P89C51RD2HBA_技术文档

INTEGRATED CIRCUITS

89C51RB2/89C51RC2/89C51RD2

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

Preliminary specification

IC28 Data Handbook

1999 Sep 23

Philips

Semiconductors

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

DESCRIPTION

FEATURES

The 89C51RB2/RC2/RD2 device contains a non-volatile

16kB/32kB/64kB Flash program memory that is both parallel

programmable and serial In-System and In-Application

Programmable. In-System Programming (ISP) allows the user to

download new code while the microcontroller sits in the application.

In-Application Programming (IAP) means that the microcontroller

fetches new program code and reprograms itself while in the

system. This allows for remote programming over a modem link.

A default serial loader (boot loader) program in ROM allows serial

In-System programming of the Flash memory via the UART without

the need for a loader in the Flash code. For In-Application

Programming, the user program erases and reprograms the Flash

memory by use of standard routines contained in ROM.

• 80C51 Central Processing Unit

• On-chip Flash Program Memory with In-System Programming

(ISP) and In-Application Programming (IAP) capability

• Boot ROM contains low level Flash programming routines for

downloading via the UART

• Can be programmed by the end-user application (IAP)

• 6 clocks per machine cycle operation (standard)

• 12 clocks per machine cycle operation (optional)

• Speed up to 20 MHz with 6 clock cycles per machine cycle

(40 MHz equivalent performance); up to 33 MHz with 12 clocks

per machine cycle

This device executes one machine cycle in 6 clock cycles, hence

providing twice the speed of a conventional 80C51. An OTP

configuration bit lets the user select conventional 12 clock timing

if desired.

• Fully static operation

• RAM expandable externally to 64 kB

• 4 level priority interrupt

• 8 interrupt sources

This device is a Single-Chip 8-Bit Microcontroller manufactured in

advanced CMOS process and is a derivative of the 80C51

microcontroller family. The instruction set is 100% compatible with

the 80C51 instruction set.

• Four 8-bit I/O ports

The device also has four 8-bit I/O ports, three 16-bit timer/event

counters, a multi-source, four-priority-level, nested interrupt structure,

an enhanced UART and on-chip oscillator and timing circuits.

• Full-duplex enhanced UART

– Framing error detection

– Automatic address recognition

The added features of the P89C51RB2/RC2/RD2 makes it a

powerful microcontroller for applications that require pulse width

modulation, high-speed I/O and up/down counting capabilities such

as motor control.

• Power control modes

– Clock can be stopped and resumed

– Idle mode

– Power down mode

• Programmable clock out

• Second DPTR register

• Asynchronous port reset

• Low EMI (inhibit ALE)

• Programmable Counter Array (PCA)

– PWM

– Capture/compare

2

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

ORDERING INFORMATION

PHILIPS

(EXCEPT NORTH

AMERICA)

PART ORDER

NUMBER

PART MARKING

PHILIPS

NORTH

AMERICA

PART ORDER

NUMBER

MEMORY

FREQUENCY (MHz)

TEMPERATURE

RANGE (°C)

AND PACKAGE

VOLTAGE

RANGE

DWG #

FLASH RAM

6 CLOCK

MODE

12 CLOCK

MODE

1

2

P89C51RB2HBP

P89C51RB2HFP

P89C51RB2HBA

P89C51RB2HFA

P89C51RB2HBB

P89C51RB2HFB

P89C51RC2HBP

P89C51RC2HFP

P89C51RC2HBA

P89C51RC2HFA

P89C51RC2HBB

P89C51RC2HFB

P89C51RD2HBP

P89C51RD2HFP

P89C51RD2HBA

P89C51RD2HFA

P89C51RD2HBB

P89C51RD2HFB

P89C51RB2BP

P89C51RB2FP

P89C51RB2BA

P89C51RB2FA

P89C51RB2BB

P89C51RB2FB

P89C51RC2BP

P89C51RC2FP

P89C51RC2BA

P89C51RC2FA

P89C51RC2BB

P89C51RC2FB

P89C51RD2BP

P89C51RD2FP

P89C51RD2BA

P89C51RD2FA

P89C51RD2BB

P89C51RD2FB

16 kB 512 B

0 to +70, PDIP

–40 to +85, PDIP

0 to +70, PLCC

4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT129-1

4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT187-2

4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT307-2

4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT129-1

4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT187-2

4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT307-2

4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT129-1

4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT187-2

4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT307-2

3

4

16 kB 512 B –40 to +85, PLCC

16 kB 512 B 0 to +70, PQFP

16 kB 512 B –40 to +85, PQFP

5

6

7

32 kB 512 B

0 to +70, PDIP

–40 to +85, PDIP

0 to +70, PLCC

8

9

10

11

12

13

14

15

16

17

32 kB 512 B –40 to +85, PLCC

32 kB 512 B 0 to +70, PQFP

32 kB 512 B –40 to +85, PQFP

64 kB

1 kB

0 to +70, PDIP

–40 to +85, PDIP

0 to +70, PLCC

–40 to +85, PLCC

0 to +70, PQFP

–40 to +85, PQFP

18

3

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

BLOCK DIAGRAM

P0.0–P0.7

P2.0–P2.7

PORT 0

DRIVERS

PORT 2

DRIVERS

V

CC

SS

RAM ADDR

REGISTER

PORT 0

LATCH

PORT 2

LATCH

FLASH

RAM

8

B

STACK

POINTER

ACC

REGISTER

PROGRAM

ADDRESS

REGISTER

TMP1

TMP2

BUFFER

ALU

SFRs

TIMERS

P.C.A.

PC

INCRE-

MENTER

PSW

8

16

PROGRAM

COUNTER

PSEN

ALE

DPTR’S

MULTIPLE

TIMING

AND

CONTROL

EAV

PP

RST

PORT 1

LATCH

PORT 3

LATCH

PD

OSCILLATOR

PORT 1

DRIVERS

PORT 3

DRIVERS

XTAL1

XTAL2

P1.0–P1.7

P3.0–P3.7

SU01065

4

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

LOGIC SYMBOL

Plastic Leaded Chip Carrier

6

1

40

V

SS

CC

XTAL1

7

39

ADDRESS AND

DATA BUS

LCC

XTAL2

RST

17

29

T2

T2EX

18

28

EA/V

PP

Pin Function

PSEN

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

NIC*

P1.0/T2

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

P3.4/T0

P3.5/T1

P3.6/WR

P3.7/RD

XTAL2

XTAL1

V

SS

NIC*

P2.0/A8

P2.1/A9

P2.2/A10

P2.3/A11

P2.4/A12

P2.5/A13

P2.6/A14

31

32

33

34

35

36

37

38

39

40

41

42

43

44

P2.7/A15

PSEN

ALE/PROG

NIC*

ALE/PROG

RxD

P1.1/T2EX

P1.2/ECI

P1.3/CEX0

P1.4/CEX1

P1.5/CEX2

P1.6/CEX3

P1.7/CEX4

RST

P3.0/RxD

NIC*

P3.1/TxD

P3.2/INT0

P3.3/INT1

TxD

INT0

EA/V

PP

INT1

T0

T1

WR

RD

P0.7/AD7

P0.6/AD6

P0.5/AD5

P0.4/AD4

P0.3/AD3

P0.2/AD2

P0.1/AD1

P0.0/AD0

ADDRESS BUS

SU01302

V

CC

* NO INTERNAL CONNECTION

PINNING

Plastic Dual In-Line Package

SU00023

Plastic Quad Flat Pack

T2/P1.0

40

39

V

CC

1

2

3

44

34

T2EX/P1.1

P0.0/AD0

ECI/P1.2

38 P0.1/AD1

37 P0.2/AD2

1

33

23

CEX0/P1.3

CEX1/P1.4

4

5

36

P0.3/AD3

35 P0.4/AD4

34

PQFP

CEX2/P1.5

CEX3/P1.6

CEX4/P1.7

RST

6

7

8

9

11

P0.5/AD5

33 P0.6/AD6

32

12

Pin Function

22

P0.7/AD7

Pin Function

DUAL

IN-LINE

PACKAGE

31 EA/V

RxD/P3.0 10

TxD/P3.1 11

INT0/P3.2 12

PP

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

P1.5/CEX2

P1.6/CEX3

P1.7/CEX4

RST

P3.0/RxD

NIC*

P3.1/TxD

P3.2/INT0

P3.3/INT1

P3.4/T0

P3.5/T1

P3.6/WR

P3.7/RD

XTAL2

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

V

31

32

33

34

35

36

37

38

39

40

41

42

43

44

P0.6/AD6

P0.5/AD5

P0.4/AD4

P0.3/AD3

P0.2/AD2

P0.1/AD1

P0.0/AD0

SS

30

NIC*

ALE/PROG

P2.0/A8

P2.1/A9

P2.2/A10

P2.3/A11

P2.4/A12

P2.5/A13

P2.6/A14

P2.7/A15

PSEN

29 PSEN

28

13

INT1/P3.3

P2.7/A15

27 P2.6/A14

26

T0/P3.4 14

T1/P3.5 15

WR/P3.6 16

RD/P3.7 17

XTAL2 18

XTAL1 19

V

CC

P2.5/A13

NIC*

P1.0/T2

P1.1/T2EX

P1.2/ECI

P1.3/CEX0

P1.4/CEX1

25 P2.4/A12

24 P2.3/A11

ALE/PROG

NIC*

EA/V

PP

23

22

P2.2/A10

P2.1/A9

P2.0/A8

XTAL1

P0.7/AD7

SU00024

* NO INTERNAL CONNECTION

21

V

20

SS

SU00021

5

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

PIN DESCRIPTIONS

PIN NUMBER

MNEMONIC

TYPE

NAME AND FUNCTION

PDIP

20

PLCC

22

PQFP

16

V

SS

I

Ground: 0 V reference.

V

CC

40

44

38

Power Supply: This is the power supply voltage for normal, idle, and power-down

operation.

P0.0–0.7

39–32

1–8

43–36

2–9

37–30

I/O

Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s

written to them float and can be used as high-impedance inputs. Port 0 is also the

multiplexed low-order address and data bus during accesses to external program

and data memory. In this application, it uses strong internal pull-ups when emitting 1s.

P1.0–P1.7

40–44,

1–3

I/O

Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups on all pins

except P1.6 and P1.7 which are open drain. Port 1 pins that have 1s written to them

are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1

pins that are externally pulled low will source current because of the internal

pull-ups. (See DC Electrical Characteristics: I ).

IL

Alternate functions for 89C51RB2/RC2/RD2 Port 1 include:

1

2

40

I/O

T2 (P1.0): Timer/Counter 2 external count input/Clockout (see Programmable

Clock-Out)

2

3

4

5

6

7

8

3

4

5

6

7

8

9

41

42

43

44

1

I

T2EX (P1.1): Timer/Counter 2 Reload/Capture/Direction Control

ECI (P1.2): External Clock Input to the PCA

I

I/O

CEX0 (P1.3): Capture/Compare External I/O for PCA module 0

CEX1 (P1.4): Capture/Compare External I/O for PCA module 1

CEX2 (P1.5): Capture/Compare External I/O for PCA module 2

CEX3 (P1.6): Capture/Compare External I/O for PCA module 3

CEX4 (P1.7): Capture/Compare External I/O for PCA module 4

2

3

P2.0–P2.7

21–28

24–31

18–25

I/O

Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that

have 1s written to them are pulled high by the internal pull-ups and can be used as

inputs. As inputs, port 2 pins that are externally being pulled low will source current

because of the internal pull-ups. (See DC Electrical Characteristics: I ). Port 2

IL

emits the high-order address byte during fetches from external program memory

and during accesses to external data memory that use 16-bit addresses (MOVX

@DPTR). In this application, it uses strong internal pull-ups when emitting 1s.

During accesses to external data memory that use 8-bit addresses (MOV @Ri),

port 2 emits the contents of the P2 special function register.

P3.0–P3.7

10–17

11,

13–19

5, 7–13

I/O

Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that

have 1s written to them are pulled high by the internal pull-ups and can be used as

inputs. As inputs, port 3 pins that are externally being pulled low will source current

because of the pull-ups. (See DC Electrical Characteristics: I ). Port 3 also serves

IL

the special features of the 89C51RB2/RC2/RD2, as listed below:

10

11

12

13

14

15

16

17

11

13

14

15

16

17

18

19

5

7

I

O

I

RxD (P3.0): Serial input port

TxD (P3.1): Serial output port

8

INT0 (P3.2): External interrupt

9

I

INT1 (P3.3): External interrupt

10

11

12

13

I

T0 (P3.4): Timer 0 external input

I

T1 (P3.5): Timer 1 external input

O

WR (P3.6): External data memory write strobe

RD (P3.7): External data memory read strobe

RST

ALE

9

10

4

I

Reset: A high on this pin for two machine cycles while the oscillator is running,

resets the device. An internal diffused resistor to V permits a power-on reset

SS

using only an external capacitor to V

.

CC

30

33

27

O

Address Latch Enable: Output pulse for latching the low byte of the address

during an access to external memory. In normal operation, ALE is emitted twice

every machine cycle, and can be used for external timing or clocking. Note that one

ALE pulse is skipped during each access to external data memory. ALE can be

disabled by setting SFR auxiliary.0. With this bit set, ALE will be active only during a

MOVX instruction.

6

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

PIN NUMBER

MNEMONIC

TYPE

NAME AND FUNCTION

PDIP

PLCC

PQFP

PSEN

29

32

26

O

Program Store Enable: The read strobe to external program memory. When

executing code from the external program memory, PSEN is activated twice each

machine cycle, except that two PSEN activations are skipped during each access

to external data memory. PSEN is not activated during fetches from internal

program memory.

EA/V

31

35

29

I

External Access Enable/Programming Supply Voltage: EA must be externally

held low to enable the device to fetch code from external program memory

locations. If EA is held high, the device executes from internal program memory.

The value on the EA pin is latched when RST is released and any subsequent

changes have no effect. This pin also receives the programming supply voltage

PP

(V ) during Flash programming.

PP

XTAL1

19

18

21

20

15

14

I

Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock

generator circuits.

XTAL2

O

Crystal 2: Output from the inverting oscillator amplifier.

NOTE:

To avoid “latch-up” effect at power-on, the voltage on any pin (other than V ) must not be higher than V + 0.5 V or less than V – 0.5 V.

PP

CC

SS

7

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

Table 1. Special Function Registers

DIRECT

ADDRESS

BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION

RESET

VALUE

SYMBOL

DESCRIPTION

MSB

E7

–

LSB

E0

ACC*

AUXR#

AUXR1#

B*

Accumulator

E0H

8EH

A2H

F0H

E6

–

E5

E4

–

E3

–

E2

–

E1

00H

EXTRAM

Auxiliary

–

AO

xxxxxx10B

xxxxxxx0B

00H

ENBOOT

Auxiliary 1

B register

–

GF2

F3

0

–

DPS

F0

F7

F6

F5

F4

F2

F1

CCAP0H# Module 0 Capture High

CCAP1H# Module 1 Capture High

CCAP2H# Module 2 Capture High

CCAP3H# Module 3 Capture High

CCAP4H# Module 4 Capture High

CCAP0L# Module 0 Capture Low

CCAP1L# Module 1 Capture Low

CCAP2L# Module 2 Capture Low

CCAP3L# Module 3 Capture Low

CCAP4L# Module 4 Capture Low

FAH

FBH

FCH

FDH

FEH

EAH

EBH

ECH

EDH

EEH

xxxxxxxxB

CCAPM0# Module 0 Mode

CCAPM1# Module 1 Mode

CCAPM2# Module 2 Mode

CCAPM3# Module 3 Mode

CCAPM4# Module 4 Mode

DAH

DBH

DCH

DDH

DEH

–

ECOM CAPP

CAPN

MAT

TOG

PWM

ECCF

x0000000B

DF

CF

DE

CR

DD

–

DC

DB

DA

D9

D8

CCON*#

CH#

CL#

PCA Counter Control

PCA Counter High

PCA Counter Low

D8H

F9H

E9H

CCF4

CCF3

CCF2

CCF1

CCF0

00x00000B

00H

CMOD#

PCA Counter Mode

D9H

CIDL

WDTE

–

CPS1

CPS0

ECF

00xxx000B

DPTR:

DPH

DPL

Data Pointer (2 bytes)

Data Pointer High

Data Pointer Low

83H

82H

00H

AF

EA

BF

–

AE

EC

AD

ET2

BD

AC

ES

AB

ET1

BB

AA

EX1

BA

A9

ET0

B9

A8

EX0

B8

IE*

Interrupt Enable 0

Interrupt Priority

A8H

B8H

B7H

00H

BE

BC

PS

IP*

PPC

B6

PT2

B5

PT1

B3

PX1

B2

PT0

B1

PX0

B0

x0000000B

B7

–

B4

IPH#

Interrupt Priority High

PPCH

PT2H

PSH

PT1H

PX1H

PT0H

PX0H

87

AD7

97

86

AD6

96

85

AD5

95

84

AD4

94

83

AD3

93

82

AD2

92

81

AD1

91

80

AD0

90

P0*

P1*

P2*

P3*

Port 0

Port 1

Port 2

80H

90H

A0H

FFH

CEX4

A7

CEX3

A6

CEX2

A5

CEX1

A4

CEX0

A3

ECI

A2

T2EX

A1

T2

A0

AD15

B7

AD14

B6

AD13

B5

AD12

B4

AD11

B3

AD10

B2

AD9

B1

AD8

B0

Port 3

B0H

87H

RD

WR

T1

T0

INT1

INT0

TxD

RxD

FFH

1

PCON#

Power Control

SMOD1 SMOD0

–

GF1

GF0

PD

IDL

00xxx000B

*

SFRs are bit addressable.

#

–

SFRs are modified from or added to the 80C51 SFRs.

Reserved bits.

1. Reset value depends on reset source.

8

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

Table 1. Special Function Registers (Continued)

BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION

DIRECT

ADDRESS

RESET

VALUE

SYMBOL

DESCRIPTION

MSB

LSB

D7

CY

D6

AC

D5

F0

D4

D3

D2

D1

F1

D0

P

PSW*

Program Status Word

D0H

RS1

RS0

OV

00000000B

RCAP2H#

RCAP2L#

Timer 2 Capture High

Timer 2 Capture Low

CBH

CAH

00H

SADDR# Slave Address

SADEN# Slave Address Mask

A9H

B9H

00H

SBUF

Serial Data Buffer

99H

xxxxxxxxB

9F

9E

9D

9C

9B

9A

99

TI

98

RI

SM0/FE

SCON*

SP

Serial Control

Stack Pointer

98H

81H

SM1

SM2

REN

TB8

RB8

00H

07H

8F

8E

8D

8C

8B

8A

89

88

TCON*

Timer Control

88H

TF1

TR1

TF0

TR0

IE1

IT1

IE0

IT0

00H

CF

TF2

–

CE

EXF2

–

CD

RCLK

–

CC

TCLK

–

CB

EXEN2

–

CA

TR2

–

C9

C8

T2CON*

Timer 2 Control

C8H

C9H

C/T2

T2OE

CP/RL2 00H

DCEN xxxxxx00B

T2MOD# Timer 2 Mode Control

TH0

TH1

TH2#

TL0

TL1

TL2#

Timer High 0

Timer High 1

Timer High 2

Timer Low 0

Timer Low 1

Timer Low 2

8CH

8DH

CDH

8AH

8BH

CCH

00H

TMOD

Timer Mode

89H

A6H

GATE

C/T

M1

M0

GATE

C/T

M1

M0

00H

WDTRST Watchdog Timer Reset

*

SFRs are bit addressable.

#

–

SFRs are modified from or added to the 80C51 SFRs.

Reserved bits.

OSCILLATOR CHARACTERISTICS

RESET

XTAL1 and XTAL2 are the input and output, respectively, of an

inverting amplifier. The pins can be configured for use as an

on-chip oscillator.

A reset is accomplished by holding the RST pin high for at least two

machine cycles (12 oscillator periods in 6 clock mode, or 24 oscillator

periods in 12 clock mode), while the oscillator is running. To ensure a

good power-on reset, the RST pin must be high long enough to allow

the oscillator time to start up (normally a few milliseconds) plus two

To drive the device from an external clock source, XTAL1 should be

driven while XTAL2 is left unconnected. Minimum and maximum

high and low times specified in the data sheet must be observed.

machine cycles. At power-on, the voltage on V and RST must

CC

come up at the same time for a proper start-up. Ports 1, 2, and 3 will

asynchronously be driven to their reset condition when a voltage

This device is configured at the factory to operate using 6 clock

periods per machine cycle, referred to in this datasheet as “6 clock

mode”. (This yields performance equivalent to twice that of standard

80C51 family devices). It may be optionally configured on

commercially-available EPROM programming equipment to operate

at 12 clocks per machine cycle, referred to in this datasheet as

“12 clock mode”. Once 12 clock mode has been configured, it

cannot be changed back to 6 clock mode.

above V

(min.) is applied to RESET.

IH1

The value on the EA pin is latched when RST is deasserted and has

no further effect.

9

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

LOW POWER MODES

Stop Clock Mode

Design Consideration

The static design enables the clock speed to be reduced down to

0 MHz (stopped). When the oscillator is stopped, the RAM and

Special Function Registers retain their values. This mode allows

step-by-step utilization and permits reduced system power

consumption by lowering the clock frequency down to any value. For

lowest power consumption the Power Down mode is suggested.

• When the idle mode is terminated by a hardware reset, the device

normally resumes program execution, from where it left off, up to

two machine cycles before the internal reset algorithm takes

control. On-chip hardware inhibits access to internal RAM in this

event, but access to the port pins is not inhibited. To eliminate the

possibility of an unexpected write when Idle is terminated by reset,

the instruction following the one that invokes Idle should not be

one that writes to a port pin or to external memory.

Idle Mode

In the idle mode (see Table 2), the CPU puts itself to sleep while all

of the on-chip peripherals stay active. The instruction to invoke the

idle mode is the last instruction executed in the normal operating

mode before the idle mode is activated. The CPU contents, the

on-chip RAM, and all of the special function registers remain intact

during this mode. The idle mode can be terminated either by any

enabled interrupt (at which time the process is picked up at the

interrupt service routine and continued), or by a hardware reset

which starts the processor in the same manner as a power-on reset.

ONCE Mode

The ONCE (“On-Circuit Emulation”) Mode facilitates testing and

debugging of systems without the device having to be removed from

the circuit. The ONCE Mode is invoked by:

1. Pull ALE low while the device is in reset and PSEN is high;

2. Hold ALE low as RST is deactivated.

While the device is in ONCE Mode, the Port 0 pins go into a float

state, and the other port pins and ALE and PSEN are weakly pulled

high. The oscillator circuit remains active. While the device is in this

mode, an emulator or test CPU can be used to drive the circuit.

Normal operation is restored when a normal reset is applied.

Power-Down Mode

To save even more power, a Power Down mode (see Table 2) can

be invoked by software. In this mode, the oscillator is stopped and

the instruction that invoked Power Down is the last instruction

executed. The on-chip RAM and Special Function Registers retain

Programmable Clock-Out

A 50% duty cycle clock can be programmed to come out on P1.0.

This pin, besides being a regular I/O pin, has two alternate

functions. It can be programmed:

their values down to 2.0 V and care must be taken to return V to

CC

the minimum specified operating voltages before the Power Down

Mode is terminated.

1. to input the external clock for Timer/Counter 2, or

Either a hardware reset or external interrupt can be used to exit from

Power Down. Reset redefines all the SFRs but does not change the

on-chip RAM. An external interrupt allows both the SFRs and the

on-chip RAM to retain their values.

2. to output a 50% duty cycle clock ranging from 122 Hz to 8 MHz at

a 16 MHz operating frequency (61 Hz to 4 MHz in 12 clock mode).

To configure the Timer/Counter 2 as a clock generator, bit C/T2 (in

T2CON) must be cleared and bit T20E in T2MOD must be set. Bit

TR2 (T2CON.2) also must be set to start the timer.

To properly terminate Power Down, the reset or external interrupt

should not be executed before V is restored to its normal

CC

operating level and must be held active long enough for the

oscillator to restart and stabilize (normally less than 10 ms).

The Clock-Out frequency depends on the oscillator frequency and

the reload value of Timer 2 capture registers (RCAP2H, RCAP2L)

as shown in this equation:

With an external interrupt, INT0 and INT1 must be enabled and

configured as level-sensitive. Holding the pin low restarts the oscillator

but bringing the pin back high completes the exit. Once the interrupt

is serviced, the next instruction to be executed after RETI will be the

one following the instruction that put the device into Power Down.

Oscillator Frequency

n (65536 * RCAP2H, RCAP2L)

n =

2 in 6 clock mode

4 in 12 clock mode

POWER OFF FLAG

The Power Off Flag (POF) is set by on-chip circuitry when the V

Where (RCAP2H,RCAP2L) = the content of RCAP2H and RCAP2L

taken as a 16-bit unsigned integer.

CC

level on the 89C51RB2/RC2/RD2 rises from 0 to 5 V. The POF bit

can be set or cleared by software allowing a user to determine if the

reset is the result of a power-on or a warm start after powerdown.

In the Clock-Out mode Timer 2 roll-overs will not generate an

interrupt. This is similar to when it is used as a baud-rate generator.

It is possible to use Timer 2 as a baud-rate generator and a clock

generator simultaneously. Note, however, that the baud-rate and the

Clock-Out frequency will be the same.

The V level must remain above 3 V for the POF to remain

CC

unaffected by the V level.

CC

Table 2. External Pin Status During Idle and Power-Down Mode

MODE

PROGRAM MEMORY

Internal

ALE

PSEN

PORT 0

Data

PORT 1

Data

PORT 2

Data

PORT 3

Data

Idle

1

0

1

0

External

Float

Data

Address

Data

Power-down

Internal

Data

External

Float

Data

10

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

Counter Enable) which is located in the T2MOD register (see

Figure 3). When reset is applied the DCEN=0 which means Timer 2

will default to counting up. If DCEN bit is set, Timer 2 can count up

or down depending on the value of the T2EX pin.

TIMER 2 OPERATION

Timer 2

Timer 2 is a 16-bit Timer/Counter which can operate as either an

event timer or an event counter, as selected by C/T2* in the special

function register T2CON (see Figure 1). Timer 2 has three operating

modes: Capture, Auto-reload (up or down counting), and Baud Rate

Generator, which are selected by bits in the T2CON as shown in

Table 3.

Figure 4 shows Timer 2 which will count up automatically since

DCEN=0. In this mode there are two options selected by bit EXEN2

in T2CON register. If EXEN2=0, then Timer 2 counts up to 0FFFFH

and sets the TF2 (Overflow Flag) bit upon overflow. This causes the

Timer 2 registers to be reloaded with the 16-bit value in RCAP2L

and RCAP2H. The values in RCAP2L and RCAP2H are preset by

software means.

Capture Mode

In the capture mode there are two options which are selected by bit

EXEN2 in T2CON. If EXEN2=0, then timer 2 is a 16-bit timer or

counter (as selected by C/T2* in T2CON) which, upon overflowing

sets bit TF2, the timer 2 overflow bit. This bit can be used to

generate an interrupt (by enabling the Timer 2 interrupt bit in the

IE register). If EXEN2= 1, Timer 2 operates as described above, but

with the added feature that a 1- to -0 transition at external input

T2EX causes the current value in the Timer 2 registers, TL2 and

TH2, to be captured into registers RCAP2L and RCAP2H,

respectively. In addition, the transition at T2EX causes bit EXF2 in

T2CON to be set, and EXF2 like TF2 can generate an interrupt

(which vectors to the same location as Timer 2 overflow interrupt.

The Timer 2 interrupt service routine can interrogate TF2 and EXF2

to determine which event caused the interrupt). The capture mode is

illustrated in Figure 2 (There is no reload value for TL2 and TH2 in

this mode. Even when a capture event occurs from T2EX, the

counter keeps on counting T2EX pin transitions or osc/6 pulses

(osc/12 in 12 clock mode).).

If EXEN2=1, then a 16-bit reload can be triggered either by an

overflow or by a 1-to-0 transition at input T2EX. This transition also

sets the EXF2 bit. The Timer 2 interrupt, if enabled, can be

generated when either TF2 or EXF2 are 1.

In Figure 5 DCEN=1 which enables Timer 2 to count up or down.

This mode allows pin T2EX to control the direction of count. When a

logic 1 is applied at pin T2EX Timer 2 will count up. Timer 2 will

overflow at 0FFFFH and set the TF2 flag, which can then generate

an interrupt, if the interrupt is enabled. This timer overflow also

causes the 16-bit value in RCAP2L and RCAP2H to be reloaded

into the timer registers TL2 and TH2.

When a logic 0 is applied at pin T2EX this causes Timer 2 to count

down. The timer will underflow when TL2 and TH2 become equal to

the value stored in RCAP2L and RCAP2H. Timer 2 underflow sets

the TF2 flag and causes 0FFFFH to be reloaded into the timer

registers TL2 and TH2.

Auto-Reload Mode (Up or Down Counter)

The external flag EXF2 toggles when Timer 2 underflows or overflows.

This EXF2 bit can be used as a 17th bit of resolution if needed. The

EXF2 flag does not generate an interrupt in this mode of operation.

In the 16-bit auto-reload mode, Timer 2 can be configured (as either

a timer or counter [C/T2* in T2CON]) then programmed to count up

or down. The counting direction is determined by bit DCEN (Down

(MSB)

(LSB)

TF2

EXF2

RCLK

TCLK

EXEN2

TR2

C/T2

CP/RL2

Symbol

Position

Name and Significance

TF2

T2CON.7

T2CON.6

Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set

when either RCLK or TCLK = 1.

EXF2

Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and

EXEN2 = 1. When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2

interrupt routine. EXF2 must be cleared by software. EXF2 does not cause an interrupt in up/down

counter mode (DCEN = 1).

RCLK

TCLK

T2CON.5

T2CON.4

T2CON.3

Receive clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock

in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock.

Transmit clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock

in modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.

EXEN2

Timer 2 external enable flag. When set, allows a capture or reload to occur as a result of a negative

transition on T2EX if Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to

ignore events at T2EX.

TR2

T2CON.2

T2CON.1

Start/stop control for Timer 2. A logic 1 starts the timer.

C/T2

Timer or counter select. (Timer 2)

0 = Internal timer (OSC/6 in 6 clock mode or OSC/12 in 12 clock mode)

1 = External event counter (falling edge triggered).

CP/RL2

T2CON.0

Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if EXEN2 = 1. When

cleared, auto-reloads will occur either with Timer 2 overflows or negative transitions at T2EX when

EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to auto-reload

on Timer 2 overflow.

SU01251

Figure 1. Timer/Counter 2 (T2CON) Control Register

11

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

Table 3. Timer 2 Operating Modes

RCLK + TCLK

CP/RL2

TR2

1

MODE

0

1

X

0

1

16-bit Auto-reload

1

16-bit Capture

Baud rate generator

(off)

X

1

0

OSC

÷ n*

C/T2 = 0

TL2

(8-bits)

TH2

(8-bits)

TF2

C/T2 = 1

T2 Pin

Control

TR2

Capture

Transition

Detector

Timer 2

Interrupt

RCAP2L

RCAP2H

T2EX Pin

EXF2

Control

EXEN2

SU01252

* n = 6 in 6 clock mode, or 12 in 12 clock mode.

Figure 2. Timer 2 in Capture Mode

T2MOD

Address = 0C9H

Not Bit Addressable

—

Reset Value = XXXX XX00B

—

6

—

5

—

4

—

3

—

2

T2OE

1

DCEN

0

Bit

7

Symbol

Function

—

Not implemented, reserved for future use.*

Timer 2 Output Enable bit.

T2OE

DCEN

Down Count Enable bit. When set, this allows Timer 2 to be configured as an up/down counter.

*

User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features.

In that case, the reset or inactive value of the new bit will be 0, and its active value will be 1. The value read from a reserved bit is

indeterminate.

SU00729

Figure 3. Timer 2 Mode (T2MOD) Control Register

12

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

OSC

÷ n*

C/T2 = 0

TL2

(8-BITS)

TH2

(8-BITS)

C/T2 = 1

T2 PIN

CONTROL

TR2

RELOAD

TRANSITION

DETECTOR

RCAP2L

RCAP2H

TF2

TIMER 2

INTERRUPT

T2EX PIN

EXF2

CONTROL

EXEN2

SU01253

* n = 6 in 6 clock mode, or 12 in 12 clock mode.

Figure 4. Timer 2 in Auto-Reload Mode (DCEN = 0)

(DOWN COUNTING RELOAD VALUE)

FFH

TOGGLE

EXF2

÷ n*

OSC

C/T2 = 0

C/T2 = 1

OVERFLOW

TL2

TH2

TF2

INTERRUPT

T2 PIN

CONTROL

TR2

COUNT

DIRECTION

1 = UP

0 = DOWN

RCAP2L

RCAP2H

(UP COUNTING RELOAD VALUE)

T2EX PIN

* n = 6 in 6 clock mode, or 12 in 12 clock mode.

SU01254

Figure 5. Timer 2 Auto Reload Mode (DCEN = 1)

13

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

Timer 1

Overflow

÷ 2

“0”

“1”

OSC

C/T2 = 0

SMOD

RCLK

“1”

TL2

(8-bits)

TH2

(8-bits)

C/T2 = 1

T2 Pin

Control

RX Clock

÷ 16

“1”

“0”

TR2

Reload

TCLK

Transition

Detector

RCAP2L

RCAP2H

TX Clock

Timer 2

Interrupt

T2EX Pin

EXF2

Control

EXEN2

Note availability of additional external interrupt.

SU01213

Figure 6. Timer 2 in Baud Rate Generator Mode

The baud rates in modes 1 and 3 are determined by Timer 2’s

overflow rate given below:

Table 4. Timer 2 Generated Commonly Used

Baud Rates

Timer 2 Overflow Rate

Modes 1 and 3 Baud Rates +

Baud Rate

Timer 2

16

Osc Freq

12 clock

mode

6 clock

mode

The timer can be configured for either “timer” or “counter” operation.

In many applications, it is configured for “timer” operation (C/T2*=0).

Timer operation is different for Timer 2 when it is being used as a

baud rate generator.

RCAP2H

RCAP2L

375 k

9.6 k

2.8 k

2.4 k

1.2 k

300

110

300

110

750 k

19.2 k

5.6 k

4.8 k

2.4 k

600

220

600

220

12 MHz

6 MHz

FF

FE

FB

F2

FD

F9

FF

D9

B2

64

C8

1E

AF

8F

57

Usually, as a timer it would increment every machine cycle (i.e.,

1

/ the oscillator frequency in 6 clock mode, / the oscillator

6

12

frequency in 12 clock mode). As a baud rate generator, it increments

OSC

at the oscillator frequency in 6 clock mode (

Thus the baud rate formula is as follows:

/ in 12 clock mode).

2

Modes 1 and 3 Baud Rates =

Oscillator Frequency

6 MHz

[ n * [65536 * (RCAP2H, RCAP2L)]]

Baud Rate Generator Mode

* n =

16 in 6 clock mode

32 in 12 clock mode

Bits TCLK and/or RCLK in T2CON (Table 4) allow the serial port

transmit and receive baud rates to be derived from either Timer 1 or

Timer 2. When TCLK= 0, Timer 1 is used as the serial port transmit

baud rate generator. When TCLK= 1, Timer 2 is used as the serial

port transmit baud rate generator. RCLK has the same effect for the

serial port receive baud rate. With these two bits, the serial port can

have different receive and transmit baud rates – one generated by

Timer 1, the other by Timer 2.

Where: (RCAP2H, RCAP2L)= The content of RCAP2H and

RCAP2L taken as a 16-bit unsigned integer.

The Timer 2 as a baud rate generator mode shown in Figure 6, is

valid only if RCLK and/or TCLK = 1 in T2CON register. Note that a

rollover in TH2 does not set TF2, and will not generate an interrupt.

Thus, the Timer 2 interrupt does not have to be disabled when

Timer 2 is in the baud rate generator mode. Also if the EXEN2

(T2 external enable flag) is set, a 1-to-0 transition in T2EX

(Timer/counter 2 trigger input) will set EXF2 (T2 external flag) but

will not cause a reload from (RCAP2H, RCAP2L) to (TH2,TL2).

Therefore when Timer 2 is in use as a baud rate generator, T2EX

can be used as an additional external interrupt, if needed.

Figure 6 shows the Timer 2 in baud rate generation mode. The baud

rate generation mode is like the auto-reload mode,in that a rollover in

TH2 causes the Timer 2 registers to be reloaded with the 16-bit value

in registers RCAP2H and RCAP2L, which are preset by software.

14

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

When Timer 2 is in the baud rate generator mode, one should not try

to read or write TH2 and TL2. As a baud rate generator, Timer 2 is

incremented every state time (osc/2) or asynchronously from pin T2;

under these conditions, a read or write of TH2 or TL2 may not be

accurate. The RCAP2 registers may be read, but should not be

written to, because a write might overlap a reload and cause write

and/or reload errors. The timer should be turned off (clear TR2)

before accessing the Timer 2 or RCAP2 registers.

If Timer 2 is being clocked internally, the baud rate is:

f_OSC

Baud Rate +

[ n * [65536 * (RCAP2H, RCAP2L)]]

* n =

16 in 6 clock mode

32 in 12 clock mode

Where f

= Oscillator Frequency

OSC

To obtain the reload value for RCAP2H and RCAP2L, the above

equation can be rewritten as:

Table 4 shows commonly used baud rates and how they can be

obtained from Timer 2.

f_OSC

Summary of Baud Rate Equations

Timer 2 is in baud rate generating mode. If Timer 2 is being clocked

through pin T2(P1.0) the baud rate is:

_{RCAP2H, RCAP2L + 65536 *}ǒ

Ǔ

n * Baud Rate

Timer/Counter 2 Set-up

Timer 2 Overflow Rate

Baud Rate +

Except for the baud rate generator mode, the values given for T2CON

do not include the setting of the TR2 bit. Therefore, bit TR2 must be

set, separately, to turn the timer on. see Table 5 for set-up of Timer 2

as a timer. Also see Table 6 for set-up of Timer 2 as a counter.

16

Table 5. Timer 2 as a Timer

T2CON

MODE

INTERNAL CONTROL

(Note 1)

EXTERNAL CONTROL

(Note 2)

16-bit Auto-Reload

00H

01H

34H

24H

14H

08H

09H

36H

26H

16H

16-bit Capture

Baud rate generator receive and transmit same baud rate

Receive only

Transmit only

Table 6. Timer 2 as a Counter

TMOD

MODE

INTERNAL CONTROL

(Note 1)

EXTERNAL CONTROL

(Note 2)

16-bit

02H

03H

0AH

0BH

Auto-Reload

NOTES:

1. Capture/reload occurs only on timer/counter overflow.

2. Capture/reload occurs on timer/counter overflow and a 1-to-0 transition on T2EX (P1.1) pin except when Timer 2 is used in the baud rate

generator mode.

15

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

Slave 1

SADDR

SADEN

Given

=

1100 0000

1111 1110

1100 000X

Enhanced UART

The UART operates in all of the usual modes that are described in

the first section of Data Handbook IC20, 80C51-Based 8-Bit

Microcontrollers. In addition the UART can perform framing error

In the above example SADDR is the same and the SADEN data is

used to differentiate between the two slaves. Slave 0 requires a 0 in

bit 0 and it ignores bit 1. Slave 1 requires a 0 in bit 1 and bit 0 is

ignored. A unique address for Slave 0 would be 1100 0010 since

slave 1 requires a 0 in bit 1. A unique address for slave 1 would be

1100 0001 since a 1 in bit 0 will exclude slave 0. Both slaves can be

selected at the same time by an address which has bit 0 = 0 (for

slave 0) and bit 1 = 0 (for slave 1). Thus, both could be addressed

with 1100 0000.

detect by looking for missing stop bits, and automatic address

recognition. The UART also fully supports multiprocessor

communication as does the standard 80C51 UART.

When used for framing error detect the UART looks for missing stop

bits in the communication. A missing bit will set the FE bit in the

SCON register. The FE bit shares the SCON.7 bit with SM0 and the

function of SCON.7 is determined by PCON.6 (SMOD0) (see

Figure 7). If SMOD0 is set then SCON.7 functions as FE. SCON.7

functions as SM0 when SMOD0 is cleared. When used as FE

SCON.7 can only be cleared by software. Refer to Figure 8.

In a more complex system the following could be used to select

slaves 1 and 2 while excluding slave 0:

Automatic Address Recognition

Slave 0

Slave 1

Slave 2

SADDR

SADEN

Given

=

1100 0000

1111 1001

1100 0XX0

Automatic Address Recognition is a feature which allows the UART

to recognize certain addresses in the serial bit stream by using

hardware to make the comparisons. This feature saves a great deal

of software overhead by eliminating the need for the software to

examine every serial address which passes by the serial port. This

feature is enabled by setting the SM2 bit in SCON. In the 9 bit UART

modes, mode 2 and mode 3, the Receive Interrupt flag (RI) will be

automatically set when the received byte contains either the “Given”

address or the “Broadcast” address. The 9-bit mode requires that

the 9th information bit is a 1 to indicate that the received information

is an address and not data. Automatic address recognition is shown

in Figure 9.

SADDR

SADEN

Given

=

1110 0000

1111 1010

1110 0X0X

SADDR

SADEN

Given

=

1110 0000

1111 1100

1110 00XX

In the above example the differentiation among the 3 slaves is in the

lower 3 address bits. Slave 0 requires that bit 0 = 0 and it can be

uniquely addressed by 1110 0110. Slave 1 requires that bit 1 = 0 and

it can be uniquely addressed by 1110 and 0101. Slave 2 requires

that bit 2 = 0 and its unique address is 1110 0011. To select Slaves 0

and 1 and exclude Slave 2 use address 1110 0100, since it is

necessary to make bit 2 = 1 to exclude slave 2.

The 8 bit mode is called Mode 1. In this mode the RI flag will be set

if SM2 is enabled and the information received has a valid stop bit

following the 8 address bits and the information is either a Given or

Broadcast address.

Mode 0 is the Shift Register mode and SM2 is ignored.

The Broadcast Address for each slave is created by taking the

logical OR of SADDR and SADEN. Zeros in this result are trended

as don’t-cares. In most cases, interpreting the don’t-cares as ones,

the broadcast address will be FF hexadecimal.

Using the Automatic Address Recognition feature allows a master to

selectively communicate with one or more slaves by invoking the

Given slave address or addresses. All of the slaves may be

contacted by using the Broadcast address. Two special Function

Registers are used to define the slave’s address, SADDR, and the

address mask, SADEN. SADEN is used to define which bits in the

SADDR are to b used and which bits are “don’t care”. The SADEN

mask can be logically ANDed with the SADDR to create the “Given”

address which the master will use for addressing each of the slaves.

Use of the Given address allows multiple slaves to be recognized

while excluding others. The following examples will help to show the

versatility of this scheme:

Upon reset SADDR (SFR address 0A9H) and SADEN (SFR

address 0B9H) are leaded with 0s. This produces a given address

of all “don’t cares” as well as a Broadcast address of all “don’t

cares”. This effectively disables the Automatic Addressing mode and

allows the microcontroller to use standard 80C51 type UART drivers

which do not make use of this feature.

Slave 0

SADDR

SADEN

Given

=

1100 0000

1111 1101

1100 00X0

16

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

SCON Address = 98H

Reset Value = 0000 0000B

Bit Addressable

SM0/FE

SM1

SM2

REN

TB8

RB8

Tl

Rl

Bit:

7

6

5

4

3

2

1

0

(SMOD0 = 0/1)*

Symbol

FE

Function

Framing Error bit. This bit is set by the receiver when an invalid stop bit is detected. The FE bit is not cleared by valid

frames but should be cleared by software. The SMOD0 bit must be set to enable access to the FE bit.

SM0

SM1

Serial Port Mode Bit 0, (SMOD0 must = 0 to access bit SM0)

Serial Port Mode Bit 1

SM0

SM1

Mode

Description

Baud Rate**

0

1

0

1

0

1

2

shift register

8-bit UART

9-bit UART

f

/6 (6 clock mode) or f

/12 (12 clock mode)

OSC

variable

f

/32 or f

/64 or f

/16 (6 clock mode) or

/32 (12 clock mode)

OSC

1

3

9-bit UART

variable

SM2

Enables the Automatic Address Recognition feature in Modes 2 or 3. If SM2 = 1 then Rl will not be set unless the

received 9th data bit (RB8) is 1, indicating an address, and the received byte is a Given or Broadcast Address.

In Mode 1, if SM2 = 1 then Rl will not be activated unless a valid stop bit was received, and the received byte is a

Given or Broadcast Address. In Mode 0, SM2 should be 0.

REN

TB8

RB8

Enables serial reception. Set by software to enable reception. Clear by software to disable reception.

The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired.

In modes 2 and 3, the 9th data bit that was received. In Mode 1, if SM2 = 0, RB8 is the stop bit that was received.

In Mode 0, RB8 is not used.

Tl

Transmit interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the beginning of the stop bit in the

other modes, in any serial transmission. Must be cleared by software.

Rl

Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or halfway through the stop bit time in

the other modes, in any serial reception (except see SM2). Must be cleared by software.

NOTE:

*SMOD0 is located at PCON6.

**f = oscillator frequency

OSC

SU01255

Figure 7. SCON: Serial Port Control Register

17

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

D0

D1

D2

D3

D4

D5

D6

D7

D8

START

BIT

DATA BYTE

ONLY IN

MODE 2, 3

STOP

BIT

SET FE BIT IF STOP BIT IS 0 (FRAMING ERROR)

SM0 TO UART MODE CONTROL

SCON

(98H)

SM0 / FE

SMOD1

SM1

SM2

REN

POF

TB8

LVF

RB8

GF0

TI

RI

PCON

(87H)

SMOD0

–

GF1

IDL

0 : SCON.7 = SM0

1 : SCON.7 = FE

SU00044

Figure 8. UART Framing Error Detection

D0

D1

D2

D3

D4

D5

D6

D7

D8

SCON

(98H)

SM0

SM1

SM2

REN

1

TB8

X

RB8

TI

RI

1

0

1

RECEIVED ADDRESS D0 TO D7

PROGRAMMED ADDRESS

COMPARATOR

IN UART MODE 2 OR MODE 3 AND SM2 = 1:

INTERRUPT IF REN=1, RB8=1 AND “RECEIVED ADDRESS” = “PROGRAMMED ADDRESS”

– WHEN OWN ADDRESS RECEIVED, CLEAR SM2 TO RECEIVE DATA BYTES

– WHEN ALL DATA BYTES HAVE BEEN RECEIVED: SET SM2 TO WAIT FOR NEXT ADDRESS.

SU00045

Figure 9. UART Multiprocessor Communication, Automatic Address Recognition

18

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

The priority scheme for servicing the interrupts is the same as that

for the 80C51, except there are four interrupt levels rather than two

as on the 80C51. An interrupt will be serviced as long as an interrupt

of equal or higher priority is not already being serviced. If an

interrupt of equal or higher level priority is being serviced, the new

interrupt will wait until it is finished before being serviced. If a lower

priority level interrupt is being serviced, it will be stopped and the

new interrupt serviced. When the new interrupt is finished, the lower

priority level interrupt that was stopped will be completed.

Interrupt Priority Structure

The 89C51RB2/RC2/RD2 has an 8 source four-level interrupt

structure (see Table 7).

There are 3 SFRs associated with the four-level interrupt. They are

the IE, IP, and IPH. (See Figures 10, 11, and 12.) The IPH (Interrupt

Priority High) register makes the four-level interrupt structure

possible. The IPH is located at SFR address B7H. The structure of

the IPH register and a description of its bits is shown in Figure 12.

The function of the IPH SFR is simple and when combined with the

IP SFR determines the priority of each interrupt. The priority of each

interrupt is determined as shown in the following table:

PRIORITY BITS

INTERRUPT PRIORITY LEVEL

IPH.x

IP.x

0

1

Level 0 (lowest priority)

Level 1

1

0

Level 2

1

Level 3 (highest priority)

Table 7.

Interrupt Table

SOURCE

POLLING PRIORITY

REQUEST BITS

HARDWARE CLEAR?

VECTOR ADDRESS

1

2

X0

T0

1

2

3

4

5

IE0

TP0

IE1

N (L) Y (T)

03H

0BH

13H

1BH

33H

Y

X1

N (L) Y (T)

T1

TF1

Y

N

PCA

CF, CCFn

n = 0–4

SP

T2

6

7

RI, TI

N

23H

2BH

TF2, EXF2

NOTES:

1. L = Level activated

2. T = Transition activated

7

6

5

4

3

2

1

0

IE (0A8H)

EA

EC

ET2

ES

ET1

EX1

ET0

EX0

Enable Bit = 1 enables the interrupt.

Enable Bit = 0 disables it.

BIT

SYMBOL FUNCTION

IE.7

EA

Global disable bit. If EA = 0, all interrupts are disabled. If EA = 1, each interrupt can be individually

enabled or disabled by setting or clearing its enable bit.

PCA interrupt enable bit

Timer 2 interrupt enable bit.

Serial Port interrupt enable bit.

Timer 1 interrupt enable bit.

External interrupt 1 enable bit.

Timer 0 interrupt enable bit.

IE.6

IE.5

IE.4

IE.3

IE.2

IE.1

IE.0

EC

ET2

ES

ET1

EX1

ET0

EX0

External interrupt 0 enable bit.

SU01290

Figure 10. IE Registers

19

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

7

6

5

4

3

2

1

0

IP (0B8H)

–

PPC

PT2

PS

PT1

PX1

PT0

PX0

Priority Bit = 1 assigns high priority

Priority Bit = 0 assigns low priority

BIT

IP.7

IP.6

IP.5

IP.4

IP.3

IP.2

IP.1

IP.0

SYMBOL FUNCTION

–

PPC

PT2

PS

PT1

PX1

PT0

PX0

PCA interrupt priority bit

Timer 2 interrupt priority bit.

Serial Port interrupt priority bit.

Timer 1 interrupt priority bit.

External interrupt 1 priority bit.

Timer 0 interrupt priority bit.

External interrupt 0 priority bit.

SU01291

Figure 11. IP Registers

7

6

5

4

3

2

1

0

IPH (B7H)

–

PPCH

PT2H

PSH

PT1H

PX1H

PT0H

PX0H

Priority Bit = 1 assigns higher priority

Priority Bit = 0 assigns lower priority

BIT

SYMBOL FUNCTION

IPH.7

IPH.6

IPH.5

IPH.4

IPH.3

IPH.2

IPH.1

IPH.0

–

PPCH

PT2H

PSH

PT1H

PX1H

PT0H

PX0H

PCA interrupt priority bit

Timer 2 interrupt priority bit high.

Serial Port interrupt priority bit high.

Timer 1 interrupt priority bit high.

External interrupt 1 priority bit high.

Timer 0 interrupt priority bit high.

External interrupt 0 priority bit high.

SU01292

Figure 12. IPH Registers

20

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

be quickly toggled simply by executing an INC AUXR1 instruction

without affecting the GF2 bit.

Reduced EMI Mode

The AO bit (AUXR.0) in the AUXR register when set disables the

ALE output.

The ENBOOT bit determines whether the BOOTROM is enabled

or disabled. This bit will automatically be set if the status byte is

non zero during reset or PSEN is pulled low, ALE floats high, and

Reduced EMI Mode

EA > V on the falling edge of reset. Otherwise, this bit will be

cleared during reset.

IH

AUXR (8EH)

7

–

6

–

5

–

4

–

3

–

2

–

1

0

EXTRAM

AO

AUXR.1

AUXR.0

EXTRAM

AO

DPS

BIT0

Turns off ALE output.

AUXR1

DPTR1

DPTR0

Dual DPTR

DPH

DPL

The dual DPTR structure (see Figure 13) is a way by which the chip

will specify the address of an external data memory location. There

are two 16-bit DPTR registers that address the external memory,

and a single bit called DPS = AUXR1/bit0 that allows the program

code to switch between them.

(83H)

(82H)

EXTERNAL

DATA

MEMORY

SU00745A

Figure 13.

• New Register Name: AUXR1#

• SFR Address: A2H

DPTR Instructions

• Reset Value: xxxxxxx0B

The instructions that refer to DPTR refer to the data pointer that is

currently selected using the AUXR1/bit 0 register. The six

instructions that use the DPTR are as follows:

AUXR1 (A2H)

7

–

6

–

5

4

–

3

2

0

1

–

0

INC DPTR

Increments the data pointer by 1

ENBOOT

GF2

DPS

MOV DPTR, #data16 Loads the DPTR with a 16-bit constant

Where:

DPS = AUXR1/bit0 = Switches between DPTR0 and DPTR1.

MOV A, @ A+DPTR

MOVX A, @ DPTR

Move code byte relative to DPTR to ACC

Move external RAM (16-bit address) to

ACC

Select Reg

DPS

DPTR0

DPTR1

0

1

MOVX @ DPTR , A

JMP @ A + DPTR

Move ACC to external RAM (16-bit

address)

Jump indirect relative to DPTR

The DPS bit status should be saved by software when switching

between DPTR0 and DPTR1.

The data pointer can be accessed on a byte-by-byte basis by

specifying the low or high byte in an instruction which accesses the

SFRs. See Application Note AN458 for more details.

The GF2 bit is a general purpose user-defined flag. Note that bit 2 is

not writable and is always read as a zero. This allows the DPS bit to

21

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

the PCA counter overflows and an interrupt will be generated if the

ECF bit in the CMOD register is set, The CF bit can only be cleared

by software. Bits 0 through 4 of the CCON register are the flags for

the modules (bit 0 for module 0, bit 1 for module 1, etc.) and are set

by hardware when either a match or a capture occurs. These flags

also can only be cleared by software. The PCA interrupt system

shown in Figure 16.

Programmable Counter Array (PCA)

The Programmable Counter Array available on the

89C51RB2/RC2/RD2 is a special 16-bit Timer that has five 16-bit

capture/compare modules associated with it. Each of the modules

can be programmed to operate in one of four modes: rising and/or

falling edge capture, software timer, high-speed output, or pulse

width modulator. Each module has a pin associated with it in port 1.

Module 0 is connected to P1.3(CEX0), module 1 to P1.4(CEX1), etc.

The basic PCA configuration is shown in Figure 14.

Each module in the PCA has a special function register associated

with it. These registers are: CCAPM0 for module 0, CCAPM1 for

module 1, etc. (see Figure 19). The registers contain the bits that

control the mode that each module will operate in. The ECCF bit

(CCAPMn.0 where n=0, 1, 2, 3, or 4 depending on the module)

enables the CCF flag in the CCON SFR to generate an interrupt

when a match or compare occurs in the associated module. PWM

(CCAPMn.1) enables the pulse width modulation mode. The TOG

bit (CCAPMn.2) when set causes the CEX output associated with

the module to toggle when there is a match between the PCA

counter and the module’s capture/compare register. The match bit

MAT (CCAPMn.3) when set will cause the CCFn bit in the CCON

register to be set when there is a match between the PCA counter

and the module’s capture/compare register.

The PCA timer is a common time base for all five modules and can

be programmed to run at: 1/6 the oscillator frequency, 1/2 the

oscillator frequency, the Timer 0 overflow, or the input on the ECI pin

(P1.2). The timer count source is determined from the CPS1 and

CPS0 bits in the CMOD SFR as follows (see Figure 17):

CPS1 CPS0 PCA Timer Count Source

0

1/6 oscillator frequency (6 clock mode);

1/12 oscillator frequency (12 clock mode)

1/2 oscillator frequency (6 clock mode);

1/4 oscillator frequency (12 clock mode)

Timer 0 overflow

0

1

0

1

External Input at ECI pin

The next two bits CAPN (CCAPMn.4) and CAPP (CCAPMn.5)

determine the edge that a capture input will be active on. The CAPN

bit enables the negative edge, and the CAPP bit enables the positive

edge. If both bits are set both edges will be enabled and a capture will

occur for either transition. The last bit in the register ECOM

(CCAPMn.6) when set enables the comparator function. Figure 20

shows the CCAPMn settings for the various PCA functions.

In the CMOD SFR are three additional bits associated with the PCA.

They are CIDL which allows the PCA to stop during idle mode,

WDTE which enables or disables the watchdog function on

module 4, and ECF which when set causes an interrupt and the

PCA overflow flag CF (in the CCON SFR) to be set when the PCA

timer overflows. These functions are shown in Figure 15.

The watchdog timer function is implemented in module 4 (see

Figure 24).

There are two additional registers associated with each of the PCA

modules. They are CCAPnH and CCAPnL and these are the

registers that store the 16-bit count when a capture occurs or a

compare should occur. When a module is used in the PWM mode

these registers are used to control the duty cycle of the output.

The CCON SFR contains the run control bit for the PCA and the

flags for the PCA timer (CF) and each module (refer to Figure 18).

To run the PCA the CR bit (CCON.6) must be set by software. The

PCA is shut off by clearing this bit. The CF bit (CCON.7) is set when

16 BITS

P1.3/CEX0

P1.4/CEX1

P1.5/CEX2

P1.6/CEX3

MODULE 0

MODULE 1

MODULE 2

MODULE 3

MODULE 4

16 BITS

PCA TIMER/COUNTER

TIME BASE FOR PCA MODULES

MODULE FUNCTIONS:

16-BIT CAPTURE

16-BIT TIMER

P1.7/CEX4

SU00032

16-BIT HIGH SPEED OUTPUT

8-BIT PWM

WATCHDOG TIMER (MODULE 4 ONLY)

Figure 14. Programmable Counter Array (PCA)

22

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

TO PCA

MODULES

OSC/6 (6 CLOCK MODE)

OR

OSC/12 (12 CLOCK MODE)

OSC/2 (6 CLOCK MODE)

OR

OSC/4 (12 CLOCK MODE)

OVERFLOW

INTERRUPT

CH

CL

16–BIT UP COUNTER

TIMER 0 OVERFLOW

EXTERNAL INPUT

(P1.2/ECI)

00

01

10

11

DECODE

IDLE

CMOD

(C1H)

CIDL

CF

WDTE

––

CPS1

CCF2

CPS0

ECF

CCON

(C0H)

CR

CCF4

CCF3

CCF1

CCF0

SU01256

Figure 15. PCA Timer/Counter

CCON

(C0H)

CF

CR

––

CCF4

CCF3

CCF2

CCF1

CCF0

PCA TIMER/COUNTER

MODULE 0

IE.7

EA

IE.6

EC

TO

MODULE 1

MODULE 2

INTERRUPT

PRIORITY

DECODER

MODULE 3

MODULE 4

CCAPMn.0

ECCFn

CMOD.0

ECF

SU01097

Figure 16. PCA Interrupt System

23

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

CMOD Address = C1H

Reset Value = 00XX X000B

CIDL

WDTE

–

CPS1

CPS0

ECF

Bit:

Function

7

6

5

4

3

2

1

0

Symbol

CIDL

Counter Idle control: CIDL = 0 programs the PCA Counter to continue functioning during idle Mode. CIDL = 1 programs

it to be gated off during idle.

WDTE

–

Watchdog Timer Enable: WDTE = 0 disables Watchdog Timer function on PCA Module 4. WDTE = 1 enables it.

Not implemented, reserved for future use.*

CPS1

CPS0

PCA Count Pulse Select bit 1.

PCA Count Pulse Select bit 0.

CPS1

CPS0

Selected PCA Input**

0

1

0

1

0

1

0

1

2

3

Internal clock, f

/6 in 6 clock mode (f

/2 in 6 clock mode (f

/12 in 12 clock mode)

/4 in 12 clock mode)

OSC

Internal clock, f

OSC

Timer 0 overflow

External clock at ECI/P1.2 pin

(max. rate = f /4 in 6 clock mode, f

/8 in 12 clock mode)

OCS

OSC

ECF

PCA Enable Counter Overflow interrupt: ECF = 1 enables CF bit in CCON to generate an interrupt. ECF = 0 disables

that function of CF.

NOTE:

*

User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features. In that case, the reset or inactive value of the

new bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.

**

f

= oscillator frequency

OSC

SU01257

Figure 17. CMOD: PCA Counter Mode Register

CCON Address = 0C0H

Reset Value = 00X0 0000B

Bit Addressable

CF

CR

–

CCF4

CCF3

CCF2

CCF1

CCF0

Bit:

7

6

5

4

3

2

1

0

Symbol

CF

Function

PCA Counter Overflow flag. Set by hardware when the counter rolls over. CF flags an interrupt if bit ECF in CMOD is

set. CF may be set by either hardware or software but can only be cleared by software.

CR

PCA Counter Run control bit. Set by software to turn the PCA counter on. Must be cleared by software to turn the PCA

counter off.

–

Not implemented, reserved for future use*.

CCF4

CCF3

CCF2

CCF1

CCF0

PCA Module 4 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.

PCA Module 3 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.

PCA Module 2 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.

PCA Module 1 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.

PCA Module 0 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.

NOTE:

*

User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features. In that case, the reset or inactive value of the

new bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.

SU01099

Figure 18. CCON: PCA Counter Control Register

24

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

CCAPMn Address

CCAPM0

CCAPM1

CCAPM2

CCAPM3

CCAPM4

0C2H

0C3H

0C4H

0C5H

0C6H

Reset Value = X000 0000B

Not Bit Addressable

–

ECOMn CAPPn

CAPNn

MATn

TOGn

PWMn

ECCFn

Bit:

7

6

5

4

3

2

1

0

Symbol

Function

–

Not implemented, reserved for future use*.

ECOMn

CAPPn

CAPNn

MATn

Enable Comparator. ECOMn = 1 enables the comparator function.

Capture Positive, CAPPn = 1 enables positive edge capture.

Capture Negative, CAPNn = 1 enables negative edge capture.

Match. When MATn = 1, a match of the PCA counter with this module’s compare/capture register causes the CCFn bit

in CCON to be set, flagging an interrupt.

TOGn

Toggle. When TOGn = 1, a match of the PCA counter with this module’s compare/capture register causes the CEXn

pin to toggle.

PWMn

ECCFn

Pulse Width Modulation Mode. PWMn = 1 enables the CEXn pin to be used as a pulse width modulated output.

Enable CCF interrupt. Enables compare/capture flag CCFn in the CCON register to generate an interrupt.

NOTE:

*User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features. In that case, the reset or inactive value of the new

bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.

SU01100

Figure 19. CCAPMn: PCA Modules Compare/Capture Registers

–

X

ECOMn CAPPn CAPNn

MATn

TOGn

PWMn

ECCFn

MODULE FUNCTION

0

X

1

0

1

0

1

0

1

0

1

0

1

0

1

0

X

0

1

0

X

0

No operation

16-bit capture by a positive-edge trigger on CEXn

16-bit capture by a negative trigger on CEXn

16-bit capture by a transition on CEXn

16-bit Software Timer

16-bit High Speed Output

8-bit PWM

X

Watchdog Timer

Figure 20. PCA Module Modes (CCAPMn Register)

PCA Capture Mode

counter and the module’s capture registers. To activate this mode

the TOG, MAT, and ECOM bits in the module’s CCAPMn SFR must

be set (see Figure 23).

To use one of the PCA modules in the capture mode either one or

both of the CCAPM bits CAPN and CAPP for that module must be

set. The external CEX input for the module (on port 1) is sampled for

a transition. When a valid transition occurs the PCA hardware loads

the value of the PCA counter registers (CH and CL) into the

module’s capture registers (CCAPnL and CCAPnH). If the CCFn bit

for the module in the CCON SFR and the ECCFn bit in the CCAPMn

SFR are set then an interrupt will be generated. Refer to Figure 21.

Pulse Width Modulator Mode

All of the PCA modules can be used as PWM outputs. Figure 24

shows the PWM function. The frequency of the output depends on

the source for the PCA timer. All of the modules will have the same

frequency of output because they all share the PCA timer. The duty

cycle of each module is independently variable using the module’s

capture register CCAPLn. When the value of the PCA CL SFR is

less than the value in the module’s CCAPLn SFR the output will be

low, when it is equal to or greater than the output will be high. When

CL overflows from FF to 00, CCAPLn is reloaded with the value in

CCAPHn. the allows updating the PWM without glitches. The PWM

and ECOM bits in the module’s CCAPMn register must be set to

enable the PWM mode.

16-bit Software Timer Mode

The PCA modules can be used as software timers by setting both

the ECOM and MAT bits in the modules CCAPMn register. The PCA

timer will be compared to the module’s capture registers and when a

match occurs an interrupt will occur if the CCFn (CCON SFR) and

the ECCFn (CCAPMn SFR) bits for the module are both set (see

Figure 22).

High Speed Output Mode

In this mode the CEX output (on port 1) associated with the PCA

module will toggle each time a match occurs between the PCA

25

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

CCON

(0C0H)

CF

CR

––

CCF4

CCF3

CCF2

CCF1

CCF0

PCA INTERRUPT

(TO CCFn)

PCA TIMER/COUNTER

CH

CL

CAPTURE

CEXn

CCAPnH

CCAPnL

CCAPMn, n= 0 to 4

(C2H – C6H)

––

ECOMn

0

CAPPn

CAPNn

MATn

0

TOGn

0

PWMn

ECCFn

0

SU01101

Figure 21. PCA Capture Mode

CCON

(C0H)

CF

CR

––

CCF4

CCF3

CCF2

CCF1

CCF0

WRITE TO

CCAPnH

RESET

PCA INTERRUPT

CCAPnH

CCAPnL

WRITE TO

CCAPnL

(TO CCFn)

0

1

ENABLE

MATCH

16–BIT COMPARATOR

CH

CL

PCA TIMER/COUNTER

CCAPMn, n= 0 to 4

(C2H – C6H)

––

ECOMn

CAPPn

0

CAPNn

0

MATn

TOGn

0

PWMn

0

ECCFn

SU01102

Figure 22. PCA Compare Mode

26

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

CCON

(C0H)

CF

CR

––

CCF4

CCF3

CCF2

CCF1

CCF0

WRITE TO

CCAPnH

RESET

PCA INTERRUPT

CCAPnH

CCAPnL

WRITE TO

CCAPnL

(TO CCFn)

0

1

MATCH

ENABLE

16–BIT COMPARATOR

TOGGLE

CEXn

CH

CL

PCA TIMER/COUNTER

CCAPMn, n: 0..4

(C2H – C6H)

––

ECOMn

CAPPn

0

CAPNn

0

MATn

TOGn

PWMn

0

ECCFn

1

SU01103

Figure 23. PCA High Speed Output Mode

CCAPnH

CCAPnL

0

CL < CCAPnL

ENABLE

8–BIT

CEXn

COMPARATOR

CL >= CCAPnL

1

CL

OVERFLOW

PCA TIMER/COUNTER

CCAPMn, n: 0..4

(C2H – C6H)

––

ECOMn

CAPPn

0

CAPNn

MATn

0

TOGn

0

PWMn

ECCFn

0

SU01104

Figure 24. PCA PWM Mode

27

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

CMOD

(C1H)

CIDL

WDTE

––

MODULE 4

MATCH

––

CPS1

CPS0

ECF

WRITE TO

CCAP4L

RESET

CCAP4H

CCAP4L

WRITE TO

CCAP4H

1

0

ENABLE

16–BIT COMPARATOR

RESET

CH

CL

PCA TIMER/COUNTER

CCAPM4

(C6H)

––

ECOMn

CAPPn

0

CAPNn

0

MATn

1

TOGn

X

PWMn

0

ECCFn

X

SU01105

Figure 25. PCA Watchdog Timer m(Module 4 only)

PCA Watchdog Timer

The first two options are more reliable because the watchdog

timer is never disabled as in option #3. If the program counter ever

goes astray, a match will eventually occur and cause an internal

reset. The second option is also not recommended if other PCA

modules are being used. Remember, the PCA timer is the time

base for all modules; changing the time base for other modules

would not be a good idea. Thus, in most applications the first

solution is the best option.

An on-board watchdog timer is available with the PCA to improve the

reliability of the system without increasing chip count. Watchdog

timers are useful for systems that are susceptible to noise, power

glitches, or electrostatic discharge. Module 4 is the only PCA module

that can be programmed as a watchdog. However, this module can

still be used for other modes if the watchdog is not needed.

Figure 25 shows a diagram of how the watchdog works. The user

pre-loads a 16-bit value in the compare registers. Just like the other

compare modes, this 16-bit value is compared to the PCA timer

value. If a match is allowed to occur, an internal reset will be

generated. This will not cause the RST pin to be driven high.

Figure 26 shows the code for initializing the watchdog timer.

Module 4 can be configured in either compare mode, and the WDTE

bit in CMOD must also be set. The user’s software then must

periodically change (CCAP4H,CCAP4L) to keep a match from

occurring with the PCA timer (CH,CL). This code is given in the

WATCHDOG routine in Figure 26.

In order to hold off the reset, the user has three options:

1. periodically change the compare value so it will never match the

PCA timer,

This routine should not be part of an interrupt service routine,

because if the program counter goes astray and gets stuck in an

infinite loop, interrupts will still be serviced and the watchdog will

keep getting reset. Thus, the purpose of the watchdog would be

2. periodically change the PCA timer value so it will never match

the compare values, or

3. disable the watchdog by clearing the WDTE bit before a match

occurs and then re-enable it.

defeated. Instead, call this subroutine from the main program within

16

2

count of the PCA timer.

28

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

INIT_WATCHDOG:

MOV CCAPM4, #4CH

MOV CCAP4L, #0FFH

MOV CCAP4H, #0FFH

; Module 4 in compare mode

; Write to low byte first

; Before PCA timer counts up to

; FFFF Hex, these compare values

; must be changed

ORL CMOD, #40H

; Set the WDTE bit to enable the

; watchdog timer without changing

; the other bits in CMOD

;

;********************************************************************

;

; Main program goes here, but CALL WATCHDOG periodically.

;

;********************************************************************

;

WATCHDOG:

CLR EA

; Hold off interrupts

MOV CCAP4L, #00

MOV CCAP4H, CH

SETB EA

; Next compare value is within

; 255 counts of the current PCA

; timer value

RET

Figure 26. PCA Watchdog Timer Initialization Code

29

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

For example:

MOV @R0,#data

Expanded Data RAM Addressing

The 89C51RB2/RC2/RD2 has internal data memory that is mapped

into four separate segments: the lower 128 bytes of RAM, upper 128

bytes of RAM, 128 bytes Special Function Register (SFR), and

256 bytes expanded RAM (ERAM) (768 bytes for the RD2).

where R0 contains 0A0H, accesses the data byte at address 0A0H,

rather than P2 (whose address is 0A0H).

The ERAM can be accessed by indirect addressing, with EXTRAM

bit cleared and MOVX instructions. This part of memory is physically

located on-chip, logically occupies the first 7936-bytes of external

data memory.

The four segments are:

1. The Lower 128 bytes of RAM (addresses 00H to 7FH) are

directly and indirectly addressable.

2. The Upper 128 bytes of RAM (addresses 80H to FFH) are

indirectly addressable only.

With EXTRAM = 0, the ERAM is indirectly addressed, using the

MOVX instruction in combination with any of the registers R0, R1 of

the selected bank or DPTR. An access to ERAM will not affect ports

P0, P3.6 (WR#) and P3.7 (RD#). P2 SFR is output during external

addressing. For example, with EXTRAM = 0,

3. The Special Function Registers, SFRs, (addresses 80H to FFH)

are directly addressable only.

4. The 256/768-bytes expanded RAM (ERAM, 00H – 1FFH/2FFH)

are indirectly accessed by move external instruction, MOVX, and

with the EXTRAM bit cleared, see Figure 27.

MOVX @R0,#data

where R0 contains 0A0H, access the ERAM at address 0A0H rather

than external memory. An access to external data memory locations

higher than the ERAM will be performed with the MOVX DPTR

instructions in the same way as in the standard 80C51, so with P0

and P2 as data/address bus, and P3.6 and P3.7 as write and read

timing signals. Refer to Figure 28.

The Lower 128 bytes can be accessed by either direct or indirect

addressing. The Upper 128 bytes can be accessed by indirect

addressing only. The Upper 128 bytes occupy the same address

space as the SFR. That means they have the same address, but are

physically separate from SFR space.

With EXTRAM = 1, MOVX @Ri and MOVX @DPTR will be similar

to the standard 80C51. MOVX @ Ri will provide an 8-bit address

multiplexed with data on Port 0 and any output port pins can be

used to output higher order address bits. This is to provide the

external paging capability. MOVX @DPTR will generate a 16-bit

address. Port 2 outputs the high-order eight address bits (the

contents of DPH) while Port 0 multiplexes the low-order eight

address bits (DPL) with data. MOVX @Ri and MOVX @DPTR will

generate either read or write signals on P3.6 (WR) and P3.7 (RD).

When an instruction accesses an internal location above address

7FH, the CPU knows whether the access is to the upper 128 bytes

of data RAM or to SFR space by the addressing mode used in the

instruction. Instructions that use direct addressing access SFR

space. For example:

MOV 0A0H,#data

accesses the SFR at location 0A0H (which is P2). Instructions that

use indirect addressing access the Upper 128 bytes of data RAM.

The stack pointer (SP) may be located anywhere in the 256 bytes

RAM (lower and upper RAM) internal data memory. The stack may

not be located in the ERAM.

AUXR

Address = 8EH

Reset Value = xxxx xx00B

Not Bit Addressable

—

6

—

5

—

4

—

3

—

2

EXTRAM

AO

Bit:

Function

Disable/Enable ALE

7

1

0

Symbol

AO

0

Operating Mode

1

ALE is emitted at a constant rate of / the oscillator frequency (6 clock mode; / f

in 12 clock mode).

3

6

OSC

1

ALE is active only during a MOVX or MOVC instruction.

EXTRAM

Internal/External RAM access using MOVX @Ri/@DPTR

EXTRAM

Operating Mode

0

1

Internal ERAM access using MOVX @Ri/@DPTR

External data memory access.

—

Not implemented, reserved for future use*.

NOTE:

*User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features. In that case, the reset or inactive value of the new

bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.

SU01258

Figure 27. AUXR: Auxiliary Register

30

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

FF

FFFF

UPPER

128 BYTES

INTERNAL RAM

SPECIAL

FUNCTION

REGISTER

EXTERNAL

DATA

MEMORY

80

ERAM

256 or 768 BYTES

LOWER

128 BYTES

INTERNAL RAM

100

00

0000

SU01293

Figure 28. Internal and External Data Memory Address Space with EXTRAM = 0

HARDWARE WATCHDOG TIMER (ONE-TIME ENABLED WITH RESET-OUT FOR 89C51RB2/RC2/RD2)

The WDT is intended as a recovery method in situations where the CPU may be subjected to software upset. The WDT consists of a 14-bit

counter and the WatchDog Timer reset (WDTRST) SFR. The WDT is disabled at reset. To enable the WDT, user must write 01EH and 0E1H in

sequence to the WDTRST, SFR location 0A6H. When WDT is enabled, it will increment every machine cycle while the oscillator is running and

there is no way to disable the WDT except through reset (either hardware reset or WDT overflow reset). When WDT overflows, it will drive an

output reset HIGH pulse at the RST-pin (see the note below).

Using the WDT

To enable the WDT, user must write 01EH and 0E1H in sequence to the WDTRST, SFR location 0A6H. When WDT is enabled, the user needs to

service it by writing to 01EH and 0E1H to WDTRST to avoid WDT overflow. The 14-bit counter overflows when it reaches 16383 (3FFFH) and this

will reset the device. When WDT is enabled, it will increment every machine cycle while the oscillator is running. This means the user must reset

the WDT at least every 16383 machine cycles. To reset the WDT, the user must write 01EH and 0E1H to WDTRST. WDTRST is a write only

register. The WDT counter cannot be read or written. When WDT overflows, it will generate an output RESET pulse at the reset pin (see note

below). The RESET pulse duration is 98 × T

(6 clock mode; 196 in 12 clock mode), where T

= 1/f . To make the best use of the WDT, it

OSC

should be serviced in those sections of code that will periodically be executed within the time required to prevent a WDT reset.

1, 2, 3

ABSOLUTE MAXIMUM RATINGS

PARAMETER

RATING

0 to +70 or –40 to +85

–65 to +150

0 to +13.0

–0.5 to +6.5

15

UNIT

°C

V

Operating temperature under bias

Storage temperature range

Voltage on EA/V pin to V

PP

SS

Voltage on any other pin to V

V

SS

Maximum I per I/O pin

mA

W

OL

Power dissipation (based on package heat transfer limitations, not device power consumption)

1.5

NOTES:

1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and

functional operation of the device at these or any conditions other than those described in the AC and DC Electrical Characteristics section

of this specification is not implied.

2. This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static

charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum.

3. Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to V unless otherwise noted.

SS

4. Programming is guaranteed from 0°C to T

for all devices.

max

31

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

DC ELECTRICAL CHARACTERISTICS

T

amb

= 0°C to +70°C or –40°C to +85°C; 5 V ±10%; V = 0 V

SS

LIMITS

TEST

CONDITIONS

SYMBOL

PARAMETER

UNIT

1

MIN

TYP

MAX

0.2V –0.1

V

Input low voltage

4.5 V < V < 5.5 V

–0.5

V

IL

CC

Input high voltage (ports 0, 1, 2, 3, EA)

Input high voltage, XTAL1, RST

0.2V +0.9

V

CC

V

CC

+0.5

IH

CC

0.7V

IH1

CC

V

OL

= 4.5 V

= 1.6 mA

CC

8

V

Output low voltage, ports 1, 2, 3

0.4

V

OL

2

I

V

CC

= 4.5 V

7, 8

Output low voltage, port 0, ALE, PSEN

0.4

OL1

OH

2

= 3.2 mA

OL

V

CC

= 4.5 V

= –30 µA

3

Output high voltage, ports 1, 2, 3

V

– 0.7

CC

I

OH

Output high voltage (port 0 in external bus mode),

V

CC

= 4.5 V

= –3.2 mA

V

OH1

CC

9

3

ALE , PSEN

I

OH

I

Logical 0 input current, ports 1, 2, 3

Logical 1-to-0 transition current, ports 1, 2, 3

Input leakage current, port 0

V

= 0.4 V

= 2.0 V

–1

–75

–650

±10

µA

IL

IN

6

TL

See Note 4

I

0.45 < V < V – 0.3

LI

IN

CC

Power supply current (see Figure 36):

Active mode (see Note 5)

See Note 5

CC

Idle mode (see Note 5)

Power-down mode or clock stopped (see

Figure 42 for conditions)

T

= 0°C to 70°C

= –40°C to +85°C

< 1

40

50

µA

amb

T

amb

R

C

Internal reset pull-down resistor

40

225

15

kΩ

RST

IO

10

Pin capacitance (except EA)

pF

NOTES:

1. Typical ratings are not guaranteed. The values listed are at room temperature, 5 V.

2. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the V s of ALE and ports 1 and 3. The noise is due

OL

to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the

worst cases (capacitive loading > 100 pF), the noise pulse on the ALE pin may exceed 0.8 V. In such cases, it may be desirable to qualify

ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input. I can exceed these conditions provided that no

OL

single output sinks more than 5 mA and no more than two outputs exceed the test conditions.

3. Capacitive loading on ports 0 and 2 may cause the V on ALE and PSEN to momentarily fall below the V –0.7 specification when the

OH

CC

address bits are stabilizing.

4. Pins of ports 1, 2 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its

maximum value when V is approximately 2 V.

IN

5. See Figures 39 through 42 for I test conditions and Figure 36 for I vs Freq.

CC

Active mode:

Idle mode:

6. This value applies to T

I

= (1.8 × FREQ. + 20)mA for all devices, in 6 clock mode; (0.9 × FREQ. + 20)mA in 12 clock mode.

= (0.7 × FREQ. +1.0)mA in 6 clock mode; (0.35 × FREQ. +1.0)mA in 12 clock mode.

= 0°C to +70°C.

CC(MAX)

amb

7. Load capacitance for port 0, ALE, and PSEN = 100 pF, load capacitance for all other outputs = 80 pF.

8. Under steady state (non-transient) conditions, I must be externally limited as follows:

OL

Maximum I per port pin:

15 mA (*NOTE: This is 85°C specification.)

OL

Maximum I per 8-bit port:

26 mA

71 mA

OL

Maximum total I for all outputs:

OL

If I exceeds the test condition, V may exceed the related specification. Pins are not guaranteed to sink current greater than the listed

OL

test conditions.

9. ALE is tested to V

, except when ALE is off then V is the voltage specification.

OH

OH1

10.Pin capacitance is characterized but not tested. Pin capacitance is less than 25 pF. Pin capacitance of ceramic package is less than 15 pF

(except EA is 25 pF).

11. Programming is guaranteed from 0°C to T

for all devices.

max

32

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

AC ELECTRICAL CHARACTERISTICS (6 CLOCK MODE)

1, 2, 3

T

amb

= 0°C to +70°C or –40°C to +85°C, V = 5 V ±10%, V = 0V

CC SS

4

VARIABLE CLOCK

20 MHz CLOCK

SYMBOL FIGURE

PARAMETER

MIN

MAX

MIN

0

MAX

UNIT

MHz

ns

1/t

CLCL

29

Oscillator frequency

ALE pulse width

0

20

t

–40

10

5

LHLL

CLCL

Address valid to ALE low

Address hold after ALE low

ALE low to valid instruction in

ALE low to PSEN low

0.5t

–20

ns

AVLL

LLAX

LLIV

CLCL

5

ns

CLCL

2t

–65

35

15

ns

CLCL

0.5t

1.5t

–20

–45

5

ns

LLPL

PLPH

PLIV

PXIX

PXIZ

AVIV

PLAZ

CLCL

PSEN pulse width

30

ns

CLCL

PSEN low to valid instruction in

Input instruction hold after PSEN

Input instruction float after PSEN

Address to valid instruction in

PSEN low to address float

1.5t

–60

ns

CLCL

0

ns

0.5t

2.5t

–20

–80

5

ns

CLCL

45

10

ns

CLCL

10

ns

Data Memory

t

30, 31

31

RD pulse width

3t

–100

50

ns

RLRH

WLWH

RLDV

RHDX

RHDZ

LLDV

CLCL

WR pulse width

CLCL

RD low to valid data in

Data hold after RD

Data float after RD

ALE low to valid data in

Address to valid data in

ALE low to RD or WR low

2.5t

–90

35

CLCL

0

t

–20

5

CLCL

4t

CLCL

–150

–165

50

4.5t

60

AVDV

LLWL

CLCL

1.5t

–50 1.5t

+50

25

0

125

CLCL

Address valid to WR low or RD low

Data valid to WR transition

Data hold after WR

2t

–75

AVWL

QVWX

WHQX

QVWH

RLAZ

WHLH

CLCL

0.5t

–25

–20

CLCL

5

CLCL

Data valid to WR high

3.5t

–130

CLCL

45

30, 31

RD low to address float

RD or WR high to ALE high

0

0.5t

–20 0.5t

+20

5

45

CLCL

External Clock

t

33

High time

Low time

Rise time

Fall time

20

t

–t

ns

CHCX

CLCX

CLCH

CHCL

CLCL CLCX

t

–t

CLCL CHCX

5

Shift Register

t

32

Serial port clock cycle time

6t

300

117

20

ns

XLXL

CLCL

Output data setup to clock rising edge

Output data hold after clock rising edge

Input data hold after clock rising edge

Clock rising edge to input data valid

5t

–133

CLCL

QVXH

XHQX

XHDX

XHDV

t

–30

CLCL

0

5t

CLCL

–133

117

NOTES:

1. Parameters are valid over operating temperature range unless otherwise specified.

2. Load capacitance for port 0, ALE, and PSEN = 100 pF, load capacitance for all other outputs = 80 pF.

3. Interfacing the microcontroller to devices with float times up to 45 ns is permitted. This limited bus contention will not cause damage to

Port 0 drivers.

4. Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz.

33

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

AC ELECTRICAL CHARACTERISTICS (12 CLOCK MODE)

1, 2, 3

T

amb

= 0°C to +70°C or –40°C to +85°C, V = 5 V ±10%, V = 0 V

CC SS

4

VARIABLE CLOCK

33 MHz CLOCK

SYMBOL FIGURE

PARAMETER

MIN

MAX

MIN

0

MAX

UNIT

MHz

ns

1/t

CLCL

29

Oscillator frequency

ALE pulse width

0

33

t

2t

–40

21

5

LHLL

CLCL

Address valid to ALE low

Address hold after ALE low

ALE low to valid instruction in

ALE low to PSEN low

t

–25

ns

AVLL

LLAX

LLIV

CLCL

–25

5

ns

4t

3t

–65

–60

55

30

ns

CLCL

t

–25

5

ns

LLPL

PLPH

PLIV

PXIX

PXIZ

AVIV

PLAZ

CLCL

PSEN pulse width

3t

–45

45

ns

CLCL

PSEN low to valid instruction in

Input instruction hold after PSEN

Input instruction float after PSEN

Address to valid instruction in

PSEN low to address float

ns

CLCL

0

ns

t

–25

5

ns

CLCL

5t

–80

70

10

ns

CLCL

10

ns

Data Memory

t

30, 31

31

RD pulse width

6t

–100

82

ns

RLRH

WLWH

RLDV

RHDX

RHDZ

LLDV

CLCL

WR pulse width

6t

CLCL

RD low to valid data in

Data hold after RD

Data float after RD

ALE low to valid data in

Address to valid data in

ALE low to RD or WR low

5t

2t

–90

–28

60

CLCL

0

32

90

CLCL

8t

–150

–165

CLCL

9t

105

140

AVDV

LLWL

3t

–50

–75

3t

CLCL

+50

40

45

0

CLCL

Address valid to WR low or RD low

Data valid to WR transition

Data hold after WR

4t

AVWL

QVWX

WHQX

QVWH

RLAZ

WHLH

CLCL

t

–30

–25

CLCL

5

Data valid to WR high

7t

–130

80

CLCL

30, 31

RD low to address float

RD or WR high to ALE high

0

t

–25

t

+25

5

55

CLCL

External Clock

t

33

High time

Low time

Rise time

Fall time

17

t

–t

ns

CHCX

CLCX

CLCH

CHCL

CLCL CLCX

t

–t

CLCL CHCX

5

Shift Register

t

32

Serial port clock cycle time

12t

360

167

50

ns

XLXL

CLCL

Output data setup to clock rising edge

Output data hold after clock rising edge

Input data hold after clock rising edge

Clock rising edge to input data valid

10t –133

CLCL

QVXH

XHQX

XHDX

XHDV

2t

CLCL

–80

0

10t

–133

167

CLCL

NOTES:

1. Parameters are valid over operating temperature range unless otherwise specified.

2. Load capacitance for port 0, ALE, and PSEN = 100 pF, load capacitance for all other outputs = 80 pF.

3. Interfacing the microcontroller to devices with float times up to 45 ns is permitted. This limited bus contention will not cause damage to

Port 0 drivers.

4. Parts are tested to 3.5 MHz, but guaranteed to operate down to 0 Hz.

34

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

EXPLANATION OF THE AC SYMBOLS

Each timing symbol has five characters. The first character is always

P – PSEN

‘t’ (= time). The other characters, depending on their positions,

indicate the name of a signal or the logical status of that signal. The

designations are:

Q – Output data

R – RD signal

t – Time

A – Address

V – Valid

C – Clock

W– WR signal

D – Input data

X – No longer a valid logic level

Z – Float

H – Logic level high

I – Instruction (program memory contents)

L – Logic level low, or ALE

Examples: t

= Time for address valid to ALE low.

= Time for ALE low to PSEN low.

AVLL

LLPL

t

LHLL

ALE

t

LLPL

AVLL

t

PLPH

t

LLIV

t

PLIV

PSEN

t

LLAX

t

PXIZ

t

PLAZ

t

PXIX

A0–A7

INSTR IN

A0–A7

PORT 0

PORT 2

t

AVIV

A0–A15

A8–A15

SU00006

Figure 29. External Program Memory Read Cycle

ALE

PSEN

RD

t

WHLH

t

LLDV

t

LLWL

RLRH

t

RHDZ

t

LLAX

t

RLDV

AVLL

t

RLAZ

t

RHDX

A0–A7

FROM RI OR DPL

PORT 0

PORT 2

DATA IN

A0–A7 FROM PCL

INSTR IN

t

AVWL

t

AVDV

P2.0–P2.7 OR A8–A15 FROM DPF

A0–A15 FROM PCH

SU00025

Figure 30. External Data Memory Read Cycle

35

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

ALE

t

WHLH

PSEN

t

WLWH

LLWL

WR

t

LLAX

t

WHQX

t

AVLL

QVWX

t

QVWH

A0–A7

FROM RI OR DPL

PORT 0

PORT 2

DATA OUT

A0–A7 FROM PCL

INSTR IN

t

AVWL

P2.0–P2.7 OR A8–A15 FROM DPF

A0–A15 FROM PCH

SU00026

Figure 31. External Data Memory Write Cycle

INSTRUCTION

ALE

0

1

2

3

4

5

6

7

8

t

XLXL

CLOCK

t

XHQX

t

QVXH

OUTPUT DATA

0

1

2

3

4

5

6

7

WRITE TO SBUF

t

XHDX

t

SET TI

VALID

XHDV

INPUT DATA

CLEAR RI

VALID

SET RI

SU00027

Figure 32. Shift Register Mode Timing

V

–0.5

CC

0.7V

CC

0.45V

0.2V

–0.1

t

CHCX

t

CHCL

CLCX

CLCH

t

CLCL

SU00009

Figure 33. External Clock Drive

36

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

V

–0.5

CC

V

+0.1V

LOAD

V

–0.1V

TIMING

REFERENCE

POINTS

OH

0.2V

+0.9

–0.1

CC

V

LOAD

CC

–0.1V

LOAD

+0.1V

OL

0.45V

NOTE:

For timing purposes, a port is no longer floating when a 100mV change from

load voltage occurs, and begins to float when a 100mV change from the loaded

AC inputs during testing are driven at V –0.5 for a logic ‘1’ and 0.45V for a logic ‘0’.

Timing measurements are made at V min for a logic ‘1’ and V max for a logic ‘0’.

CC

IH

IL

V

/V level occurs. I /I ≥ ±20mA.

OH OL

SU00717

SU00718

Figure 34. AC Testing Input/Output

Figure 35. Float Waveform

60

50

I

(mA)

CC

40

89C51RB2/RC2/RD2

MAXIMUM ACTIVE I

CC

30

20

TYPICAL ACTIVE I

CC

10

MAXIMUM IDLE

TYPICAL IDLE

2

4

6

8

10

12

14

16

18

Frequency at XTAL1 (MHz, 6 clock mode)

SU01300

Figure 36. I vs. FREQ

CC

Valid only within frequency specifications of the device under test

V

–0.5

CC

0.2V

+0.9

–0.1

CC

0.45V

NOTE:

AC inputs during testing are driven at V –0.5 for a logic ‘1’ and 0.45V for a logic ‘0’.

CC

Timing measurements are made at V min for a logic ‘1’ and V max for a logic ‘0’.

IH

IL

SU00010

Figure 37. AC Testing Input/Output

37

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

V

+0.1V

LOAD

V

–0.1V

TIMING

REFERENCE

POINTS

OH

V

LOAD

–0.1V

LOAD

+0.1V

OL

NOTE:

For timing purposes, a port is no longer floating when a 100mV change from load voltage occurs,

and begins to float when a 100mV change from the loaded V /V level occurs. I /I ≥ ±20mA.

OH OL

SU00011

Figure 38. Float Waveform

V

–0.5

CC

0.5V

I

CC

t

CHCX

t

CHCL

CLCX

CLCH

V

CC

P0

V

CC

t

CLCL

89C51RB2

89C51RC2

89C51RD2

RST

SU01297

EA

Figure 41. Clock Signal Waveform for I Tests in Active

(NC)

XTAL2

XTAL1

CC

and Idle Modes.

CLOCK SIGNAL

t

= t

= 10 ns

CHCL

CLCL

V

SS

V

CC

SU01294

I

CC

Figure 39. I Test Condition, Active Mode.

CC

V

CC

All other pins are disconnected

RST

EA

V

P0

89C51RB2

89C51RC2

89C51RD2

V

CC

I

CC

(NC)

XTAL2

XTAL1

V

CC

P0

RST

EA

V

CC

V

SS

89C51RB2

89C51RC2

89C51RD2

SU01296

(NC)

XTAL2

XTAL1

Figure 42. I Test Condition, Power Down Mode.

CC

CLOCK SIGNAL

All other pins are disconnected; V = 2V to 5.5V

CC

V

SS

SU01295

Figure 40. I Test Condition, Idle Mode.

CC

All other pins are disconnected

38

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

FLASH EPROM MEMORY

CAPABILITIES OF THE PHILIPS 89C51

FLASH-BASED MICROCONTROLLERS

GENERAL DESCRIPTION

Flash organization

The 89C51RB2/RC2/RD2 Flash memory augments EPROM

functionality with in-circuit electrical erasure and programming. The

Flash can be read and written as bytes. The Chip Erase operation will

erase the entire program memory. The Block Erase function can

erase any Flash block. In-system programming and standard parallel

programming are both available. On-chip erase and write timing

generation contribute to a user friendly programming interface.

The 89C51RB2/RC2/RD2 contains 16KB/32KB/64Kbytes of Flash

program memory. This memory is organized as 5 separate blocks.

The first two blocks are 8 kB in size, filling the program memory

space from address 0 through 3FFF hex. The final three blocks are

16 kB in size and occupy addresses from 4000 through FFFF hex.

Figure 43 depicts the Flash memory configurations.

The 89C51RB2/RC2/RD2 Flash reliably stores memory contents

even after 1000 erase and program cycles. The cell is designed to

optimize the erase and programming mechanisms. In addition, the

combination of advanced tunnel oxide processing and low internal

electric fields for erase and programming operations produces

Flash Programming and Erasure

There are three methods of erasing or programming of the Flash

memory that may be used. First, the Flash may be programmed or

erased in the end-user application by calling low-level routines

through a common entry point in the Boot ROM. The end-user

application, though, must be executing code from a different block

than the block that is being erased or programmed. Second, the

on-chip ISP boot loader may be invoked. This ISP boot loader will, in

turn, call low-level routines through the same common entry point in

the Boot ROM that can be used by the end-user application. Third,

the Flash may be programmed or erased using the parallel method

by using a commercially available EPROM programmer. The parallel

programming method used by these devices is similar to that used

by EPROM 87C51, but it is not identical, and the commercially

available programmer will need to have support for these devices.

reliable cycling. The 89C51RB2/RC2/RD2 uses a +5 V V supply

PP

to perform the Program/Erase algorithms.

FEATURES

• Flash EPROM internal program memory with Block Erase.

• Internal 1 kB fixed boot ROM, containing low-level in-system

programming routines and a default serial loader. User program

can call these routines to perform In-Application Programming

(IAP). The Boot ROM can be turned off to provide access to the

full 64 kB Flash memory.

Boot ROM

When the microcontroller programs its own Flash memory, all of the

low level details are handled by code that is permanently contained

in a 1 kB Boot ROM that is separate from the Flash memory. A user

program simply calls the common entry point with appropriate

parameters in the Boot ROM to accomplish the desired operation.

Boot ROM operations include things like: erase block, program byte,

verify byte, program security lock bit, etc. The Boot ROM overlays

the program memory space at the top of the address space from

FC00 to FFFF hex, when it is enabled. The Boot ROM may be

turned off so that the upper 1 kB of Flash program memory are

accessible for execution.

• Boot vector allows user provided Flash loader code to reside

anywhere in the Flash memory space. This configuration provides

flexibility to the user.

• Default loader in Boot ROM allows programming via the serial port

without the need for a user provided loader.

• Up to 64 kB external program memory if the internal program

memory is disabled (EA = 0).

• Programming and erase voltage +5 V or +12 V.

• Read/Programming/Erase:

– Byte-wise read (100 ns access time).

– Byte Programming (20 ms).

– Typical erase times:

Block Erase (8 kB or 16 kB) in 3 seconds.

Full Erase (64 kB) in 3 seconds.

• Parallel programming with 87C51 compatible hardware interface

to programmer.

• In-system programming.

• Programmable security for the code in the Flash.

• 1000 minimum erase/program cycles for each byte.

• 10-year minimum data retention.

39

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

FFFF

BOOT ROM

(1 kB)

FC00

BLOCK 4

16 kB

89C51RD2

C000

BLOCK 3

16 kB

PROGRAM

ADDRESS

8000

BLOCK 2

16 kB

89C51RC2

4000

BLOCK 1

8 kB

2000

89C51RB2

BLOCK 0

8 kB

0000

SU01298

Figure 43. Flash Memory Configurations

Power-On Reset Code Execution

Hardware Activation of the Boot Loader

The 89C51RB2/RC2/RD2 contains two special Flash registers: the

BOOT VECTOR and the STATUS BYTE. At the falling edge of reset,

the 89C51RB2/RC2/RD2 examines the contents of the Status Byte.

If the Status Byte is set to zero, power-up execution starts at

location 0000H, which is the normal start address of the user’s

application code. When the Status Byte is set to a value other than

zero, the contents of the Boot Vector is used as the high byte of the

execution address and the low byte is set to 00H. The factory

default setting is 0FCH, corresponds to the address 0FC00H for the

factory masked-ROM ISP boot loader. A custom boot loader can be

written with the Boot Vector set to the custom boot loader.

The boot loader can also be executed by holding PSEN LOW,

EA greater than V (such as +5 V), and ALE HIGH (or not connected)

IH

at the falling edge of RESET. This is the same effect as having a

non-zero status byte. This allows an application to be built that will

normally execute the end user’s code but can be manually forced

into ISP operation.

If the factory default setting for the Boot Vector (0FCH) is changed, it

will no longer point to the ISP masked-ROM boot loader code. If this

happens, the only way it is possible to change the contents of the

Boot Vector is through the parallel programming method, provided

that the end user application does not contain a customized loader

that provides for erasing and reprogramming of the Boot Vector and

Status Byte.

NOTE: When erasing the Status Byte or Boot Vector,

both bytes are erased at the same time. It is necessary

to reprogram the Boot Vector after erasing and

updating the Status Byte.

After programming the Flash, the status byte should be programmed

to zero in order to allow execution of the user’s application code

beginning at address 0000H.

40

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

V

CC

V

+12 V OR + 5 V

PP

RST

V

+5 V

TxD

RxD

CC

TxD

RxD

XTAL2

V

89C51RB2

89C51RC2

89C51RD2

SS

XTAL1

V

SS

SU01299

Figure 44. In-System Programming with a Minimum of Pins

first byte in the record. If there are zero bytes in the record, this field

In-System Programming (ISP)

is often set to 0000. The “RR” string indicates the record type. A

record type of “00” is a data record. A record type of “01” indicates

the end-of-file mark. In this application, additional record types will

be added to indicate either commands or data for the ISP facility.

The maximum number of data bytes in a record is limited to 16

(decimal). ISP commands are summarized in Table 8.

The In-System Programming (ISP) is performed without removing

the microcontroller from the system. The In-System Programming

(ISP) facility consists of a series of internal hardware resources

coupled with internal firmware to facilitate remote programming of

the 89C51RB2/RC2/RD2 through the serial port. This firmware is

provided by Philips and embedded within each

89C51RB2/RC2/RD2 device.

As a record is received by the 89C51RB2/RC2/RD2, the information

in the record is stored internally and a checksum calculation is

performed. The operation indicated by the record type is not

performed until the entire record has been received. Should an error

occur in the checksum, the 89C51RB2/RC2/RD2 will send an “X”

out the serial port indicating a checksum error. If the checksum

calculation is found to match the checksum in the record, then the

command will be executed. In most cases, successful reception of

the record will be indicated by transmitting a “.” character out the

serial port (displaying the contents of the internal program memory

is an exception).

The Philips In-System Programming (ISP) facility has made in-circuit

programming in an embedded application possible with a minimum

of additional expense in components and circuit board area.

The ISP function uses five pins: TxD, RxD, V , V , and V (see

Figure 44). Only a small connector needs to be available to interface

your application to an external circuit in order to use this feature.

SS

CC

PP

The V supply should be adequately decoupled and V not

PP

allowed to exceed datasheet limits.

Using the In-System Programming (ISP)

In the case of a Data Record (record type 00), an additional check is

made. A “.” character will NOT be sent unless the record checksum

matched the calculated checksum and all of the bytes in the record

were successfully programmed. For a data record, an “X” indicates

that the checksum failed to match, and an “R” character indicates

that one of the bytes did not properly program. It is necessary to

send a type 02 record (specify oscillator frequency) to the

89C51RB2/RC2/RD2 before programming data.

The ISP feature allows for a wide range of baud rates to be used in

your application, independent of the oscillator frequency. It is also

adaptable to a wide range of oscillator frequencies. This is

accomplished by measuring the bit-time of a single bit in a received

character. This information is then used to program the baud rate in

terms of timer counts based on the oscillator frequency. The ISP

feature requires that an initial character (an uppercase U) be sent to

the 89C51RB2/RC2/RD2 to establish the baud rate. The ISP

firmware provides auto-echo of received characters.

The ISP facility was designed to that specific crystal frequencies

were not required in order to generate baud rates or time the

programming pulses. The user thus needs to provide the

89C51RB2/RC2/RD2 with information required to generate the

proper timing. Record type 02 is provided for this purpose.

Once baud rate initialization has been performed, the ISP firmware

will only accept Intel Hex-type records. Intel Hex records consist of

ASCII characters used to represent hexadecimal values and are

summarized below:

WinISP, a software utility to implement ISP programming with a PC,

is available from Philips. Commercial serial ISP programmers are

available from third parties. Please check the Philips web site

(www.semiconductors.philips.com) for additional information.

:NNAAAARRDD..DDCC<crlf>

In the Intel Hex record, the “NN” represents the number of data

bytes in the record. The 89C51RB2/RC2/RD2 will accept up to 16

(10H) data bytes. The “AAAA” string represents the address of the

41

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

Table 8. Intel-Hex Records Used by In-System Programming

RECORD TYPE

COMMAND/DATA FUNCTION

00

Program Data

:nnaaaa00dd....ddcc

Where:

Nn

Aaaa

= number of bytes (hex) in record

= memory address of first byte in record

dd....dd = data bytes

cc

= checksum

Example:

:10008000AF5F67F0602703E0322CFA92007780C3FD

01

02

End of File (EOF), no operation

:xxxxxx01cc

Where:

xxxxxx

cc

= required field, but value is a “don’t care”

= checksum

Example:

:00000001FF

Specify Oscillator Frequency

:01xxxx02ddcc

Where:

xxxx

dd

cc

= required field, but value is a “don’t care”

= integer oscillator frequency rounded down to nearest MHz

= checksum

Example:

:0100000210ED

(dd = 10h = 16, used for 16.0–16.9 MHz)

42

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

RECORD TYPE

COMMAND/DATA FUNCTION

03

Miscellaneous Write Functions

:nnxxxx03ffssddcc

Where:

nn

xxxx

03

= number of bytes (hex) in record

= required field, but value is a “don’t care”

= Write Function

ff

ss

= subfunction code

= selection code

dd

cc

= data input (as needed)

= checksum

Subfunction Code = 01 (Erase Blocks)

ff = 01

ss = block code as shown below:

block 0, 0k to 8k, 00H

block 1, 8k to 16k, 20H

block 2, 16k to 32k, 40H

block 3, 32k to 48k, 80H

block 4, 48k to 64k, C0H

Example:

:0200000301C03A erase block 4

Subfunction Code = 04 (Erase Boot Vector and Status Byte)

ff = 04

ss = don’t care

dd = don’t care

Example:

:020000030400F7 erase boot vector and status byte

Subfunction Code = 05 (Program Security Bits)

ff = 05

ss = 00 program security bit 1 (inhibit writing to Flash)

01 program security bit 2 (inhibit Flash verify)

02 program security bit 3 (disable eternal memory)

Example:

:020000030501F5 program security bit 2

Subfunction Code = 06 (Program Status Byte or Boot Vector)

ff = 06

ss = 00 program status byte

01 program boot vector

Example:

:030000030601FCF7 program boot vector with 0FCH

Subfunction Code = 07 (Full Chip Erase)

Erases all blocks, security bits, and sets status and boot vector to default values

ff = 07

ss = don’t care

dd = don’t care

Example:

:0100000307F5 full chip erase

04

Display Device Data or Blank Check – Record type 04 causes the contents of the entire Flash array to be sent out

the serial port in a formatted display. This display consists of an address and the contents of 16 bytes starting with that

address. No display of the device contents will occur if security bit 2 has been programmed. The dumping of the device

data to the serial port is terminated by the reception of any character.

General Format of Function 04

:05xxxx04sssseeeeffcc

Where:

05

xxxx

04

ssss

eeee

ff

= number of bytes (hex) in record

= required field, but value is a “don’t care”

= “Display Device Data or Blank Check” function code

= starting address

= ending address

= subfunction

00 = display data

01 = blank check

= checksum

cc

Example:

:0500000440004FFF0069 display 4000–4FFF

43

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

RECORD TYPE

COMMAND/DATA FUNCTION

05

Miscellaneous Read Functions

General Format of Function 05

:02xxxx05ffsscc

Where:

02

xxxx

05

=

number of bytes (hex) in record

required field, but value is a “don’t care”

“Miscellaneous Read” function code

ffss

subfunction and selection code

0000 = read signature byte – manufacturer id (15H)

0001 = read signature byte – device id # 1

0002 = read signature byte – device id # 2

(C2H)

0700 = read security bits

0701 = read status byte

0702 = read boot vector

cc

= checksum

Example:

:020000050001F8 read signature byte – device id # 1

06

Direct Load of Baud Rate

General Format of Function 06

:02xxxx06hhllcc

Where:

02

xxxx

06

hh

ll

=

number of bytes (hex) in record

required field, but value is a “don’t care”

”Direct Load of Baud Rate” function code

high byte of Timer 2

low byte of Timer 2

checksum

cc

Example:

:02000006F50003

44

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

the microcontroller’s registers before making a call to PGM_MTP at

FFF0H. The oscillator frequency is an integer number rounded down

to the nearest megahertz. For example, set R0 to 11 for 11.0592 MHz.

Results are returned in the registers. The API calls are shown in

Table 9.

In Application Programming Method

Several In Application Programming (IAP) calls are available for use by

an application program to permit selective erasing and programming of

Flash sectors. All calls are made through a common interface,

PGM_MTP. The programming functions are selected by setting up

Table 9. IAP calls

IAP CALL

PARAMETER

PROGRAM DATA BYTE

Input Parameters:

R0 = osc freq (integer)

R1 = 02h

DPTR = address of byte to program

ACC = byte to program

Return Parameter

ACC = 00 if pass, !00 if fail

ERASE BLOCK

Input Parameters:

R0 = osc freq (integer)

R1 = 01h

DPH = block code as shown below:

block 0, 0k to 8k, 00H

block 1, 8k to 16k, 20H

block 2, 16k to 32k, 40H

block 3, 32k to 48k, 80H

block 4, 48k to 64k, C0H

DPL = 00h

Return Parameter

none

ERASE BOOT VECTOR

Input Parameters:

R0 = osc freq (integer)

R1 = 04h

DPH = 00h

DPL = don’t care

Return Parameter

none

PROGRAM SECURITY BIT

Input Parameters:

R0 = osc freq (integer)

R1 = 05h

DPH = 00h

DPL = 00h – security bit # 1 (inhibit writing to Flash)

01h – security bit # 2 (inhibit Flash verify)

02h – security bit # 3 (disable external memory)

Return Parameter

none

PROGRAM STATUS BYTE

Input Parameters:

R0 = osc freq (integer)

R1 = 06h

DPH = 00h

DPL = 00h – program status byte

ACC = status byte

Return Parameter

ACC = status byte

PROGRAM BOOT VECTOR

Input Parameters:

R0 = osc freq (interger)

R1 = 06h

DPH = 00h

DPL = 01h – program boot vector

ACC = boot vector

Return Parameter

ACC = boot vector

READ DEVICE DATA

Input Parameters:

R1 = 03h

DPTR = address of byte to read

Return Parameter

ACC = value of byte read

45

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

IAP CALL

PARAMETER

READ MANUFACTURER ID

Input Parameters:

R0 = osc freq (integer)

R1 = 00h

DPH = 00h

DPL = 00h (manufacturer ID)

Return Parameter

ACC = value of byte read

READ DEVICE ID # 1

READ DEVICE ID # 2

READ SECURITY BITS

READ STATUS BYTE

READ BOOT VECTOR

FULL CHIP ERASE

Input Parameters:

R0 = osc freq (integer)

R1 = 00h

DPH = 00h

DPL = 01h (device ID # 1)

Return Parameter

ACC = value of byte read

Input Parameters:

R0 = osc freq (integer)

R1 = 00h

DPH = 00h

DPL = 02h (device ID # 2)

Return Parameter

ACC = value of byte read

Input Parameters:

R0 = osc freq (integer)

R1 = 07h

DPH = 00h

DPL = 00h (security bits)

Return Parameter

ACC = value of byte read

Input Parameters:

R0 = osc freq (integer)

R1 = 07h

DPH = 00h

DPL = 01h (status byte)

Return Parameter

ACC = value of byte read

Input Parameters:

R0 = osc freq (integer)

R1 = 07h

DPH = 00h

DPL = 02h (boot vector)

Return Parameter

ACC = value of byte read

Input Parameters:

R0 = osc frequency

R1 = 08h

DPH = don’t care

DPL = don’t care

Return Parameter

none

46

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

Security

The security feature protects against software piracy and prevents

the contents of the Flash from being read. The Security Lock bits

are located in Flash. The 89C51RB2/RC2/RD2 has 3 programmable

security lock bits that will provide different levels of protection for the

on-chip code and data (see Table 10).

Table 10.

1

SECURITY LOCK BITS

PROTECTION DESCRIPTION

LB1

LB2

LB3

X

MOVC instructions executed from external program memory are disabled from fetching code bytes

from internal memory.

1

X

1

X

1

Block erase is disabled. Erase or programming of the status byte or boot vector is disabled.

Verify of code memory is disabled.

X

External execution is disabled.

NOTE:

1. Security bits are independent of each other. Full-chip erase may be performed regardless of the state of the security bits.

47

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

DIP40: plastic dual in-line package; 40 leads (600 mil)

SOT129-1

48

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

PLCC44: plastic leaded chip carrier; 44 leads

SOT187-2

49

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

QFP44: plastic quad flat package; 44 leads (lead length 1.3 mm); body 10 x 10 x 1.75 mm

SOT307-2

50

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

NOTES

51

1999 Sep 23

Philips Semiconductors

Preliminary specification

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM

89C51RB2/89C51RC2/

89C51RD2

Data sheet status

[1]

Data sheet

status

Product

status

Definition

Objective

specification

Development

This data sheet contains the design target or goal specifications for product development.

Specification may change in any manner without notice.

Preliminary

specification

Qualification

This data sheet contains preliminary data, and supplementary data will be published at a later date.

Philips Semiconductors reserves the right to make changes at any time without notice in order to

improve design and supply the best possible product.

Product

specification

Production

This data sheet contains final specifications. Philips Semiconductors reserves the right to make

changes at any time without notice in order to improve design and supply the best possible product.

[1] Please consult the most recently issued datasheet before initiating or completing a design.

Definitions

Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For

detailed information see the relevant data sheet or data handbook.

Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one

or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or

at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended

periods may affect device reliability.

Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips

Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or

modification.

Disclaimers

Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can

reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications

do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.

Righttomakechanges—PhilipsSemiconductorsreservestherighttomakechanges, withoutnotice, intheproducts, includingcircuits,standard

cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no

responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these

products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless

otherwise specified.

Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409

Copyright Philips Electronics North America Corporation 1999

Sunnyvale, California 94088–3409

Telephone 800-234-7381

Date of release: 09-99

Document order number:

9397–750–06427

Philips

Semiconductors

52

1999 Sep 23


型号：	P89C51RD2HBA
厂家：	NXP
描述：	80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM 80C51的8位闪存微控制器系列16KB / 32KB / 64KB ISP / IAP闪存与512B / 512B / 1KB RAM 闪存微控制器
文件：	总52页 (文件大小：292K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

P89C51RD2HBA [NXP]

相关型号：

P89C51RD2HBA/00

P89C51RD2HBB

P89C51RD2HBBD

P89C51RD2HBP

P89C51RD2HBP/00

P89C51RD2HFA

P89C51RD2HFB

P89C51RD2HFP

P89C51RD2HXX

P89C51UBAA

P89C51UBAA-T

P89C51UBBB