LM397MFX [NSC]
Single General Purpose Voltage Comparator; 单一的通用电压比较器
| 型号： | LM397MFX |
| 厂家： | 
National Semiconductor |
| 描述： | Single General Purpose Voltage Comparator |
| 文件： | 总8页 (文件大小：604K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
August 2006
LM397
Single General Purpose Voltage Comparator
General Description
Features
The LM397 is a single voltage comparator with an input
common mode that includes ground. The LM397 is designed
to operate from a single 5V to 30V power supply or a split
power supply. Its low supply current is virtually independent
of the magnitude of the supply voltage.
(TA = 25˚C. Typical values unless otherwise specified).
n 5-Pin SOT23 package
n Industrial operating range
n Single or dual power supplies
n Wide supply voltage range
n Low supply current
n Low input bias current
n Low input offset current
n Low input offset voltage
n Response time
−40˚C to +85˚C
5V to 30V
The LM397 features an open collector output stage. This
allows the connection of an external resistor at the output.
The output can directly interface with TTL, CMOS and other
logic levels, by tying the resistor to different voltage levels
(level translator).
300µA
7nA
1nA
2mV
440ns (50mV overdrive)
0 to VS - 1.5V
The LM397 is available in space saving 5-Pin SOT23 pack-
age and pin compatible to TI’s TL331, single differential
comparator.
n Input common mode voltage
Applications
n A/D converters
n Pulse, square wave generators
n Peak detector
n Industrial applications
Connection Diagram
Typical Circuit
5-Pin SOT23
20022108
Top View
20022109
FIGURE 1. Inverting Comparator with Hysteresis
Ordering Information
Package
Part Number
Package Marking
Transport Media
NSC Drawing
LM397MF
1k Units Tape and Reel
3k Units Tape and Reel
5-Pin SOT-23
C397
MF05A
LM397MFX
© 2006 National Semiconductor Corporation
DS200221
www.national.com
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Junction Temperature (Note 3)
Soldering Information
+150˚C
Infrared or Convection (20 sec.)
Wave Soldering (10 sec.)
235˚C
260˚C
ESD Tolerance (Note 2)
Human Body Model
Machine Model
2KV
Operating Ratings (Note 1)
Supply Voltage, VS
200V
30V
5V to 30V
VIN Differential
Temperature Range (Note 3)
Package Thermal Resistance (Note 3)
5-Pin SOT23
−40˚C to +85˚C
Supply Voltages
30V or 15V
−0.3V to 30V
−65˚C to +150˚C
Voltage at Input Pins
Storage Temperature Range
168˚C/W
Electrical Characteristics Unless otherwise specified, all limits are guaranteed for TA = 25˚C, VS = 5V, V−
0V, VCM = V+/2 = VO. Boldface limits apply at the temperature extremes.
=
Symbol
VOS
IOS
IB
Parameter
Input Offset Voltage
Input Offset Current
Input Bias Current
Supply Current
Conditions
Min
Typ
Max
Units
mV
nA
(Note 5) (Note 4) (Note 5)
VS = 5V to 30V,
2
7
VO = 1.4V, VCM = 0V
VO = 1.4V, VCM = 0V
10
1.6
10
50
250
250
400
0.7
2
VO = 1.4V, VCM = 0V
nA
IS
RL = Open, VS = 5V
RL = Open, VS = 30V
0.25
0.30
13
mA
+
−
IO
Output Sink Current
VIN = 1V,VIN = 0V, VO = 1.5V
6
mA
nA
+
−
ILEAKAGE Output Leakage Current
VIN = 1V,VIN = 0V, VO = 5V
0.1
1
+
−
VIN = 1V,VIN = 0V, VO = 30V
µA
+
−
VOL
VCM
AV
Output Voltage Low
IO = −4mA, VIN = 0V,VIN = 1V
180
400
700
mV
Common-Mode Input Voltage VS = 5V to 30V (Note 6)
Range
0
VS - 1.5V
VS - 2V
V
0
Voltage Gain
VS = 15V, VO = 1.4V to 11.4V,
120
900
250
940
440
V/mV
>
RL
= 15kΩ connected to VS
tPHL
Propagation Delay
(High to Low)
Input Overdrive = 5mV
RL = 5.1kΩ connected to 5V, CL = 15pF
Input Overdrive = 50mV
ns
RL = 5.1kΩ connected to 5V, CL = 15pF
Input Overdrive = 5mV
tPLH
Propagation Delay
(Low to High)
µs
ns
RL = 5.1kΩ connected to 5V, CL = 15pF
Input Overdrive = 50mV
RL = 5.1kΩ connected to 5V, CL = 15pF
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC)
Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
Note 3: The maximum power dissipation is
a
function of
T
, θ . The maximum allowable power dissipation at any ambient temperature is
J(MAX) JA
P
= (T - T )/ θ . All numbers apply for packages soldered directly onto a PC board.
D
J(MAX)
A
JA
Note 4: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.
Note 5: All limits are guaranteed by testing or statistical analysis.
Note 6: The input common-mode voltage of either input should not be permitted to go below the negative rail by more than 0.3V. The upper end of the
common-mode voltage range is V - 1.5V at 25˚C.
S
www.national.com
2
Typical Performance Characteristics TA = 25˚C. Unless otherwise specified.
Supply Current vs. Supply Voltage
Input Bias Current vs. Supply Current
20022103
20022101
Output Saturation Voltage vs. Output Sink Current
Input Offset Voltage vs. Supply Voltage
20022104
20022102
Response Time for Various Input Overdrives – tPHL
Response Time for Various Input Overdrives – tPLH
20022105
20022106
3
www.national.com
Application Notes
Basic Comparators
When input voltage (VIN) at the inverting node is less than
non-inverting node (VT), the output is high. The equivalent
circuit for the three resistor network is R1 in parallel with R3
and in series with R2. The lower threshold voltage VT1 is
calculated by:
A comparator is quite often used to convert an analog signal
to a digital signal. The comparator compares an input volt-
age (VIN) at the non-inverting pin to the reference voltage
(VREF) at the inverting pin. If VIN is less than VREF the output
(VO) is low (VOL). However, if VIN is greater than VREF, the
output voltage (VO) is high (VOH). Refer to Figure 2.
VT1 = ((VS R2) / (((R1 R3) / (R1 + R3)) + R2))
When VIN is greater than VT, the output voltage is low. The
equivalent circuit for the three resistor network is R2 in
parallel with R3 and in series with R1. The upper threshold
voltage VT2 is calculated by:
VT2 = VS ((R2 R3) / (R2 + R3)) / (R1 + ((R2 R3) / (R2
R3)))
+
The hysteresis is defined as
∆VIN = VT1 – VT2
20022110
20022112
20022111
FIGURE 2. Basic Comparator
Hysteresis
The basic comparator configuration may oscillate or produce
a noisy output if the applied differential input is near the
comparator’s input offset voltage. This tends to occur when
the voltage on the input is equal or very close to the other
input voltage. Adding hysteresis can prevent this problem.
Hysteresis creates two switching thresholds (one for the
rising input voltage and the other for the falling input volt-
age). Hysteresis is the voltage difference between the two
switching thresholds. When both inputs are nearly equal,
hysteresis causes one input to effectively move quickly pass
the other. Thus, effectively moving the input out of region that
oscillation may occur.
20022113
FIGURE 3. Inverting Configured Comparator – LM397
For an inverting configured comparator, hysteresis can be
added with a three resistor network and positive feedback.
www.national.com
4
Application Notes (Continued)
Input Stage
The LM397 has a bipolar input stage. The input common
mode voltage range is from 0 to (VS – 1.5V).
Output Stage
The LM397 has an open collector grounded-emitter NPN
output transistor for the output stage. This requires an exter-
nal pull-up resistor connected between the positive supply
voltage and the output. The external pull-up resistor should
be high enough resistance so to avoid excessive power
dissipation. In addition, the pull-up resistor should be low
enough resistance to enable the comparator to switch with
the load circuitry connected. Because it is an open collector
output stage, several comparator outputs can be connected
together to create an OR’ing function output. With an open
collector, the output can be used as a simple SPST switch to
ground.The amount of current which the output can sink is
approximately 10mA. When the maximum current limit is
reached, the output transistor will saturate and the output will
rise rapidly (Figure 4).
20022107
FIGURE 4. Output Saturation Voltage vs. Output Sink
Current
5
www.national.com
SOT23-5 Tape and Reel Specification
Tape Format
#
Tape Section
Cavities
Cavity Status
Empty
Cover Tape Status
Sealed
Leader (Start End)
0 (min)
75 (min)
3000
Empty
Sealed
Carrier
Filled
Sealed
1000
Filled
Sealed
Trailer (Hub End)
125 (min)
0 (min)
Empty
Sealed
Empty
Sealed
TAPE DIMENSIONS
20022115
8mm
0.130
(3.3)
0.124
(3.15)
0.130
0.126
(3.2)
0.138 0.002
0.055 0.004
(1.4 0.11)
DIM Ko
0.157
(4)
0.315 0.012
(8 0.3)
(3.3)
(3.5 0.05)
DIM F
Tape Size
DIM A
DIM Ao
DIM B
DIM Bo
DIM P1
DIM W
www.national.com
6
SOT23-5 Tape and Reel Specification (Continued)
REEL DIMENSIONS
20022116
8mm
7.00
0.059 0.512 0.795 2.165 0.331 + 0.059/−0.000 0.567
W1 + 0.078/−0.039
330.00 1.50 13.00 20.20 55.00
8.40 + 1.50/−0.00
W1
14.40
W2
W1 + 2.00/−1.00
W3
Tape Size
A
B
C
D
N
7
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
5-Pin SOT23
NS Package Number MF05A
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances
and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at:
www.national.com/quality/green.
Lead free products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
相关型号：
LM397MFX/NOPB
IC COMPARATOR, 10000 uV OFFSET-MAX, 940000 ns RESPONSE TIME, PDSO5, LEAD FREE, SOT-23, 5 PIN, Comparator
NSC
©2020 ICPDF网 联系我们和版权申明