M6DXAS [MSYSTEM]
Euro Terminal Ultra-Slim Signal Conditioners M6D Series;型号: | M6DXAS |
厂家: | M-SYSTEM |
描述: | Euro Terminal Ultra-Slim Signal Conditioners M6D Series |
文件: | 总4页 (文件大小:148K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: M6DXAS
Euro Terminal Ultra-Slim Signal Conditioners M6D Series
POWER INPUT
DC Power
R: 24 V DC
DC ALARM
(PC programmable)
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
Functions & Features
• 5.9-mm wide ultra-slim design
• Low profile allows the M6D module mounted in a 120-mm
deep panel
[2] OPTIONS
blank: none
/Q: With options (specify the specification)
• PC programmable
• High-density mounting
• Power and status indicator LEDs
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
5.9 (.23)
/C02: Polyurethane coating
EX-FACTORY SETTING
/SET: Preset according to the Ordering Information Sheet
(No. ESU-7828)
94
(3.70)
RELATED PRODUCTS
• PC configurator software (model: M6CFG)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
102
(4.02)
mm (inch)
MODEL: M6DXAS–[1]–R[2]
GENERAL SPECIFICATIONS
Connection
ORDERING INFORMATION
• Code number: M6DXAS-[1]-R[2]
Specify a code from below for each [1] and [2].
(e.g. M6DXAS-Z1-R/Q)
Input and output: Euro terminal (torque 0.3 N·m)
Power input: Via the Installation Base (model: M6DBS)
or Euro terminal (torque 0.3 N·m)
Applicable wire size: 0.2 to 2.5 mm , stripped length 8 mm
2
• Input range (e.g. 4 – 20 mA DC)
• Specify the specification for option code /Q
(e.g. /C01/SET)
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Power LED: Green light turns on when the power is supplied.
Status indicator LED: Orange LED; Blinking patterns indicate
different operating status of the transmitter.
Alarm monitor LED: Red LED turns on when the alarm is
tripped.
[1] INPUT
Current
Z1: Range 0 – 50 mA DC (Input resistance 24.9 Ω)
Voltage
Programming: Downloaded from PC
Input type and range
S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.)
S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.)
(Configurator software is used to change input over the
described range of the selected suffix code.
For changing between suffix codes, set the Input Range
Selector on the side of unit before software adjustment.)
Input fine adjustments
Alarm setpoint (input %)
Trip action (High or Low)
Relay coil (energized or de-energized)
Power ON delay time (0 to 999 sec.)
Alarm ON delay time (0 to 999 sec.)
Hysteresis (deadband) (input %)
OUTPUT
Relay; SPDT or transfer contact
Alarm test, and others
For detailed information, refer to the users manual for the
PC configurator.
M6DXAS SPECIFICATIONS
ES-7828 Rev.8 Page 1/4
http://www.m-system.co.jp/
MODEL: M6DXAS
Configurator connection: 2.5 dia. miniature jack;
RS-232-C level
INSTALLATION
Power consumption: Approx. 0.5 W
Factory default setting
Operating temperature: -20 to +55°C (-4 to +131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Installation Base (model: M6DBS) or DIN rail
Weight: 65 g (2.3 oz)
Alarm setpoint: 80 %
Trip action: High
Relay coil at alarm: Energized
Power ON delay time: 5 sec.
Alarm ON delay time: 0 sec.
Hysteresis (deadband) : 1.0 %
PERFORMANCE in percentage of span
Setpoint accuracy (trip point accuracy) : ±0.05 %
Setpoint accuracy is inversely proportional to the input
span.
INPUT SPECIFICATIONS
■ DC Current: Input resistor incoporated
(If not specified, the input range is 4 – 20 mA DC.)
Input range: 0 – 50 mA DC
[Example] Input type 0 – 50 mA, Input range 4 – 20 mA
Max. Input Range (50 mA) ÷ Span (16 mA) × 0.05 %
= ±0.16 %
Minimum span: 2 mA
Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span
Response time: ≤ 0.2 sec. (0 – 100 % at 90 % setpoint)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
■ DC Voltage
•Code S1 (narrow spans)
Input range: -1000 – +1000 mV DC
Minimum span: 100 mV
•Code S2 (wide spans)
STANDARDS & APPROVALS
EU conformity:
Input range: -10 – +10 V DC
Minimum span: 1 V
EMC Directive
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
If not specified, the input range is shown below.
S1: 0 – 100 mV DC
EMI EN 61000-6-4
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1
S2: 1 – 5 V DC
Measurement Category II (output)
Pollution Degree 2
OUTPUT SPECIFICATIONS
■ Relay Output
Input or power to output: Reinforced insulation (300 V)
Input to power: Basic insulation (300 V)
RoHS Directive
Relay rating:
250 V AC @2 A (cos ø = 1)
EN 50581
30 V DC @2 A (resistive load)
Maximum switching voltage: 250 V AC or 125 V DC
Maximum switching power: 500 VA or 60 W
Minimum load: 5 V DC @100 mA
Mechanical life: 5 × 10 cycles (rate 180/min.)
6
Alarm Trip Operation Terminal No. in parentheses
• Setting Example
Hi alarm (coil energized at alarm) or
Lo alarm (coil de-energized at alarm)
(3–2)ON
Output
(3–4)ON
Input
(%)
0
50
100
Setpoint
Trip operation in power failure: Terminals 3 – 4 turn ON.
M6DXAS SPECIFICATIONS
ES-7828 Rev.8 Page 2/4
http://www.m-system.co.jp/
MODEL: M6DXAS
EXTERNAL VIEW
FRONT VIEW (with the cover open)
SIDE VIEW
5
6
7
8
Power LED
Alarm Monitor LED
Input Selector
Status Indicator LED
Configurator Jack
v
I
1
2
3
4
The DIP switch setting is required to select input types
before setting a precise input range using PC Configurator
Software (model: M6CFG).
Refer to the instruction manual for detailed procedures.
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
WIRE INSERTION ANGLE: approx. 7°
8–M3
EURO TERMINAL
DIN RAIL HOOK
5
6
7
8
DIN RAIL
35mm wide
1
2
3
4
SCREWDRIVER
INSERTION ANGLE
: approx. 40°
[0.5 (.02)]
5.9 (.23)
102 (4.02)
• When mounting, no extra space is needed between units.
M6DXAS SPECIFICATIONS
ES-7828 Rev.8 Page 3/4
http://www.m-system.co.jp/
MODEL: M6DXAS
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
STATUS ALARM
IND. LED MONITOR LED
INPUT
SELECTOR
N.C.
4
2
3
Digital
Ry
+
–
Computation
5
N.O. OUTPUT
COM
Low Drift
Amplifier
24.9 Ω
INPUT
6
POWER LED
1
+
7
8
POWER
–
CONFIGURATOR
JACK
POWER
■ Relay Protection
• AC Powered
• DC Powered
Inductive
Load (Coil)
Inductive
Load (Coil)
LOAD
LOAD
U
Diode, Varistor or
CR Circuit
Varistor or CR Circuit
Specifications are subject to change without notice.
M6DXAS SPECIFICATIONS
ES-7828 Rev.8 Page 4/4
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明