LQP02TQ3N5C02# [MURATA]
;型号: | LQP02TQ3N5C02# |
厂家: | muRata |
描述: | |
文件: | 总16页 (文件大小:751K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Spec No.: JELF243C_0019K-01
P1/16
CHIP COILS (CHIP INDUCTORS) LQP02TQ□□□□02□ REFERENCE SPECIFICATION
1. Scope
This reference specification applies to chip coils (chip inductors) LQP02TQ_02 series for general electronic equipment.
2. Part Numbering
(Ex.)
LQ
P
02
T
Q
0N2
B
0
2
D
Product Structure Dimension Application Category Inductance Tolerance Performance Electrode
Packaging
ID
(L × W)
and
characteristic
specification L: 4 mm width
/plastic tape
D: 8 mm width
/paper tape
*B: bulk
*B: Bulk packing is also available (taping condition: however, products without reels are put in plastic bags).
3. Part Number and Rating
Operating temperature range
Storage temperature range
-55°C to +125°C
-55°C to +125°C
Self-resonant
frequency
(GHz)
Inductance
DC
resistance
(Ω max.)
Rated
current
(mA)
Customer
Part number
Murata
Part number
Q
(Min.)
Nominal
value
*Typical
value
Lower
limit
Tolerance
(nH)
LQP02TQ0N2B02D
LQP02TQ0N2B02L
LQP02TQ0N2C02D
LQP02TQ0N2C02L
LQP02TQ0N3B02D
LQP02TQ0N3B02L
LQP02TQ0N3C02D
LQP02TQ0N3C02L
LQP02TQ0N4B02D
LQP02TQ0N4B02L
LQP02TQ0N4C02D
LQP02TQ0N4C02L
LQP02TQ0N5B02D
LQP02TQ0N5B02L
LQP02TQ0N5C02D
LQP02TQ0N5C02L
LQP02TQ0N6B02D
LQP02TQ0N6B02L
LQP02TQ0N6C02D
LQP02TQ0N6C02L
LQP02TQ0N7B02D
LQP02TQ0N7B02L
LQP02TQ0N7C02D
LQP02TQ0N7C02L
LQP02TQ0N8B02D
LQP02TQ0N8B02L
LQP02TQ0N8C02D
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.8
0.8
0.8
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
-
0.1
0.1
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
990
990
990
990
990
990
990
990
990
990
990
990
730
730
730
730
730
730
730
730
630
630
630
630
630
630
630
-
-
0.1
-
0.1
-
0.1
-
0.1
-
0.1
-
0.1
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.15
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
Customer
P2/16
Self-resonant
frequency
(GHz)
Inductance
Nominal
DC
resistance
(Ω max.)
Rated
current
(mA)
Murata
Q
(Min.)
Part number
Part number
*Typical
value
Lower
limit
value
(nH)
Tolerance
LQP02TQ0N8C02L
LQP02TQ0N9B02D
LQP02TQ0N9B02L
LQP02TQ0N9C02D
LQP02TQ0N9C02L
LQP02TQ1N0B02D
LQP02TQ1N0B02L
LQP02TQ1N0C02D
LQP02TQ1N0C02L
LQP02TQ1N1B02D
LQP02TQ1N1B02L
LQP02TQ1N1C02D
LQP02TQ1N1C02L
LQP02TQ1N2B02D
LQP02TQ1N2B02L
LQP02TQ1N2C02D
LQP02TQ1N2C02L
LQP02TQ1N3B02D
LQP02TQ1N3B02L
LQP02TQ1N3C02D
LQP02TQ1N3C02L
LQP02TQ1N4B02D
LQP02TQ1N4B02L
LQP02TQ1N4C02D
LQP02TQ1N4C02L
LQP02TQ1N5B02D
LQP02TQ1N5B02L
LQP02TQ1N5C02D
LQP02TQ1N5C02L
LQP02TQ1N6B02D
LQP02TQ1N6B02L
LQP02TQ1N6C02D
LQP02TQ1N6C02L
LQP02TQ1N7B02D
LQP02TQ1N7B02L
LQP02TQ1N7C02D
LQP02TQ1N7C02L
LQP02TQ1N8B02D
LQP02TQ1N8B02L
LQP02TQ1N8C02D
LQP02TQ1N8C02L
LQP02TQ1N9B02D
LQP02TQ1N9B02L
LQP02TQ1N9C02D
0.8
0.9
0.9
0.9
0.9
1.0
1.0
1.0
1.0
1.1
1.1
1.1
1.1
1.2
1.2
1.2
1.2
1.3
1.3
1.3
1.3
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.7
1.7
1.7
1.7
1.8
1.8
1.8
1.8
1.9
1.9
1.9
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
>20
19.6
19.6
19.6
19.6
>20
>20
>20
>20
19
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
16.6
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
13.0
13.0
13.0
630
580
580
580
580
580
580
580
580
570
570
570
570
550
550
550
550
400
400
400
400
400
400
400
400
400
400
400
400
390
390
390
390
380
380
380
380
380
380
380
380
380
380
380
19
19
19
>20
>20
>20
>20
18.9
18.9
18.9
18.9
19.0
19.0
19.0
19.0
17.7
17.7
17.7
17.7
16.8
16.8
16.8
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
Customer
P3/16
Self-resonant
frequency
(GHz)
Inductance
Nominal
DC
resistance
(Ω max.)
Rated
current
(mA)
Murata
Q
(Min.)
Part number
Part number
*Typical
value
Lower
limit
value
(nH)
Tolerance
LQP02TQ1N9C02L
LQP02TQ2N0B02D
LQP02TQ2N0B02L
LQP02TQ2N0C02D
LQP02TQ2N0C02L
LQP02TQ2N1B02D
LQP02TQ2N1B02L
LQP02TQ2N1C02D
LQP02TQ2N1C02L
LQP02TQ2N2B02D
LQP02TQ2N2B02L
LQP02TQ2N2C02D
LQP02TQ2N2C02L
LQP02TQ2N3B02D
LQP02TQ2N3B02L
LQP02TQ2N3C02D
LQP02TQ2N3C02L
LQP02TQ2N4B02D
LQP02TQ2N4B02L
LQP02TQ2N4C02D
LQP02TQ2N4C02L
LQP02TQ2N5B02D
LQP02TQ2N5B02L
LQP02TQ2N5C02D
LQP02TQ2N5C02L
LQP02TQ2N6B02D
LQP02TQ2N6B02L
LQP02TQ2N6C02D
LQP02TQ2N6C02L
LQP02TQ2N7B02D
LQP02TQ2N7B02L
LQP02TQ2N7C02D
LQP02TQ2N7C02L
LQP02TQ2N8B02D
LQP02TQ2N8B02L
LQP02TQ2N8C02D
LQP02TQ2N8C02L
LQP02TQ2N9B02D
LQP02TQ2N9B02L
LQP02TQ2N9C02D
LQP02TQ2N9C02L
LQP02TQ3N0B02D
LQP02TQ3N0B02L
LQP02TQ3N0C02D
1.9
2.0
2.0
2.0
2.0
2.1
2.1
2.1
2.1
2.2
2.2
2.2
2.2
2.3
2.3
2.3
2.3
2.4
2.4
2.4
2.4
2.5
2.5
2.5
2.5
2.6
2.6
2.6
2.6
2.7
2.7
2.7
2.7
2.8
2.8
2.8
2.8
2.9
2.9
2.9
2.9
3.0
3.0
3.0
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
0.3
0.3
16.8
15.4
15.4
15.4
15.4
14.6
14.6
14.6
14.6
16.3
16.3
16.3
16.3
16.2
16.2
16.2
16.2
16.2
16.2
16.2
16.2
14.9
14.9
14.9
14.9
14.6
14.6
14.6
14.6
13.5
13.5
13.5
13.5
12.8
12.8
12.8
12.8
12.3
12.3
12.3
12.3
12.2
12.2
12.2
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
380
380
380
380
380
380
380
380
380
380
380
380
380
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
360
360
360
360
360
360
360
360
360
360
360
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
Customer
P4/16
Self-resonant
frequency
(GHz)
Inductance
Nominal
DC
resistance
(Ω max.)
Rated
current
(mA)
Murata
Q
(Min.)
Part number
Part number
*Typical
value
Lower
limit
value
(nH)
Tolerance
LQP02TQ3N0C02L
LQP02TQ3N1B02D
LQP02TQ3N1B02L
LQP02TQ3N1C02D
LQP02TQ3N1C02L
LQP02TQ3N2B02D
LQP02TQ3N2B02L
LQP02TQ3N2C02D
LQP02TQ3N2C02L
LQP02TQ3N3B02D
LQP02TQ3N3B02L
LQP02TQ3N3C02D
LQP02TQ3N3C02L
LQP02TQ3N4B02D
LQP02TQ3N4B02L
LQP02TQ3N4C02D
LQP02TQ3N4C02L
LQP02TQ3N5B02D
LQP02TQ3N5B02L
LQP02TQ3N5C02D
LQP02TQ3N5C02L
LQP02TQ3N6B02D
LQP02TQ3N6B02L
LQP02TQ3N6C02D
LQP02TQ3N6C02L
LQP02TQ3N7B02D
LQP02TQ3N7B02L
LQP02TQ3N7C02D
LQP02TQ3N7C02L
LQP02TQ3N8B02D
LQP02TQ3N8B02L
LQP02TQ3N8C02D
LQP02TQ3N8C02L
LQP02TQ3N9B02D
LQP02TQ3N9B02L
LQP02TQ3N9C02D
LQP02TQ3N9C02L
LQP02TQ4N0B02D
LQP02TQ4N0B02L
LQP02TQ4N0C02D
LQP02TQ4N0C02L
LQP02TQ4N1B02D
LQP02TQ4N1B02L
LQP02TQ4N1C02D
3.0
3.1
3.1
3.1
3.1
3.2
3.2
3.2
3.2
3.3
3.3
3.3
3.3
3.4
3.4
3.4
3.4
3.5
3.5
3.5
3.5
3.6
3.6
3.6
3.6
3.7
3.7
3.7
3.7
3.8
3.8
3.8
3.8
3.9
3.9
3.9
3.9
4.0
4.0
4.0
4.0
4.1
4.1
4.1
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
0.45
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
12.2
12.0
12.0
12.0
12.0
12.6
12.6
12.6
12.6
12.2
12.2
12.2
12.2
12.5
12.5
12.5
12.5
12.1
12.1
12.1
12.1
11.5
11.5
11.5
11.5
11.4
11.4
11.4
11.4
11.1
11.1
11.1
11.1
10.7
10.7
10.7
10.7
10.5
10.5
10.5
10.5
10.3
10.3
10.3
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
9.7
360
290
290
290
290
290
290
290
290
290
290
290
290
280
280
280
280
280
280
280
280
280
280
280
280
270
270
270
270
270
270
270
270
270
270
270
270
270
270
270
270
270
270
270
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
Customer
P5/16
Self-resonant
frequency
(GHz)
Inductance
Nominal
DC
resistance
(Ω max.)
Rated
current
(mA)
Murata
Q
(Min.)
Part number
Part number
*Typical
value
Lower
limit
value
(nH)
Tolerance
LQP02TQ4N1C02L
LQP02TQ4N2B02D
LQP02TQ4N2B02L
LQP02TQ4N2C02D
LQP02TQ4N2C02L
LQP02TQ4N3H02D
LQP02TQ4N3H02L
LQP02TQ4N3J02D
LQP02TQ4N3J02L
LQP02TQ4N7H02D
LQP02TQ4N7H02L
LQP02TQ4N7J02D
LQP02TQ4N7J02L
LQP02TQ5N1H02D
LQP02TQ5N1H02L
LQP02TQ5N1J02D
LQP02TQ5N1J02L
LQP02TQ5N6H02D
LQP02TQ5N6H02L
LQP02TQ5N6J02D
LQP02TQ5N6J02L
LQP02TQ6N2H02D
LQP02TQ6N2H02L
LQP02TQ6N2J02D
LQP02TQ6N2J02L
LQP02TQ6N8H02D
LQP02TQ6N8H02L
LQP02TQ6N8J02D
LQP02TQ6N8J02L
LQP02TQ7N5H02D
LQP02TQ7N5H02L
LQP02TQ7N5J02D
LQP02TQ7N5J02L
LQP02TQ8N2H02D
LQP02TQ8N2H02L
LQP02TQ8N2J02D
LQP02TQ8N2J02L
LQP02TQ9N1H02D
LQP02TQ9N1H02L
LQP02TQ9N1J02D
LQP02TQ9N1J02L
LQP02TQ10NH02D
LQP02TQ10NH02L
LQP02TQ10NJ02D
4.1
4.2
4.2
4.2
4.2
4.3
4.3
4.3
4.3
4.7
4.7
4.7
4.7
5.1
5.1
5.1
5.1
5.6
5.6
5.6
5.6
6.2
6.2
6.2
6.2
6.8
6.8
6.8
6.8
7.5
7.5
7.5
7.5
8.2
8.2
8.2
8.2
9.1
9.1
9.1
9.1
10
C: ±0.2 nH
B: ±0.1 nH
B: ±0.1 nH
C: ±0.2 nH
C: ±0.2 nH
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.2
1.2
1.2
1.2
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.7
1.7
1.7
1.7
1.7
1.7
1.7
10.3
11.0
11.0
11.0
11.0
10.8
10.8
10.8
10.8
9.6
9.6
9.6
9.6
9.2
9.2
9.2
9.2
9.4
9.4
9.4
9.4
8.5
8.5
8.5
8.5
7.8
7.8
7.8
7.8
8.1
8.1
8.1
8.1
7.8
7.8
7.8
7.8
7.0
7.0
7.0
7.0
6.5
6.5
6.5
9.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
8.5
8.5
8.5
8.5
7.8
7.8
7.8
7.8
7.8
7.8
7.8
7.8
7.2
7.2
7.2
7.2
6.6
6.6
6.6
6.6
6.6
6.6
6.6
6.6
6.6
6.6
6.6
6.6
5.9
5.9
5.9
5.9
5.5
5.5
5.5
270
270
270
270
270
270
270
270
270
270
270
270
270
250
250
250
250
230
230
230
230
220
220
220
220
210
210
210
210
200
200
200
200
190
190
190
190
170
170
170
170
170
170
170
10
10
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
Customer
P6/16
Self-resonant
frequency
(GHz)
Inductance
Nominal
DC
resistance
(Ω max.)
Rated
current
(mA)
Murata
Q
(Min.)
Part number
Part number
*Typical
value
Lower
limit
value
(nH)
Tolerance
LQP02TQ10NJ02L
LQP02TQ11NH02D
LQP02TQ11NH02L
LQP02TQ11NJ02D
LQP02TQ11NJ02L
LQP02TQ12NH02D
LQP02TQ12NH02L
LQP02TQ12NJ02D
LQP02TQ12NJ02L
LQP02TQ13NH02D
LQP02TQ13NH02L
LQP02TQ13NJ02D
LQP02TQ13NJ02L
LQP02TQ14NH02D
LQP02TQ14NH02L
LQP02TQ14NJ02D
LQP02TQ14NJ02L
LQP02TQ15NH02D
LQP02TQ15NH02L
LQP02TQ15NJ02D
LQP02TQ15NJ02L
LQP02TQ16NH02D
LQP02TQ16NH02L
LQP02TQ16NJ02D
LQP02TQ16NJ02L
LQP02TQ17NH02D
LQP02TQ17NH02L
LQP02TQ17NJ02D
LQP02TQ17NJ02L
LQP02TQ18NH02D
LQP02TQ18NH02L
LQP02TQ18NJ02D
LQP02TQ18NJ02L
LQP02TQ19NH02D
LQP02TQ19NH02L
LQP02TQ19NJ02D
LQP02TQ19NJ02L
LQP02TQ20NH02D
LQP02TQ20NH02L
LQP02TQ20NJ02D
LQP02TQ20NJ02L
LQP02TQ21NH02D
LQP02TQ21NH02L
LQP02TQ21NJ02D
10
11
11
11
11
12
12
12
12
13
13
13
13
14
14
14
14
15
15
15
15
16
16
16
16
17
17
17
17
18
18
18
18
19
19
19
19
20
20
20
20
21
21
21
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
H: ±3%
H: ±3%
J: ±5%
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
8
1.7
1.9
1.9
1.9
1.9
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
3.2
3.2
3.2
6.5
5.9
5.9
5.9
5.9
5.7
5.7
5.7
5.7
5.6
5.6
5.6
5.6
5.1
5.1
5.1
5.1
5.1
5.1
5.1
5.1
4.9
4.9
4.9
4.9
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
4.4
5.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.7
2.7
2.7
2.7
2.7
2.7
2.7
2.7
2.3
2.3
2.3
170
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
120
120
120
8
8
8
8
8
8
8
8
8
8
8
8
8
8
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
Customer
P7/16
Self-resonant
frequency
(GHz)
Inductance
Nominal
DC
resistance
(Ω max.)
Rated
current
(mA)
Murata
Q
(Min.)
Part number
Part number
*Typical
value
Lower
limit
value
(nH)
Tolerance
LQP02TQ21NJ02L
LQP02TQ22NH02D
LQP02TQ22NH02L
LQP02TQ22NJ02D
LQP02TQ22NJ02L
21
22
22
22
22
J: ±5%
H: ±3%
H: ±3%
J: ±5%
J: ±5%
8
8
8
8
8
3.2
3.2
3.2
3.2
3.2
4.4
4.4
4.4
4.4
4.4
2.3
2.3
2.3
2.3
2.3
120
120
120
120
120
* Typical value is actual performance.
4. Testing Conditions
Unless otherwise specified
Temperature: ordinary temperature (15°C to 35°C)
Humidity: ordinary humidity [25% to 85% (RH)]
In case of doubt
Temperature: 20°C±2°C
Humidity: 60% to 70% (RH)
Atmospheric pressure: 86 kPa to 106 kPa
5. Appearance and Dimensions
Unit mass (typical value): 0.05 mg
6. Marking
7. Electrical Performance
No.
Item
Specification
Meet chapter 3 ratings.
Meet chapter 3 ratings.
Test method
Measuring equipment: Keysight E4991A or the
equivalent
7.1 Inductance
7.2 Q
Measuring frequency: 500 MHz
Measuring conditions:
Measurement signal level: Approx. 0 dBm
Electrical length: 27.3 mm
Measuring fixture: Keysight 16196D
Position the chip coil under test as shown in the
measuring example below and connect it to the
electrode by applying weight.
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
No. Item
P8/16
Specification
Test method
Measurement example:
Product insertion hole: ø0.3 mm
Measuring method: see "Electrical performance:
Measuring method for inductance/Q" in the Appendix.
Measuring equipment: digital multimeter
Measuring equipment: Keysight N5230A or the
equivalent
7.3 DC resistance
7.4 Self-resonant
frequency
Meet chapter 3 ratings.
Meet chapter 3 ratings.
7.5 Rated current
Product temperature rise: 25°C max.
Apply the rated current specified in chapter 3.
8. Mechanical Performance
No.
Item
Specification
Test method
8.1 Shear test
No significant mechanical damage or no Test substrate: glass-epoxy substrate
sign of electrode peeling off shall be
observed.
Applying force: 1 N
Holding time: 5 s±1 s
Force application direction:
8.2 Bending test
No significant mechanical damage or no Test substrate: glass-epoxy substrate (100 mm × 40
sign of electrode peeling off shall be
observed.
mm × 0.8 mm)
Pressurizing speed: 1 mm/s
Pressure jig: R340
Deflection: 1 mm
Holding time: 30 s
8.3 Vibration
Appearance shall have no significant
mechanical damage.
Oscillation frequency: 10 Hz to 2000 Hz to 10 Hz, for
approx. 20 min
Inductance change rate: within ±10%
Total amplitude: total amplitude of 1.5 mm or
acceleration amplitude of 196 m/s2, whichever is
smaller
Test time: 3 directions perpendicular to each other, 2 h
for each direction (6 h in total)
8.4 Solderability
90% or more of the outer electrode shall Flux: immersed in ethanol solution with a rosin content
be covered with new solder seamlessly. of 25(wt)% for 5 s to 10 s
Solder: Sn-3.0Ag-0.5Cu solder
Pre-heating: 150°C±10°C/60 s to 90 s
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
No. Item
P9/16
Specification
Test method
Solder temperature: 240°C±5°C
Immersion time: 3 s±1 s
8.5 Resistance to
soldering heat
Appearance: No significant mechanical
damage shall be observed.
Flux: immersed in ethanol solution with a rosin content
of 25(wt)% for 5 s to 10 s
Inductance change rate: within ±10%
Solder: Sn-3.0Ag-0.5Cu solder
Pre-heating: 150°C±10°C/60 s to 90 s
Solder temperature: 260°C±5°C
Immersion time: 5 s±1 s
Post-treatment: left at a room condition for 24 h±2 h
9. Environmental Performance
The product is soldered on a glass-epoxy substrate for test.
No.
Item
Specification
Test method
9.1 Heat resistance
9.2 Cold resistance
9.3 Humidity
Appearance: No significant mechanical Temperature: 125°C±2°C
damage shall be observed.
Test time: 1000 h (+48 h, -0 h)
Inductance change rate: within ±10%
Post-treatment: left at a room condition for 24 h±2 h
Appearance: No significant mechanical Temperature: -55°C±3°C
damage shall be observed.
Test time: 1000 h (+48 h, -0 h)
Inductance change rate: within ±10%
Post-treatment: left at a room condition for 24 h±2 h
Appearance: No significant mechanical Temperature: 40°C±2°C
damage shall be observed.
Humidity: 90% (RH) to 95% (RH)
Inductance change rate: within ±10%
Test time: 1000 h (+48 h, -0 h)
Post-treatment: left at a room condition for 24 h±2 h
9.4 Temperature cycle Appearance: No significant mechanical Single cycle conditions:
damage shall be observed.
Step 1: -55°C±2°C/30 min±3 min
Inductance change rate: within ±10%
Step 2: ordinary temperature/10 min to 15 min
Step 3: +125°C±2°C/30 min±3 min
Step 4: ordinary temperature/10 min to 15 min
Number of testing: 10 cycles
Post-treatment: left at a room condition for 24 h±2 h
10. Specification of Packaging
10.1 Appearance and dimensions of tape
• 8 mm width/paper tape
A
B
t
(0.23)
(0.45)
0.39 max.
(in mm)
• 4 mm width/plastic tape
A
B
t
(0.22)
(0.47)
(0.23)
t'
0.20±0.05
(in mm)
* The dimensions of the cavity are measured at its bottom.
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
P10/16
10.2 Taping specifications
Packing quantity
(Standard quantity)
20000 pcs/reel (carrier tape: 8 mm width, 2 mm pitch)
40000 pcs/reel (carrier tape: 4 mm width, 1 mm pitch)
Packing method
Feed hole position
Joint
The products are placed in cavities of a carrier tape and sealed by a cover tape (top tape and bottom
tape when the cavities of the carrier tape are punched type).
The feed holes on the carrier tape are on the right side when the cover tape (top tape when the cavities
of the carrier tape are punched type) is pulled toward the user.
The carrier tape and cover tape (top tape when the cavities of the carrier tape are punched type) are
seamless.
Number of missing
products
Number of missing products within 0.1% of the number per reel or 1 pc., whichever is greater, and are
not continuous. The specified quantity per reel is kept.
10.3 Break down force of tape
Cover tape (or top tape)
5 N min.
5 N min.
Bottom tape (only when the cavities of the carrier tape are punched type)
10.4 Peeling off force of tape
Speed of peeling off
Peeling off force
300 mm/min
0.1 N to 0.6 N (The lower limit is for typical value.)
10.5 Dimensions of leader section, trailer section and reel
A vacant section is provided in the leader (start) section and trailer (end) section of the tape for the product. The leader
section is further provided with an area consisting only of the cover tape (or top tape). (See the diagram below.)
• 8 mm width carrier tape
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
• 4 mm width carrier tape
P11/16
10.6 Marking for reel
Customer part number, Murata part number, inspection number (*1), RoHS marking (*2), quantity, etc.
*1 Expression of inspection No.: (1) Factory code
□□
(1)
○○○○
(2)
(2) Date
First digit: year/last digit of year
(3)
Second digit: month/Jan. to Sep.→1 to 9, Oct. to Dec.→O, N, D
Third, Fourth digit: day
(3) Serial No.
*2 Expression of RoHS marking: (1) RoHS regulation conformity
ROHS-
Y
()
(2) Murata classification number
(1)
(2)
10.7 Marking on outer box (corrugated box)
Customer name, purchasing order number, customer part number, Murata part number, RoHS marking (*2), quantity, etc.
10.8 Specification of outer box
Dimensions of outer box
Tape width Standard reel quantity
(mm)
(mm)
in outer box(reel)
Label
W
D
H
4
8
10
5
H
186
186
93
D
* Above outer box size is typical. It depends on a quantity of an
order.
W
11.
Caution
11.1 Restricted applications
Please contact us before using our products for the applications listed below which require especially high reliability for the
prevention of defects which might directly cause damage to the third party's life, body or property.
(1) Aircraft equipment
(2) Aerospace equipment
(3) Undersea
equipment
(4) Power plant control
equipment
(5) Medical equipment
(6) Transportation equipment (vehicles, (7) Traffic signal
trains, ships, etc.) equipment
(8) Disaster/crime
prevention
equipment
(9) Data-processing
equipment
(10) Applications of similar complexity and/or reliability
requirements to the applications listed in the above
11.2 Precautions on rating
Avoid using in exceeded the rated temperature range, rated voltage, or rated current.
Usage when the ratings are exceeded could lead to wire breakage, burning, or other serious fault.
11.3 Inrush current
If an inrush current (or pulse current or rush current) that significantly exceeds the rated current is applied to the product,
overheating could occur, resulting in wire breakage, burning, or other serious fault.
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
P12/16
12. Precautions for Use
This product is for use only with reflow soldering. It is designed to be mounted by soldering. If you want to use other mounting
method, for example, using a conductive adhesive, please consult us beforehand.
Also, if repeatedly subjected to temperature cycles or other thermal stress, due to the difference in the coefficient of thermal
expansion with the mounting substrate, the solder (solder fillet part) in the mounting part may crack.
The occurrence of cracks due to thermal stress is affected by the size of the land where mounted, the solder volume, and the
heat dissipation of the mounting substrate. Carefully design it when a large change in ambient temperature is assumed.
12.1. Land dimensions
The following diagram shows the recommended land dimensions for reflow soldering:
a
b
c
0.20
0.56
0.16
(in mm)
12.2 Flux and solder used
Flux
• Use a rosin-based flux.
• Do not use a highly acidic flux with a halide content exceeding 0.2(wt)% (chlorine conversion value).
• Do not use a water-soluble flux.
Solder
• Use Sn-3.0Ag-0.5Cu solder.
• Standard thickness of solder paste: 50 μm to 65 μm
If you want to use a flux other than the above, please consult our technical department.
12.3 Soldering conditions (reflow)
• Pre-heating should be in such a way that the temperature difference between solder and product surface is limited to 150°C
max.
Cooling into solvent after soldering also should be in such a way that the temperature difference is limited to 100°C max.
Insufficient pre-heating may cause cracks on the product, resulting in the deterioration of product quality.
• Standard soldering profile and the limit soldering profile is as follows.
The excessive limit soldering conditions may cause leaching of the electrode and/or resulting in the deterioration of product
quality.
Temp.
(℃)
260℃
230℃
Limit Profile
245℃±3℃
220℃
180
150
Standard Profile
30s~60s
60s max.
90s±30s
Time.(s)
Standard profile
Limit profile
Pre-heating
150°C to 180°C/90 s±30 s
Above 220°C/30 s to 60 s
245°C±3°C
150°C to 180°C/90 s±30 s
Above 230°C/60 s max.
260°C/10 s
Heating
Peak temperature
Number of reflow cycles
2 times
2 times
12.4 Reworking with soldering iron
Do not perform reworking with a soldering iron on this product.
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
P13/16
12.5 Solder volume
Solder shall be used not to increase the volume too much.
An increased solder volume increases mechanical stress on the product. Exceeding solder volume may cause the failure of
mechanical or electrical performance.
12.6 Product's location
The following shall be considered when designing and laying out PCBs.
(1) PCB shall be designed so that products are not subject to mechanical stress due to warping the board.
[Products direction]
Products shall be located in the sideways direction (length: a < b) to the mechanical stress.
a
b
Poor example
〈
〉
Good example
〈
〉
(2) Components location on PCB separation
It is effective to implement the following measures, to reduce stress in separating the board.
It is best to implement all of the following three measures; however, implement as many measures as possible to reduce
stress.
Contents of measures
Stress level
A > D*1
A > B
(1) Turn the mounting direction of the component parallel to the
board separation surface.
(2) Add slits in the board separation part.
(3) Keep the mounting position of the component away from the
board separation surface.
A > C
*1 A > D is valid when stress is added vertically to the perforation as with hand separation.
If a cutting disc is used, stress will be diagonal to the PCB, therefore A > D is invalid.
(3) Mounting components near screw holes
When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during the
tightening of the screw.
Mount the component in a position as far away from the screw holes as possible.
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
P14/16
12.7 Handling of substrate
(1) The stress applied to the chip varies depending on the material and construction of the mounted substrate.
If the coefficients of thermal expansion for the substrate and chip vary significantly, the difference in thermal expansion and
shrinkage could cause cracks to form in the chip.
We assume that the products are mounted on glass-epoxy substrate. Assessment has not been conducted on substrates
where the coefficient of thermal expansion varies significantly from glass-epoxy substrates. If mounting on these
substrates, be sure to conduct full assessments before use.
(2) After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the
substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the
substrate.
Excessive mechanical stress may cause cracking in the product.
Also, if mounting on flexible substrates, excessive mechanical stress could be applied to the chip by even slight bending or
twisting when handling this substrate, and so please conduct full assessments before use.
Bending
Twisting
12.8 Cleaning
The product shall be cleaned under the following conditions.
(1) The cleaning temperature shall be 60°C max. If isopropyl alcohol (IPA) is used, the cleaning temperature shall be 40°C
max.
(2) Perform ultrasonic cleaning under the following conditions. Exercise caution to prevent resonance phenomenon in
mounted products and the PCB.
Item
Power
Requirement
20 W/L max.
Time
5 min max.
Frequency
(3) Cleaner
28 kHz to 40 kHz
Alcohol-based cleaner: IPA
Aqueous agent: PINE ALPHA ST-100S
(4) There shall be no residual flux or residual cleaner. When using aqueous agent, rinse the product with deionized water
adequately and completely dry it so that no cleaner is left.
* For other cleaning, consult our technical department.
12.9 Storage and transportation
Storage period
Use the product within 12 months after delivery.
If you do not use the product for more than 12 months, check solderability before using it.
Storage conditions • The products shall be stored in a room not subject to rapid changes in temperature and
humidity. The recommended temperature range is -10°C to +40°C. The recommended relative
humidity range is 15% to 85%.
Keeping the product in corrosive gases, such as sulfur, chlorine gas or acid may cause the poor
solderability.
• Do not place the products directly on the floor; they should be placed on a palette so that they
are not affected by humidity or dust.
• Avoid keeping the products in a place exposed to direct sunlight, heat or vibration.
• Do not keep products in bulk packaging. Bulk storage could result in collisions between the
products or between the products and other parts, resulting in chipping or wire breakage.
• Avoid storing the product by itself bare (i.e. exposed directly to air).
Transportation
Excessive vibration and impact reduces the reliability of the products. Exercise caution when
handling the products.
12.10 Resin coating (including moisture-proof coating)
Before applying any resin coating, please consult our technical department.
12.11 Mounting conditions
Check the mounting condition before using.
Using mounting conditions (nozzles, equipment conditions, etc.) that are not suitable for products may lead to pick up errors,
misalignment, or damage to the product.
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
P15/16
12.12 Operating environment
Do not use this product under the following environmental conditions as it may cause deterioration of product quality.
(1) In the corrodible atmosphere such as acidic gases, alkaline gases, chlorine, sulfur gases, organic gases and etc.
(the sea breeze, Cl2, H2S, NH3, SO2, NO2, etc)
(2) In the atmosphere where liquid such as organic solvent, may splash on the products.
(3) In the atmosphere where the temperature/humidity changes rapidly and it is easy to dew.
12.13 Mounting density
If this product is placed near heat-generating products, be sure to implement sufficient heat-dissipating measures.
If this product is subjected to a significant amount of heat from other products, this could adversely affect product quality,
resulting in a circuit malfunction or failure of the mounted section. Also, be sure that the product is used in a manner so that
the heat that the product is subjected to from other products does not exceed the upper limit of the rated operating
temperature for the product.
13.
Note
(1) Please make sure that your product has been evaluated in view of your specifications with our product being mounted to
your product.
(2) You are requested not to use our product deviating from the reference specifications.
(3) The contents of this reference specification are subject to change without advance notice. Please approve our product
specifications or transact the approval sheet for product specifications before ordering.
MURATA MFG CO., LTD
Spec No.: JELF243C_0019K-01
P16/16
Appendix
Electrical performance: Measuring method for inductance/Q (Q measurement is applicable only when the Q value is included
in the rating table.)
Perform measurement using the method described below. (Perform correction for the error deriving from the measuring
terminal.)
(1) Residual elements and stray elements of the measuring terminal can be expressed by the F parameter for the 2-pole
terminal as shown in the figure below.
(2) The product's impedance value (Zx) and measured impedance value (Zm) can be expressed as shown below, by using
the respective current and voltage for input/output.
V1
I1
V2
I2
Zm=
Zx=
(3) Thus, the relationship between the product's impedance value (Zx) and measured impedance value (Zm) is as follows.
Here,
α = D/A = 1
β = B/D = Zsm - (1 - Yom Zsm) Zss
Γ = C/A = Yom
Zm-β
Zx=α
1-ZmΓ
Zsm: measured impedance of short chip
Zss: residual impedance of short chip (0.110 nH)
Yom: measured admittance when measuring
terminal is open
(4) Calculate inductance Lx and Qx using the equations shown below.
Im(Zx)
Lx: inductance of chip coil
Qx: Q of chip coil
Lx=
2πf
Im(Zx)
Qx=
f: measuring frequency
Re(Zx)
MURATA MFG CO., LTD
相关型号:
©2020 ICPDF网 联系我们和版权申明