BLM18BD470BH1D [MURATA]
Ferrite Chip, 1 Function(s), 0.5A, EIA STD PACKAGE SIZE 1608, SMD, 2 PIN;
| 型号： | BLM18BD470BH1D |
| 厂家： | 
muRata |
| 描述： | Ferrite Chip, 1 Function(s), 0.5A, EIA STD PACKAGE SIZE 1608, SMD, 2 PIN |
| 文件： | 总10页 (文件大小：187K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Reference Only
Spec. No. JENF243A-9129B-01
P.1/10
Chip Ferrite Bead BLM18□□□□□(B/J)H1D
Murata Standard Reference Specification [AEC-Q200]
1.Scope
This reference specification applies to Chip Ferrite Bead for Automotive Electronics BLM18_(B/J)H Series based on AEC-
Q200.
2.Part Numbering
(ex.)
BL
M
18
(3)
AG
(4)
121
(5)
B
(6)
H
1
D
(9)
(1)
(2)
(7) (8)
(1)Product ID
(2)Type
(4)Characteristics
(5)Typical Impedance at 100MHz
(7)Category(for Automotive Electronics)
(8)Numbers of Circuit
(3)Dimension (L×Ｗ) (6)Dimension (T) (B:Standard J:Low profile) (9)Packaging (D:Taping)
3.Rating
DC Resistance
( max.)
(refer to below
comment)
Impedance ()
(at 100MHz)
(refer to below comment)
Rated
Current
(mA)
ESD Rank
2:2kV
Customer
Part Number
MURATA
Part Number
Initial
Values
Values After
Typical at 125℃ at 150℃
Testing
0.012
0.015
0.032
0.040
0.040
0.060
0.095
0.145
0.165
0.230
0.28
0.35
0.35
0.40
0.45
0.48
0.60
0.4
4000*1
3300*1
2200*1
1900*1
1900*1
1500*1
1200*1
1000*1
1000*1
800*1
800*1
700*1
700*1
600*1
550*1
500*1
450*1
500*1
300*1
300*1
250*1
250*1
250*1
250*1
200*1
200*1
150*1
150*1
150*1
150*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
10*1
0.007
0.010
0.022
0.030
0.030
0.050
0.080
0.130
0.150
0.200
0.18
0.25
0.25
0.30
0.35
0.38
0.50
0.3
26±25％
30±25％
BLM18KG260JH1D
BLM18KG300JH1D
BLM18KG700JH1D
BLM18KG101JH1D
BLM18KG121JH1D
BLM18KG221BH1D
BLM18KG331BH1D
BLM18KG471BH1D
BLM18KG601BH1D
BLM18KG102BH1D
BLM18AG121BH1D
BLM18AG151BH1D
BLM18AG221BH1D
BLM18AG331BH1D
BLM18AG471BH1D
BLM18AG601BH1D
BLM18AG102BH1D
BLM18BD470BH1D
BLM18BD121BH1D
BLM18BD151BH1D
BLM18BD221BH1D
BLM18BD331BH1D
BLM18BD421BH1D
BLM18BD471BH1D
BLM18BD601BH1D
BLM18BD102BH1D
BLM18BD152BH1D
BLM18BD182BH1D
BLM18BD222BH1D
BLM18BD252BH1D
26
30
70±25％
70
100±25％
120±25％
220±25％
330±25％
470±25％
600±25％
1000±25％
120±25％
150±25％
220±25％
330±25％
470±25％
600±25％
1000±25％
47±25％
100
120
220
330
470
600
1000
120
150
220
330
470
600
1000
47
2
120±25％
150±25％
220±25％
330±25％
420±25％
470±25％
600±25％
1000±25％
1500±25％
1800±25％
2200±25％
2500±25％
120
150
220
330
420
470
600
1000
1500
1800
2200
2500
0.4
0.4
0.5
0.5
0.45
0.5
0.55
0.6
0.55
0.55
0.65
0.85
1.2
0.65
0.65
0.75
0.95
1.3
1.5
1.6
1.5
1.6
1.5
1.6
Operating Temperature : -55°C to +150°C
Storage Temperature : -55°C to +150°C
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9129B-01
P.2/10
(*１)Rated Current is derated as right figure
Rated current
at
depending on the operating temperature.
125℃
Rated current
at 1
150℃
0
85 5
Operating Temperature (°C)
125℃ 150℃
4.Style and Dimensions
1.6±0.15
0.8±0.15
■ Equivalent Circuit
Ｔ
0.4±0.2
Resistance element becomes
dominant at high frequencies.
(
)
: Electrode
(in mm)
■
Unit Mass (Typical value)
BLM18_BH：0.005g
BLM18_JH：0.004g
P/N
T(mm)
BLM18_BH
BLM18_JH
0.8±0.15
0.6±0.15
5.Marking
No marking.
6.Standard Testing Conditions
Unless otherwise specified
In case of doubt
Temperature : Ordinary Temp. (15 °C to 35 °C )
Temperature : 20°C±2 °C
Humidity : Ordinary Humidity (25%(RH) to 85%(RH))
Humidity : 60%(RH) to 70%(RH)
Atmospheric pressure : 86kPa to 106kPa
7.Specifications
7-1.Electrical Performance
No. Item
Specification
Meet item 3.
Test Method
7-1-1 Impedance
Measuring Frequency : 100MHz±1MHz
Measuring Equipment : KEYSIGHT 4991A or the equivalent
Test Fixture : KEYSIGHT 16192A or the equivalent
Measuring Equipment : Digital multi meter
7-1-2 DC Resistance
Meet item 3.
＊Except resistance of the Substrate and Wire
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9129B-01
P.3/10
7-2. Mechanical Performance(based on Table 13 for FILTER EMI SUPPRESSORS/FILTERS)
AEC-Q200 Rev.D issued June. 1 2010
AEC-Q200
Murata Specification / Deviation
Meet Table A after testing.
No.
Stress
Test Method
3
High
1000hours at 150 deg C
Set for 24hours at room
temperature, then measured.
Temperature
Exposure
Table A
Appearance
No damage
Impedance
Change
Within ±50%
(at 100MHz)
DC
Resistance
Meet item 3.
4
Temperature Cycling
1000cycles
Meet Table Ａ after testing.
-55 deg C to +150 deg C
Set for 24hours at room
temperature, then measured.
5
7
Destructive
Physical Analysis
Per EIA469
No electrical tests
No defects
Biased Humidity
1000hours at 85 deg C, 85%RH Meet Table Ｂ after testing.
Apply max rated current.
TableB
Appearance
No damage
Impedance
Change
(at 100MHz)
Within ±30%
(for BLM18KG
Within ±50%)
DC Resistance Meet item 3.
Meet Table A after testing.
If the rated current of parts exceed 10mA,
the operating temperature should be 125 deg C.
8
Operational Life
Apply 150deg C 1000hours
Set for 24hours at room
temperature, then measured
9
External Visual
Visual inspection
No abnormalities
No defects
10
12
Physical Dimension
Meet ITEM 4
（Style and Dimensions）
Resistance to Solvents Per MIL-STD-202
Method 215
Not Applicable
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9129B-01
AEC-Q200
P.4/10
Murata Specification / Deviation
No.
Stress
Test Method
13
Mechanical Shock
Per MIL-STD-202 Method 213
Condition F
Meet Table Ｃ after testing.
Table Ｃ
1500g's (14.7N)/0.5ms/
Half sine
Appearance
Impedance
Change
(at 100MHz)
DC Resistance
No damage
Within ±30%
Meet item 3.
14
15
Vibration
5g's(0.049N) for 20 minutes,
12cycles each of 3 orientations
Test from 10-2000Hz.
Solder temperature
Meet Table Ｃafter testing.
Resistance
to Soldering Heat
Pre-heating:150C +/-10 deg,60s to 90s
Meet Table A after testing.
260C+/-5 deg C
Immersion time 10s
17
18
ESD
Per AEC-Q200-002
Per J-STD-002
Meet Table Ｃ after testing.
ESD Rank: Meet Item 3. (Rating)
Solderability
Method b : Not Applicable
95% of the terminations is to be soldered.
19
Electrical
Characterization
Measured : Impedance
Per UL-94
No defects
20
21
Flammability
Board Flex
Not Applicable
Epoxy-PCB(1.6mm)
Deflection 2mm(min)
60s minimum holding tim
Per AEC-Q200-006
Meet TableＢafter testing.
22
30
Terminal Strength
No defects
Electrical
Transient
Conduction
Per ISO-7637-2
Not Applicable
8.Specification of Packaging
8-1.Appearance and Dimensions (8mm-wide paper tape)
2.0±0.05
4.0±0.1
+0.1
4.0±0.1
1.5
-0
1.05±0.1
BLM18_BH：1.1 max.
Direction of feed
BLM18_JH：0.85max.
(in mm)
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9129B-01
(1) Taping
P.5/10
Products shall be packaged in the cavity of the base tape of 8mm-wide,4mm-pitch continuously
and sealed by top tape and bottom tape.
(2) The sprocket holes are to the right as the tape is pulled toward the user.
(3) Spliced point:The base tape and top tape have no spliced point
(4) Cavity:There shall not be burr in the cavity.
(5) Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater,
and are not continuous. The specified quantity per reel are kept.
8-2.Tape Strength
(1)Pull Strength
Top tape
Bottom tape
5N min.
Top tape
165 to 180 degree
(2)Peeling off force of Top tape
F
0.1N to 0.6N (Minimum value is typical.)
*Speed of Peeling off:300mm/min
Bottom tape
Base tape
8-3.Taping Condition
(1)Standard quantity per reel
Quantity per 180mm reel: 4000 pcs. / reel
(2)There shall be leader-tape (top tape and empty tape ) and trailer- tape(empty tape) as follows.
(3)On paper tape, the top tape and the base tape shall not be adhered at the tip of the empty leader tape
for more than 5 pitch.
(4)Marking for reel
The following items shall be marked on a label and the label is stuck on the reel.
(Customer part number, MURATA part number, Inspection number(1) , RoHS marking (2) , Quantity, etc)
1) « Expression of Inspection No. »
□□ OOOO
(1)
(2)
(3)
(1) Factory Code
(2) Date
First digit
: Year / Last digit of year
Second digit
: Month / Jan. to Sep. 1 to 9, Oct. to Dec. O, N, D
Third, Fourth digit : Day
(3) Serial No.
2) « Expression of RoHS marking »
ROHS – Y (△)
(1) (2)
(1) RoHS regulation conformity parts.
(2) MURATA classification number
(5)Outside package
These reels shall be packed in the corrugated cardboard package and the following items shall be marked
on a label and the label is stuck on the box.
(Customer name, Purchasing order number, Customer part number, MURATA part number,
RoHS discrimination(2) ,Quantity, etc)
(6)Dimensions of reel and taping(leader-tape, trailer-tape)
Trailer
160 min.
Leader
2.0±0.5
Label
190 min.
210 min.
Top tape
Empty tape
13.0±0.2
60+1
-
0
Direction of feed
21.0±0.8
+1
-0
9.0
13.0±1.4
180 +0
-3
(in mm)
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9129B-01
P.6/10
8-4. Specification of Outer Case
Outer Case Dimensions
Label
Standard Reel Quantity in Outer Case
(Reel)
(mm)
D
H
W
H
186
186
93
5
D
Above Outer Case size is typical. It depends on a quantity of an order.
W
9.
Caution
9-1.Rating
Do not use products beyond the Operating Temperature Range and Rated Current.
9-2.Surge current
Excessive surge current (pulse current or rush current) than specified rated current applied to the product
may cause a critical failure, such as an open circuit, burnout caused by excessive temperature rise.
Please contact us in advance in case of applying the surge current.
9-3.Fail Safe
Be sure to provide an appropriate fail-safe function on your product to prevent from a second damage
that may be caused by the abnormal function or the failure of our products.
9-4.Limitation of Applications
Please contact us before using our products for the applications listed below which require especially high
reliability for the prevention of defects which might directly cause damage to the third party's life, body or property.
(1)Aircraft equipment
(6)Disaster prevention / crime prevention equipment
(7)Traffic signal equipment
(8)Transportation equipment (trains,ships,etc.)
(9)Data-processing equipment
(10)Applications of similar complexity and /or reliability requirements
to the applications listed in the above
(2)Aerospace equipment
(3)Undersea equipment
(4)Power plant control equipment
(5)Medical equipment
10. Notice
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
10-1.Land pattern designing
Standard land dimensions
< For BLM18 series >
Chip Ferrite Bead
Land pad thickness
and dimension d
18µm 35µm 70µm
Rated
Current
(A)
Type
a
b
c
c
d
0.7
1.2
2.4
6.4
0.7
0.7
1.2
0.7
0.7
0.7
~1.0
~1.5
~2.5
~4.0
Flow
2.2 to 2.6
Reflow
0.7
0.7
BLM18
Solder Resist
Pattern
a
b
1.8 to 2.0
3.3 1.65
(in mm)
The excessive heat by land pads may cause deterioration
at joint of products with substrate.
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9129B-01
P.7/10
10-2.Soldering Conditions
Products can be applied to reflow and flow soldering.
(1) Flux,Solder
Flux
Use rosin-based flux, but not highly acidic flux (with chlorine content exceeding 0.2(wt)%. )
Do not use water-soluble flux.
Solder
Use Sn-3.0Ag-0.5Cu solder
Standard thickness of solder paste : 100 µm to 200 m
(2) Soldering conditions
Pre-heating should be in such a way that the temperature difference between solder and ferrite surface is limited
to 150℃ max. Also cooling into solvent after soldering should be in such a way that the temperature difference
is limited to 100℃ max.
Insufficient pre-heating may cause cracks on the ferrite, resulting in the deterioration of product quality.
Standard soldering profile and the limit soldering profile is as follows.
The excessive limit soldering conditions may cause leaching of the electrode and / or resulting
in the deterioration of product quality.
(3)soldering profile
□Flow soldering profile
Temp.
(℃)
265℃±3℃
250℃
Limit Profile
150
Heating Time
Standard Profile
60s min.
Time.(s)
Standard Profile
150℃、60s min.
250℃、4～6s
2 times
Limit Profile
Pre-heating
Heating
265℃±3℃、5s max.
Cycle of flow
2 times
□Reflow soldering profile
Temp.
(℃)
260℃
230℃
245℃±3℃
220℃
Limit Profile
180
150
Standard Profile
30s～60s
60s max.
90s±30s
Time.(s)
Standard Profile
Limit Profile
Pre-heating
150～180°C 、90s±30s
Heating
above 220°C、30s～60s above 230°C、60s max.
Peak temperature
Cycle of reflow
245±3°C
260°C,10s
2 times
2 times
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9129B-01
P.8/10
10-3.Reworking with soldering iron
Pre-heating: 150°C, 1 min
Soldering iron output: 80W max.
Tip temperature: 350°C max.
Tip diameter:
φ3mm max.
Soldering time : 3(+1,-0) seconds.
Times : 2times max.
Note :Do not directly touch the products with the tip of the soldering iron in order to prevent the crack
on the ferrite material due to the thermal shock.
10-4.Solder Volume
Solder shall be used not to be exceeded as shown below.
Upper Limit
Recommendable
1/3T≦t≦T
t
(T:Chip thickness)
Accordingly increasing the solder volume, the mechanical stress to product is also increased.
Exceeding solder volume may cause the failure of mechanical or electrical performance.
10-5.Attention regarding P.C.B. bending
The following shall be considered when designing and laying out P.C.B.'s.
(1) P.C.B. shall be designed so that products are not subject to the mechanical stress for board warpage.
<Products direction>
a
b
Products shall be located in the sideways
direction (Length:ab) to the mechanical
stress.
Poor example
〈
〉
Good example
〈
〉
(2)Components location on P.C.B. separation.
It is effective to implement the following measures, to reduce stress in separating the board.
It is best to implement all of the following three measures; however, implement as many measures as possible
to reduce stress.
Contents of Measures
Stress Level
(1) Turn the mounting direction of the component parallel to the board separation surface.
(2) Add slits in the board separation part.
(3) Keep the mounting position of the component away from the board separation surface.
A
A
A
>
D *1
B
C
>
>
C
Perforation
B
D
A
Slit
*1 A > D is valid when stress is added vertically to the perforation as with Hand Separation.
If a Cutting Disc is used, stress will be diagonal to the PCB, therefore A > D is invalid.
(3) Mounting Components Near Screw Holes
When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during
the tightening of the screw. Mount the component in a position as far away from the screw holes as possible.
Recommended
Screw Hole
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9129B-01
P.9/10
10-6.Mounting density
Add special attention to radiating heat of products when mounting the inductor near the products with heating.
The excessive heat by other products may cause deterioration at joint of this product with substrate.
10-7. Operating Environment
Do not use this product under the following environmental conditions, on deterioration of the Insulation
Resistance of the Ferrite material and/or corrosion of Inner Electrode may result from the use.
(1) in the corrodible atmosphere (acidic gas, alkaline gas, chlorine, sulfur gas, organic gas and etc.)
(2) in the atmosphere where liquid such as organic solvent, may splash on the products.
(3) in the atmosphere where the temperature / humidity changes rapidly and it is easy to dew.
10-8. Resin coating
The impedance value may change and/or it may affect on the product's performance due to high cure-stress of
resin to be used for coating / molding products. So please pay your careful attention when you select resin. In prior to
use, please make the reliability evaluation with the product mounted in your application set.
10-9.Cleaning Conditions
Products shall be cleaned on the following conditions.
(1)Cleaning temperature shall be limited to 60°C max. (40°C max. for IPA.)
(2)Ultrasonic cleaning shall comply with the following conditions, avoiding the resonance phenomenon
at the mounted products and P.C.B.
Power:20W/ max. Frequency:28kHz to 40kHz Time:5 min max.
(3)Cleaner
1.Alternative cleaner
Isopropyl alcohol (IPA)
2.Aqueous agent
PINE ALPHA ST-100S
(4)There shall be no residual flux and residual cleaner after cleaning.
In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized water
in order to remove the cleaner.
(5)Other cleaning
Please contact us.
10-10. Handling of a substrate
After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the
substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to
the substrate.
Excessive mechanical stress may cause cracking in the product.
Bending
Twisting
10-11.Storage Conditions
(1)Storage period
Use the products within 6 months after delivered.
Solderability should be checked if this period is exceeded.
(2)Storage conditions
Products should be stored in the warehouse on the following conditions.
Temperature : -10°C to 40°C
Humidity
: 15% to 85% relative humidity
No rapid change on temperature and humidity
Don't keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization
of electrode, resulting in poor solderability.
Products should be stored on the palette for the prevention of the influence from humidity, dust and so on.
Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.
Products should be stored under the airtight packaged condition.
(3)Delivery
Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock.
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9129B-01
11. Note
P.10/10
(1)Please make sure that your product has been evaluated in view of your specifications with our product being
mounted to your product.
(2)You are requested not to use our product deviating from the agreed specifications.
(3) The contents of this reference specification are subject to change without advance notice. Please approve our product
specifications or transact the approval sheet for product specifications before ordering.
MURATA MFG.CO., LTD.
相关型号：
BLM18BD470SZ1D
Chip Ferrite Bead BLM18xxxxxxZ1D Murata Standard Reference Specification [AEC-Q200]
MURATA
©2020 ICPDF网 联系我们和版权申明