C2012C0G2A102J [NSC]
Evaluation Board provides the design engineer with a fully functional; 评估板提供了设计工程师提供一个功能齐全型号: | C2012C0G2A102J |
厂家: | National Semiconductor |
描述: | Evaluation Board provides the design engineer with a fully functional |
文件: | 总10页 (文件大小:1211K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
National Semiconductor
Application Note 2066
Eric Lee
LM25119 Evaluation Board
September 28, 2010
ed to the J6 (OUT2+) and J5 (OUT2-/GND). Be sure to
choose the correct connector and wire size when attaching
the source power supply and the load.
Introduction
The LM25119EVAL evaluation board provides the design en-
gineer with a fully functional dual output buck converter, em-
ploying the LM25119 Dual Emulated Current Mode Syn-
chronous Buck Controller. The evaluation board is designed
to provide both 3.3V and 1.8V outputs over an input range of
6.0V to 36V. Also the evaluation board can be easily config-
ured for a single 3.3V, 16A regulator.
SOURCE POWER
The power supply and cabling must present low impedance
to the evaluation board. Insufficient cabling or a high
impedance power supply will droop during power supply ap-
plication with the evaluation board inrush current. If large
enough, this droop will cause a chattering condition during
power up. During power down, insufficient cabling or a high
impedance power supply will overshoot. This overshoot will
cause a non-monotonic decay on the output.
Performance of the Evaluation
Board
•
•
•
•
•
•
•
•
Input Voltage Range: 6.0V to 36V
Output Voltage: 3.3V (CH1), 1.8V (CH2)
Output Current: 8A (CH1), 8A (CH2)
Nominal Switching Frequency: 230 KHz
Synchronous Buck Operation: Yes
Diode Emulation Mode: Yes
An additional external bulk input capacitor may be required
unless the output voltage droop/overshoot of the source pow-
er is less than 0.5V. In this board design, UVLO setting is
conservative while UVLO hysteresis setting is aggressive.
Minimum input voltage can goes down with an aggressive
design. Minimum operating input voltage depends on the out-
put voltage droop/overshoot of the source power supply and
the forced off-time of the LM25119. Refer to the LM25119
datasheet for complete design information.
Hiccup Mode Overload Protection: Yes
External VCC Sourcing: No
LOADING
Powering and Loading
Consideration
When applying power to the LM25119 evaluation board, cer-
tain precautions need to be followed. A misconnection can
damage the assembly.
When using an electronic load, it is strongly recommended to
power up the evaluation board at light load and then slowly
increase the load. If it is desired to power up the evaluation
board at maximum load, resistor banks must be used. In gen-
eral, electronic loads are best suited for monitoring steady
state waveforms.
PROPER BOARD CONNECTION
AIR FLOW
The input connections are made to the J1 (VIN) and J2 (RTN/
GND) connectors. The CH1 load is connected to the J3
(OUT1+) and J4 (OUT1-/GND) and the CH2 load is connect-
Prolonged operation with high input voltage at full power will
cause the MOSFETs to overheat. A fan with a minimum of
200LFM should be always provided.
30126101
FIGURE 1. Typical Evaluation Setup
© 2010 National Semiconductor Corporation
301261
www.national.com
QUICK START-UP PROCEDURE
LOAD TRANSIENT
STEP 1: Set the power supply current limit to at least 20A.
Connect the power supply to J1 and J2.
Figure 3 shows the transient response for a load of change
from 2A to 6A on 3.3V output. The upper waveform shows
output voltage droop and overshoot during the sudden
change in output current shown by the lower waveform.
STEP 2: Connect one load with an 8A capacity between J3
and J4. Connect another load with an 8A capacity between
J6 and J5.
STEP 3: Set input voltage to 12V and turn it on.
STEP 4: Measure the output voltages. CH1 should regulate
at 3.3V and CH2 should regulate at 1.8V.
STEP 5: Slowly increase the load current while monitoring the
output voltages. The outputs should remain in regulation up
to full load current.
STEP 6: Slowly sweep the input voltage from 6.0V to 36V
while monitoring the output voltages. The outputs should re-
main in regulation.
Waveforms
SOFT START
When applying power to the LM25119 evaluation board a
certain sequence of events occurs. Soft-start capacitors and
other components allow for a linear increase in output volt-
ages. The soft-start time of each output can be controlled
independently. Figure 2 shows the output voltage during a
typical start-up with a load of 0.5Ω on the 3.3V output, and
0.33Ω on the 1.8V output, respectively.
30126103
Conditions:
Input Voltage = 12VDC
Output Current 2A to 6A
Traces:
Top Trace: 3.3V Output Voltage, Volt/div = 100mV, AC coupled
Bottom Trace: Output Current Amp/Div = 2A
Horizontal Resolution = 0.5 ms/div
FIGURE 3. Load Transient Response
OVER LOAD PROTECTION
The evaluation board is configured with hiccup mode over-
load protection. The restart time can be programmed by C11.
Figure 4 shows hiccup mode operation in the event of an out-
put short on CH1 output. One channel may operate in the
normal mode while the other is in hiccup mode overload pro-
tection.
30126102
Conditions:
Input Voltage = 12VDC
0.5Ω Load on 3.3V output
0.33Ω Load on 1.8V output
Traces:
Top Trace: 3.3V Output Voltage, Volt/div = 1V
Bottom Trace: 1.8V Output Voltage, Volt/div = 1V
Horizontal Resolution = 1 ms/div
FIGURE 2. Start-up with Resistive Load
30126104
Conditions:
Input Voltage = 12VDC
Output Short on 3.3V
Traces:
Top Trace: SW voltage on CH1, Volt/div = 10V
Bottom Trace: Inductor Current Amp/div = 10A
Horizontal Resolution = 20 ms/div
FIGURE 4. Short Circuit
www.national.com
2
EXTERNAL CLOCK SYNCHRONIZATION
Performance Characteristics
A TP1 (SYNC) test point has been provided on the evaluation
board in order to synchronize the internal oscillator to an ex-
ternal clock. Figure 5 shows the synchronized switching op-
eration. Each channel operates 180 degrees out of phase
from the other.
Figure 7 shows the efficiency curves. The efficiency of the
power converter is 90% at 12V with full load current. Monitor
the current into and out of the evaluation board. Monitor the
voltage directly at the input and output terminals of the eval-
uation board.
30126105
Conditions:
Input Voltage = 12VDC
8A on 3.3V output
8A on 1.8V output
Traces:
Top Trace: SYNC pulse, Volt/div = 5V
Middle Trace: SW voltage on CH1, Volt/div = 10V
Bottom Trace: SW voltage on CH2, Volt/div = 10V
Horizontal Resolution = 1 µs/div
30126107
FIGURE 7. Typical Efficiency vs Load Current
FIGURE 5. Clock Synchronization
SHUTDOWN
Figure 6 shows the shutdown procedure by powering off the
source power. When UVLO pin voltage is less than 1.26V, the
switching stops and soft-start capacitors are discharged by
internal switches.
30126106
Conditions:
Input Voltage = 12VDC
0.5Ω Load on 3.3v output
Traces:
Top Trace: Input Voltage, Volt/div = 10V
Middle Trace1: 3.3V Output, Volt/div = 2V
Middle Trace2: VCC, Volt/div = 5V
Bottom Trace: SS voltage, Volt/div = 5V
Horizontal Resolution = 20 ms/div
FIGURE 6. Shutdown
3
www.national.com
EXTERNAL VCC SUPPLY & VCC DISABLE
Board Configuration
External VCC supply helps to reduce the temperature and the
power loss of the LM25119 at high input voltage. By populat-
ing D3 and D4, VCC can be supplied from an external power
supply. Use TP3 as an input of the external VCC supply with
0.1A current limit. R36, R35 and C45 should be populated
with proper value when the voltage of the external VCC is
smaller than 7V. The voltage at the VCCDIS pin can be mon-
itored at TP2. To prevent a reverse current flow from VCC to
VIN through the internal diode, the external VCC voltage
should always be lower than VIN.
INTERLEAVED BUCK OPERATION FOR SINGLE 3.3V
16A OUTPUT
The evaluation board is designed to be easily converted to a
3.3V, 16A single output regulator with the interleaved opera-
tion. Proper electronic load connection is shown in Figure 8.
Connecting the electronic load at the center of shorting bar is
recommended to prevent a voltage difference between CH1
and CH2 output. In order to produce a single 3.3V output with
16A maximum output current, populate R21 and R22 with
0Ω resistor and open R6, C15 and C14. The electronic load
should have over 16A capability to test the interleaved oper-
ation.
LOOP RESPONSE
TP5 and TP6 (TP7 and TP8) have been provided in order to
measure the loop transfer function of CH1 (CH2). Refer to
AN-1889 for detail information about the loop transfer function
measurement.
30126108
FIGURE 8. Load Connection for Single Output
30126109
FIGURE 9. Loop Response Measurement Setup
www.national.com
4
Evaluation Board Schematic
30126110
5
www.national.com
TABLE 1. Bill of Materials
Part
Value
Package
Part Number
Manufacturer
C1,C2,C3,C4,C5,C32,
C35,C36,C37,C38,C39
,C40,C41,C42
2.2 µF, 50V, X7R
1210
C3225X7R1H225K
TDK
C6,C7,C25,C29
C8,C10,C14,C16
C9
1µF, 16V, X7R
100pF, 50V, C0G
0.47µF, 50V, X7R
0.47µF, 25V, X7R
0.047µF, 16V, X7R
6800pF, 25V, C0G
820pF, 50V, C0G
680µF, 6.3V
0603
0603
0805
0603
0603
0603
0603
Φ10
C1608X7R1C105K
C1608C0G1H101J
UMK212B7474KG
TDK
TDK
Taiyo Yuden
Murata
TDK
C11,C18,C19
C12,C13
GRM188R71E474KA12
C1608X7R1C473K
C1608C0G1E682J
C15,C17
TDK
C20,C21
C1608C0G1H821J
APXA6R3ARA681MJC0G
TDK
C22,C26
NIPPON CHEMI-
CON
C23,C24,C27,C28
22µF,10V, X7R
1000pF, 50V, X7R
1000pF,100V, C0G
NU
1210
0603
0805
C1210C226K8RAC
C1608X7R1H102K
C2012C0G2A102J
Kemet
TDK
C30,C31
C33,C34
TDK
C43,C44,C45,C46,C47
R1
R2
R3
R4
3.9 ohm, 5%
52.3k, 1%
0805
0805
0603
0603
CRCW08053R90JNEA
MCR10EZHF5232
Vishay
Rohm
Rohm
Vishay
15k, 1%
MCR03EZPFX1502
CRCW060322K1FKEA
22.1k, 1%
R5,R16,R21,R22,R35,
R36,R37
NU
R6,R7
36.5k, 1%
0603
0805
CRCW060336K5FKEA
CRCW080510R0JNEA
Vishay
Vishay
R8,R9,
R23,R24,R29,R30,
R31, R32
10 ohm, 5%
R10,R12
R11
6.98k, 1%
2.21k, 1%
5.49k, 1%
34k, 1%
0805
0805
CRCW08056K98FKEA
MCR10EZHF2211
MCR10EZHF5491
CRCW060334K0FKEA
MCR03EZPJ000
Vishay
Rohm
R13
0805
Rohm
R14,R15
R17
0603
Vishay
0 ohm
0603
Rohm
R18,R20
R25,R26
R27,R28
D1,D2
0.008 ohm, 1W, 1%
5.1 ohm, 1W, 1%
0 ohm, 5%
60V, 1A
0815
RL3720WT-R008-F
ERJ-1TRQF5R1U
MCR10EZPJ000
Susumu
Panasonic-ECG
Rohm
2512
0805
SOD123F
PMEG6010CEH
NXP
D3,D4
NU
L1,L2
6.8µH, 18.5A
40V, 58A
18.2x18.3
PowerPAK SO-8
LLP32
7443556680
SI7884BDP
LM25119
7693
WE
Q1,Q2,Q3,Q4
U1
Vishay
NSC
J1,J2,J3,J4,J5,J6
TP1,TP2,TP3
TP5,TP6,TP7,TP8
15A
Keystone
Keystone
Keystone
5002
Φ10
1040
www.national.com
6
PCB Layout
30126111
30126115
7
www.national.com
30126112
30126113
www.national.com
8
30126114
30126116
9
www.national.com
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products
www.national.com/amplifiers
Design Support
www.national.com/webench
Amplifiers
WEBENCH® Tools
App Notes
Audio
www.national.com/audio
www.national.com/timing
www.national.com/adc
www.national.com/interface
www.national.com/lvds
www.national.com/power
www.national.com/appnotes
www.national.com/refdesigns
www.national.com/samples
www.national.com/evalboards
www.national.com/packaging
www.national.com/quality/green
www.national.com/contacts
www.national.com/quality
www.national.com/feedback
www.national.com/easy
Clock and Timing
Data Converters
Interface
Reference Designs
Samples
Eval Boards
LVDS
Packaging
Power Management
Green Compliance
Distributors
Switching Regulators www.national.com/switchers
LDOs
www.national.com/ldo
www.national.com/led
www.national.com/vref
www.national.com/powerwise
Quality and Reliability
Feedback/Support
Design Made Easy
Applications & Markets
Mil/Aero
LED Lighting
Voltage References
PowerWise® Solutions
www.national.com/solutions
www.national.com/milaero
www.national.com/solarmagic
www.national.com/training
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
PLL/VCO
www.national.com/tempsensors SolarMagic™
www.national.com/wireless
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2010 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
National Semiconductor Europe
Technical Support Center
Email: europe.support@nsc.com
National Semiconductor Asia
Pacific Technical Support Center
Email: ap.support@nsc.com
National Semiconductor Japan
Technical Support Center
Email: jpn.feedback@nsc.com
Email: support@nsc.com
Tel: 1-800-272-9959
www.national.com
相关型号:
C2012C0G2A103J125AA
Ceramic Capacitor, Multilayer, Ceramic, 100V, 5% +Tol, 5% -Tol, C0G, 30ppm/Cel TC, 0.01uF, Surface Mount, 0805, CHIP, ROHS COMPLIANT
TDK
©2020 ICPDF网 联系我们和版权申明