R7G4HEIP-6-DC16B-R/Q [MSYSTEM]
Remote I/O R7G4H Series EtherNet/IP I/O MODULE;型号: | R7G4HEIP-6-DC16B-R/Q |
厂家: | M-SYSTEM |
描述: | Remote I/O R7G4H Series EtherNet/IP I/O MODULE |
文件: | 总5页 (文件大小:194K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: R7G4HEIP-6-DC16B
/C02: Polyurethane coating
/C03: Rubber coating
Remote I/O R7G4H Series
EtherNet/IP I/O MODULE
(PNP transistor output, 16 points, screw terminal block)
RELATED PRODUCTS
• PC configurator software (model: R7CFG)
Functions & Features
• EDS file
• 16 points PNP transistor output module for EtherNet/IP
• Supports DLR (Device Level Ring) to form a ring topology
The EDS files and configurator software are downloadable at
M-System’s web site.
For connecting to PC, use commercially available Mini-B
type USB cable. (provided by user)
130 (5.12)
GENERAL SPECIFICATIONS
Connection
EtherNet/IP: RJ-45 Moduler Jack
Power input, output: M3 separable screw terminal (torque
0.5 N·m)
55 (2.17)
Solderless terminal: Refer to the drawing at the end of the
section.
55 (2.17)
(mm)
Recommended manufacturer: Japan Solderless Terminal
MFG.Co.Ltd, Nichifu Co.,ltd
MODEL: R7G4HEIP-6-DC16B-R[1]
Applicable wire size: 0.25 to 1.65 mm
2
(AWG 22 to 16)
Screw terminal: Nickel-plated steel
Housing material: Flame-resistant resin (gray)
Isolation: Output to EtherNet/IP or FE to power
Output at the loss of communication: Configurable via
R7CFG
ORDERING INFORMATION
• Code number: R7G4HEIP-6-DC16B-R[1]
Specify a code from below for [1].
(e.g. R7G4HEIP-6-DC16B-R/Q)
Status indicator LED: PWR, RUN
• Specify the specification for option code /Q
(e.g. /C01)
(Refer to the instruction manual)
Discrete output status indicator LED: Green LED turns on
with output ON
TERMINAL BLOCK
■Recommended solderless terminal
6: Screw terminal block for power supply
RJ-45 Modular jack for communication
Screw terminal block for I/O
3.3 (.13) max
mm (inch)
I/O TYPE
DC16B: PNP transistor output, 16 points
EtherNet/IP COMMUNICATION
Communication Standard: IEEE 802.3u
POWER INPUT
DC power
Transmission: 10BASE-T, 100BASE-TX
R: 24 V DC
Baud rate: 10/100 Mbps (Auto Negotiation function)
Protocol: EtherNet/IP
(Operational voltage range: ±10 %; ripple 10 %p-p max.)
Max. number of socket connections: 3
Connection type: Exclusive owner / Listen only / Input only
Transmission media: 10BASE-T (STP, Category 5), 100BASE-
TX (STP, Category 5e)
[1] OPTIONS
blank: none
/Q: With options (specify the specification)
Network topology: Line, star and ring
Max. length of fieldbus segment: 100 meters
IP address: 192.168.0.250 (factory setting);
Only host address in IP address is configurable via rotary
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
R7G4HEIP-6-DC16B SPECIFICATIONS
ES-8004-C Rev.1 Page 1/5
http://www.m-system.co.jp/
MODEL: R7G4HEIP-6-DC16B
switches, the other items via PC configurator software
(model: R7CFG).
PC CONFIGURATOR
The following parameters can be set with using PC
Configurator Software (model: R7CFG)
Refer to the users manual for the R7CFG for detailed
operation of the software program.
■ CHANNEL BATCH SETTING
DLR supported
Port No.: 2222, 44818
I/O data size: One (1) word
Status indicator LEDs: MS, NS (Refer to the instruction
manual for details)
DEFAULT
PARAMETER
SETTING RANGE
SETTING
Hold
Output Hold / Clear Hold / Clear
OUTPUT SPECIFICATIONS
Common: Positive common (PNP) per 16 points
Maximum outputs applicable at once: No limit (at 24 V DC)
Rated load voltage: 24 V DC ±10 %, ripple 5 %p-p max.
Rated output current: 0.1 A per point, 1.6 A per common
Residual voltage: ≤ 1.2 V
■ EtherNet SETTING
DEFAULT
SETTING
PARAMETER
SETTING RANGE
IP Address
0.0.0.0 - 255.255.255.255
0.0.0.0 - 255.255.255.255
192.168.0.250
255.255.255.0
192.168.0.1
3.0 (sec.)
Subnet Mask
Default Gateway 0.0.0.0 - 255.255.255.255
Leakage current: ≤ 0.1 mA
Time Out
0.0 - 3276.7 (sec.)
DHCP / CONFIG
ON delay: ≤ 0.2 msec.
Use IP Address
CONFIG
OFF delay: ≤ 0.5 msec.
Overload current protection function: Limits the current
value when overcurrent is detected
Overheat protection function: Turns OFF the outputs when
overheat is detected
(When driving an inductive load, connect a diode in parallel
with the load.)
INSTALLATION
Current consumption
•DC: Approx. 50 mA
Operating temperature: -10 to +55°C (14 to 131°F)
Storage temperature: -20 to +65°C (-4 to +149°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Surface or DIN rail (35 mm rail)
Weight: 200 g (0.44 lb)
PERFORMANCE
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute
(output to EtherNet/IP or FE to power)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EN 50581
R7G4HEIP-6-DC16B SPECIFICATIONS
ES-8004-C Rev.1 Page 2/5
http://www.m-system.co.jp/
MODEL: R7G4HEIP-6-DC16B
EXTERNAL VIEW
IP Address Setting
Rotary SW
Discrete Output Status Indicator LED
PC Configurator Jack
Status Indicator LED
RJ-45 Modular Jack
SA1
×10
SA2
×1
LNK1
LNK2
PWR NS LNK2
MS LNK1
CNFG.
4
5
6
3
7
10 11 12 13 14 15 16 17 18
1
2
9
1
2
3
4
5
6
7
8
Power Supply Terminals
Output Terminals
TERMINAL ASSIGNMENTS
■OUTPUT TERMINAL ASSIGNMENT
10
V+
11
Y1
12
Y3
13
Y5
14
Y7
15
16
17
18
Y9 Y11 Y13 Y15
1
2
3
4
5
6
7
8
9
V
-
Y0
Y2
Y4
Y6
Y8 Y10 Y12 Y14
NO. ID
FUNCTION NO. ID
FUNCTION
1
2
3
4
5
6
7
8
9
V
-
0V
10
11
12
13
14
15
V+ 24V DC (Out. Common)
Y1 Output 1
Y0 Output 0
Y2 Output 2
Y4 Output 4
Y6 Output 6
Y8 Output 8
Y10 Output 10
Y12 Output 12
Y14 Output 14
Y3 Output 3
Y5 Output 5
Y7 Output 7
Y9 Output 9
16 Y11 Output 11
17 Y13 Output 13
18 Y15 Output 15
■POWER SUPPLY TERMINAL ASSIGNMENT
4 5
NC NC
6
+
7
24V 0V
1
2
3
NC NC FE
1. NC
2. NC
3. FE
4. NC
5. NC
6. +24V
7. 0V
-
-
Functional earth
-
-
Power supply (24V DC)
Power supply (0V)
R7G4HEIP-6-DC16B SPECIFICATIONS
ES-8004-C Rev.1 Page 3/5
http://www.m-system.co.jp/
MODEL: R7G4HEIP-6-DC16B
I/O DATA DESCRIPTIONS
■ DISCRETE OUTPUT
15
0
Output 0
Output 1
Output 2
Output 3
Output 7
Output 8
Output 15
0: OFF 1: ON
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm
154 (6.06)
140 (5.51)
55 (2.17)
[(4) 0.16]
130 (5.12)
4
5
6
7
10 11 12 13 14 15 16 17 18
1
2
3
9
1
2
3
4
5
6
7
8
DIN RAIL
35mm wide
2 – 4.3 dia. 4 deep.
6
6
7–M3 SCREW
18–M3 SCREW
TERMINALS for Output
TERMINALS for
POWER SUPPLY
MOUNTING REQUIREMENTS unit: mm (inch)
140 (5.51)
2 – M4
R7G4HEIP-6-DC16B SPECIFICATIONS
ES-8004-C Rev.1 Page 4/5
http://www.m-system.co.jp/
MODEL: R7G4HEIP-6-DC16B
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Note: In order to improve EMC performance, bond the FE terminal to ground.
Caution: FE terminal is NOT a protective conductor terminal.
■ Output Circuit
Comm. Circuit
Output Circuit
1
*
*
RJ-45 Modular Jack
1
2
EtherNet/IP
V–
10 V+
Control
Circuit
1
Y0
RJ-45 Modular Jack
EtherNet/IP
3
Y2
2
Y0
3
6
7
1
2
4
5
FE
24V DC
0V
4
Y4
5
Y6
Control
Circuit
6
Y8
NC
7
Y10
Y12
Y14
V+
NC
8
18 Y15
V–
NC
9
1
NC
10
11
12
13
14
15
16
17
18
Y1
■ Output Connection Examples
Y3
+
−
V+ 10
Y5
V–
Y0
1
2
Y7
Y9
Y11
Y13
Y15
Y15 18
*1. The network cable can be connected to either one.
Specifications are subject to change without notice.
R7G4HEIP-6-DC16B SPECIFICATIONS
ES-8004-C Rev.1 Page 5/5
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明