LQH44NN331K03# [MURATA]
;型号: | LQH44NN331K03# |
厂家: | muRata |
描述: | |
文件: | 总9页 (文件大小:316K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SpecNo.JELF243A-0097E-01
P1/9
CHIP COIL(CHIP INDUCTORS) LQH44NN□□□□03□ REFERENCE SPECIFICATION
1. Scope
This reference specification applies to LQH44NN_03 Series, Chip coil (Chip Inductors).
2. Part Numbering
(ex)
LQ
H
44
N
N
R51
M
0
3
L
Product ID Structure Dimension Applications Category Inductance Tolerance Features Electrode Packaging
(L×W)
and
Characteristics
L:Taping(φ180mm/reel)
K:Taping (φ330mm/reel)
3. Rating
・Operating Temperature Range.
(Ambient temperature; Self-temperature rise is not included)
(Product temperature; Self- temperature rise is included)
・Storage Temperature Range.
-40 to +85°C
-40 to +125°C
-40 to +125°C
Self
Rated
Inductance
DC
Resistance
Customer
Part Number
MURATA
Part Number
Resonant
Current
Frequency
(A)
(µH)
Tolerance
(Ω)
(MHz min)
LQH44NNR51M03L
LQH44NNR51M03K
LQH44NNR74M03L
LQH44NNR74M03K
LQH44NN1R0M03L
LQH44NN1R0M03K
LQH44NN1R5M03L
LQH44NN1R5M03K
LQH44NN2R2M03L
LQH44NN2R2M03K
LQH44NN3R3M03L
LQH44NN3R3M03K
LQH44NN4R7M03L
LQH44NN4R7M03K
LQH44NN5R0K03L
LQH44NN5R0K03K
LQH44NN6R8K03L
LQH44NN6R8K03K
LQH44NN100K03L
LQH44NN100K03K
LQH44NN150K03L
LQH44NN150K03K
LQH44NN220K03L
LQH44NN220K03K
LQH44NN330K03L
LQH44NN330K03K
LQH44NN470K03L
LQH44NN470K03K
LQH44NN680K03L
LQH44NN680K03K
LQH44NN101K03L
LQH44NN101K03K
0.51
0.0075±30%
160
150
90
4.50
3.50
3.30
3.20
2.50
2.25
1.95
1.95
1.60
1.30
1.10
0.95
0.76
0.64
0.53
0.30
0.74
1.0
1.5
2.2
3.3
4.7
5.0
6.8
10
0.011±30%
0.012±30%
0.016±30%
0.019±20%
0.024±30%
0.040±30%
0.040±30%
0.051±30%
0.067±30%
0.100±30%
0.170±30%
0.210±30%
0.330±30%
0.410±30%
0.540±30%
M:±20%
70
55
34.8
23.4
23.4
19.8
23.5
11.5
14
15
22
K:±10%
33
12
47
10
68
8.0
100
6.3
MURATA MFG.CO., LTD
SpecNo.JELF243A-0097E-01
P2/9
Self
Inductance
DC
Resistance
(Ω)
Rated
Current
(A)
Customer
MURATA
Resonant
Frequency
(MHz min)
Part Number
Part Number
(µH)
Tolerance
LQH44NN151K03L
LQH44NN151K03K
LQH44NN221K03L
LQH44NN221K03K
LQH44NN331K03L
LQH44NN331K03K
LQH44NN471K03L
LQH44NN471K03K
150
220
330
470
0.920±30%
1.20±30%
1.76±30%
2.23±30%
5.2
3.9
3.0
2.7
0.26
0.21
K:±10%
0.18
0.145
When applied Rated current to the Products, Inductance will be within ±30% of initial Inductance value.
When applied Rated current to the Products, temperature rise caused by self-generated heat shall be limited
to 40°C max.
4. Testing Conditions
《Unless otherwise specified》
Temperature : Ordinary Temperature (15 to 35°C)
Humidity : Ordinary Humidity (25 to 85 % (RH))
《In case of doubt》
Temperature
Humidity
: 20 ± 2°C
: 60 to 70 % (RH)
Atmospheric Pressure : 86 to 106 kPa
5. Appearance and Dimensions
4.0±0.2
4.0±0.2
(0.2)
※No Marking.
■Unit Mass (Typical value)
0.26g
(in mm)
1.1±0.2
1.1±0.2
6. Electrical Performance
No. Item
Specification
Test Method
6.1 Inductance
Inductance shall meet item 3.
Measuring Equipment:KEYSIGHT 4284A or equivalent
Measuring Frequency:1kHz
6.2 DC Resistance
DC Resistance shall meet item 3.
S.R.F shall meet item 3.
Measuring Equipment:Digital multi meter
6.3 Self Resonant
Frequency(S.R.F)
Measuring Equipment:KEYSIGHT E4991A or equivalent
MURATA MFG.CO., LTD
SpecNo.JELF243A-0097E-01
P3/9
7. Mechanical Performance
No.
Item
Specification
Test Method
7.1 Shear Test
Chip coil shall not be damaged.
Substrate:Glass-epoxy substrate
Applied Direction:
Chip coil
F
Substrate
Force:10N
Hold Duration:5±1s
Bending Test
7.2
Chip coil shall not be damaged.
Substrate:Glass-epoxy substrate
(100×40×1.0mm)
Speed of Applying Force:0.5mm / s
Deflection:2mm
Hold Duration:5seconds.
Pressure jig
R230
F
Deflection
45
45
Product
(in mm)
Vibration
7.3
Chip coil shall not be damaged.
Oscillation Frequency:10~2000~10Hz for 20minutes
Total Amplitude:1.5mm or Acceleration amplitude
196m/s2 whichever is smaller.
Testing Time:A period of 2 hours in each of 3 mutually
perpendicular directions. (Total 6 hours)
Solderability
7.4
shall be at least 90% covered with
new solder coating.The wetting area
of the electrode
Flux:Ethanol solution of rosin,25(wt)%
(Immersed for 5s to 10s)
Solder:Sn-3.0Ag-0.5Cu
Pre-Heating:150±10°C / 60 to 90seconds
Solder Temperature:240±5°C
Immersion Time:3±1 s
Resistance to
7.5
Appearance:No damage
Inductance Change:within ±10%
Flux:Ethanol solution of rosin,25(wt)%
(Immersed for 5s to 10s)
Solder:Sn-3.0Ag-0.5Cu
Soldering
Heat
Pre-Heating:150±10°C / 60 to 90seconds
Solder Temperature:270±5°C
Immersion Time:10±1 s
Then measured after exposure in the room condition for
24±2 hours.
MURATA MFG.CO., LTD
SpecNo.JELF243A-0097E-01
P4/9
8. Environmental Performance (It shall be soldered on the substrate.)
No.
Item
Specification
Test Method
8.1 Heat Resistance
8.2 Cold Resistance
8.3 Humidity
Appearance:No damage
Inductance Change:within ± 10% Time:1000h (+48h , -0h)
DC Resistance Change:
within ± 10%
Temperature:85±2°C
Then measured after exposure in the room condition
for 24±2 hours.
Temperature:-40±2°C
Time:1000h (+48h , -0h)
Then measured after exposure in the room condition
for 24±2 hours.
Temperature:70±2°C
Humidity:90~95%(RH)
Time:1000h (+48h , -0h)
Then measured after exposure in the room condition
for 24±2 hours.
8.4 Temperature
Cycle
1 cycle:
1 step:-40±2°C / 30±3 minutes
2 step:Ordinary temp. / 10 to 15 minutes
3 step:+85±2°C / 30±3 min
4 step:Ordinary temp. / 10 to 15 minutes
Total of 10 cycles
Then measured after exposure in the room condition
for 24±2 hours.
9. Specification of Packaging
9.1 Appearance and Dimensions of plastic tape
+0.1
-0
φ 1.5
4.0±0.1
2.0±0.05
(0.4)
8.0±0.1
(in mm)
4.7±0.1
Direction of feed
*Lead-in/out wire
4.3±0.1
Dimension of the Cavity is measured at the bottom side.
9.2 Specification of Taping
(1) Packing quantity (standard quantity)
φ180 mm reel: 250 pcs. / reel
φ330 mm reel:1500 pcs. / reel
(2) Packing Method
Products shall be packed in the each embossed cavity of plastic tape and sealed by cover tape.
(3) Sprocket hole
The sprocket holes are to the right as the tape is pulled toward the user.
(4) Spliced point
Plastic tape and Cover tape has no spliced point.
(5) Missing components number
Missing components number within 0.025 % of the number per reel or 1 pc., whichever is greater,
and are not continuous. The specified quantity per reel is kept.
MURATA MFG.CO., LTD
SpecNo.JELF243A-0097E-01
P5/9
9.3 Pull Strength
Embossed carrier tape
10N min.
5N min.
Cover tape
9.4 Peeling off force of cover tape
165 to 180 degree
F
Cover tape
Plastic tape
Speed of Peeling off
Peeling off force
300mm/min
0.2 to 0.7N
(minimum value is typical)
9.5 Dimensions of Leader-tape, Trailer and Reel
There shall be leader-tape (cover tape) and trailer-tape (empty tape) as follows.
« Packaging Code : L (φ180mm reel) »
Trailer : 160 min.
2.0±0.5
Leader
190 min
Empty tape Cover tape
Label
210 min
13.0±0.2
60±1
0
21.0±0.8
13.0±10
17.0±1.4
Direction of feed
180± 0
(in mm)
3
« Packaging Code : K (φ330mm reel) »
Trailer
160min.
Leader
210min.
Cover tape
2.0±0.5
190min.
Empty Tape
Label
50min.
13.5±1.0
17.5±1.0
13.0±0.2
21.0±0.8
Direction of feed
(in mm)
330±2.0
9.6 Marking for reel
Customer part number, MURATA part number, Inspection number(1), RoHS marking(2), Quantity etc ・・・
1) <Expression of Inspection No.>
□□OOOO
(1) (2) (3
)
(1) Factory Code
(2) Date
First digit
: Year / Last digit of year
Second digit
: Month / Jan. to Sep. 1 to 9, Oct. to Dec. O, N, D
Third, Fourth digit : Day
(3) Serial No.
2) « Expression of RoHS marking »
ROHS – Y (△)
(1) (2)
(1) RoHS regulation conformity
(2) MURATA classification number
9.7 Marking for Outside package (corrugated paper box)
Customer name, Purchasing order number, Customer part number, MURATA part number, RoHS marking (2) ,
Quantity, etc ・・・
MURATA MFG.CO., LTD
SpecNo.JELF243A-0097E-01
P6/9
9.8. Specification of Outer Case
Outer Case Dimensions(mm)
Standard Reel Quantity
in Outer Case (Reel)
Reel
W
D
H
Label
φ180mm
φ330mm
186
340
186
340
93
95
4
4
H
D
Above Outer Case size is typical. It depends on a quantity of an order.
W
10. Caution
10.1 Limitation of Applications
Please contact us before using our products for the applications listed below which require especially high reliability for
the prevention of defects which might directly cause damage to the third party's life, body or property.
(1) Aircraft equipment
(6) Transportation equipment (vehicles, trains, ships, etc.)
(7) Traffic signal equipment
(8) Disaster prevention / crime prevention equipment
(9) Data-processing equipment
(10) Applications of similar complexity and /or reliability requirements
to the applications listed in the above
(2) Aerospace equipment
(3) Undersea equipment
(4) Power plant control equipment
(5) Medical equipment
10.2 Corrosive gas
Please refrain from use since contact with environments with corrosive gases (sulfur gas [hydrogen sulfide, sulfur dioxide,
etc.], chlorine, ammonia, etc.) or oils (cutting oil, silicone oil, etc.) that have come into contact with the previously stated
corrosive gas environment will result in deterioration of product quality or an open from deterioration due
11. Notice
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
11.1 Land pattern designing (Reflow Soldering)
Recommended land patterns for reflow soldering are as follows:
These have been designed for Electric characteristics and solderability.
Please follow the recommended patterns. Otherwise, their performance which includes electrical performance or
solderability may be affected, or result to "position shift" in soldering process.
Land
Chip Colil
4.4
Solder Resist
3.0
(in mm)
1.3
1.55
11.2 Flux, Solder
・Use rosin-based flux.
Flux
・Don’t use highly acidic flux with halide content exceeding 0.2(wt)% (chlorine conversion value).
・Don’t use water-soluble flux.
・Use Sn-3.0Ag-0.5Cu solder.
・Standard thickness of solder paste : 100μm to 150μm
Solder
Other flux (except above) Please contact us for details, then use.
MURATA MFG.CO., LTD
SpecNo.JELF243A-0097E-01
P7/9
11.3 Soldering conditions (Reflow)
・Pre-heating should be in such a way that the temperature difference between solder and product surface is limited to
100°C max. Cooling into solvent after soldering also should be in such a way that the temperature difference is
limited to 100°C max.
Insufficient pre-heating may cause cracks on the product, resulting in the deterioration of product quality.
・Standard soldering profile and the limit soldering profile is as follows.
The excessive limit soldering conditions may cause leaching of the electrode and / or resulting in the deterioration of
product quality.
Reflow soldering profile
Temp.
(℃)
260℃
230℃
Limit Profile
245℃±3℃
220℃
180
150
Standard Profile
30s~60s
60s max.
90s±30s
Time.(s)
Standard Profile
Limit Profile
Pre-heating
150~180°C 、90s±30s
above 220°C、30s~60s above 230°C、60s max.
Heating
Peak temperature
Cycle of reflow
245±3°C
2times
260°C,10s
2 times
11.4 Reworking with soldering iron.
The following conditions must be strictly followed when using a soldering iron.
Pre-heating
150°C,1 min
380°C max.
80W max.
φ3mm max.
3(+1,-0)s
Tip temperature
Soldering iron output
Tip diameter
Soldering time
Times
2 times
Note:Do not directly touch the products with the tip of the soldering iron in order to prevent the crack
on the products due to the thermal shock.
11.5 Solder Volume
・ Solder shall be used not to be exceeded the upper limits as shown below.
・ Accordingly increasing the solder volume, the mechanical stress to Chip is also increased.Exceeding solder volume
may cause the failure of mechanical or electrical performance.
Excessively
Recommendabl
MURATA MFG.CO., LTD
SpecNo.JELF243A-0097E-01
P8/9
11.6 Product's location
The following shall be considered when designing and laying out P.C.B.’s.
(1) P.C.B. shall be designed so that products are not subject to the mechanical stress due to warping the board.
[Products direction]
Electrode
The electorode part of the products should be
located like the picture to the mechanical stress.
(Good example)
(Poor example)
Electrode
(2) Components location on P.C.B. separation.
It is effective to implement the following measures, to reduce stress in separating the board.
It is best to implement all of the following three measures; however, implement as many measures
as possible to reduce stress.
Contents of Measures
Stress Level
(1) Turn the mounting direction of the component parallel to
the board separation surface.
A
A
A
>
>
>
D 1
B
(2) Add slits in the board separation part.
(3) Keep the mounting position of the component away from
the board separation surface.
C
C
Seam
B
1 A > D is valid when stress is added vertically to
the perforation as with Hand Separation.
If a Cutting Disc is used, stress will be diagonal to
the PCB, therefore A > D is invalid.
Electrode
D
A
Slit
Electrode
(3) Mounting Components Near Screw Holes
When a component is mounted near a screw hole,
it may be affected by the board deflection that occurs
during the tightening of the screw. Mount the component
in a position as far away from the screw holes as possible.
Recommended
Screw Hole
11.7 Cleaning Conditions
Products shall be cleaned on the following conditions.
(1) Cleaning temperature shall be limited to 60°C max.(40°C max for IPA.)
(2) Ultrasonic cleaning shall comply with the following conditions with avoiding the resonance
phenomenon at the mounted products and P.C.B.
Power : 20 W / l max.
(3) Cleaner
Frequency : 28kHz to 40kHz
Time : 5 minutes max.
1. Alternative cleaner
・Isopropyl alcohol (IPA)
2. Aqueous agent
・PINE ALPHA ST-100S
(4) There shall be no residual flux and residual cleaner after cleaning.
In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized water in
order to remove the cleaner.
(5) Other cleaning
Please contact us.
11.8 Resin coating
The inductance value may change due to high cure-stress of resin to be used for coating/molding products. An open
circuit issue may occur by mechanical stress caused by the resin, amount/cured shape of resin, or operating condition
etc. Some resin contains some impurities or chloride possible to generate chlorine by hydrolysis under some operating
condition may cause corrosion of wire of coil, leading to open circuit. So, please pay your careful attention when you
select resin in case of coating/molding the products with the resin.Prior to use the coating resin, please make sure no
reliability issue is observed by evaluating products mounted on your board.
MURATA MFG.CO., LTD
SpecNo.JELF243A-0097E-01
P9/9
11.9 Caution for use
・Sharp material such as a pair of tweezers or other material such as bristles of cleaning brush, shall not be touched to
the winding portion to prevent the breaking of wire.
・Mechanical shock should not be applied to the products mounted on the board to prevent the breaking of the core
11.10 Handling of a substrate
After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the
substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to
the substrate.
Excessive mechanical stress may cause cracking in the product.
Bending
Twisting
11.11 Storage and Handling Requirements
(1) Storage period
Use the products within 12 months after delivered.
Solderability should be checked if this period is exceeded.
(2) Storage conditions
・Products should be stored in the warehouse on the following conditions.
Temperature : -10 ~ 40°C
Humidity
: 15 to 85% relative humidity No rapid change on temperature and humidity
The electrode of the products is coated with solder. Don't keep products in corrosive gases such as
sulfur,chlorine gas or acid, or it may cause oxidization of electrode, resulting in poor solderability.
・Products should not be stored on bulk packaging condition to prevent the chipping of the core and the breaking of
winding wire caused by the collision between the products.
・Products should be stored on the palette for the prevention of the influence from humidity, dust and so on.
・Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.
(3) Handling Condition
Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock.
12.
Note
(1) Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your
product.
(2) You are requested not to use our product deviating from the agreed specifications.
(3) The contents of this reference specification are subject to change without advance notice. Please approve our
product specifications or transact the approval sheet for product specifications before ordering.
MURATA MFG.CO., LTD
相关型号:
©2020 ICPDF网 联系我们和版权申明