LC72720YVS-MPB-E [ONSEMI]
RDS/RBDS 单芯片信号处理器;型号: | LC72720YVS-MPB-E |
厂家: | ONSEMI |
描述: | RDS/RBDS 单芯片信号处理器 电信 光电二极管 电信集成电路 |
文件: | 总20页 (文件大小:1039K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ON Semiconductor
Is Now
To learn more about onsemi™, please visit our website at
www.onsemi.com
onsemi andꢀꢀꢀꢀꢀꢀꢀand other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or
subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi
product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without
notice. The information herein is provided “as-is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality,
or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws,
regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/
or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application
by customer’s technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized
for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for
implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and holdonsemi and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative
Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. Other names and brands may be claimed as the property of others.
LC72720YVS
RDS/RBDS Single-chip Signal
Processor IC
Overview
www.onsemi.com
The LC72720YVS is a single-chip system IC that implement the signal
processing required by the European Broadcasting Union RDS (Radio
Data System) standard and by the US NRSC (National Radio System
Committee) RBDS (Radio Broadcast Data System) standard. This IC
include band-pass filter, demodulator, synchronization, and error
correction circuits as well as data buffer RAM on chip and perform
effective error correction using a soft-decision error correction technique.
Functions
Band-pass filter : switched capacitor filter (SCF)
Demodulator : RDS data clock regeneration and demodulated data
reliability information
SSOP30 (275 mil)
Synchronization : Block synchronization detection
(with variable backward and forward protection conditions)
Error correction : Soft-decision/hard-decision error correction
Buffer RAM : Adequate for 24 blocks of data (about 500 ms) and flag
memory
Data I/O : CCB* interface (power on reset)
Features
Error correction capability improved by soft-decision error correction
The load on the control microprocessor can be reduced by storing
decoded data in the on-chip data buffer RAM.
Two synchronization detection circuits provide continuous and stable
detection of the synchronization.
Data can be read out starting with the backward-protection block data
after a synchronization reset.
Fully adjustment free
Specifications
Operating power-supply voltage : 3.0 to 3.6 V
Operating temperature
Package
: 40 to +85C
: SSOP30 (275 mil)
* Computer Control Bus (CCB) is an ON Semiconductor’s original bus format and
the bus addresses are controlled by ON Semiconductor.
ORDERING INFORMATION
See detailed ordering and shipping information on page 19 of this data sheet.
© Semiconductor Components Industries, LLC, 2017
July 2017 - Rev. 1
1
Publication Order Number :
LC72720YVS/D
LC72720YVS
Specifications
Absolute Maximum Ratings at Ta = 25C, Vssd = Vssa = 0 V
Parameter
Symbol
Vddmax
Vin1max
Vin2max
Vin3max
Vo1max
Vo2max
Vo3max
Io1max
Io2max
Io3max
Pdmax
Topr
Pin Name
Ratings
0.3 to +7.0
Unit
V
Maximum supply voltage
Vddd, Vdda
CL, DI, CE, SYR, T1, T2, T3, T4, T5, T6, T7, SYNC
V
0.3 to +7.0
0.3 to Vddd+0.3
0.3 to Vdda+0.3
0.3 to +7.0
0.3 to Vddd+0.3
0.3 to Vdda+0.3
+6.0
Maximum input voltage
Maximum output voltage
Maximum output current
XIN
V
MPXIN, CIN
V
DO, SYNC, RDS-ID, T3, T4, T5, T6, T7
XOUT
V
V
FLOUT
V
DO, T3, T4, T5, T6, T7
XOUT, FLOUT
SYNC, RDS-ID
(Ta 85C)
mA
mA
mA
mW
C
C
+3.0
+20.0
Allowable power dissipation
Operating temperature
Storage temperature
150
40 to +85
55 to +125
Tstg
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed,
damage may occur and reliability may be affected.
Allowable Operating Ranges at Ta = 40 to +85C, Vssd = Vssa = 0 V
Ratings
typ
Parameter
Symbol
Pin Name
Vddd, Vdda
Conditions
Unit
min
3.0
2.0
max
3.6
Vdd1
Vdd2
V
V
Supply voltage
Vddd
Serial data hold voltage
Input high-level
voltage
V
CL, DI, CE, SYR, T1, T2
0.7Vddd
0
6.5
V
V
IH
Input low-level
voltage
V
CL, DI, CE, SYR, T1, T2
0.3Vddd
IL
DO, SYNC, RDS-ID, T3,
T4, T5, T6, T7
V
Output voltage
6.5
50
V
O
V
mVrms
mVrms
f = 57 2 kHz
100% modulation
composite
IN1
MPXIN
XIN
V
Input amplitude
100
400
IN2
V
1500
mVrms
MHz
XIN
4.332
8.664
Guaranteed crystal
Oscillator
frequencies
CI 120 Ω (XS = 0)
CI 70 Ω (XS = 1)
XTAL
XIN, XOUT
MHz
ppm
Crystal oscillator
frequency
deviation
fo = 4.332 MHz,
8.664 MHz
TXtal
100
XIN, XOUT
0.75
0.75
0.75
Data setup time
Data hold time
tSU
tHD
DI, CL
DI, CL
s
s
s
Clock low level
time
tCL
CL
CL
Clock high level
time
0.75
s
tCH
0.75
0.75
0.75
CE wait time
tEL
tES
tEH
tCE
CE, CL
CE, CL
CE, CL
CE
s
s
s
ms
s
CE setup time
CE hold time
CE high-level time
20
Data latch change
time
1.15
tLC
tDC
tDH
Differs depending on the
value of the pull-up
resistor used.
0.46
0.46
s
s
DO,CL
DO,CE
Data output time
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended
Operating Ranges limits may affect device reliability.
www.onsemi.com
2
LC72720YVS
Electrical Characteristics at Ta = 40 to +85C, Vssd = Vssa = 0 V
Ratings
typ
Pin Name
MPXIN-Vssa
Parameter
Symbol
MPXIN
Conditions
Unit
min
max
Input resistance
R
f = 0 to 100 kHz
23
kΩ
Internal feedback
resistance
1.5
MΩ
Rf
XIN
Center frequency
fc
FLOUT
56.5
2.5
28
57.0
3.0
31
57.5
3.5
34
kHz
kHz
dB
3 dB band width
BW
3 dB
FLOUT
Gain
Gain
Att1
MPXIN-FLOUT
FLOUT
f = 57 kHz
f = 7 kHz
30
dB
Stop band
Attenuation
Att2
FLOUT
f < 45 kHz, f > 70 kHz
f < 20 kHz
40
dB
Att3
FLOUT
50
dB
Group delay
deviation
2.0
s
G-Delay
FLOUT
f = 57 1.2 kHz
Reference
voltage output
1.65
V
Vref
Vref
Vdda = 5.0 V
V
Hysteresis
HIS
CL, DI, CE, SYR, T1, T2
DO, T3, T4, T5, T6, T7
SYNC, RDS-ID
0.1Vddd
V
V
V
V
V
OL1
OL2
I = 2 mA
I = 8 mA
0.5
0.5
5.0
Output low-level
voltage
I
V = Vddd
I
IH1
IH2
IL1
IL2
CL, DI, CE, SYR, T1, T2
A
A
A
A
A
Input high-level
current
I
I
I
V = Vddd
I
0.9
0.9
4.0
5.0
4.0
5.0
XIN
V = 0 V
I
CL, DI, CE, SYR, T1, T2
XIN
Input low-level
current
V = 0 V
I
DO, SYNC, RDS-ID, T3,
T4, T5, T6, T7
Output off
leakage current
I
V
= 6.5 V
O
OFF
Current drain
Idd
Vddd, Vdda
Vddd = Vdda = 3.3 V
6
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be
indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
3
LC72720YVS
Package Dimensions
unit : mm
SSOP30 (275mil)
CASE 565AT
ISSUE A
SOLDERING FOOTPRINT*
(Unit: mm)
GENERIC
MARKING DIAGRAM*
XXXXXXXXXX
YMDDD
XXXXX = Specific Device Code
Y = Year
M = Month
0.65
0.32
DDD = Additional Traceability Data
NOTE: The measurements are not to guarantee but for reference only.
*This information is generic.
*For additional information on our Pb-Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
4
LC72720YVS
Pin Assignment
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
VREF
MPXIN
Vdda
SYR
1
2
CE
DI
3
NC
NC
4
Vssa
CL
5
FLOUT
CIN
DO
6
RDS-ID
7
NC
NC
LC72720YVS
8
T1
SYNC
9
T2
T7 (CORREC/ARI-ID/BE0)
10
11
12
13
14
15
T3 (RDCL)
NC
T6 (ERROR/57K/BE1)
NC
T4 (RDDA)
T5 (RSFT)
XOUT
Vssd
Vddd
XIN
Top view
Block Diagram
+3.3V
Vdda
+3.3V
Vddd
CIN
VREF
FLOUT
CLOCK
RECOVERY
(1187.5Hz)
-
PLL
(57kHz)
+
REFERENCE
VOLTAGE
Vssa
VREF
Vssd
57kHz
MPXIN
BPF
(SCF)
SMOOTHING
FILTER
ANTIALIASING
FILTER
DATA
DECODER
RDS-ID
DO
CL
DI
ERROR
CORRECTION
(SOFT DECISION)
SYNC
SYR
RAM
(24 BLOCK DATA)
SYNC/EC
CONTROLLER
CCB
CE
CLK (4.332MHz)
OSC/DIVIDER
MEMORY
CONTROL
T1
T2
T3 to T7
SYNC
DETECT-1
SYNC
DETECT-2
TEST
XIN
XOUT
www.onsemi.com
5
LC72720YVS
Pin Functions
I/O
Pin No.
Pin name
Function
Pin circuit
Vdda
Output
1
2
VREF
Reference voltage output (Vdda/2)
Vssa
Vdda
Input
MPXIN
Baseband (multiplexed) signal input
Vssa
Output
6
7
FLOUT
Subcarrier output (filter output)
Vdda
Input
CIN
Subcarrier input (comparator input)
Vssa
V
REF
3
5
Vdda
Vssa
Analog system power supply (+3.3 V)
Analog system ground
Vddd
Output
15
XOUT
Crystal oscillator output (4.332 / 8.664 MHz)
X
IN
16
XIN
Crystal oscillator input (external reference signal input)
Test input (This pin must always be connected to ground.)
X
Vssd
OUT
Input
9
T1
T2
S
Test input (standby control)
0:Normal operation, 1:Standby state
(crystal oscillator stopped)
Vssd
10
11
13
14
T3(RDCL)
T4(RDDA)
T5(RSFT)
Test I/O (RDS clock output)
Test I/O (RDS data output)
Test I/O (soft-decision control data output)
Vssd
I/O*
T6
Test I/O (error status, regenerated carrier, error block count)
20
21
(ERROR/57K/BE1)
T7
Test I/O
(CORREC/ARI-ID/BE0)
(error correction status, SK detection, error block count)
22
24
SYNC
Block synchronization detection output
RDS detection output
RDS-ID
Output
Input
Vssd
25
DO
Data output
26
28
29
30
17
18
CL
Clock input
Serial data interface (CCB)
S
DI
Data input
Chip enable
CE
Vssd
SYR
Vddd
Vssd
Synchronization and RAM address reset (active high)
Digital system power supply (+3.3 V)
Digital system ground
Note : * Normally function as an output pin. Used as an I/O pin in test mode, which is not available to user applications.
Pin 4, 8, 12, 19, 23, 27 are NC (NO CONNECT) Pins.
www.onsemi.com
6
LC72720YVS
CCB output data format
1. Each block of output data consists of 32 bits (4 bytes), of which 2 bytes are RDS data and 2 bytes are flag data.
2. Any number of 32-bits output data blocks can be output consecutively.
3. When there is no data that can be read out in the internal memory, the system outputs blocks of all-zero data
consecutively.
4. If data readout is interrupted, the next read operation starts with the 32-bit data block whose readout was interrupted.
However, if only the last bit is remaining to be read, it will not be possible to re-read that whole block.
5. The check bits (10 bits) are not output.
6. The data valid (OWD) must not be referred to.
7. When the first leading bits are not “1010”, the read in data is in invalid, and read operation is cancelled.
CCB address 6C
B
0
B
1
B
2
B
3
A
0
A
1
A
2
A
3
DI
0
0
1
1
0
1
1
0
Last bit
Output data / first bit
O
B
D
R
F
1
R
F
0
A
R
I
S
Y
C
D
1
5
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
B
1
B
0
R
E
E
2
E
1
E
0
D D D D D D D D D D
1
0
1
0
W
DO
2
9
8
7
6
5
4
3
2
1
0
(8) RDS data
(7) Error information flags
(6) Synchronization established flag
(5) ARI(SK) detection flag
(4) RAM data remaining flags
(3) Consecutive RAM read out possible flag
(2) Offset word information flags
(1) Offset word detection flag
Fixed pattern (1010)
(1) Offset word detection flag (1 bit) : OWD
OWD
Offset word detection
Detected
1
0
Not detected (protection function operating)
(2) Offset word information flag (3 bit) : B0 to B2
B
2
B
1
B
0
Offset word
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
A
B
C
C’
D
E
Unused
Unused
www.onsemi.com
7
LC72720YVS
(3) Consecutive RAM read out possible flag (1 bit) : RE
RE
1
RAM data information
The next data to be read out is in RAM
0
This data item is the last item in RAM, ant the next data is not present.
(4) RAM data remaining flag (2 bits) : RF0,RF1
RF1
RF0
Remaining data in RAM (number of blocks)
0
0
1
1
0
1
0
1
1 to 7
8 to 15
16 to 23
24
Caution : This value is only meaningful when RE is 1. When RE is 0, there is no data in RAM, even if RF is 00.
If a synchronization reset was applied using SYR, then the backward protection block data that was written to memory
is also counted in this value.
(5) ARI(SK) detection flag (1 bit) : ARI
ARI
1
SK signal
Detected
0
Not detected
(6) Synchronization established flag (1 bit) : SYC
SYC
Synchronization detection
Synchronized
1
0
Not synchronized
Caution : This flag indicates the synchronization state of the circuit at the point when the data block being output was received.
On the other hand, the SYNC pin (pin18) output indicates the current synchronization state of the circuit.
(7) Error information flags (3 bits) : E0 to E2
E
2
E
1
E
0
Number of bits corrected
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0 (no errors)
1
2
3
4
5
Correction not possible
Unused
Caution : If the number of errors exceeds the value of the EC0 to EC2 setting (see the section on the CCB input format),
the error information flags will be set to the “Correction not possible” value.
(8) RDS data (16bits) : D0 to D15
This data is output with the MSB first ant the LSB last.
Caution : When error correction was not possible, the input data is output without change.
www.onsemi.com
8
LC72720YVS
CCB Input data format
IN1 data, first bit
[1] CCB address 6A
B B
B
2
B
3
A
0
A A
A
3
F F F F
S S S S
0 1 2 3
S
Y
R
O E E E
W C C C
E E C
C C T
B
S
0
1
1
2
DI
E
0 1
2
3 4
0
0
1
0
1
0
1
1
0
(11) Circuit control
(5) Error correction method setting
(4) RAM write control
(3) Synchronization and RAM address reset
(2) Synchronization detection method setting
(1) Synchronization protection method setting
IN2 data, first bit
P P
[2] CCB address 6B
B B
B
2
B
3
A A A
A
3
C
T
1
P P P
T T T
T T T T
S S S S
0 1 2 3
X
S
R
0
1
0
1
2
L
0
L
1
DI
M
0 1
2
1
1
0
1
0
1
1
0
(10) Test mode settings
(9) Output pin settings
(8) RDS/RBDS selection
(7) Demodulation circuit phase control
(6) Crystal oscillator frequency selection
(11) Circuit control
Caution : The bits labeled with an asterisk must be set to 0.
(1) Synchronization protection (forward protection) method setting (4 bits) : FS0 to FS3
FS3 = 0 : If offset words in the correct order could not be detected continuously during the number of blocks
specified by FS0 to FS2, take that to be a lost synchronization sate.
FS3 = 1 : If blocks with uncorrectable errors were received consecutively during the number of blocks specified by
FS0 to FS2, take that to be a lost synchronization state.
F
S
0
F
S
1
F
S
2
Condition for detecting lost synchronization
0
1
0
1
0
1
0
1
0
0
1
1
0
0
1
1
0
0
0
0
1
1
1
1
If 3 consecutive blocks matching the FS3 condition are received.
If 4 consecutive blocks matching the FS3 condition are received.
If 5 consecutive blocks matching the FS3 condition are received.
If 6 consecutive blocks matching the FS3 condition are received.
If 8 consecutive blocks matching the FS3 condition are received.
If 10 consecutive blocks matching the FS3 condition are received.
If 12 consecutive blocks matching the FS3 condition are received.
If 16 consecutive blocks matching the FS3 condition are received.
Initial value : FS0 = 0, FS1 = 1, FS2 = 0, FS3 = 0
www.onsemi.com
9
LC72720YVS
(2) Synchronization detection method setting (1 bit) : BS
BS
0
Synchronization detection conditions
If during 3 blocks, 2 blocks of offset words were detected in the correct order.
If the offset words were detected in the correct order in 2 consecutive blocks.
1
Initial value : BS = 0
(3) Synchronization and RAM address reset (1 bit) : SYR
SYR
0
Synchronization detection circuit
Normal operation (reset cleared)
RAM
Normal write (See the description of the OWE bit)
After the reset is cleared, start writing from the data prior
to the establishment of synchronization, i.e. the data in
backward protection.
Forced to the unsynchronized state
(synchronization reset)
1
Initial value : SYR = 0
Caution : 1. To apply a synchronization reset, set SYR to 1 temporarily using CCB, and then set it back to 0 again using CCB.
The circuit will start synchronization capture operation at the point SYR is set to 0.
2. The SYR pin (pin30) also provides an identical reset control operation. Applications can use either method.
However, the control method that is not used must be set to 0 at all times.
Any pulse with a width of over 250 ns will suffice.
3. A reset must be applied immediately after the reception channel is changed.
If a reset is not applied, reception data from the previous channel may remain in on-chip memory.
4. Data read out after a synchronization reset is read out starting with the backward protection block data preceding
the establishment of synchronization.
(4) RAM write control (1 bit) : OWE
OWE
RAM write conditions
0
1
Only data for which synchronization had been established is written.
Data for which synchronization not has been established (unsynchronized data) is also
written. (However, this applies when SYR = 0.)
Initial value : OWE = 0
(5) Error correction method setting (5 bits) : EC0 to EC4
E
C
0
E
C
1
E
C
2
E
C
3
E
C
4
Number of bits corrected
Soft-decision setting
0
0
0
0
1
0
1
0
0
1
1
0 (error detection only)
1 or fewer bits
2 or fewer bits
3 or fewer bits
4 or fewer bits
5 or fewer bits
Illegal value
MODE0 Hard decision
MODE1 Soft decision A
MODE2 Soft decision B
Illegal value
1
0
1
0
1
0
1
0
1
1
0
0
1
1
0
0
0
1
1
1
1
Illegal value
Initial values : EC0 = 0, EC1 = 1, EC2 = 0, EC3 = 0, EC4 = 1
Caution : 1. If soft-decision A or soft-decision B is specified, soft-decision control will be performed even if the number
of bits corrected is set to 0 (error detection only). With these settings, data will be output for blocks with no errors.
2. As opposed to soft-decision B, the soft-decision A setting suppresses soft decision error correction.
www.onsemi.com
10
LC72720YVS
(6) Crystal oscillator frequency selection (1 bit) : XS
XS = 0 : 4.332 MHz (Initial value : XS = 0)
XS = 1 : 8.664 MHz
(7) Demodulation circuit phase control (2 bits) : PL0, PL1
PL0
0
PL1
0/1
0
Demodulation circuit phase control
Normal operation when ARI presence or absence is unclear.
If the circuit determines that the ARI signal is absent : 90 phase
If the circuit determines that the ARI signal is present : 0 phase
1
1
Initial values : PL0 = 0, PL1 = 1
Caution : 1. When PL0 is 0 (normal operation), the IC detects the presence or absence of the ARI signal and reproduces
the RDS data by automatically controlling the demodulation phase with respect to the reproduced carrier.
However, the initial phase following a synchronization reset is set by PL1.
2. If PL0 is set to 1, the demodulation circuit phase is locked according to the PL1 setting at either 90 (PL1 = 0) or
0 (PL1 = 1), allowing RDS data to be reproduced. When ARI is not present, PL1 should be set to 0, since the
RDS data is reproduced by detecting at a phase of 90 with respect to the reproduced carrier. When ARI is present,
PL1 should be set to 1, since detection is at 0. In cases where the ARI presence is known in advance, more stable
reproduction can be achieved by fixing the demodulation phase in this manner.
(8) RDS/RBDS(MMBS) selection (1 bit) : RM
RM
0
RBDS
None
Decoding method
Only RDS data is decoded correctly (Offset word E is not detected.)
RDS and MMBS data is decoded correctly (Offset word E is also detected.)
1
Provided
Initial value : RM=0
(9) Output pin settings (3 bits) : PT0 to PT2
These bits control the T3, T4, T5, T6, T7, SYNC, and RDS-ID pins
T3
T4
T5
T6
T7
P
T
0
P
T
1
P
T
2
MODE
RDCL RDDA RSFT ERROR 57K BE1 CORREC ARI-ID BE0
0
1
2
3
4
5
6
7
0
1
0
1
0
1
0
1
0
0
1
1
0
0
1
1
0
0
0
0
1
1
1
1
: open, , : Output enabled ( = reverse polarity)
Initial value : PT0 = 1, PT1 = 1, PT2 = 0 (Mode 3)
Caution : 1. When PT2 is set to 1, the polarity of the T3(RDCL), T6(ERROR/57K), T7(CORREC/ARI-ID), SYNC,
and RDS-ID pins changes to active high.
2. The output pins (T3 to T7, SYNC, and RDS-ID) are all open-drain pins, and require external pull-up resistors
to output data.
www.onsemi.com
11
LC72720YVS
Item
Pin T3 (RDCL)
PT2 = 0
PT2 = 1
Data(RDDA and RSFT) changes on this pin’s rising edge
Data(RDDA and RSFT) changes on this pin’s falling edge
Mode2 (PT2 = 0)
No SK
Pin T7 (ARI-ID)
High (1)
SK present
Low (0)
Mode3 (PT2 = 0)
Correction not possible
Errors corrected
No errors
Pin T6 (ERROR)
Low (0)
Pin T7 (CORREC)
Low (0)
High (1)
High (1)
Low (0)
High (1)
Mode = 4
Number of error blocks (B)
B=0
Pin T6 (BE1)
Pin T7 (BE0)
Low (0)
Low (0)
High (1)
High (1)
Low (0)
High (1)
Low (0)
High (1)
1 B 20
20 B 40
40 B 48
These pins indicate the number of blocks in a set of 48 blocks that had errors before correction.
The output polarity of these pins is fixed at the values listed in the table.
Mode (PT2 = 0)
0 to 2
The SYNC pin
When synchronized : Low (0), When unsynchronized: High (1)
When synchronized : Goes high for a fixed period (421 s) at the
start of a block and then goes low.
3
When unsynchronized : High (1)
Caution : The output indicates the synchronization state for the previous block.
When PT2 = 0
The RDS-ID pin
No RDS
High (1)
Low (0)
RDS present
(10) Test mode settings (4bits) : TS0 to TS3
Initial values : TS0 = 0, TS1 = 0, TS2 = 0, TS3 = 0
(Applications must set these bits to the above values.)
Notes : The T1 and T2 pins (pins 9 and 10) are related to test mode as follows.
Pin T1
Pin T2
IC operation
Normal operating mode
Notes
0
0
1
0
1
These states are user settable
Standby mode (crystal oscillator stopped)
0/1
IC test mode
Users cannot use this state
The T1 pin must be tied to V (0V).
SS
(11) Circuit control (2 bits) : CT0 and CT1
Item
Control
When set to 1, soft-decision control data (RSFT) is
easier to generate.
When set to 1, the RDS-ID detection conditions are
made more restrictive.
CT0
CT1
RSFT control
RDS-ID detection condition
Initial value : CT0 = 0, CT1 = 0
www.onsemi.com
12
LC72720YVS
RDCL / RDDA / RSFT and ERROR / CORREC / SYNC output timing
(1) Timing 1
421 μs
421 μs 421 μs
Tp1
RDCL output
RDDA output
RSFT output
842 μs
Note : When PT2 = 0, RDDA and RSFT must be acquired on the falling edge of RDCL.
(2) Timing 2 (mode 3, PT2 = 0)
Sync OK
Input data
Sync NG Sync OK Sync OK
Sync OK Sync OK Sync NG Sync NG
No
No
Data
corrected
Data
corrected
Error crrection
SYNC output
ERROR output
errors
errors
Tp1
Tp1
CORREC output
www.onsemi.com
13
LC72720YVS
Serial Data Input and Output Methods
Data is input and output using the CCB (Computer Control Bus), which is Our audio IC serial bus format.
This IC adopts an 8-bit address CCB format.
(LSB)
Address
(MSB)
Comment
I/O mode
B0 B1 B2 B3 A0 A1 A2 A3
Control data input mode, also referred to as
“ serial data input ” mode.
16bit data input mode
[1]
[2]
IN1 (6A)
IN2 (6B)
0
1
1
1
0
0
1
1
0
0
1
1
1
1
0
0
Data output mode
The data for multiple blocks can be
output sequentially in this mode.
[3]
OUT (6C)
0
0
1
1
0
1
1
0
I/O mode determined
CE
1
2
CL
B0
B1
B2
B3
A0
A1
A2
A3
DI
First Data IN1/2
1
2
DO
First Data OUT
First Data OUT
1
2
For the CL normal high state
For the CL normal low state
www.onsemi.com
14
LC72720YVS
(1) Serial data input (IN1 / IN2)
, t , t , t , t 0.75 s t
t
1.15 s t 20 ms
CE
SU HD EL ES EH LC
CL : Normal high
t
CE
t
t
t
EL
ES
EH
CE
CL
t
t
SU
HD
FS0 FS1 FS2 FS3
EC3 EC4 CT0
TS0 TS1 TS2
0
TS3
DI
B0 B1 B2 B3 A0 A1 A2
A3
CT1
0
0
0
t
LC
Internal data
CL : Normal low
t
CE
t
t
t
EL
ES
EH
CE
CL
t
t
SU
HD
B0 B1 B2 B3 A0 A1 A2 A3
FS0
CT1
FS1 FS2 FS3
EC3 EC4 CT0
TS0 TS1 TS2
0
TS3
DI
0
0
0
t
LC
Internal data
(2) Serial data output (OUT)
, t , t , t , t
t
0.75 s t , t
DC DH
0.46 s t
20 ms
SU HD EL ES EH
CE
CL : Normal high
t
CE
t
t
t
EH
EL
ES
CE
CL
t
t
SU
HD
B0 B1 B2 B3 A0 A1 A2
A3
DI
t
t
t
DC
DC
DH
D3 D2 D1 D0
1
0
1
0
DO
CL : Normal low
t
CE
t
t
t
EH
EL
ES
CE
CL
t
t
SU
HD
B0 B1 B2 B3 A0 A1 A2
A3
DI
t
t
t
DC
DC
DH
D3 D2 D1 D0
1
0
1
0
DO
Cautions : 1. Since the DO pin is an n-channel open-drain output, the transition times (t , t ) will differ with the value of
DC DH
the pull-up resistor used.
2. The CE, CL, DI, and DO pins can be connected to the corresponding pins on other ICs that use the CCB interface.
(However, we recommend connecting the DO and CE pins separately if the number of available microcontroller
ports allows it.)
3. Serial data I/O becomes possible after the crystal oscillator starts oscillation.
www.onsemi.com
15
LC72720YVS
(3) Serial data timing
CL : Normal high
t
CE
V
IH
CE
V
IL
t
t
CH
CL
V
V
V
V
IH
IL
V
IH
CL
IL
IH
t
t
t
EH
EL
ES
V
V
V
IH
IH
IL
DI
V
IL
t
t
t
t
SU
HD
DC
DH
DO
t
LC
Internal data latch
New
Old
CL : Normal low
t
CE
V
IH
CE
V
IL
t
t
CL
CH
V
V
IH
IL
t
EH
V
IH
CL
V
V
V
IL
IL
IL
t
t
ES
EL
V
V
IH
IH
DI
V
V
IL
IL
t
t
t
t
t
DH
SU
HD
DC
DC
DO
t
LC
Old
New
Internal data latch
Parameter
Data setup time
Data hold time
Symbol
Conditions
min
0.75
0.75
0.75
0.75
0.75
0.75
0.75
typ
max
Unit
t
SU
DI, CL
DI, CL
CL
s
s
s
s
s
s
s
ms
s
s
s
t
HD
t
Clock low level time
Clock high level time
CE wait time
CL
t
CH
CL
t
EL
CE, CL
CE, CL
CE, CL
CE
t
CE setup time
ES
t
CE hold time
EH
t
t
t
CE high level time
CE
LC
20
Data latch transition time
1.15
0.46
0.46
DC
DH
DO, CL
DO, CE
Differs with the value of the pull-up
resistor used.
Data output time
t
www.onsemi.com
16
LC72720YVS
DO pin operation
This IC incorporates a RAM data buffer that can hold up to 24 blocks of data. At the point when one block of data is
written to this RAM, the IC issues a read request by switching the DO pin from high to low.
The DO pin always goes high for a fixed period (Tdo = 265 s) after a readout and CE goes low. When all the data
in the data buffer has been read out, the DO pin is held in the high state until a new block of data has been written to
the RAM. If there is data that has not yet been read remaining in the data buffer, the DO pin goes low after the Tdo
time has elapsed.
After a synchronization reset, the DO pin is held high until synchronization is established. It goes low at the point
the IC synchronizes.
When the DO pin is high following the 265 s period (Tdo) after data is read out.
Here, the buffer is in the empty state, i.e. the state where new data has not been written. After this, when the DO
pin goes low, applications are guaranteed to be able to read out that data without it being overwritten by new data
if they start a readout operation within 480 ms of DO going low.
Tdo
CE pin
T
DO pin
New data
(Last data)-1
Last data
DO check (Tdo < T)
When DO goes low 265 s after data is read out
Here, there is data that has not been read out remaining in the data buffer. In this case, applications are
guaranteed to be able to read out that data without it being overwritten by new data if they start a readout
operation within 20 ms of DO going low. (Note that this is the worst case condition.)
Tdo
CE pin
T
DO pin
(Last data)-2
(Last data)-1
Last data
DO check (Tdo < T)
Notes :
1. Although an application can determine whether or not there is data remaining in the buffer by checking the DO level
with the above timing, checking the RE and RF flags in the serial data is a preferable method.
2. Applications are not limited to reading out one block of data at a time, but rather can read out multiple blocks of data
continuously as described above. When using this method, if an application references the RE and RF flags in the
data while reading out data, it can determine the amount of data remaining. However, the length of the period for data
readout (the period the CE pin remains high) must be kept under 20 ms.
3. If the DO pin is shared with other ICs that use the CCB interface, the application must identify which IC issued the
readout request. One method is to read out data from the LC72720YVS and either check whether meaningful data
has been read (if the LC72720YVS is not requesting a read, data consisting of all zeros will be read out) or check
whether the DO level goes low within the 256 s following the completion of the read (if the DO pin goes low, then
the request was from another IC).
www.onsemi.com
17
LC72720YVS
Sample Application Circuit
SYR
1
2
30
29
28
26
25
24
22
21
20
18
17
16
10 μF +
Vssa
V
SYR
CE
REF
Vssd
MPXIN
Vdda
MPXIN
Vdda
Vssa
FLOUT
CIN
T1
CE
330 pF
3
DI
DI
0.1 μF
5
CL
CL
Vddd
10 kΩ
Vddd
10 kΩ
Vddd
10 kΩ
Vssa
6
DO
DO
560 pF
100 kΩ
7
RDS-ID
SYNC
T7
RDS-ID
SYNC
9
10
11
13
14
15
T2
NC
NC
Vssd
NC
T3
T6
Vssd
0.1 μF
NC
NC
T4
Vssd
Vddd
Vddd
T5
X
X
IN
OUT
4.332 MHz
16 pF
16 pF
Vssd
Vssd
Caution : 1. Determine the value of the DO pin pull-up resistor based on the required serial data transfer speed.
2. A 100 k bias resistor must be connected between the CIN pin and the VREF pin. Note that this resistor
is planned to be included internally to the IC in later versions of this product.
3. If the SYR pin is unused, it must be connected to ground.
www.onsemi.com
18
LC72720YVS
ORDERING INFORMATION
Device
Package
Shipping (Qty / Packing)
48 / Fan-Fold
SSOP30 (275 mil)
(Pb-Free)
LC72720YVS-MPB-E
LC72720YVS-TLM-E
SSOP30 (275 mil)
(Pb-Free)
1000 / Tape & Reel
† For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel
Packaging Specifications Brochure, BRD8011/D. http://www.onsemi.com/pub_link/Collateral/BRD8011-D.PDF
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries
in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other
intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON
Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or
use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is
responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or
standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters,
including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its
patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support
systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for
implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall
indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an
Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
www.onsemi.com
19
相关型号:
©2020 ICPDF网 联系我们和版权申明