NFM18CC [MURATA]
CHIP EMIFIL®CHIP 3-TERMINAL CAPACITOR FOR LARGE CURRENT FOR GENERALnull;
| 型号： | NFM18CC |
| 厂家： | 
muRata |
| 描述： | CHIP EMIFIL®CHIP 3-TERMINAL CAPACITOR FOR LARGE CURRENT FOR GENERALnull |
| 文件： | 总11页 (文件大小：713K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
No.JEMCP0-010859B
CHIP EMIFIL®CHIP 3-TERMINAL CAPACITOR FOR LARGE CURRENT FOR GENERAL
NFM18CC Series Reference Sheet
1.Scope
This product specification is applied to Chip EMIFIL®Chip 3-terminal Capacitor used for General Electronic equipment.
2.Reference PART No. List
Customer PART NO.
MURATA PART NO.
NFM18CC101R1C3D
1
2
3
4
5
6
7
8
NFM18CC102R1C3D
NFM18CC220U1C3D
NFM18CC221R1C3D
NFM18CC222R1C3D
NFM18CC223R1C3D
NFM18CC470U1C3D
NFM18CC471R1C3D
3.MURATA Part NO. System
(Ex.)
NFM
18
CC
101
R
1C
3
D
(7)Packaging
Code
(3)Nominal
Capacitance
(4)
(5)DC Rated
Voltage
(1)L/W
Dimensions
(6)Electrode
(2)Features
Characteristics
4. Type & Dimensions
(Unit:mm)
(1)-1 L
(1)-2 W
T
e
g
MURATA PART NO.
1 NFM18CC101R1C3D
2 NFM18CC102R1C3D
3 NFM18CC220U1C3D
4 NFM18CC221R1C3D
5 NFM18CC222R1C3D
6 NFM18CC223R1C3D
7 NFM18CC470U1C3D
8 NFM18CC471R1C3D
i
j
1.6±0.1
0.4±0.1
1.6±0.1
0.4±0.1
1.6±0.1
0.4±0.1
1.6±0.1
0.4±0.1
1.6±0.1
0.4±0.1
1.6±0.1
0.4±0.1
1.6±0.1
0.4±0.1
1.6±0.1
0.4±0.1
0.8±0.1
0.2±0.1
0.8±0.1
0.2±0.1
0.8±0.1
0.2±0.1
0.8±0.1
0.2±0.1
0.8±0.1
0.2±0.1
0.8±0.1
0.2±0.1
0.8±0.1
0.2±0.1
0.8±0.1
0.2±0.1
0.6±0.1
0.25±0.1
0.2 min.
0.6±0.1
0.6±0.1
0.6±0.1
0.6±0.1
0.6±0.1
0.6±0.1
0.6±0.1
0.25±0.1
0.25±0.1
0.25±0.1
0.25±0.1
0.25±0.1
0.25±0.1
0.25±0.1
0.2 min.
0.2 min.
0.2 min.
0.2 min.
0.2 min.
0.2 min.
0.2 min.
1
No.JEMCP0-010859B
a)Equivalent Circuit
5.Rated value
(5)
Rated
Voltage
Rated
Current
(mA)
(3) Nominal Capacitance
Capacitance Tolerance
DC
Insulation
Specifications and Test Methods
(Operating / Storage Temp. Range)
MURATA PART NO.
Resistance Resistance
Section 7.1
(-55 to 125 °C / -55 to 125 °C)
Section 7.1
(-55 to 125 °C / -55 to 125 °C)
Section 7.1
(-55 to 125 °C / -55 to 125 °C)
Section 7.1
(-55 to 125 °C / -55 to 125 °C)
Section 7.1
(-55 to 125 °C / -55 to 125 °C)
Section 7.1
(-55 to 125 °C / -55 to 125 °C)
Section 7.1
(-55 to 125 °C / -55 to 125 °C)
Section 7.1
(-55 to 125 °C / -55 to 125 °C)
NFM18CC101R1C3D
NFM18CC102R1C3D
NFM18CC220U1C3D
NFM18CC221R1C3D
NFM18CC222R1C3D
NFM18CC223R1C3D
NFM18CC470U1C3D
NFM18CC471R1C3D
100 pF
1000 pF
22 pF
±20 %
±20 %
±20 %
±20 %
±20 %
±20 %
±20 %
±20 %
DC 16 V 500mA(DC) 0.3Ωmax. 1000MΩmin.
DC 16 V 600mA(DC) 0.3Ωmax. 1000MΩmin.
DC 16 V 400mA(DC) 0.3Ωmax. 1000MΩmin.
DC 16 V 500mA(DC) 0.3Ωmax. 1000MΩmin.
DC 16 V 700mA(DC) 0.3Ωmax. 1000MΩmin.
1
2
3
4
5
6
7
8
220 pF
2200 pF
22000 pF
47 pF
DC 16 V
1A(DC) 0.05Ωmax. 1000MΩmin.
DC 16 V 400mA(DC) 0.3Ωmax. 1000MΩmin.
470 pF
DC 16 V 500mA(DC) 0.3Ωmax. 1000MΩmin.
6.Package
MURATA PART NO.
(7) Packaging
Packaging Unit
4000 pcs./Reel
f180mm Reel
PAPER
f180mm Reel
PAPER
f180mm Reel
PAPER
f180mm Reel
PAPER
f180mm Reel
PAPER
f180mm Reel
PAPER
f180mm Reel
PAPER
f180mm Reel
PAPER
NFM18CC101R1C3D
NFM18CC102R1C3D
NFM18CC220U1C3D
NFM18CC221R1C3D
NFM18CC222R1C3D
NFM18CC223R1C3D
NFM18CC470U1C3D
NFM18CC471R1C3D
1
2
3
4
5
6
7
8
4000 pcs./Reel
4000 pcs./Reel
4000 pcs./Reel
4000 pcs./Reel
4000 pcs./Reel
4000 pcs./Reel
4000 pcs./Reel
Product specifications in this catalog are as of Dec.15,2014,and are subject to change or obsolescence without notice.
Please consult the approval sheet before ordering.
Please read rating and !Cautions first.
2
7.1
7
■SPECIFICATIONS AND TEST METHODS
Electrical Performance
No
1
Item
Capacitance
Specification
Test Method
Frequency
Meet item 5.
22 to 47pF : 1±0.1MHz
100 to 22000pF : 1±0.1kHz
Voltage : 1±0.2V(rms)
(Cap.)
Voltage : Rated Voltage
Time : 2 minutes max.
2
3
Insulation
Resistance(I.R.)
DC Resistance
(Rdc1,2)
Measured with 100mA max.
Rdc1 : between signal terminals
Rdc2 : between ground terminals
Rdc2
Rdc1
Rdc1
Rdc2
4
Withstanding Voltage
Products shall not be damaged.
Shown in item 5.
Test Voltage : Rated Voltage x 300%
Time : 1 to 5 s
Charge Current : 50 mA max.
Operating Temperature
Storage Temperature
5
6
Includes self-heating
Standard Testing Condition
< Unless otherwise specified >
Temperature : Ordinary Temp. / 15 °C to 35 °C
< In case of doubt >
Temperature: 20 °C ± 2 °C
Humidity: Ordinary Humidity / 25 %(RH) to 85 %(RH) Humidity: 60 %(RH) to 70 %(RH)
Atmospheric pressure: 86 kPa to 106 kPa
3
JEMCPS-02209B
7.1
7
■SPECIFICATIONS AND TEST METHODS
Mechanical Performance
No
1
Item
Appearance and
Dimensions
Specification
Test Method
Visual Inspection and measured with Slide Calipers or
Micrometer.
Meet item 4.
2
3
Solderability
Electrodes shall be at least 90% covered with
new solder coating.
Flux : Ethanol solution of rosin, 25(wt)%
Pre-heat : 150±10°C, 60 to 90s
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 240 ± 3°C
Immersion Time : 3±1 s
Immersion and emersion rates : 25mm / s
Resistance to
soldering heat
Meet Table 1.
Table 1
Flux : Ethanol solution of rosin, 25(wt)%
Pre-heat : 150±10°C, 60 to 90s
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 270 ± 5°C
Immersion Time : 10 ± 1 s
Immersion and emersion rates : 25mm / s
Initial values : About 100 to 22000pF,
measured after heat treatment (150+0 / -10 °C,1hour) and
exposure in the room condition for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
Appearance
Cap. Change
I.R.
No damaged
Within ±7.5%
Meet the initial rated value.
22 to 2200pF
22000pF
0.5 max.
0.05 max.
Rdc 1,2
22 to 47pF : 24±2 hours
100 to 22000pF : 48±4 hours
4
Bending Strength
Meet Table 2.
Table 2
It shall be soldered on the glass-epoxy substrate(t = 1.0mm).
Deflection : 2 mm
Keeping Time : 30 s
Pressure jig
Appearance
Cap. Change
No damaged
Within ±7.5%
22 to 2200pF
22000pF
R340
F
0.5 max.
0.05 max.
Rdc 1,2
Deflection
Product
45
45
(in mm)
5
6
Drop
Products shall be no failure after tested.
It shall be dropped on concrete or steel board.
Method : Free fall
Height : 1 m
Attitude from which the product is dropped : 3 directions
The Number of Time : 3 times for each direction
(Total 9 times)
Bonding Strength
The electrodes shall be no failure after tested.
It shall be soldered on the glass-epoxy substrate.
Applying Force (F) : 9.8 N
Applying Time : 30 s
0.5
0.6
(in mm)
0.4
1.6
7
Vibration
Meet Table 3.
Table 3
Appearance
Capacitance
It shall be soldered on the glass-epoxy substrate.
Oscillation Frequency : 10 to 2000 to 10Hz for 20 minutes.
Total amplitude 1.5 mm or Acceleration amplitude 196m/s2
whichever is smaller.
No damaged
Meet the initial rated value.
22 to 2200pF
22000pF
0.5 max.
0.05 max.
Time : A period of 2 hours in each of 3 mutually
perpendicular directions. (Total 6 hours)
Initial values : About 100 to 22000pF,
Rdc 1,2
measured after heat treatment (150+0 / -10 °C,1hour)
and exposure in the room condition for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
22 to 47pF
: 24±2 hours
100 to 22000pF : 48±4 hours
4
JEMCPS-02209B
7.1
7
■SPECIFICATIONS AND TEST METHODS
Environment Performance
It shall be soldered on the glass-epoxy substrate.
No
1
Item
Specification
Test Method
1 Cycle
Temperature Cycling Meet Table 1.
1 step : -55+0 / -3℃ / 30+3 / -0 min
2 step : Room Temperature / within 3 min
3 step : +125+3 / -0℃ / 30+3 / -0 min
4 step : Room Temperature / within 3 min
Total of 10 cycles
Initial values : About 100 to 22000pF, measured after heat
treatment(150+0 / -10°C,1hour) and exposure in the room
condition for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
22 to 47pF
: 24±2 hours
100 to 22000pF : 48±4 hours
About 100 to 22000pF, If it’s doubt, measured after heat
treatment (150+0 / -10 °C,1hour) and exposure in the room
condition for 48±4 hours.
2
Humidity
Meet Table 4.
Table 4
Temperature : 40±2°C
Humidity : 90 to 95%(RH)
Time : 500+24 / -0 hours
Appearance
Cap. Change
I.R.
No damaged
Within ±12.5%
Meet the initial rated value.
22 to 2200pF
22000pF
Initial values : About 100 to 22000pF,measured after heat
treatment (150+0 / -10 °C,1hour), and exposure in the room
condition for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
0.5 max.
0.05 max.
Rdc 1,2
22 to 47pF
: 24±2 hours
100 to 22000pF : 48±4 hours
About 100~22000pF, If it’s doubt, measured after heat
treatment (150+0 / -10 °C,1hour) and exposure in the room
condition for 48±4 hours.
3
Heat Life
Temperature : 125±2°C
Test Voltage : Rated Voltage x 200%
Charge Current : 50 mA max.
Time : 1000+48 / -0 hours
Initial values : About 100 to 22000pF,measured after voltage
treatment (Maximum Operating Temperature±2°C, Rated
Voltage x 200%, 1hour) and exposure in the room condition
for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
22 to 47pF
: 24±2 hours
100 to 22000pF : 48±4 hours
4
Cold Resistance
Temperature : -55±2°C
Time : 500+24 / -0 hours
Initial values : About 100 to 22000pF,measured after heat
treatment (150+0 / -10 °C,1hour), and exposure in the room
condition for 48±4 hours.
Then measured after exposure in the room condition for
following hours.
22 to 47pF : 24±2 hours
100 to 22000pF : 48±4 hours
About 100 to 22000pF, If it’s doubt, measured after heat
treatment (150+0 / -10 °C,1hour) and exposure in the room
condition for 48±4 hours.
5
JEMCPS-02209B
8
P A C K A G I N G
NFM18 Type
1. Appearance and Dimensions (8mm-wide paper tape)
4.0±0.1
1.5±00.1
Sporocket Hole
Chip thickness
Dimension
(a)
1.1max
0.9max
(T)
0.8
0.6
(in mm)
1.05±0.1
4.0±0.1 2.0±0.05
0.9max.
a
2. Specification of Taping
Direction of feed
(1) Packing quantity (standard quantity)
4000 pcs. / reel
(2) Packing Method
Products shall be packaged in the cavity of the base tape and sealed by top tape and bottom tape.
(3) Sprocket Hole
The sprocket holes are to the right as the tape is pulled toward the user.
(4) Base tape and Top tape
The base tape and top tape have no spliced point.
(5) Cavity
There shall not be burr in the cavity.
(6) Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater,and are not continuous.
The specified quantity per reel is kept.
3. Pull Strength of Top Tape
5Nmin.(※Only for NFM18PS, 8Nmin.)
4. Peeling off force of top tape
Top tape
165 to 180 degree
Bottom tape
0.1N to 0.6N (minimum value is typical)
Speed of Peeling off : 300 mm / min
F
Base tape
5. Dimensions of Leader-tape, Trailer and Reel
There shall be leader-tape (top tape and empty tape) and trailer-tape (empty tape) as follows.
Trailer
Leader
160 min.
2.0±0.5
190 min.
Empty tape
210 min.
Top tape
Label
13.0±0.2
60±1
0
21.0±0.8
Direction of feed
9± 10
13±1.4
(in mm)
180±0
3
JEMCPP-02231A
6
9
Caution
!
1. Mounting density
Add special attention to radiating heat of products when mounting this product near the products with heating.
The excessive heat by other products may cause deterioration of insulation resistance and excessive heat at this product,
resulting in a fire.
2. Limitation of Applications
Please contact us before using our products for the applications listed below which require especially high
reliability for the prevention of defects which might directly cause damage to the third party's life, body or property.
(1)Aircraft equipment (2)Aerospace equipment (3)Undersea equipment (4)Power plant control equipment
(5)Medical equipment (6)Transportation equipment(automobiles, trains, ships, etc.) (7)Traffic signal equipment
(8)Disaster prevention / crime prevention equipment (9)Data-processing equipment
(10)Applications of similar complexity or with reliability requirements comparable to the applications listed in the above
JEMCPC-02244A
7
9
Notice
Products can only be soldered with reflow.
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
1. Flux and Solder
Flux
Use rosin-based flux, Do not use highly acidic flux (with chlorine content exceeding 0.2(wt)%).
Do not use water-soluble flux.
Other flux (except above) Please contact us for details, then use.
Use Sn-3.0Ag-0.5Cu solder
Solder
Use of Sn-Zn based solder will deteriorate performance of products.
In case of using Sn-Zn based solder, please contact Murata in advance.
2. Note for Assembling
< Thermal Shock >
Pre-heating should be in such a way that the temperature difference between solder and products surface is limited
to 100°C max. Also cooling into solvent after soldering should be in such a way that the temperature difference is
limited to 100°C max.
3. Attention Regarding P.C.B. Bending
The following shall be considered when designing P.C.B.'s and laying out products.
(1) P.C.B. shall be designed so that products are not subject to the mechanical stress for board warpage.
[Products direction]
a
b
Products shall be located in the sideways
direction (Length:a<b) to the mechanical stress.
Poor example
〈
〉
Good example
〈
〉
(2) Products location on P.C.B. near seam for separation.
C
B
Seam
Products (A,B,C,D) shall be located carefully so that products are
not subject to the mechanical stress due to warping the board.
Because they may be subjected the mechanical stress in order
of A>C>B≒D.
D
A
a
b
Slit
Length:a b
4.Pre-heating Temperature
Soldering shall be handled so that the difference between pre-heating temperature and solder temperature shall be
limited to 100°C max. to avoid the heat stress for the products.
5.Reflow Soldering
• Standard printing pattern of solder paste.
1) Soldering paste printing for reflow
• Standard thickness of solder paste: 100µm to 150µm.
• Use the solder paste printing pattern of the right pattern.
• For the resist and copper foil pattern, use standard land dimensions.
0.4
1.0
(in mm)
2.2
2) Soldering Conditions
Standard soldering profile and the limit soldering profile is as follows.
The excessive limit soldering conditions may cause leaching of the electrode and / or resulting in the deterioration of
product quality.
(°C)
Temp.
260°C
245°C±3°C
230°C
220°C
Limit Profile
180
150
30s 60s
～
Standard Profile
60s max.
90s±30s
Time.(s)
Standard Profile
Limit Profile
Pre-heating
150°C ~ 180°C , 90s ± 30s
above 220°C , 30s ~ 60s
245°C ± 3°C
Heating
above 230°C , 60s max.
260°C , 10s
Peak temperature
Cycle of reflow
2 times
2 times
JEMCPC-02244A
8
9
Notice
6. Reworking with Soldering iron
The following conditions shall be strictly followed when using a soldering iron.
Pre-heating : 150°C, 1 min
Tip temperature : 350°C max.
Soldering time : 3(+1,-0) s
•Soldering iron output : 30W max.
• Tip diameter : φ3mm max.
• Times : 2times max.
Note: Do not directly touch the products with the tip of the soldering iron in order to prevent the crack on the
ceramic material due to the thermal shock.
7. Solder Volume
Solder shall be used not to be exceeded as shown below.
Upper Limit
Upper Limit
Recommendable
Recommendable
t
1/3T t T(T:Chip thickness)
Accordingly increasing the solder volume, the mechanical stress to product is also increased.
Excessive solder volume may cause the failure of mechanical or electrical performance.
8. Cleaning Conditions
Products shall be cleaned on the following conditions.
(1) Cleaning temperature shall be limited to 60°C max. (40°C max. for Isopropyl alcohol (IPA))
(2) Ultrasonic cleaning shall comply with the following conditions, with avoiding the resonance phenomenon at the
mounted products and P.C.B.
Power
: 20W / l max.
Frequency : 28kHz to 40kHz
Time
: 5 minutes max.
(3) Cleaner
1. Cleaner
Isopropyl alcohol (IPA)
PINE ALPHA ST-100S
(4) There shall be no residual flux and residual cleaner after cleaning.
In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized water in order to
remove the cleaner.
(5) Other cleaning
Please contact us.
9. Operating Environment
Do not use this product under the following environmental conditions, on deterioration of the performance, such as
insulation resistance may result from the use.
(1) in the corrodible atmosphere (acidic gases, alkaline gases, chlorine, sulfur gases, organic gases and etc.)
(2) in the atmosphere where liquid such as organic solvent, may splash on the products.
(3) in the atmosphere where the temperature / humidity changes rapidly and it is easy to dew.
10. Resin coating
The capacitance value may change and/or it may affect on the product's performance due to high cure-stress of resin
to be used for coating / molding products. So please pay your careful attention when you select resin. In prior to use, please
make the reliability evaluation with the product mounted in your application set.
11. Handling of a substrate
After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate
when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate.
Excessive mechanical stress may cause cracking in the product.
Bending
Twisting
JEMCPC-02244A
9
9
Notice
12. Standard Land Dimensions
The chip EMI filter suppresses noise by conducting the high-frequency noise element to ground.
Therefore, to get enough noise reduction, feed through holes which is connected to ground-plane should be
arranged according to the figure to reinforce the ground-pattern.
< Standard land dimensions for reflow >
･Side on which chips are mounted
Small diameter thru hole 0.2 0.3
～
0.4
0.6
1.0
2.2
Resist
Copper foil pattern
No pattern
(in mm)
13. Storage condition
(1) Storage period
Use the products within 12 months after delivered.
Solderability should be checked if this period is exceeded.
(2) Storage environment condition
・Products should be stored in the warehouse on the following conditions.
Temperature: -10 to +40°C
Humidity: 15 to 85% relative humidity
No rapid change on temperature and humidity
・Don't keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization of electrode,
resulting in poor solderability.
・Products should be stored on the palette for the prevention of the influence from humidity, dust and so on.
・Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.
・Products should be stored under the airtight packaged condition.
(3) Delivery
Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock.
JEMCPC-02244A
10
9
NOTE
!
(1) Please make sure that your product has been evaluated in view of your specifications with our product being mounted
to your product.
(2) You are requested not to use our product deviating from the agreed specifications.
(3) We consider it not appropriate to include any terms and conditions with regard to the business transaction in the
product specifications, drawings or other technical documents. Therefore, if your technical documents as above
include such terms and conditions such as warranty clause, product liability clause, or intellectual property infringement
liability clause, they will be deemed to be invalid.
JEMCPC-02244A
11
相关型号：
NFM18CC220U1C3B
Feed Through Capacitor, 1 Function(s), 16V, 0.4A, EIA STD PACKAGE SIZE 0603, 3 PIN
MURATA
NFM18CC221R1C3B
Feed Through Capacitor, 1 Function(s), 16V, 0.5A, EIA STD PACKAGE SIZE 0603, 3 PIN
MURATA
©2020 ICPDF网 联系我们和版权申明