UEP-3.3-6000-D48_技术文档

Single Output UEP Models

Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s

FEATURES

PRODUCT OVERVIEW

The UEP Series DC/DC Converters deliver

the most power/current (up to 30W/6Amps)

from a 1" x 2" package. And because of their

footprint compatibility, they can be used as

drop in replacements for their bigger brothers,

the standard 2" x 2" and 1.6" x 2" devices,

commonly used in the industry.

n

Choice of 3 input ranges:

10-18V, 18-36V, 36-75V

n

Models Include

3.3V @ 4.5A or 6A

5V @ 3.5A or 6A

15V @ 1.2A

12V @ 1.4A

By combining a high-frequency (340kHz),

high-efﬁciency (to 89%), synchronous-rectiﬁer

topology with the newest components and

time-tested, fully automated, SMT-on-pcb

construction, these UEP Models are able

to bring you 15-30W in the standard 2" x 1"

package from which most competitors can

only get 5-10W. All UEP’s deliver their full

output power over ambient temperature

ranges from –40°C to as high as +70°C

(model and input voltage dependent) without

heat sinks or supplemental forced-air cooling.

Devices derate to +100°C.

Output voltages are 3.3, 5, 12 or 15 Volts.

Input voltage ranges are 10-18V (“D12”

models), 18-36V (“D24” models) or 36-75V

(“D48”) models. All models feature input pi

ﬁlters, input undervoltage and overvoltage

lockout, input reverse-polarity protection,

output overvoltage protection, output current

n

Guaranteed efﬁciencies to 89%

n

15-30 Watts in 1" x 2" package

n

340kHz synchronous-rectiﬁer topologies

n

–40 to +60/70°C ambient w/o derating

n

Fully isolated (1500Vdc); I/O protected

n

Trim and On/Off Control

n

limiting, and continuous short-circuit protection.

Standard features also include on/off control

and output-trim. All models are certiﬁed to

IEC950, UL1950 and EN60950 safety require-

ments for OPERATIONAL insulation. “D48”

models (36-75V inputs) are CE marked.

UEP Series DC/DC’s are packaged

in low-cost, light-weight, diallyl phthalate

(UL94V-0 rated) plastic packages with stand-

offs. EMC compliance is achieved via a low-

noise design rather than through expensive

metal shielding.

UL1950/EN60950 certiﬁed

n

CE mark (75VIN models)

For full details go to

www.murata-ps.com/rohs

+INPUT

(1)

+OUTPUT

(4)

SWITCH

CONTROL

➀

–OUTPUT

(5)

➀

–INPUT

(2)

PWM

CONTROLLER

OPTO

ISOLATION

REFERENCE &

ERROR AMP

TRIM

(6)

UVLO & OVLO

COMPARATORS

ON/OFF

CONTROL

(3)

➀

3.3V and 5V-output models use the synchronous-rectiﬁer conﬁguration shown above.

12V and 15V-output models employ a standard, diode-rectiﬁcation architecture.

Figure 1. Simpliﬁed Schematic

Typical topology is shown.

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MDC_UEP Models.A02 Page 1 of 11

Single Output UEP Models

Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s

Performance Speciﬁcations and Ordering Guide ➀

Output

R/N (mVp-p)

Max.

Input

Package

(Case,

Pinout)

Regulation (Max.)

Efﬁciency

Vo u t

(Volts)

Io u t

(mA)

Vin Nom.

(Volts)

Range

(Volts)

Vo u t

(mA)

Model

Typ.

85

Line

0.2ꢀ

Load ➂

0.5ꢀ

0.3ꢀ

0.5ꢀ

0.3ꢀ

0.5ꢀ

Min.

Typ.

84.5ꢀ

87.5ꢀ

88ꢀ

UEP-3.3/4500-D12

UEP-3.3/4500-D24

UEP-3.3/4500-D48

UEP-3.3/6000-D48

UEP-5/3500-D12

UEP-5/3500-D24

UEP-5/3500-D48

UEP-5/6000-D48

UEP-12/1400-D12

UEP-12/1400-D24

UEP-12/1400-D48

UEP-15/1200-D12

UEP-15/1200-D24

3.3

5

4500

6000

3500

6000

1400

1200

100

12

24

48

12

24

48

12

24

48

12

24

10-18

18-36

36-75

10-18

18-36

36-75

10-18

18-36

36-75

10-18

18-36

80/1490

50/730

35/360

40/470

120/1760

65/850

40/430

35/710

60/1650

45/800

20/400

60/1760

45/860

83.5ꢀ

85.5ꢀ

86ꢀ

C15, P21

84ꢀ

86ꢀ

5

86ꢀ

88ꢀ

5

86ꢀ

88ꢀ

5

88ꢀ

91ꢀ

12

15

82.5ꢀ

85ꢀ

87ꢀ

85ꢀ

87ꢀ

82.5ꢀ

85ꢀ

87ꢀ

➀ Typical at TA = +25°C under nominal line voltage and full-load conditions, unless otherwise noted.

➁ Ripple/Noise (R/N) is tested/specifed over a 20MHz bandwidth. All models are speciﬁed with no

external input/output capacitors.

➂ Load regulation is speciﬁed over no load to 100ꢀ load conditions for 3.3 and 5Vo u t models, 25mA to

100ꢀ load conditions for 12 and 15 Vo u t models.

➃ Nominal line voltage, no-load/full-load conditions.

PART NUMBER STRUCTURE

MECHANICAL SPECIFICATIONS

2.00

(50.80)

U EP - 3.3 / 4500 - D48 N - C

PLASTIC CASE

0.49

(12.45)

Case C15

ROHS-6

Hazardous

Output Conﬁguration:

Substance

STANDOFF

0.020 (0.51)

0.040 0.001 DIA.

(1.016 0.025)

U = Unipolar

Compliance

0.20 MIN

(5.08)

External Pinout

N Sufﬁx

1.800

(45.72)

0.10

(2.54)

Available for 12Vo u t

and 15Vo u t Models

1

2

4

5

Nominal Output Voltage:

3.3, 5, 12 or 15 Volts

0.800

(20.32)

0.600

(15.24)

1.00

(25.40)

Input Voltage Range:

0.400

(10.16)

0.400

(10.16)

D12 = 10-18 Volts (12V nominal)

D24 = 18-36 Volts (24V nominal)

D48 = 36-75 Volts (48V nominal)

3

6

BOTTOM VIEW

0.100

(2.54)

0.10

Maximum Output Current

in mA

(2.54)

DIMENSIONS ARE IN INCHES (MM)

Optional Functions

I/O Connections

UEP converters are designed such that the 12 and 15Vo u t models can be

conﬁgured for either positive logic on/off control (no sufﬁx) or negative logic

(“N” sufﬁx). 3.3 and 5Vo u t models are available with positive logic only (no sufﬁx).

1

Function P21

+Input

2

–Input

No Sufﬁx On/Off Control function (positive polarity) on pin 3

3

On/Off Control

+Output

–Output

Trim

N

On/Off Control function (negative polarity) on pin 3.

(12V and 15V models only.)

4

5

6

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MDC_UEP Models.A02 Page 2 of 11

Single Output UEP Models

Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s

Performance/Functional Speciﬁcations

Typical @ TA = +25°C under nominal line voltage and full-load conditions, unless noted. ➀➁

Input

Dynamic Characteristics (continued)

Input Voltage Range:

Switching Frequency

6A Models

1.2A-4.5A Models

D12 Models

D24 Models

D48 Models

10-18 Volts (12V nominal)

18-36 Volts (24V nominal)

36-75 Volts (48V nominal)

400kHz ( 20kHz)

340kHz ( 40kHz)

Environmental

Overvoltage Shutdown:

D12 Models

D24 Models

Operating Temperature (Ambient):

Without Derating ➅

With Derating

18.5-21 Volts (20V typical)

37-40 Volts (38V typical)

77-81 Volts (78.5V typical)

–40 to +60/70°C

to +100°C (See Derating Curves)

D48 Models ➆

Case Temperature:

Maximum Allowable

Start-Up Threshold: ➂

D12 Models

D24 Models

+100°C

9.3-9.8 Volts (9.6V typical)

16.5-18 Volts (17V typical)

34-36 Volts (35V typical)

Storage Temperature

–40 to +105°C

D48 Models

Physical

Undervoltage Shutdown: ➂

D12 Models

D24 Models

Dimensions

Shielding

2" x 1" x 0.51" (51 x 25 x 12.95mm)

None

7-8.5 Volts (8V typical)

15.5-17.5 Volts (16.5V typical)

32.5-35.5 Volts (34.5V typical)

Case Material

Pin Material

Weight

Diallyl phthalate, (UL94V-0 rated)

Gold-plated copper alloy with nickel underplate

1.4 ounces (39.7 grams)

D48 Models

Input Current:

Normal Operating Conditions

Standby Mode (Off, OV, UV)

See Ordering Guide

5mA

➀ All models are speciﬁed with no external input/output capacitors.

➁ See Minimum Output Loading Requirements under Technical Notes.

➂ See Technical Notes for details.

Input Filter Type

Pi

Reverse-Polarity Protection

Brief duration, 10A maximum

➃ The On/Off Control is designed to be driven with open-collector logic or the application of appro-

priate voltages (referenced to –Input (Pin 2)). Applying a voltage to the On/Off Control pin when

no input voltage is applied to the converter may cause permanent damage. See Technical Notes.

➄ Output noise may be further reduced with the addition of external output capacitors. See Technical

Notes.

On/Off Control (Optional, Pin 3): ➃

D12, D24, & D48 Models

On = open or 13V - +VIN, IIN = 50µA max.

Off = 0-0.8V, IIN = 1mA max.

On = 0-0.5V, IIN = 50µA max.

D12N, D24N, & D48N Models

Off = open or 2.4-10V, IIN = 3.7mA max.

➅ Operating temperature range without derating is model and input-voltage dependent. See

Temperature Derating.

Output

➆ UEP-3.3/600-D48 and UEP-5/6000-D48 do not have overvoltage shutdown. See Absolute

Maximum Ratings for allowable input voltages.

VOUT Accuracy (50ꢀ load):

1.5ꢀ, maximum

Minimum Loading: ➁

3.3V/5V Outputs

12V/15V Outputs

No load

25mA

Absolute Maximum Ratings

Input Voltage:

Continuous:

Ripple/Noise (20MHz BW) ➀ ➄

Line/Load Regulation

Efﬁciency

See Ordering Guide

D12 Models

D24 Models

D48 Models

22 Volts

44 Volts

88 Volts

Isolation Voltage:

Input-to-Output

1500Vdc minimum

470pF

Transient (100msec):

D12 Models

D24 Models

Isolation Capacitance

Isolation Resistance

22 Volts

44 Volts

88 Volts

100MW

D48 Models

Current Limit Inception: ➂

6A Models

4.5A Models

3.5A Models

1.4A Models

1.2A Models

Input Reverse-Polarity Protection

Current must be <10 Amps. Brief duration

only. Fusing recommended.

7-8 Amps

5.5-7 Amps (6.25 Amps typ.)

5.5-6 Amps (5.25 Amps typ.)

1.9-2.7 Amps (2.3 Amps typ.)

1.5-2.1 Amps (1.8 Amps typ.)

Output Overvoltage Protection:

3.3V Outputs

5V/12V/15V Outputs

4.5 Volts, unlimited duration

6.8/15/18 Volts, unlimited duration

Short Circuit: ➂

Average Current

Hiccup, indeﬁnite

3 Amps maximum

Output Current

Hiccup. Devices can withstand sustained

output short circuits without damage.

VOUT Trim Range ➂

5ꢀ

Case Temperature

+100°C

Overvoltage Protection ➂

Temperature Coefﬁcient

Zener/transorb clamp, magnetic feedback

0.02ꢀ per °C.Dynamic Characteristics

Storage Temperature

–40 to +105°C

+300°C

Lead Temperature (soldering, 10 sec.)

Dynamic Characteristics

These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term

reliability. Proper operation under conditions other than those listed in the Performance/Functional

Speciﬁcations Table is not implied.

Transient Response (50-100ꢀ load)

300µsec max. to 1.5ꢀ of ﬁnal value

Start-Up Time: ➂

VIN to VOUT

50msec

30msec

On/Off to VOUT

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MDC_UEP Models.A02 Page 3 of 11

Single Output UEP Models

Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s

4

TECHNICAL NOTES

1

2

3

+OUTPUT

TRIM

+INPUT

–INPUT

Floating Outputs

Since these are isolated DC/DC converters, their outputs are “ﬂoating.” Design-

ers will usually use the –Output (pin 5) as the ground/return of the load circuit.

You can, however, use the +Output (pin 4) as ground/return to effectively

reverse the output polarity.

6

5

20kΩ

5-22

LOAD

Turns

ON/OFF

CONTROL

–OUTPUT

Minimum Output Loading Requirements

3.3 and 5V models employ a synchronous-rectiﬁer design topology. All models

regulate within spec and are stable under no-load conditions. 12/15V models

employ a traditional forward, diode-rectiﬁcation architecture and require 25mA

loading to achieve their listed regulation specs. Operation under 25mA load

conditions will not damage the 12/15V devices; however they may not meet all

listed speciﬁcations.

Figure 2.Trim Connections Using A Trim Pot

4

1

2

3

+OUTPUT

+INPUT

RTRIM DOWN

6

5

–INPUT

TRIM

LOAD

Filtering and Noise Reduction

All UEP Series DC/DC Converters achieve their rated ripple and noise speci-

ﬁcations with no external input/output capacitors. In critical applications,

input/output noise may be further reduced by installing external I/O caps.

Input capacitors should be selected for bulk capacitance, low ESR and high

rms-ripple-current ratings. Output capacitors should be selected for low ESR

and appropriate frequency response. All caps should have appropriate voltage

ratings and be mounted as close to the converters as possible.

ON/OFF

CONTROL

–OUTPUT

Figure 3.Trim Connections To Decrease Output Voltage Using Fixed Resistors

4

1

2

3

+OUTPUT

TRIM

The most effective combination of external I/O capacitors will be a function

of load and layout conditions. Our Applications Engineers can recommend

potential solutions and discuss the possibility of our modifying a given device’s

internal ﬁltering to meet your speciﬁc requirements. Contact our Applications

Engineering Group for additional details.

+INPUT

–INPUT

6

LOAD

RTRIM UP

ON/OFF

CONTROL

5

–OUTPUT

Input Fusing

Certain applications and/or safety agencies may require the installation of

fuses at the inputs of power conversion components. Fuses should also be

used if the possibility of sustained, non-current-limited, input-voltage polarity

reversals exists. For DATEL UEP Series DC/DC Converters, you should use

slow-blow type fuses with values no greater than the following.

Figure 4.Trim Connections To Increase Output Voltage Using Fixed Resistors

Model

Trim Equation

2.49(VO – 1.27)

UEP-3.3/4500-D12

UEP-3.3/4500-D24

UEP-3.3/4500-D48

UEP-3.3/6000-D48

–16.9

–15

RT_DOWN(kΩ) =

3.3 – V^O

VIN Range

Fuse Value

3.16

D12 Models

D24 Models

3 Amps

2 Amps

1 Amp

2 Amp

–16.9

RT_UP(kΩ) =

V^O– 3.3

D48 Models (1.2-4.5A)

D48 Models (6A)

2.49(VO – 2.527)

5 – V^O

UEP-5/3500-D12

UEP-5/3500-D24

UEP-5/3500-D48

UEP-5/6000-D48

RT_DOWN(kΩ) =

RT_UP(kΩ) =

6.292

Trimming Output Voltages

–15

VO – 5

These converters have a trim capability (pin 6) that allows users to adjust the

output voltage 5ꢀ. Adjustments to the output voltage can be accomplished

via a trim pot, Figure 2, or a single ﬁxed resistor as shown in Figures 3 and 4.

A single ﬁxed resistor can increase or decrease the output voltage depend-

ing on its connection. Fixed resistors should have an absolute TCR less than

100ppm/°C to minimize sensitivity to changes in temperature.

6.34(VO – 5.714)

12 – V^O

–49.9

–63.4

RT_DOWN(kΩ) =

RT_UP(kΩ) =

RT_DOWN(kΩ) =

RT_UP(kΩ) =

UEP-12/1400-D12

UEP-12/1400-D24

UEP-12/1400-D48

36.23

–49.9

V^O– 12

7.87(VO – 7.136)

15 – V^O

UEP-15/1200-D12

UEP-15/1200-D24

UEP-15/1200-D48

A single resistor connected from the Trim (pin 6) to the +Output (pin 4), see

Figure 3, will decrease the output voltage. A resistor connected from the Trim

(pin 6) to –Output (pin 5) will increase the output voltage.

56.16

–63.4

V^O– 15

Trim adjustment greater than 5ꢀ can have an adverse effect on the converter's

performance and is not recommended.

Accuracy of adjustment is subject to tolerances of resistor values and factory-

adjusted output accuracy. Vo = desired output voltage.

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MDC_UEP Models.A02 Page 4 of 11

Single Output UEP Models

Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s

Input Overvoltage/Undervoltage Shutdown and Start-Up Threshold

Under normal start-up conditions, devices will not begin to regulate until the

ramping-up input voltage exceeds the Start-Up Threshold Voltage (35V for

"D48" models). Once operating, devices will not turn off until the input voltage

drops below the Undervoltage Shutdown limit (34V for "D48" models). Subse-

quent re-start will not occur until the input is brought back up to the Start-Up

Threshold. This built in hysteresis prevents any unstable on/off situations from

occurring at a single input voltage.

+INPUT

1

3

ON/OFF

CONTROL

–INPUT

2

Input voltages exceeding the input overvoltage shutdown speciﬁcation listed in

the Performance/Functional Speciﬁcations will cause the device to shutdown. A

built-in hysteresis of 0.6 to 1.6 Volts for all models will not allow the converter

to restart until the input voltage is sufﬁciently reduced.

Figure 3. Driving the Negative Polarity On/Off Control Pin

Dynamic control of the remote on/off function is best accomplished with a

mechanical relay or an open-collector/open-drain drive circuit (optically iso-

lated if appropriate). The drive circuit should be able to sink appropriate current

(see Performance Specs) when activated and withstand appropriate voltage

when deactivated.

The two 6 Amp models do not feature overvoltage shutdown and withstand

surges to 100V without shutting down. For custom overvoltage protection,

contact DATEL.

Input Reverse-Polarity Protection

If the input-voltage polarity is accidentally reversed, an internal diode will

become forward biased and likely draw excessive current from the power

source. If the source is not current limited (<10A) nor the circuit appropriately

fused, it could cause permanent damage to the converter.

Applying an external voltage to pin 3 when no input power is applied to the

converter can cause permanent damage to the converter.

Start-Up Time

The VIN to VOUT start-up time is the interval of time where the input voltage

crosses the turn-on threshold point, and the fully loaded output voltage enters

and remains within its speciﬁed accuracy band. Actual measured times will

vary with input source impedance, external input/output capacitance, and load.

The UEP Series implements a soft start circuit that limits the duty cycle of the

PWM controller at power up, thereby limiting the Input Inrush current.

On/Off Control

The input-side, remote On/Off Control function (pin 3) can be ordered to oper-

ate with either polarity (negative polarity available for 12 and 15 Volt models

only). Positive-polarity devices (standard, no part-number sufﬁx) are enabled

when pin 3 is left open or is pulled high (+13V to VIN applied with respect to

–Input, pin 2, (see Figure 2). Positive-polarity devices are disabled when pin 3

is pulled low (0-0.8V with respect to –Input). Negative-polarity devices are off

when pin 3 is open or pulled high (+2.4V to +10V), and on when pin 3 is pulled

low (0-0.5V). See Figure 3.

The On/Off Control to VOUT start-up time assumes the converter has its nominal

input voltage applied but is turned off via the On/Off Control pin. The speciﬁca-

tion deﬁnes the interval between the time at which the converter is turned on

and the fully loaded output voltage enters and remains within its speciﬁed

accuracy band. Similar to the VIN to VOUT start-up, the On/Off Control to VOUT

start-up time is also governed by the internal soft start circuitry and external

load capacitance.

+INPUT

1

3

200k

13V CIRCUIT

5V CIRCUIT

Current Limiting

ON/OFF

When output increases to 120ꢀ to 190ꢀ of the rated output current, the DC/DC

converter will go into a current limiting mode. In this condition the output

voltage will decrease proportionately with increases in output current, thereby

maintaining a somewhat constant power dissipation. This is commonly

referred to as power limiting. Current limit inception is deﬁned as the point

where the full-power output voltage falls below the speciﬁed tolerance. See

Performance/Functional Speciﬁcations. If the load current being drawn from

the converter is signiﬁcant enough, the unit will go into a short circuit condi-

tion. See “Short Circuit Condition.”

CONTROL

–INPUT

2

Figure 2. Driving the Positive Polarity On/Off Control Pin

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MDC_UEP Models.A02 Page 5 of 11

Single Output UEP Models

Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s

Short Circuit Condition

Typical Performance Curves

When a converter is in current limit mode the output voltages will drop as the

output current demand increases. If the output voltage drops too low, the

magnetically coupled primary side voltages will also drop, thereby shutting

down the PWM controller.

Temperature Derating Curves for UEP-3.3/4500 Output Models

17.5

Following a time-out period, the PWM will restart, causing the output voltage to

begin ramping to its appropriate value. If the short-circuit condition persists,

another shutdown cycle will be initiated. This on/off cycling is referred to

as "hiccup" mode. The hiccup cycling reduces the average output current,

thereby preventing internal temperatures from rising to excessive levels. The

UEP is capable of enduring an indeﬁnite short circuit output condition.

VIN = 18V-27V (D24)

V^IN= 36V-48V (D48)

15

12.5

10

V^IN= 18V-30V (D24)

V^IN= 36V-60V (D48)

Thermal Shutdown

7.5

These UEP converters are equipped with Thermal Shutdown Circuitry. If envi-

ronmental conditions cause the internal temperature of the DC/DC converter

rises above the designed operating temperature (typically 118°C case), a

precision temperature sensor will power down the unit. When the internal

temperature decreases below the threshold of the temperature sensor the unit

will self start.

V^IN= 12V (D12)

V^IN= 18V-36V (D24)

V^IN= 36V-75V (D48)

5

2.5

0

–40

0

40

45

50

55

60

65

70

75

80

85

90

95

100

Output Overvoltage Protection

Ambient Temperature ( C)

°

Output voltages are monitored for an overvoltage condition via magnetic

coupling to the primary side. If the output voltage should rise to a level which

could be damaging to the load circuitry, the sensing circuitry will power down

the PWM controller causing the output voltages to decrease. Following a

time-out period the PWM will restart, causing the output voltages to ramp to

their appropriate values. If the fault condition persists, and the output voltage

again climbs to excessive levels, the overvoltage circuitry will initiate another

shutdown cycle. This on/off cycling is referred to as “hiccup” mode.

5%0ꢀꢁꢂꢁꢃꢄꢅꢆꢆꢀ$ꢇꢄ %FFICIENCY VSꢂ ,INE 6OLTAGE AND ,OAD #URRENT

ꢀꢁ

ꢂꢃ

ꢂꢁ

ꢄꢃ

ꢄꢁ

ꢅꢃ

ꢅꢁ

ꢃꢃ

ꢃꢁ

ꢆꢃ

ꢆꢁ

6). ꢁ ꢂꢃ6

6

). ꢁ ꢄꢅ6

6

). ꢁ ꢆꢇ6

ꢁꢇꢆ

ꢁꢇꢀꢈ

ꢈꢇꢆꢉ

ꢈꢇꢀꢆ

ꢊꢇꢆꢃ

ꢊꢇꢀꢅ

ꢉꢇꢆꢂ

ꢉꢇꢀꢀ

ꢆꢇꢃ

,OAD #URRENT ꢈ!MPSꢉ

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MDC_UEP Models.A02 Page 6 of 11

Single Output UEP Models

Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s

Typical Performance Curves

Temperature Derating Curves for UEP-3.3/6000-D48

UEP-3.3/4500-D48 Efficiency vs. Line Voltage and Load Current

21

18

15

12

9

90

85

80

75

70

65

60

55

50

45

VIN = 36V

V

IN = 36V

VIN = 75V

V

IN = 48V

V^IN= 48V

6

V

IN = 75V

3

0

0.4

0.91

1.43

1.94

2.45

2.96

3.48

3.99

4.5

–40

0

40

45

50

55

60

65

70

75

80

85

90

95

100

Load Current (Amps)

Ambient Temperature ( C)

˚

UEP-3.3/6000-D48 Efficiency vs. Line Voltage and Load Current

5%0ꢀꢁꢂꢁꢃꢄꢅꢆꢆꢀ$ꢇꢈ %FFICIENCY VSꢂ ,INE 6OLTAGE AND ,OAD #URRENT

90

85

80

75

70

65

60

55

50

45

ꢀꢁ

ꢂꢃ

ꢂꢁ

ꢄꢃ

ꢄꢁ

ꢅꢃ

ꢅꢁ

ꢃꢃ

ꢃꢁ

ꢆꢃ

ꢆꢁ

V

IN = 36V

6

). ꢁ ꢂꢃ6

V

IN = 48V

6

). ꢁ ꢂꢄ6

V

IN = 75V

6

). ꢁ ꢂꢅ6

1

2

3

4

5

6

ꢁꢇꢆ

ꢁꢇꢀꢈ

ꢈꢇꢆꢉ

ꢈꢇꢀꢆ

ꢊꢇꢆꢃ

ꢊꢇꢀꢅ

ꢉꢇꢆꢂ

ꢉꢇꢀꢀ

ꢆꢇꢃ

Load Current (Amps)

,OAD #URRENT ꢉ!MPSꢊ

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MDC_UEP Models.A02 Page 7 of 11

7

Single Output UEP Models

Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s

Typical Performance Curves

Temperature Derating Curves for UEP-5/6000-D48

Temperature Derating Curves for UEP-5/3500 Output Models

32

28

24

20

16

12

8

20

17.5

15

VIN = 18V-27V (D24)

V^IN= 36V-48V (D48)

VIN = 36V-48V

12.5

10

V^IN= 18V-30V (D24)

V^IN= 36V-60V (D48)

7.5

5

V^IN= 75V

V^IN= 12V (D12)

V^IN= 18V-36V (D24)

V^IN= 36V-75V (D48)

4

2.5

0

–40

0

40

45

50

55

60

65

70

75

80

85

90

95

100

–40

0

40

45

50

55

60

65

70

75

80

85

90

95

100

Ambient Temperature ( C)

˚

°

5%0ꢀꢁꢂꢃꢁꢄꢄꢀ$ꢅꢆ %FFICIENCY VSꢇ ,INE 6OLTAGE AND ,OAD #URRENT

ꢀꢁ

ꢂꢃ

ꢂꢁ

ꢄꢃ

ꢄꢁ

ꢅꢃ

ꢅꢁ

ꢃꢃ

ꢃꢁ

ꢆꢃ

ꢆꢁ

ꢂꢃ

ꢂꢁ

ꢄꢃ

ꢄꢁ

ꢅꢃ

ꢅꢁ

ꢃꢃ

ꢃꢁ

ꢆꢃ

ꢆꢁ

6

). ꢁ ꢂꢃ6

6

). ꢁ ꢂꢃ6

6

). ꢁ ꢄꢅ6

6

). ꢁ ꢂꢄ6

6

). ꢁ ꢆꢇ6

6

). ꢁ ꢂꢅ6

ꢁꢇꢈ

ꢁꢇꢄ

ꢉꢇꢉ

ꢉꢇꢃ

ꢉꢇꢀ

ꢊꢇꢈ

ꢊꢇꢄ

ꢈꢇꢉ

ꢈꢇꢃ

ꢁꢇꢈ

ꢁꢇꢄ

ꢉꢇꢉ

ꢉꢇꢃ

ꢉꢇꢀ

ꢊꢇꢈ

ꢊꢇꢄ

ꢈꢇꢉ

ꢈꢇꢃ

,OAD #URRENT ꢈ!MPSꢉ

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MDC_UEP Models.A02 Page 8 of 11

8

Single Output UEP Models

Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s

Typical Performance Curves

Temperature Derating Curves for 12V Output Models

UEP-5/3500-D48 Efficiency vs. Line Voltage and Load Current

18

16

14

12

10

8

90

85

80

75

70

65

60

55

50

45

40

VIN = 18V-27V (D24)

V^IN= 36V-48V (D48)

V

IN = 36V

V^IN= 18V-30V (D24)

V^IN= 36V-60V (D48)

V

IN = 48V

V^IN= 12V (D12)

6

V^IN= 18V-36V (D24)

V^IN= 36V-75V (D48)

V

IN = 75V

4

2

0

0.3

0.7

1.1

1.5

1.9

2.3

2.7

3.1

3.5

–40

0

40

45

50

55

60

65

70

75

80

85

90

95

100

Load Current (Amps)

Ambient Temperature ( C)

˚

UEP-5/6000-D48 Efficiency vs. Line Voltage and Load Current

5%0ꢀꢁꢂꢃꢁꢄꢅꢅꢀ$ꢂꢄ %FFICIENCY VSꢆ ,INE 6OLTAGE AND ,OAD #URRENT

95

90

85

80

75

70

65

60

55

ꢀꢁ

ꢂꢃ

ꢂꢁ

ꢄꢃ

ꢄꢁ

ꢅꢃ

ꢅꢁ

ꢃꢃ

V

IN = 36V

6

). ꢁ ꢂꢃ6

V

IN = 48V

6

). ꢁ ꢄꢅ6

V

IN = 75V

6

). ꢁ ꢆꢇ6

1

2

3

4

5

6

ꢁꢆꢇꢁ

ꢁꢆꢈꢅ

ꢁꢆꢉꢊ

ꢁꢆꢃꢀ

ꢁꢆꢄꢃ

ꢁꢆꢀꢇ

ꢇꢆꢁꢅ

ꢇꢆꢈꢉ

ꢇꢆꢉꢁ

Load Current (Amps)

,OAD #URRENT ꢇ!MPSꢈ

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MDC_UEP Models.A02 Page 9 of 11

Single Output UEP Models

Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s

Typical Performance Curves

5%0ꢀꢁꢂꢃꢁꢄꢅꢅꢀ$ꢁꢂ %FFICIENCY VSꢆ ,INE 6OLTAGE AND ,OAD #URRENT

5%0ꢀꢁꢂꢃꢁꢄꢅꢅꢀ$ꢄꢆ %FFICIENCY VSꢇ ,INE 6OLTAGE AND ,OAD #URRENT

ꢀꢁ

ꢂꢃ

ꢂꢁ

ꢄꢃ

ꢄꢁ

ꢅꢃ

ꢅꢁ

ꢃꢃ

ꢀꢁ

ꢂꢃ

ꢂꢁ

ꢄꢃ

ꢄꢁ

ꢅꢃ

ꢅꢁ

ꢃꢃ

6

). ꢁ ꢂꢃ6

6

). ꢁ ꢂꢃ6

6

). ꢁ ꢄꢅ6

6

). ꢁ ꢂꢄ6

6

). ꢁ ꢂꢅ6

6

). ꢁ ꢆꢇ6

ꢁꢆꢇꢁ

ꢁꢆꢈꢅ

ꢁꢆꢉꢊ

ꢁꢆꢃꢀ

ꢁꢆꢄꢃ

ꢁꢆꢀꢇ

ꢇꢆꢁꢅ

ꢇꢆꢈꢉ

ꢇꢆꢉꢁ

ꢁꢆꢇꢁ

ꢁꢆꢈꢉ

ꢁꢆꢊꢂ

ꢁꢆꢃꢇ

ꢁꢆꢅꢃ

ꢁꢆꢄꢀ

ꢁꢆꢀꢊ

ꢇꢆꢁꢅ

ꢇꢆꢈ

,OAD #URRENT ꢇ!MPSꢈ

,OAD #URRENT ꢈ!MPSꢉ

UEP-12/1400-D48 Efficiency vs. Line Voltage and Load Current

5%0ꢀꢁꢂꢃꢁꢄꢅꢅꢀ$ꢁꢄ %FFICIENCY VSꢆ ,INE 6OLTAGE AND ,OAD #URRENT

90

85

80

75

70

65

60

55

50

45

ꢀꢁ

ꢂꢃ

ꢂꢁ

ꢄꢃ

ꢄꢁ

ꢅꢃ

ꢅꢁ

ꢃꢃ

V

IN = 36V

6

). ꢁ ꢂꢃ6

V

IN = 48V

6

). ꢁ ꢂꢄ6

V

IN = 75V

6

). ꢁ ꢂꢅ6

0.10

0.26

0.43

0.59

0.75

0.91

1.06

1.24

1.40

ꢁꢆꢇꢁ

ꢁꢆꢈꢉ

ꢁꢆꢊꢂ

ꢁꢆꢃꢇ

ꢁꢆꢅꢃ

ꢁꢆꢄꢀ

ꢁꢆꢀꢊ

ꢇꢆꢁꢅ

ꢇꢆꢈ

Load Current (Amps)

Temperature Derating Curves for 15V Output Models

,OAD #URRENT ꢇ!MPSꢈ

UEP-15/1200-D48 Efficiency vs. Line Voltage and Load Current

20

90

85

80

75

70

65

60

55

50

18

16

14

12

10

8

VIN = 18V-27V (D24)

V^IN= 36V-48V (D48)

V^IN= 18V-30V (D24)

V^IN= 36V-60V (D48)

VIN = 36V

V^IN= 12V (D12)

VIN = 48V

6

V^IN= 18V-36V (D24)

V^IN= 36V-75V (D48)

4

VIN = 75V

2

0

–40

0

40

45

50

55

60

65

70

75

80

85

90

95

100

0.10

0.24

0.38

0.51

0.65

0.79

0.93

1.06

1.2

Ambient Temperature ( C)

˚

Load Current (Amps)

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MDC_UEP Models.A02 Page 10 of 11

1 5 - 3 0 W , S I N G L E O U T P U T D C / D C C O N V E R T E R S

Single Output UEP Models

Ultra-High Density, 2" x 1", 1.2-6 Amp,15-30 Watt DC/DC’s

Typical Performance Curves

Output Ripple and Noise (PARD)

(VIN = nominal, 3.3V @ 4.5A, no external capacitors.)

Output Ripple and Noise (PARD)

(VIN = nominal, 12V @ 1.4A, no external capacitors.)

20mV/div, 20MHz BW

Output Ripple and Noise (PARD)

(VIN = nominal, 5V @ 3.5A, no external capacitors.)

Output Ripple and Noise (PARD)

(VIN = nominal, 15V @ 1.2A, no external capacitors.)

20mV/div, 20MHz BW

USA:

Canada: Toronto, Tel: (866) 740 1232, email: toronto@murata-ps.com

UK: Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com

Tucson (AZ), Tel: (800) 547 2537, email: sales@murata-ps.com

France: Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com

Germany: München, Tel: +49 (0)89-544334-0, email: ped.munich@murata-ps.com

Murato Power Solutions, Inc.

11 Cabot Boulevard, Mansﬁeld, MA 02048-1151 U.S.A.

Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356

Japan:

Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com

Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com

Website: www.murata-ps.jp

China:

Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com

Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com

www.murata-ps.com

ISO 9001 REGISTERED

email: sales@murata-ps.com

DS-0502B

2/14/08

Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other

technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not

imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Speciﬁcations are subject to change

without notice.

www.murata-ps.com

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MDC_UEP Models.A02 Page 11 of 11


型号：	UEP-3.3-6000-D48
厂家：	muRata
描述：	Single Output UEP Models 单输出模式UEP
文件：	总11页 (文件大小：821K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

UEP-3.3-6000-D48 [MURATA]

相关型号：

UEP-3.3/4500-D12

UEP-3.3/4500-D24

UEP-3.3/4500-D48

UEP-3.3/6000-D48

UEP-5-3500-D12

UEP-5-3500-D24

UEP-5-3500-D48

UEP-5-6000-D48

UEP-5/3500-D12

UEP-5/3500-D24

UEP-5/3500-D24-C

UEP-5/3500-D48