M6NXF3-S2V2-R/Q [MSYSTEM]
Screw Terminal Ultra-Slim Signal Conditioners M6N Series;型号: | M6NXF3-S2V2-R/Q |
厂家: | M-SYSTEM |
描述: | Screw Terminal Ultra-Slim Signal Conditioners M6N Series |
文件: | 总5页 (文件大小:149K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: M6NXF3
(Configurator software is used to change input over the
described range of the selected suffix code.
Screw Terminal Ultra-Slim Signal Conditioners M6N Series
For changing between suffix codes, set the Input Range
Selector on the side of unit before software adjustment.)
HOLD FUNCTION MODULE
(PC programmable)
Functions & Features
[2] OUTPUT
Current
• Track/Hold or Peak hold function’s selection available
• 7.5-mm wide ultra-slim design with DC current signal
input
Z1: Range 0 – 20 mA DC
Voltage
• Low profile allows the M6N module to be mounted in a
120-mm deep panel
V2: Range -10 – +10 V DC
V3: Range -5 – +5 V DC
• PC programmable
(Configurator software is used to change output over the
described range of the selected suffix code.
For changing between suffix codes, set the Output Range
Selector on the side of unit before software adjustment.)
• High-density mounting available
• Power and status indicator LEDs
Typical Applications
• Monitoring peak power consumption
• Monitoring the highest or lowest temperature
• Capturing signals from a composite analyzer performing
on each sample in turn
POWER INPUT
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
7.5 (.30)
[3] OPTIONS
blank: none
/Q: With options (specify the specification)
102
(4.02)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
102
(4.02)
/C02: Polyurethane coating
mm (inch)
FUNCTIONS
PC Configurator Software is used to change function type.
• Track/Hold
MODEL: M6NXF3–[1][2]–R[3]
• Peak hold
Peak hold
ORDERING INFORMATION
• Code number: M6NXF3-[1][2]-R[3]
Specify a code from below for each [1] through [3].
(e.g. M6NXF3-Z1Z1-R/Q)
Valley hold
Peak-to-peak hold (Peak hold-Valley hold)
Factory default setting
Control/Hold: Track/Hold
Control/Control Logic: Hold at open
• Input range (e.g. 4 – 20 mA DC)
• Output range (e.g. 4 – 20 mA DC)
• Specify the specification for option code /Q
(e.g. /C01)
RELATED PRODUCTS
• PC configurator software (model: M6CFG)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
[1] INPUT
Current
Z1: Range 0 – 50 mA DC (Input resistance 24.9 Ω)
Voltage
S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.)
S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.)
M6NXF3 SPECIFICATIONS
ES-7920 Rev.4 Page 1/5
http://www.m-system.co.jp/
MODEL: M6NXF3
• Control
GENERAL SPECIFICATIONS
Connection
Contact rating: 3 V @1 mA
Detection levels:
Input and output: M3 screw terminal (torque 0.5 N·m)
Power input: Via the Installation Base (model: M6NBS)
or M3 screw terminal (torque 0.5 N·m)
Recommended solderless terminal: Max. 5.8 mm (0.23”)
wide; Ones with insulation sleeve do not fit.
≤ 0.6 kΩ / 0.5 V at close
≥ 15 kΩ / 2.5 V at open
OUTPUT SPECIFICATIONS
■ DC Current
Applicable wire size: 0.2 – 2.5 mm
2
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Output range: 0 – 20 mA DC
Conformance range: 0 – 20.4 mA DC
Minimum span: 1 mA
Overrange output: -2 – +102 %
(Negative current output is not available.)
Offset: Lower range can be any specific value within the
output range provided that the minimum span is
maintained.
Zero adjustment: -2 to +2 % (PC programming)
Span adjustment: 98 to 102 % (PC programming)
Power LED: Green light turns on when the power is supplied.
Status indicator LED: Orange LED; Blinking patterns indicate
different operating status of the transmitter.
Programming: Downloaded from PC; input type and range,
output type and range, zero and span, function type, control
input logic, user’s linearization table (max. 101 points,
specified within -2 to +102% for both input and output), etc.
For detailed information, refer to the users manual for the
PC configurator.
Load resistance: Output drive 11 V max.
(e.g. 4 – 20 mA: 550 Ω [11 V ÷ 20 mA])
If not specified, the output range is 4 – 20 mA DC.
■ DC Voltage
Code V2 (wide spans)
Output range: -10 – +10 V DC
Conformance range: -10.4 – +10.4 V DC
Minimum span: 1 V
Code V3 (narrow spans)
Configurator connection: 2.5 dia. miniature jack;
RS-232-C level
Output range: -5 – +5 V DC
Conformance range: -5.2 – +5.2 V DC
Minimum span: 0.5 V
■Recommended solderless terminal (unit: mm (inch))
Offset: Lower range can be any specific value within the
output range provided that the minimum span is
maintained.
5.5 max.
(.22)
4 min.
(.16)
3.2 (.13) dia.
Load resistance: Output drive 1 mA max.
(e.g. 1 – 5 V: 5000 Ω [5 V ÷ 1 mA])
If not specified, the output range is shown below.
V2: 0 – 10 V DC
V3: 1 – 5 V DC
INPUT SPECIFICATIONS
■ DC Current: Input resistor incoporated
(If not specified, the input range is 4 – 20 mA DC.)
Input range: 0 – 50 mA DC
INSTALLATION
Power consumption: Approx. 0.5 W
Minimum span: 2 mA
Operating temperature: -20 to +55°C (-4 to +131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Installation Base (model: M6NBS) or DIN rail
Weight: 65 g (2.3 oz)
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
■ DC Voltage
•Code S1 (narrow spans)
Input range: -1000 – +1000 mV DC
Minimum span: 100 mV
PERFORMANCE in percentage of span
Overall accuracy: Input accuracy + output accuracy
Inversely proportional to the span.
•Code S2 (wide spans)
Input range: -10 – +10 V DC
See CALCULATION EXAMPLES OF OVERALL ACURACY.
• Input accuracy: (% of max. input range)
-1000 – +1000 mV : ±0.01 %
Minimum span: 1 V
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
If not specified, the input range is shown below.
S1: 0 – 100 mV DC
-10 – +10 V : ±0.01 %
0 – 50 mA : ±0.02 %
• Output accuracy: ±0.04 % of max. output range
S2: 1 – 5 V DC
M6NXF3 SPECIFICATIONS
ES-7920 Rev.4 Page 2/5
http://www.m-system.co.jp/
MODEL: M6NXF3
Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span
Response time: ≤ 0.5 sec. (0 – 90 %)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
CALCULATION EXAMPLES OF OVERALL ACCURACY
[Example] Input Type -10 – +10 V, Input Range 1 – 5 V,
Output Type -5 – +5 V, Output Range 1 – 5 V
• Input accuracy = Max. Input Range (20 V) ÷ Span (4 V) ×
0.01 % = 0.05 %
• Output accuracy = Max. Output Range (10 V) ÷ Span (4 V)
× 0.04 % = 0.1 %
Accuracy= ±0.15 %
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EN 50581
EXTERNAL VIEW
FRONT VIEW (with the cover open)
SIDE VIEW
Output Range Selectors
5
6
7
8
Power LED
Status Indicator LED
Configurator Jack
Input Range Selectors
1
2
3
4
The DIP switch setting is required to select input and output
types before setting a precise range using PC Configurator
Software (model: M6CFG).
Refer to the instruction manual for detailed procedures.
M6NXF3 SPECIFICATIONS
ES-7920 Rev.4 Page 3/5
http://www.m-system.co.jp/
MODEL: M6NXF3
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
SCREWDRIVER
INSERTION ANGLE
: approx. 55°
*
WIRE INSERTION ANGLE
: approx. 35°
8–M3
SCREW TERMINAL
DIN RAIL HOOK
5
6
7
8
DIN RAIL
35mm wide
1
2
3
4
[1 (.04)]
SCREWDRIVER
INSERTION ANGLE
: approx. 40°
7.5 (.30)
102 (4.02)
*Screwdriver stem diameter: 6 mm (.24”) or less
• When mounting, no extra space is needed between units.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
STATUS
IND. LED
DIP SW
Isolation
Digital
Computation
Output
Driver
5
6
+
–
OUTPUT
POWER
+
–
Low Drift
Amplifier
1
2
24.9 Ω
+3 V
INPUT
POWER LED
+
–
7
8
3 kΩ
3
4
CONTROL
POWER
CONFIGURATOR
JACK
M6NXF3 SPECIFICATIONS
ES-7920 Rev.4 Page 4/5
http://www.m-system.co.jp/
MODEL: M6NXF3
FUNCTIONS
■ CONTROL LOGIC
The control input can be chosen either hold at open or hold at close by using the PC Configurator Software.
For detailed information on the PC Configuration, refer to the M6CFG users manual.
■ TRACK/HOLD
When the control input is TRACK, the output follows proportionally to the input.
When the control input turns to HOLD, the output at the point of command is held indefinitely.
■ PEAK HOLD
• Peak hold
When the control input is TRACK, the output follows proportionally to the input.
When the control input is HOLD, the output is held at the maximum input value.
When the maximum input value is updated, the output changes to that value.
• Valley hold
When the control input is TRACK, the output follows proportionally to the input.
When the control input is HOLD, the output is held at the minimum input value.
When the minimum input value is updated, the output changes to that value.
• Peak-to-peak hold
When the control input is TRACK, the output follows proportionally to the input.
When the control input is HOLD, the output is held at the maximum peak-to-peak input value (max. value – min. value).
For example, the output is 20% if the maximum input value is 60% and the minimum input value is 40%.
When the maximum peak-to-peak input value is updated, the output changes to that value.
Specifications are subject to change without notice.
M6NXF3 SPECIFICATIONS
ES-7920 Rev.4 Page 5/5
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明