RHS7J2H332J2M2H01A [MURATA]
汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C];型号: | RHS7J2H332J2M2H01A |
厂家: | muRata |
描述: | 汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] 医疗 医疗器械 |
文件: | 总15页 (文件大小:648K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Reference Specification
200℃ Operation Leaded MLCC for Automotive with AEC-Q200
RHS Series
Product specifications in this catalog are as of Mar. 2022, and are subject to change or
obsolescence without notice.
Please consult the approval sheet before ordering.Please read rating and Cautions first.
Reference only
CAUTION
1. OPERATING VOLTAGE
When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p
value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the
voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be generated
for a transit period because of resonance or switching. Be sure to use a capacitor within rated voltage
containing these irregular voltage.
When DC-rated capacitors are to be used in input circuits from commercial power source (AC filter),
be sure to use Safety Recognized Capacitors because various regulations on withstand voltage or
impulse withstand established for each equipment should be taken into considerations.
Voltage
DC Voltage
DC+AC Voltage
AC Voltage
Pulse Voltage(1)
Pulse Voltage(2)
Positional
Vo-p
Vp-p
Vo-p
Vp-p
Vp-p
Measurement
2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT
Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range.
Be sure to take into account the heat generated by the capacitor itself.
When the capacitor is used in a high-frequency current, pulse current or the like, it may have the self-
generated heat due to dielectric-loss. In case of Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.),
applied voltage should be the load such as self-generated heat is within 20 °C on the condition of
atmosphere temperature 25 °C. Please contact us if self-generated heat is occurred with Class 1
capacitors (Temp.Char. : C0G,U2J,X8G, etc.). When measuring, use a thermocouple of small thermal
capacity-K of Φ0.1mm and be in the condition where capacitor is not affected by radiant heat of other
components and wind of surroundings. Excessive heat may lead to deterioration of the capacitor’s
characteristics and reliability.
3. FAIL-SAFE
Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that
may be caused by the abnormal function or the failure of our product.
4. OPERATING AND STORAGE ENVIRONMENT
The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store
capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the
like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify
that these processes do not affect product quality by testing the performance of a cleaned, bonded or
molded product in the intended equipment. Store the capacitors where the temperature and relative
humidity do not exceed 5 to 40 °C and 20 to 70%. Use capacitors within 6 months.
5. VIBRATION AND IMPACT
Do not expose a capacitor or its leads to excessive shock or vibration during use.
6. SOLDERING
When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the
capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may
result in thermal shocks that can crack the ceramic element.
7. BONDING AND RESIN MOLDING, RESIN COAT
In case of bonding, molding or coating this product, verify that these processes do not affect the quality
of capacitor by testing the performance of a bonded or molded product in the intended equipment.
In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins
containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer
coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short
circuit.
The variation in thickness of adhesive or molding resin may cause a outer coating resin cracking and/or
ceramic element cracking of a capacitor in a temperature cycling.
8. TREATMENT AFTER BONDING AND RESIN MOLDING, RESIN COAT
When the outer coating is hot (over 100 °C) after soldering, it becomes soft and fragile.
So please be careful not to give it mechanical stress.
EGLEDMNO03
1/14
Reference only
Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial
dispersion when the product is used.
9. LIMITATION OF APPLICATIONS
Please contact us before using our products for the applications listed below which require especially
high reliability for the prevention of defects which might directly cause damage to the third party’s life,
body or property.
1. Aircraft equipment
2. Aerospace equipment
3. Undersea equipment
5. Medical equipment
7. Traffic signal equipment
4. Power plant control equipment
6. Transportation equipment (vehicles, trains, ships, etc.)
8. Disaster prevention / crime prevention equipment
9. Data-processing equipment exerting influence on public
10. Application of similar complexity and/or reliability requirements to the applications listed in the above.
NOTICE
1. CLEANING (ULTRASONIC CLEANING)
To perform ultrasonic cleaning, observe the following conditions.
Rinse bath capacity : Output of 20 watts per liter or less.
Rinsing time : 5 min maximum.
Do not vibrate the PCB/PWB directly.
Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires.
2. SOLDERING AND MOUNTING
Insertion of the Lead Wire
• When soldering, insert the lead wire into the PCB without mechanically stressing the lead wire.
• Insert the lead wire into the PCB with a distance appropriate to the lead space.
3. CAPACITANCE CHANGE OF CAPACITORS
• Class 2 capacitors (Temp.Char. : X7R,X7S,X8L etc.)
Class 2 capacitors an aging characteristic, whereby the capacitor continually decreases its capacitance
slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on
a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant
circuit.
Please contact us if you need a detail information.
NOTE
1. Please make sure that your product has been evaluated in view of your specifications with our product
being mounted to your product.
2. You are requested not to use our product deviating from this specification.
EGLEDMNO03
2/14
Reference only
1. Application
This specification is applied to 200°C Operation Leaded MLCC RHS series
iin accordance with AEC-Q200 requirements used for Automotive Electronic equipment.
2. Rating
• Applied maximum temperature up to 200°C
Note : Maximum accumulative time to 200°C is within 2000 hours.
• Part Number Configuration
RHS
7J
2D
101
J
1
A2
Dimension Lead
(LxW) Style
H01
B
ex.)
Series
Temperature
Characteristics
Rated
Voltage
Capacitance
Capacitance
Tolerance
Individual
Specification
Package
• Series
Code
RHS
Content
Epoxy coated, 200°C max.
• Temperature Characteristics
Code Temp. Char.
Standard
Temp.
Operating
Temp. Range
Temp. Range
Temp.coef.
-55~25°C
25~125°C
125~200°C
-750+120/-347ppm/°C
-750+/-120ppm/°C
-750+347/-120ppm/°C
UNJ
7J
25°C
-55~200°C
(Murata code)
• Rated Voltage
Code
2D
2H
Rated voltage
DC200V
DC500V
When the product temperature exceeds 150°C, please use this product
within the voltage and temperature derated conditions in the figure below.
• Capacitance
The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.
ex.) In case of 101
10×101 = 100pF
TEIKAKU
3/14
Reference only
• Capacitance Tolerance
Code
J
Capacitance Tolerance
+/-5%
• Dimension (LxW)
Please refer to [ Part number list ].
• Lead Style
*Lead wire is "solder coated CP wire".
Code
A2
Lead Style
Straight type
Lead spacing (mm)
2.5+/-0.8
DG
K1
Straight taping type
Inside crimp type
2.5+0.4/-0.2
5.0+/-0.8
M2
Inside crimp taping type
5.0+0.6/-0.2
• Individual Specification
Murata’s control code.
Please refer to [ Part number list ].
• Package
Code
A
B
Package
Taping type of Ammo
Bulk type
3. Marking
Temp. char.
Capacitance
Capacitance tolerance
Rated voltage
:
:
:
:
Letter code : 2 (UNJ char.)
3 digit numbers
Code
Letter code : 6 (DC200V. Except dimension code : 1)
Letter code : 9 (DC500V)
Company name code
:
Abbreviation :
(Except dimension code : 1)
(Ex.)
Rated voltage
DC200V
DC500V
Dimension code
1
2
101J
-
103
J62
101
J92
2
TEIKAKU
4/14
Reference only
4. Part number list
Unit : mm
DC
Dimension (mm)
W1
Dimension Pack
Customer
Part Number
Rated
Volt.
(V)
Cap.
Tol.
Murata Part Number
T.C.
Cap.
(LxW)
qty.
Lead Style (pcs)
L
W
F
T
RHS7J2D101J1A2H01B
RHS7J2D151J1A2H01B
RHS7J2D221J1A2H01B
RHS7J2D331J1A2H01B
RHS7J2D471J1A2H01B
RHS7J2D681J1A2H01B
RHS7J2D102J1A2H01B
RHS7J2D152J1A2H01B
RHS7J2D222J1A2H01B
RHS7J2D332J1A2H01B
RHS7J2D472J1A2H01B
RHS7J2D682J2A2H01B
RHS7J2D103J2A2H01B
RHS7J2D101J1K1H01B
RHS7J2D151J1K1H01B
RHS7J2D221J1K1H01B
RHS7J2D331J1K1H01B
RHS7J2D471J1K1H01B
RHS7J2D681J1K1H01B
RHS7J2D102J1K1H01B
RHS7J2D152J1K1H01B
RHS7J2D222J1K1H01B
RHS7J2D332J1K1H01B
RHS7J2D472J1K1H01B
RHS7J2D682J2K1H01B
RHS7J2D103J2K1H01B
RHS7J2H101J2K1H01B
RHS7J2H151J2K1H01B
RHS7J2H221J2K1H01B
RHS7J2H331J2K1H01B
RHS7J2H471J2K1H01B
RHS7J2H681J2K1H01B
RHS7J2H102J2K1H01B
RHS7J2H152J2K1H01B
RHS7J2H222J2K1H01B
RHS7J2H332J2K1H01B
RHS7J2H472J2K1H01B
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
UNJ
200
200
200
200
200
200
200
200
200
200
200
200
100pF
150pF
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
4.2
3.5
-
-
-
-
-
-
-
-
-
-
-
-
-
2.5
2.8
1A2
1A2
1A2
1A2
1A2
1A2
1A2
1A2
1A2
1A2
1A2
2A2
2A2
1K1
1K1
1K1
1K1
1K1
1K1
1K1
1K1
1K1
1K1
1K1
2K1
2K1
2K1
2K1
2K1
2K1
2K1
2K1
2K1
2K1
2K1
2K1
2K1
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
5.5
5.5
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
4.0
4.0
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
3.3
3.3
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
220pF
330pF
470pF
680pF
1000pF
1500pF
2200pF
3300pF
4700pF
6800pF
200 10000pF
200
200
200
200
200
200
200
200
200
200
200
200
100pF
150pF
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
220pF
330pF
470pF
680pF
1000pF
1500pF
2200pF
3300pF
4700pF
6800pF
200 10000pF
500
500
500
500
500
500
500
500
500
500
500
100pF
150pF
220pF
330pF
470pF
680pF
1000pF
1500pF
2200pF
3300pF
4700pF
PNLIST
5/14
Reference only
Unit : mm
DC
Rated
Volt.
(V)
Dimension (mm)
Dimension Pack
Customer
Part Number
Cap.
Tol.
Murata Part Number
T.C.
Cap.
(LxW)
Lead Style (pcs)
H/H0
qty.
L
W
W1
F
T
RHS7J2D101J1DGH01A UNJ 200
RHS7J2D151J1DGH01A UNJ 200
RHS7J2D221J1DGH01A UNJ 200
RHS7J2D331J1DGH01A UNJ 200
RHS7J2D471J1DGH01A UNJ 200
RHS7J2D681J1DGH01A UNJ 200
RHS7J2D102J1DGH01A UNJ 200
RHS7J2D152J1DGH01A UNJ 200
RHS7J2D222J1DGH01A UNJ 200
RHS7J2D332J1DGH01A UNJ 200
RHS7J2D472J1DGH01A UNJ 200
RHS7J2D682J2DGH01A UNJ 200
100pF
150pF
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
5.5
5.5
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
3.5
-
-
-
-
-
-
-
-
-
-
-
-
-
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
3.3 20.0
3.3 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
2.8 20.0
3.3 20.0
3.3 20.0
3.3 20.0
3.3 20.0
3.3 20.0
3.3 20.0
3.3 20.0
3.3 20.0
3.3 20.0
3.3 20.0
3.3 20.0
3.3 20.0
3.3 20.0
1DG
1DG
1DG
1DG
1DG
1DG
1DG
1DG
1DG
1DG
1DG
2DG
2DG
1M2
1M2
1M2
1M2
1M2
1M2
1M2
1M2
1M2
1M2
1M2
2M2
2M2
2M2
2M2
2M2
2M2
2M2
2M2
2M2
2M2
2M2
2M2
2M2
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
1500
1500
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
4.0
4.0
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
220pF
330pF
470pF
680pF
1000pF
1500pF
2200pF
3300pF
4700pF
6800pF
RHS7J2D103J2DGH01A UNJ 200 10000pF
RHS7J2D101J1M2H01A UNJ 200
RHS7J2D151J1M2H01A UNJ 200
RHS7J2D221J1M2H01A UNJ 200
RHS7J2D331J1M2H01A UNJ 200
RHS7J2D471J1M2H01A UNJ 200
RHS7J2D681J1M2H01A UNJ 200
RHS7J2D102J1M2H01A UNJ 200
RHS7J2D152J1M2H01A UNJ 200
RHS7J2D222J1M2H01A UNJ 200
RHS7J2D332J1M2H01A UNJ 200
RHS7J2D472J1M2H01A UNJ 200
RHS7J2D682J2M2H01A UNJ 200
100pF
150pF
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
220pF
330pF
470pF
680pF
1000pF
1500pF
2200pF
3300pF
4700pF
6800pF
RHS7J2D103J2M2H01A UNJ 200 10000pF
RHS7J2H101J2M2H01A UNJ 500
RHS7J2H151J2M2H01A UNJ 500
RHS7J2H221J2M2H01A UNJ 500
RHS7J2H331J2M2H01A UNJ 500
RHS7J2H471J2M2H01A UNJ 500
RHS7J2H681J2M2H01A UNJ 500
RHS7J2H102J2M2H01A UNJ 500
RHS7J2H152J2M2H01A UNJ 500
RHS7J2H222J2M2H01A UNJ 500
RHS7J2H332J2M2H01A UNJ 500
RHS7J2H472J2M2H01A UNJ 500
100pF
150pF
220pF
330pF
470pF
680pF
1000pF
1500pF
2200pF
3300pF
4700pF
PNLIST
6/14
Reference only
5. AEC-Q200 Murata Standard Specifications and Test Methods
AEC-Q200
No.
Specification
AEC-Q200 Test Method
Test Item
Pre-and Post-Stress
Electrical Test
High
1
-
2
3
No defects or abnormalities except color
change of outer coating.
Sit the capacitor for 1000±12h at 200±5°C. Let sit for 24±2h at
*room condition, then measure.
Appearance
Temperature
Exposure
Capacitance Within ±3% or ±0.3pF
(Storage)
Change
Q
(Whichever is larger)
Q ≧ 350
I.R.
1,000MΩ min.
Temperature Appearance
Cycling
No defects or abnormalities except color
change of outer coating.
Perform the 1000 cycles according to the four heat treatments listed in
the following table. Let sit for 24±2 h at *room condition, then measure.
Capacitance Within ±5% or ±0.5pF
Step
1
2
3
4
Change
Q
(Whichever is larger)
Q ≧ 350
Temp.
(°C)
Room
Temp.
Room
Temp.
-55+0/-3
200+5/-0
I.R.
1,000MΩ min.
Time
15±3
1
15±3
1
(min.)
4
Moisture
Appearance
No defects or abnormalities.
Apply the 24h heat (25 to 65°C) and humidity (80 to 98%)
treatment shown below, 10 consecutive times.
Resistance
Capacitance Within ±5% or ± 0.5pF
Change
Q
(Whichever is larger)
Q ≧ 200
Let sit for 24±2 h at *room condition, then measure.
I.R.
500MΩ min.
5
6
Biased
Appearance
No defects or abnormalities.
Apply the rated voltage and DC1.3+0.2/-0V (add 100kΩ resistor)
at 85±3°C and 80 to 85% humidity for 1000±12h.
Humidity
Capacitance Within ±5% or ± 0.5pF
Change
Q
(Whichever is larger)
Q ≧ 200
Remove and let sit for 24±2 h at *room condition, then measure.
The charge/discharge current is less than 50mA.
I.R.
500MΩ min.
Operational
Life
Appearance
No defects or abnormalities except color
change of outer coating.
Apply 25% of the rated voltage for 1000±12h at 200±5°C.
Let sit for 24±2 h at *room condition, then measure.
The charge/discharge current is less than 50mA.
Capacitance Within ±3% or ±0.3pF
Change
Q
(Whichever is larger)
Q ≧ 350
I.R.
1,000MΩ min.
7
8
9
External Visual
No defects or abnormalities.
Within the specified dimensions.
To be easily legible.
No defects or abnormalities.
Visual inspection.
Physical Dimension
Marking
Using calipers and micrometers.
Visual inspection.
10 Resistance
to Solvents
Appearance
Per MIL-STD-202 Method 215
Capacitance Within the specified tolerance.
Solvent 1 : 1 part (by volume) of isopropyl alcohol
3 parts (by volume) of mineral spirits
Solvent 2 : Terpene defluxer
Q
Q ≧ 1,000
I.R.
10,000MΩ min.
Solvent 3 : 42 parts (by volume) of water
1 part (by volume) of propylene glycol monomethyl ether
1 part (by volume) of monoethanolamine
* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa
ESRH04
7/14
Reference only
AEC-Q200
Test Item
No.
Specification
AEC-Q200 Test Method
11 Mechanical
Shock
Appearance
No defects or abnormalities.
Three shocks in each direction should be applied along 3
mutually perpendicular axes of the test specimen (18 shocks).
The specified test pulse should be Half-sine and should have a
duration : 0.5ms, peak value : 1500G and velocity change : 4.7m/s.
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 2000Hz.
The frequency range, from 10 to 2000Hz and return to 10Hz,
should be traversed in approximately 20 min. This motion
should be applied for 12 items in each 3 mutually perpendicular
directions (total of 36 times).
Capacitance Within the specified tolerance.
Q
Q ≧ 1,000
12 Vibration
Appearance
No defects or abnormalities.
Capacitance Within the specified tolerance.
Q
Q ≧ 1,000
13-1 Resistance to Appearance
No defects or abnormalities.
The lead wires should be immersed in the melted solder 1.5 to 2.0mm
from the root of terminal at 260±5°C for 10±1 seconds.
Soldering
Heat
Capacitance Within ±2.5% or ±0.25pF
Change
(Whichever is larger)
No defects
(Non-
Dielectric
Strength
(Between
terminals)
• Post-treatment
Preheat)
Capacitor should be stored for 24±2 hours at *room condition.
13-2 Resistance to Appearance
No defects or abnormalities
First the capacitor should be stored at 120+0/-5°C for 60+0/-5 seconds.
Then, the lead wires should be immersed in the melted solder
Soldering
Heat
Capacitance Within ±2.5% or ±0.25pF
Change
(Whichever is larger)
No defects
1.5 to 2.0mm from the root of terminal at 260±5°C for 7.5+0/-1 seconds.
(On-
Dielectric
Strength
(Between
terminals)
Preheat)
• Post-treatment
Capacitor should be stored for 24±2 hours at *room condition.
13-3 Resistance to Appearance
No defects or abnormalities.
Test condition
Soldering
Heat
Capacitance Within ±2.5% or ±0.25pF
Temperature of iron-tip : 350±10°C
Soldering time : 3.5±0.5 seconds
Soldering position
Change
(Whichever is larger)
No defects
(soldering
Dielectric
iron method) Strength
(Between
Straight Lead : 1.5 to 2.0mm from the root of terminal.
Crimp Lead : 1.5 to 2.0mm from the end of lead bend.
terminals)
• Post-treatment
Capacitor should be stored for 24±2 hours at *room condition.
Perform the 300 cycles according to the two heat treatments listed
in the following table(Maximum transfer time is 20 seconds.).
Let sit for 24±2 h at *room condition, then measure.
14 Thermal
Shock
Appearance
No defects or abnormalities.
Capacitance Within ±5% or ±0.5pF
Change
Q
(Whichever is larger)
Q ≧ 350
Step
1
2
I.R.
1,000MΩ min.
Temp.
(°C)
-55+0/-3
200+5/-0
Time
(min.)
15±3
15±3
15 ESD
Appearance
No defects or abnormalities.
Per AEC-Q200-002
Capacitance Within the specified tolerance.
Q
Q ≧ 1,000
I.R.
10,000MΩ min.
16 Solderability
Lead wire should be soldered with
uniform coating on the axial direction over
95% of the circumferential direction.
The terminal of a capacitor is dipped into a solution of ethanol
(JIS-K-8101) and rosin (JIS-K-5902) (25%rosin in weight propotion)
and then into molten solder (JIS-Z-3282) for 2±0.5 seconds.
In both cases the depth of dipping is up to about 1.5 to 2mm from
the terminal body.
Temp. of solder :
245±5°C Lead Free Solder (Sn-3.0Ag-0.5Cu)
235±5°C H60A or H63A Eutectic Solder
* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa
ESRH04
8/14
Reference only
AEC-Q200
Test Item
No.
Specifications
AEC-Q200 Test Method
17 Electrical
Characte-
rization
Appearance
No defects or abnormalities.
Visual inspection.
Capacitance Within the specified tolerance.
The capacitance, Q should be measured at 25°C at the frequency
and voltage shown in the table.
Q
Q ≧ 1,000
Nominal Cap. Frequency
C ≦ 1000pF 1±0.1MHz AC0.5 to 5V(r.m.s.)
C > 1000pF 1±0.1kHz AC1±0.2V(r.m.s.)
Voltage
Insulation
Resistance
(I.R.)
Room
10,000MΩ min.
The insulation resistance should be measured at 25±3 °C with a
DC voltage not exceeding the rated voltage at normal temperature
and humidity and within 2 min. of charging.
Temperature
(Charge/Discharge current ≦ 50mA.)
High
20MΩ min.
The insulation resistance should be measured at 200±5 °C with a
DC voltage not exceeding 25% of the rated voltage at normal
temperature and humidity and within 2 min. of charging.
(Charge/Discharge current ≦ 50mA.)
Temperature
Dielectric
Strength
Between
No defects or abnormalities.
The capacitor should not be damaged when voltage in Table is
applied between the terminations for 1 to 5 seconds.
(Charge/Discharge current ≦ 50mA.)
Terminals
Rated Voltage
DC200V
Test Voltage
250% of the rated voltage
150% of the rated voltage
DC500V
Body
No defects or abnormalities.
The capacitor is placed in a container with
metal balls of 1mm diameter so that each
terminal, short-circuit, is kept approximately
2mm from the balls as shown in the figure,
and voltage in table is impressed for 1 to 5
seconds between capacitor terminals and
metal balls.
Insulation
Approx.
2mm
Metal
balls
(Charge/Discharge current ≦ 50mA.)
Rated Voltage
DC200V
Test Voltage
250% of the rated voltage
150% of the rated voltage
DC500V
18 Terminal
Strength
Tensile
Termination not to be broken or loosened.
As in the figure, fix the capacitor body, apply the force gradually
to each lead in the radial direction of the capacitor until reaching
10N and then keep the force applied for 10±1 seconds.
Strength
F
↓
Bending
Strength
Termination not to be broken or loosened.
Each lead wire should be subjected to a force of 2.5N and then
be bent 90° at the point of egress in one direction. Each wire is
then returned to the original position and bent 90° in the opposite
direction at the rate of one bend per 2 to 3 seconds.
The capacitance change should be measured after 5min. at
each specified temperature step.
19 Capacitance
Temperature
Within the specified Tolerance.
-750+120/-347ppm/°C (-55 to 25°C)
Characteristics
-750±120ppm/°C
(25 to 125°C)
Step
Temperature(°C)
25±2
-750+347/-120ppm/°C (125 to 200°C)
1
2
3
4
5
-55±3
25±2
200±5
25±2
The temperature coefficient is determined using the capacitance
measured in step 3 as a reference. When cycling the temperature
sequentially from step 1 through 5 (-55°C to 150°C)
the capacitance should be within the specified tolerance for the
temperature coefficient and capacitance change as Table A.
The capacitance drift is calculated by dividing the differences
between the maximum and minimum measured values in the
step 1, 3 and 5 by the capacitance value in step 3.
* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa
ESRH04
9/14
Reference only
6. Packing specification
・Bulk type (Packing style code : B)
The size of packing case and packing way
Polyethylene bag
Partition
270 max.
125 max.
Unit : mm
340 max.
The number of packing = *1 Packing quantity × *2 n
*1 : Please refer to [Part number list].
*2 : Standard n = 20 (bag)
Note)
The outer package and the number of outer packing be changed by the order getting amount.
JKBCRPE02
10/14
Reference only
・Ammo pack taping type (Packing style code : A)
ꢀꢀꢀꢀꢀꢀA crease is made every 25 pitches, and the tape with capacitors is packed zigzag into a case.
ꢀꢀꢀꢀꢀꢀWhen body of the capacitor is piled on other body under it.
The size of packing case and packing way
240 max.
Position of label
340 max.
Unit : mm
51 max.
Hold down tape
Capacitor
Base tape
Hold down
tape upper
EKTRPE01
11/14
Reference only
7. Taping specification
7-1. Dimension of capacitors on tape
Straight taping type < Lead Style : DG >
Pitch of component 12.7mm / Lead spacing 2.5mm
P
P2
0
△S
△h2
△h1
Marking
e
P1
Φd
F
ΦD0
P0
Unit : mm
Item
Code
Dimensions
12.7+/-1.0
12.7+/-0.2
2.5+0.4/-0.2
Remarks
Pitch of component
P
P0
F
Pitch of sprocket hole
Lead spacing
Length from hole center to component
center
P2
6.35+/-1.3
Deviation of progress direction
They include deviation by lead bend
Deviation of tape width direction
Length from hole center to lead
P1
ΔS
W
5.1+/-0.7
0+/-2.0
Deviation along tape, left or right defect
Carrier tape width
18.0+/-0.5
9.0+0/-0.5
Position of sprocket hole
W1
Lead distance between reference and
bottom plane
H
20.0+/-0.5
Protrusion length
0.5 max.
4.0+/-0.1
0.5+/-0.05
0.6+/-0.3
1.5 max.
Diameter of sprocket hole
Lead diameter
ΦD0
Φd
t1
Total tape thickness
They include hold down tape
thickness
Total thickness of tape and lead wire
t2
Δh1
Δh2
L
Deviation across tape
1.0 max.
Portion to cut in case of defect
Hold down tape width
11.0+0/-1.0
9.5 min.
W0
W2
e
Hold down tape position
Coating extension on lead
1.5+/-1.5
2.0 max.
ETP1DBG01A
12/14
Reference only
Inside crimp taping type < Lead Style : M2 >
Pitch of component 12.7mm / Lead spacing 5.0mm
Unit : mm
Item
Code
P
Dimensions
12.7+/-1.0
12.7+/-0.2
5.0+0.6/-0.2
Remarks
Pitch of component
Pitch of sprocket hole
Lead spacing
P0
F
Length from hole center to component
center
P2
6.35+/-1.3
Deviation of progress direction
They include deviation by lead bend
Deviation of tape width direction
Length from hole center to lead
Deviation along tape, left or right defect
Carrier tape width
P1
ΔS
W
3.85+/-0.7
0+/-2.0
18.0+/-0.5
9.0+0/-0.5
Position of sprocket hole
W1
Lead distance between reference and
bottom plane
H0
20.0+/-0.5
Protrusion length
0.5 max.
4.0+/-0.1
0.5+/-0.05
0.6+/-0.3
1.5 max.
Diameter of sprocket hole
Lead diameter
ΦD0
Φd
t1
Total tape thickness
They include hold down tape
thickness
Total thickness of tape and lead wire
t2
2.0 max. (Dimension code : W)
1.0 max. (except as above)
11.0+0/-1.0
Δh1
Δh2
L
Deviation across tape
Portion to cut in case of defect
Hold down tape width
W0
W2
e
9.5 min.
Hold down tape position
Coating extension on lead
1.5+/-1.5
Up to the end of crimp
ETP1M201A
13/14
Reference only
7-2. Splicing way of tape
1) Adhesive force of tape is over 3N at test condition as below.
W
Hold down tape
Base tape
2) Splicing of tape
a) When base tape is spliced
•Base tape shall be spliced by cellophane tape.
(Total tape thickness shall be less than 1.05mm.)
Progress direction
in production line
Hold down tape
Base tape
About 30 to 50
No lifting for the
Cellophane tape
direction of
progressing
Unit : mm
b) When hold down tape is spliced
•Hold down tape shall be spliced with overlapping.
(Total tape thickness shall be less than 1.05mm.)
20 to 30
Hold down tape
Base tape
Unit : mm
Progress direction
in production line
c) When both tape are spliced
•Base tape and hold down tape shall be spliced with splicing tape.
ETP2R01
14/14
相关型号:
©2020 ICPDF网 联系我们和版权申明