CF5034MB [NPC]
350MHz PECL-output Oscillator ICs; 350MHz的PECL输出振荡器集成电路型号: | CF5034MB |
厂家: | NIPPON PRECISION CIRCUITS INC |
描述: | 350MHz PECL-output Oscillator ICs |
文件: | 总6页 (文件大小:80K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CF5034 series
350MHz PECL-output Oscillator ICs
OVERVIEW
The CF5034 series are differential LVPECL output oscillator ICs. They are made using a BiCMOS process
which allows high-frequency oscillator circuits and differential LVPECL output circuits to be fabricated on a
single chip. Two oscillator modes are supported—350MHz maximum fundamental oscillation mode, and
80MHz to 160MHz 3rd overtone oscillation mode.
The CF5034 series devices require only the connection of a crystal to realize a differential LVPECL output
oscillator circuit.
FEATURES
ꢀ 3.3 0.3V operating supply voltage
ꢀ Oscillator frequency range
• 80MHz to 350MHz fundamental oscillation
mode
ꢀ f (oscillator frequency) or f /2 output frequency,
O O
determined by internal connection
ꢀ 50 5ꢀ output duty (measured at output crossing
point)
• 80MHz to 160MHz 3rd overtone oscillation
mode
ꢀ Standby function: outputs are high impedance
when OE is LOW.
ꢀ 40MHz to 350MHz output frequency range
ꢀ Differential LVPECL output
ꢀ Power-saving pull-up resistor built-in (pin OE)
ꢀ Chip form (CF5034××)
SERIES LINEUP
Recommended oscillator
1
Version
Oscillation mode
Output frequency
frequency [MHz]
CF5034AA
CF5034AB
CF5034BA
CF5034BB
CF5034DA
CF5034DB
CF5034LA
CF5034LB
CF5034MA
CF5034MB
f
O
250 to 350
f /2
O
Fundamental
f
O
160 to 250
80 to 350
f /2
O
f
O
–
(external capacitors required)
f /2
O
f
O
125 to 160
f /2
O
Fundamental or
3rd overtone
f
O
80 to 125
f /2
O
1. The recommended oscillator frequency criteria is based on the negative resistance characteristics and cutoff frequency. Note that this may change
depending on the crystal characteristics, thus sufficient allowance should be made.
ORDERING INFORMATION
Device
Package
CF5034××−1
Chip form
NIPPON PRECISION CIRCUITS INC.—1
CF5034 series
PAD LAYOUT
(Unit: µm)
OUTN
8
TEST
(1160,1310)
OUT
9
VCC2 OE
7
6
5
Y
1
2
3
4
(0,0)
VCC
XIN XOUT GND
X
Chip size: 1.16 × 1.31mm
Chip thickness: 300 30ꢀm
Chip base: GND potential
PAD DESCRIPTION AND DIMENSIONS
Pad dimensions [µm]
Pad No.
Name
I/O
Function
X
Y
1
2
3
4
VCC
XIN
–
I
Supply pin
146
536
809
1015
145
145
145
145
Oscillator input pin
Oscillator output pin
Ground pin
XOUT
GND
O
–
Output enable pin. Outputs are high impedance when LOW (oscillator
stopped). Power-saving pull-up resistor built-in.
5
OE
I
979
1165
6
7
8
9
TEST
VCC2
OUTN
OUT
I
IC test pin. Leave open circuit for normal operation.
Output buffer supply pin
839
690
449
216
1165
1165
1165
1165
–
O
O
Output pin (complementary)
Output pin (true)
BLOCK DIAGRAM
OE
VCC2
VCC
OUT
Rf
1/2
ECL
OUTN
XIN
CXOUT
CXIN
GND
XOUT
NIPPON PRECISION CIRCUITS INC.—2
CF5034 series
ABSOLUTE MAXIMUM RATINGS
Parameter
Supply voltage range
Symbol
Conditions
Rating
Unit
V
V
−0.5 to 7.0
CC
Input voltage range
V
GND − 0.5 to V + 0.5
CC
V
IN
Output voltage range
Storage temperature range
V
GND − 0.5 to V + 0.5
CC
V
OUT
T
−65 to 150
°C
STG
RECOMMENDED OPERATING CONDITIONS
Rating
Parameter
Symbol
Conditions
Unit
Min
Typ
3.3
–
Max
3.6
Operating supply voltage
Input voltage
V
3.0
GND
−40
–
V
V
CC
V
V
CC
IN
Operating temperature
Output load
T
25
50
–
85
°C
Ω
OPR
RL
Terminated to V − 2V
CC
–
Output frequency
f
40
350
MHz
OUT
ELECTRICAL CHARACTERISTICS
DC Characteristics
Recommended operating conditions unless otherwise noted.
Rating
Parameter
Symbol
Conditions
Unit
Min
–
Typ
Max
88
Current consumption 1
Current consumption 2
I
Measurement cct. 1, OE = open
Measurement cct. 1, OE = LOW
55
mA
ꢀA
V
EE1
I
–
–
2.350
2.295
1.600
1.605
–
30
EE2
Ta = 0 to 85°C
2.275
2.215
1.490
1.470
–
2.420
2.420
1.680
1.745
10
OUT/OUTN HIGH-level output voltage
OUT/OUTN LOW-level output voltage
V
OH
Measurement cct. 4,
= 3.3V,
OE = open
Ta = – 40°C
Ta = 0 to 85°C
Ta = – 40°C
V
V
CC
V
V
OL
V
OUT/OUTN output leakage current
OE HIGH-level input voltage
OE LOW-level input voltage
OE LOW-level input current 1
OE LOW-level input current 2
I
Measurement cct. 2, OE = LOW
Measurement cct. 1
ꢀA
V
Z
V
0.7V
–
–
IH
CC
V
Measurement cct. 1
–
–
0.3V
V
IL
CC
I
Measurement cct. 2, V = 0V
IL
−2
–
−20
ꢀA
ꢀA
IL1
I
Measurement cct. 2, V = 0.7V
CC
−20
–
−200
IL2
IL
NIPPON PRECISION CIRCUITS INC.—3
CF5034 series
AC Characteristics
Recommended operating conditions unless otherwise noted.
Rating
Typ
Parameter
Symbol
Conditions
Unit
Min
Max
Measurement cct. 3,
measured at output crossing point,
Output duty cycle 1
Duty 1
45
–
–
55
%
Ta = 25°C, V = 3.3V
CC
Measurement cct. 3,
measured at 50% output swing,
Output duty cycle 2
Duty 2
45
55
%
Ta = 25°C, V = 3.3V
CC
Measurement cct. 1, Ta = T , f = 350MHz,
OPR
Peak to peak of output waveform
1
Output swing
V
0.4
–
–
–
1
1
V
Opp
Measurement cct. 3,
20 to 80% output swing
Output rise time
Output fall time
t
0.5
0.5
ns
ns
r
Measurement cct. 3,
80 to 20% output swing
t
–
f
2
Output enable time
t
Measurement cct. 1, Ta = 25°C
Measurement cct. 1, Ta = 25°C
–
–
–
–
200
200
ns
ns
OE
2
Output disable time
t
OD
1. The said values are measured by using the NPC standard jig.
2. The built-in oscillator stop function does not operate with normal output immediately when OE goes HIGH. Instead, normal output occurs after the
oscillator startup time has elapsed.
VDD
VOpp
tr
tf
OUTN
OUT
VOH
80%
20%
VOL
VDD – 2V
tW
tPER
DUTY = tW/tPER 100
VSS
tOD
tOE
OE
VDD
VIH
VIL
OE input waveform tr = tf 10ns
VSS
Timing chart
NIPPON PRECISION CIRCUITS INC.—4
CF5034 series
FUNCTIONAL DESCRIPTION
Standby Function
Power-saving Pull-up Resistor
When OE goes LOW, the oscillator stops and the
output pins (OUT, OUTN) become high impedance.
The OE pin pull-up resistance changes in value in
response to the input level (HIGH or LOW). When
OE is LOW (standby state), the pull-up resistance
increases, thereby decreasing the current consump-
tion.
OE
HIGH (or open)
LOW
OUT, OUTN
Oscillator
Normal operation
Stopped
Either f or f /2
O
O
High impedance
MEASUREMENT CIRCUITS
Measurement Circuit 1
Measurement Circuit 3
IEE1, IEE2
A
VCC
XIN
VCC2
OUT
VCC
XIN
VCC2
OUT
C1
R1
R1
Signal
Generator
R1
R1
R1
VT
VT
OE
OUTN
GND
XOUT
OUTN
GND
VOE
XIN input signal 500mVp-p, sine wave
C1: 0.001ꢀF
R1: 50Ω, V : V − 2V
T CC
R1: 50Ω
Measurement Circuit 4
V : V − 2V
T
CC
: V , V , V
V
OE CC IH IL
Measurement Circuit 2
VCC
XIN
VCC2
R1
R1
OUT
VT
VCC
VCC2
OUT
XOUT
OUTN
A
A
A
TEST GND
OE
OUTN
GND
0.7VCC
R1: 50Ω, V : V − 2V
T
CC
XOUT = HIGH: OUT pin is fixed HIGH (V ).
OH
OUTN pin is fixed LOW (V ).
XOUT = LOW: OUT pin is fixed LOW (V ).
OL
OL
OUTN pin is fixed HIGH (V ).
OH
NIPPON PRECISION CIRCUITS INC.—5
CF5034 series
Please pay your attention to the following points at time of using the products shown in this document.
The products shown in this document (hereinafter “Products”) are not intended to be used for the apparatus that exerts harmful influence on
human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such
use from NIPPON PRECISION CIRCUITS INC. (hereinafter “NPC”). Customers shall be solely responsible for, and indemnify and hold NPC
free and harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves
the right to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or
warranty that the contents described in this document dose not infringe any intellectual property right or other similar right owned by third
parties. Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this
document. Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the
Products, and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing
or modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in
compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested
appropriately take steps to obtain required permissions or approvals from appropriate government agencies.
NIPPON PRECISION CIRCUITS INC.
4-3, Fukuzumi 2-chome, Koto-ku,
Tokyo 135-8430, Japan
Telephone: +81-3-3642-6661
Facsimile: +81-3-3642-6698
http://www.npc.co.jp/
Email: sales@npc.co.jp
NC0116CE 2003.04
NIPPON PRECISION CIRCUITS INC.—6
相关型号:
©2020 ICPDF网 联系我们和版权申明