6N135SD [ONSEMI]
Logic IC Output Optocoupler;
| 型号： | 6N135SD |
| 厂家： | 
ONSEMI |
| 描述： | Logic IC Output Optocoupler 输出元件 光电 |
| 文件： | 总12页 (文件大小：633K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
DUAL-CHANNEL: HCPL-2530
6N136
HCPL-2531
HCPL-2503
HCPL-4502
PACKAGE
SCHEMATIC
VCC
8
+
VCC
1
N/C
1
8
VF1
_
8
V01
7
VB
2
+
2
3
4
7
6
5
1
VF
_
_
V02
3
6
5
VO
VF2
GND
N/C
GND
+
4
8
8
1
HCPL-2530/HCPL-2531
6N135, 6N136, HCPL-2503, HCPL-4502
1
Pin 7 is not connected in
Part Number HCPL-4502
DESCRIPTION
The HCPL-4502/HCPL-2503, 6N135/6 and HCPL-2530/HCPL-2531 optocouplers consist of an AlGaAs LED optically coupled to a
high speed photodetector transistor.
A separate connection for the bias of the photodiode improves the speed by several orders of magnitude over conventional
phototransistor optocouplers by reducing the base-collector capacitance of the input transistor.
An internal noise shield provides superior common mode rejection of 10kV/µs. An improved package allows superior insulation
permitting a 480 V working voltage compared to industry standard of 220 V.
FEATURES
•
•
•
•
•
•
High speed-1 MBit/s
Superior CMR-10 kV/µs
Dual-Channel HCPL-2530/HCPL-2531
Double working voltage-480V RMS
CTR guaranteed 0-70°C
U.L. recognized (File # E90700)
APPLICATIONS
•
•
•
•
Line receivers
Pulse transformer replacement
Output interface to CMOS-LSTTL-TTL
Wide bandwidth analog coupling
© 2003 Fairchild Semiconductor Corporation
Page 1 of 12
2/26/04
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
DUAL-CHANNEL: HCPL-2530
6N136
HCPL-2531
HCPL-2503
HCPL-4502
ABSOLUTE MAXIMUM RATINGS (T = 25°C unless otherwise specified)
A
Parameter
Symbol
Value
Units
Storage Temperature
Operating Temperature
Lead Solder Temperature
EMITTER
T
-55 to +125
-55 to +100
°C
°C
°C
STG
T
OPR
T
260 for 10 sec
SOL
DC/Average Forward Input Current
Each Channel (Note 1) I (avg)
25
50
mA
mA
F
Peak Forward Input Current (50% duty cycle, 1 ms P.W.)
I (pk)
F
Each Channel (Note 2)
Peak Transient Input Current - (≤1 µs P.W., 300 pps)
I (trans)
1.0
5
A
V
F
Each Channel
Each Channel
Reverse Input Voltage
V
P
R
D
Input Power Dissipation
(6N135/6N136 and HCPL-2503/4502)
100
45
mW
(HCPL-2530/2531 ) Each Channel (Note 3)
DETECTOR
Average Output Current
Peak Output Current
Emitter-Base Reverse Voltage
Supply Voltage
Each Channel
Each Channel
I
(avg)
(pk)
8
mA
mA
V
O
I
16
O
(6N135, 6N136 and HCPL-2503 only)
V
5
-0.5 to 30
-0.5 to 20
5
EBR
V
V
CC
Output Voltage
V
V
O
Base Current
(6N135, 6N136 and HCPL-2503 only)
(6N135, 6N136, HCPL-2503, HCPL-4502) (Note 4)
(HCPL-2530, HCPL-2531) Each Channel
I
mA
mW
mW
B
100
Output power
dissipation
P
D
35
© 2003 Fairchild Semiconductor Corporation
Page 2 of 12
2/26/04
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
DUAL-CHANNEL: HCPL-2530
6N136
HCPL-2531
HCPL-2503
HCPL-4502
ELECTRICAL CHARACTERISTICS (T = 0 to 70°C Unless otherwise specified)
A
INDIVIDUAL COMPONENT CHARACTERISTICS
Parameter
Test Conditions
(I = 16 mA, T =25°C)
Symbol
Device
Min Typ** Max Unit
EMITTER
1.45
1.7
1.8
F
A
V
V
F
Input Forward Voltage
Input Reverse BreakdownVoltage
(I = 16 mA)
F
(I = 10 µA)
B
5.0
V
R
VR
Temperature coefficient of
forward voltage
(I = 16 mA) (∆V /∆T )
-1.6
mV/°C
F
F
A
DETECTOR
(I = 0 mA, V = V = 5.5 V)
F
O
CC
All
0.001 0.5
(T =25°C)
A
6N135
6N136
HCPL-4502
HCPL-2503
Logic high output current
(I = 0 mA, V = V = 15 V)
I
µA
µA
F
O
CC
OH
0.005
1
(T =25°C)
A
(I = 0 mA, V = V = 15 V)
All
50
F
O
CC
6N135
6N136
HCPL-4502
HCPL-2503
(I = 16 mA, V = Open)
F
O
120
200
200
(V = 15 V)
CC
Logic low supply current
I
CCL
(I = I = 16 mA, V = Open)
HCPL-2530
HCPL-2531
F1
F2
O
400
1
(V = 15 V)
CC
6N135
6N136
HCPL-4502
HCPL-2503
(I = 0 mA, V = Open, V = 15 V)
F
O
CC
(T =25°C)
A
6N135
6N136
HCPL-4502
HCPL-2503
Logic high supply current
I
µA
CCH
(I = 0 mA, V = Open)
F
O
2
4
(V = 15 V)
CC
(I = 0 mA, V = Open)
HCPL-2530
HCPL-2531
F
O
0.02
(V = 15 V)
CC
** All Typicals at T = 25°C
A
© 2003 Fairchild Semiconductor Corporation
Page 3 of 12
2/26/04
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
DUAL-CHANNEL: HCPL-2530
6N136
HCPL-2531
HCPL-2503
HCPL-4502
TRANSFER CHARACTERISTICS (T = 0 to 70°C Unless otherwise specified)
A
Parameter
COUPLED
Test Conditions
Symbol
Device
Min Typ** Max Unit
6N135
HCPL-2530
7
18
27
50
50
%
%
(I = 16 mA, V = 0.4 V)
6N136
HCPL-4502
HCPL-2531
F
O
(V = 4.5 V, T =25°C)
19
CC
A
HCPL-2503
6N135
12
5
27
21
%
%
CTR
Current transfer ratio
(Note 5)
V
=0.4V
=0.5V
OL
V
HCPL-2530
OL
6N136
HCPL-4502
(I = 16 mA, V = 4.5 V)
V
=0.4V
F
CC
OL
15
9
30
%
%
V
V
=0.5V
=0.4V
HCPL-2531
HCPL-2503
6N135
OL
30
OL
0.18
0.18
0.4
0.5
(I = 16 mA, I = 1.1 mA)
F
O
(V = 4.5 V, T =25°C)
HCPL-2530
CC
A
6N136
HCPL-2503
0.25
0.25
0.4
0.5
0.5
(I = 16 mA, I = 3 mA)
F
O
(V = 4.5 V, T =25°C)
V
CC
A
Logic low output voltage
output voltage
V
HCPL-2531
OL
(I = 16 mA, I = 0.8 mA)
6N135
HCPL-2530
F
O
(V = 4.5 V)
CC
(I = 16 mA, I = 2.4 mA)
HCPL-4502
HCPL-2531
F
O
0.5
(V = 4.5 V)
CC
** All Typicals at T = 25°C
A
© 2003 Fairchild Semiconductor Corporation
Page 4 of 12
2/26/04
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
DUAL-CHANNEL: HCPL-2530
6N136
HCPL-2531
HCPL-2503
HCPL-4502
SWITCHING CHARACTERISTICS (T = 0 to 70°C unless otherwise specified., V = 5 V)
A
CC
Parameter
Test Conditions
Symbol
Device
Min Typ** Max Unit
6N135
HCPL-2530
T = 25°C, (R = 4.1 kΩ, I = 16 mA) (Note 6) (Fig. 7)
0.45
0.45
1.5
0.8
2.0
1.0
1.5
0.8
2.0
1.0
µs
A
L
F
6N136
(R = 1.9 kΩ, I = 16 mA) (Note 7) (Fig. 7)
HCPL-4502
HCPL-2503
HCPL-2531
L
F
µs
T = 25°C
A
Propagation delay
time to logic low
T
6N135
HCPL-2530
PHL
(R = 4.1 kΩ, I = 16 mA) (Note 6) (Fig. 7)
µs
L
F
6N136
HCPL-4502
HCPL-2503
HCPL-2531
(R = 1.9 kΩ, I = 16 mA) (Note 7) (Fig. 7)
µs
L
F
6N135
HCPL-2530
T = 25°C, (R = 4.1 kΩ, I = 16 mA) (Note 6) (Fig. 7)
0.5
0.3
µs
A
L
F
6N136
(R = 1.9 kΩ, I = 16 mA) (Note 7) (Fig. 7)
HCPL-4502
HCPL-2503
HCPL-2531
L
F
µs
T = 25°C
A
Propagation delay
time to logic high
T
PLH
6N135
HCPL-2530
(R = 4.1 kΩ, I = 16 mA) (Note 6) (Fig. 7)
µs
L
F
6N136
HCPL-4502
HCPL-2503
HCPL-2531
(R = 1.9 kΩ, I = 16 mA) (Note 7) (Fig. 7)
µs
L
F
(I = 0 mA, V
= 10 V , R = 4.1 kΩ)
6N135
HCPL-2530
F
CM
P-P
L
10,000
10,000
10,000
10,000
V/µs
V/µs
V/µs
V/µs
(Note 8) (Fig. 8) T = 25°C
Common mode
transient
immunity at
logic high
A
6N136
|CM |
(I = 0 mA, V
= 10 V
)
H
F
CM
P-P
HCPL-4502
HCPL-2503
HCPL-2531
T = 25°C, (R = 1.9 kΩ)
A
L
(Note 8) (Fig. 8)
(I = 16 mA, V
= 10 V , R = 4.1 kΩ)
6N135
HCPL-2530
F
CM
P-P
L
(Note 8) (Fig. 8) T = 25°C
Common mode
transient
immunity at
logic low
A
6N136
|CM |
(I = 16 mA, V
= 10 V
)
L
F
CM
P-P
HCPL-4502
HCPL-2503
HCPL-2531
(R = 1.9 kΩ)
L
(Note 8) (Fig. 8)
** All Typicals at T = 25°C
A
© 2003 Fairchild Semiconductor Corporation
Page 5 of 12
2/26/04
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
DUAL-CHANNEL: HCPL-2530
6N136
HCPL-2531
HCPL-2503
HCPL-4502
ISOLATION CHARACTERISTICS (T = 0 to 70°C Unless otherwise specified)
A
Characteristics
Test Conditions
Symbol
Min
Typ**
Max
Unit
(Relative humidity = 45%)
Input-output
insulation leakage current
(T = 25°C, t = 5 s)
A
I
1.0
µA
I-O
(V = 3000 VDC)
I-O
(Note 9)
(RH ≤ 50%, T = 25°C)
A
Withstand insulation test voltage
V
2500
V
RMS
ISO
(Note 9) ( t = 1 min.)
12
Resistance (input to output)
Capacitance (input to output)
DC Current gain
(Note 9) (V = 500 VDC)
R
C
10
Ω
I-O
I-O
(Note 9) (f = 1 MHz)
0.6
pF
I-O
(I = 3 mA, V = 5 V)
HFE
150
O
O
Input-Input
Insulation leakage current
(RH ≤ 45%, V = 500 VDC) (Note 10)
I-I
I
0.005
µA
Ω
I-I
t = 5 s, (HCPL-2530/2531 only)
(V = 500 VDC) (Note 10)
11
I-I
Input-Input Resistance
Input-Input Capacitance
R
10
I-I
I-I
(HCPL-2530/2531 only)
(f = 1 MHz) (Note 10)
(HCPL-2530/2531 only)
C
0.03
pF
Notes
1. Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C.
2. Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C.
3. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C.
4. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C.
5. Current Transfer Ratio is defined as a ratio of output collector current, I , to the forward LED input current, I , times 100%.
O
F
6. The 4.1 kΩ load represents 1 LSTTL unit load of 0.36 mA and 6.1kΩ pull-up resistor.
7. The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and 5.6 kΩ pull-up resistor.
8. Common mode transient immunity in logic high level is the maximum tolerable (positive) dV /dt on the leading edge of the
cm
common mode pulse signal V , to assure that the output will remain in a logic high state (i.e., V >2.0 V). Common mode
CM
O
transient immunity in logic low level is the maximum tolerable (negative) dV /dt on the trailing edge of the common mode
cm
pulse signal, V , to assure that the output will remain in a logic low state (i.e., V <0.8 V).
CM
O
9. Device is considered a two terminal device: Pins 1, 2, 3 and 4 are shorted together and Pins 5, 6, 7 and 8 are shorted
together.
10. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
I
© 2003 Fairchild Semiconductor Corporation
Page 6 of 12
2/26/04
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
DUAL-CHANNEL: HCPL-2530
6N136
HCPL-2531
HCPL-2503
HCPL-4502
Fig. 1 Normalized CTR vs. Forward Current
Fig. 2 Normalized CTR vs.Temperature
1.2
1.0
0.8
0.6
0.4
0.2
0.0
1.2
1.0
0.8
0.6
0.4
0.2
0.0
V
V
= 0.4 V
I = 16mA
F
O
Normalized to:
= 16 mA
Normalized to:
T = 25°C
A
= 5 V
V
= 5 V
CC
CC
I
F
T
= 25°C
V
= 0.4 V
A
O
0.1
1
10
100
-60
-40
-20
0
20
40
60
80
100
I
- FORWARD CURRENT (mA)
T - TEMPERATURE (°C)
A
F
Fig. 4 Logic High Output Current
vs.Temperature
Fig. 3 Output Current vs. Output Voltage
1000
16
14
12
10
8
TA = 25°C
CC = 5 V
I
F = 40 mA
F = 35 mA
I
= 0 mA
F
V
V
V
= 5 V
CC
= 5 V
I
O
100
10
1
I
F = 30 mA
F = 25 mA
I
I
F = 20 mA
F = 15 mA
6
I
4
IF = 10 mA
2
IF = 5 mA
0.1
-60
0
-40
-20
0
20
40
60
80
100
0
2
4
6
8
10
12
14
16
18
20
T
- TEMPERATURE (°C)
V
- OUTPUT VOLTAGE (V)
A
O
Fig. 5 Propagation Delay vs.Temperature
Fig. 6 Propagation Delay vs. Load Resistance
800
700
600
500
400
300
200
100
0
10000
R
L = 4.1 K (TPLH)
RL = 4.1 K (TPLH)
I
- 16 mA (TPHL)
F
I
- 10 mA (TPHL)
F
1000
I
- 16 mA (TPLH)
F
I
V
= 16 mA
F
RL = 1.9 K (TPHL)
RL = 1.9 K (TPLH)
= 5 V
V
= 5 V
CC
CC
= 25°C
T
A
I
- 10 mA (TPLH)
F
100
-60
-40
-20
0
20
40
60
80
100
1
10
T
- TEMPERATURE (°C)
R = LOAD RESISTANCE (kΩ)
L
A
© 2003 Fairchild Semiconductor Corporation
Page 7 of 12
2/26/04
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
6N136
HCPL-2503
HCPL-4502
DUAL-CHANNEL:
HCPL-2530
HCPL-2531
Noise
Shield
Noise
Shield
Pulse
+
VCC
I
F
V
CC
Generator
+5 V
+5 V
VO
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
tr = 5ns
ZO = 50
Pulse
Ω
R
L
Generator
IF
+
V
F1
VB
tr = 5ns
ZO= 50
10% D.C.
I/f< 100µs
V01
-
10% DUTY CYCLE
I/f < 100µS
RL
Ω
VF
-
C
L
= 1.5 µF
VO
V02
-
VO
I
F
V
F2
0.1 µF
MONITOR
+
0.1 µF
IF Monitor
GND
Rm
Rm
C
L
= 1.5 µF
GND
Test Circuit for 6N135, 6N136, HCPL-2503 and HCPL- 4502
Test Circuit for HCPL-2530 and HCPL-2531
IF
0
5 V
VO
1.5 V
1.5 V
VOL
TPHL
TPLH
Fig. 7 Switching Time Test Circuit
IF
Noise
Shield
Noise
Shield
VCC
V
CC
+
+5 V
+5 V
VO
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
IF
R
L
+
V
F1
VB
V01
-
RL
A
VF
-
A
VO
V02
B
-
0.1 µF
VO
0.1 µF
B
VFF
V
F2
VFF
+
GND
GND
-
VCM
+
-
VCM
-
+
Pulse Gen
Pulse Gen
Test Circuit for 6N135, 6N136, HCPL-2503 and HCPL-4502
Test Circuit for HCPL-2530 and HCPL-2531
VCM 10 V
0 V
90% 90%
10%
tr
10%
tf
VO
5 V
Switch at A : IF = 0 mA
VO
VOL
Switch at A : IF = 16 mA
Fig. 8 Common Mode Immunity Test Circuit
© 2003 Fairchild Semiconductor Corporation
Page 8 of 12
2/26/04
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
6N136
HCPL-2503
HCPL-4502
DUAL-CHANNEL:
HCPL-2530
HCPL-2531
Package Dimensions (Through Hole)
Package Dimensions (Surface Mount)
0.390 (9.91)
0.370 (9.40)
PIN 1
ID.
PIN 1
ID.
4
3
2
1
4
5
6
2
7
1
0.270 (6.86)
0.250 (6.35)
0.270 (6.86)
0.250 (6.35)
8
0.390 (9.91)
0.370 (9.40)
5
6
7
8
0.070 (1.78)
0.045 (1.14)
0.300 (7.62)
TYP
0.070 (1.78)
0.045 (1.14)
0.200 (5.08)
0.140 (3.55)
0.020 (0.51)
MIN
0.016 (0.41)
0.008 (0.20)
0.020 (0.51) MIN
0.154 (3.90)
0.120 (3.05)
0.045 [1.14]
0.022 (0.56)
0.016 (0.41)
0.022 (0.56)
0.016 (0.41)
15° MAX
0.315 (8.00)
MIN
0.016 (0.40)
0.008 (0.20)
0.100 (2.54) TYP
0.300 (7.62)
TYP
0.100 (2.54)
TYP
0.405 (10.30)
MIN
Lead Coplanarity : 0.004 (0.10) MAX
Package Dimensions (0.4” Lead Spacing)
4
3
2
1
PIN 1
ID.
0.270 (6.86)
0.250 (6.35)
5
6
7
8
0.390 (9.91)
0.370 (9.40)
0.070 (1.78)
0.045 (1.14)
0.200 (5.08)
0.140 (3.55)
0.004 (0.10) MIN
NOTE
All dimensions are in inches (millimeters)
0.154 (3.90)
0.120 (3.05)
0.022 (0.56)
0.016 (0.41)
0° to15°
0.016 (0.40)
0.008 (0.20)
0.100 (2.54) TYP
0.400 (10.16)
TYP
© 2003 Fairchild Semiconductor Corporation
Page 9 of 12
2/26/04
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
6N136
HCPL-2503
HCPL-4502
DUAL-CHANNEL:
HCPL-2530
HCPL-2531
ORDERING INFORMATION
Option
Example Part Number
Description
S
SD
T
6N135S
6N135SD
6N135T
Surface Mount Lead Bend
Surface Mount; Tape and reel
0.4" Lead Spacing
V
6N135V
VDE0884
TV
SV
SDV
6N135TV
6N135SV
6N135SDV
VDE0884; 0.4” lead spacing
VDE0884; surface mount
VDE0884; surface mount; tape and reel
MARKING INFORMATION
1
2
2503
6
V XX YY T1
5
3
4
Definitions
1
2
Fairchild logo
Device number
VDE mark (Note: Only appears on parts ordered with VDE
option – See order entry table)
3
4
5
6
Two digit year code, e.g., ‘03’
Two digit work week ranging from ‘01’ to ‘53’
Assembly package code
© 2003 Fairchild Semiconductor Corporation
Page 10 of 12
2/26/04
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
6N136
HCPL-2503
HCPL-4502
DUAL-CHANNEL:
HCPL-2530
HCPL-2531
Carrier Tape Specifications
12.0 0.1
4.0 0.1
Ø1.55 0.05
1.75 0.10
4.90 0.20
4.0 0.1
0.30 0.05
7.5 0.1
16.0 0.3
10.30 0.20
13.2 0.2
Ø1.6 0.1
0.1 MAX
10.30 0.20
User Direction of Feed
Reflow Profile
300
250
200
150
100
50
215C, 10–30 s
225C peak
Time above 183C, 60–150 sec
Ramp up = 3C/sec
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
Time (Minute)
• Peak reflow temperature: 225C (package surface temperature)
• Time of temperature higher than 183C for 60–150 seconds
• One time soldering reflow is recommended
© 2003 Fairchild Semiconductor Corporation
Page 11 of 12
2/26/04
HIGH SPEED
TRANSISTOR OPTOCOUPLERS
SINGLE-CHANNEL: 6N135
6N136
HCPL-2503
HCPL-4502
DUAL-CHANNEL:
HCPL-2530
HCPL-2531
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO
ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME
ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN;
NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES
OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and (c) whose failure to perform
when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to
result in a significant injury of the user.
2. A critical component in any component of a life support
device or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
© 2003 Fairchild Semiconductor Corporation
Page 12 of 12
2/26/04
©2020 ICPDF网 联系我们和版权申明