E2EZ-X4Y12M [OMRON]
Chip-immune Inductive Proximity Sensor;
| 型号： | E2EZ-X4Y12M |
| 厂家： | 
OMRON ELECTRONICS LLC |
| 描述： | Chip-immune Inductive Proximity Sensor |
| 文件： | 总9页 (文件大小：840K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Chip-immune Inductive Proximity Sensor
E2EZ
CSM_E2EZ_DS_E_6_1
Chip-immune Inductive
Proximity Sensor
• Correct operation even with aluminum or iron chips sticking
to the Sensor.
Only the sensing object is detected.
• Pre-wired Smartclick Connector Models also available.
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Be sure to read Safety Precautions on
page 7.
Ordering Information
Sensors [Refer to Dimensions on page 8.]
Pre-wired Models
Model
Appearance
M12
Sensing distance
Output configuration
Operation mode
NO
NC
DC 2-Wire Models
E2EZ-X2D1-N 2M
E2EZ-X4C1 2M
E2EZ-X4D1-N 2M
E2EZ-X4Y1 2M
E2EZ-X8C1 2M
E2EZ-X8D1-N 2M
E2EZ-X8Y1 2M
E2EZ-X2D2-N 2M
2 mm
DC 3-wire, NPN
DC 2-wire
—
M18
E2EZ-X4D2-N 2M
4 mm
Shielded
AC 2-wire
—
—
DC 3-wire, NPN
DC 2-wire
M30
E2EZ-X8D2-N 2M
8 mm
AC 2-wire
Pre-wired Smartclick Connector Models (M12)
Model
Operation mode
Appearance
Sensing distance
Output configuration
NO
NC
—
—
—
—
—
—
DC 2-wire, (3)-(4) pin arrangement
DC 2-wire, (1)-(4) pin arrangement
DC 2-wire, (3)-(4) pin arrangement
DC 2-wire, (1)-(4) pin arrangement
DC 2-wire, (3)-(4) pin arrangement
DC 2-wire, (1)-(4) pin arrangement
E2EZ-X2D1-M1TJ 0.3M
E2EZ-X2D1-M1TGJ 0.3M
E2EZ-X4D1-M1TJ 0.3M
E2EZ-X4D1-M1TGJ 0.3M
E2EZ-X8D1-M1TJ 0.3M
E2EZ-X8D1-M1TGJ 0.3M
M12
2 mm
Shielded
M18
M30
4 mm
8 mm
1
E2EZ
Pre-wired Connector Models (M12)
Model
Appearance
Sensing distance
Output configuration
Operation mode
NO
NC
DC 2-wire, (3)-(4) pin arrangement
DC 2-wire, (1)-(4) pin arrangement
DC 2-wire, (3)-(4) pin arrangement
DC 2-wire, (1)-(4) pin arrangement
DC 2-wire, (3)-(4) pin arrangement
DC 2-wire, (1)-(4) pin arrangement
E2EZ-X2D1-M1J 0.3M
E2EZ-X2D1-M1GJ 0.3M
E2EZ-X4D1-M1J 0.3M
E2EZ-X4D1-M1GJ 0.3M
E2EZ-X8D1-M1J 0.3M
E2EZ-X8D1-M1GJ 0.3M
—
—
—
—
—
—
M12
2 mm
Shielded
M18
M30
4 mm
8 mm
Accessories (Order Separately)
Sensor I/O Connectors (M12, Sockets on One Cable End)
(Models for Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) [Refer to Dimensions on XS2, XS5.]
Appearance
Straight
Cable length
Sensor I/O Connector model number
XS2F-D421-DD0
Applicable Proximity Sensor model number
2 m
5 m
2 m
5 m
2 m
XS2F-D421-GD0
XS2F-D422-DD0
XS2F-D422-GD0
XS2F-D421-DA0-F
E2EZ-X@D1-M1J
L-shape
Straight
5 m
2 m
5 m
XS2F-D421-GA0-F
XS2F-D422-DA0-F
XS2F-D422-GA0-F
E2EZ-X@D1-M1GJ
L-shape
2 m
5 m
XS5F-D421-D80-F
XS5F-D421-G80-F
Smartclick
Connector
Straight
E2EZ-X@D1-M1TJ
E2EZ-X@D1-M1TGJ
Mounting Brackets
Protective Covers
Sputter Protective Covers
Refer to Y92@ for details.
2
E2EZ
Ratings and Specifications
Model E2EZ-X2D@-N
E2EZ-X2D@-M1J
E2EZ-X4D@-N
E2EZ-X8D@-N
E2EZ-X4C1
E2EZ-X4Y1
E2EZ-X8C1
E2EZ-X8Y1
E2EZ-X4D@-M1J
E2EZ-X4D@-M1GJ
E2EZ-X8D@-M1J
E2EZ-X8D@-M1GJ
Item
E2EZ-X2D@-M1GJ
2 mm 10%
Sensing distance
Set distance *1
Differential travel
Detectable object
4 mm 10%
0 to 3.2 mm
8 mm 10%
0 to 6.4 mm
4 mm 10%
0 to 3.2 mm
8 mm 10%
0 to 6.4 mm
0 to 1.6 mm
20% max. of sensing distance
Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 4.)
Standard sensing
object
Iron, 12 × 12 × 1 mm
Iron, 30 × 30 × 1 mm
Iron, 54 × 54 × 1 mm
Iron, 30 × 30 × 1 mm
Iron, 54 × 54 × 1 mm
Response
C Models: 12 Hz
Y Models: 5 Hz
C Models: 8 Hz
Y Models: 5 Hz
200 Hz
100 Hz
30 Hz
frequency *2
Power supply volt-
age
(operating voltage
range)
C Models: 12 to 24 VDC (10 to 30 VDC), ripple (p-p):
10% max.
Y Models: 100 to 220 VAC (90 to 250 VAC), 50/60 Hz
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
Current
consumption
---
C Models: 15 mA max.
Leakage current
0.8 mA max.
Y Models: 2 mA max. at 100 VAC, 3 mA max. at 200 VAC
C Models: NPN open-collector output
100 mA max. at 12 VDC (30 VDC max.)
200 mA max. at 24 VDC (30 VDC max.)
Y Models: 10 to 200 mA
Load cur-
rent
3 to 100 mA max.
Con-
trol
C Models: 2 V max. (Load current: 200 mA, Cable length:
output
Residual
voltage
2 m)
3 V max. (Load current: 100 mA, Cable length: 2 m)
Y Models: Refer to residual voltage characteristic data
Refer to page 4.
D1 Models: Operation indicator (red), Setting indicator (green)
D2 Models: Operation indicator (red)
C Models: Detection indicator (red)
Y Models: Operation indicator (red)
Indicators
Operation mode
(with sensing ob-
ject approaching)
D1 Models: NO
NO
D2 Models: NC
For details, refer to the Timing chart on page 6.
For details, refer to the Timing chart on page 5.
C Models: Load short-circuit protection, Reverse polarity
protection, Surge suppressor
Y Models: Surge suppressor
Protection
circuits
Load short-circuit protection, Surge suppressor
Ambient
temperature range
Operating/Storage: 0 to 50°C (with no icing or condensation)
Ambient
humidity range
Operating/Storage: 35% to 95% (with no condensation)
Temperature
influence
20% max. of sensing distance at 23°C in the temperature range of 0 to 50°C
2.5% max. of sensing distance at rated voltage in the rated voltage 10% range
50 MΩ min. (at 500 VDC) between current-carrying parts and case
Voltage influence
Insulation
resistance
C Models: 1,000 VAC, 50/60 Hz for 1 min between cur-
rent-carrying parts and case
Y Models: 2,000 VAC, 50/60 Hz for 1 min between cur-
rent-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
Vibration
Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
IEC 60529 IP67, in-house standards: oil-resistant
resistance
Shock resistance
Degree of
protection
Connection
method
Pre-wired Models (Standard cable length: 2 m) and Pre-wired Connector Models
E2EZ-X2D@-N: Approx.
E2EZ-X4D@-N: Approx.
E2EZ-X8D@-N: Approx.
220 g
70 g
160 g
Weight
(packed state)
E2EZ-X2D@-M1J: Approx. E2EZ-X4D@-M1J:
E2EZ-X8D@-M1J:
Approx. 170 g
Approx. 270 g
40 g
Approx. 90 g
E2EZ-X4D@-M1GJ:
Approx. 90 g
Approx. 160 g
E2EZ-X8D@-M1GJ:
Approx. 160 g
E2EZ-X2D@-M1GJ:
Approx. 40 g
Case
Nickel-plated brass
PBT
Sensing
surface
Heat-resistant ABS
Materi-
als
Clamp-
ing nuts
Zinc-plated iron
Toothed
washer
Zinc-plated iron
Accessories
Instruction manual
*1. Use the Sensor within the range in which the green indicator is ON.
*2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and
a set distance of half the sensing distance.
3
E2EZ
Engineering Data (Reference Value)
Sensing Area
E2EZ-X2@
E2EZ-X4@
E2EZ-X8@
5
10
2.5
9
4
2.0
8
7
Y
Y
Y
3
1.5
1.0
6
X
X
X
5
4
3
2
1
0
0.5
0.0
2
1
0
−10 −8 −6 −4 −2
0
2
4
6
8
10
−8
−6
−4
−2
0
2
4
6
8
−20 −16 −12 −8 −4
0
4
8
12 16 20
Distance Y
Distance Y
(mm)
Distance Y
(mm)
Sensing Head
Sensing Head
Sensing Head
(mm)
Influence of Sensing Object Size and Material
E2EZ-X2@
E2EZ-X4@
E2EZ-X8@
5
10
10
d ×
d ×
d ×
d
d
d
Iron
t = 1 mm
t = 1 mm
t = 1 mm
X
X
X
4
3
2
1
8
8
6
4
2
Brass
6
4
2
Stainless steel
(SUS304)
Iron
Aluminum
Iron
Brass
Brass
Aluminum
Copper
Stainless
steel
(SUS304)
Aluminum
Copper
40
Stainless
steel
(SUS304)
0
10
20
30
40
0
10
20
30
50
60
0
10
20
30
40
50
60
Side length of sensing object: d (mm)
Side length of sensing object: d (mm)
Side length of sensing object: d (mm)
Residual Output Voltage
E2EZ-X@D@-N
E2EZ-X4Y1/-X8Y1 at 100 VAC
E2EZ-X4Y1/-X8Y1 at 200 VAC
5
Residual output
voltage
Residual output
voltage
ON
4
3
2
100
200
ON
V
150
V
100 VAC
50
A
100
200 VAC
A
1
0
50
0
Residual
load
Residual load
voltage
OFF
voltage
OFF
1
3
5
10
30 50 100
300500 1,000
0
5
10
50
100 150 200
5
10
50
100 150 200
Load current (mA)
Load current (mA)
Load current (mA)
4
E2EZ
Leakage Current
E2EZ-X4Y1/-X8Y1
E2EZ-X@D@-N
1.5
Protective
resistance
A
6
5
4
3
2
1
AC power
1.0
0.5
90 100
150
200
250
0
10
20
30
40
Power supply voltage (V)
Power supply voltage (V)
I/O Circuit Diagrams
DC 2-Wire Models
Opera-
tion
Model
Timing chart
Output circuit
mode
Load
+V
Brown
Prox-
imity
Sensor
main
E2EZ-X2D1-N
E2EZ-X4D1-N
E2EZ-X8D1-N
circuit
0 V
Blue
Note: The load can be connected to either the
+V or 0 V side.
Set position
Unstable
sensing
area
Non-sensing
area
Stable sensing area
(M1J)
Connector Pin
Arrangement
Sensing
object
4
Load
+V
Prox-
imity
Sensor
main
circuit
1
100 80(TYP)
Rated sensing
0
(%)
NO
2
4
ON
3
Setting indicator
(green)
distance
OFF
ON
E2EZ-X2D1-M1J
E2EZ-X2D1-M1GJ
E2EZ-X4D1-M1J
E2EZ-X4D1-M1GJ
E2EZ-X8D1-M1J
E2EZ-X8D1-M1GJ
Note: Pins 1 and 2
are not used.
3
Operation
indicator (red)
0 V
OFF
ON
Note: The load can be connected to either the +V or 0 V side.
Control output
OFF
(M1GJ)
Connector Pin
Arrangement
1
4
Load
+V
Prox-
imity
Sensor
main
1
2
4
3
circuit
Note: Pins 2 and 3
are not used.
0 V
Note: The load can be connected to either the +V or 0 V side.
Non-sensing area
Sensing area
Load
+V
Sensing
object
Brown
Prox-
imity
Sensor
main
circuit
E2EZ-X2D2-N
E2EZ-X4D2-N
E2EZ-X8D2-N
100
Rated sensing
distance
0
(%)
NC
ON
Operation
indicator (Red)
0 V
Blue
OFF
ON
Note: The load can be connected to either the
+V or 0 V side.
Control output
OFF
5
E2EZ
DC 3-wire Models
Operation
mode
Model
Timing chart
Output circuit
Brown
+V
Present
Not present
Operate
Reset
Load
Sensing object
Load
Proximity
Sensor
main
*
Black
E2EZ-X4C1
E2EZ-X8C1
Output
NO
2.2 Ω
circuit
ON
Blue
Detection indicator (red)
0 V
OFF
* 100 mA max. at 12 V, 200 mA max. at 24 V
(load current).
AC 2-Wire Models
Operation
Model
Timing chart
Output circuit
mode
Brown
Load
Present
Not present
Operate
Reset
Sensing object
Load
Prox-
imity
Sensor
main
E2EZ-X4Y1
E2EZ-X8Y1
NO
circuit
Blue
ON
Operation indicator (red)
OFF
Connections for Sensor I/O Connectors
Proximity Sensor
Sensor I/O Connectors
Model
Connections
Operation
mode
Model
Model
1: Straight
2: L-shape
E2EZ
E2EZ
E2EZ
E2EZ
XS2F
1
2
3
4
1
2
3
4
Brown (+)
DC 2-Wire Models
(IEC pin wiring)
E2EZ-X@D1-M1GJ
E2EZ-X@D1-M1J
E2EZ-X@D1-M1TGJ
E2EZ-X@D1-M1TJ
XS2F-D42@-@A0-F
Blue (−)
D: 2-m cable
G: 5-m cable
1: Straight
2: L-shape
XS2F
DC 2-Wire Models
(previous pin wir-
ing)
1
2
3
4
1
2
3
4
XS2F-D42@-@D0
Blue (−)
Brown (+)
D: 2-m cable
G: 5-m cable
NO
XS5F
1
2
3
4
1
2
3
4
Brown (+)
White
Blue
DC 2-Wire Models
(IEC pin wiring)
Black (−)
XS5F-D421-@80-F
XS5F
D: 2-m cable
G: 5-m cable
DC 2-Wire Models
(previous pin wir-
ing)
1
2
3
4
1
2
3
4
Brown
White
Blue (−)
Black (+)
Refer to Introduction to Sensor I/O Connectors/Sensor Controllers for details.
6
E2EZ
Safety Precautions
Refer to Warranty and Limitations of Liability.
WARNING
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
Aluminum and Iron Cuttings
Normally aluminum or iron cuttings will not be detected even if they
adhere to or accumulate on the sensing surface.
Detection signals may be output for the following:
If this occurs, remove the cuttings from the sensing surface.
1. Relationship between the Size of the Cutting (d) and the Size of
the Sensing Surface (D)
Precautions for Correct Use
Do not use this product under ambient conditions that exceed the
ratings.
2
3
Cuttings of the size d ≥
D on the sensing surface *
● Design
Cuttings of the size d* (Unit: mm)
d
Influence of Surrounding Metal
Model
Size
D
10 *
16
Cutting
When mounting the Sensor within a metal panel, ensure that the
clearances given in the following table are maintained. Failure to
maintain these distances may cause deterioration in the performance
of the Sensor.
E2EZ-X2@
E2EZ-X4@
E2EZ-X8@
Sensing
surface
D
28
1
3
* E2EZ-X2@: d ≥
D on the sensing surface.
m
2. Cuttings Pressed against the Sensing
Surface
n
d dia.
Pressed against
sensing surface.
D
Cutting
l
Influence of Surrounding Metal (Unit: mm)
Item
l
d
D
m
n
Embedded
material
Model
Iron
Aluminum
Iron
0
2
12
25
18
40
30
70
0
2
18
36
27
54
45
90
● Mounting
E2EZ-X2@
8
Do not tighten the nut with excessive force.
A washer must be used with the nut.
0
0
E2EZ-X4@
E2EZ-X8@
16
32
Aluminum
Iron
5
5
0
0
Aluminum
10
10
Mutual Interference
Part B Part A
When installing Sensors face-to-face or side-by-side, ensure that the
minimum distances given in the following table are maintained.
Note: 1. The allowable tightening strength depends on the distance from the
edge of the head, as shown in the following table. (A is the distance
from the edge of the head. B includes the nut on the head side. If the
edge of the nut is in part A, the tightening torque for part A applies
instead.)
Mutual Interference (Unit: mm)
Model
Item
A
B
20
2. The following torque assume washers are being used.
A
B
E2EZ-X2@
E2EZ-X4@
E2EZ-X8@
30
40
60
Tightening
Part A
Part B
Torque
50
Dimension
100
Torque
Torque
Model
(mm)
E2EZ-X2D@-@
E2EZ-X4D@-@
E2EZ-X8D@-@
30 N·m
70 N·m
180 N·m
E2EZ-X4C1
E2EZ-X4Y1
20
22
15 N·m
29 N·m
29 N·m
39 N·m
E2EZ-X8C1
E2EZ-X8Y1
7
E2EZ
(Unit: mm)
Dimensions
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
E2EZ-X2D@-N
38
33
9
Pre-wired Connector Models (-M1J/M1GJ)
21 dia.
17
4
10
M12 × 1
15 dia.
*1
Indicator*2
4-dia. vinyl-insulated round cable with
2 conductors (Conductor cross
M12 × 1
Two clamping nuts
Toothed washer
section: 0.3 mm2, Insulator diameter:
1.3 mm), Standard length: 300 mm
*1. 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2,
Insulator diameter: 1.3 mm), Standard length: 2 m
*2. D1 Models: Operation indicator (red), Setting indicator (green), D2 Models: Operation
indicator (red)
E2EZ-X8D@-N
E2EZ-X4D@-N
48
43
12
42 dia.
43
38
12
29 dia.
24
36
5
10
4
10
*1
*1
Indicator*2
*1. 6-dia. vinyl-insulated round cable with 2 conduc-
tors (Conductor cross section: 0.5 mm2, Insula-
tor diameter: 1.9 mm), Standard length: 2 m
The cable can be extended up to 200 m (sepa-
rate metal conduit).
Indicator*2
M18 × 1
Two clamping nuts
Toothed washer
*1. 6-dia. vinyl-insulated round cable with 2 con-
ductors (Conductor cross section: 0.5 mm2, In-
sulator diameter: 1.9 mm), Standard length: 2 m
The cable can be extended up to 200 m (sepa-
rate metal conduit).
*2. D1 Models: Operation indicator (red), Setting
indicator (green)
M30 × 1.5
Two clamping nuts
Toothed washer
*2. D1 Models: Operation indicator (red), Setting in-
dicator (green)
D2 Models: Operation indicator (red)
D2 Models: Operation indicator (red)
Pre-wired Connector Models (-M1J/M1GJ)
Pre-wired Connector Models (-M1J/M1GJ)
M12 × 1
15 dia.
M12 × 1
15 dia.
6-dia. vinyl-insulated round cable with
2 conductors (Conductor cross section:
0.5 mm2, Insulator diameter: 1.9 mm),
Standard length: 300 mm
6-dia. vinyl-insulated round cable with
2 conductors (Conductor cross section:
0.5 mm2, Insulator diameter: 1.9 mm),
Standard length: 300 mm
29 dia.
24
E2EZ-X4C1
E2EZ-X4Y1
80
60
Indicator*2
*1
M18
× 1
4
4
Two clamping nuts
Two toothed washers
*1. C Models: 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross *2. C Models: Detection indicator (red),
section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m
Y Models: Operation indicator (red)
Y Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross
section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m
E2EZ-X8C1
E2EZ-X8Y1
42 dia.
36
80
60
Indicator*2
*1
M30 × 1.5
5
5
Two clamping nuts
Two toothed washers
*1. C Models: 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross *2. C Models: Detection indicator (red),
section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m
Y Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross
section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m
Y Models: Operation indicator (red)
Mounting Hole Dimensions
Model
F (mm)
+0.5
E2EZ-X2@
E2EZ-X4@
E2EZ-X8@
12.5 dia.
−0
+0.5
−0
18.5 dia.
+0.5
30.5 dia.
−0
F
8
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2014.1
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2014 All Right Reserved.
相关型号：
©2020 ICPDF网 联系我们和版权申明