R3-RS8W/CE [MSYSTEM]
Remote I/O R3 Series RTD INPUT MODULE;型号: | R3-RS8W/CE |
厂家: | M-SYSTEM |
描述: | Remote I/O R3 Series RTD INPUT MODULE 输入元件 |
文件: | 总5页 (文件大小:140K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: R3-RS8
Remote I/O R3 Series
GENERAL SPECIFICATIONS
Connection
Internal bus: Via the Installation Base (model: R3-BSx)
Input: M3 separable screw terminal (torque 0.5 N·m)
Internal power: Via the Installation Base (model: R3-BSx)
Screw terminal: Nickel-plated steel
RTD INPUT MODULE
(8 points, isolated)
27.5 [1.08]
Isolation: Input 1 to input 2 to input 3 to input 4 to input 5 to
input 6 to input 7 to input 8 to internal bus or internal power
Sensor type: Selectable with the side DIP SW
(Independent types selectable per group of 4 channels.)
Temperature unit: °C, °F or absolute temperature selectable
with the side DIP SW
130
[5.12]
Conversion rate: Selectable with the side DIP SW
Burnout detection: Upscale or downscale selectable with the
side DIP SW
109
[4.29]
mm [inch]
Linearization: Standard
RUN indicator: Bi-color (red/green) LED;
Red when the bus A operates normally;
MODEL: R3-RS8[1][2]
Green when the bus B operates normally;
Amber when both buses operate normally.
ERR indicator: Bi-color (red/green) LED;
ORDERING INFORMATION
• Code number: R3-RS8[1][2]
Specify a code from below for each of [1] and [2].
(e.g. R3-RS8W/CE/Q)
Red with burnout; Green in normal operating conditions.
• Specify the specification for option code /Q
(e.g. /C01/SET)
INPUT SPECIFICATIONS
Maximum leadwire resistance: 100 Ω per wire
Sensing current: ≤ 1 mA
NO. OF CHANNELS
Temperature range
8: 8
°C
RTD
USABLE RANGE CONFORMANCE RANGE
Pt 100 (JIS ’97, IEC)
Pt 100 (JIS ’89)
-240 to +900
-240 to +900
-236 to +560
-200 to +850
-200 to +660
-200 to +510
[1] COMMUNICATION MODE
S: Single
JPt 100 (JIS ’89)
W: Dual
Pt 50Ω (JIS ’81)
Ni 100
-236 to +700
-100 to +252
-212 to +312
-100 to +200
-200 to +649
-80 to +250
-50 to +250
-50 to +150
Cu 10 @25°C
Cu 50
[2] OPTIONS (multiple selections)
Standards & Approvals
blank: Without CE
°F
USABLE RANGE CONFORMANCE RANGE
RTD
/CE: CE marking
Pt 100 (JIS ’97, IEC)
Pt 100 (JIS ’89)
-400 to +1652
-400 to +1652
-393 to +1040
-328 to +1562
-328 to +1220
-328 to +950
Other Options
JPt 100 (JIS ’89)
blank: none
Pt 50Ω (JIS ’81)
Ni 100
-393 to +1292
-148 to +486
-350 to +594
-148 to +392
-328 to +1200
-112 to +482
-58 to +482
-58 to +302
/Q: Option other than the above (specify the specification)
Cu 10 @25°C
Cu 50
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
Max. (upscale) or min. (downscale) value of the usable range when
a burnout is detected.
/C02: Polyurethane coating
/C03: Rubber coating
EX-FACTORY SETTING
/SET: Preset according to the Ordering Information Sheet
(No. ESU-8365)
R3-RS8 SPECIFICATIONS
ES-8365 Rev.10 Page 1/5
https://www.m-system.co.jp/
MODEL: R3-RS8
INSTALLATION
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Installation Base (model: R3-BSx)
Weight: 250 g (0.55 lb)
PERFORMANCE
Conversion accuracy: ±1.0°C (±1.8°F) except ±3.0°C
(±5.4°F) for Cu 10 @ 25°C
Conversion rate: 250 msec. or 1 sec. selectable
Data range
°C, absolute temperature: Engineering unit value × 10
(integer)
°F: Engineering unit value (integer)
Data allocation: 8
Current consumption: 100 mA
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Burnout response time: ≤ 2 sec.
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1000 V AC @ 1 minute (input 1 to input
2 to input 3 to input 4 to input 5 to input 6 to input 7 to
input 8 to internal bus or internal power)
2000 V AC @ 1 minute (power input to FG; isolated on the
power supply module)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
R3-RS8 SPECIFICATIONS
ES-8365 Rev.10 Page 2/5
https://www.m-system.co.jp/
MODEL: R3-RS8
EXTERNAL VIEW
■ SIDE VIEW
■ FRONT VIEW
RUN LED
ERR LED
1
2
15
16
17
18
19
20
21
22
23
24
25
26
27
28
3
4
Functions
RTD
5
SW1
SW2
SW3
6
Burnout
7
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
Input 1-4 (SW1)
or
Input 5-8 (SW2)
Temp.
Unit
Conv.
8
9
Rate
10
11
12
13
14
ON
ON
ON
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]
27.5 [1.08]
109 [4.29]
POSITIONING
GUIDE
1
15
2
16
3
17
4
18
5
19
6
28–M3
SCREW
20
7
21
8
22
9
23
10
24
11
25
12
26
13
27
14
28
TERMINAL
COVER
R3-RS8 SPECIFICATIONS
ES-8365 Rev.10 Page 3/5
https://www.m-system.co.jp/
MODEL: R3-RS8
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
RUN LED ERR LED DIP SW
Input Circuit
RTD
INTERNAL BUS A
Communication
Circuit
A
1
INTERNAL BUS B*
INPUT 1
B
B
2
3
Control
Circuit
Input Circuit
Input Circuit
Input Circuit
Input Circuit
Input Circuit
Input Circuit
Input Circuit
RTD
RTD
RTD
RTD
RTD
RTD
RTD
INTERNAL POWER
A
B
B
4
5
6
INPUT 2
INPUT 3
INPUT 4
INPUT 5
INPUT 6
INPUT 7
INPUT 8
13
14
27
28
A
B
B
7
8
9
A
B
B
10
11
12
A
B
B
15
16
17
A
B
B
18
19
20
A
B
B
21
22
23
A
B
B
24
25
26
*For dual redundant communication.
• Unused Input Channels
Close scross the unused input terminals with a resistor as shown below and set the DIP switch for an RTD.
INPUT 1
1
INPUT 2
4
INPUT 3
7
INPUT 4
10
2
3
5
6
8
9
11
12
INPUT 5
15
INPUT 6
18
INPUT 7
21
INPUT 8
24
16
17
19
20
22
23
25
26
The resistance value must match the RTD type (100Ω for Pt 100, 50Ω for Pt 50Ω).
Unused channels left open are equal to the burnout, which turns the red ERR LED on and sets a burnout flag
at the PLC or the host device.
Unused channels can be speci"ed and set so on the PC Con"gurator Software (model: R3CON) without needing
to connect resistors at the "eld terminals.
R3-RS8 SPECIFICATIONS
ES-8365 Rev.10 Page 4/5
https://www.m-system.co.jp/
MODEL: R3-RS8
Specifications are subject to change without notice.
R3-RS8 SPECIFICATIONS
ES-8365 Rev.10 Page 5/5
https://www.m-system.co.jp/
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明