NSVS1134 [NJRC]

1-Port Saw Resonator, 315MHz Nom, SMALL, SMD, 8 PIN;


型号：	NSVS1134
厂家：	NEW JAPAN RADIO
描述：	1-Port Saw Resonator, 315MHz Nom, SMALL, SMD, 8 PIN 晶体谐振器
文件：	总3页 (文件大小：101K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

NSVS1134 Apr. 2013

NewJRC STW RESONATOR

NSVS1134

Application

315.00MHz Resonator

Electrical Specification: (Table 1)

The device characteristics are measured in the circuit shown in Fig.2.

Table 1. Electrical Specifications

(@25 ºC)

Typ.

Item

Spec.

Center frequency

Absolute frequency

315.000MHz

±100kHz

Tolerance from 315.000MHz

@Minimum Loss

Insertion Loss

2.5dB max.

Temperature Stability Turnover Temperature

Temperature Coefficient

33 ºC

-0.040 ppm/ºC²

DC Insulation Resistance between any two terminals

1.0M ohm min.

RF Equivalent

RLC Model (fig.1)

Motional Resistance

Motional Inductance

Motional Capacitance

Shunt Static Capacitance

19.0 ohm

38.275 μH

6.670 fF

3.40 pF

Maximum Rating: (Table 2)

Table2. Maximum Ratings

Item

Rating

+5dBm

Maximum Input Power

Operating Temperature Range

Storage Temperature

-30~+85ºC

-40~+90ºC

Fig.1 RF Equivalent RLC Model

Mechanical Specifications: (Fig.3)

Package is designed as small as 3.5x3.5x1.0[mm³] for SMD (Surface Mount Device) type.

Notice:

This part is electrostatic discharge sensitive and may be damaged by improper handling.

http://www.njr.co.jp/products/device/index.html

http://www.njr.com/products/device/index.html

(Japanese)

(English)

NSVS1134 Apr. 2013

OUT

50Ω

SAW 6

3 4 5

Fig.2 Measuring circuit

3. 5±0. 2

(b)

(a)

(c)

221

(1)

(2)

Marking

(1) Lot Number

(a) Year

(0. 95)

(0. 8)

[ 5x]

(b) Month

*Oct.---

Nov.---

Dec.---

(0. 6)

*1-9---

10-19---

20-31---

(2) Part Number Mark

Fig.3 Package dimensions (in mm)

Pin no.

Connection

GND

4. 3

0. 8

1. 3

[6x]

IN/OUT

GND

OUT/IN

GND

Via-Hole(Φ0.3)

GND

Fig.4 Desirable land area (in mm)

NSVS1134 Apr. 2013

Notice

1. Use this component within operating temperature range. It might not be

satisfied with electrical specification without operating temperature range.

When it is used less than -30ºC or more than +85ºC, it might be a cause of

degradation or destruction of the component. Even if it endures during a short

time, it causes degradation of qualification.

2. When soldering iron is used, solder with the temperature at the tip of soldering

iron: 350ºC max., the time of soldering: 10 seconds max., the power of

soldering iron: 30W max..

3. Notice that the allowed time of soldering with soldering iron is accumulated

time, when soldering is repeated.

4. As rapid temperature change for cleaning after reflow soldering might be a

cause of destruction clean this component after confirming that temperature of

this component goes down to room temperature.

5. Confirm that there are not any influence for qualification to this component in

mounting on PCB when this component is cleaned.

6. As it might be a cause of degradation of destruction to apply static electricity to

this component, do not apply static electricity or excessive voltage while

assembling and measuring. And do not transport this component with bare

hand.

Note

1. This specification specifies the quality of this component as a single unit. Make

sure that this component is evaluated and confirmed against this specification

when it is mounted to your products.

2. The information contained herein may be changed without prior notice. It is

therefore advisable to contact New Japan Radio Company before proceeding

with the design of equipment incorporating this product.

3. The products are designed to be used with ordinary electronic equipment (data

and communications equipment, office equipment, audio-video equipment,

measuring instruments, etc). New Japan Radio Company does not assume any

liability for the case using the products with the application required high

reliability or safety extremely (such as space equipment, sea-bottom equipment,

medical equipment etc). When intending to use any our product please

contact our sales representatives in advance.

相关型号：