BTA208S-800F [NXP]
Three quadrant triacs guaranteed commutation; 三象限三端双向可控硅保证换向型号: | BTA208S-800F |
厂家: | NXP |
描述: | Three quadrant triacs guaranteed commutation |
文件: | 总4页 (文件大小:25K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Philips Semiconductors
Objective specification
Three quadrant triacs
guaranteed commutation
BTA208S series D, E and F
GENERAL DESCRIPTION
QUICK REFERENCE DATA
Passivated guaranteed commutation
triacs in a plastic envelope suitable for
surface mounting, intended for use in
motor control circuits or with other highly
inductive loads. These devices balance
the requirements of commutation
performance and gate sensitivity. The
"sensitive gate" E series and "logic level"
D series are intended for interfacing with
low power drivers, including micro
controllers.
SYMBOL
PARAMETER
MAX. MAX. UNIT
BTA208S-
BTA208S-
BTA208S-
600D
-
600E 800E
600F 800F
VDRM
Repetitive peak off-state
voltages
RMS on-state current
Non-repetitive peak on-state
current
600
800
V
IT(RMS)
ITSM
8
65
8
65
A
A
PINNING - SOT428
PIN CONFIGURATION
SYMBOL
PIN
NUMBER
Standard
S
tab
1
2
MT1
MT2
gate
MT2
T2
T1
2
3
G
1
3
tab
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum System (IEC 134).
SYMBOL PARAMETER
CONDITIONS
MIN.
MAX.
UNIT
V
-600
6001
-800
800
VDRM
Repetitive peak off-state
voltages
-
-
IT(RMS)
ITSM
RMS on-state current
full sine wave;
8
A
Tmb ≤ 102 ˚C
Non-repetitive peak
on-state current
full sine wave;
Tj = 25 ˚C prior to
surge
t = 20 ms
-
-
-
65
72
A
A
t = 16.7 ms
I2t
I2t for fusing
Repetitive rate of rise of
on-state current after
triggering
Peak gate current
Peak gate voltage
Peak gate power
Average gate power
t = 10 ms
21
A2s
A/µs
dIT/dt
ITM = 12 A; IG = 0.2 A;
dIG/dt = 0.2 A/µs
100
IGM
-
-
-
-
2
5
5
A
V
W
W
VGM
PGM
PG(AV)
over any 20 ms
period
0.5
Tstg
Tj
Storage temperature
Operating junction
temperature
-40
-
150
125
˚C
˚C
1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may
switch to the on-state. The rate of rise of current should not exceed 6 A/µs.
October 1999
1
Rev 1.200
Philips Semiconductors
Objective specification
Three quadrant triacs
guaranteed commutation
BTA208S series D, E and F
THERMAL RESISTANCES
SYMBOL PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
Rth j-mb
Thermal resistance
full cycle
-
-
-
-
-
75
2.0
2.4
-
K/W
K/W
K/W
junction to mounting base half cycle
Rth j-a
Thermal resistance
junction to ambient
pcb (FR4) mounted; footprint as in Fig.14
STATIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOL PARAMETER
CONDITIONS
BTA208S-
MIN. TYP.
MAX.
...E
UNIT
...D
...F
IGT
Gate trigger current2
Latching current
VD = 12 V; IT = 0.1 A
T2+ G+
-
-
-
-
-
-
5
5
5
10
10
10
25
25
25
mA
mA
mA
T2+ G-
T2- G-
IL
VD = 12 V; IGT = 0.1 A
T2+ G+
T2+ G-
T2- G-
-
-
-
-
-
-
15
25
25
20
30
30
25
40
40
mA
mA
mA
IH
Holding current
VD = 12 V; IGT = 0.1 A
-
-
15
25
30
mA
VT
On-state voltage
IT = 10 A
-
-
1.3
0.7
0.4
1.65
1.5
-
V
V
V
VGT
Gate trigger voltage
VD = 12 V; IT = 0.1 A
VD = 400 V; IT = 0.1 A;
Tj = 125 ˚C
0.25
ID
Off-state leakage current VD = VDRM(max)
;
-
0.1
0.5
mA
Tj = 125 ˚C
DYNAMIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOL PARAMETER
CONDITIONS
MIN.
...E
60
TYP. MAX. UNIT
BTA208S- ...D
...F
dVD/dt
Critical rate of rise of
off-state voltage
VDM = 67% VDRM(max)
;
30
70
-
-
V/µs
Tj = 110 ˚C; exponential
waveform; gate open
circuit
dIcom/dt
Critical rate of change of
commutating current
VDM = 400 V; Tj = 110 ˚C; 1.8
IT(RMS) = 8 A;
dVcom/dt = 20v/µs; gate
open circuit
3.5
4.5
-
4.5
5.5
-
A/ms
dIcom/dt
Critical rate of change of
commutating current
VDM = 400 V; Tj = 110 ˚C; 3.5
IT(RMS) = 8 A;
dVcom/dt = 0.1v/µs; gate
open circuit
-
-
A/ms
tgt
Gate controlled turn-on
time
ITM = 12 A; VD = VDRM(max)
IG = 0.1 A; dIG/dt = 5 A/µs
;
-
2
µs
2 Device does not trigger in the T2-, G+ quadrant.
October 1999
2
Rev 1.200
Philips Semiconductors
Objective specification
Three quadrant triacs
guaranteed commutation
BTA208S series D, E and F
MECHANICAL DATA
Dimensions in mm
Net Mass: 1.1 g
seating plane
2.38 max
0.93 max
1.1
5.4
6.73 max
tab
4 min
4.6
6.22 max
0.5 min
10.4 max
0.5
2
0.3
0.5
3
1
0.8 max
(x2)
2.285 (x2)
Fig.1. SOT428 : centre pin connected to tab.
MOUNTING INSTRUCTIONS
Dimensions in mm
7.0
7.0
2.15
2.5
1.5
4.57
Fig.2. SOT428 : minimum pad sizes for surface mounting.
Notes
1. Plastic meets UL94 V0 at 1/8".
October 1999
3
Rev 1.200
Philips Semiconductors
Objective specification
Three quadrant triacs
guaranteed commutation
BTA208S series D, E and F
DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and
operation of the device at these or at any other conditions above those given in the Characteristics sections of
this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
Philips Electronics N.V. 1999
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the
copyright owner.
The information presented in this document does not form part of any quotation or contract, it is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under patent or other
industrial or intellectual property rights.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices or systems where malfunction of these
products can be reasonably expected to result in personal injury. Philips customers using or selling these products
for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting
from such improper use or sale.
October 1999
4
Rev 1.200
相关型号:
©2020 ICPDF网 联系我们和版权申明