LV8572A [NSC]
LV8572A Low Voltage Real Time Clock (RTC); LV8572A低电压实时时钟( RTC )![LV8572A](http://pdffile.icpdf.com/pdf1/p00050/img/icpdf/LV8572A_260324_icpdf.jpg)
型号: | LV8572A |
厂家: | ![]() |
描述: | LV8572A Low Voltage Real Time Clock (RTC) |
文件: | 总20页 (文件大小:330K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
PRELIMINARY
December 1993
LV8572A Low Voltage Real Time Clock (RTC)
General Description
l
The LV8572A is intended for use in microprocessor based
systems where information is required for multi-tasking, data
logging or general time of day/date information. This device
is implemented in low voltage silicon gate microCMOS tech-
nology to provide low standby power in battery back-up en-
vironments. The circuit’s architecture is such that it looks
like a contiguous block of memory or I/O ports. The address
space is organized as 2 software selectable pages of 32
bytes. This includes the Control Registers, the Clock Coun-
ters, the Alarm Compare RAM, and the Time Save RAM.
Any of the RAM locations that are not being used for their
intended purpose may be used as general purpose CMOS
RAM.
fails may be logged into RAM automatically when V
BB
. Additionally, two supply pins are provided. When
V
V
CC
l
V
CC
, internal circuitry will automatically switch from
the main supply to the battery supply. Status bits are provid-
ed to indicate initial application of battery power, system
BB
power, and low battery detect.
(Continued)
Features
Y
g
3.3V 10% supply
Y
Full function real time clock/calendar
Ð 12/24 hour mode timekeeping
Ð Day of week and day of years counters
Ð Four selectable oscillator frequencies
Ð Parallel resonant oscillator
Time and date are maintained from 1/100 of a second to
year and leap year in a BCD format, 12 or 24 hour modes.
Day of week, day of month and day of year counters are
provided. Time is controlled by an on-chip crystal oscillator
requiring only the addition of the crystal and two capacitors.
The choice of crystal frequency is program selectable.
Y
Power fail features
Ð Internal power supply switch to external battery
Ð Power Supply Bus glitch protection
Ð Automatic log of time into RAM at power failure
On-chip interrupt structure
Ð Periodic, alarm, and power fail interrupts
Up to 44 bytes of CMOS RAM
Y
Y
Power failure logic and control functions have been integrat-
ed on chip. This logic is used by the RTC to issue a power
fail interrupt, and lock out the mp interface. The time power
Block Diagram
TL/F/11417–1
FIGURE 1
TRI-STATEÉ is a registered trademark of National Semiconductor Corporation.
C
1995 National Semiconductor Corporation
TL/F/11417
RRD-B30M105/Printed in U. S. A.
Absolute Maximum Ratings (Notes 1 & 2)
Specifications for the 883 version of this product are
listed separately.
Operation Conditions
Min
3.0
Max
3.6
Unit
V
Supply Voltage (V ) (Note 3)
CC
b
a
0.5V to 7.0V
b
Supply Voltage (V
)
CC
Supply Voltage (V ) (Note 3)
BB
2.2
V
CC
0.4
V
b
a
DC Input Voltage (V
)
0.5V to V
0.5V
0.5V
DC Input or Output Voltage
)
IN
CC
0.0
V
CC
V
(V , V
b
a
IN OUT
DC Output Voltage (V
)
0.5V to V
OUT
CC
b
a
85
Operation Temperature (T )
A
40
C
§
kV
b
a
65 C to 150 C
Storage Temperature Range
Power Dissipation (PD)
§
§
500 mW
Electr-Static Discharge Rating
Typical Values
1
Lead Temperature (Soldering, 10 sec.)
260 C
§
i
DIP
Board
Socket
Board
Socket
61 C/W
§
JA
67 C/W
§
i
PLCC
80 C/W
§
JA
88 C/W
§
DC Electrical Characteristics
V
l
e
e
e
g
3.3V 10%, V
V
CC
2.5V, V
, C
IH L
100 pF (unless otherwise specified)
Conditions Min
BB
PFAIL
Symbol
Parameter
Max
Units
a
CC
V
V
V
V
High Level Input Voltage
(Note 4)
Any Inputs Except OSC IN,
OSC IN with External Clock
2.0
b
V
0.3
V
V
IH
V
0.2
BB
b
b
Low Level Input Voltage
All Inputs Except OSC IN
OSC IN with External Clock
0.3
0.3
0.8
0.2
V
V
IL
e b
e b
b
0,2
High Level Output Voltage
(Excluding OSC OUT, INTR)
I
I
20 mA
2.0 mA
V
V
V
OH
OL
OUT
OUT
CC
2.4
e
e
Low Level Output Voltage
(Excluding OSC OUT)
I
I
20 mA
2.0 mA
0.2
0.3
V
V
OUT
OUT
e
g
I
I
I
Input Current (Except OSC IN)
V
V
V
V
or GND
0.7
mA
mA
IN
IN
CC
e
e
g
g
Output TRI-STATE Current
É
Output High Leakage Current
MFO, INTR Pins
V
or GND
or GND
1
1
OZ
OUT
CC
V
CC
LKG
OUT
mA
Outputs Open Drain
e
V
V
I
Quiescent Supply Current
(Note 7)
F
32.768 kHz
CC
OSC
e
e
e
V
V
V
or GND (Note 5)
or GND (Note 6)
220
700
5
mA
mA
mA
IN
IN
IN
CC
CC
V
IH
or V (Note 6)
IL
e
F
4.194304 MHz or
4.9152 MHz
or GND (Note 6)
OSC
e
e
V
V
V
V
4
6
mA
mA
IN
IN
CC
or V (Note 6)
IH
IL
e
GND
I
I
Quiescent Supply Current
(Single Supply Mode)
(Note 7)
V
V
F
F
CC
BB
BB
IN
e
V
e
e
or GND
32.768 kHz
4.9152 MHz or
4.194304 MHz
CC
30
3
mA
mA
OSC
OSC
e
GND
Standby Mode Battery
Supply Current
(Note 7)
V
CC
OSC OUT
other pins
e
e
open circuit,
GND
e
e
F
OSC
F
OSC
32.768 kHzmA
4.9152 MHz or
4.194304 MHz
8
400
mA
mA
s
s
2.6V
other pins at GND
I
Battery Leakage
2.2V
V
BLK
BB
e
e
e
e
V
CC
V
CC
GND, V
3.6V, V
2.6V
2.2V
0.8
mA
mA
BB
BB
b
0.8
Note 1: Absolute Maximum Ratings are those values beyond which damage to the device may occur.
Note 2: Unless otherwise specified all voltages are referenced to ground.
s
e
e
b
0.4V.
CC
Note 3: For F
4.194304 or 4.9152 MHz, V minimum
BB
2.8V. In battery backed mode, V
V
OSC
BB
Single Supply Mode: Data retention voltage is 2.2V min.
In single Supply Mode (Power connected to V pin) 3.0V
s
s
3.6.
V
CC
CC
Note 4: This parameter (V ) is not tested on all pins at the same time.
IH
Note 5: This specification tests I
with all power fail circuitry disabled, by setting D7 of Interrupt Control Register 1 to 0.
with all power fail circuitry enabled, by setting D7 of Interrupt Control Register 1 to 1.
CC
CC
Note 6: This specification tests I
e
Note 7: OSC IN is driven by a signal generator. Contents of the Test Register
00(H) and the MFO pin is not configured as buffered oscillator out.
2
AC Electrical Characteristics
l
e
e
e
, C 100 pF (unless otherwise specified)
IH L
g
V
3.3V 10%, V
2.5V, V
V
CC
Symbol
READ TIMING
BB
PFAIL
Parameter
Min
Max
Units
t
t
t
t
t
t
t
t
Address Valid Prior to Read Strobe
Read Strobe Width (Note 8)
10
ns
ns
ns
ns
ns
ns
ns
ns
AR
100
RW
CD
Chip Select to Data Valid Time
Address Hold after Read (Note 9)
Read Strobe to Valid Data
100
2
RAH
RD
90
80
Read or Chip Select to TRI-STATE
DZ
Chip Select Hold after Read Strobe (Note 9)
0
RCH
DS
Minimum Inactive Time between Read or Write Accesses
70
WRITE TIMING
t
t
t
t
t
t
t
Address Valid before Write Strobe
Address Hold after Write Strobe (Note 9)
Chip Select to End of Write Strobe
Write Strobe Width (Note 10)
10
2
ns
ns
ns
ns
ns
ns
ns
AW
WAH
CW
110
100
70
2
WW
DW
Data Valid to End of Write Strobe
Data Hold after Write Strobe (Note 9)
Chip Select Hold after Write Strobe (Note 9)
WDH
WCH
0
INTERRUPT TIMING
t
Clock Rollover to INTR Out is Typically 20 ms
ROLL
Note 8: Read Strobe width as used in the read timing table is defined as the period when both chip select and read inputs are low. Hence read commences when
both signals are low and terminates when either signal returns high.
Note 9: Hold time is guaranteed by design but not production tested. This limit is not used to calculate outgoing quality levels.
Note 10: Write Strobe width as used in the write timing table is defined as the period when both chip select and write inputs are low. Hence write commences when
both signals are low and terminates when either signal returns high.
AC Test Conditions
Input Pulse Levels
Input Rise and Fall Times
Input and Output
Reference Levels
TRI-STATE Reference
Levels (Note 12)
GND to 3.0V
6 ns (10%–90%)
1.3V
a
Active High 0.5V
b
Active Low 0.5V
e
Note 11: C
100 pF, includes jig and scope capacitance.
L
e
e
e
Note 12: S1
V
for active low to high impedance measurements.
CC
S1
S1
GND for active high to high impedance measurements.
open for all other timing measurements.
e
e
1 MHz)
Capacitance (T
25 C, f
§
A
TL/F/11417–2
Parameter
(Note 13)
Symbol
Typ
Units
C
C
Input Capacitance
5
7
pF
pF
IN
Output Capacitance
OUT
Note 13: This parameter is not 100% tested.
Note 14: Output rise and fall times 25 ns max (10%–90%) with 100 pF load.
3
Timing Waveforms
Read Timing Diagram
TL/F/11417–3
Write Timing Diagram
TL/F/11417–4
4
V
: This is the main system power pin.
CC
General Description (Continued)
GND: This is the common ground power pin for both V
.
BB
The LV8572A’s interrupt structure provides three basic
types of interrupts: Periodic, Alarm/Compare, and Power
Fail. Interrupt mask and status registers enable the masking
and easy determination of each interrupt.
and V
CC
Connection Diagrams
In-Line Packages
Pin Description
CS, RD, WR (Inputs): These pins interface to mP control
lines. The CS pin is an active low enable for the read and
write operations. Read and Write pins are also active low
and enable reading or writing to the RTC. All three pins are
disabled when power failure is detected. However, if a read
or write is in progress at this time, it will be allowed to com-
plete its cycle.
A0–A4 (Inputs): These 5 pins are for register selection.
They individually control which location is to be accessed.
These inputs are disabled when power failure is detected.
OSC IN (Input): OSC OUT (Output): These two pins are
used to connect the crystal to the internal parallel resonant
oscillator. The oscillator is always running when power is
applied to V and V , and the correct crystal select bits in
BB CC
the Real Time Mode Register have been set.
MFO (Output): The multi-function output can be used as a
second interrupt output for interrupting the mP. This pin can
also provide an output for the oscillator. The MFO output is
configured as push-pull, active high for normal or single
power supply operation and as an open drain during stand-
TL/F/11417–5
Top View
DIP: Order Number LV8572AN
See NS Package Number N24C
l
by mode (V
V ). If in battery backed mode and a pull-
CC
BB
up resistor is attached, it should be connected to a voltage
no greater than V
SOIC: Order Number LV8572AM
See NS Package Number M24B
.
BB
INTR (Output): The interrupt output is used to interrupt the
processor when a timing event or power fail has occurred
and the respective interrupt has been enabled. The INTR
output is permanently configured active low, open drain. If in
battery backed mode and a pull-up resistor is attached, it
Plastic Chip Carrier
should be connected to a voltage no greater than V
.
BB
D0–D7 (Input/Output): These 8 bidirectional pins connect
to the host mP’s data bus and are used to read from and
write to the RTC. When the PFAIL pin goes low and a write
is not in progress, these pins are at TRI-STATE.
PFAIL (Input): In battery backed mode, this pin can have a
digital signal applied to it via some external power detection
e
logic. When PFAIL
logic 0 the RTC goes into a lockout
mode, in a minimum of 30 ms or a maximum of 63 ms unless
lockout delay is programmed. In the single power supply
mode, this pin is not useable as an input and should be tied
to V . Refer to section on Power Fail Functional Descrip-
CC
tion.
V
(Battery Power Pin): This pin is connected to a back-
BB
up power supply. This power supply is switched to the inter-
nal circuitry when the V becomes lower than V . Utiliz-
CC BB
ing this pin eliminates the need for external logic to switch in
and out the back-up power supply. If this feature is not to be
used then this pin must be tied to ground, the RTC pro-
grammed for single power supply only, and power applied to
TL/F/11417–6
Top View
Order Number LV8572AV
See NS Package Number V28A
the V
pin.
CC
5
Functional Description
The LV8572A contains a fast access real time clock, inter-
rupt control logic, power fail detect logic, and CMOS RAM.
All functions of the RTC are controlled by a set of seven
registers. A simplified block diagram that shows the major
functional blocks is given in Figure 1.
The memory map of the RTC is shown in the memory ad-
dressing table. The memory map consists of two 31 byte
pages with a main status register that is common to both
pages. A control bit in the Main Status Register is used to
select either page. Figure
2 shows the basic concept.
Page 0 contains all the clock timer functions, while page 1
has scratch pad RAM. The control registers are split into
two separate blocks to allow page 1 to be used entirely as
scratch pad RAM. Again a control bit in the Main Status
Register is used to select either control register block.
The blocks are described in the following sections:
1. Real Time Clock
2. Oscillator Prescaler
3. Interrupt Logic
4. Power Failure Logic
5. Additional Supply Management
TL/F/11417–7
FIGURE 2. LV8572A Internal Memory Map
6
Functional Description (Continued)
INITIAL POWER-ON of BOTH V and V
BB CC
Save Enable bit (D7) of the Time Save Control Register, and
then to write a zero. Writing a one into this bit will enable the
clock contents to be duplicated in the Time Save RAM.
Changing the bit from a one to a zero will freeze and store
the contents of the clock in Time Save RAM. The time then
can be read without concern for clock rollover, since inter-
nal logic takes care of synchronization of the clock. Be-
cause only the bits used by the clock counters will be
latched, the Time Save RAM should be cleared prior to use
to ensure that random data stored in the unused bits do not
confuse the host microprocessor. This bit can also provide
time save at power failure, see the Additional Supply Man-
agement Functions section. With the Time Save Enable bit
at a logical 0, the Time Save RAM may be used as RAM if
the latched read function is not necessary.
V
and V
may be applied in any sequence. In order for
CC
BB
the power fail circuitry to function correctly, whenever power
is off, the V pin must see a path to ground through a
CC
maximum of 1 MX. The user should be aware that the con-
trol registers will contain random data. The first task to be
carried out in an initialization routine is to start the oscillator
by writing to the crystal select bits in the Real Time Mode
Register. If the LV8572A is configured for single supply
mode, an extra 50 mA may be consumed until the crystal
select bits are programmed. The user should also ensure
that the RTC is not in test mode (see register descriptions).
REAL TIME CLOCK FUNCTIONAL DESCRIPTION
As shown in Figure 2, the clock has 10 bytes of counters,
which count from 1/100 of a second to years. Each counter
counts in BCD and is synchronously clocked. The count se-
quence of the individual byte counters within the clock is
shown later in Table VII. Note that the day of week, day of
month, day of year, and month counters all roll over to 1.
The hours counter in 12 hour mode rolls over to 1 and the
AM/PM bit toggles when the hours rolls over to 12
INITIALIZING AND WRITING TO THE
CALENDAR-CLOCK
Upon initial application of power to the RTC or when making
time corrections, the time must be written into the clock. To
correctly write the time to the counters, the clock would
normally be stopped by writing the Start/Stop bit in the Real
Time Mode Register to a zero. This stops the clock from
counting and disables the carry circuitry. When initializing
the clock’s Real Time Mode Register, it is recommended
that first the various mode bits be written while maintaining
the Start/Stop bit reset, and then writing to the register a
second time with the Start/Stop bit set.
e
counter.
e
1). The AM/PM bit is bit D7 in the hours
(AM
0, PM
All other counters roll over to 0. Also note that the day of
year counter is 12 bits long and occupies two addresses.
Upon initial application of power the counters will contain
random information.
The above method is useful when the entire clock is being
corrected. If one location is being updated the clock need
not be stopped since this will reset the prescaler, and time
will be lost. An ideal example of this is correcting the hours
for daylight savings time. To write to the clock ‘‘on the fly’’
the best method is to wait for the 1/100 of a second period-
ic interrupt. Then wait an additional 16 ms, and then write
the data to the clock.
READING THE CLOCK: VALIDATED READ
Since clocking of the counter occurs asynchronously to
reading of the counter, it is possible to read the counter
while it is being incremented (rollover). This may result in an
incorrect time reading. Thus to ensure a correct reading of
the entire contents of the clock (or that part of interest), it
must be read without a clock rollover occurring. In general
this can be done by checking a rollover bit. On this chip the
periodic interrupt status bits can serve this function. The
following program steps can be used to accomplish this.
PRESCALER/OSCILLATOR FUNCTIONAL
DESCRIPTION
Feeding the counter chain is a programmable prescaler
which divides the crystal oscillator frequency to 32 kHz and
further to 100 Hz for the counter chain (see Figure 3 ). The
crystal frequency that can be selected are: 32 kHz, 32.768
kHz, 4.9152 MHz, and 4.194304 MHz.
1. Initialize program for reading clock.
2. Dummy read of periodic status bit to clear it.
3. Read counter bytes and store.
4. Read rollover bit, and test it.
5. If rollover occured go to 3.
6. If no rollover, done.
To detect the rollover, individual periodic status bits can be
polled. The periodic bit chosen should be equal to the high-
est frequency counter register to be read. That is if only
SECONDS through HOURS counters are read, then the
SECONDS periodic bit should be used.
READING THE CLOCK: INTERRUPT DRIVEN
Enabling the periodic interrupt mask bits cause interrupts
just as the clock rolls over. Enabling the desired update rate
and providing an interrupt service routine that executes in
less than 10 ms enables clock reading without checking for
a rollover.
TL/F/11417–8
FIGURE 3. Programmable Clock Prescaler Block
READING THE CLOCK: LATCHED READ
Another method to read the clock that does not require
checking the rollover bit is to write a one into the Time
7
Functional Description (Continued)
The oscillator is programmed via the Real Time Mode Reg-
ister to operate at various frequencies. The crystal oscillator
is designed to offer optimum performance at each frequen-
cy. Thus, at 32.768 kHz the oscillator is configured as a low
frequency and low power oscillator. At the higher frequen-
cies the oscillator inverter is reconfigured. In addition to the
inverter, the oscillator feedback bias resistor is included on
chip, as shown in Figure 4. The oscillator input may be driv-
en from an external source if desired. Refer to test mode
application note for details. The oscillator stability is en-
hanced through the use of an on chip regulated power sup-
ply.
INTERRUPT LOGIC FUNCTIONAL DESCRIPTION
The RTC has the ability to coordinate processor timing ac-
tivities. To enhance this, an interrupt structure has been im-
plemented which enables several types of events to cause
interrupts. Interrupts are controlled via two Control Regis-
ters in block 1 and two Status Registers in block 0. (See
Register Description for notes on paging and also Figure 5
and Table I.)
The interrupts are enabled by writing a one to the appropri-
ate bits in Interrupt Control Register 0 and/or 1.
TABLE I. Registers that are
Applicable to Interrupt Control
The typical range of trimmer capacitor (as shown in Oscilla-
tor Circuit DiagramFigure 4, and in the typical application) at
the oscillator input pin is suggested only to allow accurate
tuning of the oscillator. This range is based on a typical
printed circuit board layout and may have to be changed
depending on the parasitic capacitance of the printed circuit
board or fixture being used. In all cases, the load capaci-
tance specified by the crystal manufacturer (nominal value
11 pF for the 32.768 crystal) is what determines proper os-
cillation. This load capcitance is the series combination of
capacitance on each side of the crystal (with respect to
ground).
Register
Select
Page
Register Name
Address
Select
Main Status Register
Periodic Flag Register
Interrupt Control
Register 0
X
0
X
0
00H
03H
1
1
1
0
0
0
03H
04H
02H
Interrupt Control
Register 1
Output Mode
Register
The Interrupt Status Flag D0, in the Main Status Register,
indicates the state of INTR and MFO outputs. It is set when
either output becomes active and is cleared when all RTC
interrupts have been cleared and no further interrupts are
pending (i.e., both INTR and MFO are returned to their inac-
tive state). This flag enables the RTC to be rapidly polled by
the mP to determine the source of an interrupt in a wiredÐ
OR interrupt system. (The Interrupt Status Flag provides a
true reflection of all conditions routed to the external pins.)
Status for the interrupts are provided by the Main Status
Register and the Periodic Flag Register. Bits D1–D5 of the
Main Status Register are the main interrupt bits.
These register bits will be set when their associated timing
events occur. Enabled Alarm comparisons that occur will
set its Main Status Register bit to a one. However, an exter-
nal interrupt will only be generated if the Alarm interrupt
enable bit is set (see Figure 5 ).
Disabling the periodic interrupts will mask the Main Status
Register periodic bit, but not the Periodic Flag Register bits.
The Power Fail Interrupt bit is set when the interrupt is en-
abled and a power fail event has occurred, and is not reset
until the power is restored. If all interrupt enable bits are 0
no interrupt will be asserted. However, status still can be
read from the Main Status Register in a polled fashion (see
Figure 5 ).
TL/F/11417–9
FIGURE 4. Oscillator Circuit Diagram
R
OUT
XTAL
C
o
C
t
(Switched
Internally)
To clear a flag in bits D2 and D3 of the Main Status Register
a 1 must be written back into the bit location that is to be
cleared. For the Periodic Flag Register reading the status
will reset all the periodic flags.
32/32.768 kHz 47 pF 2 pF–22 pF 150 kX to 350 kX
4.194304 MHz 68 pF 0 pF–80 pF 500X to 900X
4.9152 MHz
68 pF 29 pF–49 pF 500X to 900X
8
Functional Description (Continued)
Interrupts Fall Into Three Categories:
Figure 5. These flags constantly sense the periodic signals
and may be used whether or not interrupts are enabled.
These flags are cleared by any read or write operation per-
formed on this register.
1. The Alarm Compare Interrupt: Issued when the value in
the time compared RAM equals the counter.
2. The Periodic Interrupts: These are issued at every incre-
ment of the specific clock counter signal. Thus, an inter-
rupt is issued every minute, second, etc. Each of these
interrupts occurs at the roll-over of the specific counter.
To generate periodic interrupts at the desired rate, the asso-
ciated Periodic Interrupt Enable bit in Interrupt Control Reg-
ister 0 must be set. Any combination of periodic interrupts
may be enabled to operate simultaneously. Enabled period-
ic interrupts will now affect the Periodic Interrupt Flag in the
Main Status Register.
3. The Power Fail Interrupt: Issued upon recognition of a
power fail condition by the internal sensing logic. The
power failed condition is determined by the signal on the
PFAIL pin. The internal power fail signal is gated with the
chip select signal to ensure that the power fail interrupt
does not lock the chip out during a read or write.
When a periodic event occurs, the Periodic Interrupt Flag in
the Main Status Register is set, causing an interrupt to be
generated. The mP clears both flag and interrupt by writing a
‘‘1’’ to the Periodic Interrupt Flag. The individual flags in the
periodic Interrupt Flag Register do not require clearing to
cancel the interrupt.
ALARM COMPARE INTERRUPT DESCRIPTON
The alarm/time comparison interrupt is a special interrupt
similar to an alarm clock wake up buzzer. This interrupt is
generated when the clock time is equal to a value pro-
grammed into the alarm compare registers. Up to six bytes
can be enabled to perform alarm time comparisons on the
counter chain. These six bytes, or some subset thereof,
would be loaded with the future time at which the interrupt
will occur. Next, the appropriate bits in the Interrupt Control
Register 1 are enabled or disabled (refer to detailed descrip-
tion of Interrupt Control Register 1). The RTC then com-
pares these bytes with the clock time. When all the enabled
compare registers equal the clock time an alarm interrupt is
issued, but only if the alarm compare interrupt is enabled
can the interrupt be generated externally. Each alarm com-
pare bit in the Control Register will enable a specific byte for
comparison to the clock. Disabling a compare byte is the
same as setting its associated counter comparator to an
‘‘always equal’’ state. For example, to generate an interrupt
at 3:15 AM of every day, load the hours compare with 0 3
(BCD), the minutes compare with 1 5 (BCD) and the faster
counters with 0 0 (BCD), and then disable all other compare
registers. So every day when the time rolls over from
3:14:59.99, an interrupt is issued. This bit may be reset by
writing a one to bit D3 in the Main Status Register at any
time after the alarm has been generated.
If all periodic interrupts are disabled and a periodic interrupt
is left pending (i.e., the Periodic Interrupt Flag is still set), the
Periodic Interrupt Flag will still be required to be cleared to
cancel the pending interrupt.
POWER FAIL INTERRUPTS DESCRIPTION
The Power Fail Status Flag in the Main Status Register
monitors the state of the internal power fail signal. This flag
may be interrogated by the mP, but it cannot be cleared; it is
cleared automatically by the RTC when system power is
restored. To generate an interrupt when the power fails, the
Power Fail Interrupt Enable bit in Interrupt Control Register
1 is set. Although this interrupt may not be cleared, it may
be masked by clearing the Power Fail Interrupt Enable bit.
POWER FAILURE CIRCUITRY FUNCTIONAL
DESCRIPTION
Since the clock must be operated from a battery when the
main system supply has been turned off, the LV8572A pro-
vides circuitry to simplify design in battery backed systems.
This switches over to the back up supply, and isolates itself
from the host system. Figure 6 shows a simplified block
diagram of this circuitry, which consists of three major sec-
tions; 1) power loss logic: 2) battery switch over logic: and 3)
isolation logic.
If time comparison for an individual byte counter is disabled,
that corresponding RAM location can then be used as gen-
eral purpose storage.
Detection of power loss occurs when PFAIL is low. De-
bounce logic provides a 30 ms–63 ms debounce time, which
will prevent noise on the PFAIL pin from being interpreted
as a system failure. After 30 ms–63 ms the debounce logic
times out and a signal is generated indicating that system
power is marginal and is failing. The Power Fail Interrupt will
then be generated.
PERIODIC INTERRUPTS DESCRIPTION
The Periodic Flag Register contains six flags which are set
by real-time generated ‘‘ticks’’ at various time intervals, see
9
Functional Description (Continued)
10
Functional Description (Continued)
TL/F/11417–11
FIGURE 6. System-Battery Switchover (Upper Left), Power Fail
and Lock-Out Circuits (Lower Right)
If chip select is low when a power failure is detected, a
safety circuit will ensure that if a read or write is held active
continuously for greater than 30 ms after the power fail sig-
nal is asserted, the lock-out will be forced. If a lock-out delay
is enabled, the LV8572A will remain active for 480 ms after
power fail is detected. This will enable the mP to perform
last minute bookkeeping before total system collapse.
When the host CPU is finished accessing the RTC it may
force the bus lock-out before 480 ms has elapsed by reset-
ting the delay enable bit.
resistor should be connected to a voltage no greater than
.
V
BB
TABLE II. Pin Isolation during a Power Failure
e
PFAIL
Standby Mode
Pin
l
V
CC
Logic 0
V
BB
CS, RD, WR
A0–A4
Locked Out
Locked Out
Locked Out
Not Isolated
Not Isolated
Not Isolated
Locked Out
Locked Out
Locked Out
Not Isolated
Not Isolated
Open Drain
D0–D7
The battery switch over circuitry is completely independent
of the PFAIL pin. A separate circuit compares V to the
voltage. As the main supply fails, the RTC will continue
Oscillator
PFAIL
CC
V
BB
to operate from the V
INTR, MFO
pin until V
falls below the V
BB
CC
CC
voltage. At this time, the battery supply is switched in, V is
CC
disconnected, and the device is now in the standby mode. If
indeterminate operation of the battery switch over circuit is
The Interrupt Power Fail Operation bit in the Real-Time
Mode Register determine whether or not the interrupts will
continue to function after a power fail event.
to be avoided, then the voltage at the V
pin must not be
CC
allowed to equal the voltage at the V pin.
As power returns to the system, the battery switch over cir-
power as soon as it becomes
BB
a lock-out signal, and eventual
cuit will switch back to V
CC
greater than the battery voltage. The chip will remain in the
After the generation of
switch in of the battery supply, the pins of the RTC will be
configured as shown in Table II. Outputs that have a pull-up
e
e
0. When PFAIL 1
locked out state as long as PFAIL
11
Functional Description (Continued)
the chip is unlocked, but only after another 30 ms min
63 ms max debounce time. The system designer must en-
sure that his system is stable when power has returned.
x
This complete address space is organized into two pages.
Page 0 contains two blocks of control registers, timers, real
time clock counters, and special purpose RAM, while page
1 contains general purpose RAM. Using two blocks enables
the 9 control registers to be mapped into 5 locations. The
only register that does not get switched is the Main Status
Register. It contains the page select bit and the register
select bit as well as status information.
The power fail circuitry contains active linear circuitry that
draws supply current from V . In some cases this may be
CC
undesirable, so this circuit can be disabled by masking the
power fail interrupt. The power fail input can perform all
lock-out functions previously mentioned, except that no ex-
ternal interrupt will be issued. Note that the linear power fail
A memory map is shown in Figure 2 and register addressing
in Table III. They show the name, address and page loca-
tions for the LV8572A.
circuitry is switched off automatically when using V
standby mode.
in
BB
LOW BATTERY, INITIAL POWER ON DETECT, AND
POWER FAIL TIME SAVE
TABLE III. Register/Counter/RAM
Addressing for LV8572A
There are three other functions provided on the LV8572A to
ease power supply control. These are an initial Power On
detect circuit, which also can be used as a time keeping
failure detect, a low battery detect circuit, and a time save
on power failure.
PS
RS
A0-4
Description
(Note 1) (Note 2)
CONTROL REGISTERS
00
03
04
01
02
03
04
X
0
0
0
0
0
0
X
0
0
1
1
1
1
Main Status Register
Periodic Flag Register
On initial power up the Oscillator Fail Flag will be set to a
one and the real time clock start bit reset to a zero. This
indicates that an oscillator fail event has occurred, and time
keeping has failed.
Time Save Control Register
Real Time Mode Register
Output Mode Register
Interrupt Control Register 0
Interrupt Control Register 1
The Oscillator Fail flag will not be reset until the real-time
clock is started. This allows the system to discriminate be-
tween an initial power-up and recovery from a power failure.
If the battery backed mode is selected, then bit D6 of the
Periodic Flag Register must be written low. This will not af-
fect the contents of the Oscillator Fail Flag.
COUNTERS (CLOCK CALENDAR)
05
06
07
08
09
0
0
0
0
0
X
X
X
X
X
1/100, 1/10 Seconds (0–99)
Seconds
Minutes
Hours
(0–59)
(0–59)
(1–12, 0–23)
Days of
Month
Another status bit is the low battery detect. This bit is set
only when the clock is operating under the V
(1–28/29/30/31)
(1–12)
(0–99)
0A
0B
0C
0D
0E
0
0
0
0
0
X
X
X
X
X
Months
Years
pin, and
CC
when the battery voltage is determined to be less than 2.1V
(typical). When the power fail interrupt enable bit is low, it
disables the power fail circuit and will also shut off the low
battery voltage detection circuit as well.
Julian Date (LSB)
Julian Date
Day of Week
(1–99)
(0–3)
(1–7)
TIME COMPARE RAM
To relieve CPU overhead for saving time upon power failure,
the Time Save Enable bit is provided to do this automatical-
ly. (See also Reading the Clock: Latched Read.) The Time
Save Enable bit, when set, causes the Time Save RAM to
follow the contents of the clock. This bit can be reset by
software, but if set before a power failure occurs, it will auto-
matically be reset when the clock switches to the battery
supply (not when a power failure is detected by the PFAIL
pin). Thus, writing a one to the Time Save bit enables both a
software write or power fail write.
13
14
15
0
0
0
X
X
X
Sec Compare RAM (0–59)
Min Compare RAM (0–59)
Hours Compare
RAM
DOM Compare
RAM
(1–12, 0–23)
(1–28/29/30/31)
(1–12)
16
17
18
0
0
0
X
X
X
Months Compare
RAM
DOW Compare RAM (1–7)
TIME SAVE RAM
19
1A
1B
1C
1D
0
0
0
0
0
X
X
X
X
X
Seconds Time Save RAM
Minutes Time Save RAM
Hours Time Save RAM
SINGLE POWER SUPPLY APPLICATIONS
The LV8572A can be used in a single power supply applica-
pin must be connected to
tion. To achieve this, the V
BB
ground, and the power connected to V
Day of Month Time Save RAM
Months Time Save RAM
and PFAIL pins.
CC
The Oscillator Failed/Single Supply bit in the Periodic Flag
Register should be set to a logic 1, which will disable the
oscillator battery reference circuit. The power fail interrupt
should also be disabled. This will turn off the linear power
fail detection circuits, and will eliminate any quiescent power
drawn through these circuits. Until the crystal select bits are
initialized, the LV8572A may consume about 50 mA due to
arbitrary oscillator selection at power on.
1E
1F
0
0
1
RAM
RAM/Test Mode Register
X
01–1F
1
X
2nd Page General Purpose RAM
1 PSÐPage Select (Bit D7 of Main Status Register)
2 RSÐRegister Select (Bit D6 of Main Status Register)
(This extra 50 mA is not consumed if the battery backed
mode is selected).
DETAILED REGISTER DESCRIPTION
There are 5 external address bits: Thus, the host microproc-
essor has access to 28 locations at one time. An internal
switching scheme provides a total of 61 locations.
12
Functional Description (Continued)
MAIN STATUS REGISTER
The Periodic Flag Register has the same bit for bit corre-
spondence as Interrupt Control Register 0 except for D6
and D7. For normal operation (i.e., not a single supply appli-
cation) this register must be written to on initial power up or
after an oscillator fail event. D0–D5 are read only bits, D6
and D7 are read/write.
D0–D5: These bits are set by the real time rollover events:
e
read and can be used as selective data change flags.
(Time Change
1). The bits are reset when the register is
D6: This bit performs a dual function. When this bit is read, a
one indicates that an oscillator failure has occurred and the
time information may have been lost. Some of the ways an
oscillator failure might be caused are: failure of the crystal,
TL/F/11417–12
The Main Status Register is always located at address 0
regardless of the register block or the page selected.
shorting OSC IN or OSC OUT to GND or V , removal of
CC
crystal, removal of battery when in the battery backed mode
(when a ‘‘0’’ is written to D6), lowering the voltage at the
D0: This read only bit is a general interrupt status bit that is
taken directly from the interrupt pins. The bit is a one when
an interrupt is pending on either the INTR pin or the MFO
pin (when configured as an interrupt). This is unlike D3
which can be set by an internal event but may not cause an
interrupt. This bit is reset when the interrupt status bits in the
Main Status Register are cleared.
V
pin to a value less than 2.2V when in the battery
BB
backed mode. Bit D6 is automatically set to 1 on initial pow-
er-up or an oscillator fail event. The oscillator fail flag is
reset by writing a one to the clock start/stop bit in the Real
Time Mode Register, with the crystal oscillating.
When D6 is written to, it defines whether the TCP is being
used in battery backed (normal) or in a single supply mode
application. When set to a one this bit configures the TCP
for single power supply applications. This bit is automatically
set on initial power-up or an oscillator fail event. When set,
D6 disables the oscillator reference circuit. The result is that
D1–D3: These three bits of the Main Status Register are the
main interrupt status bits. Any bit may be a one when any of
the interrupts are pending. Once an interrupt is asserted the
mP will read this register to determine the cause. These
interrupt status bits are not reset when read. Except for D1,
to reset an interrupt a one is written back to the correspond-
ing bit that is being tested. D1 is reset whenever the PFAIL
the oscillator is referenced to V . When a zero is written to
CC
D6 the oscillator reference is enabled, thus the oscillator is
e
pin
logic 1. This prevents loss of interrupt status when
referenced to V . This allows operation in standard battery
BB
standby applications.
reading the register in a polled mode. D1 and D3 are set
regardless of whether these interrupts are masked or not by
bits D6 and D7 of Interrupt Control Registers 0 and 1.
At initial power on, if the LV8572A is going to be pro-
pin should be
grammed for battery backed mode, the V
BB
connected to a potential in the range of 2.2V to V
0.4V.
D4–D5: General purpose RAM bits.
b
CC
D6 and D7: These bits are Read/Write bits that control
which register block or RAM page is to be selected. Bit D6
controls the register block to be accessed (see memory
map). The memory map of the clock is further divided into
two memory pages. One page is the registers, clock and
timers, and the second page contains 31 bytes of general
purpose RAM. The page selection is determined by bit D7.
For single supply mode operation, the V pin should be
BB
connected to GND and the PFAIL pin connected to V
.
CC
D7: Writing a one to this bit enables the test mode register
at location 1F (see Table III). This bit should be forced to
zero during initialization for normal operation. If the test
mode has been entered, clear the test mode register before
leaving test mode. (See separate test mode application
note for further details.)
PERIODIC FLAG REGISTER
TIME SAVE CONTROL REGISTER
TL/F/11417–13
TL/F/11417–14
D0–D4: General purpose RAM bits.
13
Functional Description (Continued)
D5: The Delay Enable bit is used when a power fail occurs.
D2: The count mode for the hours counter can be set to
either 24 hour mode or 12 hour mode with AM/PM indicator.
A one will place the clock in 12 hour mode.
If this bit is set, a 480 ms delay is generated internally before
the mP interface is locked out. This will enable the mP to
access the registers for up to 480 ms after it receives a
power fail interrupt. After a power failure is detected but
prior to the 480 ms delay timing out, the host mP may force
immediate lock out by resetting the Delay Enable bit. Note if
this bit is a 0 when power fails then after a delay of 30 ms
min/63 ms max the mP cannot read the chip.
D3: This bit is the master Start/Stop bit for the clock. When
a one is written to this bit the real time counter’s prescaler
and counter chain are enabled. When this bit is reset to zero
the contents of the real time counter is stopped and the
prescaler is cleared. When the RTC is initially powered up
this bit will be held at a logic 0 until the oscillator starts
functioning correctly after which this bit may be modified. If
an oscillator fail event occurs, this bit will be reset to logic 0.
D6: This read only bit is set and reset by the voltage at the
pin. It can be used by the mP to determine whether the
V
BB
battery voltage at the V pin is getting too low. A compara-
BB
D4: This bit controls the operation of the interrupt output in
standby mode. If set to a one it allows Alarm, Periodic, and
Power Fail interrupts to be functional in standby mode. Note
that the MFO pin is configured as open drain in standby
mode.
tor monitors the battery and when the voltage is lower than
2.1V (typical) this bit is set. The power fail interrupt must be
enabled to check for a low battery voltage.
D7: Time Save Enable bit controls the loading of real-time-
clock data into the Time Save RAM. When a one is written
to this bit the Time Save RAM will follow the corresponding
clock registers, and when a zero is written to this bit the time
in the Time Save RAM is frozen. This eliminates any syn-
chronization problems when reading the clock, thus negat-
ing the need to check for a counter rollover during a read
cycle.
If bit D4 is set to a zero then interrupt control register and
the periodic interrupt flag will be reset when the RTC enters
l
the standby mode (V
BB
V ). They will have to be re-
CC
configured when system (V ) power is restored.
CC
D5: General purpose RAM.
D6 and D7: These two bits select the crystal clock frequen-
cy as per the following table:
This bit must be set to a one prior to power failing to enable
the Time Save feature. When the power fails this bit is auto-
matically reset and the time is saved in the Time Save RAM.
Crystal
XT1
XT0
Frequency
REAL TIME MODE REGISTER
0
0
1
1
0
1
0
1
32.768 kHz
4.194304 MHz
4.9152 MHz
32.000 kHz
All bits are Read/Write, and any mode written into this regis-
ter can be determined by reading the register. On initial
power up these bits are random.
OUTPUT MODE REGISTER
TL/F/11417–15
D0–D1: These are the leap year counter bits. These bits are
written to set the number of years from the previous leap
year. The leap year counter increments on December 31st
and it internally enables the February 29th counter state.
This method of setting the leap year allows leap year to
occur whenever the user wishes to, thus providing flexibility
in implementing Japanese leap year function.
TL/F/11417–16
Leap Year
LY1
LY0
D0–D6: General Purpose RAM
Counter
0
0
1
1
0
1
0
1
Leap Year Current Year
Leap Year Last Year
Leap Year 2 Years Ago
Leap Year 3 Years Ago
14
Functional Description (Continued)
D7: This bit is used to program the signal appearing at the
MFO output, as follows:
INTERRUPT CONTROL REGISTER 1
D7
MFO Output Signal
0
1
Power Fail Interrupt
Buffered Crystal Oscillator
INTERRUPT CONTROL REGISTER 0
TL/F/11417–18
D0–D5: Each of these bits are enable bits which will enable
a comparison between an individual clock counter and its
associated compare RAM. If any bit is a zero then that
clock-RAM comparator is set to the ‘‘always equal’’ state
and the associated TIME COMPARE RAM byte can be used
as general purpose RAM. However, to ensure that an alarm
interrupt is not generated at bit D3 of the Main Status Regis-
ter, all bits must be written to a logic zero.
TL/F/11417–17
D0–D5: These bits are used to enable one of the selected
periodic interrupts by writing a one into the appropriate bit.
These interrupts are issued at the rollover of the clock. For
example, the minutes interrupt will be issued whenever the
minutes counter increments. In all likelihood the interrupt
will be enabled asynchronously with the real time change.
Therefore, the very first interrupt will occur in less than the
periodic time chosen, but after the first interrupt all subse-
quent interrupts will be spaced correctly. These interrupts
are useful when minute, second, real time reading, or task
switching is required. When all six bits are written to a 0 this
disables periodic interrupts from the Main Status Register
and the interrupt pin.
D6: In order to generate an external alarm compare inter-
rupt to the mP from bit D3 of the Main Status Register, this
bit must be written to a logic 1. If battery backed mode is
selected then this bit is controlled by D4 of the Real Time
Mode Register.
D7: The MSB of this register is the enable bit for the Power
Fail Interrupt. When this bit is set to a one an interrupt will
l
be generated to the mP when V
BB
V
. If battery backed
CC
mode is selected then this bit is controlled by D4 of the Real
Time Mode Register.
This bit also enables the low battery detection analog cir-
cuitry.
D6 and D7: General Purpose RAM.
15
Control and Status Register Address Bit Map
D7
D6
D5
D4
ADDRESS
R/W
D3
D2
D1
D0
e
e
R/W
e
1. Reset by
writing
1 to bit.
Main Status Register PS
X
RS
X
00H
1
1
2
R
3
R
R/W
R/W
R/W
R/W
Page
Register
Select
Alarm
Interrupt
Periodic
Interrupt
Power Fail
Interrupt
Interrupt
Status
2. Set/reset by
voltage at
PFAIL pin.
RAM
RAM
Select
3. Reset when
all pending
interrupts
are removed.
e
e
e
Address 03H
Periodic Flag Register PS
0
RS
0
4. Read Osc fail
Write 0 Batt-
Backed Mode
Write 1 Single
Supply Mode
4
5
5
5
5
5
5
R/W
R/W
R
R
R
R
R
R
Test
Osc. Fail/
1 ms
Flag
10 ms
Flag
100 ms
Flag
Seconds
Flag
10 Second
Flag
Minute
Flag
Mode
Single Supply
5. Reset by
positive edge
of read.
e
e
e
Address 04H
Time Save Control Register PS
0
RS
0
6
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
Power Fail
Delay
6. Set and reset
Time Save Low Battery
Enable Flag
by V
BB
voltage.
RAM
RAM
RAM
RAM
RAM
Enable
e
e
e
Real Time Mode Register PS
0
RS
1
Address
01H
Crystal
Crystal
Interrupt EN
Clock
12/24 Hr.
Mode
Leap Year
MSB
Leap Year
LSB
RAM
All Bits R/W
Freq. XT1
Freq. XT0
on Back-Up Start/Stop
e
e
e
Output Mode Register PS
0
RS
RAM
1
Address
RAM
02H
RAM
MFO as
RAM
Crystal
RAM
RAM
RAM
All Bits R/W
All Bits R/W
e
e
e
Address 03H
Interrupt Control Register 0 PS
0
RS
1
1 ms
10 ms
100 ms
Interrupt
Enable
Seconds
Interrupt
Enable
10 Second
Interrupt
Enable
Minute
Interrupt
Enable
RAM
RAM
Interrupt
Enable
Interrupt
Enable
e
e
e
Address 04H
Interrupt Control Register 1 PS
0
RS
1
Power Fail
Interrupt
Enable
Alarm
Interrupt
Enable
DOW
Interrupt
Enable
Month
DOM
Interrupt
Enable
Hours
Interrupt
Enable
Minute
Interrupt
Enable
Second
Interrupt
Enable
Interrupt
Enable
All Bits R/W
16
Application Hints
Suggested Initialization Procedure for LV8572A in Battery
Backed Applications that use the V Pin.
BB
main the same as in step 1. Under normal operation, this
bit can be set only if the oscillator is running. During the
software loop, RAM, real time counters, output configu-
ration, interrupt control and timer functions may be ini-
tialized.
1. Enter the test mode by writing a 1 to bit D7 in the Period-
ic Flag Register.
2. Write zero to the RAM/TEST mode Register located in
page 0, address HEX 1F.
6. Test bit D6 in the Periodic Flag Register:
IF a 1, go to 5.1. If this bit remains a 1 after 3 seconds,
then abort and check hardware. The crystal may be de-
fective or not installed. There may be a short at OSC IN
3. Leave the test mode by writing a 0 to bit D7 in the Peri-
odic Flag Register. Steps 1,2,3 guarantee that if the test
mode had been entered during power on (due to ran-
dom pulses from the system), all test mode conditions
are cleared. Most important is that the OSC Fail Disable
bit is cleared. Refer to AN-589 for more information on
test mode operation.
or OSC OUT to V or GND, or to some impedance that
CC
is less than 10 MX.
IF a 0, then the oscillator is running, go to step 7.
7. Write a 0 to bit D6 in the Periodic Flag Register. This
action puts the clock chip in the battery backed mode.
This mode can be entered only if the OSC fail flag (bit
D6 of the Periodic Flag Register) is a 0. Reminder, Bit
D6 is a dual function bit. When read, D6 returns oscilla-
tor status. When written, D6 causes either the Battery
Backed Mode, or the Single Supply Mode of operation.
4. After power on (V
and V powered), select the cor-
BB
CC
rect crystal frequency bits (D7, D6 in the Real Time
Mode Register) as shown in Table IV.
TABLE IV
Frequency
32.768 kHz
4.194304 MHz
4.9152 MHz
32.0 kHz
D7
0
D6
0
The only method to ensure the chip is in the battery
backed mode is to measure the waveform at the OSC
OUT pin. If the battery backed mode was selected suc-
cessfully, then the peak to peak waveform at OSC OUT
is referenced to the battery voltage. If not in battery
0
1
1
0
backed mode, the waveform is referenced to V . The
CC
1
1
measurement should be made with a high impedance
low capacitance probe (10 MX, 10 pF oscilloscope
probe or better). Typical peak to peak swings are within
5. Enter a software loop that does the following:
Set a 3 second(approx) software counter. The crystal
oscillator may take 1 second to start.
0.6V of V
and ground respectively.
CC
8. Write a 1 to bit D7 of Interrupt Control Register 1. This
action enables the PFAIL pin and associated circuitry.
5.1 Write a 1 to bit D3 in the Real Time Mode Register (try
to start the clock). Make sure the crystal select bits re-
9. Initialize the rest of the chip as needed.
Typical Application
TL/F/11417–19
*These components may be necessary to meet UL requirements
for lithium batteries. Consult battery manufacturer.
17
Typical Performance Characteristics
Operating Current vs
Supply Voltage
(Battery Backed Mode
Operating Current vs
Supply Voltage
(Single Supply Mode
e
32.768 kHz,
F
OSC
e
e
F
OSC
32.768 kHz)
V
BB
2.5V)
TL/F/11417–20
TL/F/11417–21
Standby Current vs Power
Supply Voltage
Standby Current vs Power
Supply Voltage
e
e
4.194304 MHz
(F
32.768 kHz)
F
OSC
OSC
TL/F/11417–22
TL/F/11417–23
18
Physical Dimensions inches (millimeters)
Molded Small Outline Package (M)
Order Number LV8572AM
NS Package Number M24B
Molded Dual-In-Line Package (N)
Order Number LV8572AN
NS Package Number N24C
19
Physical Dimensions inches (millimeters) (Continued)
Plastic Chip Carrier Package (V)
Order Number LV8572AV
NS Package Number V28A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Corporation
National Semiconductor
Europe
National Semiconductor
Hong Kong Ltd.
National Semiconductor
Japan Ltd.
a
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
Fax:
(
49) 0-180-530 85 86
@
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
Tel: 81-043-299-2309
Fax: 81-043-299-2408
Email: cnjwge tevm2.nsc.com
a
a
a
a
Deutsch Tel:
English Tel:
Fran3ais Tel:
Italiano Tel:
(
(
(
(
49) 0-180-530 85 85
49) 0-180-532 78 32
49) 0-180-532 93 58
49) 0-180-534 16 80
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号:
©2020 ICPDF网 联系我们和版权申明