-E (when the INT pin is set to pull-down)
• In this case, the system that doesn't use a modulation function or a general-purpose I/O function can be replaced with
LC89058W-E.
• After the replacement, LC89058W-E is used on condition that it pins 44 to 47 connect with GND and pin 48 open.
No.A1056-9/64
LC89058W-E
7.5.1.2 When the INT pin is set to pull-up
7.5.1.2.1 In case of “Pin 48 = GND”
Print Board
LC89057W-VF4A-E
LC89058W-E
INT
INT
Pin. 35
Pin. 35
PIO0
GPIO0
GPIO1
GPIO2
GPIO3
Pin. 44
PIO1
Pin. 44
Pin. 45
Pin. 46
Pin. 47
Pin. 45
PIO2
Pin. 46
PIO3
Pin. 47
PIOEN
Pin. 48
RXOUT2
Pin. 48
JP
Open when LC89058W-E use
Figure 7.2 Change from LC89057W-VF4A-E to LC89058W-E (when the INT pin is set to pull-up) 1
• After the replacement, pins 44 to 47 can be used as general purpose I/O output function. (pin 48 open)
• It is necessary to review the circuit pattern of the printed circuit board because the I/O setting of pin 48 differs from
each other.
7.5.1.2.2 In case of “Pin 48 = V
”
DD
Print Board
LC89057W-VF4A-E
LC89058W-E
Pin. 35
JP
INT
INT
Pin. 35
PIO0
PIO1
PIO2
PIO3
Pin. 44
Pin. 45
Pin. 46
Pin. 47
GPIO0
GPIO1
Pin. 44
Pin. 45
Pin. 46
Pin. 47
Pin. 48
GPIO2
GPIO3
PIOEN
RXOUT2
Pin. 48
JP
Open when LC89058W-E use
Figure 7.3 Change from LC89057W-VF4A-E to LC89058W-E (when the INT pin is set to pull-up) 2
• It is necessary to review the circuit pattern of the printed circuit board to change the pull-up resistor of pin 35 to the
pull-down resistor because pins 44 to 47 is used as general purpose I/O input function.
• It is necessary to review the circuit pattern of the printed circuit board because the I/O setting of pin 48 differs from
each other.
No.A1056-10/64
LC89058W-E
7.5.2 Change from LC89058W-E to LC89057W-VF4A-E
7.5.2.1 When the INT pin is set to pull-down
Print Board
LC89058W-E
JP
LC89057W-VF4A-E
Pin. 35
INT
INT
Pin. 35
PIO0
PIO1
PIO2
PIO3
Pin. 44
Pin. 45
Pin. 46
Pin. 47
GPIO0
Pin. 44
GPIO1
Pin. 45
GPIO2
Pin. 46
GPIO3
Pin. 47
PIOEN
Pin. 48
RXOUT2
Pin. 48
JP
Short when LC89057W-VF4A-E use
Figure 7.4 Change from LC89058W-E to LC89057W-VF4A-E (when the INT pin is set to pull-down)
• It is necessary to review the circuit pattern of the printed circuit board to change the pull-up resistor of pin 35 to the
pull-down resistor because pins 44 to 47 is used as general purpose I/O input function.
• It is necessary to review the circuit pattern of the printed circuit board because the I/O setting of pin 48 differs from
each other.
• After the replacement, the RXOUT2 output of LC89057W-VF4A-E cannot be used.
7.5.2.2 When the INT pin is set to pull-up
Print Board
LC89058W-E
LC89057W-VF4A-E
Pin. 35
INT
INT
Pin. 35
GPIO0
GPIO1
GPIO2
GPIO3
PIO0
PIO1
PIO2
PIO3
Pin. 44
Pin. 45
Pin. 46
Pin. 47
Pin. 44
Pin. 45
Pin. 46
Pin. 47
RXOUT2
PIOEN
Pin. 48
Pin. 48
JP
Short when LC89057W-VF4A-E use
Figure 7.5 Change from LC89058W-E to LC89057W-VF4A-E (when the INT pin is set to pull-up)
• After the replacement, pins 44 to 47 can be used as general purpose I/O output function. However, it is necessary to
review the circuit pattern of printed circuit board because pin 48 has to GND.
• After the replacement, the RXOUT2 output of LC89057W-VF4A-E cannot be used.
No.A1056-11/64
LC89058W-E
8. Electrical Characteristics
8.1 Absolute Maximum Ratings
Table 8.1: Absolute Maximum Ratings at AGND = DGND = 0V
Parameter
Maximum supply voltage
Maximum supply voltage
Input voltage 1
Symbol
Conditions
Ratings
Unit
V
AV
DV
V
max
8-1-1
8-1-2
8-1-3
8-1-4
8-1-5
-0.3 to +4.6
-0.3 to +4.6
DD
max
DD
V
1
-0.3 to V +0.3 (max.3.9V)
DD
V
IN
Input voltage 2
V
2
-0.3 to +5.8
V
IN
Output voltage
V
-0.3 to V +0.3 (max.3.9V)
DD
V
OUT
Storage ambient temperature
Operating ambient temperature
Maximum input/output current
Tstg
Topr
-55 to +125
-30 to +70
20
°C
°C
mA
I
, I
IN OUT
8-1-6
8-1-1: AV
8-1-2: DV
pin
pin
DD
DD
8-1-3: RX1, RBCK, RLRCK, XIN, GPIO0, GPIO1, GPIO2, GPIO3 pins
8-1-4: RX0, RX2, RX3, RX4, RX5, RX6, SDIN, DI, CE, CL, XMODE pins
_________
8-1-5: RXOUT1, RMCK, RBCK, RLRCK, RDATA, SBCK, SLRCK, XMCK, XOUT, MOUT, AUDIO pins,
_____
CKST, INT, RERR, DO, GPIO0, GPIO1, GPIO2, GPIO3, RXOUT2 pins
8-1-6: Per input/output pin
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
8.2 Allowable Operating Ranges
Table 8.2: Recommended Operating Conditions at AGND = DGND = 0V
Ratings
Parameter
Symbol
Conditions
Unit
min
typ
max
Supply voltage
AV , DV
3.0
0
3.3
3.3
3.3
3.6
V
V
DD
1
DD
Input voltage range 1
Input voltage range 2
Operating temperature
V
V
8-2-1
8-2-2
AV , DV
DD
IN
DD
5.5
2
0
V
IN
Topr
-30
70
°C
8-2-1: RX1, RBCK, RLRCK, XIN, GPIO0, GPIO1, GPIO2, GPIO3 pins
8-2-2: RX0, RX2, RX3, RX4, RX5, RX6, SDIN, DI, CE, CL, XMODE pins
No.A1056-12/64
LC89058W-E
8.3 DC Characteristics
Table 8.3: DC Characteristics at Ta = -30 to 70°C, AV
= DV
= 3.0 to 3.6V, AGND = DGND = 0V
DD
DD
Ratings
Parameter
Symbol
Conditions
Unit
min
typ
max
Input, High
Input, Low
V
V
V
V
V
V
V
V
V
V
V
V
V
I
8-3-1
8-3-2
8-3-3
8-3-4
8-3-5
8-3-6
0.7V
V
V
IH
DD
2.0
0.2V
IL
DD
5.8
Input, High
Input, Low
V
IH
-0.3
-0.8
0.8
0.4
0.4
0.4
0.4
40
V
IL
Output, High
Output, Low
Output, High
Output, Low
Output, High
Output, Low
Output, High
Output, Low
V
V
V
V
V
OH
OL
OH
OL
OH
OL
OH
OL
PP
DD
DD
DD
DD
V
-0.8
-0.8
-0.8
200
25
V
V
V
V
V
V
Input amplitude
8-3-7
8-3-8
8-3-9
mV
mA
kΩ
Consumption current
Pull-down resistance
DD
R
50
100
DN
8-3-1: CMOS compatible: RBCK, RLRCK input pins during XIN and slave settings
8-3-2: TTL compatible: Input pins other than those listed above
8-3-3: I
8-3-4: I
8-3-5: I
= −12mA, I
= 8mA: RMCK output pin
= 8mA: XOUT, XMCK output pins
= 4mA: RXOUT1, RBCK, RLRCK, RDATA, SBCK, SLRCK, RERR, MOUT,
GPIO0, GPIO1, GPIO2, GPIO3, RXOUT2 output pins
OH
OH
OH
OL
= −8mA, I
= −4mA, I
OL
OL
8-3-6: I
= −2mA, I
= 2mA: Output pins other than those listed above
OH
OL
8-3-7: Before capacitance of RX1 input pin, and reception frequency is possible up to 96kHz.
8-3-8: Ta=25°C, fs=96kHz
8-3-9: RX0, RX2, RX3, RX4, RX5, RX6 input pins
No.A1056-13/64
LC89058W-E
8.4 AC Characteristics
Table 8.4: AC Characteristics at Ta=-30 to 70°C, AV =DV =3.0 to 3.6V, AGND=DGND=0V
DD
DD
Ratings
Parameter
Symbol
Conditions
Unit
min
typ
max
195
RX0, RX2 to RX6 fs frequency
RX1 fs frequency
f
f
t
t
t
f
f
28
28
20
40
40
12
4
kHz
kHz
ns
RFS1
108
RFS2
WDI1
WDI2
DUY
XF
RX0, RX2 to RX6 pulse width
RX1 pulse width
ns
RX0 to RX6 duty factor
XIN clock frequency
RMCK clock frequency
RMCK clock jitter
60
25
50
%
8-4-1
MHz
MHz
ps
MCK
tj
t
200
RMCK, RBCK delay
RBCK, RDATA delay
RMCK, SBCK delay
SBCK, RDATA delay
10
10
10
10
ns
MBO
t
t
t
ns
BDO
MBO
BDO
8-4-2
8-4-3
ns
ns
8-4-1 A frequency compatible with the XINSEL setting must be applied to XIN.
8-4-2: When RMCK and SBCK source clocks are identical
8-4-3: When SBCK is the PLL source clock
t
t
DUY
WDI
RX0-6 (I)
t
WDI
t
DUY
RMCK (O)
(RMCKP=0)
t
MBO
F
MCK
RBCK (O)
RLRCK (O)
RDATA (O)
t
BDO
Figure 8.1 AC Characteristics of Demodulation function
No.A1056-14/64
LC89058W-E
8.5 CCB Microcontroller Interface AC Characteristics
Table 8.5: CCB Microcontroller Interface AC Characteristics at Ta=-30 to 70°C, AV =DV =3.0 to 3.6V,
DD
DD
AGND=DGND=0V
Ratings
typ
Parameter
Symbol
RST dw
Conditions
Unit
min
max
XMODE pulse width, Low
t
t
t
t
200
100
100
50
μs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
CL pulse width, Low
CL pulse width, High
CL to CE setup time
CL dw
CL uw
CE setup
CL to CE hold time
CL to CE hold time
CL to DI setup time
CL to DI hold time
CL to CE hold time
CL to DO delay time
CE to DO delay time
DI pulse width
t
t
t
t
t
t
t
t
8-5-1
8-5-2
50
0
CE hold
CE hold
DI setup
DI hold
50
50
50
CL hold
CL to DO
CE to DO
DI dw
20
20
8-5-3
200
8-5-1: CL has to lower before CE is H when CL is normal H clock.
8-5-2: Only when data write with CL of normal H clock.
8-5-3: DI has to L period for the reset period when DI is normal H.
DV
AV
DD
DD
t
RSTdw
XMODE (I)
CL (I)
t
t
CLuw CLdw
t
CEsetup
t
CEhold
CE (I)
t
CLhold
t
t
t
DIhold
DIdw
DIsetup
DI (I)
t
t
CLtoDO
CEtoDO
DO (O)
Hi-z
Figure 8.2 CCB Microcontroller Interface AC Characteristics
No.A1056-15/64
LC89058W-E
9. Initial System Settings
9.1 System Reset (XMODE)
• The system operates correctly when XMODE is set to "H" after 3.0V or higher supply voltage is applied.
When XMODE is set to "L" after power is turned on, the system is reset.
• To set chip address, master/slave, or pins 44 to 47 I/O, 10kΩ pull-down or pull-up resistors must be connected to
MOUT, AUDIO , CKST, and INT .
• If none of MOUT, AUDIO , CKST, and INT are pulled down or pulled up, their pin state will get unstable when the
settings are entered, resulting in wrong setting. Pull-up or pull-down resistors must be connected to these pins without
fail.
Table 9.1: Pin Names and Settings
Pins
Setting
MOUT
AUDIO
Chip address
CKST
INT
Master/slave setting
Pins 44 to 47 I/O setting
Normal system operation range
Setting
completed
Setting
completed
Resetting
3.0V
DV
DD
t
t > 200μs
XMODE
Set pin state
Undefined
Setting input state Output state
Setting input state Output state
Figure 9.1 Setting Timing Chart of Function Setting Input Pins
Table 9.2: Output Pin State When XMODE is Reset (XMODE=L)
No.
1
Pin name
RXOUT1
RMCK
Pin State
RXO output
XIN output
Low output
High output
Low output
Low output
High output
XIN output
No.
32
33
34
35
36
37
48
Pin name
Pin State
Input state
Input state
Input state
Input state
High output
Hi-z output
Low output
MOUT
AUDIO
16
17
20
21
22
23
27
RBCK
CKST
INT
RLRCK
RDATA
SBCK
RERR
DO
SLRCK
XMCK
RXOUT2
No.A1056-16/64
LC89058W-E
___________
9.2 Chip Address Settings (MOUT, AUDIO)
• The LC89058W-E comes with a function to set a unique chip address to allow the use of several LC89058W-E on the
same microcontroller interface bus.
____________
• In chip address setting, connect a 10kΩ pull-down or pull-up resistor to MOUT and AUDIO. By this setting, 4 kinds
of chip addresses can be set at a maximum.
• Chip addresses in the microcontroller interface are set with CAL and CAU provided as the first two bits on the LSB
side. CAL corresponds to the lower chip address and CAU to the higher chip address.
____________
• Command writing is enabled by making the chip address settings with MOUT and AUDIO identical to the chip
addresses sent from the microcontroller.
• The chip address setting is required even when only one LC89058W-E is used in the system. If the chip address is not
set, the chip address is undefined and the microcontroller cannot control the system. When the microcontroller is not
used, a chip address-setting pin is input open while XMODE is "L". Be sure to connect either a pull-down resistor or a
____________
pull-up resistor to MOUT and AUDIO.
Table 9.3: Chip Address Settings (Resistor Connection)
_____
AUDIO
Pull-down
Pull-down
Pull-up
MOUT
Pull-down
Pull-up
CAU
CAL
0
0
1
1
0
1
0
1
Pull-down
Pull-up
Pull-up
LC89058W-E
pull-up 10kΩ
MOUT
Connect to
different circuits
AUDIO
CKST
INT
pull-down 10kΩ
Setting Contents of Above Figure
Chip address setting
CAL=CAU=0
Master
Pins 44 to 47 output pins
Master or slave setting
Pins 44 to 47 input or output setting
Figure 9.2 Setting Example of Function Setting Input Pin
No.A1056-17/64
LC89058W-E
9.3 Master/Slave Settings (CKST)
• A master/slave function that allows multi-channel synchronized transfer using multiple LC89058W-Es is included.
For this setting, connects either a 10kΩ pull-down or a pull-up resistor to CKST.
• Set to the master mode normally, when single LC89058W-E IC is used. When multiple LC89058W-Es are used, set
one of them to the master mode and the others to the slave mode.
• In the multi-channel synchronous transfer mode using multiple LC89058W-Es, connect RBCK and RLRCK (output)
on the master side to RBCK and RLRCK (input) on the slave side. Also connect XMCK on the master side to XIN on
the slave side. At this time, the polarity of RBCK and RLRCK, and the frequency of XIN and XMCK must be
identical.
• The master/slave function runs correctly with the multiple LC89058W-Es connected.
• Be sure to connect either a pull-down resistor or a pull-up resistor to CKST.
• Always supply the clock to RBCK and RLRCK when the slave function is set.
Table 9.4: Master/Slave Switching (Register Connection)
CKST
Pull-down
Pull-up
Mode
Master
Slave
Table 9.5: Clock Pin State
Pin
Master mode
Slave mode
RMCK
RBCK
RLRCK
Output
Output
Input
Output
Output
Input
9.4 Pins 44 to 47 I/O settings (INT )
• Pins 44 to 47 are provided with a bidirectional buffer.
• When setting I/O function of pins 44 to 47, connect a 10kΩ pull-down or pull-up resistor to INT .
• Be sure to connect either a pull-down resistor or a pull-up resistor to INT .
Table 9.6: P_in__s 44 to 47 I/O Settings (Resistor Connection)
INT
Mode
Pull-down
Pull-up
Input.
Output.
No.A1056-18/64
LC89058W-E
10 Description of Demodulation Function
10.1 Clocks
10.1.1 PLL (LPF)
• The LC89058W-E incorporates a VCO (Voltage Controlled Oscillator) that
can be stopped with PLLOPR and it synchronizes with sampling frequencies (fs)
from 32kHz to 192kHz and with the data with transfer rate from 4MHz to
25MHz. PLL is locked at 512fs.
LPF
• LPF is a pin for PLL loop filter. Connect the following resistance and capacitance
shown in the figure.
R0
C1
R0 : 220Ω
C0
C0 : 0.1μF
C1 : 0.022μF
Figure 10.1 Loop Filter Configuration
10.1.2 Oscillation amplifiers (XIN, XOUT, XMCK)
• The LC89058W-E features a built-in oscillation amplifier. Connecting a quartz resonator, feedback resistor, and load
capacitance to XIN and XOUT can configure an oscillation circuit. When connecting a quartz resonator, use one with
a fundamental wave. Be aware that the load capacitance depends on the quartz resonator characteristics.
• If the built-in oscillation amplifier is not used and oscillation module is used as the clock source instead, connect the
output of an external clock supply source to XIN. At this time, it is not necessary to connect a feedback resistor
between XIN and XOUT.
• Always supply XIN with the 12.288MHz or 24.576MHz clock set with XINSEL. If supplying other frequencies to
XIN, it is necessary to set that the result of change in sampling frequency fs of input data with FSERR is not reflected
to an error flag. By this setting, the operation functions properly. Since it is not a recommended frequency, it cannot
be used for input fs calculations.
• The setting of XINSEL must be completed prior to S/PDIF input.
• Supply XIN with clocks all the time to be used in the following applications.
(1) Detection of presence or absence of S/PDIF input
(2) Clock source while PLL is unlocked
(3) Calculation of input data sampling frequency
(4) Time definition when switching input data
(5) External source of supply clock (clock for an AD converter, etc.) in XIN source mode.
(6) Polling processing performed when setting the general-purpose I/O input function
• The oscillation amplifier runs even when the PLL is locked. Therefore, data detection and calculation of input
sampling frequency become possible while the PLL is locked. In that case, both the oscillation amplifier clock and the
PLL clock signals coexist, and then user must pay attention and make sure sound quality is not adversely affected.
• If adverse effects on the sound quality are recognized, it is possible to set with the AMPOPR [1:0] that the oscillation
amplifier automatically stop operation while the PLL is locked. Therefore, setting of the AMPOPR [1:0] must be
completed either prior to S/PDIF input or while PLL is unlocked.
• The oscillation amplifier can be stopped if it is unnecessary. However, when the normal operation is resumed, it must
wait for 10ms or longer until the resonator oscillation gets stable.
• XMCK outputs the XIN clock. The XMCK output is set with XMSEL [1:0]. The XIN clock can be set to 1/1, 1/2, 1/4,
or muted output.
• If you use only the oscillation amplifier, input the quartz resonator to XIN and XOUT or an external clock to XIN,
and fix the electric potential of digital data input pins of RX0 to RX6, or set with RISEL [2:0] that all the inputs are
deselected.
No.A1056-19/64
LC89058W-E
10.1.3 Switching between master clock and clock source
• The RMCK, RBCK, and RLRCK (hereunder, R system), and the SBCK and SLRCK (hereunder, S system) clock
sources can be selected between the following two master clocks.
(1) PLL source (512fs)
(2) XIN source (12.288MHz or 24.576MHz)
• Clock source switching is to set with the R and S systems interlocked. This setting is carried out with OCKSEL.
• The clock source is automatically switched to the PLL or XIN clock by locking/unlocking the PLL. The clock source
can be switched to XIN with OCKSEL, regardless of the PLL status.
Table 10.1: Relationship between Clock Source Switch Commands and Clock Sources when PLL Locked/Unlocked
R System Clock Source
S System Clock Source
OCKSEL
Locked
PLL
Unlocked
XIN
Locked
PLL
Unlocked
XIN
0
1
XIN
XIN
XIN
XIN
• The PLL status can be always monitored with RERR even after switching to the XIN source. Moreover, the processed
information can be read with the microcontroller interface regardless of the PLL status.
10.1.4 Points to notice about switching clock source while PLL is locked
• It is necessary to set the oscillation amplifier to the continuous operation mode at the same time with AMPOPR [1:0]
to do the clock switch to the XIN source with OCKSEL when the oscillation amplifier has stopped in the state where
the PLL is locked. The clock is not output when switching to the XIN clock source without executing this setting.
• In the state where the PLL is locked, if the clock is switched to XIN source with OCKSEL while the oscillator
amplifier is stopped, RERR is temporarily outputs an error (high level) indication. When switched to XIN source, the
oscillator amplifier is switched to the operating state at the same time.
RERR is temporality outputs an error (H level) indication when the oscillation amplifier switches from the stop
condition to the continuous mode. Consequently the input fs calculation restarts. At this time, the previous fs
calculation value is reset and compared with the newly calculated fs value. Then those two values are found not
identical, that’s why the error is temporarily issued.
No.A1056-20/64
LC89058W-E
10.1.5 Master clock block diagram (XIN, XOUT, RMCK, XMCK)
• The relationships between the two types of PLL and XIN source master clocks, switching, and the frequency division
function are described below.
• The contents in the quotation marks “*** “ by the switch and function blocks correspond to the write command names.
• Lock/Unlock is automatically switched by PLL locking/unlocking.
Lock/Unlock
“PLLDV1”
“PLLDV2”
“PLLOPR”
“PLLACC”
S/PDIF
PLL
512fs
Auto 1/N
(N=1,2,4)
1/N
(N=1,2,4)
“OCKSEL”
“PRSEL[1:0]”
XOUT
XIN
“XINSEL”
“XRSEL[1:0]”
1/N
(N=1,2,4)
12.288M
24.567M
“RMCKP”
“AMPOPR[1:0]”
GPIO0
RMCK
XMCK
“EXTSEL”
“EMCKP”
“XMSEL[1:0]”
1/N
(N=1, 2)
Figure 10.2 Master Clock Block Diagram
No.A1056-21/64
LC89058W-E
10.1.6 PLL clock output
• The PLL clock output is controlled by the PLLACC, PLLDV1, PLLDV2, or PRSEL[1:0].
• PLLACC can be used to generate a PLL lock frequency for each S/PDIF input sampling frequency band.
S/PDIF Input
*: When the data is judged to exceed the value of
FSLIM [1:0] which limits the reception frequency of
the input S/PDIF, processing similar to PLL
512fs
Lock detection
Unlock
unlocking is carried out and the processing does not
proceed to the subsequent step. The clock source is
automatically switched to the XIN source.
Lock
PLL output
Free-run
Fs calculation
*
0
“PLLACC”
1
PLL fixation output
“PRSEL=00”: 256fs
“PRSEL=01”: 512fs
“PRSEL=10”: 128fs
Fs=
No
32k, 44.1k, 48k
Yes
Fs=
No
64k, 88.2k, 96k
0
“PLLDV0”
1
Yes
Fs=
No
128k, 176.4k, 192k
0
“PLLDV1”
1
Yes
PLL output
256fs
PLL output
512fs
PLL output
128fs
PLL output
256fs
PLL output
512fs
PLL output
256fs
Figure 10.3 PLL Clock Output Control
Table 10.2: PLL Clock Output Frequencies (Bold settings are recommended values.)
PLL Output
S/PDIF
fs
PLLACC=0 (Fixed multiple outputs of input fs)
PLLACC=1 (Fixed multiple outputs for each input fs band)
PRSEL=00
(256fs)
PRSEL=01
(512fs)
PRSEL=10
(128fs)
PLLDV0=0
PLLDV1=0
PLLDV0=1
PLLDV1=0
PLLDV0=0
PLLDV1=1
PLLDV0=1
PLLDV1=1
32kHz
44.1kHz
48kHz
8.19MHz
11.28MHz
12.28MHz
16.38MHz
22.57MHz
24.57MHz
32.76MHz
45.15MHz
49.15MHz
16.38MHz
22.57MHz
24.57MHz
32.76MHz
45.15MHz
49.15MHz
65.53MHz
90.31MHz
98.30MHz
4.09MHz
5.64MHz
6.14MHz
8.19MHz
11.28MHz
12.28MHz
16.38MHz
22.57MHz
24.57MHz
16.38MHz
22.57MHz
24.57MHz
16.38MHz
22.57MHz
24.57MHz
16.38MHz
22.57MHz
24.57MHz
8.19MHz
11.28MHz
12.28MHz
16.38MHz
22.57MHz
24.57MHz
16.38MHz
22.57MHz
24.57MHz
16.38MHz
22.57MHz
24.57MHz
32.76MHz
45.15MHz
49.15MHz
16.38MHz
22.57MHz
24.57MHz
8.19MHz
11.28MHz
12.28MHz
32.76MHz
45.15MHz
49.15MHz
16.38MHz
22.57MHz
24.57MHz
64kHz
88.2kHz
96kHz
128kHz
176.4kHz
192kHz
• If 128kHz, 176.4kHz or 192kHz input is received when the PLLACC is set to 0 and the PRSEL [1:0] to 01, the DC
characteristics of output directly sent to the RMCK pin cannot be guaranteed. In such a case, set the frequency to one
half or quarter of the PLL clock frequency (PRSEL [1:0]=00 or 10).
No.A1056-22/64
LC89058W-E
10.1.7 Output clocks (RMCK, RBCK, RLRCK, SBCK, SLRCK)
• The LC89058W-E features two clock systems (R and S systems) in order to supply the various needed clocks to
peripheral devices such as A/D converter and DSP.
• The clock output settings for the R and S systems are done with PLLACC, PLLDV1, PLLVD2, PRSEL[1:0],
XRSEL[1:0], XRBCK[1:0], XRLRCK[1:0], PSBCK[1:0], PSLRCK[1:0], XSBCK[1:0], and XSLRCK[1:0].
• Setting range for each clock output pin when the PLL is used as source
(1) RMCK: Selection from 1/1, 1/2, and 1/4 of PLLACC, PLLDV0, PLLDV1, or 512fs
(2) RBCK: 64fs output
(3) RLRCK: fs output
(4) SBCK: Selection from 128fs, 64fs, 32fs, and 16fs
(5)SLRCK: Selection from 2fs, fs, 1/2fs, and 1/4fs
• Setting range for each clock output pins when the XIN is used as source
(1) RMCK: Selection from 1/1, 1/2, and 1/4 of 12.288MHz or 24.576MHz
(2) RBCK: Selection from 12.288MHz, 6.144MHz, and 3.072MHz
(3) SBCK: Selection from 12.288MHz, 6.144MHz, and 3.072MHz
(4) RLRCK: Selection from 192kHz, 96kHz, and 48kHz
(5) SLRCK: Selection from 192kHz, 96kHz, and 48kHz
• The polarity of RMCK can be reversed with RMCKP.
• The polarity of RBCK, RLRCK, SBCK, and SLRCK can be reversed with RBCKP, RLRCKP, SBCKP, and SLRCKP.
Table 10.3 List of Output Clock Frequencies (Bold Items = Initial Settings)
PLL Source (Internal VCO CK)
XIN Source (XIN input CK)
Output Pin Name
RMCK
512fs
12.288MHz
24.576MHz
512fs
256fs
128fs
24.576MHz
12.288MHz
6.144MHz
12.288MHz
6.144MHz
12.288MHz
6.144MHz
3.072MHz
(RMCK=24.576MHz)
(RMCK≥12.288MHz)
(RMCK≥6.144MHz)
RBCK
64fs
fs
192kHz
RLRCK
96kHz
48kHz
128fs
64fs
32fs
16fs
2fs
12.288MHz
(RMCK=24.576MHz)
(RMCK≥12.288MHz)
(RMCK≥6.144MHz)
SBCK
6.144MHz
3.072MHz
192kHz
fs
SLRCK
96kHz
fs/2
fs/4
48kHz
Notes:
• RBCK and SBCK output clock must not quicken more than RMCK output clock frequency. Also, RBCK and SBCK
output clock are set to become 1/2 or less of RMCK output clock at XIN source. If it doesn’t follow these conditions,
RBCK and SBCK clocks are not output.
No.A1056-23/64
LC89058W-E
10.1.8 Output clocks block diagram (RMCK, RBCK, RLRCK, SBCK, SLRCK, XMCK)
• The relationships between the output clock and switch function are shown below.
• PLL in the figure indicates the PLL source and XIN the XIN source.
• The contents in the quotation marks “∗∗∗” by the switch function blocks correspond to the write command names.
• The broken lines connecting the switches indicate coordinated switching.
• Lock/Unlock is switched automatically by PLL locking/unlocking.
Input fs
Lock / Unlock
“PLLDV0”
“PLLDV1”
1/1
1/2
1/4
“EXTSEL”
“OCKSEL”
Master
Clock
Generator
512fs
Auto
“PLLACC”
PLL
PLL Source
512fs
“PRSEL[1:0]”
512fs
256fs
128fs
Mute
X’tal Source
12.288MHz
24.576MHz
“RMCKP”
“EMCKP”
“XINSEL”
12.288MHz
24.576MHz
“XRSEL[1:0]”
1/1
1/2
1/4
RMCK
XIN
Mute
GPIO0
“XMSEL[1:0]”
1/1
1/2
XMCK
Mute
PLL
64fs
“XRBCK[1:0]”
12.288MH
6.144MHz
3.072MHz
Mute
XIN
PLL
GPIO1
RBCK
fs
“XRLRCK[1:0]”
192kHz
96kHz
48kHz
Mute
XIN
PLL
GPIO2
RLRCK
“PSBCK[1:0]”
128fs
64fs
32fs
16fs
“SBCKP”
Master / Slave
SBCK
“XSBCK[1:0]”
12.288MH
6.144MHz
3.072MHz
Mute
XIN
PLL
“PSLRCK[1:0]”
2fs
fs
fs/2
fs/4
“SLRCKP”
SLRCK
“XSLRCK[1:0]”
192kHz
96kHz
48kHz
Mute
XIN
Figure 10.4 Clock Output Block Diagram
No.A1056-24/64
LC89058W-E
10.1.9 Output of clock switch transition signal (CKST)
• CKST outputs pulse when the output clock changes by PLL lock/unlock.
• The polarity of the CKST pulse output can be reversed with CKSTP. Subsequently, CKSTP is assumed to be 0.
• In the lock-in stage, the CKST falls at the word clock generated from the XIN clock after PLL is locked following
detection of input data, and rises at the same timing as RERR after a designated period.
• In the unlock stage, the CKST falls at the same timing as RERR, PLL lock detection signal, and rises after word
clocks generated from the XIN clock are counted for a designated period.
• Change of the PLL lock status and timing of the clock change can be seen by detecting the rising and falling edges
and pulses of CKST.
• The clock is switched after the PLL lock condition is tested and identified. The timing of this clock switching is
determined by setting the PTOXW [1:0]. The initial value is such that the clock is switched in 2.7ms after the falling
edge of CKST. The value, however, assumes that the oscillation amplifier is set to permanent operation mode. If the
oscillation amplifier is set to be stopped after PLL locking, the startup time before the oscillation amplifier stabilizes
after PLL unlocking, is added.
• A free-running clock is output from the clock output pin immediately after PLL unlocking.
RX0 to RX6
PLL status
XIN clock
PLL clock
Digital data
UNLOCK
LOCK
After PLL lock
3ms to 144ms
2.7ms
CKST (CKSTP=0)
RERR
RMCK
XIN clock
PLL clock
(a): Lock-in stage
RX0 to RX6
PLL status
XIN clock
PLL clock
Digital data
LOCK
UNLOCK
Same timing as RERR
5.3ms
CKST (CKSTP=0)
RERR
RMCK
2.7ms**
PLL clock
**: When set to PTOXW[1:0]=00 (max.)
(b): Unlock stage
XIN clock
Figure 10.5 Clock Switch Timing
No.A1056-25/64
LC89058W-E
10.1.10 Output clocks generated when input S/PDIF reception is limited
•
The same processing performed when the PLL is unlocked is carried out if an S/PDIF input exceeding the reception
range limit (which can be defined by FSLIM[1:0]) is supplied. The clock source is then switched to the XIN clock and
clocks are output from respective clock pins.
fs=44.1kHz
LOCK
fs=192kHz
LOCK
fs=96kHz
LOCK
DIN0-6
PLL status
RERR
RMCK
RBCK
RLRCK
PLL clock
PLL clock
PLL clock
UNLOCK
(a) When set to FSLIM[1:0]=00 (No limit on inputs)
XIN clock
fs=44.1kHz
LOCK
fs=192kHz
LOCK
fs=96kHz
LOCK
DIN0-6
PLL status
RERR
RMCK
RBCK
PLL clock
XIN clock
PLL clock
RLRCK
(b) When set to FSLIM[1:0]=01 (Receive frequency is limited to 96kHz or lower)
fs=44.1kHz
LOCK
fs=192kHz
LOCK
fs=96kHz
LOCK
DIN0-6
PLL status
RERR
RMCK
RBCK
PLL clock
XIN clock
RLRCK
(c) When set to FSLIM[1:0]=10 (Receive frequency is limited to 48kHz or lower)
Figure 10.6 Output Clocks Generated When Input Data Reception Is Limited
No.A1056-26/64
LC89058W-E
10.2 S/PDIF I/O
10.2.1 Reception range of S/PDIF input
•
The guaranteed reception range of input data is shown below.
Table 10.4: S/PDIF Reception Range (FSLIM [1:0]=00)
PLL Output Clock Setting
512fs
Input Data Reception Range
30kHz to 192kHz
Note:
(1) Reception range of RX1 is 32kHz to 96kHz.
(2) PLL output clock is frequency-divided with PLLACC, PLLDIV and PRSEL [1:0] and is output from RMCK.
•
The fs reception range for input data can be limited within the set range of PLL output clocks stated above. This
setting is carried out with FSLIM [1:0]. When this function is adopted, input data exceeding the set range is
considered as an error, the clock source is automatically switched to the XIN source, and RDATA output data is
subject to the RDTSEL setting.
10.2.2 S/PDIF I/O pins (RX0 to RX6, RXOUT1, RXOUT2)
•
S/PDIF input pins are 7 inputs at maximum.
(1) RX1 is a coaxial-compatible input pin. When using RX1, connect RX0 and RX2 to GND.
(2) RX0, RX2, RX3, RX4, RX5, and RX6 are TTL input level pins with 5V-tolerance voltage.
(3) Make sure that the selected pins are not input-open. For points to notice on RX1, see the following subsection.
(4) The unselected pins are pulled down with their internal resistors.
•
The demodulation input and S/PDIF through-output pins RXOUT1 and RXOUT2 data can be selected independently.
(1) The demodulation data is selected with RISEL[2:0].
(2) The RXOUT1 output data is selected with ROSEL[2:0].
(3) The RXOUT2 output data is selected with RXSEL[2:0].
•
•
It is possible to deselect all of RX0 to RX6 with RISEL[2:0] (RISEL[2:0]=111).
RXOUT1 and RXOUT2 can be muted with RXOSEL[2:0] and RXSEL[2:0], respectively. Muting is recommended to
reduce jitter when RXOUT1 and RXOUT2 are not used.
•
The data input state can be monitored with the RXMON setting. The status of each data input pin is stored in CCB
address 0xEA and output registers DO0 to DO7. Moreover, the latest information can be read with the
microcontroller by setting the interrupt processing command INDET. For details, see Chapter 12, Microcontroller
Interface.
•
The frequencies of input data that can be monitored with this setting is from 32kHz to 192kHz. The data detection
function applies to IEC60958 compatible S/PDIF data. The frequency of the clock supplied to XIN when RXMON is
set is limited to 24.576MHz. LC89058W-E does not run at any clock frequency other than 24.576MHz. Moreover,
since this function uses the XIN clock, the oscillation amplifier must be set in the continuous operation mode when
RXMON is set.
•
When the data input monitoring is specified, the input pins, except RX1pin and those which are selected for
demodulation, are pulled down. This is to preclude input-open when detecting no connection input pins. For the
peripheral circuit of the RX1 pin, see the following page.
No.A1056-27/64
LC89058W-E
10.2.3 S/PDIF input circuits (RX0 to RX6)
•
•
•
RX0, RX2, RX3, RX4, RX5, and RX6 can be received the data of 32kHz to 192kHz.
RX1 can be received up to 96kHz data.
If RX1 with a built-in amplifier is used as a coaxial input pin, malfunction may occur due to the influence from the
adjacent RX0 and RX2 input pins. To avoid the influences from those pins, fix RX0 and RX2 to "L". In addition, the
pull-down resistor is inserted after the coupling capacitor for the noise measures, when the signal is not connected
with RX1 is selected.
•
•
When RX1 is selected and the input signal to RX1 is always fixed to either "H" or "L" (Toslink etc), RX0 and RX2
processes are not required.
RX0, RX2, RX3, RX4, RX5, and RX6 are TTL input level compatible S/PDIF input pins with 5V-tolerance voltage.
LC89058W-E
RX0
Coaxial
RX1
RX2
≥470kΩ
RX3
RX4
Optical etc.
RX5
RX6
(a) Coaxial input circuit
LC89058W-E
Optical
RX0
RX1
RX2
RX3
RX4
Optical etc.
RX5
RX6
(b) Optical input circuit
Figure 10.7 S/PDIF Input Circuits
No.A1056-28/64
LC89058W-E
10.3 Serial Audio Data I/O
10.3.1 Output data format (RDATA)
•
The output format is set with OFDSEL.
The initial value of output format is I S.
2
•
•
Output data is output synchronized with the RLRCK edge immediately after the RERR output becomes "L".
L-ch
R-ch
RLRCK (O)
RBCK (O)
RDATA (O)
MSB
LSB
MSB
LSB
24bit
24bit
(0): I2S data output
L-ch
LSB
R-ch
LSB
RLRCK (O)
RBCK (O)
RDATA (O)
MSB
MSB
MSB
24bit
24bit
(1): MSB-first front-loading data output
Figure 10.8 Data Output Timing
No.A1056-29/64
LC89058W-E
10.3.2 Serial audio data input format (SDIN)
•
•
•
•
•
•
LC89058W-E is provided with a serial data input pin of SDIN.
The format of the serial audio data input to SDIN and the demodulation data output format must be identical.
2
The initial value of modulation data output format is I S.
The SDIN data to be input must be in synchronization with the RBCK and RLRCK clocks.
The data input from the SDIN pin is through-output to the RDATA pin.
The SDIN pin must be connected to GND when it is not used.
24bit
24bit
SDIN (I)
RLRCK (O)
RBCK (O)
MSB
MSB
LSB
LSB
MSB
MSB
LSB
LSB
L-ch
R-ch
RDATA (O)
(0): I2S data output
24bit
24bit
SDIN (I)
RLRCK (O)
RBCK (O)
MSB
MSB
LSB
L-ch
MSB
LSB
MSB
MSB
R-ch
RDATA (O)
LSB
MSB
LSB
(1): MSB-first front-loading data input
Figure 10.9 Serial Audio Data Input Timing
No.A1056-30/64
LC89058W-E
10.3.3 Output data switching (SDIN, RDATA)
•
RDATA outputs demodulation data when the PLL is locked, and outputs SDIN input data when the PLL is unlocked.
This output is automatically switched according to the PLL locked/unlocked status. For details, see the timing charts
below.
•
•
When SDIN input data is selected, switch to a clock source synchronized to the SDIN data.
With the RDTSTA setting, the SDIN input data is output to RDATA regardless of the locked/unlocked status of the
PLL.
•
•
With the RDTMUT setting, the RDATA output data can be also muted forcibly.
Even when the clock source is set to XIN with OCKSEL and RCKSEL, the PLL continues operating as long as the
PLL is not stopped with PLLOPR. At this time, the PLL status is continuously output from RERR unless error output
is forcibly set with RESTA. Moreover, the processed information can be read with the microcontroller interface
regardless of the PLL status.
PLL status
CKST
UNLOCK
LOCK
CKSTP=0
RERR
RDATA
SDIN data
LOCK
Muted
Demodulation data
(a): Lock-in stage
PLL status
CKST
UNLOCK
CKSTP=0
RERR
RDATA
Demodulation data
Muted
SDIN data
(b): Unlock stage
Figure 10.10 Timing Chart of RDATA Output Data Switching
No.A1056-31/64
LC89058W-E
10.3.4 Data block diagram (RX0 to RX6, RXOUT1, RXOUT2, RDATA, SDIN)
• Select the demodulated data and the SDIN input data with RDTSEL and RDTSTA, and mute processing can be
performed with RDTMUT.
• Moreover, GPIO0 input data can be selected with EXTSEL. Also, GPIO0 can be subject to mute processing with
EDTMUT. See Chapter 11 for the selector function for the general-purpose I/O pins (GPIO0 to GP1O3).
RX0
RX1
RX2
RX3
RX4
RX5
RX6
“ROSEL[2:0]”
“RXSEL[2:0]”
“ROSEL[2:0]=111”
“RXSEL[2:0]=111”
S/PDIF
S/PDIF
MUX
RXOUT1
RXOUT2
“RISEL[2:0]”
DIR
“RDTSEL”
“RDTSTA”
“RDTMUT”
“EXTSEL”
RDATA
SDIN
“EDTMUT”
GPIO3
Figure 10.11 Data System Diagram
10.3.5 Calculation of input data sampling frequency (MOUT)
• The input data sampling frequency is calculated using the XIN clock.
• In the mode where the oscillation amplifier automatically stops according to the lock status of the PLL, the input data
sampling frequency is calculated during the RERR error period and completed when the oscillation amplifier stops
with holding the value. Therefore, the value remains unchanged until the PLL becomes unlocked.
• If the oscillation amplifier is in a continuous operation mode, calculation is repeated constantly. Even if sampling
changes within the PLL capture range for input data whose channel status sampling information does not change, the
calculation results that follow the input data can be read.
• The calculation results can be readout via MOUT pin or with the microcontroller interface. Since the MOUT pin is
also used to generate the emphasis information, set the contents of the MOUT pin output by MOSEL. The fs
calculation output to the MOUT pin is limited. The FSSEL[1:0] sets the contents of the MOUT pin output.
Table 10.5: MOUT Pin Output Mode Settings
FSSEL1
FSSEL0
MOUT Pin H Output Conditions
0
0
1
1
0
1
0
1
When calculating 32kHz, 44.1kHz or 48kHz
When calculating 88.2kHz or 96kHz
When calculating 176.4kHz or 192kHz
When calculating 88.2kHz, 96kHz or higher
No.A1056-32/64
LC89058W-E
10.4 Error Output Processing
10.4.1 Lock error and data error output (RERR)
•
•
•
RERR outputs an error flag when a PLL lock error or a data error occurs.
It is possible to treat non-PCM data reception as an error by the RESEL setting.
The RERR output conditions are set with RESTA. Since the PLL status can be output at all times, the PLL status can
be always monitored, even when the clock source is XIN.
10.4.2 PLL lock error
• The PLL gets unlocked for input data that lost bi-phase modulation regularity, or input data for which preambles B, M,
and W cannot be detected. However, even if preambles B, M, and W are detected if the timing does not conform to
the IEC60958, the PLL get unlocked and processed. For example, period of preamble B is not every192 frames.
•
RERR turns to “H” when the PLL lock error occurs and returns to “L” when the data demodulation returns normal
and “H” is held for somewhere between 3ms to 144ms. This holding time is determined with the ERWT[1:0] setting.
The rising and falling edges of RERR are synchronized with RLRCK.
•
10.4.3 Input data parity error
•
•
Odd number of errors among parity bits in input data and input parity errors are detected.
If an input parity error occurs 9 or more times in succession, RERR turns to "H" indicating that the PLL is locked, and
after holding "H" for somewhere between 3ms and 144ms, it returns to "L".
The error flag output format can be selected with REDER, when an input parity error is output less than 8 times in
succession.
•
10.4.4 Other errors
•
Even if RERR turns to "L", the channel status bits of 24 to 27 (sampling frequency) are always fetched and the data of
the previous block is compared with the current data. Moreover, the input data sampling frequency is calculated from
the fs clock extracted from the input data, and the fs calculated value is compared in a same way as described above.
If any difference is detected in these data, RERR is instantly made "H" and the same processing as for PLL lock errors
is carried out.
•
The PLL causes a lock error when the fs changes as described above. However, in order to support sources with a
variable fs (for example a CD player with a variable pitch function), it is possible to set with FSERR not to output an
error flag unless fs changes exceeding the PLL capture range.
In the FSERR setting, when the PLL is locked, RERR is turned to “L” without reflecting the fs calculation result to the
error flag concerning input data within reception range by FSLIM [1:0].
Moreover, the data comparison at the channel status bits of 24 to 27 as described above is not performed.
If a setting which regard non-PCM data input as an error is made with RESEL, RERR turns to “H” when non-PCM
data input is detected. At this time, the PLL locked status and various output clocks are subject to the input data, but
the output data is muted.
•
No.A1056-33/64
LC89058W-E
10.4.5 Data processing upon occurrence of errors (lock error, parity error)
•
The data processing upon occurrence of an error is described below. If 8 or fewer input parity errors occur in
succession and transfer data is PCM audio data, the data is replaced by the one saved each in L-ch and R-ch in the
previous frame. However, if the transfer data is non-PCM data, the error data is output as it is.
Non-PCM data is the data of when bit 1 (audio sample word) of the channel status turns to "H" based on the data
detected prior to the occurrence of the input parity error.
•
•
•
Output data is muted when a PLL lock error occurs or a parity error occurs 9 or more times in succession.
As for the channel status output, the data of the previous block is held in 1-bit units when a parity error occur 8 or
fewer times in succession.
Table 10.6 Data Processing upon Error Occurrence
Data
Demodulation data
fs calculation result
Channel status
PLL Lock Error
Input Parity Error (a)
Input Parity Error (b)
Previous value data
Output
Input Parity Error (c)
Output
“L”
“L”
“L”
“L”
Output
“L”
Output
Previous value data
Previous value data
* Input parity error (a): If occurs 9 or more times in succession
* Input parity error (b): If occurs 8 or fewer times in succession, in case of audio data
* Input parity error (c): If occurs 8 or fewer times in succession, in case of non-PCM burst data
1occurrence
Input data
RERR
L-1 R-1 L-2 R-2 L-3 R-3 L-4 R-4 L-5 R-5 L-6 R-6 L-7 R-7 L-8 R-8
RLRCK
RDATA
L-0 R-0 L-1 R-0 L-2 R-2 L-2 R-2 L-2 R-2 L-2 R-2 L-2
R-ch
L-ch R-ch
9 times or more: Muting
Previous
Previous
value data
value data
Figure 10.12 Example of Data Processing upon Parity Error Occurrence
No.A1056-34/64
LC89058W-E
10.4.6 Processing during error recovery
•
•
When preambles B, M, and W are detected, PLL becomes locked and data demodulation begins.
Demodulation data is output from the RLRCK edge after RERR turns to "L".
RERR
Lock Signal
OK
RLRCK
RDATA
Data
3ms to 144ms
Output start from RWCK edge immediately after RERR is lowered
Figure 10.13 Data Processing When Data Demodulation Starts
________
10.5 Data Delimiter Bit 1 Output ( AUDIO)
____________
•
•
AUDIO outputs the channel status data delimiter bit 1 information.
Outputs bit 1 of the channel status that indicates whether the input bi-phase data is PCM audio data.
____________
AUDIO is immediately output upon detection of RERR even during "H" output period.
•
OR-output with IEC61937 or with the DTS-CD/LD detection flag is also possible with AOSEL.
____________
Table 10.7 AUDIO Output
______
AUDIO
Output Conditions
L
PCM audio data (CS bit 1 = "L")
Non-audio data (CS bit 1 = "H")
H
10.6 Emphasis Information Output (EMPHA)
• MOUT can output whether there is 50/15μs emphasis parameter for consumer by switching the contents of MOUT
output by MOSEL.
• MOUT is immediately output upon detection of RERR even during "H" output.
Table 10.8 MOUT Output
MOUT
Output Conditions
L
No pre-emphasis
H
50/15μs pre-emphasis
10.7 IEC61937, DTS-CD/LD Detection Flag Output
• A function to output
IEC61937 and DTS-CD/LD detection flag for non-PCM data is provided.
•
•
DTS-CD/LD is compatible with "14-bit format."
When bit 1 of channel status is non-PCM data, the IEC61937 sync signal is detected and detection flag is output. If bit
1 is PCM data, detection flag is not output.
•
•
The DTS-CD/LD sync signal detection is done based on the sync pattern and the base frequency. The sync pattern is
checked every 4096th frame, and the detection status is held until the sync pattern is no longer verified.
The IEC61937 and DTS-CD/LD detection flags can be readout with the microcontroller interface in addition to output
____________
to the AUDIO pin by AOSEL. When the UNPCM non-PCM signal output setting is selected through the INT output
contents setting, an interrupt signal is output from INT detecting an IEC61937 or DTS-CD/LD sync signal. Reading
output register from this information can see details of Non-PCM signal. This information is used to read out the
output register and identify the details of the non-PCM signal
•
The detection flags are cleared when fs is changed or when a PLL lock error or data error occurs.
No.A1056-35/64
LC89058W-E
11 Description of General-purpose I/O Function (GPIO0, GPIO1, GPIO2, GPIO3)
11.1 Initial Settings
• When setting
general-purpose I/Os for input, pull down INT with a 10kΩ resistors. When settings general-purpose
I/Os for output, pull up INT with a 10kΩ resistor. See Chapter 9 for INT pin settings.
If general-purpose I/Os are set to the output pin, the serial data input from the microcontroller interface is converted to
parallel data and output from of GPIO0, GPIO1, GPIO2, and GPIO3.
•
•
If general-purpose I/Os are set to the input pin, select one of the functions listed below with GPIOS.
(1) Store the parallel data input from the GPIO0, GPIO1, GPIO2, and GPIO3 in the internal register and readout the
contents of that register through the microcontroller interface (GPIOS=0).
(2) Configure a 2-to-1 (4 bits wide) selector that selects either the audio format data and clock that are input to the
GPIO0, GPIO1, GPIO2, and GPIO3 pins, or data and clock demodulated by the DIR block.
RMCK, RBCK, RLRCK, and RDATA are the outputs from the selector (GPIOS=1).
11.2 Output Function
•
The data output directed to the GPIO0, GPIO1, GPIO2, and GPIO3 are stored at CCB address 0xE8, command
address 10, input register bits DI12 to DI15, or register PI[3:0].
•
The data stored in PI[3:0] are transmitted out of the GPIO0, GPIO1, GPIO2, and GPIO3 pins.
11.3 Input Function
11.3.1 GPIOS=0
•
The data input to the GPIO0, GPIO1, GPIO2, and GPIO3 are taken into CCB address 0xEB, output register bits DO0
to DO3, or register PO[3:0].
•
The data must be readout by setting the interrupt source GPIO to INT or at an arbitrary timing. The way in which the
data is taken into the register depends on how it is readout.
11.3.1.1 GPIO=1 (using INT )
(1) XIN must always be given the specified clock and set in continuous operating mode (default).
(2) The data inputs to the GPIO0, GPIO1, GPIO2, and GPIO3 are taken into the register on a 24kHz clock.
(3) When the state of one of the data inputs changes, INT turns to “L” and suspends the data transfer to the register.
(4) The interrupt sources for CCB address 0xEA, output register DO14, and register OGPIO must be verified.
(5) INT turns “H” and the data is held in the register immediately when address 0xEA is readout.
(6) The read data from the PO[3:0] is transferred to the microcontroller. At the same time, the data in the register is
cleared.
(7) The contents of the register are updated if INT turns to “L” before P0[3:0] is readout.
11.3.1.2 GPIO=0 (not using INT )
(1) The data inputs to the GPIO0, GPIO1, GPIO2, and GPIO3 pins are taken in when the CCB address 0xEB is set.
(2) The data read from the PO[3:0] is transferred to the microcontroller. At the same time, the data in the register is
cleared.
No.A1056-36/64
LC89058W-E
11.3.2 GPIOS=1
•
The figure below shows the relationship between GPIO0, GPIO1, GPIO2, GPIO3 which are input to the selector and
the DIR block signal, and RMCK, RBCK, RLRCK, RDATA which are output from the selector and the control signal.
Lock judgment
4
“EXTSEL”
SDIN
ADC
24
4
4
4
XIN-MCK
XIN-BCK
XIN-LRCK
DIR
4
RMCK
RBCK
RLRCK
RDATA
16
17
20
21
PLL-MCK
PLL-BCK
PLL-LRCK
PLL-DATA
“EMCKP”
GPIO0
GPIO1
GPIO2
GPIO3
44
45
46
47
XM
radio
“EDTMUT”
Figure 11.1 Selector Configuration Diagram
Table 11.1 Selector I/O Signals
Input Pin or Input Signal
EXTSEL=0
Output pin
EXTSEL=1
PLL Lock State
PLL-MCK
PLL Unlock State
XIN-MCK
XIN-BCK
GPIO0 (pin 44)
GPIO1 (pin 45)
GPIO2 (pin 46)
GPIO3 (pin 47)
RMCK (pin 16)
RBCK (pin 17)
RLRCK (pin 20)
RDATA (pin 21)
PLL-BCK
PLL-LRCK
PLL-DATA
XIN-LRCK
SDIN
Note: The selector output generated when the PLL is locked can be changed to the XIN clock system by setting the
OCKSEL and RCSEL.
•
•
•
•
•
•
EXTSEL is enabled by setting GPIOS=1. When GPIOS=0 is set, the state of EXTSEL=0 is output from each pin.
The clock input to GPIO0 can be inverted by EMCKP and sent to RMCK.
The data to be input to GPIO3 must conform to the PLL-DATA or SDIN audio format.
The data input to GPIO3 can be muted by EDTMUT.
EMCKP and EDTMUT are enabled when GPIOS=1 is set.
The above settings are valid only when the master mode is set and must not be set when the slave mode is set.
No.A1056-37/64
LC89058W-E
_____
12. Microcontroller Interface (INT, CL, CE, DI, DO)
12.1 Description of Micr_o_c_o_ntroller Interface
12.1.1 Interrupt output (INT)
• Interrupts is output when a change has occurred in the PLL lock status or output data information.
______
• Interrupt output consists of the register for selecting the interrupt source, the INT pin that outputs that state transition,
and the registers that store the interrupt source data.
______
• Normally INT is held “H” and output “L” upon occurrence of an interrupt. Following “L” output, it is cleared and
returns to “H” immediately when the interrupt source output register is readout.
• The interrupt sources can be selected among the following items. Multiple sources can be selected at the same time
______
with the contents of CCB address 0xE8 and command address 8. INT outputs OR calculation result of the selected
interrupt sources.
______
...
INT output = (selected source 1) + (selected source 2) + + (selected source n)
Table 12.1 Interrupt Source Setting Contents
No.
1
Command Name
ERROR
INDET
Description
Output when RERR pin status has changed
2
Output when input data pin status has changed (subject to oscillation amplifier operation condition)
Output when input fs calculation result has changed. (subject to oscillation amplifier condition)
3
FSCHG
CSRNW
UNPCM
PCRNW
GPIO
4
Output when channel status data of first 48 bits have updated
______
5
Output when AUDIO pin status has changed
6
Output when burst preamble Pc has been updated
7
Output when the state of input data changes when the general-purpose I/O parallel input is set.
Output when emphasis information has changed
8
EMPF
• The contents of set interrupt source are saved in output registers DO8 to DO15 of CCB address 0xEA, when the
____________
source occurs. However, for the read registers for source items 1 and 5, the each status of the RERR and AUDIO pins
are output at the time of reading. Other data except for source items 1 and 5 are saved in the registers upon occurrence
of an interrupt source.
• Concerning source items 2 and 3, the oscillation amplifier clock is used. Therefore, if the status is monitored even
while the PLL is locked, the oscillation amplifier must be set to the continuous operation mode.
______
• Clearing INT at the same time of readout of an output register is carried out immediately after the output register
______
0xEA is set. However, INT is not cleared other than the 0xEA setting.
No.A1056-38/64
LC89058W-E
12.1.2 CCB interface
• The CCB interface is a Our original serial bus format based on LSB-first communication, but three-state is employed
instead of open-drain for the data output format of LC89058W-E.
• Data input/output is performed following CCB address input. The same CCB address cannot be used for both read and
write operation.
Table 12.2 Relationship between Register I/O Contents and CCB Addresses
Register I/O contents
Function setting data input
Input detection, interrupt output
fs data output
R/W
Write
Read
Read
Read
Read
CCB address
B0
B1
B2
B3
A0
A1
1
A2
1
A3
1
0xE8
0
0
0
1
0
0xEA
0
1
0
1
0
1
1
1
0xEB
1
1
0
1
0
1
1
1
CS data output
0xEC
0
0
1
1
0
1
1
1
Pc data output
0xED
1
0
1
1
0
1
1
1
12.1.3 Data write procedure
•
Input is performed in the following sequence: CCB addresses of A0 to A3 and B0 to B3, chip addresses of DI0 and
DI1, command addresses of DI4 to DI7, and data of DI8 to DI15. DI2 and DI3 are reserved for the system. So, DI2
and DI3 input must be doing "0".
•
For the chip addresses, DI0 corresponds to CAL (low-order), and DI1 to CAU (high-order). For details, see section 9.2.
12.1.4 Data read procedure
•
Read data is output from DO. DO is in the high impedance state when CE is "L", and begins outputting from the rising
edge of CE after output setting is established at the CCB address. DO then returns to the high impedance state at the
falling edge of CE.
•
If DO outputs are shared using multiple LC89058W-E units, it is possible to set the DO outputs of the LC89058W-E
units of which data is not to be read to be always in the high impedance state with DOEN. With this setting, only the
targeted outputs can be read.
12.1.5 Points to notices when normal H clock is used
•
The CCB interface uses CL of a normal L clock, and it is also possible to use CL of a normal H clock. However, input
the clock based on CCB microcontroller interface AC characteristics.
•
CL is lowered before CE is raised when data reads.
No.A1056-39/64
LC89058W-E
12.1.6 I/O timing
CE
CL
DI
⋅⋅⋅ ⋅⋅⋅
DI15
B0 B1 B2 B3 A0 A1 A2 A3
CAL
CAU DI2 DI3 DI4 DI5 DI6 DI7 DI8 DI9 DI10 DI1 DI2
DO
Hi-Z
Figure 12.1 Input Timing Chart (Normal L clock)
CE
CL
DI
⋅⋅⋅ ⋅⋅⋅
B0 B1 B2 B3 A0 A1 A2
A3
CAL CAU DI2 DI3 DI4 DI5 DI6 DI7 DI8 DI9 DI10 DI11 DI12
DI15
DO
Hi-Z
Figure 12.2 Input Timing Chart (Normal H clock)
(CL need not be lowered before CE is raised.)
CE
CL
DI
B0 B1 B2 B3 A0 A1 A2 A3
⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅
DO0 DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8
DOn
DO
Hi-Z
Figure 12.3 Output Timing Chart (Normal L clock)
CE
CL
DI
B0 B1 B2 B3 A0 A1 A2 A3
⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅ ⋅⋅⋅
DOn
DO0
DO1 DO2 DO3 DO4 DO5 DO6 DO7
DO
Hi-Z
Figure 12.4 Output Timing Chart (Normal H clock)
(CL is lowered before CE is raised, and DO0 need be read with port)
No.A1056-40/64
LC89058W-E
12.2 Write Data
12.2.1 List of write commands
•
A list of the write commands is shown below.
•
To write the commands shown in the following table, set the CCB address to 0xE8.
Table 12.3 Write Register Map
Add.
0
Setting Items
System setting 1
DI15
DI14
0
DI13
0
DI12
0
DI11
DI10
DI9
DOEN
0
DI8
SYSRST
MOSEL
0
TESTM
0
0
AOSEL
XMSEL0
XRSEL0
PSLRCK0
0
1
System setting 2
Master clock
0
0
FSLIM1
0
FSLIM0
PLLOPR
XRBCK0
XSBCK0
RDTSEL
ROSEL0
RBCKP
UNPCM
RESTA
PI0
RXMON
2
AMPOPR1
AMPOPR0
XRLRCK0
XSLRCK0
RDTMUT
ROSEL2
SBCKP
GPIO
XMSEL1
XINSEL
PRSEL1
PSBCK1
OCKSEL
RISEL1
0
3
R system output clock
S system output clock
Source switch
XRLRCK1
XRBCK1
XSBCK1
RDTSTA
ROSEL1
RLRCKP
PCRNW
FSERR
PI1
XRSEL1
PRSEL0
PSBCK0
0
4
XSLRCK1
PSLRCK1
5
0
0
6
Data I/O 1
0
0
RISEL2
0
RISEL0
OFDSEL
ERROR
RESEL
0
7
Output format
___
INTsource selection
SLRCKP
0
8
EMPF
CSRNW
FSCHG
0
INDET
REDER
0
9
RERR condition setting
General-purpose I/O
TEST
ERWT1
ERWT0
PI2
0
10
11
12
13
14
15
PI3
0
0
0
0
0
0
0
0
0
0
System setting 3
Data I/O 2
0
0
CKSTP
RXSEL1
0
RMCKP
RXSEL0
0
0
PLLDV1
EMCKP
PTOXW0
0
PLLDV0
EXTSEL
0
PLLACC
GPIOS
0
0
FSSEL1
0
RXSEL2
FSSEL0
0
EDTMUT
PTOXW1
0
PLL clock
TEST
0
0
0
0
Addr: Command address
• The shaded parts of DI8 to DI15 in the command area are reserved bits. Input must be doing "0".
• Command addresses 11 and 15 are reserved for testing purposes. Writing to these addresses is prohibited.
No.A1056-41/64
LC89058W-E
12.2.2 Details of write commands
CCB address: 0xE8; Command address: 0; System setting 1
DI7
0
DI6
0
DI5
0
DI4
0
DI3
0
DI2
0
DI1
DI0
CAU
CAL
DI15
DI14
0
DI13
0
DI12
0
DI11
0
DI10
0
DI9
DI8
TESTM
DOEN
SYSRST
SYSRST
DOEN
System reset
0: Don't reset (initial value)
1: Reset circuits other than command registers
DO pin output setting
0: Output (initial value)
1: Always high impedance state (read disabled)
TESTM
Test mode setting
0: Normal operation (initial value)
1: Enter test mode
• When reset by SYSRST is performed, RBCK outputs “L” and BLRCK outputs “H.”
CCB address: 0xE8; Command address: 1; System setting 2
DI7
0
DI6
0
DI5
DI4
DI3
DI2
DI1
DI0
0
1
0
0
CAU
CAL
DI15
0
DI14
0
DI13
DI12
DI11
DI10
DI9
0
DI8
FSLIM1
FSLIM0
RXMON
AOSEL
MOSEL
MOSEL
MOUT output contents setting
0: Output channel status emphasis information (initial value)
1: Output input data fs calculation results (output conditions are given by FSSEL[1:0].)
AOSEL
AUDIO output mode
0: Only output channel status bit 1 (initial value)
1: Output channel status bit 1, IEC61937 or DTS-CD/LD detection flag
RXMON
FSLIM[1:0]
Setting digital audio data (S/PDIF) input status monitoring
0: Don’t monitor S/PDIF input status (initial value).
1: Monitor S/PDIF input status
Setting of sampling frequency reception range for input digital signal
00: No limit (initial value)
01: fs≤96kHz (when exceeded, data is muted and clock is set to XIN system output)
10: fs≤48kHz (when exceeded, data is muted and clock is set to XIN system output)
11: Reserved
No.A1056-42/64
LC89058W-E
CCB address: 0xE8; Command address: 2; Master clock setting
DI7
0
DI6
0
DI5
DI4
DI3
DI2
DI1
DI0
1
0
0
0
CAU
CAL
DI15
DI14
DI13
0
DI12
DI11
DI10
DI9
DI8
0
AMPOPR1
AMPOPR0
PLLOPR
XMSEL1
XMSEL0
XINSEL
XINSEL
XIN input frequency setting
0: 12.288MHz (initial value)
1: 24.576MHz
XMSEL [1:0] XMCK output frequency setting
00: 1/1 of XIN input frequency (initial value)
01: 1/2 of XIN input frequency
10: 1/4 of XIN input frequency
11: Muted
PLLOPR
PLL (VCO) operation setting
0: Operate (initial value)
1: Stop
AMPOPR [1:0] Oscillation amplifier operation setting
00: Permanent continuous operation (initial value)
01: Reserved
10: Automatic stopping of oscillation amplifier while PLL is locked
11: Stop
• In order to replace LC89057W-VF4A-E, setting contents of the AMPOPR[1:0] are different from those of
LC89057W-VF4A-E.
No.A1056-43/64
LC89058W-E
CCB address: 0xE8; Command address: 3; R system output clock setting
DI7
0
DI6
DI5
DI4
DI3
DI2
DI1
DI0
0
1
1
0
0
CAU
CAL
DI15
DI14
DI13
DI12
DI11
DI10
DI9
DI8
XRLRCK1
XRLRCK0
XRBCK1
XRBCK0
XRSEL1
XRSEL0
PRSEL1
PRSEL0
PRSEL [1:0]
XRSEL [1:0]
Setting of RMCK output frequency while PLL is locked
(enabled when PLLACC is set to “0”)
00: 512fs×1/2 (256fs) (initial value)
01: 512fs×1/1 (512fs)
10: 512fs×1/4 (128fs)
11: Muted
Setting of RMCK output frequency during XIN source
00: 1/1 of XIN input frequency (initial value)
01: 1/2 of XIN input frequency
10: 1/4 of XIN input frequency
11: Muted
XRBCK [1:0] Setting of RBCK output frequency during XIN source
00: 3.072MHz output (RMCK≥6.144MHz) (initial value)
01: 6.144MHz output (RMCK≥12.288MHz)
10: 12.288MHz output (RMCK=24.576MHz)
11: Muted
XRLRCK [1:0]
Setting of RLRCK output frequency during XIN source
00: 48kHz output (initial value)
01: 96kHz output
10: 192kHz output
11: Muted
• Don’t do the setting to which RMCK=3.072MHz is output by XRSEL [1:0]=10(1/4 output) setting when
XIN=12.288MHz is input because it doesn't satisfy the output setting condition of RBCK and SBCK.
• Setting of XRBCK [1:0] relate to setting of RMCK output clock. RBCK output clock is set to become 1/2 or less of
RMCK output clock at XIN source.
No.A1056-44/64
LC89058W-E
CCB address: 0xE8; Command address: 4; S system output clock setting
DI7
0
DI6
DI5
DI4
DI3
DI2
DI1
DI0
1
0
0
0
0
CAU
CAL
DI15
DI14
DI13
DI12
DI11
DI10
DI9
DI8
XSLRCK1
XSLRCK0
XSBCK1
XSBCK0
PSLRCK1
PSLRCK0
PSBCK1
PSBCK0
PSBCK [1:0]
Setting of SBCK frequency while PLL is locked
00: 64fs output (initial value)
01: 128fs output
10: 32fs output
11: 16fs output
PSLRCK [1:0] Setting of SLRCK frequency while PLL is locked
00: fs output (initial value)
01: 2fs output
10: fs/2 output
11: fs/4 output
XSBCK [1:0]
Setting of SBCK frequency during XIN source
00: 3.072MHz output (RMCK≥6.144MHz) (initial value)
01: 6.144MHz output (RMCK≥12.288MHz)
10: 12.288MHz output (RMCK=24.576MHz)
11: Muted
XSLRCK [1:0] SLRCK output frequency setting during XIN source
00: 48kHz output (initial value)
01: 96kHz output
10: 192kHz output
11: Muted
• Setting of XSBCK [1:0] relate to setting of RMCK output clock. SBCK output clock is set to become 1/2 or less of
RMCK output clock at XIN source.
No.A1056-45/64
LC89058W-E
CCB address: 0xE8; Command address: 5; Clock source switching; RDATA output setting
DI7
0
DI6
DI5
DI4
DI3
DI2
DI1
DI0
1
0
1
0
0
CAU
CAL
DI15
0
DI14
DI13
DI12
DI11
0
DI10
0
DI9
DI8
0
RDTMUT
RDTSTA
RDTSEL
OCKSEL
OCKSEL
Clock source setting
0: Use XIN clock as source while PLL is unlocked (initial value)
1: Use XIN clock as source regardless of PLL status
RDTSEL
RDTSTA
RDTMUT
RDATA output setting while PLL is unlocked
0: Output SDIN data while PLL is unlocked (initial value)
1: Mute while PLL is unlocked
RDATA output setting
0: According to RDTSEL (initial value)
1: Output SDIN input data regardless of PLL status
RDATA mute setting
0: Output data selected with RDTSEL (initial value)
1: Muted
• When the oscillation amplifier is set to the permanent continuous operation mode with AMPOPR [1:0] or fs changes
are set not to be reflected to the error flag with FSERR, OCKSEL can switch the clock source while maintaining the
RERR status.
• The phase of R system clock and S system clock synchronize.
• To input data to SDIN, select a clock synchronized with the SDIN input data.
• The XIN source can be switched while maintaining the PLL locked status. However, since switching between clock
and data output can be set independently; it is recommended to select mute or SDIN data for the output data when
XIN source is switched.
• If the oscillation amplifier is set to stop automatically when the PLL gets locked, XIN source switching from the PLL
locked status disables the clock output. Be sure to set the oscillation amplifier to the continuous operation mode when
switching the clock source to the XIN source.
No.A1056-46/64
LC89058W-E
CCB address: 0xE8; Command address: 6; Data I/O setting 1
DI7
0
DI6
1
DI5
DI4
DI3
DI2
DI1
DI0
1
0
0
0
CAU
CAL
DI15
0
DI14
DI13
DI12
DI11
0
DI10
DI9
DI8
ROSEL2
ROSEL1
ROSEL0
RISEL2
RISEL1
RISEL0
RISEL [2:0]
Data demodulation input pin setting
000: RX0 selection (initial value)
001: RX1 selection
010: RX2 selection
011: RX3 selection
100: RX4 selection
101: RX5 selection
110: RX6 selection
111: None are selected (all inputs are connected to GND through pull-down resistors.)
ROSEL [2:0]
RXOUT1 output data setting
000: RX0 input data (initial value)
001: RX1 input data
010: RX2 input data
011: RX3 input data
100: RX4 input data
101: RX5 input data
110: RX6 input data
111: “L” fixed output
No.A1056-47/64
LC89058W-E
CCB address; 0xE8; Command address: 7; Data output format setting
DI7
0
DI6
1
DI5
DI4
DI3
DI2
DI1
DI0
1
1
0
0
CAU
CAL
DI15
DI14
DI13
DI12
DI11
0
DI10
0
DI9
0
DI8
SLRCKP
SBCKP
RLRCKP
RBCKP
OFDSEL
OFSEL
Audio data output format setting
0: I2S data output (initial value)
1: 24 bits, MSB first, left-justification output
RBCKP
RLRCKP
SBCKP
SLRCKP
RBCK output polarity setting
0: Falling RDATA data change (initial value)
1: Rising RDATA data change
RLRCK output polarity setting
0: "L" period: L-channel data; "H" period: R-channel data (initial value)
1: "L" period: R-channel data; "H" period: L-channel data
SBCK output polarity setting
0: Falling RDATA data change (initial value)
1: Rising RDATA data change
SLRCK output polarity setting
0: "L" period: L-channel data; "H" period: R-channel data (initial value)
1: "L" period: R-channel data; "H" period: L-channel data
No.A1056-48/64
LC89058W-E
______
CCB address: 0xE8; Command address: 8; INT output contents setting
DI7
1
DI6
DI5
DI4
DI3
DI2
DI1
DI0
0
0
0
0
0
CAU
CAL
DI15
DI14
DI13
DI12
DI11
DI10
DI9
DI8
EMPF
GPIO
PCRNW
UNPCM
CSRNW
FSCHG
INDET
ERROR
ERROR
INDET
FSCHG
CSRNW
UNPCM
PCRNW
GPIO
RERR signal output setting
0: Don't output (initial value)
1: Output RERR pin status change
Input data detection output setting
0: Don't output (initial value)
1: Output input data pin status change
Setting of updated flag output of PLL lock frequency calculation result
0: Don't output (initial value)
1: Output updated flag of PLL lock frequency calculation result
Output setting for updated flag of first 48-bit channel status data
0: Don't output (initial value)
1: Output update flag of first 48-bit channel status data
Output setting for change flag of non-PCM data detection
0: Don't output (initial value)
____________
1: Output AUDIO pin status change
Output setting for updated flag of burst preamble Pc
0: Don't output (initial value)
1: Output updated flag of burst preamble Pc
Input data updated flag output setting when general-purpose I/O parallel input is set (GPIOS=0)
0: Don't output (initial value)
1: Output input data updated flag
EMPF
Output setting of emphasis detection flag
0: Don't output (initial value)
1: Output emphasis detection flag
• The input data detection output setting functions when INDET=1 is set with the clock of 24.576MHz is supplied to
the terminal XIN (XINSEL=1) and digital data input state monitoring function (RXMON=1) made effective.
• The channel status update flag compares the first 48 bits of data of the previous block with those of the current block.
If these data are identical, it outputs a flag, considering the data has been updated.
• The burst preamble Pc update flag also compares the 16 bits of data of the previous block with those of the current
data. If they are identical, an update flag is output.
• The 4-bit input data updated flag when the general-purpose I/O parallel input is set, is output only when a change has
occurred in the sampling data with a clock of 24kHz.
No.A1056-49/64
LC89058W-E
CCB address: 0xE8, Command address: 9; RERR output setting
DI7
1
DI6
0
DI5
DI4
DI3
DI2
DI1
DI0
0
1
0
0
CAU
CAL
DI15
DI14
DI13
DI12
DI11
0
DI10
0
DI9
DI8
ERWT1
ERWT0
FSERR
RESTA
REDER
RESEL
RESEL
REDER
RESTA
RERR output contents setting
0: PLL lock error or data error (initial value)
1: PLL lock error or data error or non-PCM data
Setting of parity error flag output within 8 times in a row
0: Output only when non-PCM data is recognized (initial value)
1: Output only during sub-frame for which error was generated
RERR output condition setting
0: Output PLL status all the time (Output PLL status even during XIN source)
(initial status)
1: Forcibly output error (Set "H" to RERR forcibly)
FSERR
Setting of error flag output condition according to fs change
0: Reflect fs changes to error flag (initial value)
1: Don't reflect fs changes to error flag
ERWT [1:0]
Setting of RERR wait time after PLL is locked
00: Cancel error after preamble B is counted 3 (initial value)
01: Cancel error after preamble B is counted 24
10: Cancel error after preamble B is counted 12
11: Cancel error after preamble B is counted 6
_________
• Non-PCM data is identical to the detection data output to AUDIO.
• Output data is muted if an error occurs due to non-PCM data with RESEL.
• The RESTA setting is not reflected to the output pins of data and clock.
• For FSERR, the fs calculation result obtained while the oscillation amplifier is stopped is not reflected. In this case, fs
changes consist of only channel status fs information.
• ERWT[1:0] defines the interval of time for RERR to output error cancellation ("L") after PLL is locked. Since
demodulated audio data is output after RERR cancels an error, you need to change this setting if the situation that the
head of data is missing is a problem.
No.A1056-50/64
LC89058W-E
CCB address: 0xE8; Command address: 10; General-purpose I/O function
DI7
1
DI6
DI5
DI4
DI3
DI2
DI1
DI0
0
1
0
0
0
CAU
CAL
DI15
PI3
DI14
PI2
DI13
PI1
DI12
PI0
DI11
0
DI10
0
DI9
0
DI8
0
PI0
Contents of data output to the GPIO0 pin when the general-purpose I/O parallel output is set
0: L (initial value)
1: H
PI1
PI2
PI3
Contents of data output to the GPIO1 pin when the general-purpose I/O parallel output is set
0: L (initial value)
1: H
Contents of data output to the GPIO2 pin when the general-purpose I/O parallel output is set
0: L (initial value)
1: H
Contents of data output to the GPIO3 pin when the general-purpose I/O parallel output is set
0: L (initial value)
1: H
No.A1056-51/64
LC89058W-E
CCB address: 0xE8; Command address: 11; System settings 3
DI7
1
DI6
1
DI5
DI4
DI3
DI2
DI1
DI0
0
0
0
0
CAU
CAL
DI15
0
DI14
0
DI13
DI12
DI11
0
DI10
DI9
DI8
CKSTP
RMCKP
PLLDV1
PLLDV0
PLLACC
PLLACC
PLLDV0
PLLDV1
RMCKP
CKSTP
PLL clock lock frequency setting
0: Manual setting (initial value)
1: Automatic control (see 10.1.6.)
Set the PLL clock generated when 32kHz, 44.1kHz or 48kHz is received with PLLACC=1
0: 512fs output (initial value)
1: 256fs output
Set the PLL clock generated when 88.2kHz or 96kHz is received with PLLAC=1
0: 256fs output (initial value)
1: 512fs output
DIR block RMCK output setting
0: Normal output (initial value)
1: Inverted output
CKST output polarity setting
0: Normal high output (initial value)
1: Normal low output
No.A1056-52/64
LC89058W-E
CCB address: 0xE8; Command address: 12; Data I/O setting 2
DI7
1
DI6
1
DI5
DI4
DI3
DI2
DI1
DI0
0
1
0
0
CAU
CAL
DI15
0
DI14
DI13
DI12
DI11
DI10
DI9
DI8
RXSEL2
RXSEL1
RXSEL0
EDTMUT
EMCKP
EXTSEL
GPIOS
GPIOS
Setting of pins 44 to 47 input function (when INT pull-down is set)
0: General-purpose I/O parallel input (initial value)
I: Selector input
EXTSEL
EMCKP
RMCK, RBCK, RLRCK, and RDATA output setting
0: Output data and clock of DIR function (initial value).
1: Output input signals to GPIO0, GPIO1, GPIO2, GPIO3 (GPIOS=1)
GPIO0 output polarity setting (GPIOS=1)
0: Normal output (Initial value)
1: Inverted output
EDTMUT
RXSEL[2:0]
GPIO3 mute setting (GPIOS=1)
0: Normal output (initial value)
1: Muted
RXOUT2 output data setting
000: “L” fixed output (initial value)
001: RX0 input data
010: RX1 input data
011: RX2 input data
100: RX3 input data
101: RX4 input data
110: RX5 input data
111: RX6 input data
• GPIOS setting is needed when RMCK, RBCK, RLRCK, and RDATA output are changed with EXTSEL.
• RMCK, RBCK, RLRCK, and RDATA output don’t change even if it sets to EXTSEL=1 in the state of GPIOS=0.
No.A1056-53/64
LC89058W-E
CCB address: 0xE8; Command address: 13; PLL clock
DI7
1
DI6
1
DI5
DI4
DI3
DI2
DI1
DI0
1
0
0
0
CAU
CAL
DI15
DI14
DI13
0
DI12
0
DI11
DI10
DI9
0
DI8
0
FSSEL1
FSSEL0
PTOXW1
PTOXW0
PTOXW[1:0]
Setting of clock switch wait time
00: Clock switching after 2.67ms from when the PLL lock status is identified (initial value)
01: Clock switching after 1.33ms from when the PLL lock status is identified
10: Clock switching after 0.67ms from when the PLL lock status is identified
11: Clock switching after when the PLL lock status is identified
FSSEL[1:0]
MOUT output contents setting (output “L” when PLL unlock status or when a value other than
those listed below is calculated)
00: Output “H” when 32kHz/44.1kHz/48kHz is calculated (Initial value)
01: Output “H” when 64kHz/88.2kHz/96kHz is calculated
10: Output “H” when 128kHz/176.4kHz/192kHz is calculated
11: Output “H”when 64kHz/88.2kHz/96kHz or higher is calculated
No.A1056-54/64
LC89058W-E
12.3 Read Data
12.3.1 List of read commands
•
It is possible to read the following items.
− Interrupt data output
− Monitor output of digital data input status
− Input data output when general-purpose I/O parallel input mode is set
− Output of fs calculation result
− Output of first 48 bits of channel status
− Output of burst preamble Pc data
Table 12.4 Read Register Map
0xEA
RXDET0
RXDET1
RXDET2
RXDET3
RXDET4
RXDET5
RXDET6
0
0xEB
0xEC
0xED
DO0
DO1
PO0
CS bit0
CS bit1
CS bit2
CS bit3
CS bit4
CS bit5
CS bit6
CS bit7
CS bit8
CS bit9
CS bit10
CS bit11
CS bit12
CS bit13
CS bit14
CS bit15
CS bit16
CS bit17
CS bit18
CS bit19
CS bit20
CS bit21
CS bit22
CS bit23
CS bit24
CS bit25
Pc bit0
PO1
Pc bit1
DO2
PO2
Pc bit2
DO3
PO3
Pc bit3
DO4
FSC0
Pc bit4
DO5
FSC1
Pc bit5
DO6
FSC2
Pc bit6
DO7
FSC3
Pc bit7
DO8
OERROR
OINDET
OFSCHG
OCSRNW
OUNPCM
OPCRNW
OGPIO
OEMPF
CSBIT1
IEC1937
DTS51
DTSES
0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Pc bit8
DO9
Pc bit9
DO10
DO11
DO12
DO13
DO14
DO15
DO16
DO17
DO18
DO19
DO20
DO21
DO22
DO23
DO24
DO25
Pc bit10
Pc bit11
Pc bit12
Pc bit13
Pc bit14
Pc bit15
-
-
-
-
-
-
-
-
-
-
0
0
0
-
-
DO26
-
-
CS bit26
-
…
…
…
…
…
…
…
…
…
…
DO45
DO46
DO47
-
-
-
-
-
-
CS bit45
CS bit46
CS bit47
-
-
-
No.A1056-55/64
LC89058W-E
12.3.2 Read register 0xEA (S/PDIF input detection, interrupt flag) output
CCB address: 0xEA, Contents of read register output 1
DO7
0
DO6
DO5
DO4
DO3
DO2
DO1
DO0
RXDET6
RXDET5
RXDET4
RXDET3
RXDET2
RXDET1
RXDET0
RXDET0
RXDET1
RXDET2
RXDET3
RXDET4
RXDET5
RXDET6
RX0 input detection
0: No input data in RX0
1: Input data exist in RX0
RX1 input detection
0: No input data in RX1
1: Input data exist in RX1
RX2 input detection
0: No input data in RX2
1: Input data exist in RX2
RX3 input detection
0: No input data in RX3
1: Input data exist in RX3
RX4 input detection
0: No input data in RX4
1: Input data exist in RX4
RX5 input detection
0: No input data in RX5
1: Input data exist in RX5
RX6 input detection
0: No input data in RX6
1: Input data exist in RX6
• For readout of RXDET[10:0], RXMON must be set to "1" beforehand.
No.A1056-56/64
LC89058W-E
CCB address; 0xEA; Contents of read register output 2
DO15
DO14
DO13
DO12
DO11
DO10
DO9
DO8
OEMPF
OGPIO
OPCRNW
OUNPCM
OCSRNW
OFSCHG
OINDET
OERROR
OERROR
OINDET
OFSCHG
OCSRNW
OUNPCM
OPCRNW
OGPIO
RERR output (Output status during readout)
0: No transfer error while PLL is locked
1: Transfer error exists or PLL is unlocked
Status change of data input pin (clear after readout)
0: No change in status of data input pin
1: Change exists in status of data input pin
Result of updating input fs calculation (clear after readout)
0: No update of input fs calculation
1: Input fs calculation is updated
Update result of first 48 bits channel status (clear after readout)
0: Not updated
1: Updated
____________
AUDIO output (output of status during readout)
0: Non-PCM signal not detected
1: Non-PCM signal detected
Update result of burst preamble Pc (clear after readout)
0: Not updated
1: Updated
Update result of input date when the general-purpose I/O parallel input mode is set
(GPIOS=0) (clear after readout)
0: Not updated
1: Updated
OEMPF
Channel status emphasis detection (output of status during readout)
0: No pre-emphasis
1: 50/15μs pre-emphasis exists
____________
•
Concerning OERROR and OUNPCM, the status of RERR and AUDIO that are subject to RESEL setting are read
_______
regardless of the INToutput setting.
No.A1056-57/64
LC89058W-E
CCB address: 0xEA; Contents of read register output 3
DO23
0
DO22
0
DO21
DO20
DO19
DO18
DO17
DO16
0
0
DTSES
DTS51
IEC1937
CSBIT1
CSBIT1
IEC1937
DTS51
Channel status bit 1 detection
0: PCM
1: Non-PCM
IEC61937 burst preamble detection
0: Pa, Pb not detected
1: Pa, Pb detected
DTS-CD/LD 5.1 channel sync signal detection
0: DTS-CD/LD sync signal not detected
1: DTS-CD/LD sync signal detected
DTSES
DTS ES-CD/LD 6.1 channel sync signal detection
0: DTS ES-CD/LD sync signal not detected
1: DTS ES-CD/LD sync signal detected
No.A1056-58/64
LC89058W-E
12.3.3 Read register 0xEB (General-purpose I/O parallel input contents, fs calculation results) output
CCB address: 0xEB, Contents of read register output
DO7
DO6
DO5
DO4
DO3
DO2
DO1
PO1
DO0
PO0
FSC3
FSC2
FSC1
FSC0
PO3
PO2
PO0
Contents input to the GPIO0 pin when the general-purpose I/O parallel input mode is set
(GPIOS=0).
0: L
1: H
PO1
Contents input to the GPIO1 pin when the general-purpose I/O parallel input mode is set
(GPIOS=0).
0: L
1: H
PO2
Contents input to the GPIO2 pin when the general-purpose I/O parallel input mode is set
(GPIOS=0).
0: L
1: H
PO3
Contents input to the GPIO3 pin when the general-purpose I/O parallel input mode is set
(GPIOS=0).
0: L
1: H
FSC [3:0]
Input data fs calculation result
"xxxx": See code table.
Table 12.5 Code Table of Input fs Calculation Result (Ta = 25°C, AV
= DV
= 3.3 V)
DD
DD
FSC3
FSC2
FSC1
FSC0
Target Frequency
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Out of range
-
-
-
-
-
-
32kHz
44.1kHz
48kHz
64kHz
88.2kHz
96kHz
128kHz
176.4kHz
192kHz
No.A1056-59/64
LC89058W-E
12.3.4 Read register 0xEC (Readout of first 48 bits of channel status) output
• The first 48bits of channel status can be read.
• The readout channel status data is output with LSB first.
• For readout, set the CCB address to 0xEC.
• The channel status data cannot be updated after the CCB address is set.
• The relation between the read registers and the channel status data is shown below.
Table 12.6 Read Registers of First 48 bits of Channel Status
Register
DO0
Bit No.
Bit 0
Contents
Register
DO24
DO25
DO26
DO27
DO28
DO29
DO30
DO31
DO32
DO33
DO34
DO35
DO36
DO37
DO38
DO39
DO40
DO41
DO42
DO43
DO44
DO45
DO46
DO47
Bit No.
Bit 24
Bit 25
Bit 26
Bit 27
Bit 28
Bit 29
Bit 30
Bit 31
Bit 32
Bit 33
Bit 34
Bit 35
Bit 36
Bit 37
Bit 38
Bit 39
Bit 40
Bit 41
Bit 42
Bit 43
Bit 44
Bit 45
Bit 46
Bit 47
Contents
Application
Sampling frequency
DO1
Bit 1
Control
DO2
Bit 2
DO3
Bit 3
DO4
Bit 4
Clock accuracy
Not defined
DO5
Bit 5
DO6
Bit 6
Not defined
DO7
Bit 7
DO8
Bit 8
Category code
Word length
DO9
Bit 9
DO10
DO11
DO12
DO13
DO14
DO15
DO16
DO17
DO18
DO19
DO20
DO21
DO22
DO23
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
Bit 16
Bit 17
Bit 18
Bit 19
Bit 20
Bit 21
Bit 22
Bit 23
Not defined
Source number
Channel number
No.A1056-60/64
LC89058W-E
12.3.5 Read register 0xED (Burst preamble Pc data) output
• The burst preamble Pc data can be read with the demodulation function.
• The 16 bit-data of burst preamble Pc are output with LSB first.
• For readout, set the CCB address to OxED.
• The relation between the read register and burst preamble Pc data is shown below.
Table 12.7 Burst Preamble Pc Read Registers
Register
Bit No.
Contents
DO0
Bit 0
Data type
DO1
Bit 1
DO2
Bit 2
DO3
Bit 3
DO4
Bit 4
DO5
Bit 5
Reserved
DO6
Bit 6
DO7
Bit 7
Error
DO8
Bit 8
Data type dependent
Information
DO9
Bit 9
DO10
DO11
DO12
DO13
DO14
DO15
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
Bit stream number
No.A1056-61/64
LC89058W-E
12.3.6 Burst Preamble Pc Field
•
The burst preamble Pc field is shown below.
•
For the latest information, refer to official specifications.
Table 12.8 Burst Preamble Pc Field
Register
DO4 to 0
Value
Contents
0
NULL data
1
Dolby AC-3 data
Reserved
2
3
Pause
4
MPEG-1, layer 1 data
5
MPEG-1, layer 2, 3 data, or non-extended MPEG-2
Extended MPEG-2 data
Reserved
6
7
8
MPEG-2, layer 1, low sampling rate
MPEG-2, layer 2, 3, low sampling rate
Reserved
9
10
11
DTS type1
12
DTS type2
13
DTS type3
14
ATRAC
15
ATRACK2/3
16 to 26
Reserved
27
Reserved (MPEG-4, AAC data)
MPEG-2, AAC data
28
29 to 31
Reserved
DO6, 5
DO7
0
0
1
Reserved (set to "0")
Error flag indicating effective burst payload
Error flag indicating burst payload error
Data type dependent information
Bit stream number. (set to "0")
DO12 to 8
DO15 to 13
0
No.A1056-62/64
LC89058W-E
13 Application Example
12.288MHz
24.576MHz
Cx
Cx
Rd
Rf
Cc
Cc
Rp
Rp
Rp
Rp
Chip address
Chip address
Master/Slave
Expand/Selector
36 35 34 33 32 31 30 29 28 27 26 25
DO
SDIN
SLRCK
SBCK
RDATA
RLRCK
DV
DD
DGND
RBCK
RMCK
AGND
37
38
39
40
41
42
43
44
45
46
47
48
24
23
22
21
20
19
18
17
16
15
14
13
ADC
DAC
DSP
DI
CE
CL
M-computer
XMODE
DGND
LC89058W-E
SQFP48 (9X9)
Cc
Cc
Cc
DV
DD
GPIO0
GPIO1
GPIO2
HDMI
AV
GPIO3
RXOUT2
DD
LPF
1
2
3
4
5
6
7
8
9
10 11 12
R0
C0
C1
Coaxial Input
Ri
Ci
Optical Input
Cc
Cc
Table 13.1 Application Example
Element Symbol
Recommended Parameter
Application
Remarks
Cc
Rp
Cx
Rf
0.1μF
Power supply de-coupling
Function setting
Ceramic capacitor
10kΩ
Pull-down/pull-up resistor
1pF to 33pF
Quarts resonator load
Oscillation amplifier feedback
Oscillation amplifier current limit
Coaxial input DC cut
Coaxial input termination
PLL loop filter
Ceramic capacitor with NP0 characteristics
Ceramic capacitor
1MΩ
Rd
Ci
150Ω to 330Ω
0.1μF to 0.01μF
Ri
75Ω
∗∗
C0
C1
R0
(∗∗: See Section 10.1.1)
(∗∗: See Section 10.1.1)
(∗∗: See Section 10.1.1)
∗∗
PLL loop filter
∗∗
PLL loop filter
No.A1056-63/64
LC89058W-E
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitabilityof its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use
as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in
which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for
any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.A1056-64/64
相关型号：
©2020 ICPDF网 联系我们和版权申明