K1570A_07 [MTRONPTI]
5V Voltage Controlled Crystal Oscillators; 5V电压控制晶体振荡器
| 型号： | K1570A_07 |
| 厂家： | 
MTRONPTI |
| 描述： | 5V Voltage Controlled Crystal Oscillators |
| 文件： | 总2页 (文件大小：444K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
K1570A Series
5V Voltage Controlled Crystal Oscillators
This product is not recommended for new designs. Please refer to the MV product series.
Applications: Phase-Locked Loops (PLL’s); Clock
Recovery; Reference Signal Tracking;
13,08 mm Max.
20,7 mm Max.
Synthesizers; Frequency Modulation/Demodulation
ax.
M
m
K1570A
46.000 MHZ
CTI DA
m
TE CODE
7,6
14-pin DIL Package
1.0 to 52.0 MHz Frequency Range
0.5V to 4.5V Control Voltage
±25ppm Stability
PIN 1
-40°C to 85°C Operating Temperature
ELECTRICAL SPECIFICATIONS
Model
K1570A
1 to 52
< 26
Frequency Range (MHz)
Input Current (mA)
Frequency Control Function
Deviation (ppm)
(For Custom Deviation Range, Vc Range, etc. - Consult Factory)
Minimum
Maximum
±100
±150
Linearity (%)
< 10
Modulation Bandwidth (±3dB)
Nominal Control Voltage (V)
Control Voltage Range (V)
Transfer Function
Input Impedance
> 20KHz
2.5
0.5 to 4.5
Positive
> 50KΩ @ 10KHz
Frequency Stability (ppm)
Overall
Inclusive of Calibration, Temperature, Voltage, Load and Aging
o
o
±25
±50
0 C to +70 C
o
o
-40 C to +85 C
o
Temperature Range ( C)
o
o
Operating
-40 C to +85 C
o
o
Storage
Supply Voltage (V)
Symmetry (%) CMOS/TTL
Start Up Time (ms)
-55 C to +125 C
+5.0V ±5%
40/60
<10
Typical SSB Phase Noise (dBC/Hz)
Offset from Carrier
10Hz
100Hz
1KHz
10KHz
100KHz
-65
-95
-120
-140
-150
PART NUMBERING GUIDE
K1570A XX - Specify Frequency
“Blank” = 0°C to 70°C Operating Temp.
“M” = -40°C to +85°C Operating Temp.
o
o
“A” = ±25ppm (0 C to 70 C Op. Temp. Only
“B” = ±50ppm
2553 N. Edgington Street, Franklin Park, IL 60131 y Phone: 847.451.1000 y Fax: 847.451.7585
800-888-1499 or www.champtech.com
Revision: 03-09-07
1
K1570A Series
Voltage Controlled Crystal Oscillators
This product is not recommended for new designs. Please refer to the MV product series.
PIN
FUNCTION
1
7
8
Voltage Control
Gnd/ & Case Gnd
Output
+ V
14
CC
SHIPPING TUBE CROSS SECTION
TEST CIRCUIT DIAGRAM
OUTPUT WAVEFORM
MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS
TEST METHODS
REFERENCE PROCEDURES
DESCRIPTION
-55°C to +125°C; Air-to-Air; 100 cycles; 10
Temperature Cycle
MIL-STD-833, Mtd 1010, Cond. B
min. dwell
Mechanical Shock
Vibration
Humidity Steady State
Thermal Shock
Electrostatic Discharge
Solderability
MIL-STD-883, Mtd 2002, Cond. B
MIL-STD 883, Mtd 2007, Cond. B
MIL-STD-202, Mtd 103
MIL-STD-883, Mtd 1011.7 Cond. B
MIL-STD-883, Mtd 3015 Class II
MIL-STD-883, Mtd 2022.2
1500 g’s
20-2000 Hz; 0.06 inch; 15g’s; 3 planes
40°C; 90%-95% R.H.; 56 days
100°C to 0°C; Water-to-Water; 15 cycles
2 KV to 4 KV Threshold
Solder dip; Meniscograph Criteria
Mass spectro. 2 x 10-8 atmos. CC/sec He
240°C; 10 seconds: 1 inch/sec.
Hermeticity
MIL-STD-883, Mtd 1014.8, Cond. A1
Resistance to Soldering MIL-STD-202, Mtd 210D, Cond. C
Lead Integrity
MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress
Marking Permanence
Life Test
MIL-STD-883, Mtd 2015.8
MIL-STD-883, Mtd 1005.6
Resistance to solvents
125°C, powered, 1000 hours minimum
2553 N. Edgington Street, Franklin Park, IL 60131 y Phone: 847.451.1000 y Fax: 847.451.7585
800-888-1499 or www.champtech.com
Revision: 03-09-07
2
相关型号：
©2020 ICPDF网 联系我们和版权申明