ZX-XF22 [OMRON]
Smart Sensors (Laser Type) ZX Series (ZX-L-N); 智能传感器（激光型） ZX系列（ ZX - L-N ）
| 型号： | ZX-XF22 |
| 厂家： | 
OMRON ELECTRONICS LLC |
| 描述： | Smart Sensors (Laser Type) ZX Series (ZX-L-N) |
| 文件： | 总29页 (文件大小：899K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Smart Sensors (Laser Type)
ZX Series (ZX-L-N)
.
Ordering Information
■ Sensors
Sensor Heads (Reflective)
Optical system
Beam shape
Sensing distance
40 10 mm
Resolution*1
Model
Diffuse reflective
Spot beam
2 µm
ZX-LD40
100 40 mm
300 200 mm
40 10 mm
100 40 mm
300 200 mm
30 2 mm
16 µm
300 µm
2 µm
16 µm
300 µm
0.25 µm
ZX-LD100
ZX-LD300
ZX-LD40L
Line beam
ZX-LD100L
ZX-LD300L
ZX-LD30V
ZX-LD30VL
Regular reflective
Spot beam
Line beam
*1. For an average count of 4,096.
Sensor Heads (Through-beam)
Optical system
Measuring width
Sensing distance
Resolution*1
Model
Through-beam
1-mm dia.
0 to 2000 mm
0 to 500 mm
4 µm
ZX-LT001
ZX-LT005
ZX-LT010
ZX-LT030
5 mm
10 mm
30 mm
12 µm
*1. For an average count of 64.
Amplifier Units
Appearance
Power supply
Output type
Model
DC
NPN
PNP
ZX-LDA11-N
ZX-LDA41-N
Note: Compatible connection with the Sensor Head.
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
1
Accessories (Order Separately)
Calculating Unit
Setup Tool for Personal Computer
Appearance
Model
Appearance
Name
Model
ZX-CAL2
Communications Interface
Unit (RS-232C) + Smart
Monitor Basic*2 (Function
Setting Software)
ZX-SFW11EV3
(See note 1.)
+
Note 1. The ZX-SFW11EV3 or ZX-SW11EV3 is required to use the
Smart Monitor with the ZX-LDA11-N/41-N. Earlier versions
cannot be used.
Side-view Attachments
2. The Smart Monitor Basic does not have a logging function.
Other than the logging function, the Smart Monitor Basic sup-
ports the same functions as the Smart Monitor.
Appearance
Applicable
Sensor Head
Model
Quantity
ZX-LT1001/
LT005
ZX-XF12
ZX-XF22
1
Cables with Connectors on Both Ends (for
Extension)*1
ZX-LT010
Cable length
Model
Quantity
1 m
4 m
8 m
ZX-XC1A
1
ZX-XC4A
ZX-XC8A
ZX-XC9A
Logging Tool for Personal Computers
Appearance
Name
Model
9 m *2
Communica-
tions Interface
Unit
RS-232C
USB
ZX-SF11
*1. Robot Cable models are also available. The model numbers are ZX-XC@R.
*2. For use only with Reflective Sensors.
ZX-SF21
Smart Monitor (Logging Soft- ZX-SW11EV3
ware + Function Setting Soft- (See note 1.)
ware)
2
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
Specifications
■ Sensor Heads (Reflective)
Item
Model ZX-LD40
ZX-LD100
ZX-LD300
ZX-LD30V
ZX-LD40L ZX-LD100L ZX-LD300L Z3X-LD30VL
Optical system
Diffuse reflective
Regular re- Diffuse reflective
flective
Regular reflec-
tive
Light source (wave
length)
Visible-light semiconductor laser with a wavelength of 650 nm and an output of 1 mW max.
EN class 2, FDA class II
Measurement point
Measurement range
Beam shape
40 mm
10 mm
Spot
100 mm
40 mm
300 mm
200 mm
30 mm
2 mm
40 mm
10 mm
Line
100 mm
40 mm
300 mm
200 mm
30 mm
2 mm
Beam size*1
50-µm dia.
100-µm dia. 300-µm dia. 75-µm dia.
75 µm x 2
150 µm x 2 450 µm x 2 100 µm x 1.8
mm
mm
mm
mm
Resolution*2
Linearity*3
2 µm
0.2% FS
(entire
range)
16 µm
0.2% FS
(80 to 120
mm)
300 µm
2% FS
0.25 µm
0.2% FS
2 µm
0.2% FS
(32 to 48
mm)
16 µm
0.2% FS
(80 to 120
mm)
300 µm
2% FS
0.25 µm
0.2% FS
(200 to 400 (entire
(200 to 400 (entire range)
mm)
mm)
range)
Temperature
characteristic*4
0.03% FS/°C (Except for ZX-LD300 and ZX-LD300L, which are 0.1% FS/°C.)
Ambient illumination
Ambient temperature
Ambient humidity
Incandescent lamp: 3,000 l× max. (on light receiving side)
Operating: 0 to 50°C, Storage: −15 to 60°C (with no icing or condensation)
Operating and storage: 35% to 85% (with no condensation)
20 MΩ min. at 500 VDC
Insulation resistance
Dielectric strength
1,000 VAC, 50/60 Hz for 1 min
Vibration resistance
(destruction)
10 to 150 Hz, 0.7-mm double amplitude 80 min each in X, Y, and Z directions
Shock resistance
(destruction)
300 m/s2 3 times each in six directions (up/down, left/right, forward/backward)
Degree of protection
IEC60529, IP50
IEC60529,
IP40
IEC60529, IP50
IEC60529,
IP40
Connection method
Weight (packed state)
Connector relay (standard cable length: 500 mm)
Approx. 150 g
Approx. 250 Approx. 150 g
g
Approx. 250 g
Materials
Case: PBT (polybutylene terephthalate), Case and
Case: PBT (polybutylene terephthalate), Case and cov-
Cover: Aluminum, Lens: Glass
cover: Alumi- Cover: Aluminum, Lens: Glass
er: Aluminum,
Lens: Glass
num, Lens:
Glass
Accessories
Instruction sheet, Laser warning label (English)
*1. Beam size: The beam size is defined by 1/e2 (13.5%) of the strength of the beam at the beam center (measured value). Incorrect detection may
occur if there is light leakage outside the defined spot and the material around the sensing object is more reflective than the sensing object.
*2. Resolution: The resolution is the deviation ( 3σ) in the linear output when connected to the ZX-LDA Amplifier Unit. (The resolution is measured
with the standard reference object (white ceramic), at the measurement point with the ZX-LDA set for an average count of 4,096 per period.)
The resolution is given at the repeat accuracy for a stationary workpiece, and is not an indication of the distance accuracy. The resolution may
be adversely affected under strong electromagnetic fields.
*3. Linearity: The linearity is given as the error in an ideal straight line displacement output when measuring the standard reference object. The
linearity and measurement values vary with the object being measured.
*4. Temperature characteristic: The temperature characteristic is measured at the measurement point with the Sensor and reference object
(OMRON’s standard reference object) secured with an aluminum jig.
Note: Highly reflective objects can result in incorrect detection by causing out-of-range measurements.
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
3
■ Sensor Heads (Through-beam)
Item
Model
ZX-LT001
Through-beam
ZX-LT005
ZX-LT010
ZX-LT030
Optical system
Light source
(wave length)
Visible-light semiconductor laser with a wavelength of 650 nm
EN class 1, FDA class II
Maximum output
0.2 mW max.
1-mm dia.
0.35 mW max.
1- to 2.5-mm dia. 5 mm
0.2 mW max.
Measurement width
10 mm
30 mm
Measurement
distance
0 to 500 mm
500 to 2,000 mm 0 to 500 mm
Minimum sensing
object
8-µm dia.
(opaque)
8- to 50-µm dia. 0.05-mm dia. (opaque)
(opaque)
0.1-mm dia. (opaque)
0.3-mm dia. (opaque)
Resolution*1
4 µm *2
---
4 µm *3
12 µm *4
Temperature
characteristic
0.2% FS/°C
0.3% FS/°C
Ambient illumination Incandescent lamp: 10,000 l× max. (on light-receiving side)
Ambient temperature Operating: 0 to 50°C, Storage: −25 to 70°C (with no icing or condensation)
Ambient humidity Operating: 35% to 85% (with no condensation)
Degree of protection IEC60529, IP40
Connection method
Connector relay (standard cable length: 500 mm)
Weight (packed state) Approx. 220 g
Approx. 450 g
Zinc die-cast
Cable length
Materials Case
Cover
Extendable up to 10 m with special extension cable.
Polyetherimide
Polycarbonate
Front filter Glass
Tightening torque
Accessories
0.3 N⋅m max.
Instruction sheet, Sensor Head-Amplifier Connection Cable
Optical axis adjustment seal
Mounting Bracket
*1. This value is obtained by converting the deviation ( 3σ) in the linear output that results when the sensor head is connected to the amplifier unit,
into the measurement width.
*2. For an average count of 64. The value is 5 µm for an average count of 32.
This is the value that results when a minimum sensing object blocks the light near the center of the 1-mm measurement width.
*3. For an average count of 64. The value is 5 µm for an average count of 32.
*4. For an average count of 64. The value is 15 µm for an average count of 32.
4
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
■ Amplifier Units
Item
Model
ZX-LDA11-N
ZX-LDA41-N
Measurement period
150 µs
Possible average count settings*1 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1,024, 2,048, or 4,096
Temperature characteristic
When connected to a Reflective Sensor Head: 0.01% FS/°C, When connected to a Through-beam Sensor
Head: 0.1% FS/°C
Linear output*2
4 to 20 mA/FS, Max. load resistance: 300 Ω, 4 V ( 5 V, 1 to 5 V *3), Output impedance: 100 Ω
Judgement outputs
(3 outputs: HIGH/PASS/LOW)*1
NPN open-collector outputs, 30 VDC, 50 mA max. PNP open-collector outputs, 30 VDC, 50 mA max.
Residual voltage: 1.2 V max.
Residual voltage: 2 V max.
Laser OFF input, zero reset input, ON: Short-circuited with 0-V terminal or 1.5 V or less ON: Supply voltage short-circuited or supply voltage
timing input, reset input
OFF: Open (leakage current: 0.1 mA max.)
within 1.5 V
OFF: Open (leakage current: 0.1 mA max.)
Functions
Measurement value display, present value/set value/light level/resolution display, scaling, display reverse,
display OFF mode, ECO mode, number of display digit changes, sample hold, peak hold, bottom hold,
peak-to-peak hold, self-peak hold, self-bottom hold, average hold, delay hold, intensity mode, zero reset,
initial reset, ON-delay timer, OFF-delay timer, one-shot timer, deviation, previous value comparison,
sensitivity adjustment, keep/clamp switch, direct threshold value setting, position teaching, 2-point
teaching, automatic teaching, hysteresis width setting, timing inputs, reset input, monitor focus, linear
output compensation, (A-B) calculations*4, (A+B) calculations*4, mutual interference*4, laser
deterioration detection, zero reset memory, zero reset display, key lock
Indications
Operation indicators: High (orange), pass (green), low (yellow), 7-segment main display (red), 7-segment
subdisplay (yellow), laser ON (green), zero reset (green), enable (green)
Power supply voltage
Current consumption
Ambient temperature
Ambient humidity
12 to 24 VDC 10%, Ripple (p-p): 10% max.
140 mA max. with power supply voltage of 24 VDC (with Sensor connected)
Operating: 0 to 50°C, Storage: −15 to 60°C (with no icing or condensation)
Operating and storage: 35% to 85% (with no condensation)
20 MΩ min. at 500 VDC
Insulation resistance
Dielectric strength
1,000 VAC, 50/60 Hz for 1 min
Vibration resistance
(destruction)
10 to 150 Hz, 0.7-mm double amplitude 80 min each in X, Y, and Z directions
Shock resistance
(destruction)
300 m/s2 3 times each in six directions (up/down, left/right, forward/backward)
Connection method
Weight (packed state)
Materials
Prewired (standard cable length: 2 m)
Approx. 350 g
Case: PBT (polybutylene terephthalate), Cover: Polycarbonate
Instruction sheet
Accessories
*1. The response speed of the linear output is calculated as the measurement period × (average count setting + 1) (with fixed sensitivity).
The response speed of the judgement outputs is calculated as the measurement period × (average count setting + 1) (with fixed sensitivity).
*2. The output can be switched between a current output and voltage output using a switch on the bottom of the Amplifier Unit.
*3. Setting is possible via the monitor focus function.
*4. A Calculating Unit (ZX-CAL2) is required.
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
5
■ Calculating Unit
Item
Applicable Amplifier Units
Current consumption
Ambient temperature
Ambient humidity
ZX-CAL2
ZX-LDA11-N/41-N/ZX-EDA11/41/ZX-TDA11/41
12 mA max. (supplied from the Smart Sensor Amplifier Unit)
Operating: 0 to 50°C, Storage: −15 to 60°C (with no icing or condensation)
Operating and storage: 35% to 85% (with no condensation)
Connector
Connection method
Dielectric strength
1,000 VAC, 50/60 Hz for 1 min
Insulation resistance
Vibration resistance (destructive)
Shock resistance (destructive)
Materials
100 MΩ (at 500 VDC)
10 to 150 Hz, 0.7-mm double amplitude 80 min each in X, Y, and Z directions
300 m/s2 3 times each in six directions (up/down, left/right, forward/backward)
Display: Acrylic, Case: ABS resin
Weight (packed state)
Approx. 50 g
■ ZX-series Communications Interface Unit
Item
ZX-SF11
Current consumption
60 mA max. (supplied by the Amplifier Unit)
ZX Series
Applicable Amplifier Units
Applicable Amplifier Unit versions
ZX-LDA@1-N Ver. 1.000 or higher
ZX-EDA@1 Ver. 1.100 or higher
ZX-TDA@1 Ver. 1.000 or higher
Max. No. of Amplifier Units
5
Communications
functions
Communications
port
RS-232C port (9-pin D-Sub Connector)
Communications
protocol
CompoWay/F*
38,400 bps
Baud rate
Data configuration Data bits: 8, Parity: none, Start bits: 1, Stop bits: 1, Flow control: none
Indicators
Power supply: green, Sensor communications: green, Sensor communications error: red, External
terminal communications: green, External terminal communications error: red
Protective circuits
Ambient temperature
Ambient humidity
Insulation resistance
Dielectric strength
Materials
Reverse polarity protection
Operating: 0 to 50°C, storage: −15 to 60°C (with no icing or condensation)
Operating and storage: 35% to 85% (with no condensation)
20 MΩ min. (at 500 VDC)
1,000 VAC, 50/60 Hz for 1 min, Leakage current: 10 mA max.
Case: PBT (polybutylene terephthalate), Cover: Polycarbonate
Instruction sheet, 2 clamps
Accessories
* Contact your OMRON representative for CompoWay/F communications specifications.
6
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
Engineering Data (Typical)
Angle Characteristic (Reflective Sensors)
The angle characteristic plots the relation between the inclination of the measurement object and the error in the linear output at the measure-
ment point.
Note: SUS304 = Stainless steel SUS304
● ZX-LD100
Side-to-side Inclination
4
● ZX-LD300
Side-to-side Inclination
20
● ZX-LD40
Side-to-side Inclination
4
White ceramic
SUS304
Black
paper
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
3
2
15
10
5
3
2
+ inclination
+ inclination
− inclination
− inclination
1
1
0
0
0
−1
−2
−5
−10
−1
−2
+ inclination
− inclination
−3
−4
−15
−20
−3
−4
Angle of inclination (°) 10
−10 −8 −6 −4 −2
0
2
4
6
8
−10 −8 −6 −4 −2
0
2
4
6
8
Angle of inclination (°1)0
−10 −8 −6 −4 −2
0
2
4
6
8
10
Angle of inclination (°)
Front-to-back Inclination
Front-to-back Inclination
Front-to-back Inclination
4
20
4
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
3
2
15
10
5
3
2
+ inclination
− inclination
1
1
0
0
0
−1
−2
−5
−10
−1
−2
+ inclination
+ inclination
−3
−4
−15
−20
−3
−4
− inclination
− inclination
−10 −8 −6 −4 −2
0
2
4
6
8
10
−10 −8 −6 −4 −2
0
2
4
6
8
10
−10 −8 −6 −4 −2
0
2
4
6
8
10
Angle of inclination (°)
Angle of inclination (°)
Angle of inclination (°)
● ZX-LD100L
Side-to-side Inclination
● ZX-LD300L
Side-to-side Inclination
● ZX-LD40L
Side-to-side Inclination
4
4
4
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
3
2
3
2
3
2
+ inclination
+ inclination
− inclination
− inclination
1
1
1
0
0
0
−1
−2
−1
−2
−1
−2
+ inclination
−3
−4
−3
−4
−3
−4
− inclination
−10 −8 −6 −4 −2
0
2
4
6
8
10
−10 −8 −6 −4 −2
0
2
4
6
8
10
−10 −8 −6 −4 −2
0
2
6
8
10
Angle of 4inclination (°)
Angle of inclination (°)
Angle of inclination (°)
Front-to-back Inclination
Front-to-back Inclination
Front-to-back Inclination
20
4
White ceramic
SUS304
Black paper
4
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
15
3
2
3
2
+ inclination
10
5
− inclination
1
1
0
0
0
−5
−10
−1
−2
−1
−2
+ inclination
− inclination
10
−15
−20
+ inclination
−3
−4
−3
−4
− inclination
−10 −8 −6 −4 −2
0
2
4
6
8
−10 −8 −6 −4 −2
0
2
4
6
8
10
−10 −8 −6 −4 −2
0
2
4
6
8
10
Angle of inclination (°)
Angle of inclination (°)
Angle of inclination (°)
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
7
● ZX-LD30VL
Side-to-side Inclination
● ZX-LD30V
Side-to-side Inclination
4
4
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
3
3
+ inclination
2
+ inclination
2
− inclination
− inclination
1
1
0
−1
−2
0
−1
−2
−
3
−3
−4
−10 −8 −6 −4 −2
−4
0
4
6
8
10
Angle2of inclination (°)
−10 −8 −6 −4 −2
0
2
4
6
8
10
Angle of inclination (°)
Front-to-back Inclination
Front-to-back Inclination
4
4
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
3
3
+ inclination
2
1
2
1
− inclination
0
0
−1
−2
−1
−2
−3
−4
+ inclination
−3
−4
− inclination
−10 −8 −6 −4 −2
−10 −8 −6 −4 −2
0
4
6
8
Angle2of inclination (°1)0
0
2
4
6
8
10
Angle of inclination (°)
8
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
Linearity Characteristic for Different Materials (Reflective Sensors)
● ZX-LD40
0° Inclination
10° Inclination
4
−10° Inclination Front-to-back
4
4
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
White ceramic
SUS304
3
2
3
2
3
Black paper
2
0° inclination
10° inclination
1
1
1
0
0
−1
−2
0
−1
−2
−1
−2
−3
−4
−3
−4
−3
−4 −10° inclination
30 32 34 36 38 40 42 44 46 48 50
Distance (mm)
30 32 34 36 38 40 42 44 46 48 50
Distance (mm)
30 32 34 36 38 40 42 44 46 48 50
Distance (mm)
● ZX-LD100
0° Inclination
−10° Inclination Front-to-back
10° Inclination
4
4
4
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
3
2
3
2
3
2
−10° inclination
0° inclination
10° inclination
1
1
1
0
−1
−2
−3
0
−1
−2
−3
0
−1
−2
−3
−4
−4
−4
60 68 76 84 92 100 108 116 124 132 140
60 68 76 84 92 100 108 116 124 132 140
60 68 76 84 92 100 108 116 124 132 140
Distance (mm)
Distance (mm)
Distance (mm)
● ZX-LD300
0° Inclination
10° Inclination
−10° Inclination Front-to-back
5
5
5
White ceramic
White ceramic
SUS304
Black paper
4
4
3
SUS304
Black paper
4
3
3
2
2
2
1
1
1
0
0
0
−1
−2
−1
−2
−3
−1
−2
−3
−3
White ceramic
SUS304
Black paper
−4
−5
−4
−5
−4
−5
10° inclination
−10° inclination
0° inclination
100 140 180 220 260 300 340 380 420 460 500
Distance (mm)
100 140 180 220 260 300 340
420 460 500
Di3s8t0ance (mm)
100 140 180 220 260 300 340 380 420 460 500
Distance (mm)
● ZX-LD40L
0° Inclination
10° Inclination
4
−10° Inclination Front-to-back
4
4
White ceramic
White ceramic
SUS304
Black paper
White ceramic
SUS304
Black paper
SUS304
Black
paper
3
2
3
2
3
2
10° inclination
0° inclination
1
1
1
0
0
−1
−2
−3
0
−1
−2
−3
−1
−2
−3
−10° inclination
−4
−4
−4
30 32 34 36 38 40 42 44 46 48 50
30 32 34 36 38 40 42 44 46 48 50
30 32 34 36 38 40 42 44 46 48 50
Distance (mm)
Distance (mm)
Distance (mm)
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
9
● ZX-LD100L
0° Inclination
4
−10° Inclination Front-to-back
10° Inclination
4
4
White ceramic
SUS304
Black paper
White ceramic
White ceramic
SUS304
Black paper
SUS304
Black paper
3
2
3
2
3
2
0° inclination
−10° inclination
1
1
10° inclination
1
0
−1
−2
0
−1
−2
−3
0
−1
−2
−3
−4
−3
−4
−4
60 68 76 84 92 100 108 116 124 132 140
Distance (mm)
60 68 76 84 92 100 108 116 124 132 140
60 68 76 84 92 100 108 116 124 132 140
Distance (mm)
Distance (mm)
● ZX-LD300L
0° Inclination
10° Inclination
4
−10° Inclination Front-to-back
4
4
White ceramic
White ceramic
SUS304
Black paper
3
2
3
2
SUS304
Black paper
3
2
−10° inclination
10° inclination
0° inclination
1
1
1
0
0
−1
−2
−3
0
−1
−2
−3
−1
−2
White ceramic
SUS304
Black paper
−3
−4
−4
−4
100 140 180 220 260 300 340 380 420 460 500
100 140 180 220 260 300 340 380 420 460 500
100 140 180 220 260 300 340 380 420 460 500
Distance (mm)
Distance (mm)
Distance (mm)
● ZX-LD30V
0° Inclination
1.0
10° Inclination
−10° Inclination Front-to-back
1.0
1.0
White ceramic
White ceramic
White ceramic
SUS304
Black paper
0.8
0.6
SUS304
Black paper
0.8
0.6
SUS304
Black paper
0.8
0.6
0.4
0.4
0.4
10° inclination
−10° inclination
0.2
0.2
0.2
0
0
0
−0.2
−0.4
−0.6
−0.2
−0.4
−0.6
−0.2
−0.4
−0.6
−0.8
−1.0
−0.8
−1.0
−0.8
−1.0
0° inclination
28.0 28.4 28.8 29.2 29.6 30.0 30.4 30.8 31.2 31.6 32.0
28.0 28.4 28.8 29.2 29.6 30.0 30.4 30.8 31.2 31.6 32.0
28.0 28.4 28.8 29.2 29.6 30.0 30.4 30.8 31.2 31.6 32.0
Distance (mm)
Distance (mm)
Distance (mm)
● ZX-LD30VL
0° Inclination
10° Inclination
−10° Inclination Front-to-back
1.0
1.0
1.0
White ceramic
SUS304
Black paper
White ceramic
White ceramic
0.8
0.6
0.8
0.6
SUS304
Black paper
0.8
0.6
SUS304
Black paper
0.4
0.4
0.4
10° inclination
−10° inclination
0.2
0.2
0.2
0
0
0
−0.2
−0.4
−0.6
−0.2
−0.4
−0.6
−0.2
−0.4
−0.6
−0.8
−1.0
−0.8
−1.0
−0.8
−1.0
0° inclination
28.0 28.4 28.8 29.2 29.6 30.0 30.4 30.8 31.2 31.6 32.0
Distance (mm)
28.0
28.4 28.8 29.2 29.6 30.0 30.4 30.8 31.2 31.6 32.0
28.0 28.4 28.8 29.2 29.6 30.0 30.4 30.8 31.2 31.6 32.0
Distance (mm)
Distance (mm)
10
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
Beam Size
(Reflective Sensors)
● Spot Beams
L
● Spot Beams
L
Beam cross-section
Y
Beam cross-section
Y
X
X
ZX-LD30V
L
X
Y
28 mm
30 mm
32 mm
120 µm
90.0 µm
ZX-LD40
60.0 µm
50.0 µm
30.0 µm
40.0 µm
L
X
Y
30 mm
240 µm
350 µm
40 mm
50 mm
250 µm
370 µm
40.0 µm
30.0 µm
● Line Beams
ZX-LD100
L
L
60 mm
100 mm
140 mm
X
Y
390 µm
620 µm
100 µm
65.0 µm
430 µm
650 µm
Beam cross-section
ZX-LD300
L
Y
100 mm
300 mm
500 mm
X
Y
1,050 µm
450 µm
180 µm
300 µm
1,100 µm
850 µm
X
ZX-LD30VL
L
X
Y
28 mm
30 mm
32 mm
1,800 µm
90.0 µm
1,800 µm
60.0 µm
1,800 µm
110 µm
● Line Beams
L
Beam cross-section
Y
X
ZX-LD40L
L
X
Y
30 mm
40 mm
50 mm
2,000 µm
240 µm
2,000 µm
50.0 µm
2,000 µm
250 µm
ZX-LD100L
L
60 mm
100 mm
140 mm
X
Y
2,000 µm
410 µm
2,000 µm
100 µm
2,000 µm
430 µm
ZX-LD300L
L
100 mm
300 mm
500 mm
X
Y
2,000 µm
750 µm
2,000 µm
300 µm
2,500 µm
650 µm
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
11
Sensing Object Characteristics (Through-beam Sensors)
● ZX-LT001
● ZX-LT001
(For 0.05-mm-dia. pin gauge)
● ZX-LT005
(For 0.05-mm-dia. pin gauge)
(For 0.02-mm-dia. pin gauge)
2
2
1
WD=50 mm
0
−2
−4
−6
WD=250 mm
WD=450 mm
Sensing distance: 500 mm
Sensing object: 0.05-mm dia.
0
0.5
0
−2
−4
−6
−0.5
−1
−8
−10
−12
−14
WD=50 mm
WD=250 mm
WD=200 mm
WD=500 mm
WD=1,000 mm
WD=1,500 mm
−8
WD=450 mm
−10
Sensing distance: 500 mm
−1.5
−2
Sensing object: 0.02-mm dia.
WD=1,800 mm
−12
Sensing distance: 2 m
Sensing object: 0.05-mm dia.
Pin gauge
Y
Pin gauge
−14
Y
Pin gauge Y
−16
−18
−2.5
−16
Emitter side WD
Receiver side
1.5 2.5
Emitter
Receiver side
Receiver side
2.5 5
WD
WD
Emitter side
−2.5
side
−18
0
−2.5
−1.5
−0.5
0.5
3
−
0
−2.5
−1.5
−0.5
0.5
1.5
2.5
−5
0
Light axis center
Detection position Y (mm)
Light axis center
Detection position Y (mm)
Light axis center
Detection position Y (mm)
● ZX-LT010
(For 0.1-mm-dia. pin gauge)
1
WD = 50 mm
WD = 250 mm
WD = 450 mm
Sensing distance: 500 mm
Sensing object: 0.1-mm dia.
0.5
0
0.5
1
1.5
2
Pin gauge
WD
Y
2.5
3
Receiver
side
Emitter side
8
4
0
4
8
Light axis center
Detection position Y (mm)
Linearity Characteristics
● ZX-LT005
● ZX-LT010
4
4
WD=50 mm
WD = 50 mm
WD = 250 mm
WD = 450 mm
WD=250 mm
WD=450 mm
Sensing distance: 500 mm
3
3
Sensing distance: 500 mm
2
2
1
0
1
2
1
0
−1
−2
Emitter
side
Receiver
side
Receiver
side
Emitter side
WD
3
4
−3
−4
WD
0
1
2
3
4
5
0
1
2
3
4
5
Light interruption (mm)
Light interruption (mm)
12
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
Linear Output vs. Sensing Distance
The output can be switched between a current output and a voltage output using a switch on the Amplifier Unit.
ZX-LD40/LD40L
Current Output
Voltage Output
Linear output (V)
6
Linear output (mA)
24
4
20
2
0
16
12
25 30
35
40 45
100 120
300 400
50 55
Distance (mm)
25 30
35
40 45
50 55
Distance (mm)
−2
−4
8
4
−6
0
ZX-LD100/LD100L
Current Output
Voltage Output
Linear output (V)
6
Linear output (mA)
24
4
20
2
0
16
12
40 60
80
140 160
Distance (mm)
40 60
80
100 120
140 160
Distance (mm)
−2
−4
8
4
−6
0
ZX-LD300/LD300L
Current Output
Voltage Output
Linear output (V)
6
24
Linear output (mA)
4
20
2
0
16
12
0
100
200
500 600
Distance (mm)
0
100
200
300 400
500 600
Distance (mm)
−2
−4
8
4
−6
0
ZX-LD30V/LD30VL
Current Output
Voltage Output
Measurement range
Measurement range
(4 mm)
(4 mm)
6
24
4
20
2
0
16
12
27
28
29
30 31
32
33
27
28
29
30 31
32
33
Distance (mm)
Distance (mm)
−2
−4
8
4
−6
0
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
13
I/O Circuit Diagrams
PNP Amplifier Unit: ZX-LDA41-N
NPN Amplifier Unit: ZX-LDA11-N
Brown: 12 to 24 VDC
Brown: 12 to 24 VDC
White: HIGH
output
White: HIGH output
Green: PASS output
Gray: LOW output
Green: PASS output
Gray: LOW output
12 to
24 VDC
12 to
24 VDC
Blue: GND (0V)
Blue: GND (0V)
Pink: Laser OFF input
Purple: Timing input
Pink: Laser OFF input
Purple: Timing input
Orange: Zero reset input
Red: Reset input
Orange: Zero reset input
Red: Reset input
Current output
4 to 20 mA
Current/voltage
Black: Linear output
switch
Current output
4 to 20 mA
Voltage output
4V
Black: Linear output
Shield: Linear GND
Current output: 300 Ω max.
Voltage output: 10 kΩ min.
Current/voltage
switch
Current output: 300 Ω max.
Voltage output: 10 kΩ min.
Voltage output
4V
Shield: Linear GND
100 Ω
100 Ω
Connections: Amplifier Unit
Brown:
12 to 24 VDC
Blue:
GND (0V)
White:
HIGH output
Green:
PASS output
Gray:
LOW output
Black:
Linear output
Shield:
Linear output GND
Pink:
Laser OFF input
Orange:
Zero reset input
Purple:
Timing input
Red:
Reset input
Note 1. Use a separate stabilized power supply for the Amplifier Unit,
particularly when high resolution is required.
2. Wire the Unit correctly. Incorrect wiring may result in damage to
the Unit. (Do not allow wiring, particularly the linear output, to
come into contact with other lines.)
3. Use the 0-V line (blue) for the power supply and use the shield
wire (linear output ground) together with the linear output (black
line) for linear output. Each of these grounds must be used for
the designed purpose. When not using the linear output, con-
nect the linear ground (shield) to the 0-V ground.
14
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
Part Names
Sensor Heads (Reflective)
ZX-LD40
Amplifier Units
ZX-LDA11-N
ZX-LDA41-N
ZX-LD100
Controls
ZX-LD300
ZX-LD40L
Display area
ZX-LD100L
ZX-LD300L
ZX-LD30V*
Display area
Input cable (with connector)
ZX-LD30VL*
Receiver
(Optical filter)
Output cable
Connector
(Cover opens and closes.)
Output cable (with connector)
*The dimensions for these models are slightly different. Refer to page 23 for details.
Sensor Heads (Through-beam)
ZX-LT001
Calculating Unit
ZX-CAL2
ZX-LT005
ZX-LT010
ZX-LT030
Display area
Emitter
Laser ON
indicator (green)
Light emitter
Lit when light is
emitted.
Emitter side
sensor head
connector
Emitter
Connector
Receiver side
(Optical filter)
Receiver side sensor
head connector
Receiver
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
15
Precautions
■ Design Precautions
■ Other Precautions
Ratings and Performance
Environment
• Conform to the specified ratings and performance. Refer to Speci-
fications for details.
1. Do not use the Sensor in strong electromagnetic fields or in an
environment where the operation of the Sensor is subject to
the reflection of intense light (such as other laser beams or
electric arc-welding machines.)
1. Do not impose voltage exceeding the rated voltage, otherwise
the Sensor may be damaged.
2. When supplying power to the Sensor, make sure that the
polarity of the power is correct, otherwise, the Sensor may be
damaged. Do not connect to an AC power supply.
3. Do not short-circuit the load for the open collector output, oth-
erwise the Sensor may be damaged.
2. Do not operate the Sensor in the following locations:
• Locations subject to strong vibration.
• Locations subject to direct sunlight or near heating equip-
ment.
• Locations subject to high humidity.
• Do not disconnect the connector connecting the Sensor Head and
the controller while power is being supplied, otherwise the Sensor
may be damaged.
• Allow a warm-up period of approximately 10 minutes after turning
ON the power supply.
• Locations where the Sensor would accumulate dust, dirt, me-
tallic powder, etc.
• Locations subject to corrosive or flammable gases.
• Locations subject to exposure to organic solvents, water, oil,
etc.
• Objects of certain materials or shapes may not be detectable, or the
detection accuracy may not be sufficiently high. These include ma-
terials that are transparent or have extremely low reflectivity, and
objects that are smaller than the Sensor’s spot diameter or have ex-
treme curvature or inclination.
• Locations subject to strong electromagnetic or electrical
fields.
• Locations subject to rapid changes in temperature.
• Locations subject to freezing.
Power Supply and Wiring
• Prior to turning ON the power supply after wiring is completed,
check to make sure that the power supply is correct, that there are
no mistaken connections, e.g., connections that would short-circuit
the load, and that the load current is appropriate. Incorrect wiring
may result in damage to the Sensor or Unit.
• The total length of the Sensor cable or Amplifier cable must be 10 m
or less. Use an ZX-XC@A Extension Cable (order separately) if re-
quired to extend the cable from the Sensor. Use a shielded cable to
extend the Amplifier cable. The shielded cable must be the same as
that of the Amplifier cable.
• Do not lay a power supply cable for the ZX together with high-volt-
age lines or power lines to prevent interference, damage, and mal-
function.
• When using a commercially available switching regulator, ground
the FG (frame ground) terminal.
• If the power supply line is subject to surges, connect a surge ab-
sorber that meets the conditions of the usage environment.
• When using a Calculating Unit, connect the corresponding linear
ground of the Amplifier Unit.
Compatibility
• All Sensor Heads and Amplifier Units are compatible. Different Sen-
sor Heads may be purchased at a later date and used with existing
Amplifier Units.
Mutual Interference
• Two Sensor Heads can be used together, without danger of mutual
interference, by connecting the ZX-CAL 2 Calculating Unit between
two Amplifier Units.
Maintenance
• Always turn OFF the power supply before adjusting or removing the
Sensor Head.
• Cleaning
Do not use thinners, benzine, acetone, or kerosene for cleaning.
If dust or oil adheres to the filter on the front of the Sensor Head,
use the following procedure to clean.
1. Use a blower brush (used to clean camera lenses) to blow
large dust particles from the surface. Do not blow the dust
away with your mouth.
2. Use a soft cloth (for lenses) with a small amount of alcohol to
remove the remaining dust. Do not use a scrubbing action
when cleaning because scratches on the filter could result in
Sensor inaccuracy.
16
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
Laser Safety
The ZX-LD-Series Sensor Heads are FDA Class II and EN Class 2 Laser Products. The ZX-LT-Series Sensor Heads are FDA Class II and EN
Class 1 Laser Products. The ZX Series is meant to be built into final system equipment. Pay special attention to the following precautions for the
safe use of the product:
Note: Europe: Class 1 and Class 2 of EN60825-1: 1994 = IEC825-1: 1993
U.S.A.: Class I and Class II of FDA (21 CFR1040.10)
1. Use this product as specified in this instruction manual. Otherwise, you may be exposed to hazardous laser radiation.
2. The ZX-series Smart Sensors radiate laser beams in the visible light range. Do not expose your eyes directly to the laser radiation. Ensure
that the laser beam path is terminated during use. If a mirror or shiny surface is positioned in the laser beam path, ensure that the reflected
beam path is also terminated. If the Unit must be used without terminating the laser beam path, position the laser beam path so that it is not
at eye level.
3. To avoid exposure to hazardous laser radiation, do not displace nor remove the protective housing during operation, maintenance, and any
other servicing.
4. The user should return the product to OMRON for all repair and servicing.
5. As for other countries, observe the regulations and standards specified by each country.
Requirements from Regulations and Standards
EN60825-1 “Safety of Laser Products, Equipment Classification, Requirements and User’s
Guide”
● Summary of Manufacturer’s Requirements
Requirements;
Sub-clause
Classification
Class 3A
Class 1
Class 2
Class 3B*
Class 4
Description of hazard
class
Safe under reason-
ably foreseeable con- tection normally af-
ditions
Low power; eye pro- Same as Class 2. Di- Direct intrabeam view- High power; diffused
rect intrabeam view- ing may be hazardous reflection may be haz-
forded by aversion
responses
ing with optical aids
may be hazardous
ardous
Protective housing
Required for each laser product; limits access necessary for performance of functions of the products
Safety interlock in pro-
tective housing
Designed to prevent removal of the panel until accessible emission values are below the AEL (see note 2) for the class
assigned
Remote control
Not required
Permits easy addition of external interlock in la-
ser installation
Key control
Not required
Not required
Laser inoperative when key is removed
Emission warning de-
vice
Gives audible or visible warning when laser is
switched on or if capacitor bank of pulsed laser
is being charged
Attenuator
Not required
Not required
Gives means beside ON/OFF switch to tempo-
rarily block beam
Location controls
Controls so located that there is no danger of exposure to AEL above
Classes 1 or 2 when adjustments are made.
Viewing optics
Scanning
Emission from all viewing systems must be below Class 1 AEL’s as applicable
Scan failure shall not cause product to exceed its classification
Class label
Required wording
Not required
Figures A and B and specified wording
Aperture label
Service entry label
Specified wording required
Required as appropriate to the class of accessible radiation
Override interlock label Required under certain conditions as appropriate to the class of laser used
User information Operation manuals must contain instructions for safe use
Purchasing and service Promotion brochures must reproduce classification labels; service manuals must contain safety information
information
Medical products
Special calibration instructions required
Special calibration instructions, means for
measurement and target-indicator required
Fibre optic
Cable service connections require tool to disconnect if disconnection breaks protective housing and permits access
above Class 1
*With respect to the requirements of remote interlock connector, key control, emission warning and attenuator, Class 3B laser products not
exceeding five times the AEL of Class 2 in the wavelength range of 400 nm to 700 nm are to be treated as Class 3A laser products.
Note 1. This table is intended to provide a convenient summary of requirements. See text of this standard for complete requirements.
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
17
2. AEL: Accessible Emission Limit
The maximum accessible emission level permitted within a particular class.
For your reference, see ANSI Z136.1-1993, Section 2.
Symbol and border: black
Background: yellow
Figure A Warning label - Hazard symbol
Legend and border: black
Background: yellow
Figure B Explanatory label
18
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
● FDA (Compliance Guide for Laser Products, 1985, according to 21 CFR1040.10)
Requirements
Class (see note 1)
II IIIa
I
IIa
IIIb
IV
Performance (all laser products)
Protective housing
R
R
R
R
R
R
(see note 2)
(see note 2)
(see note 2)
(see note 2)
(see note 2)
(see note 2)
Safety interlock
R (see notes 3, 4) R (see notes 3, 4) R (see notes 3, 4) R (see notes 3, 4) R (see notes 3, 4) R (see notes 3, 4)
Location of controls
Viewing optics
N/A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Scanning safeguard
R
Performance (laser systems)
Remote control connector N/A
N/A
N/A
N/A
N/A
N/A
R
N/A
N/A
R
R
R
R
R
Key control
N/A
N/A
Emission indicator
R
R
(see note 10)
(see note 10)
Beam attenuator
Reset
N/A
N/A
N/A
N/A
R
R
R
R
N/A
N/A
N/A
R
(see note 13)
Performance (specific purpose products)
Medical
S
S
S
S
S
S
S
S
S
S
S
S
(see note 8)
(see note 8)
(see note 8)
Surveying, leveling, align-
ment
S
NP
NP
Demonstration
S
S
S
(see note 11)
(see note 11)
Labeling (all laser products)
Certification & identifica-
tion
R
R
R
R
R
R
Protective housing
D
D
D
D
D
D
(see note 5)
(see note 5)
(see note 5)
(see note 5)
(see note 5)
(see note 5)
Aperture
N/A
N/A
N/A
R
R
R
R
Class warning
R
R
R
R
R
(see note 6)
(see note 7)
(see note 9)
(see note 12)
(see note 12)
Information (all laser products)
User information
Product literature
Service information
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
N/A
R
Abbreviations:
R: Required.
N/A: Not applicable.
S: Requirements: Same as for other products of that Class.
Also see footnotes.
NP: Not permitted.
D: Depends on level of interior radiation.
Footnotes:
1. Based on highest level accessible during operation.
2. Required wherever & whenever human access to laser radiation above Class I limits is not needed for product to perform its function.
3. Required for protective housings opened during operation or maintenance, if human access thus gained is not always necessary when
housing is open.
4. Interlock requirements vary according to Class of internal radiation.
5. Wording depends on level & wavelength of laser radiation within protective housing.
6. Warning statement label.
7. CAUTION logotype.
8. Requires means to measure level of laser radiation intended to irradiate the body.
9. CAUTION if 2.5 mW cm2 or less, DANGER if greater than 2.5 mW cm2.
10.Delay required between indication & emission.
11.Variance required for Class IIb or iV demonstration laser products and light shows.
12.DANGER logotype.
13.Required after August 20, 1986.
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
19
Use Precautions
● EN60825-1
Requirements;
Sub-clause
Classification
Class 3A
Class 1
Not required
Class 2
Class 3B*
Class 4
Remote interlock
Key control
Connect to room or door circuits
Remove key when not in use
Not required
Not required
Beam attenuator
When in use prevents inadvertent exposure
Indicates laser is energized
Emission indicator de- Not required
vice
Warning signs
Beam path
Not required
Follow precautions on warning signs
Not required
Terminate beam at end of useful length
Specular reflection
Eye protection
No requirements
No requirements
Prevent unintentional reflections
Required if engineering and administrative procedures not practicable
and MPE exceeded
Protective clothing
Training
No requirements
No requirements
Sometimes required
Specific requirements
Required for all operator and maintenance personnel
*With respect to the requirements of remote interlock connector, key control, beam attenuator, and emission indicator, Class 3B laser products not
exceeding five times the AEL of Class 2 in the wavelength range of 400 nm to 700 nm are to be treated as Class 3A laser products.
Note: This table is intended to provide a convenient summary of requirements. See text of this standard for complete precautions.
● ANSI Z136.1:1993 “American National Standard for the Safe Use of Lasers”
Control Measures for the Four Laser Classes
Control measures
Engineering Controls
Classification
1
2a
X
2
3a
X
3b
X
4
Protective Housing (4.3.1)
X
X
X
Without Protective Housing (4.3.1.1)
Interlocks on Protective Housing (4.3.2)
Service Access Panel (4.3.3)
Key Control (4.3.4)
LSO (see note 2) shall establish Alternate Controls
✩
✩
✩
✩
X
X
✩
✩
✩
✩
X
X
---
---
---
---
•
X
Viewing Portals (4.3.5.1)
---
---
MPE
MPE
---
MPE
MPE
---
MPE
MPE
MPE
MPE
Collecting Optics (4.3.5.2)
MPE
---
MPE
---
Totally Open Beam Path (4.3.6.1)
X
X
NHZ
NHZ
Limited Open Beam Path (4.3.6.2)
---
---
---
---
X
NHZ
X
NHZ
Enclosed Beam Path (4.3.6.3)
Remote Interlock Connector (4.3.7)
Beam Stop or Attenuator (4.3.8)
Activation Warning Systems (4.3.9)
Emission Delay (4.3.9.1)
None is required if 4.3.1 and 4.3.2 fulfilled
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
•
X
X
X
X
•
•
---
Indoor Laser Controlled Area (4.3.10)
X
X
NHZ
NHZ
Class 3b Laser Controlled Area (4.3.10.1)
Class 4 Laser Controlled Area (4.3.10.2)
Laser Outdoor Controls (4.3.11)
---
---
---
---
---
---
---
---
---
---
---
---
X
---
X
---
X
NHZ
X
NHZ
Laser in Navigable Airspace (4.3.11.2)
Temporary Laser Controlled Area (4.3.12)
---
---
---
•
•
•
✩
MPE
✩
MPE
✩
MPE
✩
MPE
---
---
Remote Firing & Monitoring (4.3.13)
Labels (4.3.14 and 4.7)
---
X
---
X
---
X
---
X
•
---
X
•
X
Area Posting (4.3.15)
---
---
---
X
X
NHZ
NHZ
Administrative & Procedural Controls
Standard Operating Procedures (4.4.1)
Output Emission Limitations (4.4.2)
Education and Training (4.4.3)
Authorized Personnel (4.4.4)
1
2a
---
---
---
---
---
2
3a
---
3b
•
4
---
---
---
---
---
---
---
•
X
LSO Determination
•
X
X
X
X
X
X
---
X
---
X
Alignment Procedures (4.4.5)
20
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
Control measures
Protective Equipment (4.4.6)
Classification
---
---
---
---
---
---
---
---
•
X
X
X
Spectator (4.4.7)
•
Service Personnel (4.4.8)
✩
✩
✩
✩
X
MPE
MPE
MPE
MPE
Demonstration with General Public (4.5.1)
Laser Optical Fiber Systems (4.5.2)
Laser Robotic Installations (4.5.3)
MPE ✝
MPE
---
---
X
X
X
X
X
X
MPE
---
MPE
---
MPE
---
X
NHZ
X
NHZ
Eye Protection (4.6.2)
---
---
---
---
---
---
---
---
•
X
MPE
MPE
Protective Windows (4.6.3)
X
X
NHZ
NHZ
Protective Barriers and Curtains (4.6.4)
Skin Protection (4.6.5)
---
---
---
---
---
---
---
---
•
•
X
MPE
X
MPE
Other Protective Equipment (4.6.5)
Use may be required
---
Warning Signs and Labels (4.7) (Design Requirements) ---
•
•
X
NHZ
X
NHZ
Service and Repairs (4.8)
LSO Determination
LSO Determination
Modification of Laser Systems (4.9)
Note 1. LEGEND
X:
•:
---:
✩:
Shall
Should
No requirement
Shall if enclosed Class 3b or Class 4
MPE: Shall if MPE is exceeded
NHZ: Nominal Hazard Zone analysis required
✝:
Applicable only to UV and IR Lasers (4.5.1.2)
2. LSO: Laser Safety Officer
An individual shall be designated the Laser Safety Officer with the authority and responsibility to monitor and enforce the control of laser
hazards, and to effect the knowledgeable evaluation and control of laser hazards.
For your reference, see ANSI Z136.1-1993, Section 1.3.
Laser Product Classifications
● EN
Class
Description
Class 1
Class 2
Lasers which are safe under reasonably foreseeable conditions of operation.
Lasers emitting visible radiation in the wavelength range from 400 nm to 700 nm. Eye protection is normally afforded by
aversion responses including the blink reflex.
Class 3A
Lasers which are safe for viewing with the unaided eye. For laser emitting in the wavelength range from 400 nm to 700 nm,
protection is afforded by aversion responses including the blink reflex. For other wavelengths the hazard to the unaided
eye is no greater than for Class 1. Direct intrabeam viewing of Class 3A lasers with optical aides (e.g., binoculars, tele-
scopes, microscopes) may be hazardous.
Class 3B
Class 4
Direct intrabeam viewing of these lasers is always hazardous. Viewing diffuse reflections is normally safe (see note).
Lasers which are also capable of producing hazardous diffuse reflections. They may cause skin injuries and could also
constitute a fire hazard. Their use requires extreme caution.
Note: Conditions for safe viewing of diffuse reflections for Class 3B visible lasers are: minimum viewing distance of 13 cm between screen and
cornea and a maximum viewing time of 10 s. Other viewing conditions require a comparison of the diffuse reflection exposure with the MPE.
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
21
Comparison of Classifications between FDA and ANSI
Class
Class I/1
FDA definition
ANSI description
Limits applicable to devices that have emissions in the ultraviolet, visi- A Class 1 laser is considered to be incapable of pro-
ble, and infrared spectra, and limits below which biological hazards
have not been established.
ducing damaging radiation levels during operation and
maintenance and is, therefore, exempt from any con-
trol measures or other forms of surveillance.
Class IIa/2a
Class II/2
Limits applicable to products whose visible emission does not exceed Class 2 lasers are divided into two subclasses, 2 and
Class I limits for emission durations of 1,000 seconds or less and are
not intended for viewing.
2a. A Class 2 laser emits in the visible portion of the
spectrum (0.4 to 0.7 µm) and eye protection is normal-
ly afforded by the aversion response including the blink
reflex.
Limits applicable to products that have emissions in the visible spectrum
(400 to 710 nm) for emission durations in excess of 0.25 second, pro-
viding that emissions for other durations and/or wavelengths do not ex-
ceed the Class I limits. Class II products are considered hazardous for
direct long-term ocular exposure.
Class IIIa/3a
Class IIIb/3b
Limits to products that have emissions in the visible spectrum and that Class 3 lasers are divided into two subclasses, 3a and
have beams where the total collectable radiant power does not exceed 3b. A Class 3 laser may be hazardous under direct and
5 milliwatts.
specular reflection viewing conditions, but the diffuse
reflection is usually not a hazard.
Limits applicable to devices that emit in the ultraviolet, visible, and infra-
red spectra. Class IIIb products include laser systems ranging from 5 to
500 milliwatts in the visible spectrum. Class IIIb emission levels are oc-
ular hazards for direct exposure throughout the range of the Class, and
skin hazards at the higher levels of the Class.
Class IV/4
Exceeding the limits of Class IIIb and are a hazard for scattered reflec- A Class 4 laser is a hazard to the eye or skin from the
tion as well as for direct exposure.
direct beam and sometimes from a diffuse reflection
and also can be a fire hazard. Class 4 lasers may also
produce laser-generated air contaminants and hazard-
ous plasma radiation.
Label Indications
● EN
EN/IEC warning label
Laser warning label
Explanatory label with specified wording
Note: Use of controls, adjustments, or procedures other than those specified herein may result in hazardous radiation exposure.
● FDA
Aperture Label
Class II Caution logo type
Certification and
identification label
Caution
logo type
Aperture label
Certification and Identification Label
Note: Use of controls, adjustments, or procedures other than those specified herein may result in hazardous radiation exposure.
22
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
Dimensions
(Unit: mm)
■ Sensor Heads (Diffuse Reflective)
ZX-LD40
ZX-LD100
ZX-LD300
ZX-LD40L
ZX-LD100L
ZX-LD300L
17
16.6
12.4
Two 3.2-dia. mounting
holes
Mounting Holes
Two, M3 holes
L ∗
33
7
Measurement
point
1.8
3.5
Reference
surface
5
7
14.8
3.4
A ∗
Emitter axis
Lens: 5 dia.
30.05
32
31.1
0.1
32
Receiver axis
Range
indicators
39
7
Lens: 8 dia.
0.1
3.5
7
26
24.05
26
Connector
15 dia.
46
Vinyl-insulated round cable, 5.1 dia.,
Standard: 500 mm
∗
ZX-LD40L: L = 40 mm, A = 23°
ZX-LD10L: L = 100 mm, A = 11°
ZX-LD30L: L = 300 mm, A = 3.8°
■ Sensor Heads (Regular Reflective)
14
ZX-LD30V
4.8
ZX-LD30VL
25 8.6
Vinyl-insulated round cable,
5.1 dia., Standard: 0.5 m
5-R2
20.7
42.7
Connector
Mounting Holes
45
1
1
32.7
30
Two, M4 holes
4.75
4.75
46
9.5
9.2
0.1
47
35°
12.5
Light axis
Two, 4.5-dia.
15 dia.
mounting holes
Emitter
axis
Receiver
axis
47
55
Reference plain
Measurement center
Lens (10 dia.)
Lens (16 dia.)
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
23
■ Sensor Heads (Through-beam)
ZX-LT001
ZX-LT005
Emitter
Receiver
Two, 3.2 dia.
34
Two, 3.2 dia.
19 2.8
Vinyl-insulated round
cable (gray), 2.6 dia.,
Standard: 500 mm
2.8
Vinyl-insulated round cable (black),
2.6 dia., Standard: 500 mm
5
16
9
15
15
9
Connector
Connector
Laser ON indicator
Light axis center
15
Light axis center
15
Slit (1 x 5) (Only for ZX-LT005)
Mounting Holes
Mounting Holes
0.1
0.1
9
9
Two, M3 holes
Two, M3 holes
Sensor Head-Amplifier Unit
Connecting Cable (Provided)
1,500+200
0
46
15 dia.
Connector
Connector
2.6 dia × 2
Receiver
Two, 3.2 dia.
Emitter
ZX-LT010
Two, 3.2 dia.
Vinyl-insulated round
cable (gray), 2.6 dia.,
Standard: 500 mm
2.8
42
22
25
2.8
Vinyl-insulated round cable (black),
2.6 dia., Standard: 500 mm
10
14 20
20 14
Connector
Connector
Light axis center
Laser ON indicator
Light axis center
20
20
Slit (1 x 10)
Mounting Holes
Mounting Holes
14 0.1
14 0.1
Two, M3 holes
Two, M3 holes
Sensor Head-Amplifier Unit
Connecting Cable (Provided)
1,500+200
0
46
15 dia.
Connector
Connector
2.6 dia × 2
24
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
ZX-LT030
Receiver
Emitter
70
50
70
50
Two, 4.5 dia.
Two, 4.5 dia.
10
10
16
16
10
10
22.6
22.6
Vinyl insulated
round cable, 4 dia.,
Standard length: 0.5 m
Vinyl insulated round
cable, 4 dia.,
Standard length: 0.5 m
68
1
1
52
Three, M4 x 25
+ pan head screw
Three, M4 x 25
+ pan head screw
44
44
70
70
69
69
41
41
4.75
4.75
21
21
12.5
12.5
9
9
10
5
44
60
10
2.3
5
2.3
Connector
Connector
Lens (8 x 36)
10
9.5
Slit (1 x 30)
Two, M3,
Two, M3, depth: 5
35.9
18
depth: 5
35
43
6
6
8.1
8.1
20
20
Two, M4
Two, M4
11.5 dia.
14.7 dia.
50
50
Sensor Head - Amplifier Unit
Connection Cable
35.3
1500+50
0
46
11 dia.
15 dia.
43
13.2 dia.
■ Amplifier Units
ZX-LDA11-N
ZX-LDA41-N
133
44
4.2
3
64.3
4.2
30
31.5
15.8
15.5 dia.
13.2
13
36.8
Vinyl-insulated round cable, 5.23 dia.
Standard: 100 mm
Vinyl-insulated round cable, 5.2 dia. (conductor
cross-section: 0.09 mm2, 10-conductor insulator
diameter: 0.7 mm), Standard: 2 m
11.7
11.7
2.2
29
Current/voltage output selector switch
(set to voltage output when shipped)
Voltage output
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
25
■ Accessories (Order Separately)
Operation
indicators
Calculating Unit
Connectors
24.9
19.5
ZX-CAL2
3
57
15.1
12
8
54.9
44.05
9.5
30
15
26
14.4
5
36.7
3.4
Side-view Attachments
ZX-XF12
15
Light axis center
Two, 2.2 dia.
15 10.6
15
15
2.7
ZX-XF22
20
Light axis center
Two, 2.2 dia.
20
21
Seal
20
2.8
26
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
ZX-series Communications Interface Unit
ZX-SF11
Coupling connector
Sensor communications indicator (communications operation)
Sensor communications indicator (communications error)
External terminal communications
indicator (communications operation)
Power supply indicator
External terminal communications
indicator (communications error)
4.2
64.3
4.2
30
3
(336)
(46)
31.5
15
13
36.8
13.2
Vinyl-insulated round cable, 5.23 dia.
Standard: 100 mm
11.7
(33.1)
11.7
3
5
6.55
Connector
Cables with Connectors on Both
Ends (for Extension)
46
✽
44
ZX-XC1A (1 m)
ZX-XC4A (4 m)
15.5 dia.
15 dia.
ZX-XC8A (8 m)
ZX-XC9A (9 m)
Vinyl-insulated round cable, 5.2 dia.,
10 conductors
12 pins (male)
12 pins (female)
∗ ZX-XC1A: 1,000
ZX-XC4A: 4,000
ZX-XC8A: 8,000
ZX-XC9A: 9,000
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
27
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
This document provides information mainly for selecting suitable models. Please read the document Z197 carefully for
information that the user must understand and accept before purchase, including information on warranty, limitations of
liability, and precautions.
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
Sensing Devices Division H.Q.
Application Sensors Division
Shiokoji Horikawa, Shimogyo-ku,
Kyoto, 600-8530 Japan
Tel: (81)75-344-7068/Fax: (81)75-344-7107
Read and Understand This Catalog
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or
comments.
Warranty and Limitations of Liability
WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if
specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE
HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS, OR COMMERCIAL
LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR
STRICT LIABILITY.
In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's
application or use of the product.
At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the
products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product,
machine, system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible
uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.
• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to separate industry or government regulations.
• Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Disclaimers
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the product may be changed without any notice. When in doubt, special model numbers may be assigned to fix
or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual
specifications of purchased product.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
ERRORS AND OMISSIONS
The information in this catalog has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent
the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON
Warranty and Limitations of Liability.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
COPYRIGHT AND COPY PERMISSION
This catalog shall not be copied for sales or promotions without permission.
This catalog is protected by copyright and is intended solely for use in conjunction with the product. Please notify us before copying or reproducing this
catalog in any manner, for any other purpose. If copying or transmitting this catalog to another, please copy or transmit it in its entirety.
2008.4
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2008 All Rights Reserved.
相关型号：
ZX05-1-S+
Double Balanced Mixer, 0.5MHz Min, 500MHz Max, 7.8dB Conversion Loss-Max, ROHS COMPLIANT, CASE FL905
MINI
ZX05-10+
Double Balanced Mixer, 10MHz Min, 1000MHz Max, 8.3dB Conversion Loss-Max, ROHS COMPLIANT, CASE FL905
MINI
ZX05-10-S+
Double Balanced Mixer, 10MHz Min, 1000MHz Max, 8.3dB Conversion Loss-Max, ROHS COMPLIANT, CASE FL905
MINI
ZX05-10H-S
Double Balanced Mixer, 10MHz Min, 1000MHz Max, 9.5dB Conversion Loss-Max, CASE FL905
MINI
ZX05-10H-S+
Double Balanced Mixer, 10MHz Min, 1000MHz Max, 9.5dB Conversion Loss-Max, ROHS COMPLIANT, CASE FL905
MINI
©2020 ICPDF网 联系我们和版权申明