F110E227MDL [NICHICON]
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 2.5V, 20% +Tol, 20% -Tol, 220uF, Surface Mount, 3321, CHIP, ROHS COMPLIANT;
| 型号： | F110E227MDL |
| 厂家： | 
NICHICON CORPORATION |
| 描述： | Tantalum Capacitor, Polarized, Tantalum (dry/solid), 2.5V, 20% +Tol, 20% -Tol, 220uF, Surface Mount, 3321, CHIP, ROHS COMPLIANT 电容器 |
| 文件： | 总2页 (文件大小：69K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DECOUPLING DEVICE FOR HIGH FREQUENCY
F1 1
Higher Capacitance.
Low ESR, Low ESL,High ripple current.
Resin-molded Chip.
Specifications
Item
Performance Characteristics
Designed for surface mounting on high density PC board.
+
°
Load life of 5000 hours at 105°C.
Category Temperature Range −55 to +105 C
Compliant to the RoHS directive (2002/95/EC).
Capacitance Tolerance ±20% (at 120Hz)
Dissipation Factor
ESR
Refer to next table
Refer to next table
After 5 minute’s application of rated voltage,
leakage current is not more than 0.1CV
Leakage Current
°
At 60 C 90%RH 500hours (No voltage applied)
..Within −20 to +30% of the initial specified value
Capacitance Change
.......
Damp Heat
(Steady State)
Dissipation Factor
200% or less than the Initial specified value
200% or less than the Initial specified value
Initial specified value or less
............................
ESR
Leakage Current
.........
°
°
−55 C / +105 C 30minutes each 5cycle
..
Capacitance Change Within ±20% of the Initial specified value
Dissipation Factor
ESR
Leakage Current
Temperature Cycles
.......
200% or less than the Initial specified value
200% or less than the Initial specified value
Initial specified value or less
............................
.........
Type numbering system (Example : 2.5V 220µF)
°
°
−55 C
+105 C
1
2
3
4
5
6
7
8
9
10 11 12 13 14
Capacitance Change Within −20 to +0%
Dissipation Factor Initial specified value or less 150% or less than the Initial specified value
Initial specified value or less 150% or less than the Initial specified value
Within −0 to +50%
Temperature Change
Characteristics
F 1 1 0 E 2 2 7 M D L A H
ESR
Low ESR
Leakage Current Initial specified value or less 10 times Initial specified value
Taping code
Capacitor meets the following characteristics after solder reflow
°
Reel Dia
(mm)
Tape width
(mm)
(Peak: 240
C for 10sec, 2cycle).
code
Temperature should be measured at the terminals.
Resistance
to Soldering Heat
L
16
24
φ180
φ330
..
Capacitance Change Within ±20% of the Initial specified value
Dissipation Factor
ESR
Leakage Current
K
.......
Initial specified value or less
Initial specified value or less
Initial specified value or less
............................
Case code
.........
Capacitance tolerance
Rated capacitance
Rated voltage
Series
After application of 115% of rating voltage at the rate of
30 seconds ON, 30 seconds OFF, for 1000 successive
test cycles at 105 C, capacitors meet the characteristics
°
requirements listed below.
Surge
....
Capacitance Change Within ±20% of the initial specified value
.........
..............................
...........
Dissipation Factor
ESR
Leakage Current
200% or less than the Initial specified value
200% or less than the Initial specified value
Initial specified value or less
Dimensions
L1
°
After 5000 hours’ application of rated voltage at 105 C, they will meet
the specified value for life charecteristics listed below.
....
Capacitance Change Within ±20% of the initial value
W2
Endurance
Marking
.........
Dissipation Factor
200% or less than the Initial specified value
200% or less than the Initial specified value
Initial specified value or less
W1
..............................
ESR
...........
Leakage Current
H
Printed on the package top.
P
S2
S3
S1
L2
(
mm)
Case Code
W1
7.3 ± 0.2 5.3 ± 0.2
15.6 ± 0.2
W2
L2
H
S1
S2
S3
P
L1
D
F
8.5 ± 0.2
1.7 ± 0.2
3.6 ± 0.2
2.0MAX. 0.9 ± 0.2 0.6 ± 0.2 0.5 ± 0.2 3.3 ± 0.2
2.5MAX. 1.5 ± 0.1 1.3 ± 0.1 1.5 ± 0.2 7.0 ± 0.2
16.7 ± 0.2
12.1 ± 0.2
Marking
Standard ratings
V
2.5
0E
4
0G
D
6.3
0J
D
Code
476
107
227
337
607
807
128
Cap.(
µ )
F
F case only
Seriese
47
F11
100
220
330
600
800
D
D
( )
D
D
( )
D
0E128M
Capacitance Tolerance
8J1234
Rated Capacitance
(Capacitance code)
( )
D
Rated Voltage
(Voltage code)
Lot No.
F
F
F
1200
F
(
)
The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
CAT.8100Y
DECOUPLING DEVICE FOR HIGH FREQUENCY
F1 1
Ratings Table
Standard
<
>
Rated
Capacitance
(µF)
Leakage
Current
Disspation
Factor
(%@120Hz)
Rated Volt
(V)
Case
code
ESR
(mΩ@100kHz)
Rated Ripple
(Arms@100kHz)
Part Number
(
A)
µ
F110E107MDL
F110E227MDL
F110E607MFK
F110E128MFK
F110G476MDL
F110G107MDL
F110G807MFK
F110J476MDL
F110J607MFK
3.5
3.5
6.3
6.3
3.5
3.5
6.3
3.5
6.3
0100
0220
0600
1200
0047
0100
0800
0047
0600
D
D
F
025
055
150
300
019
040
320
030
378
05
05
10
10
05
05
10
05
10
20.0
20.0
05.0
05.0
20.0
20.0
05.0
20.0
05.0
2.5
F
D
D
F
4.0
6.3
D
F
Low ESR
<
>
Rated
Capacitance
(µF)
Leakage
Current
Disspation
Factor
(%@120Hz)
Rated Volt
(V)
Case
code
ESR
Rated Ripple
Part Number
(mΩ@300kHz) (Arms@300kHz)
(
A)
µ
0
F110E227MDLAH1
F110E128MFKAH3
F110G107MDLAH1
F110J476MDLAH1
0
0
04.5
11.5
04.0
04.0
220
D
F
55
5
12.0
2.5
0
1.5
1200
300
10
.0
4
0
0
0
0
0
100
D
D
40
30
5
5
15.0
15.0
00
47
6.3
Layout Land Pattern (Example)
(mm)
(mm)
Case
D
a
5.5
14
b
1.4
1.8
b
1.2
1.8
c
0.5
1.2
c
1.9
6.6
Case
a
5.5
14
b
1.0
1.8
b
4.3
10.2
c
0.6
1.2
D
F
F
Frequency characteristic
The characteristics are measured by a network
analyzer and converted from S21 to impedance.
100
6.3V - 47µF (D)
10
2.5V-220µF(D)
4V - 100µF (D)
2.5V - 220µF (D)
1
2.5V-1200µF(D)
2.5V - 1200µF (F)
0.1
100k
1M
10M
100M
Frequency (Hz)
1G
10G
Notice The graph illustrates representative data. Please use this for reference only.
<
>
CAT.8100Y
相关型号：
©2020 ICPDF网 联系我们和版权申明