K1720ACM-2.0000MHZ [MTRONPTI]
Oscillator,;
MTRONPTI 
K1700A Series
5V Temperature Compensated Voltage Controlled Crystal Oscillators
! Applications: Phase Lock Loops
Clocking “Sync” to NTSC Video Standards;
Reference Signal; Signal Tracking; ATM
! 2.0 to 35.0 MHz Frequency Range
13,2 mm Max.
20,8 mm Max.
ax.
0AC
X
M
m
7
MHZ
K1
.000
TE CODE
CTI DA
7,49 m
20
o o
±10ppm Frequency Stability - (0 C to 70 C) K1710
!
o
o
!
±20ppm Frequency Stability - (-40 C to 85 C) K1720
! -40°C to 85°C Operating Temperature
! TTL/CMOS Compatible
PIN 1
! Meets Stratum IV Stability Requirements
! Hermetically Sealed Package
ELECTRICAL SPECIFICATIONS
Model
K1710AC
K1720ACM
Frequency Range (MHz)
Input Current (mA)
Frequency Control Function
Deviation (ppm)
2.0 to 35
< 30
(For Custom Deviation Range, Vc Range, etc. - Consult Factory)
Minimum (ppm)
Maximum
±60
±120
Linearity (%)
< 10
Modulation Bandwidth (±3dB)
Nominal Control Voltage (V)
Control Voltage Range (V)
Transfer Function
> 20KHz
2.5
0.5 to 4.5
Positive
> 50KΩ @ 10KHz
Input Impedance
Frequency Stability (ppm)
Overall
Inclusive of Calibration, Temperature, Voltage, Load, Aging
o
o
±10
-
-
0 C to 70 C
o
o
±20
-40 C to 85 C
Aging, 10 Years
±3.0
o
Temperature Range ( C)
o
o
o o
-40 C to +85 C
Operating
0 C to +70 C
o
o
Storage
Supply Voltage (V)
-40 C to +85 C
+5.0V ±5%
Symmetry CMOS/TTL
Start Up Time (ms)
Typical SSB Phase Noise (dBC/Hz)
Offset from Carrier
45/55 < 16MHz; 40/60 ≥ 16MHz
<10
10Hz
100Hz
1KHz
-65
-95
-120
-140
-150
10KHz
100KHz
PART NUMBERING GUIDE
K17X0AX - Specify Frequency
“Blank” = 0°C to 70°C Operating Temp.
“M” = -40°C to +85°C Operating Temp. K1720 Only
“1” = ±10ppm, 0°C to 70°C Operating Temp.
“2” = ±20ppm, -40°C to +85°C Operating Temp.
2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585
800-888-1499 or www.champtech.com
1
K1700A Series
5V Temperature Compensated Voltage Controlled Crystal Oscillators
PIN
FUNCTION
1
7
8
Voltage Control
Gnd/ & Case Gnd
Output
+ V
14
CC
SHIPPING TUBE CROSS SECTION
TEST CIRCUIT DIAGRAM
OUTPUT WAVEFORM
MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS
TEST METHODS
REFERENCE PROCEDURES
DESCRIPTION
-55°C to +125°C; Air-to-Air; 100 cycles; 10
Temperature Cycle
MIL-STD-833, Mtd 1010, Cond. B
min. dwell
Mechanical Shock
Vibration
Humidity Steady State
Thermal Shock
Electrostatic Discharge
Solderability
MIL-STD-883, Mtd 2002, Cond. B
MIL-STD 883, Mtd 2007, Cond. B
MIL-STD-202, Mtd 103
MIL-STD-883, Mtd 1011.7 Cond. B
MIL-STD-883, Mtd 3015 Class II
MIL-STD-883, Mtd 2022.2
1500 g’s
20-2000 Hz; 0.06 inch; 15g’s; 3 planes
40°C; 90%-95% R.H.; 56 days
100°C to 0°C; Water-to-Water; 15 cycles
2 KV to 4 KV Threshold
Solder dip; Meniscograph Criteria
Mass spectro. 2 x 10-8 atmos. CC/sec He
260°C; 10 seconds: 1 inch/sec.
Hermeticity
MIL-STD-883, Mtd 1014.8, Cond. A1
Resistance to Soldering MIL-STD-202, Mtd 210A, Cond. C
Lead Integrity
MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress
Marking Permanence
Life Test
MIL-STD-883, Mtd 2015.8
MIL-STD-883, Mtd 1005.6
Resistance to solvents
125°C, powered, 1000 hours minimum
2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585
800-888-1499 or www.champtech.com
2
相关型号：
©2020 ICPDF网 联系我们和版权申明