E2EQ-X10D1-M1GJ-1 0.3M [OMRON]
SENS PROX M30 10MM DC2W-NO SHLD;
| 型号： | E2EQ-X10D1-M1GJ-1 0.3M |
| 厂家： | 
OMRON ELECTRONICS LLC |
| 描述： | SENS PROX M30 10MM DC2W-NO SHLD |
| 文件： | 总9页 (文件大小：822K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Spatter-resistant Proximity Sensor
E2EQ
CSM_E2EQ_DS_E_9_1
Spatter-resistant Fluororesin-
coated Proximity Sensor
• Superior spatter resistance.
• Long Sensing-distance Models added for sensing
distances up to 15 mm.
• Pre-wired Smartclick Connector Models are also
available.
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Be sure to read Safety Precautions on
page 6.
Ordering Information
Sensors [Refer to Dimensions on page 7.]
Pre-wired Models
Long Sensing-distance Models
Appearance
M12
Sensing distance
Output configuration
Operation mode
Model
E2EQ-X4X1 2M
4 mm
Shielded
DC 2-wire
(no polarity)
M18
M30
NO
E2EQ-X8X1 2M
E2EQ-X15X1 2M
8 mm
15 mm
Standard Models
Appearance
M12
Sensing distance
3 mm
Output configuration
Operation mode
Model
E2EQ-X3D1 2M
Shielded
M18
DC 2-wire
NO
E2EQ-X7D1 2M
E2EQ-X10D1 2M
7 mm
M30
10 mm
Pre-wired Smartclick Connector Models (M12)
Long Sensing-distance Models
Appearance
Sensing distance
Output configuration
Operation mode
Model
M12
E2EQ-X4X1-M1TJ 0.3M
4 mm
DC 2-wire
Shielded
(no polarity)
(3)-(4)
pin arrangement
M18
M30
NO
E2EQ-X8X1-M1TJ 0.3M
E2EQ-X15X1-M1TJ 0.3M
8 mm
15 mm
Standard Models
Standard Models
M12
Shielded
M18
Sensing distance
Output configuration
Operation mode
Model
E2EQ-X3D1-M1TGJ 0.3M
3 mm
DC 2-wire
(1)-(4)
pin arrangement
NO
E2EQ-X7D1-M1TGJ 0.3M
E2EQ-X10D1-M1TGJ 0.3M
7 mm
M30
10 mm
1
E2EQ
Pre-wired Connector Models (M12)
Long Sensing-distance Models
Appearance
M12
Sensing distance
Output configuration
Operation mode
Model
E2EQ-X4X1-M1J 0.3M
4 mm
DC 2-wire
(without polarity)
(3)-(4)
Shielded
M18
M30
NO
E2EQ-X8X1-M1J 0.3M
E2EQ-X15X1-M1J 0.3M
8 mm
pin arrangement
15 mm
Standard Models
Standard Models
M12
Sensing distance
Output configuration
Operation mode
Model
E2EQ-X3D1-M1GJ 0.3M
3 mm
DC 2-wire
(1)-(4)
pin arrangement
Shielded
M18
NO
E2EQ-X7D1-M1GJ 0.3M
E2EQ-X10D1-M1GJ 0.3M
7 mm
M30
10 mm
Accessories (Order Separately)
Sensor I/O Connectors (M12, Sockets on One Cable End)
(Models with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) [Refer to XS2, XS5.]
Appearance
Straight
Cable length
Sensor I/O Connector model number
XS2F-D421-DC0-F
Applicable Proximity Sensor model number
2 m
5 m
2 m
5 m
2 m
XS2F-D421-GC0-F
XS2F-D422-DC0-F
XS2F-D422-GC0-F
XS2F-D421-DA0-F
E2EQ-X@X1-M1J
L-shape
Straight
5 m
2 m
5 m
XS2F-D421-GA0-F
XS2F-D422-DA0-F
XS2F-D422-GA0-F
E2EQ-X@D1-M1GJ
L-shape
2 m
5 m
XS5F-D421-D80-F
XS5F-D421-G80-F
Smartclick
Connector
Straight
E2EQ-X@X1-M1TJ
E2EQ-X@D1-M1TGJ
Note: Refer to Introduction to Sensor I/O Connectors/Sensor Controllers for details.
Ratings and Specifications
Long Sensing-distance Models
Model
E2EQ-X4X1
E2EQ-X8X1
E2EQ-X15X1
E2EQ-X4X1-M1(T)J
E2EQ-X8X1-M1(T)J
E2EQ-X15X1-M1(T)J
Item
Sensing distance
Set distance *1
4 mm 10%
8 mm 10%
15 mm 10%
0 to 12 mm
0 to 3.2 mm
0 to 6.4 mm
Differential travel
Standard sensing object
Response frequency *2
15% max. of sensing distance
Iron, 12 × 12 × 1 mm
1 kHz
Iron, 18 × 18 × 1 mm
Iron, 30 × 30 × 1 mm
0.5 kHz
0.25 kHz
Load current
Control
3 to 100 mA
output
Residual voltage *3 5 V max. (Load current: 100 mA, Cable length: 2 m)
Operation mode (with sensing
object approaching)
Load ON: NO; For details, refer to the timing charts on page 5.
Protection circuits
Load short-circuit protection, Surge suppressor
Ambient temperature range
Operating: −25 to 70°C, Storage: −40 to 85°C, (with no icing or condensation)
15% max. of sensing distance at 23°C in the temperature range of −40 to 85°C
10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C
15% max. of sensing distance at 23°C in
the temperature range of −25 to 70°C
Temperature influence
Voltage influence
Shock resistance
Connection method
1% max. of sensing distance at rated voltage in the rated voltage 15% range
Destruction: 1,000m/s2 10 times each in X, Y, and Z directions
Pre-wired Models (Standard cable length: 2 m), Pre-wired Connector Models
Pre-wired Models
Weight
Approx. 65 g
Approx. 140 g
Approx. 190 g
Approx. 90 g
(packed
Pre-wired
Approx. 20 g
Approx. 40 g
state)
Connector Models
*1. Use the Sensor within the range in which the green indicator is ON.
*2. The response frequency is an average value.
*3. The residual voltage is 5 V. Make sure that the device connected to the Sensor can withstand the residual voltage.
2
E2EQ
Standard Models
Model
E2EQ-X3D1
E2EQ-X3D1-M1(T)GJ
E2EQ-X7D1
E2EQ-X7D1-M1(T)GJ
E2EQ-X10D1
E2EQ-X10D1-M1(T)GJ
Item
Sensing distance
Set distance
3 mm 10%
7 mm 10%
10 mm 10%
0 to 2.4 mm
0 to 5.6 mm
0 to 8 mm
Differential travel
Standard sensing object
Response frequency *
10% max. of sensing distance
Iron, 12 × 12 × 1 mm
1 kHz
Iron, 18 × 18 × 1 mm
Iron, 30 × 30 × 1 mm
500 Hz
400 Hz
Load current
3 to 100 mA
Control
output
Residual voltage
3 V max. (Load current: 100 mA, Cable length: 2 m)
Operation mode (with sensing
object approaching)
Load ON: NO; For details, refer to the timing charts on page 5.
Protection circuits
Load short-circuit protection, Surge suppressor
Ambient temperature range
Temperature influence
Voltage influence
Operating/Storage: −25 to 70°C (with no icing or condensation)
10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C
2.5% max. of sensing distance at rated voltage in the rated voltage 15% range
Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Shock resistance
E2EQ-X@D1: Pre-wired Models (Standard cable length: 2 m)
E2EQ-X@D1-M1GJ: Pre-wired Connector Models (Standard cable length: 300mm)
Connection method
Pre-wired Models Approx. 120 g
Approx. 160 g
Approx. 220 g
Weight
(packed
state)
Pre-wired
Approx. 80 g
Approx. 110 g
Approx. 190 g
Connector Models
* The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and
a set distance of half the sensing distance.
Common Ratings and Performance
Model
E2EQ-X4X1
E2EQ-X4X1-M1(T)J
E2EQ-X3D1
E2EQ-X8X1
E2EQ-X8X1-M1(T)J
E2EQ-X7D1
E2EQ-X15X1
E2EQ-X15X1-M1(T)J
E2EQ-X10D1
Item
E2EQ-X3D1-M1(T)GJ
E2EQ-X7D1-M1(T)GJ
E2EQ-X10D1-M1(T)GJ
Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page
4.)
Detectable object
Power supply voltage
(operating voltage range)
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
Leakage current
Indicators
0.8 mA max.
Operation indicator (red), Setting indicator (green)
Operating/Storage: 35% to 95% (with no condensation)
50 MΩ min. (at 500 VDC) between current-carrying parts and case
1,000 VAC for 1 min between current-carrying parts and case
Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
IEC 60529 IP67, in-house standards: oil-resistant
Fluororesin coating (Base material: brass)
Fluororesin
Ambient humidity range
Insulation resistance
Dielectric strength
Vibration resistance
Degree of protection
Case
Sensing surface
Clamping nuts
Toothed washer
Materials
Fluororesin coating (Base material: brass)
Zinc-plated iron
Accessories
Instruction manual
3
E2EQ
Engineering Data (Reference Value)
Sensing Area
E2EQ-X@X@(-M1(T)J) Shielded Models E2EQ-X@D@(-M1(T)GJ)
18
16
E2EQ-X15X
10
14
E2EQ-X10D1
E2EQ-X7D1
8
12
10
8
E2EQ-X8X
E2EQ-X4X
6
4
2
E2EQ-X3D1
6
Y
Y
X
X
4
2
0
−20 −16 −12 −8 −4
0
4
8
12 16 20
−20 −15 −10
−5
0
5
10
15 20
Distance Y
(mm)
Distance Y (mm)
E2EQ-X3D1 Sensing Head
E2EQ-X7D1 Sensing Head
E2EQ-X10D1 Sensing Head
Influence of Sensing Object Size and Material
E2EQ-X4X1(-M1(T)J)
E2EQ-X8X1(-M1(T)J)
E2EQ-X15X1(-M1(T)J)
5
10
20
d ×
d ×
d ×
d
d
d
t = 1 mm
t = 1 mm
X
t = 1 mm
X
X
4
3
2
1
Iron
8
Iron
16
12
8
Iron
Stainless steel
(SUS304)
6
4
2
Stainless steel
(SUS304)
Stainless steel
(SUS304)
Brass
Brass
Copper
Brass
Aluminum
Copper
4
Copper
0
5
10
15
20
25
30
35
0
10
20
30
40
50
0
10
20
30
40
50
60
70 80
Side length of sensing object: d (mm)
Side length of sensing object: d (mm)
Side length of sensing object: d (mm)
E2EQ-X3D1(-M1(T)GJ)
E2EQ-X7D1(-M1(T)GJ)
E2EQ-X10D1(-M1(T)GJ)
4.0
10
14
d ×
d ×
d ×
d
9
8
7
6
5
4
3
2
1
d
d
t = 1 mm
t
= 1 mm
3.5
3.0
2.5
2.0
1.5
1.0
0.5
t = 1 mm
12
10
8
X
X
X
Iron
Stainless steel
(SUS304)
Iron
Iron
Stainless steel
(SUS304)
Aluminum
Brass
Stainless steel
(SUS304)
6
Brass
Brass
4
Aluminum
Copper
Copper
Copper
Aluminum
2
0
5
10
15
20
25
30
35
0
5
10
15
20
25
30
35
40
45
0
5
10 15 20 25 30 35 40 45 50 55
Side length of sensing object: d (mm)
Side length of sensing object: d (mm)
Side length of sensing object: d (mm)
4
E2EQ
Residual Output Voltage
Leakage Current
E2EQ-X@D
1.5
E2EQ-X@X@(-M1(T)J)
E2EQ-X@D@(-M1(T)GJ)
5
5
4
3
2
4
3
2
1
0
1.0
0.5
E2EQ-X3D1
1
0
E2EQ-X10D1
30
E2EQ-X7D1
20
1
3
5
10
30
50 100
1
3
5
10
30 50 100
300 500 1,000
0
10
40
Load current (mA)
Load current (mA)
Power supply voltage (V)
I/O Circuit Diagrams
Long Sensing-distance Models
Operation
Model
mode
Timing Chart
Output circuit
Brown
Load
4
3
+V
Set position
Unstable
sensing
area
Proximity
Sensor
main
Non-sensing area
Stable sensing area
circuit
Blue
0 V
Sensing
object
E2EQ-X4X1
E2EQ-X8X1
Note 1. The load can be connected to either the +V or
0 V side.
Note 2. There is no polarity. Therefore, the brown and
blue lines have no polarity.
E2EQ-X15X1
E2EQ-X4X1-M1(T)J
E2EQ-X8X1-M1(T)J
E2EQ-X15X1-M1(T)J
100 80 (TYP)
Rated
sensing
distance
0
(%)
NO
ON
Setting indicator
(green)
OFF
Connector Pin Arrangement
ON Operation indicator
(red)
OFF
1
ON
Control output
2
4
OFF
3
Note: Pins 1 and 2 are not used.
Standard Models
Operation
Model
mode
Timing Chart
Output circuit
Brown
Set position
Unstable
sensing
area
Load
+V
1
Non-sensing area
Stable sensing area
Proximity
Sensor
main
Proximity Sensor
Sensing
object
circuit
Blue
E2EQ-X3D1
E2EQ-X7D1
E2EQ-X10D1
E2EQ-X3D1-M1(T)GJ
E2EQ-X7D1-M1(T)GJ
E2EQ-X10D1-M1(T)GJ
0 V
4
(%)
100 80 (TYP)
0
Note: The load can be connected to either the +V
or 0 V side.
NO
Rated
sensing
distance
ON
Setting indicator
(green)
OFF
ON
Connector Pin Arrangement
Operation
indicator (red)
1
OFF
ON
2
4
3
Control output
OFF
Note: Pins 2 and 3 are not used.
5
E2EQ
Pre-wired Connector Model Connections
Model
E2EQ-X@X1-M1(T)J
E2EQ-X@D1-M1(T)GJ
Pre-wired Connector
Model
E2EQ-X@D1-M1GJ
Pre-wired Connector Sensor I/O Connector
Sensor I/O Connector
XS2F-D42@-@A0-F
Model
XS2F-D42@-@C0-F
E2EQ-X@X1-M1J
1
2
3
4
1
2
3
4
Brown
1
2
3
4
1
2
3
4
Brown (+)
(not used)
Blue (−)
Black (+)
Blue (−)
Connections
Pre-wired Connector
Model
E2EQ-X@D1-M1TGJ
Pre-wired Connector Sensor I/O Connector
Sensor I/O Connector
XS5F-D421-@80-F
Model
XS5F-D421-@80-F
E2EQ-X@X1-M1TJ
1
2
3
4
1
2
3
4
Brown (not used)
White (not used)
Blue (−)
1
2
3
4
1
2
3
4
Brown (+)
White (not used)
Blue (not used)
Black (−)
Black (+)
Safety Precautions
Refer to Warranty and Limitations of Liability.
Mutual Interference
WARNING
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
When installing two or more Sensors face-to-face or side-by-side,
ensure that the minimum distances given in the following table are
maintained.
B
A
Precautions for Correct Use
Do not use this product under ambient conditions that exceed the
ratings.
Mutual Interference (Unit: mm)
Model
Item
A
30
B
E2EQ-X4X1(-M1(T)J)
E2EQ-X8X1(-M1(T)J)
E2EQ-X15X1(-M1(T)J)
E2EQ-X3D1(-M1(T)GJ)
E2EQ-X7D1(-M1(T)GJ)
E2EQ-X10D1(-M1(T)GJ)
20
35
90
20
35
70
● Design
60
Influence of Surrounding Metal
110
30
When mounting the Sensor within a metal panel, ensure that the
clearances given in the following table are maintained. Failure to
maintain these distances may cause deterioration in the performance
of the Sensor.
50
100
● Mounting
l
Do not tighten the nut with excessive force. A washer must be used
with the nut.
n
d dia.
m
Shielded Model
D
m
l
Influence of Surrounding Metal (Unit: mm)
Model
Item
l
d
D
2.4
3.6
6
m
12
24
45
8
n
Part B Part A
E2EQ-X4X1(-M1(T)J)
E2EQ-X8X1(-M1(T)J)
E2EQ-X15X1(-M1(T)J)
E2EQ-X3D1(-M1(T)GJ)
E2EQ-X7D1(-M1(T)GJ)
E2EQ-X10D1(-M1(T)GJ)
2.4
3.6
6
18
27
45
12
18
30
18
27
45
18
27
45
Note: 1. The allowable tightening strength depends on the distance from the
edge of the head, as shown in the following table. (A is the distance
from the edge of the head. B includes the nut on the head side. If the
edge of the nut is in part A, the tightening torque for part A applies
instead.)
0
0
20
40
2. The following torque assume washers are being used.
Torque
Part A
Part B
Dimension
(mm)
Model
Torque
Torque
E2EQ-X4X1(-M1(T)J)
E2EQ-X8X1(-M1(T)J)
E2EQ-X15X1(-M1(T)J)
E2EQ-X3D1(-M1(T)GJ)
E2EQ-X7D1(-M1(T)GJ)
E2EQ-X10D1(-M1(T)GJ)
30 N·m
70 N·m
180 N·m
---
24
29
26
15 N·m
39 N·m
---
78 N·m
6
E2EQ
(Unit: mm)
Dimensions
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
Pre-wired Models
Long Sensing-distance Models
E2EQ-X4X1
38
33
9
21 dia.
17
4
10
2
*1
Indicators *2
Two clamping nuts
M12 × 1
Toothed washer
*1. 4-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant,
Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm),
Standard length: 2 m
The cable can be extended up to 200 m (separate metal conduit).
*2. Operation indicator (red), Setting indicator (green)
E2EQ-X8X1
E2EQ-X15X1
48
43
12
42 dia.
36
43
38
12
5
10
3
29 dia.
24
4
10
2
*1
*1
Indicators *2
Indicators *2
M18 × 1
Two clamping nuts
Toothed washer
M30 × 1.5
Two clamping nuts
Toothed washer
*1. 6-dia. vinyl-insulated round cable with 2 conductors
(Flame-resistant, Conductor cross section: 0.5 mm2,
Insulator diameter: 1.9 mm), Standard length: 2 m
The cable can be extended up to 200 m (separate
metal conduit).
*1. 6-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant,
Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm),
Standard length: 2 m
The cable can be extended up to 200 m (separate metal conduit).
*2. Operation indicator (red), Setting indicator (green)
*2. Operation indicator (red), Setting indicator (green)
Standard Models
E2EQ-X3D1
38
27.6
24
21 dia.
17
5
*1
Indicators *2
M12 × 1
4
Two clamping nuts (fluororesin coated)
Two toothed washers
*1. 6-dia. vinyl-insulated round cable with 2 conductors
(Flame-resistant, Conductor cross section: 0.5 mm2,
Insulator diameter: 1.9 mm), Standard length: 2 m
The cable can be extended up to 200 m (separate metal
conduit).
*2. Operation indicator (red), Setting indicator (green)
E2EQ-X7D1
E2EQ-X10D1
47
32
56
42
29 dia.
24
42 dia.
36
29
6
38
10
*1
Indicators *2
*1
M18 × 1
Two clamping nuts (fluororesin coated)
Two toothed washers
4
Indicators *2
Two clamping nuts (fluororesin coated)
Two toothed washers
*1. 6-dia. vinyl-insulated round cable with 2 conductors
(Flame-resistant, Conductor cross section: 0.5 mm2,
Insulator diameter: 1.9 mm), Standard length: 2 m
The cable can be extended up to 200 m (separate metal
conduit).
5
M30 × 1.5
*1. 6-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant,
Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm),
Standard length: 2 m
*2. Operation indicator (red), Setting indicator (green)
The cable can be extended up to 200 m (separate metal conduit).
*2. Operation indicator (red), Setting indicator (green)
7
E2EQ
Pre-wired Connector Models
Long Sensing-distance Models
E2EQ-X4X1-M1(T)J
38
33
9
21 dia.
17
10
4
2
1*
Indicators *2
M12 × 1
M12 × 1
Toothed Two clamping nuts
washer
*1. 4-dia. vinyl-insulated round cable (Flame-resistant,
Conductor cross section: 0.3 mm2, Insulator diameter:
1.3 mm), Standard length: 300 mm
*2. Operation indicator (red), Setting indicator (green)
E2EQ-X8X1-M1(T)J
E2EQ-X15X1-M1(T)J
48
43
12
42 dia.
36
43
38
12
5
10
29 dia.
24
3
4
10
2
1*
*1
M12 × 1
Indicators *2
Indicators *2
M12 × 1
M18 × 1
M30 × 1.5
Two clamping nuts
Toothed
washer
Toothed
washer
Two clamping nuts
*1. 6-dia. vinyl-insulated round cable (Flame-resistant,
Conductor cross section: 0.5 mm2, Insulator diameter:
1.9 mm), Standard length: 300 mm
*1. 6-dia. vinyl-insulated round cable (Flame-resistant,
Conductor cross section: 0.5 mm2, Insulator
diameter: 1.9 mm), Standard length: 300 mm
*2. Operation indicator (red), Setting indicator (green)
*2. Operation indicator (red), Setting indicator (green)
Standard Models
E2EQ-X3D1-M1(T)GJ
38
27.6
24
*1. 6-dia. vinyl-insulated round cable (flame-resistant),
Standard length: 300 mm
*2. Operation indicator (red), Setting indicator (green)
21 dia.
17
5
Indicators *2
*1
M12 × 1
(aluminum)
M12
1
4
×
Two clamping nuts (fluororesin coated)
Two toothed washers
E2EQ-X7D1-M1(T)GJ
E2EQ-X10D1-M1(T)GJ
*1. 6-dia. vinyl-insulated round cable
(flame-resistant), Standard
length: 300 mm
*2. Operation indicator (red), Setting
indicator (green)
56
*1. 6-dia. vinyl-insulated round cable (flame-
resistant), Standard length: 300 mm
*2. Operation indicator (red), Setting
indicator (green)
42 dia.
36
42
38
47
29 dia.
24
32
29
10
6
M12 × 1 (aluminum)
M12 × 1 (aluminum)
*1
*1
*2
Indicators
*2
Indicators
Two clamping nuts (fluororesin coated)
Two toothed washers
M18 × 1
4
Two clamping nuts (fluororesin coated)
Two toothed washers
M30 × 1.5
5
Mounting Hole Dimensions
E2EQ-X4X@
E2EQ-X3@
E2EQ-X8X@
E2EQ-X7@
E2EQ-X15X@
E2EQ-X10@
Model
F (mm)
12.5+00.5 dia.
18.5+00.5 dia.
30.5+00.5 dia.
F
8
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2015.1
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2015 All Right Reserved.
相关型号：
©2020 ICPDF网 联系我们和版权申明