M25P16-VMN6T [NUMONYX]
16 Mbit, serial Flash memory, 75 MHz SPI bus interface; 16兆位串行闪存， 75 MHz的SPI总线接口
| 型号： | M25P16-VMN6T |
| 厂家： | 
NUMONYX B.V |
| 描述： | 16 Mbit, serial Flash memory, 75 MHz SPI bus interface |
| 文件： | 总55页 (文件大小：1057K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
M25P16
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Features
■ 16 Mbit of Flash memory
■ Page Program (up to 256 bytes) in 0.64 ms
VFQFPN8 (MP)
6 × 5 mm (MLP8)
(typical)
■ Sector Erase (512 Kbit) in 0.6 s (typical)
■ Bulk Erase (16 Mbit) in 13 s (typical)
■ 2.7 V to 3.6 V single supply voltage
■ SPI bus compatible serial interface
■ 75 MHz Clock rate (maximum)
■ Deep Power-down mode 1 µA (typical)
■ Electronic signatures
VDFPN8 (ME)
8 x 6 mm (MLP8)
– JEDEC standard two-byte signature
(2015h)
– Unique ID code (UID) with 16 bytes read-
only, available upon customer request
– RES instruction, one-byte, signature (14h),
for backward compatibility
SO8N (MN)
150 mils width
■ More than 100,000 Erase/Program cycles per
sector
■ Hardware Write Protection: protected area size
defined by three non-volatile bits (BP0, BP1
and BP2)
SO8W (MW)
208 mils width
■ More than 20 year data retention
■ Packages
– ECOPACK® (RoHS compliant)
SO16 (MF)
300 mils width
December 2007
Rev 13
1/55
www.numonyx.com
1
Contents
M25P16
Contents
1
2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
Serial Data output (Q) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Serial Data input (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Serial Clock (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chip Select (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hold (HOLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Write Protect (W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
VCC supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
VSS ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3
4
SPI modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operating features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Page programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Sector Erase and Bulk Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Polling during a Write, Program or Erase cycle . . . . . . . . . . . . . . . . . . . . 12
Active Power, Standby Power and Deep Power-down modes . . . . . . . . . 12
Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Protection modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Hold condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5
6
Memory organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.1
6.2
6.3
6.4
Write Enable (WREN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Write Disable (WRDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Read Identification (RDID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Read Status Register (RDSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.4.1
6.4.2
6.4.3
WIP bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
WEL bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
BP2, BP1, BP0 bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2/55
M25P16
Contents
6.4.4
SRWD bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.5
6.6
6.7
6.8
6.9
Write Status Register (WRSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Read Data Bytes (READ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Read Data Bytes at Higher Speed (FAST_READ) . . . . . . . . . . . . . . . . . . 27
Page Program (PP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Sector Erase (SE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.10 Bulk Erase (BE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.11 Deep Power-down (DP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.12 Release from Deep Power-down and Read Electronic Signature (RES) . 33
7
Power-up and power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Initial delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
8
9
10
11
12
13
3/55
List of tables
M25P16
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Protected area sizes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Memory organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Instruction set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Read Identification (RDID) data-out sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Status Register format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Protection modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Power-up timing and V threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
WI
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Operating conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Data retention and endurance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
AC characteristics (grade 6, T9HX technology) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
AC characteristics (25 MHz operation, grade 3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
VFQFPN8 (MLP8) 8-lead very thin fine pitch quad flat package no lead,
6 × 5 mm, package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
VDFPN8 (MLP8) 8-lead very thin dual flat package no lead, 8 × 6 mm,
package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SO8N – 8 lead plastic small outline, 150 mils body width, package
mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
SO8 wide – 8 lead plastic small outline, 208 mils body width,
Table 18.
Table 19.
Table 20.
package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
SO16 wide – 16-lead plastic small outline, 300 mils body width, mechanical data . . . . . . 51
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 21.
Table 22.
Table 23.
4/55
M25P16
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SO8, VFQFPN and VDFPN connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SO16 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Bus master and memory devices on the SPI bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SPI modes supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hold condition activation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Write Enable (WREN) instruction sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Write Disable (WRDI) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 10. Read Identification (RDID) instruction sequence and data-out sequence . . . . . . . . . . . . . 21
Figure 11. Read Status Register (RDSR) instruction sequence and data-out sequence . . . . . . . . . . 23
Figure 12. Write Status Register (WRSR) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 13. Read Data Bytes (READ) instruction sequence and data-out sequence . . . . . . . . . . . . . . 26
Figure 14. Read Data Bytes at Higher Speed (FAST_READ) instruction sequence
and data-out sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 15. Page Program (PP) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 16. Sector Erase (SE) instruction sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 17. Bulk Erase (BE) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 18. Deep Power-down (DP) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 19. Release from Deep Power-down and Read Electronic Signature (RES) instruction
sequence and data-out sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 20. Release from Deep Power-down (RES) instruction sequence . . . . . . . . . . . . . . . . . . . . . . 34
Figure 21. Power-up timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 22. AC measurement I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 23. Serial input timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 24. Write Protect setup and hold timing during WRSR when SRWD = 1 . . . . . . . . . . . . . . . . . 44
Figure 25. Hold timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 26. Output timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 27. VFQFPN8 (MLP8) 8-lead very thin fine pitch quad flat package no lead,
6 × 5 mm, package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 28. VDFPN8 (MLP8) 8-lead very thin dual flat package no lead, 8 × 6 mm,
package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 29. SO8N – 8 lead plastic small outline, 150 mils body width, package outline . . . . . . . . . . . . 49
Figure 30. SO8W – 8 lead plastic small outline, 208 mils body width, package outline. . . . . . . . . . . . 50
Figure 31. SO16 wide – 16-lead plastic small outline, 300 mils body width, package outline . . . . . . . 51
5/55
Description
M25P16
1
Description
The M25P16 is a 16 Mbit (2 Mbit × 8) serial Flash memory, with advanced write protection
mechanisms, accessed by a high speed SPI-compatible bus.
The memory can be programmed 1 to 256 bytes at a time, using the Page Program
instruction.
The memory is organized as 32 sectors, each containing 256 pages. Each page is 256
bytes wide. Thus, the whole memory can be viewed as consisting of 8192 pages, or 2 097
152 bytes.
The whole memory can be erased using the Bulk Erase instruction, or a sector at a time,
using the Sector Erase instruction.
Figure 1.
Logic diagram
V
CC
D
C
S
Q
M25P16
W
HOLD
V
SS
AI05762
Table 1.
Signal names
Signal name
Function
Direction
C
Serial Clock
Input
D
Serial Data input
Input
Output
Input
Input
Input
Q
Serial Data output
Chip Select
Write Protect
Hold
S
W
HOLD
VCC
VSS
Supply voltage
Ground
6/55
M25P16
Description
Figure 2.
SO8, VFQFPN and VDFPN connections
M25P16
S
Q
1
2
3
4
8
V
CC
HOLD
7
6
W
C
D
V
5
SS
AI08517
1. There is an exposed central pad on the underside of the VFQFPN package. This is pulled, internally, to
VSS, and must not be allowed to be connected to any other voltage or signal line on the PCB.
2. See Package mechanical section for package dimensions, and how to identify pin-1.
Figure 3.
SO16 connections
M25P16
HOLD
1
16
15
C
V
2
3
4
5
6
7
8
D
CC
DU
14
DU
DU
DU
DU
DU
DU
DU
S
13
12
11
10
V
SS
W
Q
9
AI08594B
1. DU = Don’t use
2. See Package mechanical section for package dimensions, and how to identify pin-1.
7/55
Signal description
M25P16
2
Signal description
2.1
Serial Data output (Q)
This output signal is used to transfer data serially out of the device. Data is shifted out on the
falling edge of Serial Clock (C).
2.2
2.3
2.4
Serial Data input (D)
This input signal is used to transfer data serially into the device. It receives instructions,
addresses, and the data to be programmed. Values are latched on the rising edge of Serial
Clock (C).
Serial Clock (C)
This input signal provides the timing of the serial interface. Instructions, addresses, or data
present at Serial Data input (D) are latched on the rising edge of Serial Clock (C). Data on
Serial Data output (Q) changes after the falling edge of Serial Clock (C).
Chip Select (S)
When this input signal is High, the device is deselected and Serial Data output (Q) is at high
impedance. Unless an internal Program, Erase or Write Status Register cycle is in progress,
the device will be in the Standby mode (this is not the Deep Power-down mode). Driving
Chip Select (S) Low selects the device, placing it in the Active Power mode.
After power-up, a falling edge on Chip Select (S) is required prior to the start of any
instruction.
2.5
2.6
Hold (HOLD)
The Hold (HOLD) signal is used to pause any serial communications with the device without
deselecting the device.
During the Hold condition, the Serial Data output (Q) is high impedance, and Serial Data
input (D) and Serial Clock (C) are Don’t care.
To start the Hold condition, the device must be selected, with Chip Select (S) driven Low.
Write Protect (W)
The main purpose of this input signal is to freeze the size of the area of memory that is
protected against program or erase instructions (as specified by the values in the BP2, BP1
and BP0 bits of the Status Register).
8/55
M25P16
Signal description
2.7
VCC supply voltage
V
is the supply voltage.
CC
2.8
VSS ground
V
is the reference for the V supply voltage.
CC
SS
9/55
SPI modes
M25P16
3
SPI modes
These devices can be driven by a microcontroller with its SPI peripheral running in either of
the two following modes:
●
CPOL=0, CPHA=0
CPOL=1, CPHA=1
●
For these two modes, input data is latched in on the rising edge of Serial Clock (C), and
output data is available from the falling edge of Serial Clock (C).
The difference between the two modes, as shown in Figure 5, is the clock polarity when the
bus master is in Standby mode and not transferring data:
●
C remains at 0 for (CPOL=0, CPHA=0)
C remains at 1 for (CPOL=1, CPHA=1)
●
Figure 4.
Bus master and memory devices on the SPI bus
V
V
SS
CC
R
SDO
SPI interface with
(CPOL, CPHA) =
(0, 0) or (1, 1)
SDI
SCK
V
V
CC
C
Q
D
C
Q
D
C Q D
V
CC
CC
V
V
R
V
SS
SS
SS
SPI Bus Master
SPI memory
device
SPI memory
device
SPI memory
device
R
R
CS3 CS2 CS1
S
S
S
W
HOLD
W
HOLD
HOLD
W
AI12836b
1. The Write Protect (W) and Hold (HOLD) signals should be driven, High or Low as appropriate.
Figure 4 shows an example of three devices connected to an MCU, on an SPI bus. Only one
device is selected at a time, so only one device drives the Serial Data output (Q) line at a
time, the other devices are high impedance. Resistors R (represented in Figure 4) ensure
that the M25P16 is not selected if the Bus Master leaves the S line in the high impedance
state. As the Bus Master may enter a state where all inputs/outputs are in high impedance
at the same time (for example, when the Bus Master is reset), the clock line (C) must be
connected to an external pull-down resistor so that, when all inputs/outputs become high
impedance, the S line is pulled High while the C line is pulled Low (thus ensuring that S and
C do not become High at the same time, and so, that the t
requirement is met). The
SHCH
typical value of R is 100 kΩ, assuming that the time constant R*C (C = parasitic
p
p
capacitance of the bus line) is shorter than the time during which the Bus Master leaves the
SPI bus in high impedance.
10/55
M25P16
SPI modes
Example: C = 50 pF, that is R*C = 5 µs <=> the application must ensure that the Bus
p
p
Master never leaves the SPI bus in the high impedance state for a time period shorter than
5 µs.
Figure 5.
SPI modes supported
CPOL CPHA
C
0
1
0
1
C
D
MSB
Q
MSB
AI01438B
11/55
Operating features
M25P16
4
Operating features
4.1
Page programming
To program one data byte, two instructions are required: Write Enable (WREN), which is one
byte, and a Page Program (PP) sequence, which consists of four bytes plus data. This is
followed by the internal Program cycle (of duration t ).
PP
To spread this overhead, the Page Program (PP) instruction allows up to 256 bytes to be
programmed at a time (changing bits from 1 to 0), provided that they lie in consecutive
addresses on the same page of memory.
For optimized timings, it is recommended to use the Page Program (PP) instruction to
program all consecutive targeted bytes in a single sequence versus using several Page
Program (PP) sequences with each containing only a few bytes (see Page Program (PP)).
4.2
Sector Erase and Bulk Erase
The Page Program (PP) instruction allows bits to be reset from 1 to 0. Before this can be
applied, the bytes of memory need to have been erased to all 1s (FFh). This can be
achieved either a sector at a time, using the Sector Erase (SE) instruction, or throughout the
entire memory, using the Bulk Erase (BE) instruction. This starts an internal Erase cycle (of
duration t or t ).
SE
BE
The Erase instruction must be preceded by a Write Enable (WREN) instruction.
4.3
4.4
Polling during a Write, Program or Erase cycle
A further improvement in the time to Write Status Register (WRSR), Program (PP) or Erase
(SE or BE) can be achieved by not waiting for the worst case delay (t , t , t , or t ). The
W
PP SE
BE
Write In Progress (WIP) bit is provided in the Status Register so that the application program
can monitor its value, polling it to establish when the previous Write cycle, Program cycle or
Erase cycle is complete.
Active Power, Standby Power and Deep Power-down modes
When Chip Select (S) is Low, the device is selected, and in the Active Power mode.
When Chip Select (S) is High, the device is deselected, but could remain in the Active Power
mode until all internal cycles have completed (Program, Erase, Write Status Register). The
device then goes in to the Standby Power mode. The device consumption drops to I
.
CC1
The Deep Power-down mode is entered when the specific instruction (the Deep Power-
down (DP) instruction) is executed. The device consumption drops further to I . The
CC2
device remains in this mode until another specific instruction (the Release from Deep
Power-down and Read Electronic Signature (RES) instruction) is executed.
While in the Deep Power-down mode, the device ignores all Write, Program and Erase
instructions (see Deep Power-down (DP)). This can be used as an extra software protection
mechanism, when the device is not in active use, to protect the device from inadvertent
Write, Program or Erase instructions.
12/55
M25P16
Operating features
4.5
Status Register
The Status Register contains a number of status and control bits that can be read or set (as
appropriate) by specific instructions. See Section 6.4: Read Status Register (RDSR) for a
detailed description of the Status Register bits.
4.6
Protection modes
The environments where non-volatile memory devices are used can be very noisy. No SPI
device can operate correctly in the presence of excessive noise. To help combat this, the
M25P16 features the following data protection mechanisms:
●
Power on reset and an internal timer (t
) can provide protection against inadvertent
PUW
changes while the power supply is outside the operating specification
●
Program, Erase and Write Status Register instructions are checked that they consist of
a number of clock pulses that is a multiple of eight, before they are accepted for
execution
●
All instructions that modify data must be preceded by a Write Enable (WREN)
instruction to set the Write Enable Latch (WEL) bit. This bit is returned to its reset state
by the following events:
–
–
–
–
–
–
Power-up
Write Disable (WRDI) instruction completion
Write Status Register (WRSR) instruction completion
Page Program (PP) instruction completion
Sector Erase (SE) instruction completion
Bulk Erase (BE) instruction completion
●
●
The Block Protect (BP2, BP1, BP0) bits allow part of the memory to be configured as
read-only. This is the software protected mode (SPM)
The Write Protect (W) signal allows the Block Protect (BP2, BP1, BP0) bits and Status
Register Write Disable (SRWD) bit to be protected. This is the hardware protected
mode (HPM)
●
In addition to the low power consumption feature, the Deep Power-down mode offers
extra software protection, as all Write, Program and Erase instructions are ignored.
13/55
Operating features
Table 2.
M25P16
Protected area sizes
StatusRegister
Memory content
content
BP2 BP1 BP0
bit bit bit
Protected area
Unprotected area
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
none
Upper 32nd (Sector 31)
Upper sixteenth (2 sectors: 30 and 31) Lower 15/16ths (30 sectors: 0 to 29)
All sectors(1) (32 sectors: 0 to 31)
Lower 31/32nds (31 sectors: 0 to 30)
Upper eighth (4 sectors: 28 to 31)
Upper quarter (8 sectors: 24 to 31)
Upper half (16 sectors: 16 to 31)
All sectors (32 sectors: 0 to 31)
All sectors (32 sectors: 0 to 31)
Lower seven-eighths (28 sectors: 0 to 27)
Lower three-quarters (24 sectors: 0 to 23)
Lower half (16 sectors: 0 to 15)
none
none
1. The device is ready to accept a Bulk Erase instruction if, and only if, all Block Protect (BP2, BP1, BP0) are
0.
4.7
Hold condition
The Hold (HOLD) signal is used to pause any serial communications with the device without
resetting the clocking sequence. However, taking this signal Low does not terminate any
Write Status Register, Program or Erase cycle that is currently in progress.
To enter the Hold condition, the device must be selected, with Chip Select (S) Low.
The Hold condition starts on the falling edge of the Hold (HOLD) signal, provided that this
coincides with Serial Clock (C) being Low (as shown in Figure 6).
The Hold condition ends on the rising edge of the Hold (HOLD) signal, provided that this
coincides with Serial Clock (C) being Low.
If the falling edge does not coincide with Serial Clock (C) being Low, the Hold condition
starts after Serial Clock (C) next goes Low. Similarly, if the rising edge does not coincide
with Serial Clock (C) being Low, the Hold condition ends after Serial Clock (C) next goes
Low (this is shown in Figure 6).
During the Hold condition, the Serial Data output (Q) is high impedance, and Serial Data
input (D) and Serial Clock (C) are Don’t care.
Normally, the device is kept selected, with Chip Select (S) driven Low, for the whole duration
of the Hold condition. This is to ensure that the state of the internal logic remains unchanged
from the moment of entering the Hold condition.
If Chip Select (S) goes High while the device is in the Hold condition, this has the effect of
resetting the internal logic of the device. To restart communication with the device, it is
necessary to drive Hold (HOLD) High, and then to drive Chip Select (S) Low. This prevents
the device from going back to the Hold condition.
14/55
M25P16
Operating features
Figure 6.
Hold condition activation
C
HOLD
Hold
Hold
condition
condition
(standard use)
(non-standard use)
AI02029D
15/55
Memory organization
M25P16
5
Memory organization
The memory is organized as:
●
●
●
2 097 152 bytes (8 bits each)
32 sectors (512 Kbits, 65536 bytes each)
8192 pages (256 bytes each).
Each page can be individually programmed (bits are programmed from 1 to 0). The device is
sector or bulk erasable (bits are erased from 0 to 1) but not page erasable.
Figure 7.
Block diagram
HOLD
W
High voltage
Generator
Control Logic
S
C
D
Q
I/O Shift Register
Status
Register
Address Register
and Counter
256 byte
Data Buffer
1FFFFFh
Size of the
read-only
memory area
00000h
000FFh
256 bytes (page size)
X Decoder
AI04987
16/55
M25P16
Memory organization
Table 3.
Memory organization
Sector
Address range
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
1F0000h
1E0000h
1D0000h
1C0000h
1B0000h
1A0000h
190000h
180000h
170000h
160000h
150000h
140000h
130000h
120000h
110000h
100000h
0F0000h
0E0000h
0D0000h
0C0000h
0B0000h
0A0000h
090000h
080000h
070000h
060000h
050000h
040000h
030000h
020000h
010000h
000000h
1FFFFFh
1EFFFFh
1DFFFFh
1CFFFFh
1BFFFFh
1AFFFFh
19FFFFh
18FFFFh
17FFFFh
16FFFFh
15FFFFh
14FFFFh
13FFFFh
12FFFFh
11FFFFh
10FFFFh
0FFFFFh
0EFFFFh
0DFFFFh
0CFFFFh
0BFFFFh
0AFFFFh
09FFFFh
08FFFFh
07FFFFh
06FFFFh
05FFFFh
04FFFFh
03FFFFh
02FFFFh
01FFFFh
00FFFFh
8
7
6
5
4
3
2
1
0
17/55
Instructions
M25P16
6
Instructions
All instructions, addresses and data are shifted in and out of the device, most significant bit
first.
Serial Data input (D) is sampled on the first rising edge of Serial Clock (C) after Chip Select
(S) is driven Low. Then, the one-byte instruction code must be shifted in to the device, most
significant bit first, on Serial Data input (D), each bit being latched on the rising edges of
Serial Clock (C).
The instruction set is listed in Table 4.
Every instruction sequence starts with a one-byte instruction code. Depending on the
instruction, this might be followed by address bytes, or by data bytes, or by both or none.
In the case of a Read Data Bytes (READ), Read Data Bytes at Higher Speed
(FAST_READ), Read Status Register (RDSR), Read Identification (RDID) or Release from
Deep Power-down, and Read Electronic Signature (RES) instruction, the shifted-in
instruction sequence is followed by a data-out sequence. Chip Select (S) can be driven High
after any bit of the data-out sequence is being shifted out.
In the case of a Page Program (PP), Sector Erase (SE), Bulk Erase (BE), Write Status
Register (WRSR), Write Enable (WREN), Write Disable (WRDI) or Deep Power-down (DP)
instruction, Chip Select (S) must be driven High exactly at a byte boundary, otherwise the
instruction is rejected, and is not executed. That is, Chip Select (S) must driven High when
the number of clock pulses after Chip Select (S) being driven Low is an exact multiple of
eight.
All attempts to access the memory array during a Write Status Register cycle, Program
cycle or Erase cycle are ignored, and the internal Write Status Register cycle, Program
cycle or Erase cycle continues unaffected.
Note:
Output Hi-Z is defined as the point where data out is no longer driven.
18/55
M25P16
Instructions
Table 4.
Instruction set
Description
One-byte instruction Address Dummy
Data
Instruction
code
bytes
bytes
bytes
WREN
WRDI
RDID
Write Enable
0000 0110
0000 0100
1001 1111
0000 0101
0000 0001
0000 0011
06h
04h
9Fh
05h
01h
03h
0
0
0
0
0
3
0
0
0
0
0
0
0
0
Write Disable
Read Identification
Read Status Register
Write Status Register
Read Data Bytes
1 to 20
1 to ∞
1
RDSR
WRSR
READ
1 to ∞
Read Data Bytes at Higher
Speed
FAST_READ
0000 1011
0Bh
3
1
1 to ∞
PP
SE
BE
DP
Page Program
Sector Erase
Bulk Erase
0000 0010
1101 1000
1100 0111
1011 1001
02h
D8h
C7h
B9h
3
3
0
0
0
0
0
0
1 to 256
0
0
0
Deep Power-down
Release from Deep
Power-down, and Read
Electronic Signature
0
0
3
0
1 to ∞
RES
1010 1011
ABh
Release from Deep
Power-down
0
6.1
Write Enable (WREN)
The Write Enable (WREN) instruction (Figure 8) sets the Write Enable Latch (WEL) bit.
The Write Enable Latch (WEL) bit must be set prior to every Page Program (PP), Sector
Erase (SE), Bulk Erase (BE) and Write Status Register (WRSR) instruction.
The Write Enable (WREN) instruction is entered by driving Chip Select (S) Low, sending the
instruction code, and then driving Chip Select (S) High.
Figure 8.
Write Enable (WREN) instruction sequence
S
0
1
2
3
4
5
6
7
C
D
Q
Instruction
High Impedance
AI02281E
19/55
Instructions
M25P16
6.2
Write Disable (WRDI)
The Write Disable (WRDI) instruction (Figure 9) resets the Write Enable Latch (WEL) bit.
The Write Disable (WRDI) instruction is entered by driving Chip Select (S) Low, sending the
instruction code, and then driving Chip Select (S) High.
The Write Enable Latch (WEL) bit is reset under the following conditions:
●
Power-up
●
●
●
●
●
Write Disable (WRDI) instruction completion
Write Status Register (WRSR) instruction completion
Page Program (PP) instruction completion
Sector Erase (SE) instruction completion
Bulk Erase (BE) instruction completion
Figure 9.
Write Disable (WRDI) instruction sequence
S
0
1
2
3
4
5
6
7
C
D
Q
Instruction
High Impedance
AI03750D
20/55
M25P16
Instructions
6.3
Read Identification (RDID)
The Read Identification (RDID) instruction allows to read the device identification data:
●
●
●
Manufacturer identification (1 byte)
Device identification (2 bytes)
A Unique ID code (UID) (17 bytes, of which 16 available upon customer request).
The manufacturer identification is assigned by JEDEC, and has the value 20h for Numonyx.
The device identification is assigned by the device manufacturer, and indicates the memory
type in the first byte (20h), and the memory capacity of the device in the second byte (15h).
The UID contains the length of the following data in the first byte (set to 10h), and 16 bytes
of the optional Customized Factory Data (CFD) content. The CFD bytes are read-only and
can be programmed with customers data upon their demand. If the customers do not make
requests, the devices are shipped with all the CFD bytes programmed to zero (00h).
Any Read Identification (RDID) instruction while an Erase or Program cycle is in progress, is
not decoded, and has no effect on the cycle that is in progress.
The device is first selected by driving Chip Select (S) Low. Then, the 8-bit instruction code
for the instruction is shifted in. After this, the 24-bit device identification, stored in the
memory, the 8-bit CFD length followed by 16 bytes of CFD content will be shifted out on
Serial Data output (Q). Each bit is shifted out during the falling edge of Serial Clock (C).
The instruction sequence is shown in Figure 10.
The Read Identification (RDID) instruction is terminated by driving Chip Select (S) High at
any time during data output.
When Chip Select (S) is driven High, the device is put in the Standby Power mode. Once in
the Standby Power mode, the device waits to be selected, so that it can receive, decode and
execute instructions.
Table 5.
Read Identification (RDID) data-out sequence
Device identification
UID
Manufacturer
identification
Memory type
20h
Memory capacity
CFD length
CFD content
20h
15h
10h
16 bytes
Figure 10. Read Identification (RDID) instruction sequence and data-out sequence
S
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
16 17 18
28 29 30 31
C
D
Instruction
Manufacturer identification
Device identification
UID
High Impedance
Q
15 14 13
MSB
3
2
1
0
MSB
MSB
AI06809c
21/55
Instructions
M25P16
6.4
Read Status Register (RDSR)
The Read Status Register (RDSR) instruction allows the Status Register to be read. The
Status Register may be read at any time, even while a Program, Erase or Write Status
Register cycle is in progress. When one of these cycles is in progress, it is recommended to
check the Write In Progress (WIP) bit before sending a new instruction to the device. It is
also possible to read the Status Register continuously, as shown in Figure 11.
Table 6.
Status Register format
b7
b0
SRWD
0
0
BP2
BP1
BP0
WEL
WIP
Status Register Write Protect
Block Protect bits
Write Enable Latch bit
Write In Progress bit
The status and control bits of the Status Register are as follows:
6.4.1
6.4.2
WIP bit
The Write In Progress (WIP) bit indicates whether the memory is busy with a Write Status
Register, Program or Erase cycle. When set to ‘1’, such a cycle is in progress, when reset to
‘0’ no such cycle is in progress.
WEL bit
The Write Enable Latch (WEL) bit indicates the status of the internal Write Enable Latch.
When set to ‘1’ the internal Write Enable Latch is set, when set to ‘0’ the internal Write
Enable Latch is reset and no Write Status Register, Program or Erase instruction is
accepted.
6.4.3
BP2, BP1, BP0 bits
The Block Protect (BP2, BP1, BP0) bits are non-volatile. They define the size of the area to
be software protected against Program and Erase instructions. These bits are written with
the Write Status Register (WRSR) instruction. When one or more of the Block Protect (BP2,
BP1, BP0) bits is set to ‘1’, the relevant memory area (as defined in Table 2) becomes
protected against Page Program (PP) and Sector Erase (SE) instructions. The Block Protect
(BP2, BP1, BP0) bits can be written provided that the Hardware Protected mode has not
been set. The Bulk Erase (BE) instruction is executed if, and only if, all Block Protect (BP2,
BP1, BP0) bits are 0.
22/55
M25P16
Instructions
6.4.4
SRWD bit
The Status Register Write Disable (SRWD) bit is operated in conjunction with the Write
Protect (W) signal. The Status Register Write Disable (SRWD) bit and Write Protect (W)
signal allow the device to be put in the Hardware Protected mode (when the Status Register
Write Disable (SRWD) bit is set to ‘1’, and Write Protect (W) is driven Low). In this mode, the
non-volatile bits of the Status Register (SRWD, BP2, BP1, BP0) become read-only bits and
the Write Status Register (WRSR) instruction is no longer accepted for execution.
Figure 11. Read Status Register (RDSR) instruction sequence and data-out
sequence
S
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
C
D
Instruction
Status Register Out
Status Register Out
High Impedance
Q
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
MSB
MSB
AI02031E
23/55
Instructions
M25P16
6.5
Write Status Register (WRSR)
The Write Status Register (WRSR) instruction allows new values to be written to the Status
Register. Before it can be accepted, a Write Enable (WREN) instruction must previously
have been executed. After the Write Enable (WREN) instruction has been decoded and
executed, the device sets the Write Enable Latch (WEL).
The Write Status Register (WRSR) instruction is entered by driving Chip Select (S) Low,
followed by the instruction code and the data byte on Serial Data input (D).
The instruction sequence is shown in Figure 12.
The Write Status Register (WRSR) instruction has no effect on b6, b5, b1 and b0 of the
Status Register. b6 and b5 are always read as 0.
Chip Select (S) must be driven High after the eighth bit of the data byte has been latched in.
If not, the Write Status Register (WRSR) instruction is not executed. As soon as Chip Select
(S) is driven High, the self-timed Write Status Register cycle (whose duration is t ) is
W
initiated. While the Write Status Register cycle is in progress, the Status Register may still
be read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP)
bit is 1 during the self-timed Write Status Register cycle, and is 0 when it is completed.
When the cycle is completed, the Write Enable Latch (WEL) is reset.
The Write Status Register (WRSR) instruction allows the user to change the values of the
Block Protect (BP2, BP1, BP0) bits, to define the size of the area that is to be treated as
read-only, as defined in Table 2. The Write Status Register (WRSR) instruction also allows
the user to set or reset the Status Register Write Disable (SRWD) bit in accordance with the
Write Protect (W) signal. The Status Register Write Disable (SRWD) bit and Write Protect
(W) signal allow the device to be put in the Hardware Protected mode (HPM). The Write
Status Register (WRSR) instruction is not executed once the Hardware Protected mode
(HPM) is entered.
Figure 12. Write Status Register (WRSR) instruction sequence
S
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
C
Instruction
Status
Register In
7
6
5
4
3
2
0
1
D
Q
High Impedance
MSB
AI02282D
24/55
M25P16
Instructions
Table 7.
Protection modes
Memory content
Protected area(1) Unprotected area(1)
W
signal
SRWD
bit
Write Protection of the
Mode
Status Register
1
0
0
0
Status Register is writable
(if the WREN instruction
has set the WEL bit)
Software
Protected
mode
Protected against
Page Program,
Sector Erase and
Bulk Erase
Ready to accept
Page Program and
Sector Erase
The values in the SRWD,
BP2, BP1 and BP0 bits
can be changed
(SPM)
instructions
1
1
Status Register is
Hardware write protected
Hardware
Protected
mode
Protected against
Page Program,
Sector Erase and
Bulk Erase
Ready to accept
Page Program and
Sector Erase
0
1
The values in the SRWD,
BP2, BP1 and BP0 bits
cannot be changed
(HPM)
instructions
1. As defined by the values in the Block Protect (BP2, BP1, BP0) bits of the Status Register, as shown in
Table 6.
The protection features of the device are summarized in Table 7.
When the Status Register Write Disable (SRWD) bit of the Status Register is 0 (its initial
delivery state), it is possible to write to the Status Register provided that the Write Enable
Latch (WEL) bit has previously been set by a Write Enable (WREN) instruction, regardless
of the whether Write Protect (W) is driven High or Low.
When the Status Register Write Disable (SRWD) bit of the Status Register is set to ‘1’, two
cases need to be considered, depending on the state of Write Protect (W):
●
●
If Write Protect (W) is driven High, it is possible to write to the Status Register provided
that the Write Enable Latch (WEL) bit has previously been set by a Write Enable
(WREN) instruction
If Write Protect (W) is driven Low, it is not possible to write to the Status Register even
if the Write Enable Latch (WEL) bit has previously been set by a Write Enable (WREN)
instruction (attempts to write to the Status Register are rejected, and are not accepted
for execution). As a consequence, all the data bytes in the memory area that are
software protected (SPM) by the Block Protect (BP2, BP1, BP0) bits of the Status
Register, are also hardware protected against data modification.
Regardless of the order of the two events, the Hardware Protected mode (HPM) can be
entered:
●
by setting the Status Register Write Disable (SRWD) bit after driving Write Protect (W)
Low
●
or by driving Write Protect (W) Low after setting the Status Register Write Disable
(SRWD) bit.
The only way to exit the Hardware Protected mode (HPM) once entered is to pull Write
Protect (W) High.
If Write Protect (W) is permanently tied High, the Hardware Protected mode (HPM) can
never be activated, and only the Software Protected mode (SPM), using the Block Protect
(BP2, BP1, BP0) bits of the Status Register, can be used.
25/55
Instructions
M25P16
6.6
Read Data Bytes (READ)
The device is first selected by driving Chip Select (S) Low. The instruction code for the Read
Data Bytes (READ) instruction is followed by a 3-byte address (A23-A0), each bit being
latched-in during the rising edge of Serial Clock (C). Then the memory contents, at that
address, is shifted out on Serial Data output (Q), each bit being shifted out, at a maximum
frequency f , during the falling edge of Serial Clock (C).
R
The instruction sequence is shown in Figure 13.
The first byte addressed can be at any location. The address is automatically incremented
to the next higher address after each byte of data is shifted out. The whole memory can,
therefore, be read with a single Read Data Bytes (READ) instruction. When the highest
address is reached, the address counter rolls over to 000000h, allowing the read sequence
to be continued indefinitely.
The Read Data Bytes (READ) instruction is terminated by driving Chip Select (S) High. Chip
Select (S) can be driven High at any time during data output. Any Read Data Bytes (READ)
instruction, while an Erase, Program or Write cycle is in progress, is rejected without having
any effects on the cycle that is in progress.
Figure 13. Read Data Bytes (READ) instruction sequence and data-out sequence
S
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31 32 33 34 35 36 37 38 39
C
Instruction
24-bit address
23 22 21
MSB
3
2
1
0
D
Q
Data Out 1
Data Out 2
7
High Impedance
2
7
6
5
4
3
1
0
MSB
AI03748D
1. Address bits A23 to A21 are Don’t care.
26/55
M25P16
Instructions
6.7
Read Data Bytes at Higher Speed (FAST_READ)
The device is first selected by driving Chip Select (S) Low. The instruction code for the Read
Data Bytes at Higher Speed (FAST_READ) instruction is followed by a 3-byte address (A23-
A0) and a dummy byte, each bit being latched-in during the rising edge of Serial Clock (C).
Then the memory contents, at that address, is shifted out on Serial Data output (Q), each bit
being shifted out, at a maximum frequency f , during the falling edge of Serial Clock (C).
C
The instruction sequence is shown in Figure 14.
The first byte addressed can be at any location. The address is automatically incremented
to the next higher address after each byte of data is shifted out. The whole memory can,
therefore, be read with a single Read Data Bytes at Higher Speed (FAST_READ)
instruction. When the highest address is reached, the address counter rolls over to
000000h, allowing the read sequence to be continued indefinitely.
The Read Data Bytes at Higher Speed (FAST_READ) instruction is terminated by driving
Chip Select (S) High. Chip Select (S) can be driven High at any time during data output. Any
Read Data Bytes at Higher Speed (FAST_READ) instruction, while an Erase, Program or
Write cycle is in progress, is rejected without having any effects on the cycle that is in
progress.
Figure 14. Read Data Bytes at Higher Speed (FAST_READ) instruction sequence
and data-out sequence
S
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
C
Instruction
24-bit address
23 22 21
3
2
1
0
D
Q
High Impedance
S
C
47
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
Dummy byte
7
6
5
4
3
2
0
1
D
Q
DATA OUT 2
DATA OUT 1
7
6
5
4
3
2
1
0
7
7
6
5
4
3
2
0
1
MSB
MSB
MSB
AI04006
1. Address bits A23 to A21 are Don’t care.
27/55
Instructions
M25P16
6.8
Page Program (PP)
The Page Program (PP) instruction allows bytes to be programmed in the memory
(changing bits from 1 to 0). Before it can be accepted, a Write Enable (WREN) instruction
must previously have been executed. After the Write Enable (WREN) instruction has been
decoded, the device sets the Write Enable Latch (WEL).
The Page Program (PP) instruction is entered by driving Chip Select (S) Low, followed by
the instruction code, three address bytes and at least one data byte on Serial Data input (D).
If the 8 least significant address bits (A7-A0) are not all zero, all transmitted data that goes
beyond the end of the current page are programmed from the start address of the same
page (from the address whose 8 least significant bits (A7-A0) are all zero). Chip Select (S)
must be driven Low for the entire duration of the sequence.
The instruction sequence is shown in Figure 15.
If more than 256 bytes are sent to the device, previously latched data are discarded and the
last 256 data bytes are guaranteed to be programmed correctly within the same page. If less
than 256 data bytes are sent to device, they are correctly programmed at the requested
addresses without having any effects on the other bytes of the same page.
For optimized timings, it is recommended to use the Page Program (PP) instruction to
program all consecutive targeted bytes in a single sequence versus using several Page
Program (PP) sequences with each containing only a few bytes.
Chip Select (S) must be driven High after the eighth bit of the last data byte has been
latched in, otherwise the Page Program (PP) instruction is not executed.
As soon as Chip Select (S) is driven High, the self-timed Page Program cycle (whose
duration is t ) is initiated. While the Page Program cycle is in progress, the Status Register
PP
may be read to check the value of the Write In Progress (WIP) bit. The Write In Progress
(WIP) bit is 1 during the self-timed Page Program cycle, and is 0 when it is completed. At
some unspecified time before the cycle is completed, the Write Enable Latch (WEL) bit is
reset.
A Page Program (PP) instruction applied to a page which is protected by the Block Protect
(BP2, BP1, BP0) bits (see Table 2 and Table 3) is not executed.
28/55
M25P16
Instructions
Figure 15. Page Program (PP) instruction sequence
S
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31 32 33 34 35 36 37 38 39
C
D
Instruction
24-bit address
Data byte 1
23 22 21
MSB
3
2
1
0
7
6
5
4
3
2
0
1
MSB
S
C
40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
Data byte 2
Data byte 3
Data byte 256
7
6
5
4
3
2
0
7
6
5
4
3
2
0
7
6
5
4
3
2
0
1
1
1
D
MSB
MSB
MSB
AI04082B
1. Address bits A23 to A21 are Don’t care.
29/55
Instructions
M25P16
6.9
Sector Erase (SE)
The Sector Erase (SE) instruction sets to ‘1’ (FFh) all bits inside the chosen sector. Before it
can be accepted, a Write Enable (WREN) instruction must previously have been executed.
After the Write Enable (WREN) instruction has been decoded, the device sets the Write
Enable Latch (WEL).
The Sector Erase (SE) instruction is entered by driving Chip Select (S) Low, followed by the
instruction code, and three address bytes on Serial Data input (D). Any address inside the
sector (see Table 3) is a valid address for the Sector Erase (SE) instruction. Chip Select (S)
must be driven Low for the entire duration of the sequence.
The instruction sequence is shown in Figure 16.
Chip Select (S) must be driven High after the eighth bit of the last address byte has been
latched in, otherwise the Sector Erase (SE) instruction is not executed. As soon as Chip
Select (S) is driven High, the self-timed Sector Erase cycle (whose duration is t ) is
SE
initiated. While the Sector Erase cycle is in progress, the Status Register may be read to
check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1
during the self-timed Sector Erase cycle, and is 0 when it is completed. At some unspecified
time before the cycle is completed, the Write Enable Latch (WEL) bit is reset.
A Sector Erase (SE) instruction applied to a page which is protected by the Block Protect
(BP2, BP1, BP0) bits (see Table 2 and Table 3) is not executed.
Figure 16. Sector Erase (SE) instruction sequence
S
0
1
2
3
4
5
6
7
8
9
29 30 31
C
D
Instruction
24 Bit Address
23 22
MSB
2
0
1
AI03751D
1. Address bits A23 to A21 are Don’t care.
30/55
M25P16
Instructions
6.10
Bulk Erase (BE)
The Bulk Erase (BE) instruction sets all bits to ‘1’ (FFh). Before it can be accepted, a Write
Enable (WREN) instruction must previously have been executed. After the Write Enable
(WREN) instruction has been decoded, the device sets the Write Enable Latch (WEL).
The Bulk Erase (BE) instruction is entered by driving Chip Select (S) Low, followed by the
instruction code on Serial Data input (D). Chip Select (S) must be driven Low for the entire
duration of the sequence.
The instruction sequence is shown in Figure 17.
Chip Select (S) must be driven High after the eighth bit of the instruction code has been
latched in, otherwise the Bulk Erase instruction is not executed. As soon as Chip Select (S)
is driven High, the self-timed Bulk Erase cycle (whose duration is t ) is initiated. While the
BE
Bulk Erase cycle is in progress, the Status Register may be read to check the value of the
Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the self-timed Bulk
Erase cycle, and is 0 when it is completed. At some unspecified time before the cycle is
completed, the Write Enable Latch (WEL) bit is reset.
The Bulk Erase (BE) instruction is executed only if all Block Protect (BP2, BP1, BP0) bits are
0. The Bulk Erase (BE) instruction is ignored if one, or more, sectors are protected.
Figure 17. Bulk Erase (BE) instruction sequence
S
0
1
2
3
4
5
6
7
C
D
Instruction
AI03752D
31/55
Instructions
M25P16
6.11
Deep Power-down (DP)
Executing the Deep Power-down (DP) instruction is the only way to put the device in the
lowest consumption mode (the Deep Power-down mode). It can also be used as a software
protection mechanism, while the device is not in active use, as in this mode, the device
ignores all Write, Program and Erase instructions.
Driving Chip Select (S) High deselects the device, and puts the device in the Standby mode
(if there is no internal cycle currently in progress). But this mode is not the Deep Power-
down mode. The Deep Power-down mode can only be entered by executing the Deep
Power-down (DP) instruction, subsequently reducing the standby current (from I
to I
,
CC1
CC2
as specified in Table 14).
To take the device out of Deep Power-down mode, the Release from Deep Power-down and
Read Electronic Signature (RES) instruction must be issued. No other instruction must be
issued while the device is in Deep Power-down mode.
The Release from Deep Power-down and Read Electronic Signature (RES) instruction also
allows the electronic signature of the device to be output on Serial Data output (Q).
The Deep Power-down mode automatically stops at power-down, and the device always
powers up in the Standby mode.
The Deep Power-down (DP) instruction is entered by driving Chip Select (S) Low, followed
by the instruction code on Serial Data input (D). Chip Select (S) must be driven Low for the
entire duration of the sequence.
The instruction sequence is shown in Figure 18.
Chip Select (S) must be driven High after the eighth bit of the instruction code has been
latched in, otherwise the Deep Power-down (DP) instruction is not executed. As soon as
Chip Select (S) is driven High, it requires a delay of t before the supply current is reduced
DP
to I
and the Deep Power-down mode is entered.
CC2
Any Deep Power-down (DP) instruction, while an Erase, Program or Write cycle is in
progress, is rejected without having any effects on the cycle that is in progress.
Figure 18. Deep Power-down (DP) instruction sequence
S
t
DP
0
1
2
3
4
5
6
7
C
D
Instruction
Standby mode
Deep Power-down mode
AI03753D
32/55
M25P16
Instructions
6.12
Release from Deep Power-down and Read Electronic
Signature (RES)
To take the device out of Deep Power-down mode, the Release from Deep Power-down and
Read Electronic Signature (RES) instruction must be issued. No other instruction must be
issued while the device is in Deep Power-down mode.
The instruction can also be used to read, on Serial Data output (Q), the old-style 8-bit
electronic signature, whose value for the M25P16 is 14h.
Please note that this is not the same as, or even a subset of, the JEDEC 16-bit electronic
signature that is read by the Read Identifier (RDID) instruction. The old-style electronic
signature is supported for reasons of backward compatibility, only, and should not be used
for new designs. New designs should, instead, make use of the JEDEC 16-bit electronic
signature, and the Read Identifier (RDID) instruction.
Except while an Erase, Program or Write Status Register cycle is in progress, the Release
from Deep Power-down and Read Electronic Signature (RES) instruction always provides
access to the old-style 8-bit electronic signature of the device, and can be applied even if the
Deep Power-down mode has not been entered.
Any Release from Deep Power-down and Read Electronic Signature (RES) instruction while
an Erase, Program or Write Status Register cycle is in progress, is not decoded, and has no
effect on the cycle that is in progress.
The device is first selected by driving Chip Select (S) Low. The instruction code is followed
by 3 dummy bytes, each bit being latched-in on Serial Data input (D) during the rising edge
of Serial Clock (C). Then, the old-style 8-bit electronic signature, stored in the memory, is
shifted out on Serial Data output (Q), each bit being shifted out during the falling edge of
Serial Clock (C).
The instruction sequence is shown in Figure 19.
The Release from Deep Power-down and Read Electronic Signature (RES) instruction is
terminated by driving Chip Select (S) High after the electronic signature has been read at
least once. Sending additional clock cycles on Serial Clock (C), while Chip Select (S) is
driven Low, cause the electronic signature to be output repeatedly.
When Chip Select (S) is driven High, the device is put in the Standby Power mode. If the
device was not previously in the Deep Power-down mode, the transition to the Standby
Power mode is immediate. If the device was previously in the Deep Power-down mode,
though, the transition to the Standby Power mode is delayed by t
, and Chip Select (S)
RES2
must remain High for at least t
(max). Once in the Standby Power mode, the device
RES2
waits to be selected, so that it can receive, decode and execute instructions.
33/55
Instructions
M25P16
Figure 19. Release from Deep Power-down and Read Electronic Signature (RES) instruction
sequence and data-out sequence
S
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31 32 33 34 35 36 37 38
C
t
Instruction
3 Dummy bytes
RES2
23 22 21
MSB
3
2
1
0
D
Q
Electronic Signature Out
High Impedance
7
6
5
4
3
2
0
1
MSB
Deep Power-down mode
Standby mode
AI04047C
1. The value of the 8-bit electronic signature, for the M25P16, is 14h.
Figure 20. Release from Deep Power-down (RES) instruction sequence
S
t
RES1
0
1
2
3
4
5
6
7
C
D
Instruction
High Impedance
Q
Deep Power-down mode
Standby mode
AI04078B
Driving Chip Select (S) High after the 8-bit instruction byte has been received by the device, but before
the whole of the 8-bit electronic signature has been transmitted for the first time (as shown in Figure 20),
still ensures that the device is put into Standby Power mode. If the device was not previously in the Deep
Power-down mode, the transition to the Standby Power mode is immediate. If the device was previously
in the Deep Power-down mode, though, the transition to the Standby Power mode is delayed by t
,
RES1
and Chip Select (S) must remain High for at least t
(max). Once in the Standby Power mode, the
RES1
device waits to be selected, so that it can receive, decode and execute instructions.
34/55
M25P16
Power-up and power-down
7
Power-up and power-down
At power-up and power-down, the device must not be selected (that is Chip Select (S) must
follow the voltage applied on V ) until V reaches the correct value:
CC
CC
●
V
V
(min) at power-up, and then for a further delay of t
at power-down
CC
SS
VSL
●
A safe configuration is provided in Section 3: SPI modes.
To avoid data corruption and inadvertent write operations during power-up, a Power On
Reset (POR) circuit is included. The logic inside the device is held reset while V is less
CC
than the Power On Reset (POR) threshold voltage, V – all operations are disabled, and
WI
the device does not respond to any instruction.
Moreover, the device ignores all Write Enable (WREN), Page Program (PP), Sector Erase
(SE), Bulk Erase (BE) and Write Status Register (WRSR) instructions until a time delay of
t
has elapsed after the moment that V rises above the V threshold. However, the
PUW
CC WI
correct operation of the device is not guaranteed if, by this time, V is still below V (min).
CC
CC
No Write Status Register, Program or Erase instructions should be sent until the later of:
●
t
t
after V passed the V threshold
CC WI
PUW
VSL
●
after V passed the V (min) level.
CC
CC
These values are specified in Table 8.
If the delay, t
, has elapsed, after V has risen above V (min), the device can be
VSL
CC
CC
selected for READ instructions even if the t
delay is not yet fully elapsed.
PUW
At power-up, the device is in the following state:
●
●
●
The device is in the Standby mode (not the Deep Power-down mode)
The Write Enable Latch (WEL) bit is reset
The Write In Progress (WIP) bit is reset.
Normal precautions must be taken for supply rail decoupling, to stabilize the V supply.
CC
Each device in a system should have the V rail decoupled by a suitable capacitor close to
CC
the package pins (generally, this capacitor is of the order of 100 nF).
At power-down, when V drops from the operating voltage, to below the Power On Reset
CC
(POR) threshold voltage, V , all operations are disabled and the device does not respond
WI
to any instruction (the designer needs to be aware that if a power-down occurs while a
Write, Program or Erase cycle is in progress, some data corruption can result).
35/55
Initial delivery state
Figure 21. Power-up timing
M25P16
V
CC
V
(max)
CC
Program, Erase and Write commands are rejected by the device
Chip selection not allowed
V
(min)
CC
tVSL
Read access allowed
Device fully
accessible
Reset state
of the
device
V
WI
tPUW
time
AI04009C
Table 8.
Symbol
Power-up timing and V threshold
WI
Parameter
Min
Max
Unit
(1)
tVSL
VCC(min) to S Low
30
1
µs
ms
V
(1)
tPUW
Time delay to Write instruction
Write Inhibit voltage
10
(1)
VWI
1.5
2.5
1. These parameters are characterized only.
8
Initial delivery state
The device is delivered with the memory array erased: all bits are set to ‘1’ (each byte
contains FFh). The Status Register contains 00h (all Status Register bits are 0).
36/55
M25P16
Maximum rating
9
Maximum rating
Stressing the device above the rating listed in Table 9: Absolute maximum ratings may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability. Refer also to the Numonyx SURE Program
and other relevant quality documents.
Table 9.
Symbol
Absolute maximum ratings
Parameter
Min
Max
Unit
TSTG
TLEAD
VIO
Storage temperature
–65
150
°C
°C
V
Lead temperature during soldering
Input and output voltage (with respect to ground)
Supply voltage
see (1)
–0.6(2) VCC + 0.6(3)
VCC
–0.6
4.0
V
VESD
Electrostatic discharge voltage (Human Body model)(4)
–2000
2000
V
1. Compliant with JEDEC Std J-STD-020C (for small body, Sn-Pb or Pb assembly), the Numonyx
ECOPACK® 7191395 specification, and the European directive on Restrictions on Hazardous Substances
(RoHS) 2002/95/EU.
2. The minimum voltage may reach the value of -2 V for no more than 20 ns during transitions.
3. The maximum voltage may reach the value of VCC+2 V for no more than 20 ns during transitions.
4. JEDEC Std JESD22-A114A (C1 = 100 pF, R1 = 1500 Ω, R2 = 500 Ω).
37/55
DC and AC parameters
M25P16
10
DC and AC parameters
This section summarizes the operating and measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC characteristic tables that
follow are derived from tests performed under the measurement conditions summarized in
the relevant tables. Designers should check that the operating conditions in their circuit
match the measurement conditions when relying on the quoted parameters.
Table 10. Operating conditions
Symbol
Parameter
Min
Max
Unit
VCC
Supply voltage
Ambient operating temperature
2.7
–40
–40
3.6
125
85
V
grade 3
grade 6
°C
°C
TA
Table 11. Data retention and endurance
Parameter
Condition
Device grade 6
Min
Max
Unit
100 000
10 000
20
Erase/Program cycles
Data retention
Cycles per sector
years
Device grade 3
at 55 °C
Table 12. AC measurement conditions
Symbol
Parameter
Min
Max
Unit
CL
Load capacitance
30
pF
ns
V
Input rise and fall times
5
Input pulse voltages
0.2VCC to 0.8VCC
0.3VCC to 0.7VCC
Input timing reference voltages
Output timing reference voltages
V
V
CC / 2
V
Figure 22. AC measurement I/O waveform
Input levels
Input and output
timing reference levels
0.8V
CC
0.7V
CC
0.5V
CC
0.3V
CC
0.2V
CC
AI07455
(1)
Table 13. Capacitance
Symbol
Parameter
Test Condition
Min
Max
Unit
COUT
CIN
Output capacitance (Q)
VOUT = 0 V
VIN = 0 V
8
6
pF
pF
Input capacitance (other pins)
1. Sampled only, not 100% tested, at TA = 25 °C and a frequency of 20 MHz.
38/55
M25P16
DC and AC parameters
Table 14. DC characteristics
Test condition (in addition
Symbol
Parameter
Min
Max
Unit
to those in Table 10)
ILI
Input leakage current
Output leakage current
2
2
µA
µA
µA
µA
µA
µA
ILO
Grade 6
50
ICC1
Standby current
S = VCC, VIN = VSS or VCC
S = VCC, VIN = VSS or VCC
Grade 3
Grade 6
Grade 3
100
10
Deep Power-down
current
ICC2
100
C = 0.1VCC / 0.9.VCC at
75 MHz, Q = open
12
4
mA
mA
ICC3
Operating current (READ)
C = 0.1VCC / 0.9.VCC at
33 MHz, Q = open
ICC4
ICC5
ICC6
ICC7
VIL
Operating current (PP)
Operating current (WRSR)
Operating current (SE)
Operating current (BE)
Input low voltage
S = VCC
S = VCC
S = VCC
S = VCC
15
15
mA
mA
mA
mA
V
15
15
– 0.5
0.3VCC
VIH
Input high voltage
0.7VCC VCC+0.4
0.4
V
VOL
VOH
Output low voltage
IOL = 1.6 mA
V
Output high voltage
IOH = –100 µA
VCC–0.2
V
39/55
DC and AC parameters
Table 15.
M25P16
AC characteristics (grade 6, T9HX technology)
Applies only to products made with T9HX technology, identified with process digit ‘4’(1)
Test conditions specified in Table 10 and Table 12
Symbol Alt.
Parameter
Min
Typ(2)
Max Unit
Clock frequency for the following instructions:
fC
fC FAST_READ, PP, SE, BE, DP, RES, WREN,
WRDI, RDID, RDSR, WRSR
D.C.
75 MHz
fR
Clock frequency for READ instructions
tCLH Clock High time
D.C.
6
33 MHz
(3)
tCH
ns
ns
(2)
tCL
tCLL Clock Low time
6
(4)
(4)
tCLCH
tCHCL
Clock Rise time(5) (peak to peak)
Clock Fall time(5) (peak to peak)
0.1
0.1
5
V/ns
V/ns
ns
tSLCH tCSS S Active Setup time (relative to C)
tCHSL S Not Active Hold time (relative to C)
5
ns
tDVCH tDSU Data In Setup time
tCHDX tDH Data In Hold time
2
ns
5
ns
tCHSH
tSHCH
S Active Hold time (relative to C)
S Not Active Setup time (relative to C)
5
ns
5
ns
tSHSL tCSH S Deselect time
100
ns
(4)
tSHQZ
tDIS Output Disable time
8
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
tCLQV
tV Clock Low to Output Valid under 30 pF/10 pF
8/6
tCLQX tHO Output Hold time
0
5
5
5
5
tHLCH
tCHHH
tHHCH
tCHHL
HOLD Setup time (relative to C)
HOLD Hold time (relative to C)
HOLD Setup time (relative to C)
HOLD Hold time (relative to C)
tLZ HOLD to Output Low-Z
tHZ HOLD to Output High-Z
Write Protect Setup time
(4)
tHHQX
8
8
(4)
tHLQZ
tWHSL
tSHWL
(6)
(6)
20
Write Protect Hold time
100
(4)
tDP
S High to Deep Power-down mode
3
S High to Standby mode without Read
Electronic Signature
(4)
tRES1
30
µs
S High to Standby mode with Read Electronic
Signature
(4)
tRES2
tW
30
15
µs
Write Status Register cycle time
1.3
ms
40/55
M25P16
DC and AC parameters
AC characteristics (grade 6, T9HX technology) (continued)
Table 15.
Applies only to products made with T9HX technology, identified with process digit ‘4’(1)
Test conditions specified in Table 10 and Table 12
Symbol Alt.
Parameter
Min
Typ(2)
Max Unit
Page Program cycle time (256 bytes)
0.64
Page Program cycle time (n bytes, where n = 1
to 4)
0.01
(7)
tPP
5
ms
Page Program cycle time (n bytes, where n = 5
to 256)
int(n/8) × 0.02(8)
tSE
tBE
Sector Erase cycle time
Bulk Erase cycle time
0.6
13
3
s
s
40
1. Details of how to find the technology process in the marking are given in AN1995, see also Section 12:
Part numbering.
2. Typical values given for TA = 25 °C.
3. tCH + tCL must be greater than or equal to 1/ fC.
4. Value guaranteed by characterization, not 100% tested in production.
5. Expressed as a slew-rate.
6. Only applicable as a constraint for a WRSR instruction when SRWD is set at ‘1’.
7. When using the Page Program (PP) instruction to program consecutive bytes, optimized timings are
obtained with one sequence including all the bytes versus several sequences of only a few bytes (1 ≤n ≤
256).
8. int(A) corresponds to the upper integer part of A. For instance, int(12/8) = 2, int(32/8) = 4, int(15.3) =16.
41/55
DC and AC parameters
M25P16
(1)
Table 16. AC characteristics (25 MHz operation, grade 3)
Test conditions specified in Table 10 and Table 12
Symbol
Alt.
Parameter
Min
Typ
Max
Unit
Clock frequency for the following instructions:
FAST_READ, PP, SE, BE, DP, RES, WREN,
WRDI, RDSR, WRSR
fC
fR
fC
D.C.
25
20
MHz
Clock frequency for READ instructions
D.C.
18
18
0.1
0.1
10
10
5
MHz
ns
(2)
tCH
tCLH Clock High time
tCLL Clock Low time
(2)
tCL
ns
Clock Rise time(4) (peak to peak)
V/ns
V/ns
ns
(3)
tCLCH
(3)
tCHCL
Clock Fall time(4) (peak to peak)
tCSS S Active Setup time (relative to C)
S Not Active Hold time (relative to C)
tDSU Data In Setup time
tSLCH
tCHSL
tDVCH
tCHDX
tCHSH
tSHCH
tSHSL
ns
ns
tDH Data In Hold time
5
ns
S Active Hold time (relative to C)
S Not Active Setup time (relative to C)
tCSH S Deselect time
10
10
100
ns
ns
ns
(3)
tSHQZ
tDIS Output Disable time
15
15
ns
tCLQV
tCLQX
tHLCH
tCHHH
tHHCH
tCHHL
tV
tHO Output Hold time
HOLD Setup time (relative to C)
Clock Low to Output Valid
ns
0
ns
10
10
10
10
ns
HOLD Hold time (relative to C)
HOLD Setup time (relative to C)
HOLD Hold time (relative to C)
HOLD to Output Low-Z
ns
ns
ns
(3)
tHHQX
tLZ
15
20
ns
(3)
tHLQZ
tHZ
HOLD to Output High-Z
ns
(5)
tWHSL
Write Protect Setup time
20
ns
(5)
tSHWL
Write Protect Hold time
100
ns
(3)
tDP
S High to Deep Power-down mode
3
3
µs
S High to Standby mode without Electronic
Signature Read
(3)
tRES1
µs
S High to Standby mode with Electronic
Signature Read
(3)
tRES2
1.8
15
µs
(6)
tW
Write Status Register cycle time
Page Program cycle time (256 bytes)
Page Program cycle time (n bytes)
1.5
0.8
ms
(6)
tPP
5
ms
int(n/8) × 0.025(7)
42/55
M25P16
DC and AC parameters
(1)
Table 16. AC characteristics (25 MHz operation, grade 3) (continued)
Test conditions specified in Table 10 and Table 12
Symbol
Alt.
Parameter
Sector Erase cycle time
Bulk Erase cycle time
Min
Typ
Max
Unit
(6)
tSE
0.8
17
3
s
s
(6)
tBE
40
1. Preliminary data.
2. tCH + tCL must be greater than or equal to 1/ fC.
3. Value guaranteed by characterization, not 100% tested in production.
4. Expressed as a slew-rate.
5. Only applicable as a constraint for a WRSR instruction when SRWD is set at ‘1’.
6. Typical values given for TA = 85 °C.
7. int(A) corresponds to the upper integer part of A. For instance, int(12/8) = 2, int(32/8) = 4 int(15.3) =16.
Figure 23. Serial input timing
tSHSL
S
tCHSL
tSLCH
tCHSH
tSHCH
C
tDVCH
tCHCL
tCHDX
tCLCH
MSB IN
LSB IN
D
Q
High Impedance
AI01447C
43/55
DC and AC parameters
M25P16
Figure 24. Write Protect setup and hold timing during WRSR when SRWD = 1
W
tSHWL
tWHSL
S
C
D
High Impedance
Q
AI07439
Figure 25. Hold timing
S
tHLCH
tCHHL
tHLQZ
tHHCH
C
tCHHH
tHHQX
Q
D
HOLD
AI02032
44/55
M25P16
DC and AC parameters
Figure 26. Output timing
S
tCH
C
tCLQV
tCLQV
tCL
tSHQZ
tCLQX
tCLQX
LSB OUT
Q
D
tQLQH
tQHQL
ADDR.LSB IN
AI01449e
45/55
Package mechanical
M25P16
11
Package mechanical
In order to meet environmental requirements, Numonyx offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect. The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label.
Figure 27. VFQFPN8 (MLP8) 8-lead very thin fine pitch quad flat package no lead,
6 × 5 mm, package outline
A
D
aaa C A
R1
D1
B
E
E1
E2
A2
e
b
2x
0.10 C
B
D2
0.10 C
A
θ
L
ddd
C
A
A1 A3
70-ME
1. Drawing is not to scale.
2. The circle in the top view of the package indicates the position of pin 1.
46/55
M25P16
Package mechanical
Table 17. VFQFPN8 (MLP8) 8-lead very thin fine pitch quad flat package no lead,
6 × 5 mm, package mechanical data
millimeters
inches
Symbol
Typ
Min
Max
Typ
Min
Max
A
A1
A2
A3
b
0.85
0.80
0.00
1.00
0.05
0.033
0.031
0.000
0.039
0.002
0.65
0.20
0.40
6.00
5.75
3.40
5.00
4.75
4.00
1.27
0.10
0.60
0.026
0.008
0.016
0.236
0.226
0.134
0.197
0.187
0.157
0.050
0.004
0.024
0.35
3.20
0.48
3.60
0.014
0.126
0.019
0.142
D
D1
D2
E
E1
E2
e
3.80
–
4.30
–
0.150
–
0.169
–
R1
L
0.00
0.50
0.000
0.020
0.75
12°
0.029
12°
Θ
aaa
bbb
ddd
0.15
0.10
0.05
0.006
0.004
0.002
47/55
Package mechanical
M25P16
Figure 28. VDFPN8 (MLP8) 8-lead very thin dual flat package no lead, 8 × 6 mm,
package outline
D
E
E2
e
b
D2
A
L
K
L1
ddd
A1
VDFPN-02
1. Drawing is not to scale.
2. The circle in the top view of the package indicates the position of pin 1.
Table 18. VDFPN8 (MLP8) 8-lead very thin dual flat package no lead, 8 × 6 mm,
package mechanical data
millimeters
Min
inches
Min
Symbol
Typ
Max
Typ
Max
A
A1
b
0.85
1.00
0.05
0.48
0.033
0.039
0.002
0.019
0.00
0.35
0.000
0.014
0.40
8.00
5.16
0.016
0.315
0.203
D
(1)
D2
ddd
E
0.05
0.002
–
6.00
4.80
1.27
0.236
0.189
0.050
E2
e
–
–
–
K
0.82
0.45
0.032
0.018
L
0.50
0.60
0.15
0.020
0.024
0.006
L1
N
8
8
1. D2 Max should not exceed (D – K – 2 × L).
48/55
M25P16
Package mechanical
Figure 29. SO8N – 8 lead plastic small outline, 150 mils body width, package outline
h x 45˚
A2
A
c
ccc
b
e
0.25 mm
D
GAUGE PLANE
k
8
1
E1
E
L
A1
L1
SO-A
1. Drawing is not to scale.
Table 19. SO8N – 8 lead plastic small outline, 150 mils body width, package
mechanical data
millimeters
Min
inches
Min
Symbol
Typ
Max
Typ
Max
A
A1
A2
b
1.75
0.25
0.069
0.010
0.10
1.25
0.28
0.17
0.004
0.049
0.011
0.007
0.48
0.23
0.10
5.00
6.20
4.00
–
0.019
0.009
0.004
0.197
0.244
0.157
–
c
ccc
D
4.90
6.00
3.90
1.27
4.80
5.80
3.80
–
0.193
0.236
0.154
0.050
0.189
0.228
0.150
–
E
E1
e
h
0.25
0°
0.50
8°
0.010
0°
0.020
8°
k
L
0.40
1.27
0.016
0.050
L1
1.04
0.041
49/55
Package mechanical
M25P16
Figure 30. SO8W – 8 lead plastic small outline, 208 mils body width, package outline
A2
A
c
b
CP
e
D
N
1
E E1
A1
k
L
6L_ME
1. Drawing is not to scale.
Table 20. SO8 wide – 8 lead plastic small outline, 208 mils body width,
package mechanical data
millimeters
Min
inches
Min
Symbol
Typ
Max
Typ
Max
A
A1
A2
b
2.50
0.25
2.00
0.51
0.35
0.10
6.05
6.22
8.89
–
0.098
0.010
0.079
0.020
0.014
0.004
0.238
0.245
0.350
–
0.00
1.51
0.35
0.10
0.000
0.059
0.014
0.004
0.40
0.20
0.016
0.008
c
CP
D
E
5.02
7.62
–
0.198
0.300
–
E1
e
1.27
0.050
k
0°
10°
0°
10°
L
0.50
8
0.80
0.020
8
0.031
N
50/55
M25P16
Package mechanical
Figure 31. SO16 wide – 16-lead plastic small outline, 300 mils body width, package
outline
D
h x 45˚
16
9
C
E
H
1
8
θ
A2
A
A1
L
ddd
B
e
SO-H
1. Drawing is not to scale.
Table 21. SO16 wide – 16-lead plastic small outline, 300 mils body width,
mechanical data
millimeters
Min
inches
Min
Symbol
Typ
Max
Typ
Max
A
A1
B
2.35
0.10
0.33
0.23
10.10
7.40
–
2.65
0.30
0.51
0.32
10.50
7.60
–
0.093
0.004
0.013
0.009
0.398
0.291
–
0.104
0.012
0.020
0.013
0.413
0.299
–
C
D
E
e
1.27
0.050
H
10.00
0.25
0.40
0°
10.65
0.75
1.27
8°
0.394
0.010
0.016
0°
0.419
0.030
0.050
8°
h
L
θ
ddd
0.10
0.004
51/55
Part numbering
M25P16
12
Part numbering
Table 22. Ordering information scheme
Example:
M25P16
–
V ME 6
T
P
Device type
M25P = Serial Flash memory for code storage
Device function
16 = 16 Mbit (2 Mbit × 8)
Operating voltage
V = VCC = 2.7 V to 3.6 V
Package
MP = VFQFPN8 6 × 5 mm (MLP8)
ME = VDFPN8 8 × 6 mm (MLP8)(1)
MN = SO8N (150 mils width)
MW = SO8W (208 mils width)
MF = SO16 (300 mils width)
Device grade
6 = Industrial temperature range, –40 to 85 °C.
Device tested with standard test flow
3
(2) = Automotive temperature range, –40 to 125 °C.
Device tested with high reliability certified flow.
Option
blank = Standard packing
T = Tape and reel packing
Plating Technology
P or G = ECOPACK® (RoHS compliant)
1. Not for new design, please use VFQFPN8 6 × 5 mm.
2. Grade 3 is available only in devices delivered in SO8N packages.
Note:
For a list of available options (speed, package, etc.), for further information on any aspect of
this device or when ordering parts operating at 75 MHz (0.11 µm, process digit ‘4’), please
contact your nearest Numonyx Sales Office.
52/55
M25P16
Revision history
13
Revision history
Table 23. Document revision history
Date
Revision
Changes
Target Specification Document written
16-Jan-2002
0.1
Clarification of descriptions of entering Standby Power mode from Deep
Power-down mode, and of terminating an instruction sequence or data-
out sequence.
23-Apr-2002
0.4
0.5
ICC2(max) value changed to 10µA
Typical Page Program time improved. Write Protect setup and hold times
specified, for applications that switch Write Protect to exit the Hardware
Protection mode immediately before a WRSR, and to enter the Hardware
Protection mode again immediately after
13-Dec-2002
15-May-2003
0.6
0.7
0.8
MLP8 package added
50MHz operation, and RDID instruction added. Published internally, only
8x6 MLP8 and SO16(300 mil) packages added
20-Jun-2003
24-Sep-2003
tPP, tSE and tBE revised. SO16 package code changed. Output Timing
Reference Voltage changed. Document promoted to Preliminary Data.
1.0
2.0
3.0
Table of contents, warning about exposed paddle on MLP8, and Pb-free
options added.
24-Nov-2003
17-May-2004
Value of tVSL(min) and tBE(typ) changed. Change of naming for VDFPN8
packages. Document promoted to full Datasheet.
MLP8(5x6) package removed. Soldering temperature information
clarified for RoHS compliant devices. Device Grade clarified
Notes 1 and 2 removed from Table 22: Ordering information scheme.
Small text changes.
Read Identification (RDID), Deep Power-down (DP) and Release from
Deep Power-down and Read Electronic Signature (RES) instructions,
and Active Power, Standby Power and Deep Power-down modes
paragraph clarified.
01-Apr-2005
01-Aug-2005
20-Oct-2005
4.0
5.0
6.0
Updated Page Program (PP) instructions in Page programming, Page
Program (PP) and Table 15: AC characteristics (Grade 6).
VFQFPN8 package added (see Figure 27: VFQFPN8 (MLP8) 8-lead very
thin fine pitch quad flat package no lead, 6 × 5 mm, package outline and
Table 17: VFQFPN8 (MLP8) 8-lead very thin fine pitch quad flat package
no lead, 6 × 5 mm, package mechanical data).
All packages are ECOPACK®. “Blank” option removed under Plating
Technology.
SO8 Narrow and SO8 Wide packages added (see Section 11: Package
mechanical). VDFPN8 package updated (see Table 18: VDFPN8 (MLP8)
8-lead very thin dual flat package no lead, 8 × 6 mm, package
mechanical data). Note 1 added to Table 22: Ordering information
scheme.
27-Feb-2006
04-Jul-2006
7
8
Figure 4: Bus master and memory devices on the SPI bus updated and
Note 2 added. SO8N package specifications updated (see Figure 29 and
Table 19). Small text changes.
53/55
Revision history
Table 23. Document revision history (continued)
M25P16
Date
Revision
Changes
Page Program, Sector Erase and Bulk Erase updated in Features.
VIO max modified in Table 9: Absolute maximum ratings.
10-Oct-2006
9
Table 15: AC characteristics (grade 6, T9HX technology) added.
VFQFPN8 package specifications updated (see Table 17). Note 1 added
to Table 18. Note: on page 52 modified.
Small text changes. Hardware Write protection added to Features.
VCC supply voltage and VSS ground signal descriptions added. Figure 4:
Bus master and memory devices on the SPI bus modified, note 2
removed and replaced by an explanatory paragraph. Write In Progress bit
behavior specified at Power-up (see Section 7: Power-up and power-
down). TLEAD added to Table 9: Absolute maximum ratings. Grade 3
temperature range added.
09-Jan-2007
10
Table 11: Data retention and endurance and Table 16: AC characteristics
(25 MHz operation, grade 3) added.
SO8W and VFQFPN8 package specifications updated (see Section 11:
Package mechanical).
Eliminated the reference to the Deep Power-down mode and updated the
Read Identification instruction in Section 6.3: Read Identification (RDID).
Inserted UID and CFI content columns in Table 5: Read Identification
(RDID) data-out sequence.
Modified Data bytes for RDID instruction in Table 4: Instruction set.
Modified Q signal in Figure 10: Read Identification (RDID) instruction
sequence and data-out sequence.
15-Jun-2007
11
Modified Test condition and maximum values for ICC3 in Table 14: DC
characteristics.
Eliminated Table 15: AC characteristics (Grade 6).
Modified the maximum value for fC in Table 15: AC characteristics (grade
6, T9HX technology).
Removed ‘low voltage’ from the title. Changed the typical time for Bulk
Erase on page 1.
Section 6.3: Read Identification (RDID) updated.
Added note 2 and 3 to Table 9: Absolute maximum ratings.
31-Oct-2007
10-Dec-2007
12
13
Modified maximum value for tCLQV in Table 15: AC characteristics (grade
6, T9HX technology).
Applied Numonyx branding.
54/55
M25P16
Please Read Carefully:
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYX™ PRODUCTS. NO LICENSE, EXPRESS OR
IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT
AS PROVIDED IN NUMONYX'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NUMONYX ASSUMES NO LIABILITY
WHATSOEVER, AND NUMONYX DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF
NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,
MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
Numonyx products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility
applications.
Numonyx may make changes to specifications and product descriptions at any time, without notice.
Numonyx, B.V. may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the
presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied,
by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights.
Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Numonyx reserves
these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.
Contact your local Numonyx sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an order number and are referenced in this document, or other Numonyx literature may be obtained by
visiting Numonyx's website at http://www.numonyx.com.
Numonyx StrataFlash is a trademark or registered trademark of Numonyx or its subsidiaries in the United States and other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 11/5/7, Numonyx, B.V., All Rights Reserved.
55/55
相关型号：
©2020 ICPDF网 联系我们和版权申明