G3MC-101PL-VD-DC5 [OMRON]
Trigger Output SSR, 1-Channel, 2500V Isolation, COMPACT PACKAGE-4;型号: | G3MC-101PL-VD-DC5 |
厂家: | OMRON ELECTRONICS LLC |
描述: | Trigger Output SSR, 1-Channel, 2500V Isolation, COMPACT PACKAGE-4 输出元件 光电 |
文件: | 总6页 (文件大小:465K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Solid State Relay
G3MC
Compact, Thin-profile, Low-cost SSR with
Reinforced Insulation
• Small bottom surface area (approx. 80% of the
conventional G3MB’s), ideal for close PCB mounting.
•
DC input and AC output for an applicable load of 1A at 40°C.
• Compact, thin-profile SSR of monoblock construction with
an all-in-one frame incorporates a PCB, terminals, and a
heatsink.
• Approved by UL and CSA. VDE certified models available.
• Models with reinforced insulation are available.
Ordering Information
To Order: Select the part number and add the desired coil voltage rating, (e.g., G3MC-101P-DC12).
Isolation
Zero-cross function
Yes
Built-in snubber circuit
Yes
Rated output load
Rated input voltage
5 VDC
Part number
G3MC-101P
Phototriac
1 A at 100 to 120 VAC
(75 to 132 VAC)
12 VDC
24 VDC
5 VDC
No
Yes
No
G3MC-101PL
G3MC-202P
G3MC-202PL
12 VDC
24 VDC
5 VDC
2 A at 100 to 240 VAC
(75 to 264 VAC)
12 VDC
24 VDC
5 VDC
12 VDC
24 VDC
Note: 1. All models meet UL and CSA standards. In order to obtain VDE approved versions with UL, CSA and VDE Logos, add “-VD” to the part
number. Example: G3MC-101P-VD-DC12
2. 2A models are available with reinforced insulation. Add “-1” to the part number to obain 2A models with reinfored insulation.
Examples: G3MC-202PL-1-DC5
G3MC-202P-VD-1-DC24
Solid State Relay G3MC
401
Specifications
■ Ratings (Ambient temperature 25°C)
Input
Rated voltage
Operating voltage
Impedance
Voltage levels
Must operate voltage
Must dropout voltage
5 VDC
4 to 6 VDC
300Ω 20%
4 VDC max.
1 VDC min.
12 VDC
24 VDC
9.6 to 14.4 VDC
19.2 to 28.8 VDC
800Ω 20%
1.6kΩ 20%
9.6 VDC max.
19.2 VDC max.
Note: Each model has 5-VDC, 12-VDC, and 24-VDC input versions.
Output
Part number
Applicable load
Load voltage range Load current
Rated load voltage
Surge current
8 A (60 Hz, 1 cycle)
30 A (60 Hz, 1 cycle)
G3MC-101P(L)(-VD)
100 to 120 VAC, 50/60 Hz 75 to 132 VAC, 50/60 Hz
100 to 240 VAC, 50/60 Hz 75 to 264 VAC, 50/60 Hz
0.1 to 1 A
0.1 to 2 A
G3MC-202P(L)(-VD)(-1)
■ Characteristics
Item
G3MC-101P(-VD)
G3MC-101PL(-VD)
1 ms max.
G3MC-202P(-VD)(-1)
G3MC-202PL(-VD)(-1)
Operate time
1/2 of load power source
cycle + 1 ms
1/2 of load power source
cycle + 1 ms
1 ms max.
Release time
1/2 of load power source cycle + 1 ms)
Output ON voltage drop 1.6 V (RMS) max.
Leakage current
1 mA max. (at 100 VAC)
1,000 MΩ min. (at 500 VDC)
1.5 mA max. (at 200 VAC)
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
2,500 VAC, 50/60 Hz for 1 min (3,000 VAC, 50/60 Hz for 1 min. for G3MC-@@@-VD-1)
Malfunction: 10 to 55 Hz, 0.75-mm double amplitude
Malfunction: 1,000 m/s2 (approx. 100G)
Ambient temperature
Operating:–30°C to 80°C (with no icing or condensation)
Storage:–30°C to 100°C (with no icing or condensation)
Approved standards
UL File No. E64562, CSA File No. LR35535
EN60950 File No. 5925UG (“-VD(-1)” type)
Ambient humidity
Weight
Operating: 45% to 85%
Approx. 2.5g (Approx. 5g for G3MC-202P(L)-VD-1)
402
Solid State Relay G3MC
Engineering Data
■ G3MC-101P(L)(-VD)
Load Current vs. Ambient
Temperature Characteristics
Inrush Current Resistivity
One cycle, non-repetitive (Keep the inrush current
to half the rated value if it occurs repeatedly.)
1.2
1.0
0.8
0.6
0.4
0.2
0
−30 −20
0
20
40
60
80
100
Energized time (ms)
Ambient temperature (°C)
■ G3MC-202P(L)(-VD)(-1)
Load Current vs. Ambient
Inrush Current Resistivity
Temperature Characteristics
One cycle, non-repetitive (Keep the inrush current
to half the rated value if it occurs repeatedly.)
2.5
2.0
1.5
1.0
0.5
0
−30 −20
0
20 25 40
60
80 100
Ambient temperature (°C)
Energized time (ms)
Solid State Relay G3MC
403
Dimensions
Units: mm (inch)
G3MC-101P(L)(-VD)
PCB Dimensions
(Bottom View)
Four, 1.0-dia. holes
4.5 max.
24.5 max.
13.5 max.
0.8
3.5
2.54
10.16
0.25
1.2
Terminal Arrangement
(Bottom View)
4-1.6
4-0.7
7.62
2.54
G3MC-202P(L)(-VD)(-1)
PCB Dimensions
(Bottom View)
4.5 max.
24.5 max.
Four, 1.0-dia. holes
20.5 max.
0.8
3.5
Terminal Arrangement
(Bottom View)
2.54
10.16
0.25
1.2
4-1.6
4-0.7
7.62
2.54
404
Solid State Relay G3MC
Precautions
■ General Precautions
Do not touch the terminals of the SSR while power is being supplied
to the SSR. The terminals are charged with the power,
and an electric shock may be received by touching the terminals.
■ Protective element
No overvoltage absorption element is built in. Therefore, if the G3MC
is connected to an inductive load, be sure to connect the overvoltage
absorption element.
The built-in capacitor may have a residual voltage after the SSR
is turned off. Be sure to discharge the residual voltage before touch-
ing the terminals of the SSR, otherwise an electric shock
may be received.
■ Mounting
G3MC-@@@PL (without Zero cross function)
1. Make sure that no excessive voltage or current is imposed on or
Phototriac
flows to the input or output circuit of the SSR,
otherwise the SSR may malfunction or burn.
2. Solder the terminals of the SSR properly under the required sol-
dering conditions. The SSR may be abnormally heated and burn
if power is supplied to the terminals soldered incorrectly.
Load
Protective
element
(MOV)
Input
Power
supply
3. Do not short-circuit the load of the SSR while power is supplied to
the SSR. Do not short-circuit the power supply through the SSR.
The SSR may be damaged, malfunction, or burn if the load or
power supply is short-circuited.
G3MC-@@@P (with Zero cross function)
Phototriac
■ Correct use
Load
Protective
element
(MOV)
Power
supply
Input
The terminals of the SSR are highly heat-conductive. Each terminal
must be soldered within 10 s at 260°C or within 5 s at 350°C.
The SSR is of a thin-profile construction. To maintain the vibration
resistance of the SSR, make sure that the space between the SSR
and PCB is 0.1 mm maximum. Lifting of the PCB can be prevented
by setting the hole diameter of the PCBs on both sides slightly
smaller than the actual terminal dimension.
Select the model without the zero-cross function when using the Unit
for phase control output.
The casing works as a heat sink. When mounting two or more Units
closely, make sure that the Units are properly ventilated by taking
ambient temperature rises into consideration. If Units are closely
mounted and used in places with no ventilation, the load current of
each Unit must be 1/2 of the rated load current.
Solid State Relay G3MC
405
All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which
can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
OMRON ON-LINE
Global - http://www.omron.com
USA - http://www.components.omron.com
OMRON ELECTRONIC
COMPONENTS LLC
55 E. Commerce Drive, Suite B
Schaumburg, IL 60173
847-882-2288
09/11
Specifications subject to change without notice
Printed in USA
Cat. No. X301-E-1b
Solid State Relay G3MC
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明